Search Results

Search found 11207 results on 449 pages for 'kiosk mode'.

Page 397/449 | < Previous Page | 393 394 395 396 397 398 399 400 401 402 403 404  | Next Page >

• Optimal setup for ASUS P6X58D Premium BIOS (no OC)?

  - by rumtscho

  Normally, I'd trust the mainboard manufacturer to choose the best options as defaults. But I had trouble with the board, because even with Quick Boot enabled, it booted twice as slowly as a Pentium 4 Celeron. Then I changed lots of options at once (most of them weren't explained in the manual, just mentioned with a single sentence) and the boot time is only marginally worse than the Pentium 4 (54 sec against 46 sec from button to pw entering screen). Now I don't know if I have turned something off which should have stayed on. I guess I even won't be able to boot from a CD now, because even though it is present in the boot sequence, I took off a timeout I think it needs to check whether there is a disk in the drive. The second reason is that I don't have an internal HDD, only a SSD. I forgot my sources blush but I am under the impression that today's BIOS and OS options are geared toward booting from a HDD, which is often less than optimal when one boots from a SSD, especially when there are functions which cause avoidable writing cycles, as a SSD wears out after too many writing cycles. Most of the things I've read concern the OS, but there are some BIOS-relevant options too. I am especially confused about the disk mode. The board supports AHCI, IDE-simulation and RAID, but of the different articles I've read, there is a proponent for each and no clear arguments for any. So can one tell me which options are important in general and which are important for a SSD-only system? I don't want to overclock the CPU, so you don't have to say anything about this (yes I know the board is meant for OC:)). I am thinking of overclocking the RAM, since they sold me 1600er heatsinked modules which are running at 1066 now, but I'm not sure yet about that. The rest of the system: i7-930, Intel X25-m G2, 6 GB RAM, GTS 250, some no-name Blue-ray ROM. 2 external HDDs over USB 2.0. Lots of other USB-connected hardware (12 devices I think), no SATA 3 drives (will disabling the controller have an impact on performance?), no LAN, only WiFi. Lucid Lynx 64 bit, no dual boot, no virtual installations. The main uses of the system are: managing and playing/showing all the media stored on the external disks, lots of image manipulation, some video editing, a bit of (non-demanding) gaming, rarely development. Lots of Internet surfing too, but this shouldn't have much impact on performance.

  Read the article

• Passwordless ssh failed when login using username

  - by Aczire

  I was trying to setup Hadoop and was stumbled on passwordless ssh to localhost. I am getting a password prompt when trying to connect using ssh username@hostname format. But there is no problem connecting to the machine like ssh localhost or ssh hostname.com. Tried ssh-copy-id user@hostname but it did not work. Using CentOS 6.3 as normal user, I neither have root access or am a sudoer so editing any files like sshd_config is not possible (not even cat the sshd_config file contents). I hope the user login is possible since I can do login without password to localhost, right? Please advise, Here is the ssh debug output. [[email protected] ~]$ ssh -v [email protected] OpenSSH_5.3p1, OpenSSL 1.0.0-fips 29 Mar 2010 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to hostname.com [::1] port 22. debug1: Connection established. debug1: identity file /home/user/.ssh/identity type -1 debug1: identity file /home/user/.ssh/id_rsa type -1 debug1: identity file /home/user/.ssh/id_dsa type 2 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3 debug1: match: OpenSSH_5.3 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.3 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'hostname.com' is known and matches the RSA host key. debug1: Found key in /home/user/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,password debug1: Next authentication method: gssapi-keyex debug1: No valid Key exchange context debug1: Next authentication method: gssapi-with-mic debug1: Unspecified GSS failure. Minor code may provide more information Credentials cache file '/tmp/krb5cc_500' not found debug1: Unspecified GSS failure. Minor code may provide more information Credentials cache file '/tmp/krb5cc_500' not found debug1: Unspecified GSS failure. Minor code may provide more information debug1: Unspecified GSS failure. Minor code may provide more information debug1: Next authentication method: publickey debug1: Offering public key: /home/user/.ssh/id_dsa debug1: Server accepts key: pkalg ssh-dss blen 434 Agent admitted failure to sign using the key. debug1: Trying private key: /home/user/.ssh/identity debug1: Trying private key: /home/user/.ssh/id_rsa debug1: Next authentication method: password [email protected]'s password:

  Read the article

• HAProxy causing delay

  - by user1221444

  I am trying to configure HAProxy to do load balancing for a custom webserver I created. Right now I am noticing an increasing delay with HAProxy as the size of the return message increases. For example, I ran four different tests, here are the results: Response 15kb through HAProxy: Avg. response time: .34 secs Transacation rate: 763 trans/sec Throughput: 11.08 MB/sec Response 2kb through HAProxy: Avg. response time: .08 secs Transaction rate: 1171 trans / sec Throughput: 2.51 MB/sec Response 15kb directly to server: Avg. response time: .11 sec Transaction rate: 1046 trans/sec throughput: 15.20 MB/sec Response 2kb directly to server: Avg. Response time: .05 secs Transaction rate: 1158 trans/sec Throughput: 2.48 MB/sec All transactions are HTTP requests. As you can see, there seems to be a much bigger difference between response times for when the response is bigger, than when it is smaller. I understand there will be a slight delay when using HAProxy. Not sure if it matters, but the test itself was run using siege. And during the test there was only one server behind the HAProxy(the same that was used in the direct to server tests). Here is my haproxy.config file: global log 127.0.0.1 local0 log 127.0.0.1 local1 notice maxconn 10000 user haproxy group haproxy daemon #debug defaults log global mode http option httplog option dontlognull retries 3 option redispatch option httpclose maxconn 10000 contimeout 10000 clitimeout 50000 srvtimeout 50000 balance roundrobin stats enable stats uri /stats listen lb1 10.1.10.26:80 maxconn 10000 server app1 10.1.10.200:8080 maxconn 5000 I couldn't find much in terms of options in this file that would help my problem. I have heard suggestions that I may have to adjust a few of my sysctl settings. I could not find a lot of information on this however, most documentation is for Linux 2.4 and 2.6 on the sysctl stuff, I am running 3.2(Ubuntu server 12.04), which seems to auto tuning, so I have no clue what I should or shouldn't be changing. Most settings changes I tried had no effect or a negative effect on performance. Just a notice, this is a very preliminary test, and my hope is that at deployment time, my HAProxy will be able to balance 10k-20k requests/sec to many servers, so if anyone could provide information to help me reach that goal, it would be much appreciated. Thank you very much for any information you can provide. And if you need anymore information from me please let me know, I will get you anything I can.

  Read the article

• Configuring gmail for use on mailing lists

  - by reemrevnivek

  This is really two questions in one. First, are nettiquette guidelines still accurate in their restrictions on ASCII vs. HTML, posting style, and line length? (Here's a recent metafilter discussion of the topic.) Second, If they are not, should these guidelines be respected? If they are (or if they should still be respected), how can modern mail programs be configured to work properly with them? Most mailing list etiquette statements appear to have been written by sysadmins who loved their command lines, and refuse to change anything. Many still reference rfc1855, written in 1995. Just reading that paginated TXT should give you an idea of the climate at the time. Here's a short, fairly random list of mailing list etiquette statements with some extracted formatting guidelines: Mozilla - HTML discouraged, interleaved posting. FreeBSD - No HTML, don't top post, line length at 75 characters. Fedora - No HTML, bottom-post. You get the idea. You've all seen etiquette statements before. So, assuming that the rules should be obeyed (Usually a good idea), what can be done to allow me to still use a modern mail program, and exchange mail with friends who use the same programs? We like to format our mail. Bold headings, code snippets (sometimes syntax highlighted, if the copy-paste pulls RTF text as from XCOde and Eclipse), free line breaks determined by your browser width, and the (very) occasional image make the message easier to read. Threaded conversations are a wonderful thing. Broadband connections are, I'm sure, the rule for most of the users of SU and of developer mailing lists, disk space is cheap, and so the overhead of HTML is laughable. However, I don't want to post a question to a mailing list and have the guru who can answer my question automatically delete it, or come off as uncaring. Until I hear otherwise, I'll continue to respect the rules as best I can. For a common example of the problem, Gmail, by default, sends HTML formatted messages with bottom-posted quotes (which are folded in, just read the last message immediately above), and uses the frame width to wrap lines, rather than a character count. ASCII can be selected, and quotes can be moved and reversed, but line wraps of quotes don't work, line breaks are tedious to add (and more tedious to read, if they're super small in comparison to the width of the frame). Is there a forwarding, free mail program which can help with this exercise? Should an "RFC1855 mode" lab be written? Or do I have to go to the command line for my mailing lists, and gmail for my other mail?

  Read the article

• Authenticate to VM using vagrant up

  - by utrecht

  Authentication failure during Vagrant Up, while vagrant ssh and ssh vagrant@localhost -p2222 works I would like to execute a shell script using Vagrant at boot. Vagrant is unable to Authenticate, while the VM has been started using vagrant up: c:\temp\helloworld>vagrant up Bringing machine 'default' up with 'virtualbox' provider... ==> default: Importing base box 'helloworld'... ==> default: Matching MAC address for NAT networking... ==> default: Setting the name of the VM: helloworld_default_1398419922203_60603 ==> default: Clearing any previously set network interfaces... ==> default: Preparing network interfaces based on configuration... default: Adapter 1: nat ==> default: Forwarding ports... default: 22 => 2222 (adapter 1) ==> default: Booting VM... ==> default: Waiting for machine to boot. This may take a few minutes... default: SSH address: 127.0.0.1:2222 default: SSH username: vagrant default: SSH auth method: private key default: Error: Connection timeout. Retrying... default: Error: Authentication failure. Retrying... default: Error: Authentication failure. Retrying... default: Error: Authentication failure. Retrying... default: Error: Authentication failure. Retrying... ... After executing CTRL + C it is possible to authenticate to the VM using vagrant ssh and ssh vagrant@localhost -p2222 Vagrant file I use the default Vagrantfile and I only changed the hostname: # -*- mode: ruby -*- # vi: set ft=ruby : # Vagrantfile API/syntax version. Don't touch unless you know what you're doing! VAGRANTFILE_API_VERSION = "2" Vagrant.configure(VAGRANTFILE_API_VERSION) do |config| # All Vagrant configuration is done here. The most common configuration # options are documented and commented below. For a complete reference, # please see the online documentation at vagrantup.com. # Every Vagrant virtual environment requires a box to build off of. config.vm.box = "helloworld" ... Vagrant version c:\temp\helloworld>vagrant --version Vagrant 1.5.1 Question How to authenticate to VM using vagrant up?

  Read the article

• xen-create-image does not create inird or initramfs image and domU does not starts with system image

  - by user219372

  I have Fedora 19 as Dom0. To create image I run # xen-create-image --hostname=debian-wheezy --memory=512Mb --dhcp --size=20Gb --swap=512Mb --dir=/xen --arch=amd64 --dist=wheezy After generation finished I start vm and see: # xl create /etc/xen/debian-wheezy.cfg Parsing config from /etc/xen/debian-wheezy.cfg libxl: error: libxl_dom.c:409:libxl__build_pv: xc_dom_ramdisk_file failed: No such file or directory libxl: error: libxl_create.c:919:domcreate_rebuild_done: cannot (re-)build domain: -3 In the /etc/xen/debian-wheezy.cfg i have # # Kernel + memory size # kernel = '/boot/vmlinuz-3.11.2-201.fc19.x86_64' ramdisk = '/boot/initrd.img-3.11.2-201.fc19.x86_64' and ls -1 /boot/*201* shows /boot/config-3.11.2-201.fc19.x86_64 /boot/initramfs-3.11.2-201.fc19.x86_64.img /boot/System.map-3.11.2-201.fc19.x86_64 /boot/vmlinuz-3.11.2-201.fc19.x86_64 Then if I fix ramdisk directive in .cfg file to /boot/initramfs-3.11.2-201.fc19.x86_64.img vm will start but os inside will not boot. In a tail of xl console I get [ OK ] Reached target Basic System. dracut-initqueue[130]: Warning: Could not boot. dracut-initqueue[130]: Warning: /dev/disk/by-uuid/085883ad-73ca-45cc-8bc5-e6249f869b26 does not exist dracut-initqueue[130]: Warning: /dev/fedora/root does not exist dracut-initqueue[130]: Warning: /dev/fedora/swap does not exist dracut-initqueue[130]: Warning: /dev/mapper/fedora-root does not exist dracut-initqueue[130]: Warning: /dev/mapper/fedora-swap does not exist dracut-initqueue[130]: Warning: /dev/xvda2 does not exist Starting Dracut Emergency Shell... Warning: /dev/disk/by-uuid/085883ad-73ca-45cc-8bc5-e6249f869b26 does not exist Warning: /dev/fedora/root does not exist Warning: /dev/fedora/swap does not exist Warning: /dev/mapper/fedora-root does not exist Warning: /dev/mapper/fedora-swap does not exist Warning: /dev/xvda2 does not exist Generating "/run/initramfs/sosreport.txt" Entering emergency mode. Exit the shell to continue. Type "journalctl" to view system logs. You might want to save "/run/initramfs/sosreport.txt" to a USB stick or /boot after mounting them and attach it to a bug report. dracut:/# .img files in /xen/domains/debian-wheezy exists and listed in disk section of debian-wheezy.cfg So what should i do? Update: I've found that xl does not mount images. In debian-wheezy.cfg I have that: root = '/dev/xvda2 ro' disk = [ 'file:/xen/domains/debian-wheezy/disk.img,xvda2,w', 'file:/xen/domains/debian-wheeze/swap.img,xvda1,w', ] And there is no /dev/xvda* or /dev/sda* or /dev/hda* files in VM.

  Read the article

• Disable Acer eRecovery system

  - by Joel Coehoorn

  The meat of this question is that I'm looking for a way to either require a password before using a recovery partition or "break" the recovery partition (specifically, Acer eRecovery) in a way that I can later "unbreak" only by booting normally into windows first. Here's the full details: I have a set of new Acer Veriton n260g machines in a computer lab. A lot work went into setting up this lab to work well - for example, Office 2007 and other programs needed by the students were installed, all windows updates are applied, and a default desktop is setup. All in all it's several hours work to fully set up one machine. Unfortunately, I don't currently have the ability to easily image these machines, and even if I did I would want to avoid downtime even while an image is restored. Therefore, I've taken steps to lock them down — namely DeepFreeze and a bios password to prevent booting from anywhere but the frozen hard drive. DeepFreeze is an amazing product — as long as you boot from the frozen hard drive, there is no way to actually make permanent changes to that hard drive. Anything you do is wiped after the machine restarts. It lets me give students the leeway to do what they want on lab computers without worrying about them breaking something. The problem is that even with the bios locked and set to only boot from the hard drive, these Acers still have a simple way to choose a different boot source: shut them down and put a paper click in a little hole at the top while you turn it on again. This puts them into the "Acer eRecovery" mode. This by itself is no big deal — you can still power cycle with no impact. But if you then click through the menu to reset the machine (we're now past the point of curiosity and on to intent) it will wipe the hard drive and restore it to the original state. Of course, a few students have already figured this out and reset a couple machines. That's unfortunate, but inevitable. I don't want to destroy the ability to do this entirely (which I could by repartitioning the drives to remove the recovery partition) but I would like a way to require a password first, or "break" the recovery system in a way that I can "unbreak" only if I first un-freeze the hard drive in DeepFreeze. Any ideas?

  Read the article

• Fast user switching suddenly stopped working on my Windows XP Prof machine

  - by John

  When I start Win XP SP2 I get to the welcome screen with no user names displayed. I then press Alt+Ctrl+Del twice and type in the username and then am able to login to Windows. When I go to user accounts in Control Panel I get the error message cells.item(...) is null or not an object. When I go to computer administration and then local users and groups there are no users listed under users but the groups is listed. I did a windows repair with no luck. I tried doing restore points but it said they didn’t work. Please help? My wife and I have been using fast user switching on out computer for years with no problem. Beginning a few months ago, I started Win XP Prof one day I get to the welcome screen with no user names displayed. I then press Alt+Ctrl+Del twice and type in the username and then am able to login to Windows with an account of owner. When I go to user accounts in Control Panel I get the error message cells.item(...) is null or not an object. When I go to computer administration and then local users and groups there are no users listed under users but the groups are listed. I have done system point restores and imports of exports of the registry I take with import. I have tried everything under safe mode and it makes no difference. This followed a Microsoft update the night before as I left the computer on. I tried to do a restore point but all my restore points failed and could not backout the MS updates. I was working with a fellow from Microsoft and he had me do all kinds of things but to no avail. He seems to think a DLL file is corrupt but which one? Finally in desperation he sent me a new OS XP Prof SP3 disk and I installed it and it wiped my hard drive. Luckily I took an Acronis Image backup first so I easily restored my system. I do not want to do a fresh windows update as it is heavily customized and worked fine up to that point. This has been going on for months, Thanks John

  Read the article

• Fedora 13 post security update boot problem

  - by Alex

  Hello. About a month ago I installed a security update that had new Kernek 2.6.34.x from 2.6.33.x), this is when the problem occurred for the first time. After the install my computer would not boot at all, black screen without any visible hard drive activity (I gave it good 30 minutes on black screen, before took actions)... I poped in installation DVD and went in rescue mode to change back the boot option to old kernel (was just a guess where the problem was). After restart computer loaded just file, took a long time for it to start because of SELinux targeted policy relabel is required. Relabeling could take very long time depending on file size. I assumed that the update got messed up somehow and continued working with modified boot option. Couple of days ago, there was another kernel update. I installed it and same problem as before. This rules out corrupted update theory... Black screen right after 'BIOS' screen before OS gets loaded. I had to rescue system again... Below is copy of my grub.conf file. I am fairly new to LINUX (couple of years of experience), mostly development and basic config... nothing crazy. # grub.conf generated by anaconda # # Note that you do not have to rerun grub after making changes to this file # NOTICE: You have a /boot partition. This means that # all kernel and initrd paths are relative to /boot/, eg. # root (hd0,0) # kernel /vmlinuz-version ro root=/dev/mapper/vg_obalyuk-lv_root # initrd /initrd-[generic-]version.img #boot=/dev/sda default=2 timeout=0 splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu title Fedora (2.6.34.6-54.fc13.i686.PAE) root (hd0,0) kernel /vmlinuz-2.6.34.6-54.fc13.i686.PAE ro root=/dev/mapper/vg_obalyuk-lv_root rd_LVM_LV=vg_obalyuk/lv_root rd_LVM_LV=vg_obalyuk/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet initrd /initramfs-2.6.34.6-54.fc13.i686.PAE.img title Fedora (2.6.34.6-47.fc13.i686.PAE) root (hd0,0) kernel /vmlinuz-2.6.34.6-47.fc13.i686.PAE ro root=/dev/mapper/vg_obalyuk-lv_root rd_LVM_LV=vg_obalyuk/lv_root rd_LVM_LV=vg_obalyuk/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet initrd /initramfs-2.6.34.6-47.fc13.i686.PAE.img title Fedora (2.6.33.8-149.fc13.i686.PAE) root (hd0,0) kernel /vmlinuz-2.6.33.8-149.fc13.i686.PAE ro root=/dev/mapper/vg_obalyuk-lv_root rd_LVM_LV=vg_obalyuk/lv_root rd_LVM_LV=vg_obalyuk/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet initrd /initramfs-2.6.33.8-149.fc13.i686.PAE.img I like my system to be up to date... Let me know if I can post any other files that can be of help. Has anyone else had this problem? Does anyone has any ideas how to fix this problem? p.s. Anything helps, you ppl are great! thx for ur time.

  Read the article

• Small Business Server services will not start, and remote desktop and UAC are broken

  - by Stephen Jennings

  Yesterday I began setting up a server with Windows Small Business Server 2008. All I am configuring it for right now is to be a domain controller and Exchange server. I completed the initial setup of SBS then started looking through different connection options (allowing VPN versus using a TS Gateway). After I rebooted one time, I started having three not-obviously-related issues: First, I could no longer remote desktop into the computer. I ran TCPView and saw that it was no longer listening on port 3389. I checked everything in Terminal Service Configuration but everything shows the computer ought to be allowing connections. Also, when I tried to use anything that required user account control elevation, the UAC dialog never popped up and the program that was waiting just froze. If I try to run "regedit" from the Run box, for example, it never appears. When I run in safe mode which does not run with UAC, I was able to access everything. I didn't want to deal with it, so I turned off UAC and rebooted. Finally, in the Windows SBS Console, there are status indicators for Security, Updates, Backup, and Other Alerts. The first three get stuck saying "Querying". Looking in the computer alerts, I have events showing the following services stopped: Background Intelligent Transfer Service KtmRm for Distributed Transaction Coordinator Distributed Transaction Coordinator Microsoft Exchange Information Store Microsoft Exchange System Attendant Microsoft Exchange Transport Windows Remote Management Update Services Windows Update I figured I must have configured something wrong accidentally and I couldn't find anything using Google explaining what might be the case, so I just decided to format the hard drive and reinstall SBS from scratch. I did this and everything was working last night, but I just turned the machine back on and it is doing the same thing again! On my second install, I did not configure anything except the following (all from SBS Console): Connect to the Internet (set IP and router address) Turn off customer feedback. Set up internet address. Decline to use a Smart Host for email. Added one standard user account. Since this happened again and I was very careful the second time not to configure anything outside of the SBS Console, I feel like there's something else going on. Right now the machine is on an isolated network that does have internet access. My desktop is the only other machine plugged into this network. Any and all help is appreciated (before I tear my hair out!)

  Read the article

• GeForce 8800GT not even giving basic output

  - by Sam

  My Dad bought a GeForce 8800GT graphics card quite a long time ago now. It has never worked in his PC. Print out from a dxdiag: System Information Time of this report: 4/13/2010, 19:52:40 Machine name: USER-PC Operating System: Windows Vista™ Home Premium (6.0, Build 6001) Service Pack 1 (6001.vistasp1_gdr.091208-0542) Language: English (Regional Setting: English) System Manufacturer: To Be Filled By O.E.M. System Model: To Be Filled By O.E.M. BIOS: Default System BIOS Processor: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz (4 CPUs), ~2.3GHz Memory: 2046MB RAM Page File: 1045MB used, 3296MB available Windows Dir: C:\Windows DirectX Version: DirectX 10 DX Setup Parameters: Not found DxDiag Version: 6.00.6001.18000 32bit Unicode DxDiag Notes Display Tab 1: No problems found. Sound Tab 1: No problems found. Sound Tab 2: No problems found. Sound Tab 3: No problems found. Input Tab: No problems found. DirectX Debug Levels Direct3D: 0/4 (retail) DirectDraw: 0/4 (retail) DirectInput: 0/5 (retail) DirectMusic: 0/5 (retail) DirectPlay: 0/9 (retail) DirectSound: 0/5 (retail) DirectShow: 0/6 (retail) Display Devices Card name: ATI Radeon HD 2400 PRO Manufacturer: ATI Technologies Inc. Chip type: ATI Radeon Graphics Processor (0x94C3) DAC type: Internal DAC(400MHz) Device Key: Enum\PCI\VEN_1002&DEV_94C3&SUBSYS_00000000&REV_00 Display Memory: 1012 MB Dedicated Memory: 245 MB Shared Memory: 767 MB Current Mode: 1280 x 960 (32 bit) (75Hz) Monitor: Generic PnP Monitor Driver Name: atiumdag.dll,atiumdva.dat,atitmmxx.dll Driver Version: 7.14.0010.0523 (English) DDI Version: 10 Driver Attributes: Final Retail Driver Date/Size: 8/22/2007 02:43:14, 3021312 bytes That info is from the current card that is installed in it and has been installed since its purchase roughly 3-4 years ago. When I physically install the card I put it into a purple slot on the motherboard that the old card was in (if I go into the device manager and select properties on the current card it confirms that the slot is a "PCI Slot 16 (PCI bus 2, device 0, function 0)") and boot up the computer but get absolutely no output. The screen that we have registers that it is connected to something (by not displaying the screen it does when the cable is unplugged) but just remains blank, no output at all. I recently took the card to my University and one of my friends who is better with hardware issues than I am tried it in his system and it worked perfectly. No issues whatsoever. I do not have a spec list for his system but I could get one if you need it. If you need any more information on this issue I will be happy to supply you with it as I am starting to get very annoyed with this problem ^_^

  Read the article

• lighttpd: weird behavior on multiple rewrite rule matches

  - by netmikey

  I have a 20-rewrite.conf for my php application looking like this: $HTTP["host"] =~ "www.mydomain.com" { url.rewrite-once += ( "^/(img|css)/.*" => "$0", ".*" => "/my_app.php" ) } I want to be able to put the webserver in kind of a "maintenance" mode while I update my application from scm. To do this, my idea was to enable an additional rewrite configuration file before this one. The 16-rewrite-maintenance.conf file looks like this: url.rewrite-once += ( "^/(img|css)/.*" => "$0", ".*" => "/maintenance_app.php" ) Now, on the maintenance page, I have a logo that doesn't get loaded. I get a 404 error. Lighttpd debug says the following: 2012-12-13 20:28:06: (response.c.300) -- splitting Request-URI 2012-12-13 20:28:06: (response.c.301) Request-URI : /img/content/logo.png 2012-12-13 20:28:06: (response.c.302) URI-scheme : http 2012-12-13 20:28:06: (response.c.303) URI-authority: localhost 2012-12-13 20:28:06: (response.c.304) URI-path : /img/content/logo.png 2012-12-13 20:28:06: (response.c.305) URI-query : 2012-12-13 20:28:06: (response.c.300) -- splitting Request-URI 2012-12-13 20:28:06: (response.c.301) Request-URI : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.302) URI-scheme : http 2012-12-13 20:28:06: (response.c.303) URI-authority: localhost 2012-12-13 20:28:06: (response.c.304) URI-path : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.305) URI-query : 2012-12-13 20:28:06: (response.c.349) -- sanatising URI 2012-12-13 20:28:06: (response.c.350) URI-path : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (mod_access.c.135) -- mod_access_uri_handler called 2012-12-13 20:28:06: (response.c.470) -- before doc_root 2012-12-13 20:28:06: (response.c.471) Doc-Root : /www 2012-12-13 20:28:06: (response.c.472) Rel-Path : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.473) Path : 2012-12-13 20:28:06: (response.c.521) -- after doc_root 2012-12-13 20:28:06: (response.c.522) Doc-Root : /www 2012-12-13 20:28:06: (response.c.523) Rel-Path : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.524) Path : /www/img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.541) -- logical -> physical 2012-12-13 20:28:06: (response.c.542) Doc-Root : /www 2012-12-13 20:28:06: (response.c.543) Rel-Path : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.544) Path : /www/img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.561) -- handling physical path 2012-12-13 20:28:06: (response.c.562) Path : /www/img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.618) -- file not found 2012-12-13 20:28:06: (response.c.619) Path : /www/img/content/logo.png, /img/content/logo.png Any clue on why lighttpd matches both rules (from my application rewrite config and from my maintenance rewrite config) and concatenates them with a comma - that doesn't seem to make any sense?! Shouldn't it stop after the first match with rewrite-once?

  Read the article

• High I/O latency with software RAID, LUKS encrypted and LVM partitioned KVM setup

  - by aef

  I found out a performance problems with a Mumble server, which I described in a previous question are caused by an I/O latency problem of unknown origin. As I have no idea what is causing this and how to further debug it, I'm asking for your ideas on the topic. I'm running a Hetzner EX4S root server as KVM hypervisor. The server is running Debian Wheezy Beta 4 and KVM virtualisation is utilized through LibVirt. The server has two different 3TB hard drives as one of the hard drives was replaced after S.M.A.R.T. errors were reported. The first hard disk is a Seagate Barracuda XT ST33000651AS (512 bytes logical, 4096 bytes physical sector size), the other one a Seagate Barracuda 7200.14 (AF) ST3000DM001-9YN166 (512 bytes logical and physical sector size). There are two Linux software RAID1 devices. One for the unencrypted boot partition and one as container for the encrypted rest, using both hard drives. Inside the latter RAID device lies an AES encrypted LUKS container. Inside the LUKS container there is a LVM physical volume. The hypervisor's VFS is split on three logical volumes on the described LVM physical volume: one for /, one for /home and one for swap. Here is a diagram of the block device configuration stack: sda (Physical HDD) - md0 (RAID1) - md1 (RAID1) sdb (Physical HDD) - md0 (RAID1) - md1 (RAID1) md0 (Boot RAID) - ext4 (/boot) md1 (Data RAID) - LUKS container - LVM Physical volume - LVM volume hypervisor-root - LVM volume hypervisor-home - LVM volume hypervisor-swap - … (Virtual machine volumes) The guest systems (virtual machines) are mostly running Debian Wheezy Beta 4 too. We have one additional Ubuntu Precise instance. They get their block devices from the LVM physical volume, too. The volumes are accessed through Virtio drivers in native writethrough mode. The IO scheduler (elevator) on both the hypervisor and the guest system is set to deadline instead of the default cfs as that happened to be the most performant setup according to our bonnie++ test series. The I/O latency problem is experienced not only inside the guest systems but is also affecting services running on the hypervisor system itself. The setup seems complex, but I'm sure that not the basic structure causes the latency problems, as my previous server ran four years with almost the same basic setup, without any of the performance problems. On the old setup the following things were different: Debian Lenny was the OS for both hypervisor and almost all guests Xen software virtualisation (therefore no Virtio, also) no LibVirt management Different hard drives, each 1.5TB in size (one of them was a Seagate Barracuda 7200.11 ST31500341AS, the other one I can't tell anymore) We had no IPv6 connectivity Neither in the hypervisor nor in guests we had noticable I/O latency problems According the the datasheets, the current hard drives and the one of the old machine have an average latency of 4.12ms.

  Read the article

• Kernel upgrade CentOS 5.3 mount: could not find filesystem '/dev/root'

  - by matt

  We have a CentOS 5.3 x64 server that by default runs kernel version 2.6.18-164.11.1 and we are attempting to upgrade the box to 2.6.31.12 The drive is LVM +ext3, and the problem I'm having is when I upgrade the kernel and attempt to boot from it, no matter what version of the kernel I use, I get /dev/root not found towards the end of the boot process, and the kernel panics, and than reboots. I'm installing the kernel exactly as it says in this doc. I've tried it "The centOS way " using make rpm and than installing that. I've updated my mkinitrd. The most interesting part of this problem is that it has been so frustrating that I decided to try and clean install centos on an identical machine without LVM, and the result is EXACTLY the same. After upgrading the kernel, I get /dev/root not found. Does anyone know how to fix this, or what information would be relevant to remedy it? I'm open to try anything at this point. One more interesting thing about this problem is that in the new version of the kernel, during boot it complains that dm-mapper is started twice, than panics right after that. I've tried this with other kernel versions, and the result is the same. What am I missing here? If you need any more files, please just ask. Linux cg 2.6.18-164.11.1.el5 #1 SMP Wed Jan 20 07:32:21 EST 2010 x86_64 x86_64 x86_64 GNU/Linux /dev/VolGroup00/LogVol00 / ext3 defaults 1 1 LABEL=/boot /boot ext3 defaults 1 2 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 /dev/VolGroup00/LogVol01 swap swap defaults 0 0 default=1 timeout=5 splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu title CentOS (2.6.31.12-rt20) //NOT WORKING!!!! root (hd0,0) kernel /vmlinuz-2.6.31.12-rt20 ro root=/dev/VolGroup00/LogVol00 isolcpus=8,9,10,11,12,13,14,15 panic=10 initrd /initrd-2.6.31.12-rt20.img title CentOS (2.6.18-164.11.1.el5) //WORKING!! root (hd0,0) kernel /vmlinuz-2.6.18-164.11.1.el5 ro root=/dev/VolGroup00/LogVol00 isolcpus=8,9,10,11,12,13,14,15 panic=10 initrd /initrd-2.6.18-164.11.1.el5.img

  Read the article

• Windows cannot find the host name "download.microsoft.com" using DNS

  - by joedotnot

  When trying to download a file found on the Microsoft downloads center that starts with, for example, http://download.microsoft.com/download/6/8/7/(some_GUID)/(some_file_name.ext) i get a timeout with "Internet Explorer cannot display the webpage". More information says: Internet connectivity has been lost. The website is temporarily unavailable. The Domain Name Server (DNS) is not reachable. The Domain Name Server (DNS) does not have a listing for the website's domain. If this is an HTTPS (secure) address, click Tools, click Internet Options, click Advanced, and check to be sure the SSL and TLS protocols are enabled under the security section. Diagnose Connection problems says: Windows cannot find the host name "download.microsoft.com" using DNS Bear with me while i expand on the problem: It all started when i tried to download Windows XP mode for my Windows 7 machine. I went to the virtual PC site, then thru the motions of Windows Genuine Advantage which validated ok, but when it redirects to grab the file just times out with above error. (NB: i also tried with the latest Chrome and Firefox but no use due to the Genuine Advantage stuff, so i decided to stick with IE). I am behind an ADSL2+ modem router connecting via wireless (Win 7 Pro laptop); so i hop over to the desktop connected via ethernet (Vista Business), and same result; begin to think site download.microsoft.com site is down. So i give it a break an read up on EDNS, flushing the cache, hosts file, etc... Try again an hour later on the Win 7 machine, still no go; so i turn off the Win 7 (software) firewall, and lo and behold, i can connect and grab any files from download.microsoft.com; (...nice, so we have a Micro$0ft firewall preventing access to a Micro$0ft website, no wonder my auto-updates kept failing but that's another story). But i still am not happy that the desktop connected via ethernet still cannot get to download.microsoft.com, even though i turned off all firewalls, defenders, anti-virus, etc. What is so special / specific about the url download.microsoft.com, any other site is ok, including www.microsoft.com. Any networking guru know what's REALLY going on, and how can i get the desktop to connect? Ping download.microsoft.com - Ping request could not find host download.microsoft.com. Please check the name and try again. Ping google.com or even www.microsoft.com works gives me an IP address. NB: On the wireless laptop ping download.microsoft.com works, i get xxxx.ms.akamai.net [202.7.177.33].

  Read the article

• OpenLDAP with StartTLS broken on Debian Lenny

  - by mr.zog

  I'm trying to get OpenLDAP on Lenny to work with StartTLS. I have a Fedora 13 machine which I'm using as a client for testing. So far the Fedora client is ignoring the 'host' directive in /etc/ldap.conf when I try to connect using ldapsearch. The client wants to connect to 127.0.0.1:389 even if I specify -H ldaps://server.name on when using ldapsearch. /etc/ldap.conf on the client machine is in mode 444. But even when I try connecting locally from an ssh session, I see errors like this: ldap_sasl_interactive_bind_s: Can't contact LDAP server (-1) Someone hit me with a cluebat, plz. Update: you must use ~/.ldaprc for settings such as 'host'. Also, I just used nmap against the ldap server and it showed 636 and 389 in an open state. Here's what prints to screen when I try to connect with, ldapsearch -ZZ –x '(objectclass=*)'+ -d -1 ldap_create ldap_extended_operation_s ldap_extended_operation ldap_send_initial_request ldap_new_connection 1 1 0 ldap_int_open_connection ldap_connect_to_host: TCP 192.168.10.41:636 ldap_new_socket: 3 ldap_prepare_socket: 3 ldap_connect_to_host: Trying 192.168.10.41:636 ldap_pvt_connect: fd: 3 tm: -1 async: 0 ldap_open_defconn: successful ldap_send_server_request ber_scanf fmt ({it) ber: ber_dump: buf=0x9bdbdb8 ptr=0x9bdbdb8 end=0x9bdbdd7 len=31 0000: 30 1d 02 01 01 77 18 80 16 31 2e 33 2e 36 2e 31 0....w...1.3.6.1 0010: 2e 34 2e 31 2e 31 34 36 36 2e 32 30 30 33 37 .4.1.1466.20037 ber_scanf fmt ({) ber: ber_dump: buf=0x9bdbdb8 ptr=0x9bdbdbd end=0x9bdbdd7 len=26 0000: 77 18 80 16 31 2e 33 2e 36 2e 31 2e 34 2e 31 2e w...1.3.6.1.4.1. 0010: 31 34 36 36 2e 32 30 30 33 37 1466.20037 ber_flush2: 31 bytes to sd 3 0000: 30 1d 02 01 01 77 18 80 16 31 2e 33 2e 36 2e 31 0....w...1.3.6.1 0010: 2e 34 2e 31 2e 31 34 36 36 2e 32 30 30 33 37 .4.1.1466.20037 ldap_write: want=31, written=31 0000: 30 1d 02 01 01 77 18 80 16 31 2e 33 2e 36 2e 31 0....w...1.3.6.1 0010: 2e 34 2e 31 2e 31 34 36 36 2e 32 30 30 33 37 .4.1.1466.20037 ldap_result ld 0x9bd3050 msgid 1 wait4msg ld 0x9bd3050 msgid 1 (infinite timeout) wait4msg continue ld 0x9bd3050 msgid 1 all 1 ** ld 0x9bd3050 Connections: * host: 192.168.10.41 port: 636 (default) refcnt: 2 status: Connected last used: Sun Jun 6 12:54:05 2010 ** ld 0x9bd3050 Outstanding Requests: * msgid 1, origid 1, status InProgress outstanding referrals 0, parent count 0 ld 0x9bd3050 request count 1 (abandoned 0) ** ld 0x9bd3050 Response Queue: Empty ld 0x9bd3050 response count 0 ldap_chkResponseList ld 0x9bd3050 msgid 1 all 1 ldap_chkResponseList returns ld 0x9bd3050 NULL ldap_int_select read1msg: ld 0x9bd3050 msgid 1 all 1 ber_get_next ldap_read: want=8, got=0 ber_get_next failed. ldap_err2string ldap_start_tls: Can't contact LDAP server (-1)

  Read the article

• How could I let Skydrive desktop sync to MicroSD in Windows 8 tablet?

  - by peSHIr

  I have a Samsung Slate 7 tablet with (now) Windows 8 on it. This machine has a 64 Gb SSD and I have a 64 Gb MicroSD card in it. I also have a Skydrive on my main Microsoft ID that contains about 45 Gb of content. With Windows and some development stuff installed, my Skydrive will not fit on the main drive of the tablet. (Besides, my idea was to keep data on the memory card anyway, to make it easier to repave the machine without data loss if need be.) My problem should now be clear: I want to install the Skydrive desktop app to sync my Skydrive to the MicroSD card. This is not possible, as Skydrive does not allow syncing files to removable drives. I have tried a number of things already, but none of them worked: Use the mklink command line tool to create a directory link/junction from a folder name on SSD to a folder on the MicroSD and then try to install Skydrive sync to the SSD link folder. Skydrive however still recognizes this as something it does not want to sync onto. The various different filter drivers mentioned on Agnipulse (including the Hitachi one) that should make windows see some or all of the removable drives in the system as fixed drives do not seem work on (64-bit) Windows 8: they either can't be installed, do nothing and/or cause Windows 8 to go into Automatic Repair mode when rebooting. The Lexar BootIt app seems to be meant to flip the relevant bit in the on-board drive controller of supported USB pen drives, but I tried it anyway. Of course it did nothing to how the MicroSD card was seen. I have now run out of ideas, it seems, and I was wondering if anyone here has a solution to let Windows 8 see the MicroSD memory card in my tablet as a fixed drive instead of removable drive, or some other way of getting the Skydrive desktop to sync my Skydrive data to that MicroSD card. And to be complete: this is not a duplicate question of this or this as those ask about getting USB drives multiple partitions to work on Windows XP. This question is specific about getting desktop Skydrive to sync to MicroSD card in Windows 8, which seems to be a question I have not seen on superuser so far.

  Read the article

• Problems when trying to connect to a router wirelessly

  - by Ruud Lenders

  The situation - At my girlfriend's parents' place there are six Windows 7 devices that are wired or wireless connected to a router: 3 dekstops and 3 laptops. There are also several smartphones using the router. The router is secured with WPA2 (AES). The problem - We never had any problems with the router for over a year. But recently - about 3 weeks ago - my girlfriend's laptop (HP) and my laptop (ASUS) started to develop problems while trying to connect to the router. The router has stopped showing up from the network list. Sometimes it comes back and shows up, but then it keeps saying something along the lines of "Could not connect", and not long after that it dissapears again. The range of the router is not the problem here, because we experience the same when we sit next to the router. Sometimes, if we are lucky, and waited a long time (10-15 minutes) without using the laptop for anything, the laptop will eventually succesful connect to the router. The attempts - Of course, the Window 7 troubleshooter. We tried troubleshooting the connection problems and the wireless network adapter, but no luck. We also reset the router enough times to know that's not helping either. Here's the full list of things we tried, but did not help: Running the Windows 7 troubleshooter Resetting the router (more than once) Setting the router settings to factory defaults Disconnecting all other devices except one laptop Applying a system restore Trying static/dynamic IP/DNS - Dynamic is better, right? Enabling/disabling IPv6 - Should I keep IPv6 disabled? Running the command: netsh wlan stop hostednetwork Running the command: netsh wlan set hostednetwork mode=disallow Updating/reïnstalling wireless adapter drivers The tests - To help finding the core of the problem, we tested the following: Plugging an ethernet cable in the router and in our laptops - worked fine Connecting someone else's laptop to the router (wireless) - worked fine Connecting our laptops to someone else's router - worked fine The router - This information might be relevant: Router model: Sitecom 300N Wireless Router Router hardware: version 01 The DCHP Server's IPs range from 192.168.0.100 to 192.168.0.200. Router settings: Wireless channel: 12 Channel bandwidth: 20/40 MHz Extension channel: 8 Preamble type: Long 802.11g protection: Disabled UPnP: Enabled The laptops - If you are wondering about our laptops: My laptop model: ASUS Pro64JQ Girlfriend's laptop: HP Pavillion G6 OS: Both Windows 7 Professional x64 - with Service Pack 1 My wireless adapter: Atheros AR9285 AdHoc 11n: Enabled The question - Does anyone have experienced the same problems as I do? Or does someone know how to solve this? Are there more tricks I can try, or settings I should change? Note - Our laptops are not slow or old. My laptop is 1.5 years old, and the other laptop is just 5 months old. I know how to keep laptops clean and I'm pretty sure both laptops are not bloated with useless software.

  Read the article

• lacp, cicso 3550, 3560, help with configuration

  - by Flamewires

  Hey all this is a repost from a question I asked on the cisco forums but never got a useful reply. Hey I'm trying to convert the FreeBSD servers at work to dual-gig lagg links from regular gigabit links. Our production servers are on a 3560. I have a small test environment on a 3550. I have achieved fail-over, but am having troubles achieving the speed increase. All servers are running gig intel (em) cards. The configs for the servers are: BSDServer: #!/bin/sh #bring up both interfaces ifconfig em0 up media 1000baseTX mediaopt full-duplex ifconfig em1 up media 1000baseTX mediaopt full-duplex #create the lagg interface ifconfig lagg0 create #set lagg0's protocol to lacp, add both cards to the interface, #and assign it em1's ip/netmask ifconfig lagg0 laggproto lacp laggport em0 laggport em1 ***.***.***.*** netmask 255.255.255.0 The switches are configured as follows: #clear out old junk no int Po1 default int range GigabitEthernet 0/15 - 16 # config ports interface range GigabitEthernet 0/15 - 16 description lagg-test switchport duplex full speed 1000 switchport access vlan 192 spanning-tree portfast channel-group 1 mode active channel-protocol lacp **** switchport trunk encapsulation dot1q **** no shutdown exit interface Port-channel 1 description lagginterface switchport access vlan 192 exit port-channel load-balance src-mac end obviously change 1000's to 100's and GigabitEthernet to FastEthernet for the 3550's config, as that switch has 100Mbit speed ports. With this config on the 3550, I get failover and 92Mbits/sec speed on both links, simultaneously, connecting to 2 hosts.(tested with iperf) Success. However this is only with the "switchport trunk encapsulation dot1q" line. First, I do not understand why I need this, I thought it was only for connecting switches. Is there some other setting which this turns on that is actually responsible for the speed increase? Second, This config does not work on the 3560. I get failover, but not the speed increase. Speeds drop from gig/sec to 500Mbit/sec when I make 2 simultaneous connections to the server with or without the encapsulation line. I should mention that both switches are using source-mac load balancing. In my test I am using Iperf. I have the server(lagg box) setup as the server(iperf -s), and the client computers are client(iperf -c server-ip-address), so the source mac(and IP) are different for both connections. Any ideas/corrections/questions would be helpful, as the gig switches are what I actually need the lagg links on. Ask if you need more information.

  Read the article

• Why MySQL sat for 2 minutes doing nothing?

  - by Alex R

  This was a one-time thing, not reproducible... But I saved the show innodb status output. Can anybody tell what's going on here? The simple insert took almost 3 minutes to complete. | InnoDB | | ===================================== 110201 15:58:10 INNODB MONITOR OUTPUT ===================================== Per second averages calculated from the last 34 seconds ---------- SEMAPHORES ---------- OS WAIT ARRAY INFO: reservation count 11963, signal count 11766 --Thread 1824 has waited at .\btr\btr0cur.c line 443 for 118.00 seconds the sema phore: S-lock on RW-latch at 09D6453C created in file .\buf\buf0buf.c line 550 a writer (thread id 1824) has reserved it in mode wait exclusive number of readers 1, waiters flag 1 Last time read locked in file .\buf\buf0flu.c line 599 Last time write locked in file .\btr\btr0cur.c line 443 Mutex spin waits 0, rounds 527817, OS waits 7133 RW-shared spins 2532, OS waits 1226; RW-excl spins 1652, OS waits 1118 ------------ TRANSACTIONS ------------ Trx id counter 0 95830 Purge done for trx's n:o < 0 95814 undo n:o < 0 0 History list length 11 LIST OF TRANSACTIONS FOR EACH SESSION: ---TRANSACTION 0 0, not started, OS thread id 3704 MySQL thread id 551, query id 2702112 localhost 127.0.0.1 root show innodb status ---TRANSACTION 0 95829, not started, OS thread id 3132 MySQL thread id 534, query id 2702020 localhost 127.0.0.1 root ---TRANSACTION 0 95828, not started, OS thread id 3152 MySQL thread id 527, query id 2701973 localhost 127.0.0.1 root ---TRANSACTION 0 95827, ACTIVE 118 sec, OS thread id 1824 inserting, thread decl ared inside InnoDB 500 mysql tables in use 1, locked 1 1 lock struct(s), heap size 320, 0 row lock(s) MySQL thread id 526, query id 2701972 localhost 127.0.0.1 root update INSERT INTO log_searchcriteria (userid,search_criteria,date,search_type) VALUES ( NAME_CONST('userid',NULL), NAME_CONST('search_criteria',_latin1' SELECT SQL_C ALC_FOUND_ROWS idx_search.CTCX_LATITUDE, idx_search.CTCX_LONGITUDE, idx_search.b uilding_id, idx_search.LN_LIST_NUMBER, idx_search.LP_LIST_PRICE, idx_search.HSN_ ADRESS_HOUSE_NUMBER, idx_search.STR_ADDRESS_STREET, idx_search.CP_ADDRESS_COMPAS S_POINT, idx_search.UN_UNIT, idx_search.CIT_CITY, idx_search.ZP_ZIP_CODE, idx_se arch.AR_AREA_NAME, idx_search.BR_BEDROOMS, idx_search.BTH_BATHS, idx_search.ST_S TATUS, idx_search.CTCX_STYLE_TYPE, idx_s -------- FILE I/O -------- I/O thread 0 state: wait Windows aio (insert buffer thread) I/O thread 1 state: wait Windows aio (log thread) I/O thread 2 state: wait Windows aio (read thread) I/O thread 3 state: wait Windows aio (write thread) Pending normal aio reads: 0, aio writes: 1, ibuf aio reads: 0, log i/o's: 0, sync i/o's: 0 Pending flushes (fsync) log: 0; buffer pool: 0 151006 OS file reads, 120758 OS file writes, 6844 OS fsyncs 0.00 reads/s, 0 avg bytes/read, 0.00 writes/s, 0.00 fsyncs/s ------------------------------------- INSERT BUFFER AND ADAPTIVE HASH INDEX ------------------------------------- Ibuf: size 1, free list len 5, seg size 7, 24664 inserts, 24664 merged recs, 4612 merges Hash table size 553253, node heap has 629 buffer(s) 0.00 hash searches/s, 0.00 non-hash searches/s --- LOG --- Log sequence number 5 2318193115 Log flushed up to 5 2318193115 Last checkpoint at 5 2318129891 0 pending log writes, 0 pending chkp writes 3036 log i/o's done, 0.00 log i/o's/second ---------------------- BUFFER POOL AND MEMORY ---------------------- Total memory allocated 213459462; in additional pool allocated 1720192 Dictionary memory allocated 240416 Buffer pool size 8192 Free buffers 0 Database pages 7563 Modified db pages 18 Pending reads 0 Pending writes: LRU 0, flush list 18, single page 0 Pages read 150973, created 28788, written 115137 0.00 reads/s, 0.00 creates/s, 0.00 writes/s No buffer pool page gets since the last printout -------------- ROW OPERATIONS -------------- 1 queries inside InnoDB, 0 queries in queue 1 read views open inside InnoDB Main thread id 2992, state: flushing buffer pool pages Number of rows inserted 794294, updated 89203, deleted 13698, read 1453084305 0.00 inserts/s, 0.00 updates/s, 0.00 deletes/s, 0.00 reads/s ---------------------------- END OF INNODB MONITOR OUTPUT ============================ Thanks

  Read the article

• unable to join domain using virtualbox

  - by FreshPrinceOfSO

  I'm in the process of setting up a VM environment for a MS certification exam (70-462). Following the training kit's instructions, I've set up a domain controller (DC) and two members (SQL-A, SQL-B) thus far. I can't figure out why I can't join the domain. DC IPv4 Address . . . : 10.10.10.10(Preferred) Subnet Mask. . . . : 255.0.0.0 DNS Servers. . . . : ::1 127.0.0.1 SQL-A IPv4 Address . . . : 10.10.10.20(Preferred) Subnet Mask. . . . : 255.0.0.0 DNS Servers. . . . : 10.10.10.10 SQL-B IPv4 Address . . . : 10.10.10.30(Preferred) Subnet Mask. . . . : 255.0.0.0 DNS Servers. . . . : 10.10.10.10 I've read how to do networking between virtual machines in virtualbox and the documentation. After trying various network adapter configurations, I can't get them to communicate in order to have the two members join the domain. When I ping from .30 to .10, I get: ping 10.10.10.10 Pinging 10.10.10.10 with 32 bytes of data: Reply from 10.10.10.20: Destination host unreachable. Reply from 10.10.10.20: Destination host unreachable. Reply from 10.10.10.20: Destination host unreachable. Reply from 10.10.10.20: Destination host unreachable. Trying to join the domain: netdom join SQL-A /domain:contso.com The specified domain either does not exist or could not be contacted. The command failed to complete successfully. Within VirtualBox, I've tried the following combinations for network adapter: Attached to - Promiscuous Mode ------------------------------- NAT Bridged Adapter - Deny Bridged Adapter - Allow VMs Bridged Adapter - Allow All Internal Network - Deny Internal Network - Allow VMs Internal Network - Allow All Host-only Adapter - Deny Host-only Adapter - Allow VMs Host-only Adapter - Allow All Edit ipconfig /all of DC ipconfig /all of SQL-A

  Read the article

• amd gpu but display on intel integrated graphics

  - by pitseeker

  On my Ubuntu 12.04 I connected my monitor to the onboard intel graphics. I'd like to use my ati radeon 6770 for opencl tasks (e.g. bitcoin mining). So far I couldn't figure out how to get the ati driver working. When calling "aticonfig --initial -f" it always writes a new xorg.conf that ignores the intel graphics. At boot time it works only when I attached the monitor to the ati card. So I manually tampered with the xorg.conf and got this: Section "ServerLayout" Identifier "Default Monitor" Screen 0 "myscreen" 0 0 Screen 1 "deadscreen" RightOf "myscreen" EndSection Section "Module" EndSection Section "Monitor" Identifier "Default Monitor" Option "VendorName" "Monitor Vendor" Option "ModelName" "Monitor Name" Option "DPMS" "true" EndSection Section "Monitor" Identifier "null Monitor" Option "Enable" "false" EndSection Section "Device" Identifier "Intel Integrated Graphics" Driver "intel" BusID "PCI:0:2:0" Screen 0 EndSection Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:0:0" Screen 1 EndSection Section "Screen" Identifier "myscreen" Device "Intel Integrated Graphics" Monitor "Default Monitor" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "deadscreen" Device "aticonfig-Device[0]-0" Monitor "null Monitor" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection I think this might be the right way since I see that X tries to start both drivers in /var/log/Xorg.0.log. However the fglrx driver seems crash (end of xorg.0.log): Backtrace: [ 6.625] 0: /usr/bin/X (xorg_backtrace+0x26) [0x7fb5cd41b846] [ 6.625] 1: /usr/bin/X (0x7fb5cd293000+0x18c6ea) [0x7fb5cd41f6ea] [ 6.625] 2: /lib/x86_64-linux-gnu/libpthread.so.0 (0x7fb5cc5b9000+0xfcb0) [0x7fb5cc5c8cb0] [ 6.625] 3: /usr/lib/x86_64-linux-gnu/xorg/extra-modules/extra-modules.dpkg-tmp/modules/drivers/fglrx_drv.so (xdl_xs111_atiddxGetGPUMapInfo+0x1b1) [0x7fb5c88e16b1] [ 6.625] 4: /usr/lib/x86_64-linux-gnu/xorg/extra-modules/extra-modules.dpkg-tmp/modules/drivers/fglrx_drv.so (atiddxGetGPUMapInfo+0xd) [0x7fb5c87bcc0d] [ 6.625] 5: /usr/lib/x86_64-linux-gnu/xorg/extra-modules/extra-modules.dpkg-tmp/modules/extensions/libglx.so (0x7fb5ca12d000+0x1ab29) [0x7fb5ca147b29] [ 6.625] 6: /usr/lib/x86_64-linux-gnu/xorg/extra-modules/extra-modules.dpkg-tmp/modules/extensions/libglx.so (0x7fb5ca12d000+0x1cf8c) [0x7fb5ca149f8c] [ 6.625] 7: /usr/lib/x86_64-linux-gnu/xorg/extra-modules/extra-modules.dpkg-tmp/modules/extensions/libglx.so (0x7fb5ca12d000+0x1ee55) [0x7fb5ca14be55] [ 6.626] 8: /usr/bin/X (InitExtensions+0x99) [0x7fb5cd350069] [ 6.626] 9: /usr/bin/X (0x7fb5cd293000+0x3d605) [0x7fb5cd2d0605] [ 6.626] 10: /lib/x86_64-linux-gnu/libc.so.6 (__libc_start_main+0xed) [0x7fb5cb44e76d] [ 6.626] 11: /usr/bin/X (0x7fb5cd293000+0x3daad) [0x7fb5cd2d0aad] [ 6.626] Segmentation fault at address 0x14 [ 6.626] Caught signal 11 (Segmentation fault). Server aborting [ 6.626] I'd be very happy if someone can give me a hint on how to configure my ATI card while using the integrated graphics for display. Update I used most of jjhughes57 config and successfully booted the X server on intel (keyboard layout is changed though, funnily). Unfortunately the 2nd X server (fglrx) doesn't fully start. It shuts itself down right after starting [ 6.265] (II) fglrx(0): Restoring Recent Mode via PCS is not supported in RANDR 1.2 capable environments [ 6.296] (II) UnloadModule: "mouse" [ 6.296] (II) Unloading mouse [ 6.296] (II) UnloadModule: "kbd" [ 6.296] (II) Unloading kbd [ 6.298] (II) fglrx(0): Shutdown CMMQS [ 6.298] (II) fglrx(0): [uki] removed 1 reserved context for kernel [ 6.298] (II) fglrx(0): [uki] unmapping 8192 bytes of SAREA 0x2000 at 0x7fbef8209000 [ 6.337] (II) fglrx(0): Interrupt handler Shutdown. [ 6.470] ddxSigGiveUp: Closing log [ 6.470] Server terminated successfully (0). Closing log file. Thanks for any hints what is wrong here.

  Read the article

• Why does NX Client for Windows silently closes after connection?

  - by pavel

  Hey! I connect remotely to my Ubuntu server from Vista machine. Now I need to run a GUI application on the server (Wireshark). So I decided to use FreeNX server/client to view Ubuntu GUI on Vista I have successfully installed FreeNX on Ubuntu and NX Client on Vista. I was following this guide Unfortunately, now I found myself stuck with the following problem. At the client, the !M logo window appears, but after a few seconds that window just closes, even without showing any error message. Guys, I'm really stuck, please help! Maybe I should have installed some graphical environment on the server? These are the details from NX client, it seems there are no errors. ----------------- Info: Display running with pid '7768' and handler '0x670d24'. NXPROXY - Version 3.4.0 Copyright (C) 2001, 2007 NoMachine. See http://www.nomachine.com/ for more information. Info: Proxy running in client mode with pid '2168'. Session: Starting session at 'Sat Dec 19 10:58:35 2009'. Warning: Connected to remote version 3.3.0 with local version 3.4.0. Info: Connection with remote proxy completed. Info: Using WAN link parameters 768/24/1/0. Info: Using cache parameters 4/4096KB/16384KB/16384KB. Info: Using pack method 'adaptive-9' with session 'kde'. Info: Using ZLIB data compression 1/1/32. Info: Using ZLIB stream compression 1/1. Info: No suitable cache file found. Info: Forwarding X11 connections to display ':0'. Info: Listening to font server connections on port '11000'. Session: Session started at 'Sat Dec 19 10:58:35 2009'. Info: Established X server connection. Info: Using shared memory parameters 0/0K. Session: Terminating session at 'Sat Dec 19 10:58:37 2009'. Session: Session terminated at 'Sat Dec 19 10:58:37 2009'. -----------

  Read the article

• ssh refuses to authenticate keys

  - by MixturaDementiae

  So I am setting up a connection between my machine [fedora 17] and a virtual machine running in Virtual Box in which is running CentOS 5. I have installed openssh from the repositories on CentOS, and I have configured everything as it follows: Protocol 2 HostKey /etc/ssh/ssh_host_rsa_key HostKey /etc/ssh/ssh_host_dsa_key SyslogFacility AUTHPRIV PermitRootLogin yes RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile /home/pigreco/.ssh/authorized_keys PasswordAuthentication no ChallengeResponseAuthentication yes GSSAPIAuthentication yes GSSAPICleanupCredentials yes UsePAM yes AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL LANGUAGE AcceptEnv XMODIFIERS X11Forwarding yes Subsystem sftp /usr/libexec/openssh/sftp-server this is the configuration file sshd_config on the server i.e. on the CentOS. Moreover I have created a public/private key pair as usual on the .ssh/ folder in my home directory in my OS, i.e. Fedora, and then I've copied with scp the id_rsa.pub to the server and then I have appended its content to the file .ssh/authorized_keys on the server machine. The error that I get is the following: OpenSSH_5.9p1, OpenSSL 1.0.0j-fips 10 May 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 50: Applying options for * debug1: Connecting to 192.168.100.13 [192.168.100.13] port 22. debug1: Connection established. debug1: identity file /home/mayhem/.ssh/identity type -1 debug1: identity file /home/mayhem/.ssh/identity-cert type -1 debug1: identity file /home/mayhem/.ssh/id_rsa type 1 debug1: identity file /home/mayhem/.ssh/id_rsa-cert type -1 debug1: identity file /home/mayhem/.ssh/id_dsa type -1 debug1: identity file /home/mayhem/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3 debug1: match: OpenSSH_5.3 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 16:e5:72:d1:37:94:1b:5e:3d:3a:e5:da:6f:df:0c:08 debug1: Host '192.168.100.13' is known and matches the RSA host key. debug1: Found key in /home/mayhem/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,keyboard-interactive debug1: Next authentication method: gssapi-keyex debug1: No valid Key exchange context debug1: Next authentication method: gssapi-with-mic debug1: Unspecified GSS failure. Minor code may provide more information Cannot determine realm for numeric host address debug1: Unspecified GSS failure. Minor code may provide more information Cannot determine realm for numeric host address debug1: Unspecified GSS failure. Minor code may provide more information debug1: Unspecified GSS failure. Minor code may provide more information Cannot determine realm for numeric host address debug1: Next authentication method: publickey debug1: Offering RSA public key: /home/mayhem/.ssh/id_rsa debug1: Server accepts key: pkalg ssh-rsa blen 279 Agent admitted failure to sign using the key. debug1: Trying private key: /home/mayhem/.ssh/identity debug1: Trying private key: /home/mayhem/.ssh/id_dsa debug1: Next authentication method: keyboard-interactive Do you have some good suggestion of what I can do? thank you

  Read the article

• Missing startup screens and slow bootup/login after using WinClone to expand Bootcamp partition

  - by user26453

  I used WinClone to backup my Bootcamp partition, which was a Windows 7 Ultimate install, on my late 2006 Macbook Pro. I desired to expand the Bootcamp partition's size. It worked reasonably well with some hiccups along the way and some remaining issues. First issue I ran into was the Bootcamp Assistant utility - it would not recreate the partition. This was due to a lack of contiguous space that is required for the Bootcamp partition. As a result I wiped the whole drive and reinstalled Snow Leopard, did the minimum amount of system updates, and created and formated a new Bootcamp partition. WinClone restored the image without complaint and the image was automatically resized to the new partition's size. Second issue I ran into was after the first boot into Windows. The first thing I noticed was that instead of the newer "slick" startup screen (4 colors wisping around, a Windows 7 title), there was more of an old school style startup screen (a progress bar with block increments, yellow/greenish color, nothing else really). The initial bootup to a login screen was slow, perhaps as Windows dealt with the partition changes. After logging in, the screen goes blank and the computer seems to hang for a minute, before completing the login. After subsequent restarts, the slick screen is still missing, boot to login screen is normal, but the time from login to desktop active is still very slow. As a side note, this behavior of a long time from login to the desktop finally loaded I've previously only seen when the computer would try to hibernate and fail (battery is really bad). On the next startup, I would see this behavior, but not subsequently. So a potential cause: I imaged the partition after hibernating out of Windows. From reading some posts/guides on the subject, this was not recommended, and perhaps shouldn't even have worked? Could the partition be stuck in some weird mode as a result that makes the boot issues appear? I've attempted to disable hibernation and restart, trying to delete the .sys file that hibernation uses. Other fixes I'm thinking of attempting are booting a Win7 disc and repairing the install/partition. I can't shake the nagging feeling something isn't right as a result of the modified boot screens and the slow login process.

  Read the article

< Previous Page | 393 394 395 396 397 398 399 400 401 402 403 404  | Next Page >