Search Results

Search found 33971 results on 1359 pages for 'ask and learn'.

Page 381/1359 | < Previous Page | 377 378 379 380 381 382 383 384 385 386 387 388 | Next Page >

Is a disk/ata timeout exception dangerous?

- by j-g-faustus

I have a few hard drives in mdadm RAID 5 configured to go to standby after a few minutes of inactivity. (Using hdparm.conf spindown_time.) At irregular intervals I get messages like these in dmesg: [ 1840.251661] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 1840.251722] ata4.00: failed command: SMART [ 1840.251758] ata4.00: cmd b0/d5:01:06:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in [ 1840.251759] res 40/00:14:50:2e:04/00:00:02:00:00/40 Emask 0x4 (timeout) [ 1840.251858] ata4.00: status: { DRDY } [ 1840.251888] ata4: hard resetting link [ 1840.600742] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1840.601521] ata4.00: configured for UDMA/133 [ 1840.601547] ata4: EH complete [337877.713988] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [337877.714019] ata4.00: failed command: SMART [337877.714038] ata4.00: cmd b0/d5:01:06:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in [337877.714039] res 40/00:04:90:10:81/00:00:00:00:00/40 Emask 0x4 (timeout) [337877.714089] ata4.00: status: { DRDY } [337877.714107] ata4: hard resetting link [337878.063085] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [337878.063743] ata4.00: configured for UDMA/133 [337878.063764] ata4: EH complete I think the exception is caused by smartd when a drive does not wake up quickly enough. There are no issues (that I can tell) in accessing the drives normally through the file system - it takes a few seconds longer than normal when they are asleep, but there are no exceptions. Is this something I should worry about, as a potential symptom on something that could corrupt a drive over time? Or can I safely ignore it as part of normal operation? Edit: By request: smartctl -a for sdaand sde, both disks are members of the array. If ata4is the same as scsi-4 then sde is the one that gave the error above, according to /dev/disk/by-path.

Read the article
Printing with Lacie Lightscribe requires root privileges

- by James

I have installed Lacie Lightscribe software on Ubuntu 12.04. Everything seems to be fine, the drive is detected, the proper media is detected, but when I click print I get the message "Printing Requires Root Privileges". I am the main (administrator) account on this computer, part of the sudo group and I cannot seem to find an answer to this dilemna in plain english. I've seen some apparently relevant posts which say things like "check whether the files /usr/4L/4L-gui and /usr/4L/4L-cli have any setuid-bits set. If so, remove them" but I need more detailed step-by-step instructions than that, please. Is there anyone who knows how to solve this?

Read the article
Coda-like experience for Ubuntu

- by Dillon Gilmore

I'm a web developer who's going to transition from using Mac OS X to Ubuntu. I've been using Coda for some time, only because it makes web development easy. I know a full fledged app isn't available for Linux, but would like to know about apps that specialize in the same tasks that Coda offers. I plan on switching to Vim for code editing, I'm extremely proficient and will install the Janus plugin and be good to go for editing code. One thing that makes editing on Coda so amazing is its extremely good at SFTP, you can drag and drop files and/or folders from your local drive to the server. Also, you can edit code directly on the server. The problem here, is that using Vim I don't know of a way to edit code on a remote server, while using my own Vim settings and plugins. To solve this, I would like to know of a good SFTP client OR a good SFTP CLI. A CLI that could synchronize your files after a file has been modified would be perfect, but not necessary. Now, one of the biggest and best features of Coda is its ability to view your databases. You get to create a database, create tables, add stuff, delete stuff and view the contents of the table (all this without writing a single SQL statement). I will admit that databases are my weak point, but is a very important part of my job. If there is a tool that specializes in databases would be perfect. I wouldn't prefer to use the command line for database stuff, but if there is a CLI for databases that I'm missing could potentially be useful. So I guess I'm asking for two things. A tool that makes databases easier to visualize and a tool that assists in pushing my local code to a server.

Read the article
Do I need a wifi card to have internet access?

- by Sarah

I am attempting to set up a wireless network on 11.04, freshly download today. The router is on and working. However, I do not have a wifi "card" (which I am assuming is a little USB-type thing that allows internet access, but correct me if I am wrong) and every time I try to type in the MAC address and everything, nothing works. I also get the "firmware missing" error when I scroll over the signal strength, which I have tried looking up but have been unsuccessful with completely understanding it. I guess my main question is do I need another little device to be able to use wifi on my ubuntu? I do have an ethernet cable but another person is using it and I do not want to be tied down to that cable. the problem is that none of the wireless networks show up, however they show up when I go into Windows mode on my laptop. I get an error message at the top saying "firmware missing" which I have tried looking up but still have no straight answer for.

Read the article
How do I control remote Windows 7 machine? VNC/RDP/?

- by artfulrobot

I have a Windows 7 laptop that's going out and about and I'd like to be able to admin' it from my Ubuntu (precise) desktop. While the laptop is in my office I can use Gnome's "Remote Desktop Viewer" (Vinagre) to connect via RDP. However, when it's in the office I don't really need RDP of course! And when it's out of the office I cannot control the routers/firewalls along the way, so I won't know the IP and cannot set up port forwards. I'm looking for a Ubuntu compatible way to achieve this. Nb. I can set up port forwards at the my office end, so a service on the laptop could try a "backwards" connection to my client.

Read the article
Fresh Ubuntu Install - Grub not loading

- by Ryan Sharp

System Ubuntu 12.04 64-bit Windows 7 SP1 Samsung 64GB SSD - OS' Samsung 1TB HDD - Games, /Home, Swap WD 300'ishGB HDD - Backup Okay, so I'm very frustrated, so please excuse me if I miss anything out as my head is clouded by anger and impatience, etc. I'll try me best, though. First of all, I'll explain how I got to my predicament. I finally got my new SSD. I firstly installed Windows, which completed without a hitch. Afterwards, I tried to install Ubuntu, which failed several times due to problems irrelevant to this question, but I mention this to explain my frustrations, sorry. Anyway, I finally installed Ubuntu. However, I chose the 'bootloader' to be installed on the same partition as where I was installing the Ubuntu Root partition, as that was what I believed to be the best choice. It was of my thinking that it was supposed to go on the same partition and on the SSD, which is my OS drive, though with my problem, it apparently was wrong. So I tried to fix it by checking guides and following their directions, but seemed to have messed it up even more. Here is what I receive after I use the fdisk -l command: (I also added explanations for which I used each partition for) Disk /dev/sda: 64.0 GB, 64023257088 bytes 255 heads, 63 sectors/track, 7783 cylinders, total 125045424 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x324971d1 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 208896 48957439 24374272 7 HPFS/NTFS/exFAT /dev/sda3 48959486 125044735 38042625 5 Extended /dev/sda5 48959488 125044735 38042624 83 Linux sda1 --/ Windows Recovery sda2 --/ Windows 7 sda3/5 --/ Ubuntu root [ / ] Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc0ee6a69 Device Boot Start End Blocks Id System /dev/sdb1 1024208894 1953523711 464657409 5 Extended /dev/sdb3 * 2048 1024206847 512102400 7 HPFS/NTFS/exFAT /dev/sdb5 1024208896 1939851263 457821184 83 Linux /dev/sdb6 1939853312 1953523711 6835200 82 Linux swap / Solaris sdb3 --/ Partition for Steam games, etc. sdb5 --/ Ubuntu Home [ /home ] sdb6 --/ Ubuntu Swap Partition table entries are not in disk order Disk /dev/sdc: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x292eee23 Device Boot Start End Blocks Id System /dev/sdc1 2048 625141759 312569856 7 HPFS/NTFS/exFAT sdc1 --/ Generic backup I also used a Boot Script that other users suggested, so that I can give more details on my partitions and also where Grub is located... ============================= Boot Info Summary: =============================== => Grub2 (v1.99) is installed in the MBR of /dev/sda and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks for (,msdos5)/boot/grub on this drive. => Grub2 (v1.99) is installed in the MBR of /dev/sdb and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks for (,msdos5)/boot/grub on this drive. => Windows is installed in the MBR of /dev/sdc. Now that is weird... Why would Grub2 be installed on both my SSD and HDD? Even weirder is why is Windows on the MBR of my backup hard drive? Nothing I did should have done that... Anyway, here is the entire Output from that script... PASTEBIN So, to summarize what I need: How can I fix my setup so grub loads on startup? How can I clean my partitions to remove unnecessary grubs? What did I do wrong so that I don't do something so daft again? Thank you so much for reading, and I hope you can help me. I've been trying to have a successful setup since Friday, and I'm almost at the point that I'm really tempted to throw my computer out the window due to my frustration.

Read the article
What's up with all the updates? [closed]

- by Bob Babb

I use Ubuntu exclusively for my job, especially for the fact that everything works and I get the most out of my processor and memory, but you are killing me with updates! I just lost a very good opportunity from a client that installed Ubuntu but got tired of all the updates. I really can't argue the fact. In a matter of a day I had two software updates. Quote from customer: "It's sad that I come in at 6:00 in the morning to install updates from a LTS version, and then before I leave at the end of the day I have 19 new updates to install. At least Microsoft bundles them in controllable groups." Sadly I have to agree, guys you have to do something about this. Please!

Read the article
Resize Partition with gparted

- by arian

I wanted to create more space for Ubuntu on my hard disk in favor of my windows partition. I booted the livecd and resized the ntfs partition to 100gb. Then I wanted to resize my ubuntu (ext4) partition to fill up the created unallocated space. A screenshot of my current disk. (With the livecd there's no 'key' icon after sda6) My first thought was just right click on sda6 ? move/resize ? done. Unfortunately I cannot resize or move the partition. However I can resize the ntfs partition. I guess it is because the extended sda4 partition is locked. I couldn't see an unlock possibility though… So how do I resize the ext4 partition anyway, probably by unlocking the extended partition, but how? Thanks in advance.

Read the article
Text reverses on remote gnome session

- by Andrew Stern

I have two computers running 10.4 . The first machine is a wired desktop with sshd. The second is a wifi connected laptop with the ssh client. When I use my laptop to bring up a remote gnome session to my desktop all the text gets reversed. Steps: 1) login as a user on the laptop to activate the wifi with a stored key. 2) goto a console Ctrl-Alt F1 3) do a xterm -- :1 to bring up a blank graphic session 4) ssh -Y user@desktopmachine gnome-session This shows reversed text and messes up the keyboard so I can't type

Read the article
Access a mounted Windows share from the command line

- by Bryan

Hello All, I use the "Connect to Server..." option under the "Places" menu to connect to a Windows share in my work environment. When I do so, I can access the Windows share via Nautilus, but I can't figure out how to access the share from the command line without using smbclient. For example, the share isn't mounted under /mnt or /media. Is it possible to access the mounted Windows share from the command line without using smbclient?

Read the article
Settings are not being saved

- by Gavin Panella

Several weeks ago I updated a Facebook and Google accounts in Empathy to use per-application passwords. However, it forgets these passwords on each reboot and I have to enter them again. However, settings in Edit with Emacs in Chromium do not persist either, so I think this is more than a bug in Empathy. I tried mv ~/.gconf ~/.gconf.bak, but that didn't work. What other common denominators are there that might be at the root of this?

Read the article
Problem using graphics.h in Ubuntu

- by blooooomer

# include<stdio.h> # include<graphics.h> # include<math.h> using namespace std; int main(void) { int gd=DETECT,gm; int r,x,y,p,xc=320,yc=240; initgraph(&gd,&gm,NULL); cleardevice(); printf("Enter the radius "); scanf("%d",&r); x=0; y=r; putpixel(xc+x,yc-y,1); p=3-(2*r); for(x=0;x<=y;x++) { if (p<0) { y=y; p=(p+(4*x)+6); } else { y=y-1; p=p+((4*(x-y)+10)); } putpixel(xc+x,yc-y,1); putpixel(xc-x,yc-y,2); putpixel(xc+x,yc+y,3); putpixel(xc-x,yc+y,4); putpixel(xc+y,yc-x,5); putpixel(xc-y,yc-x,6); putpixel(xc+y,yc+x,7); putpixel(xc-y,yc+x,8); } getch(); closegraph(); } installed graphics.h compiled using gcc filename.cpp -0 filename -lgraph then used ./filename the window apperared for 10 seconds and the error below appears: [xcb] Unknown sequence number while processing queue [xcb] Most likely this is a multi-threaded client and XInitThreads has not been called [xcb] Aborting, sorry about that. heart: ../../src/xcb_io.c:273: poll_for_event: Assertion `!xcb_xlib_threads_sequence_lost' failed. Aborted Any solutions?

Read the article
apt-get failed install of libg15, all package management is failing

- by Stifle

I was trying to get my Logitech G510 keyboard's back-lights working so I went into the Synaptic Package Manager and marked LibG15, G15daemon, and all the other associated packages. Synaptic reported a failed install. Now all Package management is failing due to libg15 being "halfway installed." Some commands I have tried to fix the problem follow. . . root@bt:~# apt-get upgrade Reading package lists... Done Building dependency tree Reading state information... Done E: The package libg15 needs to be reinstalled, but I can't find an archive for it. root@bt:~# sudo apt-get autoremove Reading package lists... Done Building dependency tree Reading state information... Done E: The package libg15 needs to be reinstalled, but I can't find an archive for it. root@bt:~# sudo apt-get -f purge libg15 Reading package lists... Done Building dependency tree Reading state information... Done E: The package libg15 needs to be reinstalled, but I can't find an archive for it. root@bt:~# sudo dpkg --configure -a dpkg: dependency problems prevent configuration of g15macro: g15macro depends on g15daemon; however: Package g15daemon is not configured yet. dpkg: error processing g15macro (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of g15stats: g15stats depends on g15daemon; however: Package g15daemon is not configured yet. dpkg: error processing g15stats (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: g15macro g15stats I'm not too computer savvy. Any help would be much appreciated!!! Note: I'm using Ubuntu 10.04 under Backtrack 5 R3.

Read the article
How to configure VNC on a remote Ubuntu server?

- by Jason H.

I am currently in the process of creating a Ubuntu server with Rackspace cloud and I am trying to configure this server for VNC over SSH on my MacBook Air. Here is a summary of what I am trying to accomplish. Server Details: Ubuntu 12.04 Hosted by RackSpace (no physical access) Need to run Gnome3 VNC connection must be over SSH Any guides or assistance would be great, I have installed Gnome3 and Vino for the VNC-server. I'm just not sure how to configure VNC properly. I've looked online but I'm stuck at the VNC-server portion.

Read the article
Issue with setting up multiple IP addresses on ubuntu server installation

- by varunyellina

I want to setup two ip addresses on my system for access through lan. This is my config on my other system. Desktop Installation My desktop installation runs with multiple IP's added through networkmanager both through lan and wifi. Server Installation On my server install I've edited /etc/network/interfaces to the following. auto eth0 auto eth0:1 # IP-1 iface eth0 inet static address 172.16.35.35 network 172.16.34.1 netmask 255.255.254.0 broadcast 172.166.35.255 dns-nameservers 172.16.100.221 8.8.8.8 # IP-2 iface eth0:1 inet static address 172.16.34.34 network 172.16.34.1 netmask 255.255.254.0 gateway 172.16.34.1 broadcast 172.16.35.255 After restarting through "/etc/init.d/networking restart" I recieve "Failed to bring up eth0:1" What am I doing wrong? Thankyou.

Read the article
Network manager indicator missing

- by Jarmo

I recently upgraded from 11.10 to 12.04. My first attempt failed, and I received an error stating that not all of the required packages were downloaded. Before (successfully) attempting again, I noticed that there was no longer a networking indicator in the upper panel. The indicator did not reappear with the installation of 12.04. To be clear, my wireless connection has experienced no problems, despite the missing indicator. Here are the solutions that I have found which did not work for me: Editing /etc/NetworkManager/NetworkManager.conf and replacing [ifupdown] managed=false with =true. Reinstalling network-manager (via apt-get install --reinstall). I am currently running 12.04 on an Asus Eee PC 1005 HA, and I am new to seeking solutions through forums, so I apologize if I have neglected to provide some vital information about my hardware.

Read the article
unable to enter bios

- by fraz

I have an asus desktop ( amd phenom X6 processor) which was preinstalled with windows 7. I wanted to install ubuntu on it (dual boot) but am unable to do so because of the boot order. So I thought of changing boot order thru bios. But it turns out, if I press any key while the computer is starting, it just doesnt boots. I can see that the keyboard and mouse are booted up. (the lights are on) but the monitor is in standby mode.. I tried tab, f2,f10, delete key. But nothing is working.. Is there a software or other alternate on how can I change boot order ? Thanks

Read the article
How to automatically visit a website in the background after Ubuntu booted?

- by Bakhtiyor

I wanted to know how to automatically visit a website in the background when Ubuntu loads. As far as I know w3m is for visiting web site from the console. That is why I am writing following command in the crontab -e. @reboot w3m http://example.com/ > test_file The reason for writing content of the web site into a test_file is just to know whether this command has been executed or no. Unfortunately it is not executing every time Ubuntu loads. But next command which comes after it and looks like this: @reboot date >> reboot_file is being executed every time. What is wrong with my command? When I execute it in the console it outputs the content of the example.com into test_file. Is there any other options to do that?

Read the article
GTK applications do not start

- by Greg

Hello, I have a fresh install of Ubuntu 10.04 Server on nodes of a computational cluster, and I access the nodes via ssh. I configured a X server, which I start with the command startx -- -ac. The server is running fine on port :0. Then, I set the environment variable DISPLAY to :0. Now, when I run a GTK application on the node, it fails with the following error: Error: Unable to initialize gtk, is DISPLAY set properly? Now, my question is, is there any runtime library that I need for running GTK applications on top of a X server? I'm probably missing something obvious here, but I can't tell what :P

Read the article
How do I get keyboard to write hiragana instead of katakana?

- by Lisandro

I added the Japanese Layout in Keyboard preferences, however all the layouts look like being in katakana. I suspect that the key that is left of number 1 (above Tab and under Esc) could be the one to switch from katakana to hiragana however I don't have that key in my keyboard and my other Toshiba laptop does not have it either. I really don't know what to do, I simply want to be able to write in hiragana in Ubuntu. Thanks

Read the article
Forcing Nautilus to use Kerberos (Active Directory) authentication

- by user14146

Is there a way to get Nautilus or any other file manager that runs on Ubuntu 11.04 to use Kerberos for authentication? I'm using Likewise Open to join machines to the domain, and I can't type in passwords for every user on every computer that needs to mount a network share. I've been able to get Kerberos working with the command line smbclient, but oddly Kerberos does not seem to be Nautilus-integrated. I also checked the SSH config file, and it looks like you can enable GSSAPIAuthentication, but it only works for Kerberos v2, not the current version, which I think is v5.

Read the article
Failed to download repository information (Maveric)

- by Rhiannon

I have been through most of the duplicates for this question, and still can't find an answer. I may have missed one but hopefully this isn't a duplicate! Having a problem with updates. I get the "failed to download..."message followed by "Check your internet connection", which is clearing working fine as I am on it now. I click details and get the following **W:Failed to fetch http://archive.ubuntu.com/ubuntu/dists/maverick-updates/multiverse/source/Sources 404 Not Found [IP: 91.189.92.202 80] , W:Failed to fetch http://archive.ubuntu.com/ubuntu/dists/maverick-updates/universe/source/Sources 404 Not Found [IP: 91.189.92.202 80] , W:Failed to fetch http:// archive.ubuntu.com/ubuntu/dists/maverick-updates/multiverse/binary-i386/Packages 404 Not Found [IP: 91.189.92.202 80] , W:Failed to fetch http:// archive.ubuntu.com/ubuntu/dists/maverick-updates/universe/binary-i386/Packages 404 Not Found [IP: 91.189.92.202 80] , W:Failed to fetch http:// archive.ubuntu.com/ubuntu/dists/maverick-security/multiverse/source/Sources 404 Not Found [IP: 91.189.92.202 80] , W:Failed to fetch http:// archive.ubuntu.com/ubuntu/dists/maverick-security/universe/source/Sources 404 Not Found [IP: 91.189.92.202 80] , W:Failed to fetch http:// archive.ubuntu.com/ubuntu/dists/maverick-security/multiverse/binary-i386/Packages 404 Not Found [IP: 91.189.92.202 80] , W:Failed to fetch http:// archive.ubuntu.com/ubuntu/dists/maverick-security/universe/binary-i386/Packages 404 Not Found [IP: 91.189.92.202 80] , E:Some index files failed to download. They have been ignored, or old ones used instead.** All the faults have "maveric" somewhere in them, so I have gone to settings and unticked all the Mavarics I can find, but this problem is still happening. Any ideas? Many thanks

Read the article
How to force a clock update using ntp?

- by ysap

I am running Ubuntu on an ARM based embedded system that lacks a battery backed RTC. The wake-up time is somewhere during 1970. Thus, I use the NTP service to update the time to the current time. I added the following line to /etc/rc.local file: sudo ntpdate -s time.nist.gov However, after startup, it still takes a couple of minutes until the time is updated, during which period I cannot work effectively with tar and make. How can I force a clock update at any given time? UPDATE 1: The following (thanks to Eric and Stephan) works fine from command line, but fails to update the clock when put in /etc/rc.local: $ date ; sudo service ntp stop ; sudo ntpdate -s time.nist.gov ; sudo service ntp start ; date Thu Jan 1 00:00:58 UTC 1970 * Stopping NTP server ntpd [ OK ] * Starting NTP server [ OK ] Thu Feb 14 18:52:21 UTC 2013 What am I doing wrong? UPDATE 2: I tried following the few suggestions that came in response to the 1st update, but nothing seems to actually do the job as required. Here's what I tried: Replace the server to us.pool.ntp.org Use explicit paths to the programs Remove the ntp service altogether and leave just sudo ntpdate ... in rc.local Remove the sudo from the above command in rc.local Using the above, the machine still starts at 1970. However, when doing this from command line once logged in (via ssh), the clock gets updated as soon as I invoke ntpdate. Last thing I did was to remove that from rc.local and place a call to ntpdate in my .bashrc file. This does update the clock as expected, and I get the true current time once the command prompt is available. However, this means that if the machine is turned on and no user is logged in, then the time never gets updates. I can, of course, reinstall the ntp service so at least the clock is updated within a few minutes from startup, but then we're back at square 1. So, is there a reason why placing the ntpdate command in rc.local does not perform the required task, while doing so in .bashrc works fine?

Read the article
MPlayer does not work

- by Soham Pal

Using the xubuntu desktop, on Ubuntu Raring updated from Quantal. MPlayer never really worked. No video, no audio, nothing. I really can't be any more helpful, so here's the log: petey@home-pc:~$ mplayer "/home/petey/Downloads/Polar Bear Cafe (480p)HorribleSubs]/[HorribleSubs] Polar Bear Cafe - 01 [480p].mkv" MPlayer SVN-r35984-4.7 (C) 2000-2013 MPlayer Team Playing /home/petey/Downloads/Polar Bear Cafe (480p)[HorribleSubs]/[HorribleSubs] Polar Bear Cafe - 01 [480p].mkv. libavformat version 55.0.100 (internal) libavformat file format detected. [lavf] stream 0: video (h264), -vid 0 [lavf] stream 1: audio (aac), -aid 0 [lavf] stream 2: subtitle (ass), -sid 0 VIDEO: [H264] 848x480 0bpp 23.810 fps 0.0 kbps ( 0.0 kbyte/s) Clip info: creation_time: 2012-04-05 21:36:10 Load subtitles in /home/petey/Downloads/Polar Bear Cafe (480p)[HorribleSubs]/ Can't open /dev/fb0: Permission denied [fbdev2] Can't open /dev/fb0: Permission denied VO: [v4l2] No such file or directory vo_cvidix: No vidix driver name provided, probing available ones (-v option for details)! [cyberblade] Error occurred during pci scan: Operation not permitted [mach64] Error occurred during pci scan: Operation not permitted [mga] Error occurred during pci scan: Operation not permitted [mga] Error occurred during pci scan: Operation not permitted [nvidia_vid] Error occurred during pci scan: Operation not permitted [pm3] Error occurred during pci scan: Operation not permitted [radeon] Error occurred during pci scan: Operation not permitted [rage128] Error occurred during pci scan: Operation not permitted [s3_vid] Error occurred during pci scan: Operation not permitted [SiS] Error occurred during pci scan: Operation not permitted [unichrome] Error occurred during pci scan: Operation not permitted [VO_SUB_VIDIX] Couldn't find working VIDIX driver. ========================================================================== Opening video decoder: [ffmpeg] FFmpeg's libavcodec codec family libavcodec version 55.0.100 (internal) Selected video codec: [ffh264] vfm: ffmpeg (FFmpeg H.264) ========================================================================== ========================================================================== Opening audio decoder: [ffmpeg] FFmpeg/libavcodec audio decoders AUDIO: 44100 Hz, 2 ch, floatle, 0.0 kbit/0.00% (ratio: 0->352800) Selected audio codec: [ffaac] afm: ffmpeg (FFmpeg AAC (MPEG-2/MPEG-4 Audio)) ========================================================================== [AO OSS] audio_setup: Can't open audio device /dev/dsp: No such file or directory DVB card number must be between 1 and 4 AO: [null] 44100Hz 2ch floatle (4 bytes per sample) Starting playback... Movie-Aspect is 1.78:1 - prescaling to correct movie aspect. VO: [null] 848x480 = 854x480 Planar YV12 A: 4.7 V: 4.7 A-V: 0.002 ct: 0.083 0/ 0 22% 0% 0.5% 0 0 MPlayer interrupted by signal 2 in module: sleep_timer A: 4.7 V: 4.7 A-V: 0.001 ct: 0.083 0/ 0 21% 0% 0.5% 0 0 Exiting... (Quit)

Read the article
Change clock resolution to 1000 Hz

- by Ricky Robinson

I am running Ubuntu 12.04 and I need to change the clock resolution to 1000 Hz (now it's 250 Hz, the default value). I understand that I have to set it and then recompile the kernel, as for example described here. It's not clear, though, how I can do it from the terminal, as for instance the suggested make menuconfig won't work. Any tips? My current settings are: $ cat /boot/config-3.8.0-29-generic | grep HZ CONFIG_NO_HZ=y CONFIG_RCU_FAST_NO_HZ=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set # CONFIG_HZ_1000 is not set CONFIG_HZ=250 CONFIG_MACHZ_WDT=m

Read the article

< Previous Page | 377 378 379 380 381 382 383 384 385 386 387 388 | Next Page >