Search Results

Search found 11207 results on 449 pages for 'kiosk mode'.

Page 396/449 | < Previous Page | 392 393 394 395 396 397 398 399 400 401 402 403 | Next Page >

Cliq Wireless questions

- by Nathan Adams

Heres the deal: I am by no means a Linux expert, even less when it comes to the Android OS but lets see if we can't solve this problem. The problem I am having is that on the Cliq we have a broadcom chip. In order to use the wireless card you must first insert the module into the kernel. Fine: # insmod /system/lib/dhd.ko insmod /system/lib/dhd.ko # lsmod lsmod dhd 164936 0 - Live 0xbf000000 # BUT netcfg (or ifconfig in busybox) does not recognize that there is a wireless adapter there: # netcfg netcfg lo UP 127.0.0.1 255.0.0.0 0x00000049 dummy0 DOWN 0.0.0.0 0.0.0.0 0x00000082 rmnet0 UP 14.67.164.2 255.255.255.252 0x00001043 rmnet1 DOWN 0.0.0.0 0.0.0.0 0x00001002 rmnet2 DOWN 0.0.0.0 0.0.0.0 0x00001002 usb0 DOWN 0.0.0.0 0.0.0.0 0x00001002 # busybox ifconfig busybox ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:282 errors:0 dropped:0 overruns:0 frame:0 TX packets:282 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:18754 (18.3 KiB) TX bytes:18754 (18.3 KiB) rmnet0 Link encap:Ethernet HWaddr EE:83:E8:B4:4A:ED inet addr:14.x.x.x Bcast:14.67.164.3 Mask:255.255.255.252 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7148 errors:0 dropped:0 overruns:0 frame:0 TX packets:7659 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2609236 (2.4 MiB) TX bytes:908575 (887.2 KiB) # For giggles if we attempt to launch wpa_supplicant anyways we get this: # wpa_supplicant -Dwext -ieth0 -c/data/misc/wifi/wpa_supplicant.conf wpa_supplicant -Dwext -ieth0 -c/data/misc/wifi/wpa_supplicant.conf ioctl[SIOCSIWPMKSA]: No such device ioctl[SIOCSIWMODE]: No such device Could not configure driver to use managed mode ioctl[SIOCGIFFLAGS]: No such device Could not set interface 'eth0' UP ioctl[SIOCGIWRANGE]: No such device ioctl[SIOCGIFINDEX]: No such device CTRL-EVENT-STATE-CHANGE id=-1 state=0 ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWAUTH]: No such device WEXT auth param 7 value 0x0 - Failed to disable WPA in the driver. ioctl[SIOCSIWAUTH]: No such device WEXT auth param 5 value 0x0 - ioctl[SIOCSIWAUTH]: No such device WEXT auth param 4 value 0x0 - ioctl[SIOCSIWAP]: No such device ioctl[SIOCGIFFLAGS]: No such device # In dmesg we get: <4>[18300.494065] dhd_oob_enable_intr : enable <4>[18305.019976] dhd_net_start failed bus is not ready <4>[18305.020278] dhdsdio_probe: dhd_net_start failed! Do I need to specify the firmware with insmod? Why are we trying to control the interface manually instead of through the Android API? The Android API doesn't support ad-hoc connections as far as I can tell. The card, I am sure, most certainly can.

Read the article
How to set up dual quadro cards on RHEL 5.5?

- by Alex J. Roberts

I have a RHEL 5 workstation with 2 nvidia Quadro FX4500 cards, with one display attached to each card. After doing a clean install of RHEL 5.5, the second display doesnt work (it worked ok in RHEL 5.2). Neither separate X screens nor Xinerama are working. The kernel version is 2.6.18-194.el5 I've tried nvidia drivers 185.18.36 (the ones that i was using on 5.2) and the latest 260.19.36 and neither works. My xorg.conf is as follows: # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 1.0 (buildmeister@builder58) Fri Aug 14 18:34:43 PDT 2009 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 0 0 Screen 1 "Screen1" RightOf "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection Section "Files" FontPath "unix/:7100" EndSection Section "ServerFlags" Option "Xinerama" "1" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/input/mice" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from data in "/etc/sysconfig/keyboard" Identifier "Keyboard0" Driver "kbd" Option "XkbLayout" "us" Option "XkbModel" "pc105" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "DELL 3007WFP" HorizSync 49.3 - 98.5 VertRefresh 60.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor1" VendorName "Unknown" ModelName "DELL 3007WFP" HorizSync 49.3 - 98.5 VertRefresh 60.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro FX 4500" BusID "PCI:10:0:0" EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro FX 4500" BusID "PCI:129:0:0" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection And the Xorg Log: X Window System Version 7.1.1 Release Date: 12 May 2006 X Protocol Version 11, Revision 0, Release 7.1.1 Build Operating System: Linux 2.6.18-164.11.1.el5 x86_64 Red Hat, Inc. Current Operating System: Linux blur.svsdsde 2.6.18-194.el5 #1 SMP Tue Mar 16 21:52:39 EDT 2010 x86_64 Build Date: 06 March 2010 Build ID: xorg-x11-server 1.1.1-48.76.el5 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Module Loader present Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Fri Feb 18 09:52:08 2011 (==) Using config file: "/etc/X11/xorg.conf" (==) ServerLayout "Layout0" (**) |-->Screen "Screen0" (0) (**) | |-->Monitor "Monitor0" (**) | |-->Device "Device0" (**) |-->Screen "Screen1" (1) (**) | |-->Monitor "Monitor1" (**) | |-->Device "Device1" (**) |-->Input Device "Keyboard0" (**) |-->Input Device "Mouse0" (**) FontPath set to: unix/:7100 (==) RgbPath set to "/usr/share/X11/rgb" (==) ModulePath set to "/usr/lib64/xorg/modules" (**) Option "Xinerama" "1" (**) Xinerama: enabled (==) Max clients allowed: 512, resource mask: 0xfffff (II) Open ACPI successful (/var/run/acpid.socket) (II) Module ABI versions: X.Org ANSI C Emulation: 0.3 X.Org Video Driver: 1.0 X.Org XInput driver : 0.6 X.Org Server Extension : 0.3 X.Org Font Renderer : 0.5 (II) Loader running on linux (II) LoadModule: "bitmap" (II) Loading /usr/lib64/xorg/modules/fonts/libbitmap.so (II) Module bitmap: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.0.0 Module class: X.Org Font Renderer ABI class: X.Org Font Renderer, version 0.5 (II) Loading font Bitmap (II) LoadModule: "pcidata" (II) Loading /usr/lib64/xorg/modules/libpcidata.so (II) Module pcidata: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.0.0 ABI class: X.Org Video Driver, version 1.0 (++) using VT number 7 (II) PCI: PCI scan (all values are in hex) (II) PCI: 00:00:0: chip 10de,005e card 103c,1500 rev a3 class 05,80,00 hdr 00 (II) PCI: 00:01:0: chip 10de,0051 card 103c,1500 rev a3 class 06,01,00 hdr 80 (II) PCI: 00:01:1: chip 10de,0052 card 103c,1500 rev a2 class 0c,05,00 hdr 80 (II) PCI: 00:02:0: chip 10de,005a card 103c,1500 rev a2 class 0c,03,10 hdr 80 (II) PCI: 00:02:1: chip 10de,005b card 103c,1500 rev a3 class 0c,03,20 hdr 80 (II) PCI: 00:04:0: chip 10de,0059 card 103c,1500 rev a2 class 04,01,00 hdr 00 (II) PCI: 00:06:0: chip 10de,0053 card 103c,1500 rev f2 class 01,01,8a hdr 00 (II) PCI: 00:07:0: chip 10de,0054 card 103c,1500 rev f3 class 01,01,85 hdr 00 (II) PCI: 00:08:0: chip 10de,0055 card 103c,1500 rev f3 class 01,01,85 hdr 00 (II) PCI: 00:09:0: chip 10de,005c card 0000,0000 rev a2 class 06,04,01 hdr 01 (II) PCI: 00:0a:0: chip 10de,0057 card 103c,1500 rev a3 class 06,80,00 hdr 00 (II) PCI: 00:0e:0: chip 10de,005d card 0000,0000 rev a3 class 06,04,00 hdr 01 (II) PCI: 00:18:0: chip 1022,1100 card 0000,0000 rev 00 class 06,00,00 hdr 80 (II) PCI: 00:18:1: chip 1022,1101 card 0000,0000 rev 00 class 06,00,00 hdr 80 (II) PCI: 00:18:2: chip 1022,1102 card 0000,0000 rev 00 class 06,00,00 hdr 80 (II) PCI: 00:18:3: chip 1022,1103 card 0000,0000 rev 00 class 06,00,00 hdr 80 (II) PCI: 00:19:0: chip 1022,1100 card 0000,0000 rev 00 class 06,00,00 hdr 80 (II) PCI: 00:19:1: chip 1022,1101 card 0000,0000 rev 00 class 06,00,00 hdr 80 (II) PCI: 00:19:2: chip 1022,1102 card 0000,0000 rev 00 class 06,00,00 hdr 80 (II) PCI: 00:19:3: chip 1022,1103 card 0000,0000 rev 00 class 06,00,00 hdr 80 (II) PCI: 05:05:0: chip 104c,8023 card 103c,1500 rev 00 class 0c,00,10 hdr 00 (II) PCI: 0a:00:0: chip 10de,009d card 10de,02af rev a1 class 03,00,00 hdr 00 (II) PCI: End of PCI scan (II) PCI-to-ISA bridge: (II) Bus -1: bridge is at (0:1:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set) (II) Subtractive PCI-to-PCI bridge: (II) Bus 5: bridge is at (0:9:0), (0,5,5), BCTRL: 0x0206 (VGA_EN is cleared) (II) Bus 5 non-prefetchable memory range: [0] -1 0 0xf5000000 - 0xf50fffff (0x100000) MX[B] (II) PCI-to-PCI bridge: (II) Bus 10: bridge is at (0:14:0), (0,10,10), BCTRL: 0x000a (VGA_EN is set) (II) Bus 10 I/O range: [0] -1 0 0x00003000 - 0x00003fff (0x1000) IX[B] (II) Bus 10 non-prefetchable memory range: [0] -1 0 0xf3000000 - 0xf4ffffff (0x2000000) MX[B] (II) Bus 10 prefetchable memory range: [0] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[B] (II) Host-to-PCI bridge: (II) Bus 0: bridge is at (0:24:0), (0,0,10), BCTRL: 0x0008 (VGA_EN is set) (II) Bus 0 I/O range: [0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B] (II) Bus 0 non-prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x100000000) MX[B] (II) Bus 0 prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x100000000) MX[B] (--) PCI:*(10:0:0) nVidia Corporation Quadro FX 4500 rev 161, Mem @ 0xf3000000/24, 0xc0000000/28, 0xf4000000/24, I/O @ 0x3000/7 (II) Addressable bus resource ranges are [0] -1 0 0x00000000 - 0xffffffff (0x100000000) MX[B] [1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B] (II) OS-reported resource ranges: [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [5] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] (II) Active PCI resource ranges: [0] -1 0 0xf5000000 - 0xf5003fff (0x4000) MX[B] [1] -1 0 0xf5004000 - 0xf50047ff (0x800) MX[B] [...snipped... post too long] [28] -1 0 0x0000fb00 - 0x0000fbff (0x100) IX[B] [29] -1 0 0x00003000 - 0x0000307f (0x80) IX[B](B) (II) Active PCI resource ranges after removing overlaps: [0] -1 0 0xf5000000 - 0xf5003fff (0x4000) MX[B] [1] -1 0 0xf5004000 - 0xf50047ff (0x800) MX[B] [...snipped... post too long] [28] -1 0 0x0000fb00 - 0x0000fbff (0x100) IX[B] [29] -1 0 0x00003000 - 0x0000307f (0x80) IX[B](B) (II) OS-reported resource ranges after removing overlaps with PCI: [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [5] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] (II) All system resource ranges: [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [4] -1 0 0xf5000000 - 0xf5003fff (0x4000) MX[B] [5] -1 0 0xf5004000 - 0xf50047ff (0x800) MX[B] [6] -1 0 0xf5104000 - 0xf5104fff (0x1000) MX[B] [7] -1 0 0xf5103000 - 0xf5103fff (0x1000) MX[B] [8] -1 0 0xf5102000 - 0xf5102fff (0x1000) MX[B] [9] -1 0 0xf5101000 - 0xf5101fff (0x1000) MX[B] [10] -1 0 0xfebf0000 - 0xfebf00ff (0x100) MX[B] [11] -1 0 0xf5100000 - 0xf5100fff (0x1000) MX[B] [12] -1 0 0xf4000000 - 0xf4ffffff (0x1000000) MX[B](B) [13] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[B](B) [14] -1 0 0xf3000000 - 0xf3ffffff (0x1000000) MX[B](B) [15] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [16] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [17] -1 0 0x000048f0 - 0x000048f7 (0x8) IX[B] [18] -1 0 0x000048c0 - 0x000048cf (0x10) IX[B] [19] -1 0 0x00004c04 - 0x00004c07 (0x4) IX[B] [20] -1 0 0x000048e8 - 0x000048ef (0x8) IX[B] [21] -1 0 0x00004c00 - 0x00004c03 (0x4) IX[B] [22] -1 0 0x000048e0 - 0x000048e7 (0x8) IX[B] [23] -1 0 0x000048b0 - 0x000048bf (0x10) IX[B] [24] -1 0 0x000048fc - 0x000048ff (0x4) IX[B] [25] -1 0 0x000048d8 - 0x000048df (0x8) IX[B] [26] -1 0 0x000048f8 - 0x000048fb (0x4) IX[B] [27] -1 0 0x000048d0 - 0x000048d7 (0x8) IX[B] [28] -1 0 0x000048a0 - 0x000048af (0x10) IX[B] [29] -1 0 0x00004400 - 0x000044ff (0x100) IX[B] [30] -1 0 0x00004000 - 0x000040ff (0x100) IX[B] [31] -1 0 0x00004840 - 0x0000487f (0x40) IX[B] [32] -1 0 0x00004800 - 0x0000483f (0x40) IX[B] [33] -1 0 0x00004880 - 0x0000489f (0x20) IX[B] [34] -1 0 0x0000fb00 - 0x0000fbff (0x100) IX[B] [35] -1 0 0x00003000 - 0x0000307f (0x80) IX[B](B) (II) LoadModule: "extmod" (II) Loading /usr/lib64/xorg/modules/extensions/libextmod.so (II) Module extmod: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.0.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 0.3 (II) Loading extension SHAPE (II) Loading extension MIT-SUNDRY-NONSTANDARD (II) Loading extension BIG-REQUESTS (II) Loading extension SYNC (II) Loading extension MIT-SCREEN-SAVER (II) Loading extension XC-MISC (II) Loading extension XFree86-VidModeExtension (II) Loading extension XFree86-Misc (II) Loading extension XFree86-DGA (II) Loading extension DPMS (II) Loading extension TOG-CUP (II) Loading extension Extended-Visual-Information (II) Loading extension XVideo (II) Loading extension XVideo-MotionCompensation (II) Loading extension X-Resource (II) LoadModule: "dbe" (II) Loading /usr/lib64/xorg/modules/extensions/libdbe.so (II) Module dbe: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.0.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 0.3 (II) Loading extension DOUBLE-BUFFER (II) LoadModule: "glx" (II) Loading /usr/lib64/xorg/modules/extensions/libglx.so (II) Module glx: vendor="NVIDIA Corporation" compiled for 4.0.2, module version = 1.0.0 Module class: X.Org Server Extension (II) NVIDIA GLX Module 185.18.36 Fri Aug 14 18:27:24 PDT 2009 (II) Loading extension GLX (II) LoadModule: "freetype" (II) Loading /usr/lib64/xorg/modules/fonts/libfreetype.so (II) Module freetype: vendor="X.Org Foundation & the After X-TT Project" compiled for 7.1.1, module version = 2.1.0 Module class: X.Org Font Renderer ABI class: X.Org Font Renderer, version 0.5 (II) Loading font FreeType (II) LoadModule: "type1" (II) Loading /usr/lib64/xorg/modules/fonts/libtype1.so (II) Module type1: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.0.2 Module class: X.Org Font Renderer ABI class: X.Org Font Renderer, version 0.5 (II) Loading font Type1 (II) LoadModule: "record" (II) Loading /usr/lib64/xorg/modules/extensions/librecord.so (II) Module record: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.13.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 0.3 (II) Loading extension RECORD (II) LoadModule: "dri" (II) Loading /usr/lib64/xorg/modules/extensions/libdri.so (II) Module dri: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.0.0 ABI class: X.Org Server Extension, version 0.3 (II) Loading sub module "drm" (II) LoadModule: "drm" (II) Loading /usr/lib64/xorg/modules/linux/libdrm.so (II) Module drm: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.0.0 ABI class: X.Org Server Extension, version 0.3 (II) Loading extension XFree86-DRI (II) LoadModule: "nvidia" (II) Loading /usr/lib64/xorg/modules/drivers/nvidia_drv.so (II) Module nvidia: vendor="NVIDIA Corporation" compiled for 4.0.2, module version = 1.0.0 Module class: X.Org Video Driver (II) LoadModule: "kbd" (II) Loading /usr/lib64/xorg/modules/input/kbd_drv.so (II) Module kbd: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.1.0 Module class: X.Org XInput Driver ABI class: X.Org XInput driver, version 0.6 (II) LoadModule: "mouse" (II) Loading /usr/lib64/xorg/modules/input/mouse_drv.so (II) Module mouse: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.1.1 Module class: X.Org XInput Driver ABI class: X.Org XInput driver, version 0.6 (II) NVIDIA dlloader X Driver 185.18.36 Fri Aug 14 17:51:02 PDT 2009 (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs (II) Primary Device is: PCI 0a:00:0 (--) Chipset NVIDIA GPU found (II) Loading sub module "fb" (II) LoadModule: "fb" (II) Loading /usr/lib64/xorg/modules/libfb.so (II) Module fb: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.0.0 ABI class: X.Org ANSI C Emulation, version 0.3 (II) Loading sub module "wfb" (II) LoadModule: "wfb" (II) Loading /usr/lib64/xorg/modules/libwfb.so (II) Module wfb: vendor="NVIDIA Corporation" compiled for 7.1.99.2, module version = 1.0.0 (II) Loading sub module "ramdac" (II) LoadModule: "ramdac" (II) Loading /usr/lib64/xorg/modules/libramdac.so (II) Module ramdac: vendor="X.Org Foundation" compiled for 7.1.1, module version = 0.1.0 ABI class: X.Org Video Driver, version 1.0 (II) resource ranges after xf86ClaimFixedResources() call: [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [4] -1 0 0xf5000000 - 0xf5003fff (0x4000) MX[B] [5] -1 0 0xf5004000 - 0xf50047ff (0x800) MX[B] [6] -1 0 0xf5104000 - 0xf5104fff (0x1000) MX[B] [7] -1 0 0xf5103000 - 0xf5103fff (0x1000) MX[B] [8] -1 0 0xf5102000 - 0xf5102fff (0x1000) MX[B] [9] -1 0 0xf5101000 - 0xf5101fff (0x1000) MX[B] [10] -1 0 0xfebf0000 - 0xfebf00ff (0x100) MX[B] [11] -1 0 0xf5100000 - 0xf5100fff (0x1000) MX[B] [12] -1 0 0xf4000000 - 0xf4ffffff (0x1000000) MX[B](B) [13] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[B](B) [14] -1 0 0xf3000000 - 0xf3ffffff (0x1000000) MX[B](B) [15] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [16] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [17] -1 0 0x000048f0 - 0x000048f7 (0x8) IX[B] [18] -1 0 0x000048c0 - 0x000048cf (0x10) IX[B] [19] -1 0 0x00004c04 - 0x00004c07 (0x4) IX[B] [20] -1 0 0x000048e8 - 0x000048ef (0x8) IX[B] [21] -1 0 0x00004c00 - 0x00004c03 (0x4) IX[B] [22] -1 0 0x000048e0 - 0x000048e7 (0x8) IX[B] [23] -1 0 0x000048b0 - 0x000048bf (0x10) IX[B] [24] -1 0 0x000048fc - 0x000048ff (0x4) IX[B] [25] -1 0 0x000048d8 - 0x000048df (0x8) IX[B] [26] -1 0 0x000048f8 - 0x000048fb (0x4) IX[B] [27] -1 0 0x000048d0 - 0x000048d7 (0x8) IX[B] [28] -1 0 0x000048a0 - 0x000048af (0x10) IX[B] [29] -1 0 0x00004400 - 0x000044ff (0x100) IX[B] [30] -1 0 0x00004000 - 0x000040ff (0x100) IX[B] [31] -1 0 0x00004840 - 0x0000487f (0x40) IX[B] [32] -1 0 0x00004800 - 0x0000483f (0x40) IX[B] [33] -1 0 0x00004880 - 0x0000489f (0x20) IX[B] [34] -1 0 0x0000fb00 - 0x0000fbff (0x100) IX[B] [35] -1 0 0x00003000 - 0x0000307f (0x80) IX[B](B) (II) resource ranges after probing: [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [4] -1 0 0xf5000000 - 0xf5003fff (0x4000) MX[B] [5] -1 0 0xf5004000 - 0xf50047ff (0x800) MX[B] [6] -1 0 0xf5104000 - 0xf5104fff (0x1000) MX[B] [7] -1 0 0xf5103000 - 0xf5103fff (0x1000) MX[B] [8] -1 0 0xf5102000 - 0xf5102fff (0x1000) MX[B] [9] -1 0 0xf5101000 - 0xf5101fff (0x1000) MX[B] [10] -1 0 0xfebf0000 - 0xfebf00ff (0x100) MX[B] [11] -1 0 0xf5100000 - 0xf5100fff (0x1000) MX[B] [12] -1 0 0xf4000000 - 0xf4ffffff (0x1000000) MX[B](B) [13] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[B](B) [14] -1 0 0xf3000000 - 0xf3ffffff (0x1000000) MX[B](B) [15] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B] [16] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B] [17] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B] [18] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [19] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [20] -1 0 0x000048f0 - 0x000048f7 (0x8) IX[B] [21] -1 0 0x000048c0 - 0x000048cf (0x10) IX[B] [22] -1 0 0x00004c04 - 0x00004c07 (0x4) IX[B] [23] -1 0 0x000048e8 - 0x000048ef (0x8) IX[B] [24] -1 0 0x00004c00 - 0x00004c03 (0x4) IX[B] [25] -1 0 0x000048e0 - 0x000048e7 (0x8) IX[B] [26] -1 0 0x000048b0 - 0x000048bf (0x10) IX[B] [27] -1 0 0x000048fc - 0x000048ff (0x4) IX[B] [28] -1 0 0x000048d8 - 0x000048df (0x8) IX[B] [29] -1 0 0x000048f8 - 0x000048fb (0x4) IX[B] [30] -1 0 0x000048d0 - 0x000048d7 (0x8) IX[B] [31] -1 0 0x000048a0 - 0x000048af (0x10) IX[B] [32] -1 0 0x00004400 - 0x000044ff (0x100) IX[B] [33] -1 0 0x00004000 - 0x000040ff (0x100) IX[B] [34] -1 0 0x00004840 - 0x0000487f (0x40) IX[B] [35] -1 0 0x00004800 - 0x0000483f (0x40) IX[B] [36] -1 0 0x00004880 - 0x0000489f (0x20) IX[B] [37] -1 0 0x0000fb00 - 0x0000fbff (0x100) IX[B] [38] -1 0 0x00003000 - 0x0000307f (0x80) IX[B](B) [39] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B] [40] 0 0 0x000003c0 - 0x000003df (0x20) IS[B] (II) Setting vga for screen 0. (**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32 (==) NVIDIA(0): RGB weight 888 (==) NVIDIA(0): Default visual is TrueColor (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0) (**) NVIDIA(0): Option "TwinView" "0" (**) NVIDIA(0): Option "MetaModes" "nvidia-auto-select +0+0" (**) NVIDIA(0): Enabling RENDER acceleration (II) NVIDIA(0): Support for GLX with the Damage and Composite X extensions is (II) NVIDIA(0): enabled. (II) NVIDIA(0): NVIDIA GPU Quadro FX 4500 (G70GL) at PCI:10:0:0 (GPU-0) (--) NVIDIA(0): Memory: 524288 kBytes (--) NVIDIA(0): VideoBIOS: 05.70.02.41.01 (II) NVIDIA(0): Detected PCI Express Link width: 16X (--) NVIDIA(0): Interlaced video modes are supported on this GPU (--) NVIDIA(0): Connected display device(s) on Quadro FX 4500 at PCI:10:0:0: (--) NVIDIA(0): DELL 3007WFP (DFP-0) (--) NVIDIA(0): DELL 3007WFP (DFP-0): 310.0 MHz maximum pixel clock (--) NVIDIA(0): DELL 3007WFP (DFP-0): Internal Dual Link TMDS (II) NVIDIA(0): Assigned Display Device: DFP-0 (II) NVIDIA(0): Validated modes: (II) NVIDIA(0): "nvidia-auto-select+0+0" (II) NVIDIA(0): Virtual screen size determined to be 2560 x 1600 (--) NVIDIA(0): DPI set to (101, 101); computed from "UseEdidDpi" X config (--) NVIDIA(0): option (WW) NVIDIA(0): UBB is incompatible with the Composite extension. Disabling (WW) NVIDIA(0): UBB. (==) NVIDIA(0): Disabling 32-bit ARGB GLX visuals. (--) Depth 24 pixmap format is 32 bpp (II) do I need RAC? No, I don't. (II) resource ranges after preInit: [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [4] -1 0 0xf5000000 - 0xf5003fff (0x4000) MX[B] [5] -1 0 0xf5004000 - 0xf50047ff (0x800) MX[B] [6] -1 0 0xf5104000 - 0xf5104fff (0x1000) MX[B] [7] -1 0 0xf5103000 - 0xf5103fff (0x1000) MX[B] [8] -1 0 0xf5102000 - 0xf5102fff (0x1000) MX[B] [9] -1 0 0xf5101000 - 0xf5101fff (0x1000) MX[B] [10] -1 0 0xfebf0000 - 0xfebf00ff (0x100) MX[B] [11] -1 0 0xf5100000 - 0xf5100fff (0x1000) MX[B] [12] -1 0 0xf4000000 - 0xf4ffffff (0x1000000) MX[B](B) [13] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[B](B) [14] -1 0 0xf3000000 - 0xf3ffffff (0x1000000) MX[B](B) [15] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B] [16] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B] [17] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B] [18] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [19] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [20] -1 0 0x000048f0 - 0x000048f7 (0x8) IX[B] [21] -1 0 0x000048c0 - 0x000048cf (0x10) IX[B] [22] -1 0 0x00004c04 - 0x00004c07 (0x4) IX[B] [23] -1 0 0x000048e8 - 0x000048ef (0x8) IX[B] [24] -1 0 0x00004c00 - 0x00004c03 (0x4) IX[B] [25] -1 0 0x000048e0 - 0x000048e7 (0x8) IX[B] [26] -1 0 0x000048b0 - 0x000048bf (0x10) IX[B] [27] -1 0 0x000048fc - 0x000048ff (0x4) IX[B] [28] -1 0 0x000048d8 - 0x000048df (0x8) IX[B] [29] -1 0 0x000048f8 - 0x000048fb (0x4) IX[B] [30] -1 0 0x000048d0 - 0x000048d7 (0x8) IX[B] [31] -1 0 0x000048a0 - 0x000048af (0x10) IX[B] [32] -1 0 0x00004400 - 0x000044ff (0x100) IX[B] [33] -1 0 0x00004000 - 0x000040ff (0x100) IX[B] [34] -1 0 0x00004840 - 0x0000487f (0x40) IX[B] [35] -1 0 0x00004800 - 0x0000483f (0x40) IX[B] [36] -1 0 0x00004880 - 0x0000489f (0x20) IX[B] [37] -1 0 0x0000fb00 - 0x0000fbff (0x100) IX[B] [38] -1 0 0x00003000 - 0x0000307f (0x80) IX[B](B) [39] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B] [40] 0 0 0x000003c0 - 0x000003df (0x20) IS[B] (II) NVIDIA(GPU-1): NVIDIA GPU Quadro FX 4500 (G70GL) at PCI:129:0:0 (GPU-1) (--) NVIDIA(GPU-1): Memory: 524288 kBytes (--) NVIDIA(GPU-1): VideoBIOS: 05.70.02.41.01 (II) NVIDIA(GPU-1): Detected PCI Express Link width: 16X (--) NVIDIA(GPU-1): Interlaced video modes are supported on this GPU (--) NVIDIA(GPU-1): Connected display device(s) on Quadro FX 4500 at PCI:129:0:0: (--) NVIDIA(GPU-1): DELL 3007WFP (DFP-0) (--) NVIDIA(GPU-1): DELL 3007WFP (DFP-0): 310.0 MHz maximum pixel clock (--) NVIDIA(GPU-1): DELL 3007WFP (DFP-0): Internal Dual Link TMDS (II) NVIDIA(0): Initialized GPU GART. (II) NVIDIA(0): Setting mode "nvidia-auto-select+0+0" (II) Loading extension NV-GLX (II) NVIDIA(0): NVIDIA 3D Acceleration Architecture Initialized (==) NVIDIA(0): Disabling shared memory pixmaps (II) NVIDIA(0): Using the NVIDIA 2D acceleration architecture (==) NVIDIA(0): Backing store disabled (==) NVIDIA(0): Silken mouse enabled (**) Option "dpms" (**) NVIDIA(0): DPMS enabled (II) Loading extension NV-CONTROL (==) RandR enabled (II) Setting vga for screen 0. (II) Initializing built-in extension MIT-SHM (II) Initializing built-in extension XInputExtension (II) Initializing built-in extension XTEST (II) Initializing built-in extension XKEYBOARD (II) Initializing built-in extension XC-APPGROUP (II) Initializing built-in extension SECURITY (II) Initializing built-in extension XINERAMA (II) Initializing built-in extension XFIXES (II) Initializing built-in extension XFree86-Bigfont (II) Initializing built-in extension RENDER (II) Initializing built-in extension RANDR (II) Initializing built-in extension COMPOSITE (II) Initializing built-in extension DAMAGE (II) Initializing built-in extension XEVIE (II) Initializing extension GLX (WW) Disabling Composite since Xinerama is enabled (**) Option "CoreKeyboard" (**) Keyboard0: Core Keyboard (**) Option "Protocol" "standard" (**) Keyboard0: Protocol: standard (**) Option "AutoRepeat" "500 30" (**) Option "XkbRules" "xorg" (**) Keyboard0: XkbRules: "xorg" (**) Option "XkbModel" "pc105" (**) Keyboard0: XkbModel: "pc105" (**) Option "XkbLayout" "us" (**) Keyboard0: XkbLayout: "us" (**) Option "CustomKeycodes" "off" (**) Keyboard0: CustomKeycodes disabled (**) Option "Protocol" "auto" (**) Mouse0: Device: "/dev/input/mice" (**) Mouse0: Protocol: "auto" (**) Option "CorePointer" (**) Mouse0: Core Pointer (**) Option "Device" "/dev/input/mice" (**) Option "Emulate3Buttons" "no" (**) Option "ZAxisMapping" "4 5" (**) Mouse0: ZAxisMapping: buttons 4 and 5 (**) Mouse0: Buttons: 9 (II) XINPUT: Adding extended input device "Mouse0" (type: MOUSE) (II) XINPUT: Adding extended input device "Keyboard0" (type: KEYBOARD) (--) Mouse0: PnP-detected protocol: "ExplorerPS/2" (II) Mouse0: ps2EnableDataReporting: succeeded (II) Open ACPI successful (/var/run/acpid.socket) (II) NVIDIA(0): Setting mode "nvidia-auto-select+0+0" (II) Mouse0: ps2EnableDataReporting: succeeded (the snipped part can be changed if necessary) Any help at all would be appreciated. Cheers, Alex

Read the article
Secure ldap problem

- by neverland

Hi there, I have tried to config my openldap to have secure connection by using openssl on Debian5. By the way, I got trouble during the below command. ldap:/etc/ldap# slapd -h 'ldap:// ldaps://' -d1 >>> slap_listener(ldaps://) connection_get(15): got connid=7 connection_read(15): checking for input on id=7 connection_get(15): got connid=7 connection_read(15): checking for input on id=7 connection_get(15): got connid=7 connection_read(15): checking for input on id=7 connection_get(15): got connid=7 connection_read(15): checking for input on id=7 connection_read(15): unable to get TLS client DN, error=49 id=7 connection_get(15): got connid=7 connection_read(15): checking for input on id=7 ber_get_next ber_get_next on fd 15 failed errno=0 (Success) connection_closing: readying conn=7 sd=15 for close connection_close: conn=7 sd=15 Then I have search for "unable to get TLS client DN, error=49 id=7" but it seems no where has a good solution to this yet. Please help. Thanks # Well, I try to fix something to get it work but now I got this ldap:~# slapd -d 256 -f /etc/openldap/slapd.conf @(#) $OpenLDAP: slapd 2.4.11 (Nov 26 2009 09:17:06) $ root@SD6-Casa:/tmp/buildd/openldap-2.4.11/debian/build/servers/slapd could not stat config file "/etc/openldap/slapd.conf": No such file or directory (2) slapd stopped. connections_destroy: nothing to destroy. What should I do now? log : ldap:~# /etc/init.d/slapd start Starting OpenLDAP: slapd - failed. The operation failed but no output was produced. For hints on what went wrong please refer to the system's logfiles (e.g. /var/log/syslog) or try running the daemon in Debug mode like via "slapd -d 16383" (warning: this will create copious output). Below, you can find the command line options used by this script to run slapd. Do not forget to specify those options if you want to look to debugging output: slapd -h 'ldaps:///' -g openldap -u openldap -f /etc/ldap/slapd.conf ldap:~# tail /var/log/messages Feb 8 16:53:27 ldap kernel: [ 123.582757] intel8x0_measure_ac97_clock: measured 57614 usecs Feb 8 16:53:27 ldap kernel: [ 123.582801] intel8x0: measured clock 172041 rejected Feb 8 16:53:27 ldap kernel: [ 123.582825] intel8x0: clocking to 48000 Feb 8 16:53:27 ldap kernel: [ 131.469687] Adding 240932k swap on /dev/hda5. Priority:-1 extents:1 across:240932k Feb 8 16:53:27 ldap kernel: [ 133.432131] EXT3 FS on hda1, internal journal Feb 8 16:53:27 ldap kernel: [ 135.478218] loop: module loaded Feb 8 16:53:27 ldap kernel: [ 141.348104] eth0: link up, 100Mbps, full-duplex Feb 8 16:53:27 ldap rsyslogd: [origin software="rsyslogd" swVersion="3.18.6" x-pid="1705" x-info="http://www.rsyslog.com"] restart Feb 8 16:53:34 ldap kernel: [ 159.217171] NET: Registered protocol family 10 Feb 8 16:53:34 ldap kernel: [ 159.220083] lo: Disabled Privacy Extensions

Read the article
Weird random application hang problem

- by haridsv

I am trying to understand an application hang problem that started up lately on my windows xp system. The system runs fine for days (sometimes) without ever shutting down or putting it to sleep, but the problem first shows up as one of the apps hanging. The application's UI stops responding or one or more background threads hang, so even though the GUI is responding, it is not doing anything (e.g., in VirtualDub's case, the UI responds fine, but the job doesn't progress and I won't even be able to abort it). The weirdness part comes from the fact that if I try to kill such an app, the program that is used to kill it goes into the same mode (i.e, that hangs instead of the original). E.g., if I use Process Explorer to kill it, the original program exits, but procexp now hangs. If I use another instance of procexp to kill the one that is hanging, this repeats, so there is always at least one program hanging in that state. This is not specific to procexp, I tried the native task manager and even the "End Process" dialog from windows explorer that shows up when you try to close a non-responsive GUI (in this case, the explorer itself hangs). The only program that didn't hang after the kill, is the command line taskkill. However, in this case, explorer hangs instead of taskkill. Also, once this problem starts manifesting, it soon ends up freezing the whole system to the extent that even a clean shutdown is not possible, so I have learned to reboot as soon as I notice this problem, however this is very inconvenient, as I often have encoding batch jobs going on which can't continue the job after the restart. The longer I leave the system running after seeing this problem, the more applications get into this state. I have tried to do a repair install but that didn't make any difference. I also uninstalled some of the newer installs, but again no difference. I tried to search online, but got inundating results for generic hang and crash related problems. Though I couldn't notice any pattern, it seems as though the problem is more frequent if I have some video encoding going on at that time. I had the system running for days when I only do browsing and internet audio/video chat before I decide to start encoding something and the problem starts to show up. I am not too sure if it is the encoding program that first hangs, though I almost always noticed that too hanging (like the VirtualDub stopping to make progress). I also had to reboot 3 times on one day when I was heavily experimenting with encoding. I would appreciate any help in narrowing down this problem and save me the trouble of reinstalling. I don't especially want to loose my gotd installs.

Read the article
Puppet - Possible to use software design patterns in modules?

- by Mike Purcell

As I work with puppet, I find myself wanting to automate more complex setups, for example vhosts for X number of websites. As my puppet manifests get more complex I find it difficult to apply the DRY (don't repeat yourself) principle. Below is a simplified snippet of what I am after, but doesn't work because puppet throws various errors depending up whether I use classes or defines. I'd like to get some feed back from some seasoned puppetmasters on how they might approach this solution. # site.pp import 'nodes' # nodes.pp node nodes_dev { $service_env = 'dev' } node nodes_prod { $service_env = 'prod' } import 'nodes/dev' import 'nodes/prod' # nodes/dev.pp node 'service1.ownij.lan' inherits nodes_dev { httpd::vhost::package::site { 'foo': } httpd::vhost::package::site { 'bar': } } # modules/vhost/package.pp class httpd::vhost::package { class manage($port) { # More complex stuff goes here like ensuring that conf paths and uris exist # As well as log files, which is I why I want to do the work once and use many notify { $service_env: } notify { $port: } } define site { case $name { 'foo': { class 'httpd::vhost::package::manage': port => 20000 } } 'bar': { class 'httpd::vhost::package::manage': port => 20001 } } } } } That code snippet gives me a Duplicate declaration: Class[Httpd::Vhost::Package::Manage] error, and if I switch the manage class to a define, and attempt to access a global or pass in a variable common to both foo and bar, I get a Duplicate declaration: Notify[dev] error. Any suggestions how I can implement the DRY principle and still get puppet to work? -- UPDATE -- I'm still having a problem trying to ensure that some of my vhosts, which may share a parent directory, are setup correctly. Something like this: node 'service1.ownij.lan' inherits nodes_dev { httpd::vhost::package::site { 'foo_sitea': } httpd::vhost::package::site { 'foo_siteb': } httpd::vhost::package::site { 'bar': } } What I need to happen is that sitea and siteb have the same parent "foo" folder. The problem I am having is when I call a define to ensure the "foo" folder exists. Below is the site define as I have it, hopefully it will make sense what I am trying to accomplish. class httpd::vhost::package { File { owner => root, group => root, mode => 0660 } define site() { $app_parts = split($name, '[_]') $app_primary = $app_parts[0] if ($app_parts[1] == '') { $tpl_path_partial_app = "${app_primary}" $app_sub = '' } else { $tpl_path_partial_app = "${app_primary}/${app_parts[1]}" $app_sub = $app_parts[1] } include httpd::vhost::log::base httpd::vhost::log::app { $name: app_primary => $app_primary, app_sub => $app_sub } } } class httpd::vhost::log { class base { $paths = [ '/tmp', '/tmp/var', '/tmp/var/log', '/tmp/var/log/httpd', "/tmp/var/log/httpd/${service_env}" ] file { $paths: ensure => directory } } define app($app_primary, $app_sub) { $paths = [ "/tmp/var/log/httpd/${service_env}/${app_primary}", "/tmp/var/log/httpd/${service_env}/${app_primary}/${app_sub}" ] file { $paths: ensure => directory } } } The include httpd::vhost::log::base works fine, because it is "included", which means it is only implemented once, even though site is called multiple times. The error I am getting is: Duplicate declaration: File[/tmp/var/log/httpd/dev/foo]. I looked into using exec, but not sure this is the correct route, surely others have had to deal with this before and any insight is appreciated as I have been grappling with this for a few weeks. Thanks.

Read the article
Ubuntu hard disk problem

- by Henadzy

Hello! I have got the error with a hard disk on Ubuntu 9.10. It slows down my system, applications have not been responding for a long time. But when I mount and use filesystem which placed on this hard disk at other computer it works properly. disk: SAMSUNG HD161HJ (SATA) syslog: Apr 25 00:28:25 vare6gin kernel: [ 885.773839] ata3.00: exception Emask 0x1 SAct 0x1e SErr 0x0 action 0x6 frozen Apr 25 00:28:25 vare6gin kernel: [ 885.773845] ata3.00: Ata error. fis:0x21 Apr 25 00:28:25 vare6gin kernel: [ 885.773861] ata3.00: cmd 60/08:08:3f:00:ad/00:00:10:00:00/40 tag 1 ncq 4096 in Apr 25 00:28:25 vare6gin kernel: [ 885.773864] res 51/40:24:67:c8:91/40:00:05:00:00/40 Emask 0x9 (media error) Apr 25 00:28:25 vare6gin kernel: [ 885.773871] ata3.00: status: { DRDY ERR } Apr 25 00:28:25 vare6gin kernel: [ 885.773877] ata3.00: error: { UNC } Apr 25 00:28:25 vare6gin kernel: [ 885.773890] ata3.00: cmd 60/18:10:9f:6b:ed/00:00:0e:00:00/40 tag 2 ncq 12288 in Apr 25 00:28:25 vare6gin kernel: [ 885.773893] res 51/40:24:67:c8:91/40:00:05:00:00/40 Emask 0x9 (media error) Apr 25 00:28:25 vare6gin kernel: [ 885.773900] ata3.00: status: { DRDY ERR } Apr 25 00:28:25 vare6gin kernel: [ 885.773904] ata3.00: error: { UNC } Apr 25 00:28:25 vare6gin kernel: [ 885.773918] ata3.00: cmd 60/08:18:3f:5f:ed/00:00:0e:00:00/40 tag 3 ncq 4096 in Apr 25 00:28:25 vare6gin kernel: [ 885.773921] res 51/40:24:67:c8:91/40:00:05:00:00/40 Emask 0x9 (media error) Apr 25 00:28:25 vare6gin kernel: [ 885.773927] ata3.00: status: { DRDY ERR } Apr 25 00:28:25 vare6gin kernel: [ 885.773932] ata3.00: error: { UNC } Apr 25 00:28:25 vare6gin kernel: [ 885.773946] ata3.00: cmd 60/08:20:67:c8:91/00:00:05:00:00/40 tag 4 ncq 4096 in Apr 25 00:28:25 vare6gin kernel: [ 885.773948] res 51/40:24:67:c8:91/40:00:05:00:00/40 Emask 0x9 (media error) Apr 25 00:28:25 vare6gin kernel: [ 885.773955] ata3.00: status: { DRDY ERR } Apr 25 00:28:25 vare6gin kernel: [ 885.773960] ata3.00: error: { UNC } Apr 25 00:28:25 vare6gin kernel: [ 885.773970] ata3: hard resetting link Apr 25 00:28:25 vare6gin kernel: [ 885.773974] ata3: nv: skipping hardreset on occupied port Apr 25 00:28:25 vare6gin kernel: [ 886.240073] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Apr 25 00:28:25 vare6gin kernel: [ 886.256277] ata3.00: configured for UDMA/133 Apr 25 00:28:25 vare6gin kernel: [ 886.256305] ata3: EH complete Apr 25 00:28:27 vare6gin kernel: [ 888.176088] ata3: EH in SWNCQ mode,QC:qc_active 0xF sactive 0xF Apr 25 00:28:27 vare6gin kernel: [ 888.176099] ata3: SWNCQ:qc_active 0xF defer_bits 0x0 last_issue_tag 0x3 Apr 25 00:28:27 vare6gin kernel: [ 888.176102] dhfis 0xF dmafis 0x1 sdbfis 0x0 Apr 25 00:28:27 vare6gin kernel: [ 888.176109] ata3: ATA_REG 0x51 ERR_REG 0x40 Apr 25 00:28:27 vare6gin kernel: [ 888.176113] ata3: tag : dhfis dmafis sdbfis sacitve Apr 25 00:28:27 vare6gin kernel: [ 888.176120] ata3: tag 0x0: 1 1 0 1 Apr 25 00:28:27 vare6gin kernel: [ 888.176126] ata3: tag 0x1: 1 0 0 1 Apr 25 00:28:27 vare6gin kernel: [ 888.176131] ata3: tag 0x2: 1 0 0 1 Apr 25 00:28:27 vare6gin kernel: [ 888.176136] ata3: tag 0x3: 1 0 0 1

Read the article
Ubuntu hard disk problem

- by Henadzy

Hello! I have got the error with a hard disk on Ubuntu 9.10. It slows down my system, applications have not been responding for a long time. But when I mount and use filesystem which placed on this hard disk at other computer it works properly. disk: SAMSUNG HD161HJ (SATA) syslog: Apr 25 00:28:25 vare6gin kernel: [ 885.773839] ata3.00: exception Emask 0x1 SAct 0x1e SErr 0x0 action 0x6 frozen Apr 25 00:28:25 vare6gin kernel: [ 885.773845] ata3.00: Ata error. fis:0x21 Apr 25 00:28:25 vare6gin kernel: [ 885.773861] ata3.00: cmd 60/08:08:3f:00:ad/00:00:10:00:00/40 tag 1 ncq 4096 in Apr 25 00:28:25 vare6gin kernel: [ 885.773864] res 51/40:24:67:c8:91/40:00:05:00:00/40 Emask 0x9 (media error) Apr 25 00:28:25 vare6gin kernel: [ 885.773871] ata3.00: status: { DRDY ERR } Apr 25 00:28:25 vare6gin kernel: [ 885.773877] ata3.00: error: { UNC } Apr 25 00:28:25 vare6gin kernel: [ 885.773890] ata3.00: cmd 60/18:10:9f:6b:ed/00:00:0e:00:00/40 tag 2 ncq 12288 in Apr 25 00:28:25 vare6gin kernel: [ 885.773893] res 51/40:24:67:c8:91/40:00:05:00:00/40 Emask 0x9 (media error) Apr 25 00:28:25 vare6gin kernel: [ 885.773900] ata3.00: status: { DRDY ERR } Apr 25 00:28:25 vare6gin kernel: [ 885.773904] ata3.00: error: { UNC } Apr 25 00:28:25 vare6gin kernel: [ 885.773918] ata3.00: cmd 60/08:18:3f:5f:ed/00:00:0e:00:00/40 tag 3 ncq 4096 in Apr 25 00:28:25 vare6gin kernel: [ 885.773921] res 51/40:24:67:c8:91/40:00:05:00:00/40 Emask 0x9 (media error) Apr 25 00:28:25 vare6gin kernel: [ 885.773927] ata3.00: status: { DRDY ERR } Apr 25 00:28:25 vare6gin kernel: [ 885.773932] ata3.00: error: { UNC } Apr 25 00:28:25 vare6gin kernel: [ 885.773946] ata3.00: cmd 60/08:20:67:c8:91/00:00:05:00:00/40 tag 4 ncq 4096 in Apr 25 00:28:25 vare6gin kernel: [ 885.773948] res 51/40:24:67:c8:91/40:00:05:00:00/40 Emask 0x9 (media error) Apr 25 00:28:25 vare6gin kernel: [ 885.773955] ata3.00: status: { DRDY ERR } Apr 25 00:28:25 vare6gin kernel: [ 885.773960] ata3.00: error: { UNC } Apr 25 00:28:25 vare6gin kernel: [ 885.773970] ata3: hard resetting link Apr 25 00:28:25 vare6gin kernel: [ 885.773974] ata3: nv: skipping hardreset on occupied port Apr 25 00:28:25 vare6gin kernel: [ 886.240073] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Apr 25 00:28:25 vare6gin kernel: [ 886.256277] ata3.00: configured for UDMA/133 Apr 25 00:28:25 vare6gin kernel: [ 886.256305] ata3: EH complete Apr 25 00:28:27 vare6gin kernel: [ 888.176088] ata3: EH in SWNCQ mode,QC:qc_active 0xF sactive 0xF Apr 25 00:28:27 vare6gin kernel: [ 888.176099] ata3: SWNCQ:qc_active 0xF defer_bits 0x0 last_issue_tag 0x3 Apr 25 00:28:27 vare6gin kernel: [ 888.176102] dhfis 0xF dmafis 0x1 sdbfis 0x0 Apr 25 00:28:27 vare6gin kernel: [ 888.176109] ata3: ATA_REG 0x51 ERR_REG 0x40 Apr 25 00:28:27 vare6gin kernel: [ 888.176113] ata3: tag : dhfis dmafis sdbfis sacitve Apr 25 00:28:27 vare6gin kernel: [ 888.176120] ata3: tag 0x0: 1 1 0 1 Apr 25 00:28:27 vare6gin kernel: [ 888.176126] ata3: tag 0x1: 1 0 0 1 Apr 25 00:28:27 vare6gin kernel: [ 888.176131] ata3: tag 0x2: 1 0 0 1 Apr 25 00:28:27 vare6gin kernel: [ 888.176136] ata3: tag 0x3: 1 0 0 1

Read the article
Blank Page: wordpress on nginx+php-fpm

- by troutwine

Good day. While this post discusses a similar setup to mine serving blank pages occasionally after having made a successful installation, I am unable to serve anything but blank pages. My setup: Wordpress 3.0.4 nginx 0.8.54 php-fpm 5.3.5 (fpm-fcgi) Arch Linux Configuration Files php-fpm.conf: [global] pid = run/php-fpm/php-fpm.pid error_log = log/php-fpm.log log_level = notice [www] listen = 127.0.0.1:9000 listen.owner = www listen.group = www listen.mode = 0660 user = www group = www pm = dynamic pm.max_children = 50 pm.start_servers = 20 pm.min_spare_servers = 5 pm.max_spare_servers = 35 pm.max_requests = 500 nginx.conf: user www; worker_processes 1; error_log /var/log/nginx/error.log notice; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; sendfile on; keepalive_timeout 65; gzip on; include /etc/nginx/sites-enabled/*.conf; } /etc/nginx/sites-enabled/blog_sharonrhodes_us.conf: upstream php { server 127.0.0.1:9000; } server { error_log /var/log/nginx/us/sharonrhodes/blog/error.log notice; access_log /var/log/nginx/us/sharonrhodes/blog/access.log; server_name blog.sharonrhodes.us; root /srv/apps/us/sharonrhodes/blog; index index.php; location = /favicon.ico { log_not_found off; access_log off; } location = /robots.txt { allow all; log_not_found off; access_log off; } location / { # This is cool because no php is touched for static content try_files $uri $uri/ /index.php?q=$uri&$args; } location ~ \.php$ { fastcgi_split_path_info ^(.+\.php)(/.+)$; #NOTE: You should have "cgi.fix_pathinfo = 0;" in php.ini include fastcgi_params; fastcgi_intercept_errors on; fastcgi_pass php; } location ~* \.(js|css|png|jpg|jpeg|gif|ico)$ { expires max; log_not_found off; } }

Read the article
Network Bridging for WiFi-to-Ethernet in linux

- by shakaran

It is possible Network Bridging for WiFi-to-Ethernet in linux instead of Ethernet-to-Ethernet? I have a CentOS 6.3 machine. I am using KVM and I want perform a brigde for virtualize more machines. This machine is connected only via wireless connection and it doesn't have a ethernet connection. So, I did a bridge over the WiFi interface like: # cat /etc/sysconfig/network-scripts/ifcfg-br0 DEVICE="br0" NM_CONTROLLED="yes" ONBOOT=yes TYPE=Bridge BOOTPROTO=none IPADDR=192.168.1.50 PREFIX=24 GATEWAY=192.168.1.1 DNS1=8.8.8.8 DNS2=8.8.4.4 DEFROUTE=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no NAME="System br0" Then I edit my wireless conection like: # cat /etc/sysconfig/network-scripts/ifcfg-mywireless ESSID="mywireless" MODE=Managed KEY_MGMT=WPA-PSK WPA_ALLOW_WPA2=yes CIPHER_PAIRWISE=CCMP CIPHER_GROUP=CCMP TYPE=Wireless #BOOTPROTO=none #IPADDR=192.168.1.50 #PREFIX=24 #GATEWAY=192.168.1.1 #DNS1=8.8.8.8 #DNS2=8.8.4.4 DEFROUTE=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no NAME="Auto mywireless" UUID=874***** ONBOOT=yes LAST_CONNECT=1355923469 BRIDGE=br0 After, I restart the network: # /etc/init.d/network restart Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface Auto_mywireless: Error: Unknown connection: 874***** [FAILED] Bringing up interface br0: [ OK ] But as you can see, it show a error. My ifconfig output shows now: # ifconfig br0 Link encap:Ethernet HWaddr 6E:20:AD:CE:D8:AB inet addr:192.168.1.50 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6c20:adff:fece:d8ab/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:67 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:6393 (6.2 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:432 errors:0 dropped:0 overruns:0 frame:0 TX packets:432 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:62433 (60.9 KiB) TX bytes:62433 (60.9 KiB) ra0 Link encap:Ethernet HWaddr 00:22:F7:2B:87:E5 inet addr:192.168.1.42 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::222:f7ff:fe2b:87e5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:46 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:487894880 (465.2 MiB) TX bytes:148136473 (141.2 MiB) virbr0 Link encap:Ethernet HWaddr 52:54:00:5B:30:9A inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:70 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:5838 (5.7 KiB) But this doesn't give internet connection and I loss access to 192.168.1.50. So, it is possible setup this networking bridge WiFi-to-Ethernet?

Read the article
Microphones not working on Apple macbook Air 1,1 (Early 2008) under Linux

- by jj_p

I'm running Linux on an mba. I can't make the microphones (neither external nor internal) work. I test using alsamixer and arecord -d 5 test-mic.waw together with aplay test-mic.waw It seems there is a problem with kernel trying to decipher Apple (intentionally) corrupted 'bios', in particular the mic pins are wrongly assigned. As far as we are concerned here, is there any difference between using EFI and BIOS-compatibility mode? (see https://wiki.archlinux.org/index.php/MacBook where they claim to have everything working out of the box on mba1,1) A nice proposal would be to compile the latest Linux kernel and run hda-jack-retask to find the right configuration (in the case of Realtek codec, the missing things I'm supposed to check are either some vendor-specific COEF verbs, EAPD or GPIO setup.), and then come up with a kernel patch to address the issue. Since I'm not that familiar with this last part of the story, can anyone help me through this process? Some useful data: The output from alsa script run as root http://www.alsa-project.org/db/?f=adae8ebee1007043fe83414ac4972319e02255fa The command hda-jack-sense-test -a (with external mic in) Pin 0x14 (Internal Speaker): present = No Pin 0x15 (Green HP Out): present = Yes Pin 0x16 (Not connected): present = No Pin 0x17 (Not connected): present = No Pin 0x18 (Not connected): present = No Pin 0x19 (Not connected): present = No Pin 0x1a (Not connected): present = No Pin 0x1b (Not connected): present = No Pin 0x1c (Not connected): present = No Pin 0x1d (Not connected): present = No Pin 0x1e (Not connected): present = No Pin 0x1f (Not connected): present = No Most likely the chip is Realtek ALC885 (compare also ALC889A) http://guide-images.ifixit.net/igi/bBTSqaeK5JpQ1AWe.large , although at the moment alsa reads it as ALC889A Takashi Iwai's tutorial https://www.kernel.org/doc/Documentation/sound/alsa/HD-Audio.txt Some people researched the original files from a running OS X installation on this same model (I think the relevant files are AppleHDA.kext/Contents/MacOS/AppleHDA AppleHDA.kext/Contents/PlugIns/AppleHDAHardwareConfigDriver.kext/Contents/Info.p????list AppleHDA.kext/Contents/Resources/layout12.xml.zlib AppleHDA.kext/Contents/Resources/Platforms.xml.zlib) http://www.insanelymac.com/forum/topic/220090-alc889a-pin-configuration/#entry1554954 Datasheet http://www.realtek.info/pdf/ALC885_1-1.pdf (from the same Realtek, one can also try to download Linux driver, but this is just taken from ALSA project, as stated in the readme file.) Compare with this Arch guy http://www.alsa-project.org/db/?f=3ca8243c0626844f0264a3faad0aa72018bc14f4 Here for the first time support to audio (except mics) for mba1,2 (which is morally the same as 1,1) is patched into the kernel http://www.alsa-project.org/pipermail/alsa-devel/2010-February/025511.html The same jack supposedly works both for HP and ext MIC, I think it's called TRRS, and it's the same as the one used e.g. for iphones This guy might have done a similar job, though to a more recent version and for sound globally, not just mics: http://blogs.aerys.in/jeanmarc-leroux/2013/09/15/fixing-2013-macbook-air-ubuntu-sound-issue/ (this is mirror to http://unix.stackexchange.com/questions/73044/microphones-not-working-on-apple-macbook-air-1-1-early-2008-under-linux )

Read the article
Impossible to create/format install window 7 on unpartioned HD

- by fra pet

Hi guys i am getting nut reinstalling windows 7 on one of those Acer aspire all-in-one... The original OS(windows professional x64) was not starting, after the initial screen the bios was prompted. So step 1: i tried to access the system partition and reinstall everything but could not get at the point step 2: i set the bios to native ide and i tried to insert my original copy of windows professional and do a clean installation, but it does not allow me to format/create other partion form the installation mask step 3: my BAD, i tried to install ubuntu and i clean the whole hard drive, i was getting an error at some point during installation so i decided to get back to windows step 4: Windows 7 again, at the disk screen of the windows installation i entered into the prompt and played around with DISKPART... -i listed the disk and the HD was disk 0. -i selected disk 0. -i CLEAN disk 0 successfully. -i tried to create a CREATE PARTITION PRIMARY but gave an error cache corrupt and disk not up-to-date (after i try to create a partiton in disk 0 it disappear when i try LIST DISK and i have to restart before he can list DISK 0 again, RESCAN did not worked). -tried CLEAN ALL(2 hours) and succeeded. -try again to create primary partition and failed, same errors -try to install my old copy of windows xP pro and it seems to work, it create a partition, format(only quick worked, slow mode was at 0% after 1 hour so i stop), it start installing and around 90% installation said it could not copy a file and he stop -back on windows 7 again, it says that the hard drive has 490+gb unpartitioned but won't create a partition and format. -i tried again DISKPART as i though i messed up with the MBR when i installed ubuntu, so i did all of the instruction below http://www.sevenforums.com/tutorials/20864-mbr-restore-windows-7-master-boot-record.html http://support.microsoft.com/kb/927392 the errors were: on bootsect: the systne partiton was not found, Data error cyclic redundancy check on bootrec /FixMbr: A device attached to the system is not functioning but did not worked, and still can not partiton/format/install on a blank HD i tried some bootable clean disk tool and start infinite loop on the same errors the bios setting are: sata: native ide. if i put AHCL(or something like that does not load the HD and the DVD). quick start/quite start: disabled. Are there any other option or tools i can try before i try change the HD(That is my last option)? Thanks to everyone.

Read the article
OpenSSH does not accept public key?

- by Bob

I've been trying to solve this for a while, but I'm admittedly quite stumped. I just started up a new server and was setting up OpenSSH to use key-based SSH logins, but I've run into quite a dilemma. All the guides are relatively similar, and I was following them closely (despite having done this once before). I triple checked my work to see if I would notice some obvious screw up - but nothing is apparent. As far as I can tell, I haven't done anything wrong (and I've checked very closely). If it's any help, on my end I'm using Cygwin and the server is running Ubuntu 12.04.1 LTS. Anyways, here is the output (I've removed/censored some parts for privacy (primarily anything with my name, website, or its IP address), but I can assure you that nothing is wrong there): $ ssh user@host -v OpenSSH_5.9p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Connecting to host [ipaddress] port 22. debug1: Connection established. debug1: identity file /home/user/.ssh/id_rsa type 1 debug1: identity file /home/user/.ssh/id_rsa-cert type -1 debug1: identity file /home/user/.ssh/id_dsa type -1 debug1: identity file /home/user/.ssh/id_dsa-cert type -1 debug1: identity file /home/user/.ssh/id_ecdsa type -1 debug1: identity file /home/user/.ssh/id_ecdsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9p1 Debian-5ubuntu1 debug1: match: OpenSSH_5.9p1 Debian-5ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: sending SSH2_MSG_KEX_ECDH_INIT debug1: expecting SSH2_MSG_KEX_ECDH_REPLY debug1: Server host key: ECDSA 24:68:c3:d8:13:f8:61:94:f2:95:34:d1:e2:6d:e7:d7 debug1: Host 'host' is known and matches the ECDSA host key. debug1: Found key in /home/user/.ssh/known_hosts:2 debug1: ssh_ecdsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: /home/user/.ssh/id_rsa debug1: Authentications that can continue: publickey debug1: Trying private key: /home/user/.ssh/id_dsa debug1: Trying private key: /home/user/.ssh/id_ecdsa debug1: No more authentication methods to try. Permission denied (publickey). What can I do to resolve my problem?

Read the article
SSH_ORIGINAL_ENVIRONMENT error with snow leopard client to a gitosis server on debian

- by Mica

I have a server running gitosis (installed from the package manager) on debian lenny. I am able to perform all operations from my linux mint laptop, but from my Mac running an up-to-date Snow Leopard gives me the following error: mica@waste Desktop$ git clone [email protected]:Poems.git Initialized empty Git repository in /Users/micas/Desktop/Poems/.git/ ERROR:gitosis.serve.main:Repository read access denied fatal: The remote end hung up unexpectedly mica@waste Desktop$ ssh -v [email protected] OpenSSH_5.2p1, OpenSSL 0.9.8l 5 Nov 2009 debug1: Reading configuration data /etc/ssh_config debug1: Applying options for * debug1: Connecting to 192.168.0.156 [192.168.0.156] port 22. debug1: Connection established. debug1: identity file /Users/micas/.ssh/identity type -1 debug1: identity file /Users/micas/.ssh/id_rsa type 1 debug1: identity file /Users/micas/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.1p1 Debian-5 debug1: match: OpenSSH_5.1p1 Debian-5 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.2 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host '192.168.0.156' is known and matches the RSA host key. debug1: Found key in /Users/mica/.ssh/known_hosts:5 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password debug1: Next authentication method: publickey debug1: Offering public key: /Users/mica/.ssh/id_rsa debug1: Remote: Forced command: gitosis-serve mica@waste debug1: Remote: Port forwarding disabled. debug1: Remote: X11 forwarding disabled. debug1: Remote: Agent forwarding disabled. debug1: Remote: Pty allocation disabled. debug1: Server accepts key: pkalg ssh-rsa blen 277 debug1: Remote: Forced command: gitosis-serve micas@waste debug1: Remote: Port forwarding disabled. debug1: Remote: X11 forwarding disabled. debug1: Remote: Agent forwarding disabled. debug1: Remote: Pty allocation disabled. debug1: Authentication succeeded (publickey). debug1: channel 0: new [client-session] debug1: Requesting [email protected] debug1: Entering interactive session. debug1: Requesting authentication agent forwarding. PTY allocation request failed on channel 0 ERROR:gitosis.serve.main:Need SSH_ORIGINAL_COMMAND in environment. debug1: client_input_channel_req: channel 0 rtype exit-status reply 0 debug1: client_input_channel_req: channel 0 rtype [email protected] reply 0 debug1: channel 0: free: client-session, nchannels 1 Connection to 192.168.0.156 closed. Transferred: sent 2544, received 2888 bytes, in 0.1 seconds Bytes per second: sent 29642.1, received 33650.3 debug1: Exit status 1 Extensive googling of the error isn't returning much-- I changed the /etc/sshd_config file on my Mac as per http://www.schmidp.com/2009/06/23/enable-ssh-agent-key-forwarding-on-snow-leopard/. I still get the same error.

Read the article
Trouble setting up PATH for Java on Debian

- by milkmansrevenge

I am trying to get Oracle Java 7 update 3 working correctly on Debian 6. I have downloaded and set up the files in /usr/java/jre1.7.0_03. I have also set the following two lines at the end of /etc/bash.bashrc: export JAVA_HOME=/usr/java/jre1.7.0_03 export PATH=$PATH:$JAVA_HOME/bin Logging in as other users and root is fine, Java can be found: chris@mc:~$ java -version java version "1.7.0_03" Java(TM) SE Runtime Environment (build 1.7.0_03-b04) Java HotSpot(TM) 64-Bit Server VM (build 22.1-b02, mixed mode) However there are two cases where Java cannot be found as detailed below. Note that both of these worked fine when I have previously installed OpenJDK Java 6 via aptitude, but I need Oracle Java 7 for various reasons. Most importantly, I cannot run commands as another user via su, despite the PATH showing that Java should be present. The user was created with adduser chris root@mc:~# su chris -c "echo $PATH" /usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/java/jre1.7.0_03/bin:/bin root@mc:~# su chris -c "java -version" bash: java: command not found root@mc:~# su chris -c "/usr/java/jre1.7.0_03/bin/java -version" java version "1.7.0_03" ... How can it be in the PATH but not be found? Update 05/04/2012: explained by Daniel, to do with it being a non-interactive shell so files such as /etc/profile and /etc/bash.bashrc are not executed. Doing a full swap to that user and running Java works: root@mc:~# su chris chris@mc:/root$ java -version java version "1.7.0_03" ... I run a script on start up which exhibits similar but slightly different problems. The script is located in /etc/init.d/start-mystuff.sh and calls a jar: #!/bin/bash # /etc/init.d/start-mystuff.sh java -jar /opt/Mars.jar I can confirm that the script runs on start up and the exit code is 127, which indicates command not found. Inserting a line to print/save the PATH shows that it is: /sbin:/usr/sbin:/bin:/usr/bin This second problem isn't as important because I can just point directly to the Java executable in the script, but I am still curious! I have tried setting the full PATH and JAVA_HOME explicitly in /etc/environment which didn't help. I have also tried setting them in /etc/profile which doesn't seem to help either. I have tried logging in and out again after setting PATH in the various locations (duh!). Anyway, long post for what will probably have a simple one line solution :( Any help with this would be greatly appreciated, I have spent far too long trying to fix it by myself. Motivation The first problem may seem obscure but in my system I have users that are not allowed SSH access yet I still want to run processes as them. I have a ton of scripts operating in this way and don't want to have to change them all.

Read the article
Suggestions for sharing and using data between Ubuntu and Windows 7 dual boot

- by wizjany

Note: TL;DR, scroll to bottom for summary. I recently set up my computer for a dual boot between Ubuntu 9.10 and Windows 7. My current drive setup is as follows. | A1 | A2 | | B1 | B2 | B3 | A1: 100 mb, windows 7 "System Reserved" boot partition A2: 230 gb, data section, this one needs to be shared between the operating systems B1: 125 gb, windows 7 OS B2: 123 gb, ubuntu OS B3: 2gb, linux swap space Pretty much i want to have my documents, music, pictures, videos, etc accessible from both operating systems. My first attempt involved making the data (a2) partition NTFS, and moving my home folder from ubuntu to the data partition. However, as I read NTFS does not work nice with permission, and it messed up my home folder. My next idea is one of the following: 1) format the data partition to ext2/3/4 and move my home folder from linux there, and get a driver to read ext partitions in windows 7. The problem with that is that most of the ext drivers/software are not compatible with windows 7 or do not integrate with windows explorer (I really don't want to open a separate software window just to access my data, plus it's probably not compatible with other software.) http://www.fs-driver.org/ looks promising, but I'm not sure how it works with ext4 and windows 7 (not officially supported, when trying in vista compatibility mode, it tells me I need to format the ext drive to use it). My next idea, 2) keep the home folder in ubuntu where it is, but create symlinks for the Documents, Music, etc folders to an NTFS formatted Data (A2) partition, and add those locations to the windows 7 libraries. I'm not totally sure how the permissions would work out, but it should be fine since it's only the documents, music, etc and not the important config files in the rest of /home/user/. Correct me if I'm wrong. Currently, symlinks is my best idea, although i'm not sure how it will work. Any suggestions, additions to my ideas, links, pointers, whatever would be greatly appreciated. Even if it means i should reformat both my drives and repartition (2 250gb drives if you want to suggest a setup for that), I won't be too opposed if that's the best suggestion (I've gone through the format/install/format/reinstall process 5 times over the past 3 days, once more won't hurt me). TL;DR, summary: I have two hard drives. One is partitioned for Ubuntu and Windows 7, the second one I want accessible to both operating systems to store documents, music, pictures, videos, etc. Suggestions on how to set up the data drive please =) P.S. bonus if I can get an apache server document root folder working between the two OS's as well (permissions could become very complicated, so don't worry too much about that) P.P.S. Related question, but data viewing is one way: http://superuser.com/questions/84586/partition-scheme-and-size-for-dual-boot-windows-7-and-ubuntu-9-10-with-separate-p

Read the article
Critique My Backup and Storage Plan

- by MetaHyperBolic

My current storage (RAID-1 off of a hardware RAID card) and backup (a spare drive) solutions for my home network are inadequate. I have too much data scattered on various one-off drives. It is time to evolve. Backups seem simple enough, at least: lots of big drives. However, I am bewildered by the number of choices for small home storage. The Drobo S looks appealing. So does the ReadyNAS. I am not looking for bunches of shiny features, I'm mostly interested in reliability. I am not interested in building Yet Another PC to create a file server or doing something in the cloud, or whatever. I'm stupid, so I am keeping it simple. Requirements for Main Volume: Starting working space roughly 2TB, with options for growth up to 5TB RAID or something RAID-like with at least one parity drive eSATA II for speed during backups Ability to shut down gracefully when alerted of low power by a UPS Optional but Desirable: Will take 2TB drives now with options for the larger 3TB drives coming in 2010-2011 Optional but Desirable: : RAID-6 or something similar, with two parity drives Optional but Desirable: : Hot spare Ethernet connection not required, as the volume will be shared via the same machines which runs my home print server Backups: Backup performed via ROBOCOPY in mirror mode to an external hard drive via a eSATA II connection. Start with rotating between two external 2TB hard drives, will go up to six external 2TB drives. Start with a weekly backup, move to a bi-weekly backup as more drives are added. Move to 3TB drives as the size of my main volume increases. Backup drives will be stored on an off-site location. Hard drives: I plan on buying all of the same model, but different batches from different vendors. I found a "burn-in" utility with which I can pound away on the drives for a couple of weeks before adding them to the backup pool or the main volume. I estimate that I am looking at roughly $1,500 to start, once I start throwing in two TB drives for backup and four for storage. So, are there any obvious flaws in my plan? What have I overlooked? Any suggestions for the storage device for my main volume that fits my requirements? Or do I just keep it simple, 2 drives in RAID-1, then perform due diligence with my backups, accepting that I will have to buy a whole new unit when my data grows past 2TB?

Read the article
Kickstart based installation of RHEL 6.4 from USB

- by Peter

I want to setup some brand new servers with RHEL 6.4. Servers do not have DVD, so, I have to use USB for the installation. I already have a custom ISO with a kickstart file that I use on servers with DVD flawlessly. I used iso2usb to move the ISO t? my USB. When I boot from the USB, the ks file is found, anaconda starts, but then stops with the following error: "The installation source given by device ['sda1'] could not be found. Please check your parameters and try again" Notes: The USB IS the sda. My custom ISO file is renamed to linux.iso from iso2usb and it is present in the root directory of the USB. Kickstart file has the following entry: harddrive --partition=sda1 --dir=/ Please help me to automate the installation with kickstart. Edit 1: This the anaconda.log file: 09:01:57,029 INFO : no /etc/zfcp.conf; not configuring zfcp 09:01:57,259 INFO : created new libuser.conf at /tmp/libuser.4rAbps with instPath="/mnt/sysimage" 09:01:57,259 INFO : anaconda called with cmdline = ['/usr/bin/anaconda', '--stage2', 'hd:sda1:///images/install.img', '--dlabel', '--kickstart', '/tmp/ks.cfg', '--graphical', '--selinux', '--lang', 'en_US.UTF-8', '--keymap', 'us', '--repo', 'hd:sda1:/'] 09:01:57,260 INFO : Display mode = g 09:01:57,260 INFO : Default encoding = utf-8 09:01:59,444 DEBUG : X server has signalled a successful start. 09:01:59,446 INFO : Starting window manager, pid 1345. 09:01:59,537 INFO : Starting graphical installation. 09:01:59,741 INFO : Detected 7968M of memory 09:01:59,741 INFO : Swap attempt of 7968M 09:02:00,840 INFO : ISCSID is /usr/sbin/iscsid 09:02:00,840 INFO : no initiator set Edit 2: This is the part of anaconda log that indicates that it found the USB etc: 09:01:47,918 INFO : starting STEP_STAGE2 09:01:47,918 INFO : partition is sda1, dir is //images/install.img 09:01:47,918 INFO : mounting device sda1 for hard drive install 09:01:48,005 INFO : Path to stage2 image is /mnt/isodir///images/install.img 09:01:54,214 INFO : mounted loopback device /mnt/runtime on /dev/loop0 as /tmp/install.img 09:01:54,214 INFO : Looking for updates for HD in /mnt/isodir///images/updates.img 09:01:54,214 INFO : Looking for product for HD in /mnt/isodir///images/product.img 09:01:54,227 INFO : got stage2 at url hd:sda1:///images/install.img 09:01:54,254 INFO : Loading SELinux policy 09:01:54,700 INFO : getting ready to spawn shell now 09:01:54,975 INFO : Running anaconda script /usr/bin/anaconda 09:01:56,882 INFO : _Fedora is the highest priority installclass, using it 09:01:56,921 INFO : Running kickstart %%pre script(s) 09:01:56,922 WARNING : '/bin/sh' specified as full path 09:01:56,926 INFO : All kickstart %%pre script(s) have been run

Read the article
Apache + Tomcat error 120006 Using mod_proxy_ajp for Load Balance

- by Wakaru44

I have an apache 2 frontend with two nodes, and a backend with two instances of tomcat 6 balance with mod_proxy_ajp. The bbdd is in a separate machine. All machines use RHEL, 6.2 on the frontend, 5.5 on the backend. The infraestructure is virtualized using VMware. # This is the apache config in one of the virtualHost. ProxyPreserveHost On ProxyPass / balancer://liferay/ <Proxy balancer://liferay> BalancerMember ajp://lrab:8009 route=liferaya BalancerMember ajp://lrbb:8009 route=liferayb status=+H ProxySet lbmethod=byrequests nofailover=on </Proxy> The conector in tomcat is now configured like this:  <Connector port="8009" protocol="AJP/1.3" redirectPort="8443" URIEncoding="UTF-8" enableLookups="false" allowTrace="true" /> Do you think it could be useful to set a maxThreads parameter, like in this post?? in that case, How can i determine a proper number of threads? From time to time, we get errors like this [Tue Sep 18 17:57:02 2012] [error] ajp_read_header: ajp_ilink_receive failed [Tue Sep 18 17:57:02 2012] [error] (120006)APR does not understand this error code: proxy: read response failed from 192.168.1.104:8009 (lrab) And apache switches to the pasive node (if its active) or fails with 503. Some things i have tried so far: I think that i have some performance issues with one of the applications, Here you can see a threadDump But i'm not quite sure about it. I also started to monitor the network connection. I have noticed that there are some pings lost when i have a "ping -f " so maybe it could be a network issue, but the success rate is 100% (so the lost packets are only a few among the flood, but maybe, i don't know, enough to break the link betwen apache and tomcat). I wrote a python script to check connectivity with timestamps on the pings, so i can know when the network fails. After sniffing the network , i can also see some RST packets, but i don't know if that is a normal behaviour (some applications do that to end a network communication). I have also noticed that the applications have problems communicating with the database, but im not even sure if this could be related or not. If you think so, i can post more info about it. I changed the connector on the tomcats to use the native one, but still the same. I need not even a solution to this, but maybe some guidance on how can i troubleshoot this better ¿Analyze threads, monitor mysql performance, sniff the traffic between apaches and tomcats? Ultimately, all i need is to balance the tomcat instances in Active/pasive mode, so if there is another way to do it, i could give it a try.

Read the article
Having troubles connectiong Magento to external Windows Database Server using Windows Azure

- by Kevin H

"I tried to make this easy to read through" I am using Ubuntu 12.04 LTS for Magento and installed these commands onto the system: sudo apt-get install apache2 sudo apt-get install php5 libapache2-mod-php5 sudo apt-get install php5-mysql sudo apt-get install php5-curl php5-mcrypt php5-gd php5-common sudo apt-get install php5-gd I used Windows Server 2008 R2 August 2012 for Mysql Server For a reference, I used http://www.windowsazure.com/en-us/manage/windows/common-tasks/install-mysql/ When the server was setup, I added an empty disk to it Then, I added endpoints 3306 Next I accessed the server remotely After that, I formatted the empty disk and was inserted as F: Next I downloaded Mysql from http://*.mysql.com version Windows (x86, 64-bit), MSI Installer 5.5.28 In the installation process, I used these settings: Typical Setup - Clicked Next, install, next Chose Detailed Configuration - Clicked next Chose Dedicated MySQL Server Machine - Clicked Next Chose Transactional Database Only - Clicked Next Chose the "F:" Drive - Clicked Next Chose Online Transactional Processing (OLTP) - Clicked Next For Networking Options, I checkmarked 'Enable TCP/IP Networking" 'Add firewall exception for this port' 'Enable Strict Mode' - Clicked Next Chose Standard Character Set - Clicked Next For Windows Options, I checkedmarked 'Install as Window Service" 'Launch the MySQL Server automatically' 'Include Bin Directory in Windows PATH - Clicked Next For Security Options, I checkmarked 'Modify Security Settings' and set root password - Clicked Next Finally clicked Execute and Finish These are the Firewall Setting that I set I clicked inbound rules Properties Scope Allow IP Address and used the internal Address for Magento Server Clicked Apply and exited Next, I opened up MySQL 5.x Command Line Client Entered Root Password Then entered these commands mysql create database magento; mysql Create user magentouser identified by 'password'; mysql Grant select, insert, create, alter, update, delete, lock tables on magento.* to magentouser mysql exit Finally, I opened up the Magento Downloader Magento validation has approved all PHP version is right. Your version is 5.3.10-1ubuntu3.4. PHP Extension curl is loaded PHP Extension dom is loaded PHP Extension gd is loaded PHP Extension hash is loaded PHP Extension iconv is loaded PHP Extension mcrypt is loaded PHP Extension pcre is loaded PHP Extension pdo is loaded PHP Extension pdo_mysql is loaded PHP Extension simplexml is loaded These are all installed on Magento Server For the Database Connection, I used: The Database server only has MySQL 5.5 Server installed on it Host - Internal IP address User Name - The User I created when setting up database Password - The Password I created when setting up database For the password, I did some research and found out that Magento only accepts alphanumeric, so I went and set it up again and used only alphanumeric for the User password Now, I am still getting Accessed denied for database Connection. Also, I have tryed to setup mysql on independant Linux Server but kept getting errors. When, I found the solution. Wouldn't work, so I decided to try Windows. These is the questions, I have been asking and researching to debug this issue Is it because I am using Linux for magento and Windows for Database. I have had no luck in finding a reason why this wouldn't work There must be something, I am missing I also researched the difference between linux sql databases and windows sql databases but have not come to conclusion, if installing Mysql on windows would make a difference in syntax and coding. I have spent a lot of time looking into this and need some help with direction on how to complete my project. Any type of help would be appreciated.

Read the article
WinXP - Having trouble sharing internet with 3G USB modem via ICS

- by Carlos Nunez

all! I've been banging my head against a wall with this issue for a few days now and am hoping someone can help out. I recently signed up for T-Mobile's webConnect 3G/4G service to replace the faltering (and slow) DSL connection in my apartment. The goal was to put the SIM in one of my old phones and use its built-in WLAN tethering feature to share Internet out to rest of my computers. I quickly found out that webConnect-provisioned SIMs do not work with regular smartphones, so I was forced to either buy a 4G-compatible router or tether one of my old laptops to my wireless router and share out that way. I chose the latter, and it's sharpening my inner masochistic self by the day. Here's the setup: GSM USB modem (via hub), ICS host - 10/100 Mbps Ethernet NIC, ICS "guest" - WAN port of my SMC WGBR14N wireless router in bridged mode (i.e. wireless access point). Ideally, this would make my laptop the DHCP server and internet gateway with the WAP giving everyone wireless coverage. I can browse internet on the host laptop fine. However, when clients try to connect, they get a DHCP-assigned IP from the laptop and are able to use the Internet for a few minutes before completely dying. After that happens, they are able to re-associate with the WAP and get IP addresses, but are unable to use Internet or resolve IP addresses until the laptop and router are restarted. If they do get access, it's very, very slow. After running Wireshark on the host machine, it turns out that this is because every TCP connection keeps getting RST. DNS seems to work. I would normally think the firewall is the culprit here, but when it drops packets, it drops them completely. The fact that TCP connections are being ACK'ed by the destination rules that out. Of course, none of the event Log isn't saying anything about what's going on. I also tried disabling power management on the NIC, since that's caused problems in the past; that didn't help either. I finally disabled receive-side scaling as per a Microsoft KB (that applied to Windows Server 2003, SP2) to no avail. I'm thinking of trying it with a different NIC (will be tough; don't have a spare Ethernet NIC around for the laptop), but I'm getting the impression that this simply doesn't work. Can anyone please advise? I apologise for the length of this post; all contributions are much appreciated! -Carlos.

Read the article
Changing User/Group to allow PHP to chmod/rename and move_upload_file()

- by moe

Hi There, It seems like I cannot do anything with my PHP script on my VPS. It returns 'Permission denied' when I try to upload something to a directory. Yes, I have changed the permission to 777, and it works, but I do not like the insecurity When running the command: ps axu|grep apache|grep -v grep It returns nobody 7689 0.1 3.8 50604 20036 ? S 21:38 0:00 /usr/local/apache/bin/httpd -k start -DSSL root 13600 0.0 3.8 50304 20348 ? Ss Jun06 0:46 /usr/local/apache/bin/httpd -k start -DSSL nobody 15733 0.1 3.8 50700 20156 ? S 21:39 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 15818 0.1 3.8 51492 20180 ? S 21:39 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 23843 0.1 3.7 51336 19592 ? S 21:40 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 30335 0.0 3.5 50436 18496 ? S 21:41 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 30406 0.0 3.5 50444 18544 ? S 21:41 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 30407 0.0 3.5 50556 18696 ? S 21:41 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 30472 0.0 3.6 50828 19348 ? S 21:41 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 30474 0.0 3.5 50668 18868 ? S 21:41 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 30476 0.0 3.6 50532 19064 ? S 21:41 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 30501 0.0 3.8 50556 20080 ? S 21:36 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 32341 0.0 3.5 50444 18492 ? S 21:41 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 32370 0.0 3.5 50444 18476 ? S 21:42 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 32414 0.1 3.7 51336 19524 ? S 21:42 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 32416 0.1 3.5 50668 18816 ? S 21:42 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 32457 0.1 3.6 50828 19320 ? S 21:42 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 32458 0.1 3.6 50772 19276 ? S 21:42 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 32459 0.0 3.5 50444 18504 ? S 21:42 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 32460 0.2 3.6 50828 19320 ? S 21:42 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 32463 0.0 3.5 50444 18472 ? S 21:42 0:00 /usr/local/apache/bin/httpd -k start -DSSL nobody 32466 0.0 3.4 50436 17960 ? S 21:42 0:00 /usr/local/apache/bin/httpd -k start -DSSL The owner of the directory is 'user [505]' and the group is 'user[508]' (as seen in WinSCP) What can I do to change the Apache Handler to the right owner and group to allow my PHP scripts to work? P.S My PHP is not set to safe mode, and the open_basedir is set to no value

Read the article
What the hell was THAT?!?

- by Massimo

My system is Windows XP SP3, updated with the latest patches. The PC is connected to a Cisco 877 ADSL router, which does NAT from the internal network to its single static public IP address. There are no forwarded ports, and the router's management console can only be accessed from the inside. I was doing two things: working on a remote office machine via VPN and browsing some web pages on the Cisco web site. The remote network is absolutely safe (it's a lab network, four virtual servers, no publicly accessible services and no users at all; also, none of what I'm going to describe ever happened there). The Cisco web site... well, I suppose is quite safe, too. Suddenly, something happened. Strange popups appears anywhere; programs claiming they're "antimalware", "antispyware" et so on begins autoinstalling; fake Windows Update and Security Center icons pop up in the system tray. svchost.exe began crashing repeatedly. Then, finally, after some minutes of this... BSOD. And, upon rebooting, BSOD again. Even in safe mode. Ok, that was obviously some virus/trojan/whatever. I had to install a new copy of Windows on another partition to clean things up. I found strange executables, services and DLLs almost anywhere. Amongst the other things, user32.dll and ndis.sys had been replaced. A fake software called "Antimalware Doctor" had been installed. There were services with completely random names or even GUIDs (!), and also ones called "IpSect" and "Darkness". There were executable files without an .exe extension. There were even two boot-class drivers, which I'm quite sure are the ones that finally caused the system to crash. A true massacre. Ok, now the questions: What the hell was that?!? It was something more than a simple virus! How did it manage to attack my computer, as I am behind a firewall and was not doing anything even only potentially harmful on the web at the time?

Read the article
Proxy / Squid 2.7 / Debian Wheezy 6.7 / lots of TCP Timed-out

- by Maroon Ibrahim

i'm facing a lot of TCP timed-out on a busy cache server and here below my sysctl.conf configuration as well as an output of "netstat -st" Kernel 3.2.0-4-amd64 #1 SMP Debian 3.2.57-3 x86_64 GNU/Linux Any advice or help would be highly appreciated #################### Sysctl.conf cat /etc/sysctl.conf net.ipv4.tcp_tw_reuse = 1 net.ipv4.tcp_tw_recycle = 1 fs.file-max = 65536 net.ipv4.tcp_low_latency = 1 net.core.wmem_max = 8388608 net.core.rmem_max = 8388608 net.ipv4.ip_local_port_range = 1024 65000 fs.aio-max-nr = 131072 net.ipv4.tcp_fin_timeout = 10 net.ipv4.tcp_keepalive_time = 60 net.ipv4.tcp_keepalive_intvl = 10 net.ipv4.tcp_keepalive_probes = 3 kernel.threads-max = 131072 kernel.msgmax = 32768 kernel.msgmni = 64 kernel.msgmnb = 65536 kernel.shmmax = 68719476736 kernel.shmall = 4294967296 net.ipv4.ip_forward = 1 net.ipv4.tcp_timestamps = 0 net.ipv4.conf.all.accept_redirects = 0 net.ipv4.tcp_window_scaling = 1 net.ipv4.tcp_sack = 0 net.ipv4.tcp_syncookies = 1 net.ipv4.ip_dynaddr = 1 vm.swappiness = 0 vm.drop_caches = 3 net.ipv4.tcp_moderate_rcvbuf = 1 net.ipv4.tcp_no_metrics_save = 1 net.ipv4.tcp_ecn = 0 net.ipv4.tcp_max_orphans = 131072 net.ipv4.tcp_orphan_retries = 1 net.ipv4.conf.default.rp_filter = 0 net.ipv4.conf.default.accept_source_route = 0 net.ipv4.tcp_max_syn_backlog = 32768 net.core.netdev_max_backlog = 131072 net.ipv4.tcp_mem = 6085248 16227328 67108864 net.ipv4.tcp_wmem = 4096 131072 33554432 net.ipv4.tcp_rmem = 4096 174760 33554432 net.core.rmem_default = 33554432 net.core.rmem_max = 33554432 net.core.wmem_default = 33554432 net.core.wmem_max = 33554432 net.core.somaxconn = 10000 # ################ Netstat results /# netstat -st IcmpMsg: InType0: 2 InType3: 233754 InType8: 56251 InType11: 23192 OutType0: 56251 OutType3: 437 OutType8: 4 Tcp: 20680741 active connections openings 63642431 passive connection openings 1126690 failed connection attempts 2093143 connection resets received 13059 connections established 2649651696 segments received 2195445642 segments send out 183401499 segments retransmited 38299 bad segments received. 14648899 resets sent UdpLite: TcpExt: 507 SYN cookies sent 178 SYN cookies received 1376771 invalid SYN cookies received 1014577 resets received for embryonic SYN_RECV sockets 4530970 packets pruned from receive queue because of socket buffer overrun 7233 packets pruned from receive queue 688 packets dropped from out-of-order queue because of socket buffer overrun 12445 ICMP packets dropped because they were out-of-window 446 ICMP packets dropped because socket was locked 33812202 TCP sockets finished time wait in fast timer 622 TCP sockets finished time wait in slow timer 573656 packets rejects in established connections because of timestamp 133357718 delayed acks sent 23593 delayed acks further delayed because of locked socket Quick ack mode was activated 21288857 times 839 times the listen queue of a socket overflowed 839 SYNs to LISTEN sockets dropped 41 packets directly queued to recvmsg prequeue. 79166 bytes directly in process context from backlog 24 bytes directly received in process context from prequeue 2713742130 packet headers predicted 84 packets header predicted and directly queued to user 1925423249 acknowledgments not containing data payload received 877898013 predicted acknowledgments 16449673 times recovered from packet loss due to fast retransmit 17687820 times recovered from packet loss by selective acknowledgements 5047 bad SACK blocks received Detected reordering 11 times using FACK Detected reordering 1778091 times using SACK Detected reordering 97955 times using reno fast retransmit Detected reordering 280414 times using time stamp 839369 congestion windows fully recovered without slow start 4173098 congestion windows partially recovered using Hoe heuristic 305254 congestion windows recovered without slow start by DSACK 933682 congestion windows recovered without slow start after partial ack 77828 TCP data loss events TCPLostRetransmit: 5066 2618430 timeouts after reno fast retransmit 2927294 timeouts after SACK recovery 3059394 timeouts in loss state 75953830 fast retransmits 11929429 forward retransmits 51963833 retransmits in slow start 19418337 other TCP timeouts 2330398 classic Reno fast retransmits failed 2177787 SACK retransmits failed 742371590 packets collapsed in receive queue due to low socket buffer 13595689 DSACKs sent for old packets 50523 DSACKs sent for out of order packets 4658236 DSACKs received 175441 DSACKs for out of order packets received 880664 connections reset due to unexpected data 346356 connections reset due to early user close 2364841 connections aborted due to timeout TCPSACKDiscard: 1590 TCPDSACKIgnoredOld: 241849 TCPDSACKIgnoredNoUndo: 1636687 TCPSpuriousRTOs: 766073 TCPSackShifted: 74562088 TCPSackMerged: 169015212 TCPSackShiftFallback: 78391303 TCPBacklogDrop: 29 TCPReqQFullDoCookies: 507 TCPChallengeACK: 424921 TCPSYNChallenge: 170388 IpExt: InBcastPkts: 351510 InOctets: -609466797 OutOctets: -1057794685 InBcastOctets: 75631402 #

Read the article
How can I play my MP3 files through my stereo system?

- by Joel Coehoorn

Here's the situation. Like many others I have my entire CD collection ripped to my PC, along side other music I've acquired through iTunes or Amazon MP3. Also like many others the speakers at my PC are underpowered, and likely included in my monitor as an afterthought. This is fine for most use: system sounds, YouTube, etc. Even games sounds and music. But I'd like something a little better for when I really want to listen to music. And I have it; in the next room — barely 25 feet away as the crow flies — sits a nice 400 watts stereo system. The stereo supports MP3 CDs, so up to this point I've just kept a few CD-RW disks around to keep most of my collection available. But it's time to move on to something a little more sophisticated. What are my options for using the MP3 files available on my computer as an input for this stereo? Some notes: I want to be able to control what song the stereo is playing without having to go to the PC, including setting up and retrieving playlists. Ideally this should even be able to wake the PC from sleep mode to start playing. I primarily use Windows Media Player on the PC (which runs Windows Vista). However, the files themselves live on a server running Windows Server 2008, and so I could also install something on the server and run everything from there. The axillary input on the stereo is unfortunately limited to a 1/8 inch stereo mini-plug. I'm loath to run wires across two rooms, and I'm considering moving the stereo to the garage at some point. Therefore a wireless solution that can easily cover about 100 ft or so is preferred. I already have a Wi-Fi network ready, but it's secured so anything using Wi-Fi should make it easy to set up security. Bonus points for doing it in under $85 shipped at Amazon (I'm hoping to pay for this via $85 worth of Amazon gift cards). I know this a pretty tight budget, so just getting close is okay. Bonus points for something that remembers multiple profiles (keep my favorite songs separate from the wife's). Bonus points for a remote that can also replace my stereo remote, so I only need one device to control everything. I'm not holding my breath on this one given my price range, though. Bonus points if I can also use for Internet radio. Doing some research on my own as well. This looks like it'll do exactly what I want, but it lists at an outrageous $299: http://www.linksysbycisco.com/US/en/products/DMP100

Read the article
possible UDP attack on BIND?

- by Waleed Hamra

hello everyone, i was surprised last month when my EC2 instance (ubuntu precise server), that is supposed to be under the free tier still, accumulated lots of traffic... today, while checking my current billing statement, i noticed i already have tons of traffic, while still in the middle of the month, and i'm fearing what my bill by the end of the month is going to be... i installed bandwidthd, and after few minutes, i noticed lots of UDP traffic to "108.162.233.15". this is apparently a cloudflare IP, and i don't have anything using cloudflare (as far as i know). so i ran "iftop" to see what ports are being used, and i saw the UDP traffic coming from port 80 to my port 53... why would a webserver query dns? so i stopped bind on my server, and ran it in foreground debugging mode, and saw the following query, being repeated continuously: 17-Nov-2012 12:30:58.216 client 108.162.233.15#80: UDP request 17-Nov-2012 12:30:58.216 client 108.162.233.15#80: request is not signed 17-Nov-2012 12:30:58.216 client 108.162.233.15#80: recursion available 17-Nov-2012 12:30:58.216 client 108.162.233.15#80: query 17-Nov-2012 12:30:58.216 client 108.162.233.15#80: query (cache) 'isc.org/ANY/IN' approved 17-Nov-2012 12:30:58.216 client 108.162.233.15#80: send 17-Nov-2012 12:30:58.216 client 108.162.233.15#80: sendto 17-Nov-2012 12:30:58.216 client 108.162.233.15#80: senddone 17-Nov-2012 12:30:58.217 client 108.162.233.15#80: next 17-Nov-2012 12:30:58.217 client 108.162.233.15#80: endrequest 17-Nov-2012 12:30:58.217 client @0x7fbee05126e0: udprecv 17-Nov-2012 12:30:58.343 client 108.162.233.15#80: UDP request 17-Nov-2012 12:30:58.343 client 108.162.233.15#80: request is not signed 17-Nov-2012 12:30:58.343 client 108.162.233.15#80: recursion available 17-Nov-2012 12:30:58.343 client 108.162.233.15#80: query 17-Nov-2012 12:30:58.343 client 108.162.233.15#80: query (cache) 'isc.org/ANY/IN' approved 17-Nov-2012 12:30:58.343 client 108.162.233.15#80: send 17-Nov-2012 12:30:58.344 client 108.162.233.15#80: sendto 17-Nov-2012 12:30:58.344 client 108.162.233.15#80: senddone 17-Nov-2012 12:30:58.344 client 108.162.233.15#80: next 17-Nov-2012 12:30:58.344 client 108.162.233.15#80: endrequest my question is... is this normal? should i be worried? or is this completely irrelevant to my data charges, and i should wait to see more data from bandwidthd? thank you in advance.

Read the article

Search Results

Search found 11207 results on 449 pages for 'kiosk mode'.

Page 396/449 | < Previous Page | 392 393 394 395 396 397 398 399 400 401 402 403 | Next Page >

- by Nathan Adams

- by Alex J. Roberts

- by neverland

- by haridsv

- by Mike Purcell

- by Henadzy

- by Henadzy

- by troutwine

- by shakaran

- by jj_p

- by fra pet

- by Bob

- by Mica

- by milkmansrevenge

- by wizjany

- by MetaHyperBolic

- by Peter

- by Wakaru44

- by Kevin H

- by Carlos Nunez

- by moe

- by Massimo

- by Maroon Ibrahim

- by Joel Coehoorn

- by Waleed Hamra

< Previous Page | 392 393 394 395 396 397 398 399 400 401 402 403 | Next Page >