Search Results

Search found 31621 results on 1265 pages for '13 10'.

Page 386/1265 | < Previous Page | 382 383 384 385 386 387 388 389 390 391 392 393  | Next Page >

• Public IP Routing over Private GRE tunnel

  - by Paul

  I have a GRE tunnel configured between two linux boxes. The tunnel works fine. I can ping from each host the other private ip. Head privateip: 10.0.0.1 publicip: 8.8.8.8 Tail privateip: 10.0.0.2 publicip: 7.7.7.7 The public IP on Tail has the network block 9.9.9.0/23 statically routed over the 7.7.7.7 interface. The idea is to make the 9.9.9.0/23 ips work on servers on the 8.8.8.8 network. I configure the tail host to route the /23 block. I mounted a 9.9 IP on the head server. I can ping the 9.9 ip from the tail to the head. I can't ping the 9.9 ip from the public internet. I think I need to add some other routes because of gateway issues, but I can't seem to wrap my mind around it (not a router guy, just beating my way through something that I have never done before and vaguely understand) --danks

  Read the article

• In DNS can an IN NS point to a CNAME?

  - by Mark Wagner

  Is it allowed to have an NS record be a CNAME? E.g.: subdomain.example.com. IN NS ns1.example.com. ns1.example.com. CNAME foo.example.com. foo.example.com. IN A 10.1.1.1 This doesn't seem to work in bind though this (of course) does: subdomain.example.com. IN NS foo.example.com. foo.example.com. IN A 10.1.1.1 Any pointers to RFCs prohibiting this setup would be appreciated.

  Read the article

• Can't manage iPod from linux anymore

  - by kemp

  I used to be able to see and manage my iPod with different softwares: Amarok, Rhythmbox, GTKPod. The device is a nano 1st generation 4gb. Currently it mounts regularly and can be accessed from the file system, but I get this in dmesg: [ 1547.617891] scsi 11:0:0:0: Direct-Access Apple iPod 1.62 PQ: 0 ANSI: 0 [ 1547.619103] sd 11:0:0:0: Attached scsi generic sg2 type 0 [ 1547.620478] sd 11:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 [ 1547.620494] sd 11:0:0:0: [sdb] 7999487 512-byte hardware sectors: (4.09 GB/3.81 GiB) [ 1547.621718] sd 11:0:0:0: [sdb] Write Protect is off [ 1547.621726] sd 11:0:0:0: [sdb] Mode Sense: 68 00 00 08 [ 1547.621732] sd 11:0:0:0: [sdb] Assuming drive cache: write through [ 1547.623591] sd 11:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 [ 1547.624993] sd 11:0:0:0: [sdb] Assuming drive cache: write through [ 1547.625003] sdb: sdb1 sdb2 [ 1547.629686] sd 11:0:0:0: [sdb] Attached SCSI removable disk [ 1548.084026] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 1548.369502] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 1548.504358] FAT: invalid media value (0x2f) [ 1548.504363] VFS: Can't find a valid FAT filesystem on dev sdb1. [ 1548.945173] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 1548.945179] FAT: invalid media value (0x2f) [ 1548.945182] VFS: Can't find a valid FAT filesystem on dev sdb1. [ 1610.092886] usb 2-6: USB disconnect, address 9 The only application that can access it (partially) is Rhythmbox. I say partially because I can transfer files to the iPod but can't remove or modify them. Also one transfer didn't finish and only 9 out of 16 songs were delivered to the device. All other softwares I tried (GTKPod, Amarok, Songbird) don't even detect it. What can I do to troubleshoot this? EDIT: # fdisk -l /dev/sdb Disk /dev/sdb: 4095 MB, 4095737344 bytes 241 heads, 62 sectors/track, 535 cylinders Units = cylinders of 14942 * 512 = 7650304 bytes Disk identifier: 0x20202020 Device Boot Start End Blocks Id System /dev/sdb1 1 11 80293+ 0 Empty Partition 1 has different physical/logical beginnings (non-Linux?): phys=(0, 1, 1) logical=(0, 1, 2) Partition 1 has different physical/logical endings: phys=(9, 254, 63) logical=(10, 181, 8) Partition 1 does not end on cylinder boundary. /dev/sdb2 11 536 3919415+ b W95 FAT32 Partition 2 has different physical/logical beginnings (non-Linux?): phys=(10, 0, 7) logical=(10, 181, 15) Partition 2 has different physical/logical endings: phys=(497, 240, 62) logical=(535, 88, 61) EDIT2: The "before" state is hard to tell, it was a lot of updates ago. Haven't been using my iPod for a while so I can't say when exactly it stopped working. I'm sure Amarok was still at version 1.X but can't remember when it was. My current system is debian testing fully updated. NOTE: just noticed that if I mount the device manually instead of letting nautilus automount it, I can see it again on GTKPod but still not on Banshee AND it's vanished from Rhythmbox...

  Read the article

• OpenVPN, Great on Windows, VERY slow on Mac...

  - by Phsion

  Hello, I'm not really an IT Pro, but this seemed like the best place to ask this question... I have setup VPN networks in the past, for fun, and everything was great, but now I've set one up for my boss, and while my computers all work great, his Mac machines are almost too slow to work with. Its pretty much vanilla configs all around, anyone have any ideas? Its a TUN routing setup over UDP. Back Story: My boss travels a lot, and wants to be able to access all his files from the road, and is also pretty paranoid about security (even though knows almost nothing about computers). SO i figured a VPN would be the answer. I went with OpenVPN, but there are some other issues. The only ISP we can get in our area besides Dial-UP is a crappy Satellite provider, that doesn't offer public IPs unless your willing to pay, so while the computers and VPN setup are pretty vanilla, the routing and structure is strange to get around this limitation. Specs: Its OpenVPN2, and there are six machines using it (only three actually use it, the rest are my test machines), one Windows 7 laptop, two XP Desktops, one OS X 10.5 Desktop, one 10.6 Desktop, and one 10.6 Laptop. One XP Desktop sits at my house and acts as the server (6Mbs/2Mbs FIOS connection). One XP desktop sits at the office and hosts a webpage that will wake up the Main Mac Desktop from sleep, and also ping all the machines on the VPN and show their status. The main office mac (10.6) stays in sleep mode until it gets the Wake-On-Lan packet from the Office XP, and then it auto connects to the VPN and opens itself up. The reason for all this is the Satellite private IP crap means i cant directly access the office machines outside of the LAN, so everyone connects to my house first, then they talk to each other from there. The Wake On Lan weirdness is because my boss doesn't want to leave the main Mac on all the time, and making a quick and dirty webpage was the easiest way to send a Magic Packet from inside the LAN without confusing my boss. The VPN uses Client Config files to make static IPs for the client. The only thing i found in google was some changes to the VPN MTU settings (down to 1400) but no real help. Oh, and i forgot...all the windows machines just have OpenVPN start as a service. The Mac laptop uses tunnelblick (an OpenVPN GUI) and the Mac Desktops use OpenVPN in normal command line mode. Server Config: tun-mtu 1500 fragment 1450 mssfix 1450 management localhost #### port #### proto udp dev tun ca ####### cert ####### key ###### dh ###### server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt client-config-dir ccd route 10.8.0.0 255.255.255.252 client-to-client keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status log Client Configs (all are simple variations on this) tun-mtu 1500 fragment 1450 mssfix 1450 client dev tun proto udp remote ######## #### resolv-retry infinite nobind persist-key presist-tun ca ##### cert ##### key ##### ns-cert-type server comp-lzo verb 3

  Read the article

• Can Acrobat 11 be made to do OCR using multiple CPU cores?

  - by tarcman.

  OCR processing takes time. Using multiple CPU cores would speed up processing. Acrobat 10 was not a multithreaded application. How about Acrobat 11? Does 11 by default do OCR using multiple CPU cores (if available)? If not, are there any workarounds, e.g. scripting, to help make Acrobat 11 do OCR using multiple CPU cores? Either through Acrobat's built in scripting language or using external scripts that launch and direct multiple single thread instances of Acrobat to in parallell to parts of the processing job. Note: This question is not too localized (not limited to a specific moment in time) because (1) Adobe does not release new major Acrobat versions very often (Acrobat 10 was released two years ago) and (2) Adobe Acrobat is a widely used application.

  Read the article

• FFmpeg audio dont work in converted videos

  - by Juddy Swaft

  NOTICE: when i convert videos via terminal and download them from ftp into pc the audio works fine. I use: if($ext == "avi" && $convert_avi == true) { $convert_source = _VIDEOS_DIR_PATH.$new_name; $conv_name = substr(md5($file['name'].rand(1,888)), 2, 10).".mp4"; $converted_file = _VIDEOS_DIR_PATH.$conv_name; $ffmpeg_command = 'ffmpeg -i '.$convert_source.' -acodec libmp3lame -vcodec libx264 -s 1280x720 -ar 44100 -async 44100 -r 29.970 -ac 2 -qscale 5 '.$converted_file; echo exec($ffmpeg_command); $sql = "UPDATE pm_temp SET url = '".$conv_name."' WHERE url = '".$new_name."' LIMIT 1"; $result = @mysql_query($sql); unlink($convert_source); } This code to convert avi to mp4 ffmpeg concole output: root@1tb:~# ffmpeg -i sample.avi -acodec libmp3lame -vcodec libx264 -s 1280x720 -ar 44100 -async 44100 -r 29.970 -ac 2 -qscale 5 goodsample.mp4 ffmpeg version 0.7.15, Copyright (c) 2000-2013 the FFmpeg developers built on Feb 22 2013 07:18:58 with gcc 4.4.5 configuration: --enable-libdc1394 --prefix=/usr --extra-cflags='-Wall -g ' --cc='ccache cc' --enable-shared --enable-libmp3lame --enable-gpl --enable-libvorbis --enable-pthreads --enable-libfaac --enable-libxvid --enable-postproc --enable-x11grab --enable-libgsm --enable-libtheora --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-libx264 --enable-libspeex --enable-nonfree --disable-stripping --enable-avfilter --enable-libdirac --disable-decoder=libdirac --enable-libfreetype --enable-libschroedinger --disable-encoder=libschroedinger - s libavutil 50. 43. 0 / 50. 43. 0 libavcodec 52.123. 0 / 52.123. 0 libavformat 52.111. 0 / 52.111. 0 libavdevice 52. 5. 0 / 52. 5. 0 libavfilter 1. 80. 0 / 1. 80. 0 libswscale 0. 14. 1 / 0. 14. 1 libpostproc 51. 2. 0 / 51. 2. 0 [mp3 @ 0x191d4100] Header missing [mpeg4 @ 0x191d1dc0] Invalid and inefficient vfw-avi packed B frames detected Input #0, avi, from 'sample.avi': Metadata: encoder : VirtualDubMod 1.5.10.2 (build 2540/release) Duration: 00:01:01.81, start: 0.000000, bitrate: 1194 kb/s Stream #0.0: Video: mpeg4, yuv420p, 640x352 [PAR 1:1 DAR 20:11], 23.98 tbr, Stream #0.1: Audio: mp3, 48000 Hz, stereo, s16, 128 kb/s [buffer @ 0x191d1c80] w:640 h:352 pixfmt:yuv420p tb:1/1000000 sar:1/1 sws_param: [scale @ 0x191d6880] w:640 h:352 fmt:yuv420p -> w:1280 h:720 fmt:yuv420p flags:0 [libx264 @ 0x191ce5a0] Default settings detected, using medium profile [libx264 @ 0x191ce5a0] using SAR=45/44 [libx264 @ 0x191ce5a0] using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle S [libx264 @ 0x191ce5a0] profile High, level 3.1 [libx264 @ 0x191ce5a0] 264 - core 118 - H.264/MPEG-4 AVC codec - Copyleft 2003-2 6 chroma_me=1 trellis=1 8x8dct=1 cqm=0 deadzone=21,11 fast_pskip=1 chroma_qp_off 1 open_gop=0 weightp=2 keyint=250 keyint_min=25 scenecut=40 intra_refresh=0 rc_l Output #0, mp4, to 'goodsample.mp4': Metadata: encoder : Lavf52.111.0 Stream #0.0: Video: libx264, yuv420p, 1280x720 [PAR 45:44 DAR 20:11], q=2-31 Stream #0.1: Audio: libmp3lame, 44100 Hz, stereo, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop, [?] for help [mp3 @ 0x191d4100] Header missing Error while decoding stream #0.1 [mpeg4 @ 0x191d1dc0] Invalid and inefficient vfw-avi packed B frames detected [mp3 @ 0x191d4100] incomplete frame 9467kB time=00:01:00.32 bitrate=1285.5kbits/ Error while decoding stream #0.1 frame= 1852 fps= 20 q=29.0 Lsize= 9652kB time=00:01:01.72 bitrate=1280.9kbits video:9121kB audio:483kB global headers:0kB muxing overhead 0.499688% frame I:11 Avg QP:16.78 size: 51456 [libx264 @ 0x191ce5a0] frame P:784 Avg QP:20.81 size: 8954 [libx264 @ 0x191ce5a0] frame B:1057 Avg QP:26.06 size: 1659 [libx264 @ 0x191ce5a0] consecutive B-frames: 22.0% 3.1% 7.5% 67.4% [libx264 @ 0x191ce5a0] mb I I16..4: 31.1% 59.8% 9.1% [libx264 @ 0x191ce5a0] mb P I16..4: 1.8% 2.6% 0.2% P16..4: 24.3% 7.0% 4.0 [libx264 @ 0x191ce5a0] mb B I16..4: 0.1% 0.1% 0.0% B16..8: 22.7% 0.8% 0.2 [libx264 @ 0x191ce5a0] 8x8 transform intra:57.0% inter:72.6% [libx264 @ 0x191ce5a0] coded y,uvDC,uvAC intra: 44.4% 33.3% 10.3% inter: 7.6% 5. [libx264 @ 0x191ce5a0] i16 v,h,dc,p: 68% 14% 8% 10% [libx264 @ 0x191ce5a0] i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 21% 14% 27% 5% 7% 7% 6 [libx264 @ 0x191ce5a0] i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 28% 14% 14% 6% 10% 9% 7 [libx264 @ 0x191ce5a0] i8c dc,h,v,p: 67% 13% 17% 3% [libx264 @ 0x191ce5a0] Weighted P-Frames: Y:1.9% UV:0.4% [libx264 @ 0x191ce5a0] ref P L0: 62.2% 12.8% 10.3% 14.5% 0.2% [libx264 @ 0x191ce5a0] ref B L0: 88.1% 5.5% 6.4% [libx264 @ 0x191ce5a0] ref B L1: 95.7% 4.3% [libx264 @ 0x191ce5a0] kb/s:1209.03 I know there is couple errors tough, but i dont know hot to fix it. Also i would be very thankfull if someone can help reduce video size but is not main problem video weights as original avi but sill.

  Read the article

• tar incremental backup is backing everything up, every time when used on the Dropbox directory

  - by Cyclic

  I made an incremental backup about 10 months ago (on Jan 27, 2013), creating a .snar metadata file. Now, when I try to make an incremental backup using tar --create --file=dropbox_incremental_1.tar --listed-incremental=dropbox_0.snar Dropbox the command just re-backs up everything. I'm not an expert at Unix timestamps, but I noticed that virtually all of my directory timestamps are way more recent than the last time they changed. For my actual files, they look like this: Access: 2013-03-12 19:04:51.000000000 -0500 Modify: 2012-09-30 15:10:47.000000000 -0500 Change: 2013-03-12 19:04:51.306209672 -0500 The 'Modify' timestamp seems correct, but the files were definitely not changed (at least not doing anything that I know of) at the time they say they were. These files still seem to go into the incremental archive. What's happening here? Is there a way to tell tar to look at the 'modify' timestamp? Isn't this what it's supposed to be doing?

  Read the article

• Apache/Jboss Issue - is this connection timeout?

  - by user115391

  We have an application. The architecture is as below 1 load balancer (apache), which redirects to 2 app servers (jboss). The site is working fine and I am able to access it fine. But sometimes, randomly the homepage takes a while (like 30-40 secs) to load. I tried checking the logs but could not figure out why. I used the httptraffic analyzer, fiddler to see the traffic, but it just says the request/response took 30 secs or so. I checked the apache access logs, mod_jk.log. My configurations are below mod-jk.conf LoadModule jk_module modules/mod_jk.so JkWorkersFile conf/workers.properties JkLogFile logs/mod_jk.log #JkLogLevel info #JkLogLevel debug JkLogLevel error # Select the log format JkLogStampFormat "[%a %b %d %H:%M:%S %Y]" JkOptions +ForwardKeySize +ForwardURICompatUnparsed -ForwardDirectories JkRequestLogFormat "%w %V %T %P %{tid}P %D" JkMount /__application__/* loadbalancer JkUnMount /__application__/images/* loadbalancer <VirtualHost *:8080 > JkMountFile conf/uriworkermap.properties </VirtualHost> JkShmFile run/jk.shm <Location /jkstatus> JkMount status Order deny,allow Deny from all Allow from 127.0.0.1 </Location> ----------------------------- uriworkermap.properties Simple worker configuration file # Mount the Servlet context to the ajp13 worker /=loadbalancer /*=loadbalancer ----------------------------- workers.properties worker.list=loadbalancer,status worker.template.port=8009 worker.template.type=ajp13 worker.template.lbfactor=1 worker.template.prepost_timeout=10000 worker.template.connect_timeout=10000 worker.template.ping_mode=A worker.worker1.reference=worker.template worker.worker1.host=hostname1 worker.worker2.reference=worker.template worker.worker2.host=hostname2 worker.loadbalancer.type=lb worker.loadbalancer.balance_workers=worker1,worker2 worker.status.type=status ----------------------------- my jboss server.xml - $JBOSS_HOME/server/default/deploy/jbossweb.sar/server.xml --------------------------------- The logs from access log is below The issue where it took time - look at the seconds column [23/Mar/2012:12:10:38 -0400] "GET / HTTP/1.1" 200 138 x.x.x.x - - [23/Mar/2012:12:10:49 -0400] "GET /index.jsp HTTP/1.1" 302 - x.x.x.x - - [23/Mar/2012:12:11:10 -0400] "GET /home.jsp HTTP/1.1" 200 936 x.x.x.x - - [23/Mar/2012:12:11:31 -0400] "POST /login/ HTTP/1.1" 200 8895 x.x.x.x - - [23/Mar/2012:12:11:52 -0400] "GET /login/includes/login-style.css HTTP/1.1" 304 - The one after the issue x.x.x.x - - [23/Mar/2012:12:12:18 -0400] "GET / HTTP/1.1" 200 138 x.x.x.x - - [23/Mar/2012:12:12:18 -0400] "GET /index.jsp HTTP/1.1" 302 - x.x.x.x - - [23/Mar/2012:12:12:18 -0400] "GET /home.jsp HTTP/1.1" 200 936 x.x.x.x - - [23/Mar/2012:12:12:18 -0400] "POST /login/ HTTP/1.1" 200 8895 x.x.x.x - - [23/Mar/2012:12:12:18 -0400] "GET /login/includes/login-style.css HTTP/1.1" 304 - Would it be a cache or timeout issue? Any help is appreciated. Thanks.

  Read the article

• Solaris10 x86 mirror. Making second disk booteable when failure

  - by Kani

  Did a mirror (RAID1) with Solaris 10 in x86. Everything OK. Now, I´m trying to make the second disk booteable, this is: from grub or in case of failure of disk1. I edited /boot/grub/menu.lst: #---------- ADDED BY BOOTADM - DO NOT EDIT ---------- title Solaris 10 9/10 s10x_u9wos_14a X86 findroot (rootfs1,0,a) kernel /platform/i86pc/multiboot module /platform/i86pc/boot_archive #---------------------END BOOTADM-------------------- #---------- ADDED BY BOOTADM - DO NOT EDIT ---------- title Solaris failsafe findroot (rootfs1,0,a) kernel /boot/multiboot -s module /boot/amd64/x86.miniroot-safe #---------------------END BOOTADM-------------------- #---------- ADDED BY BOOTADM - DO NOT EDIT ---------- title Solaris failsafe findroot (rootfs1,0,a) kernel /boot/multiboot kernel/unix -s module /boot/x86.miniroot-safe #---------------------END BOOTADM-------------------- #Make second disk booteable!!!!!!! title alternate boot findroot (rootfs1,1,a) kernel /boot/multiboot kernel/unix -s module /boot/x86.miniroot-safe But is not working. In the BIOS, when I select "alternate boot" I get: Error 15: 15 file not found also, how to configure to GRUB to make the disk2 to boot in case of error in disk1? Additionally, I did (but not related to GRUB): eeprom altbootpath=/devices/pci@0,0/pci108e,5352@1f,2/disk@1,0:a Here is the output of some commands that may help you: /sbin/biosdev 0x80 /pci@0,0/pci108e,5352@1f,2/disk@0,0 0x81 /pci@0,0/pci108e,5352@1f,2/disk@1,0 ls -l /dev/dsk/c1t?d0s0 lrwxrwxrwx 1 root root 50 Jul 7 12:01 /dev/dsk/c1t0d0s0 -> ../../devices/pci@0,0/pci108e,5352@1f,2/disk@0,0:a lrwxrwxrwx 1 root root 50 Jul 7 12:01 /dev/dsk/c1t1d0s0 -> ../../devices/pci@0,0/pci108e,5352@1f,2/disk@1,0:a more /boot/solaris/bootenv.rc setprop ata-dma-enabled '1' setprop atapi-cd-dma-enabled '0' setprop ttyb-rts-dtr-off 'false' setprop ttyb-ignore-cd 'true' setprop ttya-rts-dtr-off 'false' setprop ttya-ignore-cd 'true' setprop ttyb-mode '9600,8,n,1,-' setprop ttya-mode '9600,8,n,1,-' setprop lba-access-ok '1' setprop prealloc-chunk-size '0x2000' setprop bootpath '/pci@0,0/pci108e,5352@1f,2/disk@0,0:a' setprop keyboard-layout 'US-English' setprop console 'text' setprop altbootpath '/pci@0,0/pci108e,5352@1f,2/disk@1,0:a' cat /etc/vfstab #device device mount FS fsck mount mount #to mount to fsck point type pass at boot options # fd - /dev/fd fd - no - /proc - /proc proc - no - #/dev/dsk/c1t0d0s1 - - swap - no - /dev/md/dsk/d1 - - swap - no - /dev/md/dsk/d0 /dev/md/rdsk/d0 / ufs 1 no - /devices - /devices devfs - no - sharefs - /etc/dfs/sharetab sharefs - no - ctfs - /system/contract ctfs - no - objfs - /system/object objfs - no - swap - /tmp tmpfs - yes - df -h Filesystem size used avail capacity Mounted on /dev/md/dsk/d0 909G 11G 889G 2% / /devices 0K 0K 0K 0% /devices ctfs 0K 0K 0K 0% /system/contract proc 0K 0K 0K 0% /proc mnttab 0K 0K 0K 0% /etc/mnttab swap 14G 972K 14G 1% /etc/svc/volatile objfs 0K 0K 0K 0% /system/object sharefs 0K 0K 0K 0% /etc/dfs/sharetab /usr/lib/libc/libc_hwcap1.so.1 909G 11G 889G 2% /lib/libc.so.1 fd 0K 0K 0K 0% /dev/fd swap 14G 40K 14G 1% /tmp swap 14G 28K 14G 1% /var/run

  Read the article

• Redhat with a reverse proxy, a specific configuration

  - by jessica

  The setup I am trying to put together consists on a server connected to the internet (a redhat box) and 2 Apache Tomcat boxes not connected to the internet. Let's call the server Server and the two Apache Tomcats, Apache1 and Apache2. So, assuming my external IP is 102.1.1.1, Apache1 is 10.1.1.1 and Apache2 is 10.1.1.2, what I'm trying to configure is a reverse proxy so that if the request goes into http://102.1.1.1/mywebserver1/ it will be directed to Apache1 and if the request goes into http://102.1.1.1/mywebserver2/ it will be forwarded to Apache2. Now, I don't need a cache on the proxy since there is application sitting in those tomcats and each request needs to get a fresh answer. I searched for a while and I tried building this with Squid but i can't get it to work the way I need it. Anyone knows how to do this? What software do I need? How do I configure the reverse proxy? Thanks! jessica

  Read the article

• rdiff-backup is taking longer and longer every time it runs

  - by Jakobud

  I've been running rdiff-backup for the past week or so, every night at 4am. It started out not taking that long, but its taking longer and longer and longer every time its runs every night. In some cases there are quite a few new and changed files and in other cases, not so much. It started out taking < 10 minutes, and after a week its taking over 4.5 hrs to run. Take a look at my session stats below: StartTime 1268046002.00 (Mon Mar 8 04:00:02 2010) EndTime 1268046373.50 (Mon Mar 8 04:06:13 2010) ElapsedTime 371.50 (6 minutes 11.50 seconds) SourceFiles 213928 SourceFileSize 277271282225 (258 GB) MirrorFiles 213914 MirrorFileSize 276693097638 (258 GB) NewFiles 16 NewFileSize 578209911 (551 MB) DeletedFiles 2 DeletedFileSize 2598 (2.54 KB) ChangedFiles 27 ChangedSourceSize 5195150 (4.95 MB) ChangedMirrorSize 5217876 (4.98 MB) IncrementFiles 0 IncrementFileSize 0 (0 bytes) TotalDestinationSizeChange 578184587 (551 MB) Errors 0 StartTime 1268132402.00 (Tue Mar 9 04:00:02 2010) EndTime 1268134341.29 (Tue Mar 9 04:32:21 2010) ElapsedTime 1939.29 (32 minutes 19.29 seconds) SourceFiles 213963 SourceFileSize 307959842562 (287 GB) MirrorFiles 213928 MirrorFileSize 277271282225 (258 GB) NewFiles 37 NewFileSize 31265005547 (29.1 GB) DeletedFiles 2 DeletedFileSize 576511960 (550 MB) ChangedFiles 25 ChangedSourceSize 5243761 (5.00 MB) ChangedMirrorSize 5177011 (4.94 MB) IncrementFiles 65 IncrementFileSize 577266412 (551 MB) TotalDestinationSizeChange 31265826749 (29.1 GB) Errors 0 StartTime 1268218802.00 (Wed Mar 10 04:00:02 2010) EndTime 1268225230.15 (Wed Mar 10 05:47:10 2010) ElapsedTime 6428.15 (1 hour 47 minutes 8.15 seconds) SourceFiles 213971 SourceFileSize 307960643843 (287 GB) MirrorFiles 213963 MirrorFileSize 307959842562 (287 GB) NewFiles 9 NewFileSize 694087 (678 KB) DeletedFiles 1 DeletedFileSize 894 (894 bytes) ChangedFiles 38 ChangedSourceSize 30656167797 (28.6 GB) ChangedMirrorSize 30656059709 (28.6 GB) IncrementFiles 48 IncrementFileSize 289278151 (276 MB) TotalDestinationSizeChange 290079432 (277 MB) Errors 0 StartTime 1268305202.00 (Thu Mar 11 04:00:02 2010) EndTime 1268312788.15 (Thu Mar 11 06:06:28 2010) ElapsedTime 7586.15 (2 hours 6 minutes 26.15 seconds) SourceFiles 213971 SourceFileSize 307960643779 (287 GB) MirrorFiles 213971 MirrorFileSize 307960643843 (287 GB) NewFiles 0 NewFileSize 0 (0 bytes) DeletedFiles 0 DeletedFileSize 0 (0 bytes) ChangedFiles 15 ChangedSourceSize 30650824127 (28.5 GB) ChangedMirrorSize 30650824191 (28.5 GB) IncrementFiles 16 IncrementFileSize 689437042 (657 MB) TotalDestinationSizeChange 689436978 (657 MB) Errors 0 StartTime 1268391601.00 (Fri Mar 12 04:00:01 2010) EndTime 1268400145.85 (Fri Mar 12 06:22:25 2010) ElapsedTime 8544.85 (2 hours 22 minutes 24.85 seconds) SourceFiles 213974 SourceFileSize 307960784445 (287 GB) MirrorFiles 213971 MirrorFileSize 307960643779 (287 GB) NewFiles 5 NewFileSize 269587 (263 KB) DeletedFiles 2 DeletedFileSize 128921 (126 KB) ChangedFiles 16 ChangedSourceSize 30650815948 (28.5 GB) ChangedMirrorSize 30650815948 (28.5 GB) IncrementFiles 26 IncrementFileSize 818279963 (780 MB) TotalDestinationSizeChange 818420629 (781 MB) Errors 0 StartTime 1268478002.00 (Sat Mar 13 04:00:02 2010) EndTime 1268488740.33 (Sat Mar 13 06:59:00 2010) ElapsedTime 10738.33 (2 hours 58 minutes 58.33 seconds) SourceFiles 213974 SourceFileSize 307960784238 (287 GB) MirrorFiles 213974 MirrorFileSize 307960784445 (287 GB) NewFiles 0 NewFileSize 0 (0 bytes) DeletedFiles 0 DeletedFileSize 0 (0 bytes) ChangedFiles 16 ChangedSourceSize 30650823920 (28.5 GB) ChangedMirrorSize 30650824127 (28.5 GB) IncrementFiles 19 IncrementFileSize 1041846015 (994 MB) TotalDestinationSizeChange 1041845808 (994 MB) Errors 0 StartTime 1268560803.00 (Sun Mar 14 04:00:03 2010) EndTime 1268573194.82 (Sun Mar 14 07:26:34 2010) ElapsedTime 12391.82 (3 hours 26 minutes 31.82 seconds) SourceFiles 213974 SourceFileSize 307960784238 (287 GB) MirrorFiles 213974 MirrorFileSize 307960784238 (287 GB) NewFiles 0 NewFileSize 0 (0 bytes) DeletedFiles 0 DeletedFileSize 0 (0 bytes) ChangedFiles 14 ChangedSourceSize 30650815948 (28.5 GB) ChangedMirrorSize 30650815948 (28.5 GB) IncrementFiles 15 IncrementFileSize 1116911810 (1.04 GB) TotalDestinationSizeChange 1116911810 (1.04 GB) Errors 0 StartTime 1268647203.00 (Mon Mar 15 04:00:03 2010) EndTime 1268662364.88 (Mon Mar 15 08:12:44 2010) ElapsedTime 15161.88 (4 hours 12 minutes 41.88 seconds) SourceFiles 214010 SourceFileSize 307963430178 (287 GB) MirrorFiles 213974 MirrorFileSize 307960784238 (287 GB) NewFiles 37 NewFileSize 2684172 (2.56 MB) DeletedFiles 1 DeletedFileSize 5348 (5.22 KB) ChangedFiles 32 ChangedSourceSize 30656134913 (28.6 GB) ChangedMirrorSize 30656167797 (28.6 GB) IncrementFiles 71 IncrementFileSize 1316460362 (1.23 GB) TotalDestinationSizeChange 1319106302 (1.23 GB) Errors 0 StartTime 1268733603.00 (Tue Mar 16 04:00:03 2010) EndTime 1268750396.76 (Tue Mar 16 08:39:56 2010) ElapsedTime 16793.76 (4 hours 39 minutes 53.76 seconds) SourceFiles 214010 SourceFileSize 307963430156 (287 GB) MirrorFiles 214010 MirrorFileSize 307963430178 (287 GB) NewFiles 0 NewFileSize 0 (0 bytes) DeletedFiles 0 DeletedFileSize 0 (0 bytes) ChangedFiles 15 ChangedSourceSize 30650823898 (28.5 GB) ChangedMirrorSize 30650823920 (28.5 GB) IncrementFiles 16 IncrementFileSize 936032413 (893 MB) TotalDestinationSizeChange 936032391 (893 MB) Errors 0 StartTime 1268820002.00 (Wed Mar 17 04:00:02 2010) EndTime 1268834619.90 (Wed Mar 17 08:03:39 2010) ElapsedTime 14617.90 (4 hours 3 minutes 37.90 seconds) SourceFiles 214010 SourceFileSize 307963430156 (287 GB) MirrorFiles 214010 MirrorFileSize 307963430156 (287 GB) NewFiles 0 NewFileSize 0 (0 bytes) DeletedFiles 0 DeletedFileSize 0 (0 bytes) ChangedFiles 14 ChangedSourceSize 30650815948 (28.5 GB) ChangedMirrorSize 30650815948 (28.5 GB) IncrementFiles 15 IncrementFileSize 1289272860 (1.20 GB) TotalDestinationSizeChange 1289272860 (1.20 GB) Errors 0 Is this common behavior? It's only about 300gigs of data total. One important thing to note though, rdiff-backup is backup up stuff over to a USB2 external drive. Maybe thats why its so slow?

  Read the article

• How to restore missing space in NTFS file systems

  - by jacobsee

  I have a 40 GB USB hard drive formatted with NTFS on a PC running Windows XP Pro, SP3. I am trying to free as much space as possible. Windows Explorer tells me that I have about 200 MB of files on the drive (showing hidden and system files). When I show drive properties however it shows 73% free, around 10 GB used. I ran CHKDSK and it found all kinds of problems. Now running defrag and it is behaving as if there were 10 GB of files, but I can't access them anywhere. How to find and remove this extra 10GB?

  Read the article

• Bash Script Exits su or ssh Session Rather than Script

  - by Russ

  I am using CentOS 5.4. I created a bash script that does some checking before running any commands. If the check fails, it will simply exit 0. The problem I am having is that on our server, the script will exit the su or ssh session when the exit 0 is called. #!/bin/bash # check if directory has contents and exit if none if [ -z "`ls /ebs_raid/import/*.txt 2>/dev/null`" ]; then echo "ok" exit 0 fi here is the output: [root@ip-10-251-86-31 ebs_raid]# . test.sh ok [russ@ip-10-251-86-31 ebs_raid]$ as you can see, I was removed from my sudo session, if I wasn't in the sudo session, it would have logged me out of my ssh session. I am not sure what I am doing wrong here or where to start.

  Read the article

• Using VLANs that are routed together?

  - by dannymcc

  I have a quick question that's bugging me the more I read about VLANs. So far I understand that they are useful for dividing the network into sub-sections, but if you route them together does that not remove any security benefit? As an example, if I created a VLAN on my home network which was simply one computer, one server and one router.if I wanted to divide the network between computers and servers I could put the computer on VLAN 10 and the server on VLAN 20. Then the computer would no longer be able to communicate with the server - unless I added a static route to the router that connected the two together, basically telling VLAN 10 that VLAN 20 exists and how to communicate with it. The VLANs would then be connected in a similar way to a 'flat' network that has no VLANs. Therefore, surely, all security benefits are lost. Am I missing something?

  Read the article

• Ping isn't acting accurate?

  - by Earlz

  I've been trying to diagnose some latency issues with my internet connection. I've been lagging out of online video games and such, which of course could be their server's fault. So, I've been running ping some. It doesn't indicate anything unusual, but it does act a bit strange. I can start it with something like ping internethost -i 0.1 so that it will send a ton of packets, and every 10-20 seconds it will appear to just freeze for 2 or 3 seconds. The packets are still being received in the right order though, and there is no packet loss. The weirdest thing is that after the little freeze up, it will usually just report a ping time that is about 10-30ms higher than the average. How does this happen? Is ping still being accurate? I'm using Arch Linux. The host I'm pinging is my website, which shouldn't be doing any kind of ping slowing or filtering.

  Read the article

• PHP Mail() to Gmail = Spam

  - by grantw

  Recently Gmail has started marking emails sent directly from my server (using php mail()) as spam and I'm having problems trying to find the issue. If I send an exact copy of the same email from my email client it goes to the Gmail inbox. The emails are plain text, around 7 lines long and contain a URL link in plain text. As the emails sent from my client are getting through fine I'm thinking that the content isn't the issue. It would be greatly appreciated if someone could take a look at the the following headers and give me some advice why the email from the server is being marked as spam. Email from Server: Delivered-To: [email protected] Received: by 10.49.98.228 with SMTP id el4csp101784qeb; Thu, 15 Nov 2012 14:58:52 -0800 (PST) Received: by 10.60.27.166 with SMTP id u6mr2296595oeg.86.1353020331940; Thu, 15 Nov 2012 14:58:51 -0800 (PST) Return-Path: [email protected] Received: from dom.domainbrokerage.co.uk (dom.domainbrokerage.co.uk. [174.120.246.138]) by mx.google.com with ESMTPS id df4si17005013obc.50.2012.11.15.14.58.51 (version=TLSv1/SSLv3 cipher=OTHER); Thu, 15 Nov 2012 14:58:51 -0800 (PST) Received-SPF: pass (google.com: domain of [email protected] designates 174.120.246.138 as permitted sender) client-ip=174.120.246.138; Authentication-Results: mx.google.com; spf=pass (google.com: domain of [email protected] designates 174.120.246.138 as permitted sender) [email protected]; dkim=pass [email protected] DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; d=domainbrokerage.co.uk; s=default; h=Date:Message-Id:Content-Type:Reply-to:From:Subject:To; bh=2RJ9jsEaGcdcgJ1HMJgQG8QNvWevySWXIFRDqdY7EAM=; b=mGebBVOkyUhv94ONL3EabXeTgVznsT1VAwPdVvpOGDdjBtN1FabnuFi8sWbf5KEg5BUJ/h8fQ+9/2nrj+jbtoVLvKXI6L53HOXPjl7atCX9e41GkrOTAPw5ZFp+1lDbZ; Received: from grantw by dom.domainbrokerage.co.uk with local (Exim 4.80) (envelope-from [email protected]) id 1TZ8OZ-0008qC-Gy for [email protected]; Thu, 15 Nov 2012 22:58:51 +0000 To: [email protected] Subject: Offer Accepted X-PHP-Script: www.domainbrokerage.co.uk/admin.php for 95.172.231.27 From: My Name [email protected] Reply-to: [email protected] Content-Type: text/plain; charset=Windows-1251 Message-Id: [email protected] Date: Thu, 15 Nov 2012 22:58:51 +0000 X-AntiAbuse: This header was added to track abuse, please include it with any abuse report X-AntiAbuse: Primary Hostname - dom.domainbrokerage.co.uk X-AntiAbuse: Original Domain - gmail.com X-AntiAbuse: Originator/Caller UID/GID - [500 500] / [47 12] X-AntiAbuse: Sender Address Domain - domainbrokerage.co.uk X-Get-Message-Sender-Via: dom.domainbrokerage.co.uk: authenticated_id: grantw/from_h Email from client: Delivered-To: [email protected] Received: by 10.49.98.228 with SMTP id el4csp101495qeb; Thu, 15 Nov 2012 14:54:49 -0800 (PST) Received: by 10.182.197.8 with SMTP id iq8mr2351185obc.66.1353020089244; Thu, 15 Nov 2012 14:54:49 -0800 (PST) Return-Path: [email protected] Received: from dom.domainbrokerage.co.uk (dom.domainbrokerage.co.uk. [174.120.246.138]) by mx.google.com with ESMTPS id ab5si17000486obc.44.2012.11.15.14.54.48 (version=TLSv1/SSLv3 cipher=OTHER); Thu, 15 Nov 2012 14:54:49 -0800 (PST) Received-SPF: pass (google.com: domain of [email protected] designates 174.120.246.138 as permitted sender) client-ip=174.120.246.138; Authentication-Results: mx.google.com; spf=pass (google.com: domain of [email protected] designates 174.120.246.138 as permitted sender) [email protected]; dkim=pass [email protected] DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; d=domainbrokerage.co.uk; s=default; h=Content-Transfer-Encoding:Content-Type:Subject:To:MIME-Version:From:Date:Message-ID; bh=bKNjm+yTFZQ7HUjO3lKPp9HosUBfFxv9+oqV+NuIkdU=; b=j0T2XNBuENSFG85QWeRdJ2MUgW2BvGROBNL3zvjwOLoFeyHRU3B4M+lt6m1X+OLHfJJqcoR0+GS9p/TWn4jylKCF13xozAOc6ewZ3/4Xj/YUDXuHkzmCMiNxVcGETD7l; Received: from w-27.cust-7941.ip.static.uno.uk.net ([95.172.231.27]:1450 helo=[127.0.0.1]) by dom.domainbrokerage.co.uk with esmtpa (Exim 4.80) (envelope-from [email protected]) id 1TZ8Ke-0001XH-7p for [email protected]; Thu, 15 Nov 2012 22:54:48 +0000 Message-ID: [email protected] Date: Thu, 15 Nov 2012 22:54:50 +0000 From: My Name [email protected] User-Agent: Postbox 3.0.6 (Windows/20121031) MIME-Version: 1.0 To: [email protected] Subject: Offer Accepted Content-Type: text/plain; charset=ISO-8859-1; format=flowed Content-Transfer-Encoding: 7bit X-AntiAbuse: This header was added to track abuse, please include it with any abuse report X-AntiAbuse: Primary Hostname - dom.domainbrokerage.co.uk X-AntiAbuse: Original Domain - gmail.com X-AntiAbuse: Originator/Caller UID/GID - [47 12] / [47 12] X-AntiAbuse: Sender Address Domain - domainbrokerage.co.uk X-Get-Message-Sender-Via: dom.domainbrokerage.co.uk: authenticated_id: [email protected]

  Read the article

• Using OpenVPN, yet netflix.com blocks access

  - by user837848

  I have set up an OpenVPN server on a VPS in the USA and configured it to route all clients traffic through it. Everything seems to work fine regarding the VPN connection in gerneral. All ip lookup sites show me the us server's ip address and even hulu.com works(it won't work if you are not in the usa). But for some reason netflix.com says "Sorry, Netflix is not available in your country yet.". So I thought that netflix probably uses some more sophisticated ways to determine your location beyond just your ip address. But I could not find a way to get it to work until I dropped the idea of using a VPN and instead connected to the server via a simple socks tunnel with ssh by running: ssh -D 9999 user@serverip All I had to do was changing the key network.proxy.socks_remote_dns in Firefox from false to true to prevent DNS leaks and setting up the socks proxy. Then I could finally watch netflix.com. As a result I concluded that there is nothing in the browser(or something like system timezone) that tells netflix the location, so it has to have something to do with the OpenVPN config. After that I used tcpdump to log all the traffic on the server's network interface venet0 (OpenVZ VPS), visited netflix.com on the client while first connected to the VPN and then connected via socks tunnel and afterwards compared both outputs. The only thing that caught my eye was that while using the socks tunnel the server mainly used ipv6 to connect to netflix whereas it only used ipv4 when the client was connected to the OpenVPN server. But I don't get how that could make such a difference. So what am I missing? Is there a way to configure OpenVPN to also use ipv6 to connect to a website although there is only an ipv4 connection between the VPS and the client? Here is the server.conf of the OpenVPN server (OpenVZ VPS) local serverip port 443 proto tcp dev tun ca ./easy-rsa2/keys/ca.crt cert ./easy-rsa2/keys/vps1.crt key ./easy-rsa2/keys/vps1.key # This file should be kept secret dh ./easy-rsa2/keys/dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" client-to-client keepalive 10 120 tls-auth ta.key 0 # This file is secret cipher AES-256-CBC comp-lzo max-clients 4 user nobody group nogroup persist-key persist-tun status openvpn-status.log log-append openvpn.log verb 3 iptables forwarding iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o venet0 -j SNAT --to-source serverip (enabled ipv4 forwarding) I have tried everything always on a Win7 and a Debian client with only ipv4 connections and always made sure that they use the correct DNS server (tested with ipleak.net and tcpdump / wireshark). client.conf: client dev tun proto tcp remote serverip 443 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client.crt key client.key ns-cert-type server tls-auth ta.key 1 cipher AES-256-CBC comb-lzo verb 3

  Read the article

• Why are emails sent from my applications being marked as spam?

  - by Brian

  Hi. I have 2 web apps running on the same server. The first is www.nimikri.com and the other is www.hourjar.com. Both apps share the same IP address (75.127.100.175). My server is through a shared hosting company. I've been testing my apps, and at first all my emails were being delivered to me just fine. Then a few days ago every email from both apps got dumped into my spam box (in gmail and google apps). So far the apps have just been sending emails to me and nobody else, so I know people aren't manually flagging them as spam. I did a reverse DNS lookup for my IP and the results I got were these: 100.127.75.in-addr.arpa NS DNS2.GNAX.NET. 100.127.75.in-addr.arpa NS DNS1.GNAX.NET. Should the reverse DNS lookup point to nimikri.com and hourjar.com, or are they set up fine the way they are? I noticed in the email header these 2 lines: Received: from nimikri.nimikri.com From: Hour Jar <[email protected]> Would the different domain names be causing gmail to think this is spam? Here is the header from one of the emails. Please let me know if any of this looks like a red flag for spam. Thanks. Delivered-To: [email protected] Received: by 10.231.157.85 with SMTP id a21cs54749ibx; Sun, 25 Apr 2010 10:03:14 -0700 (PDT) Received: by 10.151.130.18 with SMTP id h18mr3056714ybn.186.1272214992196; Sun, 25 Apr 2010 10:03:12 -0700 (PDT) Return-Path: <[email protected]> Received: from nimikri.nimikri.com ([75.127.100.175]) by mx.google.com with ESMTP id 28si4358025gxk.44.2010.04.25.10.03.11; Sun, 25 Apr 2010 10:03:11 -0700 (PDT) Received-SPF: neutral (google.com: 75.127.100.175 is neither permitted nor denied by best guess record for domain of [email protected]) client-ip=75.127.100.175; Authentication-Results: mx.google.com; spf=neutral (google.com: 75.127.100.175 is neither permitted nor denied by best guess record for domain of [email protected]) [email protected] Received: from nimikri.nimikri.com (localhost.localdomain [127.0.0.1]) by nimikri.nimikri.com (8.14.3/8.14.3) with ESMTP id o3PH3A7a029986 for <[email protected]>; Sun, 25 Apr 2010 12:03:11 -0500 Date: Sun, 25 Apr 2010 12:03:10 -0500 From: Hour Jar <[email protected]> To: [email protected] Message-ID: <[email protected]> Subject: [email protected] has invited you to New Event MIME-Version: 1.0 Content-Type: text/html; charset=us-ascii Content-Transfer-Encoding: 7bit

  Read the article

• Wireless router blocking some sites while using ethernet is fine

  - by Micke

  I'm using Windows 7 and my router is a wireless Apple Airport Express that is approximately two years old. Suddenly I can't access some sites (for example www.sthlm.friskissvettis.se, or www.vegetarian-shoes.co.uk, some streamed tv-shows on svtplay.se, and a number of other random sites) when connecting to internet with my router. It worked good until recently and I'm fairly sure this problem emerged when my ISP upgraded from 10/10mbit to 100/10mbit speed. Most other sites like facebook and google works fine. When using my network cable to connect to internet everything works fine and I can access these sites. Firmware is current and I've tried reseting the router to factory defaults. Tried different browsers, and I can't ping the "blocked" sites either. Tracert www.sthlm.friskissvettis.se starts with 10.0.0.1 and continues through a number of long addresses until it says timeout. The last working address before timeout was sth-tcy-ipcore01-ge-0-2-0.neq.dgcsystems.net [83.241.252.13], if it matters. Tracert www.vegetarian-shoes.co.uk also eventually gives me a timeout. When the network cable is plugged in, I still get timeout on tracert www.sthlm.friskissvettis.se even though I can access the site in Chrome. Weird. www.vegetarian-shoes.co.uk doesn't give me a tracert timeout when the cable is plugged in, and I can access the site as usual. I've tried changing DNS servers to use opendns servers instead, but to no use. I've tried pinging these two sites with a lower MTU packet size (with this method: http://www.richard-slater.co.uk/archives/2009/10/23/change-your-mtu-under-vista-or-windows-7/), but still can't access them through ping... I don't know what to do anymore.... any suggestions???

  Read the article

• Bash delete file when variable = x

  - by twigg

  I'm creating a bash script which reboots the system at each reboot it adds a new line to a text file, I then read the text file before each reboot. Once the variable holding the number of lines reaches say 10 I want the script to delete the text file (at which point on the next reboot it will see the file isn't there, brake the loop and promote the user to start again). I tried this: exec < text.txt nol=0 while read line do nol=`expr $nol + 1` done reboot_count=10 if ["$nol" == "$reboot_count"]; then rm text.txt fi but this doesn't seem to be working, all help is appreciated :)

  Read the article

• Logging Timeout'd Request in Apache 2.X

  - by m3rLinEz

  Hello, I am migrating some applications from Apache 1.3 to 2.2. We used to run some tests where attacker opens some HTTP connection to our server, and do nothing. Apache 1.3 would log the following 408 code, for example: 126.1.86.85 - - [01/Dec/2010:06:26:19 +0000] "-" 408 - "-" 0 126.1.86.85 - - [01/Dec/2010:06:26:19 +0000] "-" 408 - "-" 0 But with Apache 2.2, nothing is logged to the log file. I run the same test by using netcat to open the connection: $ nc IP_victim PORT_victim $ nc 10.42.37.3 80 I would like to have Apache 2.2 log the same 408 code to the log file, so that we would know of attempted DoS attack from the outside. Do I need any more configuration in Apache 2 to enable this? I have tried some different configurations such as LogLevel = Debug, Timeout 30, RequestReadTimeout header=10 body=30. Thanks.

  Read the article

• Flash movie randomly freeze the browser

  - by Erick

  Just recently it seems that my flash player have had some troubles to display flash videos (youtube/dailymotions and others like this). This issue was supposed to be fixed with Flash Player 10 beta if I remember correctly. My flash player is currently at the lastest version available (10.0.45.2) I'm currently on Windows 7 x64. I tried to uninstall it and reboot and reinstall it, didn't work. Sometimes when it freeze and I reboot it "fixes" temporary the problem. The freeze problem is each and every browser. If one fails and freeze, every browsers using the plugin or ActiveX (Opera 10.5/Chrome 5/Safari 4/IE 8/FF 3.7 all installed) will freeze upon playing. I'm quite out of inspirations for fixing this up now I dare say.

  Read the article

• forward ssh ports on EC2

  - by Will Glass

  I have an SSH server on a private subnet within an EC2 vpc listening for ssh on port 9022 I also have a nat instance (standard Amazon EC2 nat) on a public instance. I would like to forward incoming SSH connections (port 9022) to my nat to the internal server (port 9022). I tried this, but it didn't work: sudo iptables -t nat -I PREROUTING -p tcp -i eth0 --dport 9022 -j DNAT --to-destination 10.0.2.11:9022 I verified that 10.0.2.11 is listening on port 9022. (I can telnet). I verified my security group allows incoming port 9022. I verified that /proc/sys/net/ipv4/ip_forward is 1. What am I missing? Edit: Turns out this was correct after all. I had a mistake in my security group.

  Read the article

• IKE Phase 1 Aggressive Mode exchange does not complete

  - by Isaac Sutherland

  I've configured a 3G IP Gateway of mine to connect using IKE Phase 1 Aggressive Mode with PSK to my openswan installation running on Ubuntu server 12.04. I've configured openswan as follows: /etc/ipsec.conf: version 2.0 config setup nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12 oe=off protostack=netkey conn net-to-net authby=secret left=192.168.0.11 [email protected] leftsubnet=10.1.0.0/16 leftsourceip=10.1.0.1 right=%any [email protected] rightsubnet=192.168.127.0/24 rightsourceip=192.168.127.254 aggrmode=yes ike=aes128-md5;modp1536 auto=add /etc/ipsec.secrets: @left.paxcoda.com @right.paxcoda.com: PSK "testpassword" Note that both left and right are NAT'd, with dynamic public IP's. My left ISP gives my router a public IP, but my right ISP gives me a shared dynamic public IP and dynamic private IP. I have dynamic dns for the public ip on the left side. Here is what I see when I sniff the ISAKMP protocol: 21:17:31.228715 IP (tos 0x0, ttl 235, id 43639, offset 0, flags [none], proto UDP (17), length 437) 74.198.87.93.49604 > 192.168.0.11.isakmp: [udp sum ok] isakmp 1.0 msgid 00000000 cookie da31a7896e2a1958->0000000000000000: phase 1 I agg: (sa: doi=ipsec situation=identity (p: #1 protoid=isakmp transform=1 (t: #1 id=ike (type=enc value=aes)(type=keylen value=0080)(type=hash value=md5)(type=auth value=preshared)(type=group desc value=modp1536)(type=lifetype value=sec)(type=lifeduration len=4 value=00015180)))) (ke: key len=192) (nonce: n len=16 data=(da31a7896e2a19582b33...0000001462b01880674b3739630ca7558cec8a89)) (id: idtype=FQDN protoid=0 port=0 len=17 right.paxcoda.com) (vid: len=16) (vid: len=16) (vid: len=16) (vid: len=16) 21:17:31.236720 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto UDP (17), length 456) 192.168.0.11.isakmp > 74.198.87.93.49604: [bad udp cksum 0x649c -> 0xcd2f!] isakmp 1.0 msgid 00000000 cookie da31a7896e2a1958->5b9776d4ea8b61b7: phase 1 R agg: (sa: doi=ipsec situation=identity (p: #1 protoid=isakmp transform=1 (t: #1 id=ike (type=enc value=aes)(type=keylen value=0080)(type=hash value=md5)(type=auth value=preshared)(type=group desc value=modp1536)(type=lifetype value=sec)(type=lifeduration len=4 value=00015180)))) (ke: key len=192) (nonce: n len=16 data=(32ccefcb793afb368975...000000144a131c81070358455c5728f20e95452f)) (id: idtype=FQDN protoid=0 port=0 len=16 left.paxcoda.com) (hash: len=16) (vid: len=16) (pay20) (pay20) (vid: len=16) However, my 3G Gateway (on the right) doesn't respond, and I don't know why. I think left's response is indeed getting through to my gateway, because in another question, I was trying to set up a similar scenario with Main Mode IKE, and in that case it looks as though at least one of the three 2-way main mode exchanges succeeded. What other explanation for the failure is there? (The 3G Gateway I'm using on the right is a Moxa G3150, by the way.)

  Read the article

• What do these messages in the Qmail maillog indicate?

  - by Griffo

  There seems to be an endless supply of messages in the Qmail maillog for a single address. Can anyone shed some light on why this might be and whether it is a problem? To me it looks like either spam or some sort of unhandled problem. It strikes me as unusual that the 'from=' field is blank. This is on a VPS using Plesk in case that's important. Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23593]: [email protected] Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23586]: from= Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23586]: [email protected] Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23585]: from= Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23585]: [email protected] Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23584]: from= Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23584]: [email protected] Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23583]: from= Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23583]: [email protected] Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23600]: from= Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23600]: [email protected] Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23599]: from= Jun 30 15:10:17 vps-1001108-595 qmail-remote-handlers[23599]: [email protected] EDIT Here's a sample of one of the emails: Received: (qmail 5603 invoked for bounce); 29 Jun 2011 07:46:31 +0100 Date: 29 Jun 2011 07:46:31 +0100 From: [email protected] To: [email protected] Subject: failure notice Hi. This is the qmail-send program at vps-1001108-595.cp.blacknight.com. I'm afraid I wasn't able to deliver your message to the following addresses. This is a permanent error; I've given up. Sorry it didn't work out. <[email protected]>: 200.147.36.13 does not like recipient. Remote host said: 450 4.7.1 Client host rejected: cannot find your hostname, [78.153.208.195] Giving up on 200.147.36.13. I'm not going to try again; this message has been in the queue too long. --- Below this line is a copy of the message. Return-Path: <[email protected]> Received: (qmail 15585 invoked by uid 48); 22 Jun 2011 07:38:26 +0100 Date: 22 Jun 2011 07:38:26 +0100 Message-ID: <[email protected]> To: [email protected] Subject: Cadastre-se e Concorra ? um Carro! MIME-Version: 1.0 Content-type: text/html; charset=iso-8859-1 From: Cielo Fidelidade <[email protected]> <!DOCTYPE HTML> <html> ... <body text removed> <html> If I understand this correctly, this is saying that an email sent by my server, from address [email protected], could not be delivered. However, [email protected] is not a valid email address on my server, so how can email be sent from this address on my server? I have tested whether my server is acting as an open relay, and it isn't. So how else could this be happening? I am getting thousands of these every day. What can I do to prevent it?

  Read the article

< Previous Page | 382 383 384 385 386 387 388 389 390 391 392 393  | Next Page >