Search Results

Search found 10402 results on 417 pages for 'macbook pro'.

Page 384/417 | < Previous Page | 380 381 382 383 384 385 386 387 388 389 390 391  | Next Page >

  • What are the biggest, best CPUs that support Physical Address Extension?

    - by Giffyguy
    I'm looking for a CPU that will support PAE and fit into an LGA775 socket. This combination of technology is very much preferred for my current server hardware/software setup. My priorities in order of highest to lowest: PAE & LGA775 At least 1066Mhz FSB Largest CPU cache possible Multiple Cores if possible HyperThreading if possible Most other factors are of little-to-no consequence. I'm finding it very difficult to figure out what my options are. Intel doesn't have much useful information on PAE (since x64 is so dominant), and Wikipedia simply says that "PAE is provided by Intel Pentium Pro (and above) CPUs - including all later Pentium-series processors except the 400 MHz bus versions of the Pentium M." All of Intel's listed Pentium CPU's support Intel64, which makes me seriously doubt they will support PAE with a 32-bit OS. And Wikipedia's claim is so vague, I have no idea if they mean up-to-and-including the x64 Prescott CPUs. PAE is supposed to be an aspect of the x86 architecture, and I believe it is no longer supported in an x64 environment. Please correct me if I am wrong.

    Read the article

  • How to Re-install an App that Shows up in the Appstore as 'Update' Instead of 'Buy App'

    - by Craig Reville
    So long story short: I dropped the wrong app into 'clean my mac' and I hit 'cancel' but it was too late by that point. I rebooted and appstore said it had an update, when I opened appstore it was showing an update for the app I just uninstalled. I tried clicking 'update' but it gives me an error saying it's unable to install after 'downloading'. When I try to go into 'purchased apps' it shows the app as uninstalled so I click 'install' and I get an error saying it's already installed. I'm running Lion OS X, latest version, updated, mac book pro is only a few months old. I tried searching through the entire system to remove all traces of the app, after rebooting appstore no longer shows the app and no longer shows the update but on the apps page it still says 'Update'. I tried reinstalling the app from desktop OUT of the appstore and again says the app is 'already installed'. So after reading more about lion I found an article that spoke about 'BundleID' being the thing that tells appstore what's installed and needing updating however I can't find the location of where the BundleID would be. Any thoughts? I've tried CCleaner, AppCleaner etc and none of them show the app, mainly because it is uninstalled. Update I've spoken to Apple Support who confirmed that there is a file in the system that connects separately to tell the system if there are updates available however they declined to inform me of any further details. Apple also referred me from technical support to iTunes App Store opposed to Mac App Store support and from there I have been referred to AppleCare who are currently 'investigating' this issue. Hopefully there will be a fix that's simple to implement for people having similar issues, this appears to be a more common issue than I previously thought.

    Read the article

  • Resize a RAID 1 volume on OS X Snow Leopard - how? (Note: software raid)

    - by Emmel
    I've scoured the Internet in search of an answer to this question, and as usual with OSX-related topics, I often don't find any deep-dive technical explanations sufficient enough to feel confident doing dangerous things. Here is my question: I have a Mac Pro, running OS X 10.6.2. I have, as my main root/boot disk, a RAID 1 volume called "Mirror1". Mirror1 is comprised of two 1 TB disks. Mirror1, however, is fixed at 640 GB. That's because, I originally took a 640GB disk, bought a terabyte disk, mirrored it (using diskutil appleraid enable), when it synced I removed the 640GB and replaced it with a second 1 TB disk, and synced again. Voila! A single 640 GB replaced by two 1 TB disks in a mirror.. Actually, no. There's still something missing from the equation: Mirror1 needs to be expanded from 640GB to 1 TB to match the partition sizes on each of those disks. How do I do this? Perhaps the diskutil output will help: -> diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk0 1: EFI 209.7 MB disk0s1 2: Apple_RAID 999.9 GB disk0s2 3: Apple_Boot Boot OSX 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk1 1: EFI 209.7 MB disk1s1 2: Apple_RAID 999.9 GB disk1s2 3: Apple_Boot Boot OSX 134.2 MB disk1s3 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *640.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Mac Disk 2 536.7 GB disk2s2 3: Microsoft Basic Data BOOTCAMP 103.1 GB disk2s3 /dev/disk3 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Mirror1 *639.8 GB disk3 -> diskutil appleraid list AppleRAID sets (1 found) =============================================================================== Name: Macintosh HD Unique ID: 1953F864-B474-4EB6-8E69-41834EBD0247 Type: Mirror Status: Online Size: 639.8 GB (639791038464 Bytes) Rebuild: manual Device Node: disk3 ------------------------------------------------------------------------------- # Device Node UUID Status ------------------------------------------------------------------------------- 0 disk1s2 25109BAE-5697-40EA-B612-0217851444F7 Online 1 disk0s2 11B83AB0-8148-4DB6-8761-DEF08C855F8D Online =============================================================================== Thanks in advance.

    Read the article

  • No video signal at boot with custom built computer

    - by Bart Pelle
    After booting my custom built computer, neither the VGA nor the HDMI methods from the video card seem to emit any signal to the display. I have tested both a regular VGA screen and a modern HDMI screen. Both did not receive signal. Below are the specifications from my computer build: Intel Core i5 3350P ASRock B75 Pro 3-M Seagate Barracuda 7200.14 ST1000 DM003 1000GB Corsair Vengeance LP CML 8GX 3M2 A1600 CGB Blue (2 cards) Cooler Master B Series B600 Club 3D Radeon HD7870 XT Jokercard Samsung SH-224 BB Black Sharkoon T28 Case The motherboard does not emit any beeps on startup. The CD tray opens properly and all fans spin. All cables are properly connected. All components are new and no damage was found on any of the components. The fans on the GPU spin aswell. The VGA test we did was by using the onboard graphics from the Intel i5, but this gave no result. The HDMI test was from the GPU which did not emit any signal either. We have not been able to test out the DVI, could this be important to test, even though all the other methods did not work? Thank you for your time and hopefully reply.

    Read the article

  • Why is my second monitor not working?

    - by StampedeXV
    Since I have my new computer, I have a very weird problem. Facts: New Computer: Motherboard: ASRock Z77 Pro 3 Graphics-card: Asus1GB D5 X EN GTX560 DCII OC/2DI R CPU: Intel i5-3570 Windows 7 64bit 500W beQuiet special edition (92% efficiency) 8GB 1333MHz DDR3 Corsair RAM (CL9) Scythe Mugen 2 2 magnetic HDDs + 1 SDD 1 DVD-R Old Computer: Motherboard: Asus P55 something Graphics-card: Asus1GB D5 X EN GTX560 DCII OC/2DI R CPU: Intel i7-870 Windows 7 64bit 550W Corsair 8GB 1333MHz DDR3 Corsair RAM (CL9) Scythe Mugen 3 2 magnetic HDDs + 1 SDD 1 DVD-R On the old computer it worked fine with two monitors. Moving to the new (I took the same Graphics-card) it only works with one. The weird thing I mentioned is: not matter which one. But if I put both there, only one is available. There is no reaction at the start (where normally (at least if I remember correctly) the monitor shortly went from "standby" to "on"). Windows does not recognize a second monitor in the Device Manager. I have the latest drivers for Motherboard and Graphics-card. I have the latest BIOS drivers. I am out of ideas. Edit: completed computer setup

    Read the article

  • Damaged partition after disk image

    - by Charles Gargent
    I am trying to clone/backup a disk with Windows 7 Pro 64bit on it. First I tried Easus Todo Backup and used disk clone option without sector by sector copy. I then plugged in the new drive and I get the following error. "Invalid or damaged Bootable partition" I then plugged the old drive back in and I am greeted with the same error. My next step was to try the sector by sector disk clone, but still I get the same error. I have tried fixing the mbr with the windows disk but that makes no difference. I have tried some other free tools and I get the same error. I have tried this on a different machine running Windows 7 Enterprise 32bit without this problem. I have done some searching and the only thing I can come up with is this post from the Acronis forums http://forum.acronis.com/forum/8254 suggesting that the bios is reading my disk geometry incorrectly. Can anyone shed any light on this, is there a way I can fix this either in the bios or repair the mbr every time I reimage it?

    Read the article

  • Troubleshooting: Monitor never turns on, system fans running, DVD-ROM does not open.

    - by Wesley
    Hi all, Here are my specs beforehand: ECS P4VXASD2+ (V5.0) motherboard FSB 533MHz Intel Pentium 4 2.40A GHz Prescott Socket 478 2x 256MB PC2100 DDR RAM, 2x 256MB PC133 SDRAM CoolMax 350W PSU DVD-ROM - will edit with brand & model 128MB ATi Radeon 9800 Pro AGP No hard drive So, I just put those parts together today and I tried to power it up, with the monitor connected to the Radeon 9800 in the AGP slot (mobo does not have VGA port). After turning it on, the CPU fan, graphics fan and system fan go on. However, the monitor remains in standby mode, despite being plugged in. Also, after pushing the button on the DVD-ROM drive, it does not open. I've used the DVD-ROM drive before with absolutely no issues. The graphics card was slightly buggy when I put it on another machine, which was left outside in winter weather for 3 months. (Still that computer's integrated graphics worked fine.) CMOS battery was replaced and jumpers are all set correctly. Now, I'm wondering whether the motherboard, CPU, PSU or GPU is the problem. What can I do to test which part is the problem? Just to clarify, I don't have a hard drive, so I usually boot Ubuntu from the disc drive. Anyways, thanks in advance!

    Read the article

  • Coming from Win XP to 7 and having new accessibility software problems

    - by Anonymous Jones
    I just switched from Windows XP Pro SP3 (32bit) to Windows 7 Ultimate (32bit) on a new PC. Now, both the new onscreen keyboard and a utility for sending mouse clicks are being problematic. The problem with 7's OSK is that some things I type only work intermittently or just dodgily. Like Alt+Tab with multiple Tabs, other Alt/Ctrl/Shift/Win key combinations, and the context menu key. Sometimes apps will not take focus for input at all. I use the OSK it in 'hover' mode, on 0,5 seconds. The clicking tool is Point-N-Click, which sends clicks when I dwell anywhere for 1.25 seconds with the mouse pointer. http://www.polital.com/pnc/ The problem with it is that sometimes it fails to click. Most often this happens in some of the control panel sections, on the taskbar, and when UAC pops up. It seems to occur in conjunction with OSK usage a bit too, I think. I'm using an Administrator account. DEP and UAC settings are default. What can I do to fix or work around either of these problems? I'm disabled so this really is killing usability.

    Read the article

  • Constant crashes in windows 7 64bit when playing games

    - by yx
    I've tried everything I can possibly think of in trying to fix this problem and I'm totally out of ideas, so any help would be appreciated: The problem: whenever I fire up a game, it works for a short while with no problems and then it would crash. Either its a hard crash, forcing me to reboot, or windows would report that the display driver has stopped working and recovered. Here is a list of things I've already tried: Drivers - tried the latest drivers (catalyst 9.12) as well as the stock drivers that came with the video card. Also have the latest BIOS/chipset Memtest - Ran Memtest86+ overnight, had no problems, the windows diagnostic tool also does not find any problems. Overheating - Video card/cpu temperatures are well below peak (42 and 31 Celsius receptively) PSU Voltage - CPUID shows that the voltage levels are all above what they should be. The PSU itself is only roughly 16 months old and is a good model. HDD - No errors when checked GPU - Brand new (replaced previous card since I thought it was the problem, apparently not) Overclocking - Everything is at stock levels, memory voltage is set to manufacturer's standard Specs: Motherboard: ASUS P5Q Pro CPU: Core 2 Duo E8400 3.0 ghz OS: Windows 7 home premium 64 bit Memory: Mushkin Enhanced 4GB DDR2 GPU: Sapphire HD 5850 1GB PSU: SeaSonic M12 600W ATX12V DirectX: DX11 Event Viewer after a crash always has these logged: A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Bus/Interconnect Error Processor ID: 1 The details view of this entry contains further information. A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Bus/Interconnect Error Processor ID: 0 The details view of this entry contains further information. A previous card that I had (4850x2) also had these errors, so I changed video cards, but the same thing is happening.

    Read the article

  • Can you transfer a Windows 7 XP-mode VHD to a new PC without the need for reactivation?

    - by Henk
    Hi. At the moment I am running Vista 32 bit and use VPC 2007 a lot. I have several W2000 VMs set up with complex software configurations. For me, one of the advantages of working with VPCs is that a VM can easily be copied to another PC (like a notebook). Also, when I move to a new PC, I can immediately work with my existing VMs without the need to reinstall all applications. I am thinking about buying a new pc with Windows 7 64 bit pro, and using the xp-mode VM that comes with Windows 7. The advantages would be support for more memory (so being able to run more VM's simultaneously) and having a licenced XP VM. I would like to know if you can transfer a VHD that is based on the xp-mode VHD to another machine without Activation issues. The other machine will of course, also be running W7. I would guess that this would not be a problem. However, I did read about a guy who had to reinstall his W7 because of a harddisk failure, and could not access his xp-mode VHD anymore because it demanded re-activation. Thanks. Henk.

    Read the article

  • Server freezes while installing Redhat Enterprise Linux Server 6

    - by eisaacson
    We've tried both the first options Install or upgrade an existing system Install system with basic video driver When trying option #1, it gets to a screen that has a solid cursor about halfway down, then freezes. When trying option #2, it freezes at the point where it says: Waiting for hardware to initialize... Of course, we bought the unsupported version and haven't found anything to help us so far. Here are the specs to the server in the original post: ASUS P8Z68-M Pro LGA 1155 Intel Z68 HDMI SATA 6Gb/s USB 3.0 Micro ATX Intel Motherboard with UEFI BIOS RAIDMAX Reiter ATX-305WBP Black Steel / Plastic ATX Mid Tower Computer Case 450W Power Supply Intel Core i7-2600 Sandy Bridge 3.4GHz (3.8GHz Turbo Boost) LGA 1155 95W Quad-Core Desktop Processor Intel HD Graphics 2000 BX80623I72600 16GB Ram OCZ Agility 3 SSD 120GB From some of the posts out there could the UEFI Bios or the Sandy Bridge processor be a culprit here? We just tried the DVD on a different computer and it got past that point with ease. It's a standard Dell build compared to our custom machine. Could it be having difficulty recognizing drivers? How do we get past that?

    Read the article

  • Resize a RAID 1 volume on OS X Snow Leopard - how? (Note: software raid)

    - by Emmel
    I've scoured the Internet in search of an answer to this question, and as usual with OSX-related topics, I often don't find any deep-dive technical explanations sufficient enough to feel confident doing dangerous things. Here is my question: I have a Mac Pro, running OS X 10.6.2. I have, as my main root/boot disk, a RAID 1 volume called "Mirror1". Mirror1 is comprised of two 1 TB disks. Mirror1, however, is fixed at 640 GB. That's because, I originally took a 640GB disk, bought a terabyte disk, mirrored it (using diskutil appleraid enable), when it synced I removed the 640GB and replaced it with a second 1 TB disk, and synced again. Voila! A single 640 GB replaced by two 1 TB disks in a mirror.. Actually, no. There's still something missing from the equation: Mirror1 needs to be expanded from 640GB to 1 TB to match the partition sizes on each of those disks. How do I do this? Perhaps the diskutil output will help: -> diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk0 1: EFI 209.7 MB disk0s1 2: Apple_RAID 999.9 GB disk0s2 3: Apple_Boot Boot OSX 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk1 1: EFI 209.7 MB disk1s1 2: Apple_RAID 999.9 GB disk1s2 3: Apple_Boot Boot OSX 134.2 MB disk1s3 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *640.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Mac Disk 2 536.7 GB disk2s2 3: Microsoft Basic Data BOOTCAMP 103.1 GB disk2s3 /dev/disk3 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Mirror1 *639.8 GB disk3 -> diskutil appleraid list AppleRAID sets (1 found) =============================================================================== Name: Macintosh HD Unique ID: 1953F864-B474-4EB6-8E69-41834EBD0247 Type: Mirror Status: Online Size: 639.8 GB (639791038464 Bytes) Rebuild: manual Device Node: disk3 ------------------------------------------------------------------------------- # Device Node UUID Status ------------------------------------------------------------------------------- 0 disk1s2 25109BAE-5697-40EA-B612-0217851444F7 Online 1 disk0s2 11B83AB0-8148-4DB6-8761-DEF08C855F8D Online =============================================================================== Thanks in advance.

    Read the article

  • Windows 7 remote desktop encryption error every few minutes

    - by rfrankel
    Because of an error in data encryption, this session will now end. This is the error I've been getting more and more frequently over the past few days, to the point that I can't ignore it because it's happening consistently within 5 minutes of connecting - sometimes within a few seconds. Both the remote and local machines are Windows 7 Pro x64. The remote machine is behind a Linksys RV082, and I'm using UPnP to forward a remote port to the correct local port. This setup had been working fine for several months, and I can't think of any recent relevant changes that might have been made. Things I've already tried: Disabling unnecessary components of the network connection on the remote machine, until only IPv4 and Client for Microsoft Networks remain. Disabling TCP large send offload on both the remote and local machines. Confirming that the remote machine is not mentioned anywhere in any DMZ settings on the Linksys router. Confirming that there are no x509-related registry keys screwing things up (this is the suggested fix for a slightly different error anyway). These are the only solutions I've been able to find after about an hour of searching, and most of them apply to XP or Server 2003 in any case. If anyone could suggest something else, it would be much appreciated.

    Read the article

  • Windows Firewall Software to Filter Transit Traffic

    - by soonts
    I need to test my networking code for Nintendo Wii under the conditions when some specific Internet server is not available. Wii is connected to my PC with crossover ethernet cable. PC has 2 NICs. PC is connected to hardware router with ethernet cable. The hardware router serves as NAT and has an internet connected to its uplink. I set the Wii to be in the same lan as PC by using Windows XP Network bridge. I can observe the WII network traffic using e.g. Wireshark sniffer. Is there a software firewall that can selectively filter out transit traffic? (e.g. block outgoing TCP connections to 123.45.67.89 to port 443) I tried Outpost Pro 2009 and Comodo. Outpost firewall blocks all transit traffic with it's implicit "block transit packet" rule. If the transit traffic is explicitly allowed by creating the system-wide low level rule, then it's allowed completely and no other filter can selectively block it. Comodo firewall only process rules when the packet has localhost's IP as either source or destination, allowing the rest of the traffic. Any ideas? Thanks in advance! P.S. Platform is Windows XP 32 bit, no other OSes is allowed, Windows ICS (Internet Connection Sharing) doesnt work since the Wii is unable to connect, becides I don't like the idea of adding one more level of NAT.

    Read the article

  • Timeout option not working on efi windows 7/windows8 dual boot machine

    - by Guenter
    I hav a gigbyte GA-Z77m-D3h mobo and installed Windows 8 Pro and Windows 7 Ultimate on two SSDs (in that order) in EFI mode. Now when I start my computer, I get the windows boot menu (text mode) with the two OSses to choose, but I have to manually press RETURN to have the computer boot into the Win OS. Even if I wait an hour, no default action takes place. Using bcdedit (from either of the OSses) I can successfully change the time out value, and it shows up in the bcdedit (no params) output. But it doesn't fire ... Here is my current BCDEdit output (headers are in German, but values should be readable): Windows-Start-Manager --------------------- Bezeichner {bootmgr} device partition=O: path \EFI\Microsoft\Boot\bootmgfw.efi description Windows Boot Manager locale de-DE inherit {globalsettings} integrityservices Enable default {default} resumeobject {5ad2802c-c60a-11e2-acdb-80331c501b11} displayorder {default} {current} {5ad2802a-c60a-11e2-acdb-80331c501b11} {5ad28028-c60a-11e2-acdb-80331c501b11} {5ad28029-c60a-11e2-acdb-80331c501b11} toolsdisplayorder {memdiag} timeout 5 displaybootmenu Yes Windows-Startladeprogramm ------------------------- Bezeichner {default} device partition=W: path \Windows\system32\winload.efi description Windows 7 locale de-DE inherit {bootloadersettings} recoverysequence {5ad2802e-c60a-11e2-acdb-80331c501b11} recoveryenabled Yes osdevice partition=W: systemroot \Windows resumeobject {5ad2802c-c60a-11e2-acdb-80331c501b11} nx OptIn Windows-Startladeprogramm ------------------------- Bezeichner {current} device partition=C: path \Windows\system32\winload.efi description Windows 8 locale de-DE inherit {bootloadersettings} recoverysequence {5ad28033-c60a-11e2-acdb-80331c501b11} integrityservices Enable recoveryenabled Yes isolatedcontext Yes allowedinmemorysettings 0x15000075 osdevice partition=C: systemroot \Windows resumeobject {5ad28031-c60a-11e2-acdb-80331c501b11} nx OptIn bootmenupolicy Standard hypervisorlaunchtype Auto (this output is from Win8; the Win7 looks nearly identical) If maybe the problem comes from a bad EFI Windows boot manager installation, can this be fixed without loosing my windows installations?

    Read the article

  • Using the same Windows 8 Upgrade installer on multiple PCs

    - by Karan
    As per this article: You may transfer the software to another computer that belongs to you. … You may not transfer the software to share licenses between computers. But what if I have a bunch of PCs with a mix of XP/Vista/Windows 7? Can I purchase either the Windows 8 Pro Upgrade $40 (download only) or $70 (DVD) version (both of which come without a key) only once and use it to upgrade all the PCs? Since I'm not sharing the license and each PC has its own valid genuine license, it should be allowed, right, or is it illegal? Even if they want people to shell out $40/$70 for each PC, how would they enforce the use of the installer/media on only one PC each? EDIT: I have been given to believe by a source that the installer will only check for the previous OS' key, which is what is confusing me (I have never purchased an upgrade version before this, only full retail or pre-installed versions). Is this true or will I need to enter two keys to make the upgrade work, one for the previous version and then one for Windows 8? If the latter is the case, then the issue is solved since obviously the same Windows 8 key will not be valid for multiple PCs.

    Read the article

  • scalable yet doable small-medium office network

    - by Jared
    Hello, I'm studying up with both Microsoft and Cisco literature and I must say, my head is starting to get clustered up (pun intended). I've made a quick network diagram of a theoretical company... Company1 owns Company 2 and Company 3, which are all under separate rooms and networks, but must be able to share a few resources such as files or printers. Given the amount of info out there and best practices, I thought about posting here to get suggestions and see what would the pro's do. I can read and read all day and implement on my own, but if I dont get some outside input, how will I know if I'm doing something wrong, right? anyway, please take a look and see if this is an over-complicated network or a lackluster design for a small-medium company of about 35 people and lets say they will be double that number by end of the year... :) Using win2k3, esxi, windows xp. FCS - forefront client security, ACS - access control system, SPCWK - spiceworks, XCH - Exchange Im not allowed to post an image yet, so here's the link ---- GLIFFY IMAGE Flame suit is on just in case people get mad at me for making an "abomination". I'd really want to get the general overview properly before I dive into the more complicated things

    Read the article

  • Is this a solution for having multiple SSL certificates on the same IP

    - by Saif Bechan
    I am running CentOS running on a VPS. I read some guides on having multiple SSL certificates on the same system, but I can not get the basics to work. The guide I got that makes the most sense to me is the doing the following. In CentOS I can make virtual NIC's. So I made 2 virtual NIC's to start with. 192.168.10.1, 192.168.10.2. Now I work in ISP manager Pro, so this is listening on my primary ip 1.1.1.1 For each website I have them listening on 192.168.10.1:80, 192.168.10.1:443 In the hosts file I made the following 2 entries 192.168.10.1 1st.com 192.168.10.2 2nd.com Now the strange thing is that when I browser to 1st.com I do not get the website located at 192.168.10.1, I get the website located at my prim IP 1.1.1.1 Should I do something like forwarding or routing for this setup to work? And the basic question: Will this setup even work? Are the SSL certificates based on the IP adress, or are the based on the host name, 1st.com and 2nd.com.

    Read the article

  • Anonymous access to SMB share hosted on Server 2008 R2 Enterprise

    - by bwerks
    Hi all, First off, I have read through this post and a whole slew of non-SF posts which seem to address the same or a similar problem, however I was still unable to fix my problem. I've got three machines in this situation: a domain-joined server that runs Server 2008 R2 Enterprise ("share server") a domain-joined workstation running XP Pro SP3 ("test server") a domain-unjoined test server running Server 2003 R2 SP2 ("workstation") The share server is exposing a share on the network that the test server must access--it's a Source/Symbol Server share for our debugging purposes. I believe visual studio simply accesses the the share with its own credentials in this case, meaning that the share must be accessible anonymously since the test server isn't joined to the domain and there's no opportunity to supply domain authentication. I've attempted a lot of things to avoid the authentication window when accessing the share: I've enabled the Guest account on the share server and given Guest full sharing/NTFS permissions for the share. I've given ANONYMOUS LOGON full sharing/NTFS permissions for the share. I've added my share to “Network Access: Shares that can be accessed anonymously” in LSP. I've disabled “Network access: Restrict anonymous access to Named Pipes and Shares” in LSP. I've enabled “Network access: Let Everyone permissions apply to anonymous users” in LSP. Added ANONYMOUS LOGON to “Access this computer from the network” in LSP. Added the Guest account to “Access this computer from the network” in LSP. Attempted to provision the share using the Share and Storage Management MMC snap-in. Unfortunately when I attempt to access the share from the test server, I still see the prompt and I'm forced to enter "Guest" manually. I also tried this workflow using the local administrator account on a workstation, and the same thing happens both with and without XP Simple File Sharing enabled. Any idea why I'm getting these results, or what I should have done differently?

    Read the article

  • Sporadic email delivery to one user

    - by minamhere
    I have a user that occasionally does not receive emails from outside our organization. It does not seem to matter whether the other person is replying to an initial email or sending a new message. I have checked the Exchange System Manager and there is no record of the sender at all during this time period. No record of the message getting captured by the spam software (GFI Mail Essentials). The sender does not receive an NDR or any other indication that the message didn't arrive. It seems to me that these messages are not even getting to our servers at all. But, this is only impacting one user(that I am aware of) and not all the time. Some messages get through without any problem, others just disappear. The senders are not related at all. One is in another country, one uses AOL, one uses a corporate Exchange server locally. I can't seem to find a pattern. Where else can I look to try to figure out where these messages are going/getting captured? Are there additional logs that I can enable either within GFI or Exchange that might shed some light on this? Thanks. We are using Exchange 2003 on Server 2003. Desktop client is Outlook 2003 on Windows XP Pro.

    Read the article

  • Western Digital My Book not recognized by WD software

    - by Kari
    A few years ago I bought a WD My Book Pro 2. It worked fine for a while, then one of the drives failed and I sent it back to be replaced under warranty. I never got around to setting up the new one when I got it back. I finally ran out of room on my internal drive, so I tried to use the external - no go. Both drives spin up, but aren't recognized by either Disk Utility (Mac) or the WD Drive Manager. I tried on a PC as well with fresh software. Then I pulled the drives out of the enclosure (warranty is already expired) and plugged them straight into the PC. Both recognized and working 100% in RAID0. BIOS recognizes either disk as functional; Windows only sees them when both are connected due to the RAID which I can't change without the WD software. The drives that were returned to me are the "Green" drives which I've read are NOT recommended for RAID. Is it possible that this is interfering with them reading externally? Any other ideas? My main computer is a laptop so using them internally isn't an option :(

    Read the article

  • Windows 7 - Intermittently processes will not close when the app closes

    - by Bill Sambrone
    I have a user I am supporting who has the strangest issue. There are 2 problem applications, Word 2010 and a scanning program called ScandallPro. Intermittently (and at least once a day), she will close an app and the underlying process will not close. Both Word 2010 and this scanning software have all the latest updates. There is another user who has the same software that does not have this problem, and has identical hardware. I have formatted and rebuilt the computer for the user who is having the problems. After the rebuild, the machine was fine for a day but the scanning software continues to intermittently keep the process running even after it is closed. This is a problem because she cannot open a new instance of it while the process is still running. There is a boatload of line of business software on this machine, all of which she needs. I believe the Word 2010 issue is due to a misbehaving add-in (there are 2 add-ins, neither of which seem stable), and I think my best bet is to work with the add-in vendor on it. The scanning program staying open is isolated to this 1 user. The only difference between her machine and the other user is that she has Quickbooks, RoboForm, and Adobe Acrobat X Pro. Any ideas of what can be causing this, or other diagnostic steps to try?

    Read the article

  • NFS Datastore Appears Empty!

    - by daemonchild
    Hi guys, I've got an NFS server problem. The datastore connected and seems to be a valid datastore in both the vSphere client and under /vmfs/volumes. The issue is that it appears to be empty! I can create files (eg: touch /vmfs/volumes/nfs_common/thefile) and it is correctly written to the nfs store. I can verify this by looking on the nfs server itself. But the vmkernel only sees an empty datastore; the file disappears. Another freebsd box can mount the same NFS share and see the files correctly. Some useful data: ESXi 4.0.0 Build 208167 NFS is unfsd running on a Buffalo Linkstation Pro Duo (a bit hacky I know). The share has file system permissions set to 777 at the moment. My /etc/exports is as follows, and as I say it connects fine. /mnt/array1/ESX_Shared 192.168.16.0/255.255.255.0(insecure,rw,sync,no_root_squash,no_subtree_check) The ESXi servers can also successfully mount NFS shares from other NFS servers. Any ideas guys? Thanks, Tom

    Read the article

  • How do I stop VLC from stealing my volume buttons

    - by MGOwen
    when I press the volume buttons on my laptop, usually the system volume is changed. However, when I do this with VLC it "steals" the presses and adjusts it's own "volume" instead. The system volume is also changed. I can't find any way to turn this off in VLC. Does anyone know? Update: Sorry, some more details I should have included originally: VLC VERSION: 1.1.4 (and a few previous releases, back to about 1.1.0 or so, I think) OS: Win Vista Pro 32 HARDWARE: Dell 1720 laptop (the volume buttons are little buttons on the front of the unit, they may work something like "media" keyboard volume buttons) Update: The buttons seem to map to Ctrl+Alt+b and Ctrl+Alt+c (according to the shortcut key box in windows shortcut properties) but the VLC advanced preferences hotkeys screen doesn't list these as the keys it uses for volume. I changed it so there are no volume hotkeys in VLC settings - no luck it still steals the presses and adjusts the volume. Also, pressing Ctrl+Alt+b or c doesn't change my system volume, so who knows what windows or VLC are doing to recognise those volume buttons. :(

    Read the article

  • Radeon 6950 - Garbling of text and graphics in certain Windows only

    - by Greg
    This morning I noticed the text in Gmail (in Firefox 4) looked a little funny (kind of thin, maybe some color fringing). I went to work and thought it might be some ClearType issue or something with the way Direct way that FF4 draws to the screen. When I came back from work (I left the computer on), the problem was much worse - way beyond ClearType nit-picking. The text was barely readable. I opened Chrome and there was no such problem. It seems like only Windows that use hardware acceleration are garbled, and ones that use GDI are not. But, I fired up Dragon Age and didn't notice any problems (I only really looked at the main menu though). Here is a link to a screen shot that illustrates the problem. Notice how the Windows Live Mesh window is completely unreadable, the text in Firefox 4 (left) is pretty bad, while Chrome, the Windows Control Panel, and the task bar are perfectly fine. The fact that the problem shows up in screen shots and that it only happens in certain Windows makes me confident that the problem cannot be with the monitor or DVI cable. I am using the AMD Radeon drivers from 4/27/11. The card I have (MSI Frozr II) came with a slight overclock (810Mhz) out of the box, but it looks like when I'm on the Windows desktop it's not running at full clock (CCC reports 450Mhz). Still, I underclocked it to the stock reference clock (800Mhz) and it made no difference. The idle temperature according to Afterburner is 42-44 Celsius, which seems a tad high but not enough to cause a problem - it's cold to the touch if I open up the machine. What the heck could be causing this? The problem varies in intensity. As we speak I'm in Firefox and things look better than they did earlier - it'll probably get worse again soon. Radeon 6950 (MSI Frozr II), Seasonic X 560, Core i5 2500K at stock clockspeeds, 16GB RAM, Asus P8P67 M Pro

    Read the article

< Previous Page | 380 381 382 383 384 385 386 387 388 389 390 391  | Next Page >