Search Results

Search found 29064 results on 1163 pages for 'network management'.

Page 395/1163 | < Previous Page | 391 392 393 394 395 396 397 398 399 400 401 402  | Next Page >

• DNS slow after losing DNS Server

  - by Tim

  We have set up a small Windows Server 2008 R2 network with a domain controller which is also acting as the DNS server for the network (we opted to install DNS when setting up the domain). This network isn't connected to the Internet in any way, so all machines have been configured to use the IP address of the domain controller as their primary DNS and no secondary DNS server has been configured. If we shut down or unplug the network cable from the domain controller, DNS lookups become quite slow and the performance of the network suffers. For example, running a ping command using a hostname takes around 5-6 seconds to resolve the name. I presume this is because it is looking for the DNS, then falling back to some other method of resolving the names as the DNS server is now gone. All the machines have static IP addresses so we are considering just putting all entries in the HOSTS file of each machine. However, it would be nice to have a centralised DNS in case we one day change the IP of one of the machines. Is there a better way to speed this up?

  Read the article

• VPN iptables Forwarding: Net-to-net

  - by Mike Holler

  I've tried to look elsewhere on this site but I couldn't find anything matching this problem. Right now I have an ipsec tunnel open between our local network and a remote network. Currently, the local box running Openswan ipsec with the tunnel open can ping the remote ipsec box and any of the other computers in the remote network. When logged into on of the remote computers, I can ping any box in our local network. That's what works, this is what doesn't: I can't ping any of the remote computers via a local machine that is not the ipsec box. Here's a diagram of our network: [local ipsec box] ----------\ \ [arbitrary local computer] --[local gateway/router] -- [internet] -- [remote ipsec box] -- [arbitrary remote computer] The local ipsec box and the arbitrary local computer have no direct contact, instead they communicate through the gateway/router. The router has been set up to forward requests from local computers for the remote subnet to the ipsec box. This works. The problem is the ipsec box doesn't forward anything. Whenever an arbitrary local computer pings something on the remote subnet, this is the response: [user@localhost ~]# ping 172.16.53.12 PING 172.16.53.12 (172.16.53.12) 56(84) bytes of data. From 10.31.14.16 icmp_seq=1 Destination Host Prohibited From 10.31.14.16 icmp_seq=2 Destination Host Prohibited From 10.31.14.16 icmp_seq=3 Destination Host Prohibited Here's the traceroute: [root@localhost ~]# traceroute 172.16.53.12 traceroute to 172.16.53.12 (172.16.53.12), 30 hops max, 60 byte packets 1 router.address.net (10.31.14.1) 0.374 ms 0.566 ms 0.651 ms 2 10.31.14.16 (10.31.14.16) 2.068 ms 2.081 ms 2.100 ms 3 10.31.14.16 (10.31.14.16) 2.132 ms !X 2.272 ms !X 2.312 ms !X That's the IP for our ipsec box it's reaching, but it's not being forwarded. On the IPSec box I have enabled IP Forwarding in /etc/sysctl.conf net.ipv4.ip_forward = 1 And I have tried to set up IPTables to forward: *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [759:71213] -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT -A INPUT -p tcp -m state --state NEW -m tcp --dport 25 -j ACCEPT -A INPUT -p udp -m state --state NEW -m udp --dport 500 -j ACCEPT -A INPUT -p udp -m state --state NEW -m udp --dport 4500 -j ACCEPT -A INPUT -m policy --dir in --pol ipsec -j ACCEPT -A INPUT -p esp -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -s 10.31.14.0/24 -d 172.16.53.0/24 -j ACCEPT -A FORWARD -m policy --dir in --pol ipsec -j ACCEPT -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT Am I missing a rule in IPTables? Is there something I forgot? NOTE: All the machines are running CentOS 6.x Edit: Note 2: eth1 is the only network interface on the local ipsec box.

  Read the article

• Cannot connect to a VPN server - authentication failed with error code 691

  - by stacker

  When trying to connect to a VPN server, I get the 691 error code on the client, which say: Error Description: 691: The remote connection was denied because the user name and password combination you provided is not recognized, or the selected authentication protocol is not permitted on the remote access server. I validated that the username and password are correct. I also installed a certification to use with the IKEv2 security type. I also validated that the VPN server support security method. But I cannot login. In the server log I get this log: Network Policy Server denied access to a user. The user DomainName\UserName connected from IP address but failed an authentication attempt due to the following reason: The remote connection was denied because the user name and password combination you provided is not recognized, or the selected authentication protocol is not permitted on the remote access server. Any idea of what can I do? Thanks in advance! Log Name: Security Source: Microsoft-Windows-Security-Auditing Date: 12/29/2010 7:12:20 AM Event ID: 6273 Task Category: Network Policy Server Level: Information Keywords: Audit Failure User: N/A Computer: VPN.domain.com Description: Network Policy Server denied access to a user. Contact the Network Policy Server administrator for more information. User: Security ID: domain\Administrator Account Name: domain\Administrator Account Domain: domani Fully Qualified Account Name: domain.com/Users/Administrator Client Machine: Security ID: NULL SID Account Name: - Fully Qualified Account Name: - OS-Version: - Called Station Identifier: 192.168.147.171 Calling Station Identifier: 192.168.147.191 NAS: NAS IPv4 Address: - NAS IPv6 Address: - NAS Identifier: VPN NAS Port-Type: Virtual NAS Port: 0 RADIUS Client: Client Friendly Name: VPN Client IP Address: - Authentication Details: Connection Request Policy Name: Microsoft Routing and Remote Access Service Policy Network Policy Name: All Authentication Provider: Windows Authentication Server: VPN.domain.home Authentication Type: EAP EAP Type: Microsoft: Secured password (EAP-MSCHAP v2) Account Session Identifier: 313933 Logging Results: Accounting information was written to the local log file. Reason Code: 16 Reason: Authentication failed due to a user credentials mismatch. Either the user name provided does not map to an existing user account or the password was incorrect.

  Read the article

• Using "offline files sync" to sync with a local resource [closed]

  - by Kije

  Possible Duplicate: Which is the best application to Sync two folders? I have been trying get my machine (XP-Pro SP3) to sync files to a local USB drive in the same way as I can with mapped network drives. I particularly want to the sync to happen automatically when the USB is connected - in the same way that Off-line files will sync when the network drive comes on line. I can get a folder on the USB mounted as a network drive, but cannot get XP to offer the off-line files functionality. I have tried MS's SyncToy - it works as advertised, and will do scheduled and ad-hoc sync's, but does not seem to offer automatic syncs. I suspect I could do this by plugging my USB into another machine on my network - but that seems heavy handed. All insight appreciated - If you know this cannot be done please say so.

  Read the article

• Oracle Unveils Oracle’s Primavera Inspire for SAP 8.0

  - by Sylvie MacKenzie, PMP

  “To successfully manage large capital projects and maintenance operations, organizations need clear visibility into materials, resources, schedule and financial information,” said Yasser Mahmud, vice president, Oracle’s Primavera Global Business Unit. “With the enhancements delivered in Oracle’s Primavera Inspire for SAP 8.0, partners and customers can benefit from an integrated solution that not only reduces risk, but also helps ensure that projects are completed on-time and within budget. This combination simplifies management and extends customers’ investments in existing SAP project management modules.” Read all about the new release at http://www.oracle.com/us/corporate/press/1666350?sc=OPR-TW

  Read the article

• Double default gateway ubuntu server

  - by Elena

  Hi, I've just installed an Ubuntu server 9.10 on an EEEBox. This is my /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback auto wlan0 iface wlan0 inet static address 192.168.48.16 netmask 255.255.248.0 wireless-essid mynet auto eth0 iface eth0 inet static address xx.xx.xx.xx netmask 255.255.255.224 gateway xx.xx.yy.yy When I restart /etc/init.d/networking, I can access the eth0 ip address from the internet and I can ping the machines in my wifi network mynet. Everything works fine and I have one default gateway. But after some time if I check again the route I just find two default gateways: one is correct and is the previous one, but the other is the one of the wifi network. I have a quite low signal of mynet where my server is and sometimes the wifi just disconnect and then reconnect again. Then I think that this can be a problem and the dhcp of the wifi net, when reconnecting it also add a default gateway. Any idea on how to resolve this issue?

  Read the article

• Software Architecture and Software Architecture Evaluation

  How many of us have worked at places where the concept of software architecture was ridiculed for wasting time and money? Even more ridiculous to them was the concept of evaluating software architecture. I think the next time that I am in this situation again, and I hope that I never am I will have to push for this methodology in the software development life cycle. I have spent way too many hours/days/months/years working poorly architected systems or systems that were just built ADHOC. This in software development must stop. I can understand why systems get like this due to overzealous sales staff, demanding management that wants everything yesterday, and project managers asking if things are done yet before the project has even started. But seriously, some time must be spent designing the applications that we write along with evaluating the architecture so that it will integrate will within the existing systems of an origination. If placed in this situation again, I will strive to gain buying from key players within the business, for example: Senior Software Engineers\Developers, Software Architects, Project Managers, Software Quality Assurance, Technical Services, Operations, and Finance in order for this idea to succeed with upper management. In order to convince these key players I will have to show them the benefits of architecture and even more benefits of evaluating software architecture on a system wide level. Benefits of Software Architecture Evaluation Places Stakeholders in the Same Room to Communicate Ensures Delivery of Detailed Quality Goals Prioritizes Conflicting Goals Requires Clear Explication Improves the Quality of Documentation Discovers Opportunities for Cross-Project Reuse Improves Architecture Practices Once I had key player buy in then and only then would I approach upper management about my plan regarding implementing the concept of software architecture and using evaluation to ensure that the software being designed is the proper architecture for the project. In addition to the benefits listed above I would also show upper management how much time is being wasted by not doing these evaluations. For example, if project X cost us Y amount, then why do we have several implementations in various forms of X and how much money and time could we have saved if we just reused the existing code base to give each system the same functionality that was already created? After this, I would mention what would happen if we had 50 instances of this situation? Then I would show them how the software architecture evaluation process would have prevented this and that the optimization could have leveraged its existing code base to increase the speed and quality of its development. References:Carnegie Mellon Software Engineering Institute (2011). Architecture Tradeoff Analysis Method from http://www.sei.cmu.edu/architecture/tools/evaluate/atam.cfm

  Read the article

• Discount Codes Galore

  - by Cassandra Clark

  Saving money is at the top of everyones list right now. With this in mind the Oracle Technology Network team has compiled a list of discounts available at the Oracle Store. We are also introducing an Oracle Technology Network member discount from O'Reilly Media. If you subscribe to any of the Oracle Technology newsletters you also saw special discounts from CRC Press, Packt Publishing and Apress. We are going to do our best to bring you more offers like this every month. Now on to the discounts... Oracle Store offers - all below expiring May 31st 2010. Don't miss out! Expand Your Productivity with Oracle Open Office and Save 15%? Enter OTNOffice at checkout. Buy Now! Drive Business Agility and Performance with Industry-leading Oracle Database Management Packs.  Save 10% when you purchase them at the Oracle Store. Enter OTNDBMP at checkout. Buy Now! 15% Savings on Oracle Virtualization and Unbreakable Linux Support at the Oracle Store Enter code OTNLinuxVM at checkout. Buy Now! 20% Savings on Oracle SQL Developer Data Modeler Use OTNSQL at checkout. Buy Now! O'Reilly Oracle Technology Network Member Offer O'Reilly is generously offering Oracle Technology Network Members 35% off for print books and 40% off of eBooks. Browse Oracle titles at- http://oreilly.com/pub/topic/oracle. Use discount code TECNT at checkout.

  Read the article

• Setup MSSQL replication with peer to peer topology: problem setting up Conflict Detection

  - by Roel

  Hi, I'm setting up a SQL Replication strategy, using MSSQL2008 with peer-to-peer publications (2 servers, each one subscribes to the other). I followed this HOWTO from MSDN, and the setup seems to be working fine: add a record to one table on server A, query on server B shows the new record. So far, so good. So far I only have one table 'Templates': Id PK (calculated field) NodeId int default 1/2 (Server A = 1, Server B = 2) LocalId int autoid Name nvarchar(100) Now, I would like to enable 'Conflict detection', which should be enabled by default. But every time I try to save the 'Conflict Detection' feature in the Publication Properties I get the following error: Cannot save Peer conflict detection properties. An exception occurred while executing a Transact-SQL statement or batch.(Microsoft.SqlServer.ConnectionInfo) Program Location: at Microsoft.SqlServer.Management.Common.ServerConnection.ExecuteNonQuery(String sqlCommand, ExecutionTypes executionType) at Microsoft.SqlServer.Management.Common.ServerConnection.ExecuteNonQuery(String sqlCommand) at Microsoft.SqlServer.Replication.ReplicationObject.ExecCommand(String commandIn) at Microsoft.SqlServer.Replication.TransPublication.SetPeerConflictDetection(Boolean enablePeerConflictDetection, Int32 peerOriginatorID) at Microsoft.SqlServer.Management.UI.PubPropSubscriptionOptions.SaveP2PConflictDetection() at Microsoft.SqlServer.Management.UI.PubPropSubscriptionOptions.SaveProperties(ExecutionMode& executionResult) Column name 'Id' does not exist in the target table or view. Changed database context to 'TestDB'. (.Net SqlClient Data Provider) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&ProdVer=10.00.2531&EvtSrc=MSSQLServer&EvtID=1911&LinkId=20476 Server Name: SERVER_A Error Number: 1911 Severity: 16 State: 1 Line Number: 2 Program Location: at System.Data.SqlClient.SqlConnection.OnError(SqlException exception, Boolean breakConnection) at System.Data.SqlClient.SqlInternalConnection.OnError(SqlException exception, Boolean breakConnection) at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning(TdsParserStateObject stateObj) at System.Data.SqlClient.TdsParser.Run(RunBehavior runBehavior, SqlCommand cmdHandler, SqlDataReader dataStream, BulkCopySimpleResultSet bulkCopyHandler, TdsParserStateObject stateObj) at System.Data.SqlClient.SqlCommand.RunExecuteNonQueryTds(String methodName, Boolean async) at System.Data.SqlClient.SqlCommand.InternalExecuteNonQuery(DbAsyncResult result, String methodName, Boolean sendToPipe) at System.Data.SqlClient.SqlCommand.ExecuteNonQuery() at Microsoft.SqlServer.Management.Common.ServerConnection.ExecuteNonQuery(String sqlCommand, ExecutionTypes executionType) Now, I googled the hell out of this error, and nothing shows up. I also can't seem to find out what the exact target table of the error "Column name 'Id' does not exist..." is. Has anyone every done this successfully? Am I missing something? Having this setup without conflict detection feels pretty useless... EDIT OK, so after some more research and setting up with different databases etc, I found out that the calculated 'Id' column of the Templates table is the culprit. I don't know why, but the replication doesn't seem to allow calculated columns (which are also primary key). It works now too, without the 'Id' column, and using the NodeId and LocalId as a combined PK. So now the question is, why isn't it allowed to have a calculated column as PK for replication with conflict detection?

  Read the article

• Keep Oracle VM 3 Up to Date

  - by Honglin Su

  More and more customers turn to Oracle VM 3 to virtualize their enterprise applications. Oracle VM support subscription is an integrated part of their successes. Customers enjoy the benefit of the industry-leading global support 24x7 for their server virtualization implementation, and receive access to patches, fixes, and updates via Unbreakable Linux Network (ULN). For customers running Oracle systems, Oracle VM support is included in Oracle Premium Support for Systems at no extra cost, and customers receive comprehensive systems coverage that includes single point accountability for Oracle server and storage hardware; integrated software (for example, firmware); and operating system software (Oracle Solaris, Oracle Linux, and Oracle VM). To run a successful virtualization infrastructure, it's important to keep Oracle VM 3 environment up to date by leveraging Oracle VM support resources.  Oracle VM Server Updates: You can easily upgrade Oracle VM Server using a Yum repository. You can download the latest server patch updates from ULN. To receive notification on the software update delivered to Oracle ULN for Oracle VM, you can sign up here. For information on setting up an Oracle VM Server Yum repository and using Oracle VM Manager to perform the upgrade of Oracle VM Servers, see Updating and Upgrading Oracle VM Servers in the Oracle VM User's Guide .  Oracle VM Manager Updates: Get the download instructions at OTN, and apply latest Oracle VM Manager patch. Be sure to review the patch README before you apply the patches. Support customers have access to extremely valuable knowledge notes from My Oracle Support. They are the first to receive useful tips to help address issues in Oracle VM deployments. For example, Upgrade to Oracle VM 3.1.1 using Yum Repository may cause network configuration scripts to be renamed causing network failure after reboot (Doc ID 1464126.1) Oracle VM server reboots after network becomes unresponsive due to deep C-State power management setting (Doc ID 1440197.1) For more information about Oracle's virtualization, visit oracle.com/virtualization.

  Read the article

• Realtek drivers for Redhat Linux

  - by kv

  Can any one provide link to: RedHat Linux realteak 8168C Network Drivers Zenith

  Read the article

• Cisco 891w multiple VLAN configuration

  - by Jessica

  I'm having trouble getting my guest network up. I have VLAN 1 that contains all our network resources (servers, desktops, printers, etc). I have the wireless configured to use VLAN1 but authenticate with wpa2 enterprise. The guest network I just wanted to be open or configured with a simple WPA2 personal password on it's own VLAN2. I've looked at tons of documentation and it should be working but I can't even authenticate on the guest network! I've posted this on cisco's support forum a week ago but no one has really responded. I could really use some help. So if anyone could take a look at the configurations I posted and steer me in the right direction I would be extremely grateful. Thank you! version 15.0 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname ESI ! boot-start-marker boot-end-marker ! logging buffered 51200 warnings ! aaa new-model ! ! aaa authentication login userauthen local aaa authorization network groupauthor local ! ! ! ! ! aaa session-id common ! ! ! clock timezone EST -5 clock summer-time EDT recurring service-module wlan-ap 0 bootimage autonomous ! crypto pki trustpoint TP-self-signed-3369945891 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-3369945891 revocation-check none rsakeypair TP-self-signed-3369945891 ! ! crypto pki certificate chain TP-self-signed-3369945891 certificate self-signed 01 (cert is here) quit ip source-route ! ! ip dhcp excluded-address 192.168.1.1 ip dhcp excluded-address 192.168.1.5 ip dhcp excluded-address 192.168.1.2 ip dhcp excluded-address 192.168.1.200 192.168.1.210 ip dhcp excluded-address 192.168.1.6 ip dhcp excluded-address 192.168.1.8 ip dhcp excluded-address 192.168.3.1 ! ip dhcp pool ccp-pool import all network 192.168.1.0 255.255.255.0 default-router 192.168.1.1 dns-server 10.171.12.5 10.171.12.37 lease 0 2 ! ip dhcp pool guest import all network 192.168.3.0 255.255.255.0 default-router 192.168.3.1 dns-server 10.171.12.5 10.171.12.37 ! ! ip cef no ip domain lookup no ipv6 cef ! ! multilink bundle-name authenticated license udi pid CISCO891W-AGN-A-K9 sn FTX153085WL ! ! username ESIadmin privilege 15 secret 5 $1$g1..$JSZ0qxljZAgJJIk/anDu51 username user1 password 0 pass ! ! ! class-map type inspect match-any ccp-cls-insp-traffic match protocol cuseeme match protocol dns match protocol ftp match protocol h323 match protocol https match protocol icmp match protocol imap match protocol pop3 match protocol netshow match protocol shell match protocol realmedia match protocol rtsp match protocol smtp match protocol sql-net match protocol streamworks match protocol tftp match protocol vdolive match protocol tcp match protocol udp class-map type inspect match-all ccp-insp-traffic match class-map ccp-cls-insp-traffic class-map type inspect match-any ccp-cls-icmp-access match protocol icmp class-map type inspect match-all ccp-invalid-src match access-group 100 class-map type inspect match-all ccp-icmp-access match class-map ccp-cls-icmp-access class-map type inspect match-all ccp-protocol-http match protocol http ! ! policy-map type inspect ccp-permit-icmpreply class type inspect ccp-icmp-access inspect class class-default pass policy-map type inspect ccp-inspect class type inspect ccp-invalid-src drop log class type inspect ccp-protocol-http inspect class type inspect ccp-insp-traffic inspect class class-default drop policy-map type inspect ccp-permit class class-default drop ! zone security out-zone zone security in-zone zone-pair security ccp-zp-self-out source self destination out-zone service-policy type inspect ccp-permit-icmpreply zone-pair security ccp-zp-in-out source in-zone destination out-zone service-policy type inspect ccp-inspect zone-pair security ccp-zp-out-self source out-zone destination self service-policy type inspect ccp-permit ! ! crypto isakmp policy 1 encr 3des authentication pre-share group 2 ! crypto isakmp client configuration group 3000client key 67Nif8LLmqP_ dns 10.171.12.37 10.171.12.5 pool dynpool acl 101 ! ! crypto ipsec transform-set myset esp-3des esp-sha-hmac ! crypto dynamic-map dynmap 10 set transform-set myset ! ! crypto map clientmap client authentication list userauthen crypto map clientmap isakmp authorization list groupauthor crypto map clientmap client configuration address initiate crypto map clientmap client configuration address respond crypto map clientmap 10 ipsec-isakmp dynamic dynmap ! ! ! ! ! interface FastEthernet0 ! ! interface FastEthernet1 ! ! interface FastEthernet2 ! ! interface FastEthernet3 ! ! interface FastEthernet4 ! ! interface FastEthernet5 ! ! interface FastEthernet6 ! ! interface FastEthernet7 ! ! interface FastEthernet8 ip address dhcp ip nat outside ip virtual-reassembly duplex auto speed auto ! ! interface GigabitEthernet0 description $FW_OUTSIDE$$ES_WAN$ ip address 10...* 255.255.254.0 ip nat outside ip virtual-reassembly zone-member security out-zone duplex auto speed auto crypto map clientmap ! ! interface wlan-ap0 description Service module interface to manage the embedded AP ip unnumbered Vlan1 arp timeout 0 ! ! interface Wlan-GigabitEthernet0 description Internal switch interface connecting to the embedded AP switchport trunk allowed vlan 1-3,1002-1005 switchport mode trunk ! ! interface Vlan1 description $ETH-SW-LAUNCH$$INTF-INFO-FE 1$$FW_INSIDE$ ip address 192.168.1.1 255.255.255.0 ip nat inside ip virtual-reassembly zone-member security in-zone ip tcp adjust-mss 1452 crypto map clientmap ! ! interface Vlan2 description guest ip address 192.168.3.1 255.255.255.0 ip access-group 120 in ip nat inside ip virtual-reassembly zone-member security in-zone ! ! interface Async1 no ip address encapsulation slip ! ! ip local pool dynpool 192.168.1.200 192.168.1.210 ip forward-protocol nd ip http server ip http access-class 23 ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ! ! ip dns server ip nat inside source list 23 interface GigabitEthernet0 overload ip route 0.0.0.0 0.0.0.0 10.165.0.1 ! access-list 23 permit 192.168.1.0 0.0.0.255 access-list 100 remark CCP_ACL Category=128 access-list 100 permit ip host 255.255.255.255 any access-list 100 permit ip 127.0.0.0 0.255.255.255 any access-list 100 permit ip 10.165.0.0 0.0.1.255 any access-list 110 permit ip 192.168.0.0 0.0.5.255 any access-list 120 remark ESIGuest Restriction no cdp run ! ! ! ! ! ! control-plane ! ! alias exec dot11radio service-module wlan-ap 0 session Access point version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname ESIRouter ! no logging console enable secret 5 $1$yEH5$CxI5.9ypCBa6kXrUnSuvp1 ! aaa new-model ! ! aaa group server radius rad_eap server 192.168.1.5 auth-port 1812 acct-port 1813 ! aaa group server radius rad_acct server 192.168.1.5 auth-port 1812 acct-port 1813 ! aaa authentication login eap_methods group rad_eap aaa authentication enable default line enable aaa authorization exec default local aaa authorization commands 15 default local aaa accounting network acct_methods start-stop group rad_acct ! aaa session-id common clock timezone EST -5 clock summer-time EDT recurring ip domain name ESI ! ! dot11 syslog dot11 vlan-name one vlan 1 dot11 vlan-name two vlan 2 ! dot11 ssid one vlan 1 authentication open eap eap_methods authentication network-eap eap_methods authentication key-management wpa version 2 accounting rad_acct ! dot11 ssid two vlan 2 authentication open guest-mode ! dot11 network-map ! ! username ESIadmin privilege 15 secret 5 $1$p02C$WVHr5yKtRtQxuFxPU8NOx. ! ! bridge irb ! ! interface Dot11Radio0 no ip address no ip route-cache ! encryption vlan 1 mode ciphers aes-ccm ! broadcast-key vlan 1 change 30 ! ! ssid one ! ssid two ! antenna gain 0 station-role root ! interface Dot11Radio0.1 encapsulation dot1Q 1 native no ip route-cache bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface Dot11Radio0.2 encapsulation dot1Q 2 no ip route-cache bridge-group 2 bridge-group 2 subscriber-loop-control bridge-group 2 block-unknown-source no bridge-group 2 source-learning no bridge-group 2 unicast-flooding bridge-group 2 spanning-disabled ! interface Dot11Radio1 no ip address no ip route-cache shutdown ! encryption vlan 1 mode ciphers aes-ccm ! broadcast-key vlan 1 change 30 ! ! ssid one ! antenna gain 0 dfs band 3 block channel dfs station-role root ! interface Dot11Radio1.1 encapsulation dot1Q 1 native no ip route-cache bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface GigabitEthernet0 description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router no ip address no ip route-cache ! interface GigabitEthernet0.1 encapsulation dot1Q 1 native no ip route-cache bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled ! interface GigabitEthernet0.2 encapsulation dot1Q 2 no ip route-cache bridge-group 2 no bridge-group 2 source-learning bridge-group 2 spanning-disabled ! interface BVI1 ip address 192.168.1.2 255.255.255.0 no ip route-cache ! ip http server no ip http secure-server ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag access-list 10 permit 192.168.1.0 0.0.0.255 radius-server host 192.168.1.5 auth-port 1812 acct-port 1813 key ***** bridge 1 route ip

  Read the article

• ISA 2006 refuses VPN DHCP requests as spoofing

  - by Daniel

  I'm running ISA 2006 with PPTP VPN for my AD-controlled network. DHCP is located on the ISA server itself and authentication is done by RADIUS (NPS) located on the DC. Right now my VPN clients can connect, access local DNS, and can ping ISA, the DC, and other clients. Here's where it gets weird. I noticed that despite all this, ipconfig shows the following: PPP adapter North Horizon VPN: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : North Horizon VPN Physical Address. . . . . . . . . : DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 10.42.4.7(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : 0.0.0.0 DNS Servers . . . . . . . . . . . : 10.42.1.10 NetBIOS over Tcpip. . . . . . . . : Enabled So I went over and checked my ISA logs for both DHCP requests and replies, only to find out that my VPN clients are being denied because ISA thinks its a spoof. Here's some relevant information from the log (the VPN subnet is 10.42.4.0/24): Client IP: 10.42.4.6 Destination: 255.255.255.255:67 Client Username: (blank) Protocol: DHCP (request) Action: Denied Connection Rule: (blank) Source Network: VPN Clients Destination Network: Local Host Result Code: 0xc0040014 FWX_E_FWE_SPOOFING_PACKET_DROPPED Network Interface: 10.42.4.11 --------------------------------------------------------- Original Client IP: 10.42.4.6 Destination: 10.42.1.1 Client Username: (valid user) Protocol: PING Action: Initiated Connection Rule: Allow PING to ISA Source Network: VPN Clients Destination Network: Local Host Result Code: 0x0 ERROR_SUCCESS Network Interface: (blank) I wasn't sure what this 10.42.4.11 network interface was - it certainly wasn't something I had setup - untill I saw it in Routing and Remote Access under IP Routing General as an interface called "Internal" bound to the same IP address. I also noticed that since ISA takes blocks of 10 IP addresses from DHCP for VPN, it had reserved 10.42.4.2-11. I'm not sure if it means anything, though. Thanks for your help.

  Read the article

• Assistance in setting up new APC Smart-UPS RT on a new VMware enviroment

  - by user38085

  I'm new to the realm of setting up a APC Smart-UPS RT 8000VA UPS with a management network card (AP9618). The project calls for the upgrade of the firmware for the network card to the newest and greatest. It also calls for the Powerchute Business Software to be installed with notifications setup per email for temperature, shutdown, and battery low. I know I'll have to use the serial cable to flash the firmware and install the software on one server 2003 box. Also on that server I'll have to install the software and setup the GUI (IP address) interface. Whats confusing the most is the whole process, and steps to use without taking down the network, which would be very bad. In flashing the firmware does it take down the UPS? Do i have to run BOOTP commands to setup the network card? Also no agents will be used on any of the VWware OS's and no SNMP trap will be used.

  Read the article

• Is there a way to tell what the download speed is from a site/server

  - by Memor-X

  i'm looking into which ISP i should go with at the place i'm moving into, one ISP which i have been told good things about has data limits (which when breached will drop your speed to dial-up speed) but multiple memberships which, apart from the cheapest membership, have the same data limits (the cheapest has a 10GB data limit) in their fine print, they say that each different membership has different port speeds, one particular part jumps out at me These speeds are the NBN (National Broadband Network) port speed and not the actual Internet data speed which will vary based on numerous factors including destination you are reaching, your network equipment, network congestion etc. i plan to use the net to download DLC and patch updates for games (particular the insanely large update for the Wii U) and games from Steam (if i find any good one other than this one JRPG) and downloading development resources from free sites like Deposit Files and Mediafire since one membership with a 1000GB data limit is $145 with the port speed being 12Mbps/1Mbps (cheapest) while another with the same limit is $190 with the port speed of 100Mbps/40Mbps (expensive) i am wondering how i can tell what the speed coming from site is since i don't want to be wasting money on speed that makes no difference (unlike memory which i rather have to spare) NOTE: the speeds are for a fiber optic network which where my new place is can only connect via fixed wireless which i may not be able to get with this ISP but if i can get this network then good NOTE 2: most of the resources i get from Deposit Files are always about 200 MB or less, if a resource pack is greater then it's split into multiple archives (like .7z.part) while Mediafire i have to see one bigger than 150MB NOTE 3: one update patch for a PS3 game is close to 4 GB (Disgaea 4) which i need to get access to the DLC and on the weekend i downloaded 5 GB for the Final Fantasy XIV Open Beta for the PS3 which took almost 5 hours

  Read the article

• ING Selecciona Oracle Fusion HCM para la Gestión del Capital Humano

  - by Noelia Gomez

  Normal 0 21 false false false ES X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-family:"Calibri","sans-serif";} La decisión de ING sobre la elección de Oracle Fusion HCM fue impulsada por su deseo continuo de fortalecer la función de RRHH para impulsar su negocio. Tras mucho tiempo como cliente de Oracle PeopleSoft HCM, evaluó el segmento de mercado de HCM antes de seleccionar Oracle Fusion HCM, con el objetivo de seguir utilizando las herramientas principales de recursos humanos y mantener su posición como uno de los principales empleadores en los Países Bajos. ING implementará Oracle Fusion HCM, en estrecha colaboración con NorthgateArinso, miembro de Oracle PartnerNetwork (Gold), que proporcionará los servicios de alojamiento y de Oracle Consulting. La firma de servicios financieros utilizará toda la suite de Oracle Fusion Global Human Resources y Oracle Talent Management incluyendo Oracle Fusion Goal, Oracle Fusion OTBI, Oracle Fusion Workforce Compensation, Oracle Fusion Benefits y Oracle Fusion Performance Management. Además, ING implementará Oracle Fusion Financials, aprovechando la plataforma unificada de Oracle Fusion Applications. “Como institución financiera líder y mejor empleador, ING considera a sus colaboradores el activo más estratégico. Continuar siendo “best-in-class” en recursos humanos, es un diferenciador competitivo para nosotros, y necesitamos una aplicación líder de HCM para complementar nuestros esfuerzos ", dijo Marijke Brunklaus, Director General de Recursos Humanos de ING Bank Países Bajos. "Siendo un antiguo usuario de Oracle PeopleSoft HCM, cuidadosamente hemos evaluado las posibles soluciones disponibles y elegimos Oracle Fusion HCM como nuestra futura plataforma. Las profundas capacidades globales y las herramientas principales de talento de Oracle Fusion HCM son una buena opción para ayudarnos a evolucionar continuamente en nuestro negocio". Puede conocer más sobre HCM Fusion : · Oracle Fusion Applications · Oracle Fusion Human Capital Management · Oracle PartnerNetwork · Oracle Consulting Services · Oracle Human Capital Management Blog · Oracle HCM on Twitter · Oracle HCM on Facebook

  Read the article

• Windows Server 2008R2 - can't change or remove the default gateway

  - by disserman

  We've installed VMWare Server 2.0 on Windows 2008R2. After some time playing with it (actually only removing host-only and nat networks, and binding adapters to the specified vmnets) we've noticed a strange problem: if you change or remove the default gateway on the network card, the server completely loses a network connection you can't ping it from the subnet, it also can't connect to anyone. When the gateway is removed and a server tries to connect to the other machines, I can see some incoming packets using a sniffer, but I believe they are damaged in some kind (I'm not a mega-guru in TCP/IP and can't find a mistake in a binary translation of the packet) because the other side doesn't respond. What we tried: removed vmware server using add/remove programs deleted everything related to the vmware server and all installed network adapters in the windows registry double checked for the vmware bridged protocol driver file, it's physically absent and no any links in the registry. performed a tcp/ip reset with netsh and disabled/enabled all network adapters in the device manager to recreate a registry keys for them. tried another network adapter. and the situation is the same: as soon you remove or change the default gateway, windows stops working. The total absurd of the situation is that the default gateway points to the non-existing IP. But when it's set, you can ping a server from the subnet, when you remove it - you can't. Any help? I'm starting thinking the new build of the VMWare Server is some kind of the malware... :)

  Read the article

• Keywords Optimization For Website Optimization

  Saying that you need to do website optimization sounds like saying you need to get healthy. To get healthy we do 2 things: diet management and exercise. Lets start with diet management. Keywords are like food for your WebPages. This article explains the role of keywords in website optimization.

  Read the article

• IPCop Packet Mangling

  - by Zenham

  I've found myself in a pickle replacing an old firewall for a client this afternoon. I'm configuring their new IPCop firewall (1.4.21), Zerina OpenVPN addon is installed. What I need to do: There are three network interfaces, currently set up as red (WAN), green (LAN, 192.168.20.0/24) and orange (remote network 10.1.20.0/24). The orange interface is a direct fiber link to another organization. Simple description: Traffic and networks appear to be properly configured at this point, but I have many (150+) specific IPs on the LAN which, when accessing the resources on the 10.1.20.x network, need to be mangled to appear to be coming from the 10.1.20.0/24 network (and return traffic properly delivered). The routing on the far side was configured earlier and should be fine, but I need to redirect any packets coming across destined for those IPs to end up at their proper destination. The addressing is fixed and predictable (ie. 192.168.20.125 - 10.1.20.125). I need to insert whatever rules I have into the IPCop ruleset through /etc/rc.local I know, I'm just not sure about how I should structure this. There's CUSTOMOUTPUT and CUSTOMINPUT targets, both which currently just consist of the single rule redirecting packets to the OVPNOUTPUT/OVPNINPUT targets, so I'm guessing I should insert a rule matching outbound packets destined for the 10.1.20.x network and redirecting to a new target (maybe called TO-ORANGE) and a rule at the top of CUSTOMINPUT which redirects to a FROM-ORANGE target. Under those targets, I would have rules which do the IP matching and mangling. Am I approaching this right? If so, I'm not very familiar with mangle, and would appreciate seeing examples of how to write that source-IP rewrite. If not, how would you suggest doing this? TIA! edit: I notice additionally that the nat table has CUSTOMPREROUTING and CUSTOMPOSTROUTING targets, I guess I could alternatively post the rules in there....

  Read the article

• How to ping virtualbox guest machine by hostname?

  - by Punit Soni

  Here is the summary. VirtualBox 4.2.18 Host OS: Windows 7 Guest OS: Ubuntu 12.04 Networking: Bridged Adaptor I can ping Host and other machines in host's network from ubuntu guest using hostnames. But, I can only ping the guest machine using IP address from host and network machines. I have avahi-daemon running on Guest OS. I want to be able to ping/ssh the guest machine from host and other machines on network using hostname of the guest machine. Please help.

  Read the article

• COLLABORATE 12: Oracle WebCenter Featured at Largest Oracle User Conference

  - by kellsey.ruppel

  With more than 70 out of about 800 individual sessions, Oracle WebCenter will be a major focus of COLLABORATE 12, this year's Independent Oracle User Group (IOUG) conference, taking place April 22–26 in Las Vegas, Nevada. "COLLABORATE 12 provides a unique chance to share experiences with Oracle customers, product managers, and partners, so you can deepen your knowledge about Oracle WebCenter upgrades, user provisioning, workflow, integration, and much more," says Roel Stalman, vice president of product management for Oracle WebCenter. "In fact, COLLABORATE can form a key part of your training plans for 2012." Full-Day Oracle WebCenter Deep Dive On Sunday, April 22, from 9 a.m. to 3 p.m., registered conference attendees can attend a special deep dive into Oracle WebCenter. During the program, experts from Oracle product management and development teams will delve into all four pillars of Oracle WebCenter—and explore how all four are integrated together. Attendees can also expect A preview of Oracle WebCenter 12c Detailed product demos Prize giveaways throughout the day Going Mobile Oracle WebCenter and mobile technology will be a major theme at this year's conference, with a number of sessions devoted to maximizing the availability of content while also ensuring security. Sessions include Are You Making These Mistakes in Your Oracle Site Studio Implementations? Monday, April 23 at 11 a.m. Case Study: How Medtronic Brought Oracle WebCenter Content to the iPad Tuesday, April 24 at 10:45 a.m. Exposing Oracle WebCenter Data on Mobile and Desktop Devices Through the REST API Tuesday, April 24 at 10:45 a.m. Mobile First: Delivering a Compelling Mobile Experience with Oracle WebCenter Tuesday, April 24 at 4:30 p.m. Optimizing Your Oracle WebCenter Portal Solution for Mobile Devices Wednesday, April 25 at 8:15 a.m. Build an iPhone App Using Oracle WebCenter Portal REST APIs Wednesday, April 25 at 9:30 a.m. Other Don't-Miss Sessions Conference organizers have indicated that the following sessions in particular should be of wide interest to attendees. Oracle WebCenter: Vision, Strategy, and Overview Monday, April 23 at 9:45 a.m. This session explores Oracle's integrated approach to portals and composite applications, Web experience management, enterprise content management, and enterprise social collaboration. It also provides insight into Oracle's strategic direction for Oracle WebCenter. Oracle Webcenter Content, Oracle WebCenter Spaces, Oracle WebCenter Sites: Which Is Right for Me? Monday, April 23 at 1:15 p.m. This session helps attendees determine the best Oracle WebCenter solution to meet their needs for an intranet, corporate Website, or partner portal. Learn more and register to attend COLLABORATE 12.

  Read the article

• Office 2010 Professionl Plus Trial - Product Activation Fails

  - by Think Floyd

  I have installed Office 2010 Professional Plus Beta trial (x64 version) from MSFT site. Every thing worked fine initially. But after I rebooted machine (Win7 x64), and started Outlook 2010, i see an error dialog that I am not in a "corporate network" and the product could not be activated. I am not in a corporate network. I would like to use Office 2010 on my home network. How do I get around the Product Activation issue?

  Read the article

• How to set Virtualbox appliance as webdev portable sollution?

  - by tenshimsm

  I just want to set a a Virtualbox virtual appliance to make it portable. Meaning that I'll enable a network config which will not need to be changed when I am using my laptop in a different network. I want the virtual machine to have internet access to keep it updated and be able to always have direct access from host using, for example, the IP 10.0.2.100 even when I am in a 192.168.0.1 network. So the first virtual network adapter will have a static ip (10.0.2.100) and the second will receive it from the DHCP. I don't know if 2 virtual adapters are needed or just one to accomplish that.

  Read the article

• Guidance and Pricing for MSDN 2010

  - by John Alexander

  Sorry for the rather lengthy post here. I get asked this all the time so I decided to post it…Visual Studio 2010 editions will be available on April 12, 2010. Product Features Professional with MSDN Essentials Professional with MSDN Premium with MSDN Ultimate with MSDN Test Professional with MSDN Debugging and Diagnostics IntelliTrace (Historical Debugger)         Static Code Analysis       Code Metrics       Profiling       Debugger   Testing Tools Unit Testing   Code Coverage       Test Impact Analysis       Coded UI Test       Web Performance Testing         Load Testing1         Microsoft Test Manager 2010       Test Case Management2       Manual Test Execution       Fast-Forward for Manual Testing       Lab Management Configuration3       Integrated Development Environment Multiple Monitor Support   Multi-Targeting   One Click Web Deployment   JavaScript and jQuery Support   Extensible WPF-Based Environment Database Development Database Deployment       Database Change Management2       Database Unit Testing       Database Test Data Generation       Data Access   Development Platform Support Windows Development   Web Development   Office and SharePoint Development   Cloud Development   Customizable Development Experience   Architecture and Modeling Architecture Explorer         UML® 2.0 Compliant Diagrams (Activity, Use Case, Sequence, Class, Component)         Layer Diagram and Dependency Validation         Read-only diagrams (UML, Layer, DGML Graphs)         Lab Management Virtual environment setup & tear down3       Provision environment from template3       Checkpoint environment3       Team Foundation Server Version Control2   Work Item Tracking2   Build Automation2   Team Portal2   Reporting & Business Intelligence2   Agile Planning Workbook2   Microsoft Visual Studio Team Explorer 2010   Test Case Management2       MSDN Subscription – Software and Services for Production Use Windows Azure Platform 20 hrs/mo † 50 hrs/mo † 100 hrs/mo † 250 hrs/mo † n/a Microsoft Visual Studio Team Foundation Server 2010   Microsoft Visual Studio Team Foundation Server 2010 CAL   1 1 1 1 Microsoft Expression Studio 3       Microsoft Office Professional Plus 2010, Project Professional 2010, Visio Premium 2010 (following Office 2010 launch)       MSDN Subscription – Software for Development and Testing 4 Windows 7, Windows Server 2008 R2 and SQL Server 2008 Toolkits, Software Development Kits, Driver Development Kits Previous versions of Windows (client and server operation systems)   Previous versions of Microsoft SQL Server   Microsoft Office       Microsoft Dynamics       All other Servers       Windows Embedded operating systems       Teamprise         MSDN Subscription – Other Benefits Technical support incidents 0 2 4 4 2 Priority support in MSDN Forums Microsoft e-learning collections (typically 10 courses or 20 hours) 0 1 2 2 1 MSDN Flash newsletter MSDN Online Concierge MSDN Magazine   System Requirements View View View View View Buy from (MSRP) $799 $1,199 $5,469 $11,899 $2,169 Renew from (MSRP) $549 (upgrade) $799 $2,299 $3,799 $899 † Availability varies by country and subscription level.  Details available on the MSDN site 1. May require one or more Microsoft Visual Studio Load Test Virtual User Pack 2010 2. Requires Team Foundation Server and a Team Foundation Server CAL 3. Requires Microsoft Visual Studio Lab Management 2010 4. Per-user license allows unlimited installations and use for designing, developing, testing, and demonstrating applications. UML is a registered trademark of Object Management Group, Inc. Windows is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.

  Read the article

• What is the difference between a Facebook Group and a Facebook Page

  - by jmort253

  I created a Project Management Stack Exchange Facebook Page to help promote the new Project Management Stack Exchange Site. One of the users suggested a Facebook Group instead. I use Facebook, and I've searched the help pages, but it's not immediately clear to me what the advantages and disadvantages are. Can you provide a list of uses for Groups and uses for Facebook Pages and perhaps some links to resources that help differentiate one from the other?

  Read the article

< Previous Page | 391 392 393 394 395 396 397 398 399 400 401 402  | Next Page >