Search Results

Search found 13329 results on 534 pages for 'email addresses'.

Page 411/534 | < Previous Page | 407 408 409 410 411 412 413 414 415 416 417 418  | Next Page >

• Inconsistent DHCP replies with Windows 2008R2 DHCP server

  - by verbalicious

  I've got a Windows 2008R2 standard server running DHCP services. We've noticed that certain clients are receiving inconsistent DHCP replies. We have over 175 Windows workstations in this VLAN that don't seem to have trouble getting DHCP leases. However, PXE-booting clients trying to reach our DHCP server are able to get a lease inconsistently. Additionally, we tried using the "dhcping" tool against our DHCP server and found that roughly two of every three requests time out with "no answer" -- and this holds true when we set the timeout value on dhcping to 20seconds. After a failed attempt, however, we may get a dhcp lease reply immediately with dhcping. This leads me to believe that this issue isn't confined to PXE booting clients, but something more systemic with my LAN layer2 or DHCP. And that possibly my 175 windows clients are experiencing this in some form without my knowledge. We have over 30% of our scope available so the addresses are there. I was unable to find anything in the Windows server "DHCP-Server" log. Of course, my goal is to have my DHCP server reply to every request that it receives on the LAN!

  Read the article

• Single computer on network cannot connect to internet.

  - by user34630

  Hi All, I hope you can help me out! :) I have 3 computers and one device (Xbox) on my home network; 2 running XP and one on Vista. The computer that can't connect to the internet (XP) is old and failing, and shows no warning before it completely runs out of battery. Thus today, I started it up forgetting that I had unplugged it the night before, and it just ran out of battery entirely whilst I was using it and died. I think that before this I had been browsing the internet, but I can't remember for certain. (i.e. The problem I am having may or may not have been caused by this 'hard' power off). Anyway, now when I start the computer up it takes 5-10 minutes after logging on to display the start bar and icons. Also, I cannot browse the internet. The computer seems to connect to the network OK (I have tried both wired and wireless), but I can't visit sites and can't ping web addresses. Pinging the router fails, as does pinging another of my computers on the network. I have never encountered something like this before, and whilst I am no noob I am also not a sysadmin, haha. :( Any help is greatly appreciated, thank you for your time. P.S. I have tried a system restore (newbie move?).

  Read the article

• Setting up PerformancePoint Services on Sharepoint 2010: connection errors

  - by Rik

  I have tried to setup PerformancePoint Services on SharePoint 2010, but every time I try to use the dashboard designer, I get this error: “An error has occurred attempting to contact the specified SharePoint site” I have tried these steps but it hasn't helped. Any ideas? The event log gives the following information: WebHost failed to process a request. Sender Information: System.ServiceModel.ServiceHostingEnvironment+HostingManager/24724999 Exception: System.ServiceModel.ServiceActivationException: The service '/_vti_bin/client.svc' cannot be activated due to an exception during compilation. The exception message is: This collection already contains an address with scheme http. There can be at most one address per scheme in this collection. Parameter name: item. --- System.ArgumentException: This collection already contains an address with scheme http. There can be at most one address per scheme in this collection. Parameter name: item at System.ServiceModel.UriSchemeKeyedCollection.InsertItem(Int32 index, Uri item) at System.Collections.Generic.SynchronizedCollection`1.Add(T item) at System.ServiceModel.UriSchemeKeyedCollection..ctor(Uri[] addresses) at System.ServiceModel.ServiceHost..ctor(Type serviceType, Uri[] baseAddresses) at System.ServiceModel.Activation.ServiceHostFactory.CreateServiceHost(Type serviceType, Uri[] baseAddresses) at System.ServiceModel.Activation.ServiceHostFactory.CreateServiceHost(String constructorString, Uri[] baseAddresses) at System.ServiceModel.ServiceHostingEnvironment.HostingManager.CreateService(String normalizedVirtualPath) at System.ServiceModel.ServiceHostingEnvironment.HostingManager.ActivateService(String normalizedVirtualPath) at System.ServiceModel.ServiceHostingEnvironment.HostingManager.EnsureServiceAvailable(String normalizedVirtualPath) --- End of inner exception stack trace --- at System.ServiceModel.ServiceHostingEnvironment.HostingManager.EnsureServiceAvailable(String normalizedVirtualPath) at System.ServiceModel.ServiceHostingEnvironment.EnsureServiceAvailableFast(String relativeVirtualPath) Process Name: w3wp Process ID: 2576

  Read the article

• How do I stop postfix from handling my mail?

  - by Tatu Ulmanen

  Here's the situation: I have a domain, let's say domain.com. That domain has Google Apps for Business enabled, so all mail delivered to @domain.com will end up at Google (MX records point to Google). I have a PHP script at domain.com that I use to send mail to myself. But when the PHP script tries to send mail to [email protected], Postfix at that server decides that the recipient is a local user (because the address matches the domain Postfix itself is at), and tries to deliver the mail locally. But inevitably fails as the mailbox cannot be found. How can I instruct Postfix to not try to handle locally any emails to @domain.com and just send them forward so Google can pick them up? I have already removed $myhostname from mydestination field in Postfix's main.cf file, and I have restarted Postfix but Postfix still tries to deliver the mail locally. Here's a snip from mail.log that show the problem (addresses replaced): postfix/pickup[20643]: AF718422E5: uid=33 from=<server> postfix/cleanup[20669]: AF718422E5: message-id=<62e706bcca5a0de0bfec6baa576d88a5@server> postfix/qmgr[20642]: AF718422E5: from=<server>, size=517, nrcpt=1 (queue active) postfix/pipe[20678]: AF718422E5: to=<[email protected]>, relay=dovecot, delay=0.62, delays=0.47/0.03/0/0.13, dsn=5.1.1, status=bounced (user unknown) postfix/bounce[20680]: AF718422E5: sender non-delivery notification: 29598422E7 postfix/qmgr[20642]: AF718422E5: removed

  Read the article

• "Safe" personal router use on apartment-wide network

  - by noisetank

  I recently moved into an apartment with internet included in my rent. This was a boon at first, but now I'm feeling limited. To get devices connected (wired or wireless), I have to whitelist the MAC addresses on mycampusnet.com. This is annoying (considering I'm well over the 10 device limit including my roommate's stuff), but what's really driving me mad is that I don't seem to have any semblance of a "local" network. I've relied heavily on static IPs and port forwarding in the past (accessing NAS and remote desktop) and (as far as I can understand), that functionality is nonexistent without my router set up. Also, as my wired and wireless devices don't always seem to make it onto the same subnet, I'm unable to use any of my iDevices with my Apple TV (I can, however, mirror to no less than four strangers' Apple TVs at any moment, which is a whole other level of discomforting). I've talked to the head of the apartment complex and she told me that they personally don't have any issue with my using a router, but the provider (CampusConnect) does not currently allow it. Apparently, enough people have put in complaints/requests about the restriction (the apartments are for graduate students and University staff, many of which need to set up things like VPNs for work reasons) to open up some sort of ticket to get the functionality in place, but all the calls I've made to get status updates have been a waste of time. My question is: If I plugged my router into the apartment network, what would happen? I've been told already that personal routers would "interfere with the wireless" and that they would shut my port down if I used one, but is that a legitimate thing or just something made up that sounds real to keep the average Joe from pushing it further? I'm guessing there's some way of configuring my router to keep it from disrupting the rest of the network, but it's not something they want to tell me for obvious reasons. Am I right? And if so, what are the chances that they'd notice the difference in traffic or whatever and shut off my port?

  Read the article

• Connection refused in ssh tunnel to apache forward proxy setup

  - by arkascha

  I am trying to setup a private forward proxy in a small server. I mean to use it during a conference to tunnel my internet access through an ssh tunnel to the proxy server. So I created a virtual host inside apache-2.2 running the proxy, the proxy_http and the proxy_connect module. I use this configuration: <VirtualHost localhost:8080> ServerAdmin xxxxxxxxxxxxxxxxxxxx ServerName yyyyyyyyyyyyyyyyyyyy ErrorLog /var/log/apache2/proxy-error_log CustomLog /var/log/apache2/proxy-access_log combined <IfModule mod_proxy.c> ProxyRequests On <Proxy *> # deny access to all IP addresses except localhost Order deny,allow Deny from all Allow from 127.0.0.1 </Proxy> # The following is my preference. Your mileage may vary. ProxyVia Block ## allow SSL proxy AllowCONNECT 443 </IfModule> </VirtualHost> After restarting apache I create a tunnel from client to server: #> ssh -L8080:localhost:8080 <server address> and try to access the internet through that tunnel: #> links -http-proxy localhost:8080 http://www.linux.org I would expect to see the requested page. Instead a get a "connection refused" error. In the shell holding open the ssh tunnel I get this: channel 3: open failed: connect failed: Connection refused Anyone got an idea why this connection is refused ?

  Read the article

• How does Linux determine the SCSI address of a disk?

  - by Chris Sears

  Greetings, I'm working with RHEL 5.5 guest VMs under VMware ESX 4. When I configure the virtual disks in the VM hardware settings, each disk has a SCSI address in the format "N:M". For example, "1:3" would mean SCSI host number 1 and SCSI target ID 3. When I look at the disk info from the VM's BIOS or a Windows OS, the detected SCSI address info matches up with the virtual hardware settings. But under Linux, the SCSI address components don't match up, at least not completely or consistently. I've tried the three supported virtual SCSI and SAS drivers and they all seem to be "broken", but in different ways. Here's a list of the virtual hardware addresses vs what was detected under Linux with each of the drivers: Driver vHW Addr Linux Addr -------- -------- ---------- LSI SAS 0:0 0:0 LSI SAS 0:3 0:1 LSI SAS 0:6 0:2 LSI SCSI 1:1 2:1 LSI SCSI 1:4 2:4 LSI SCSI 1:7 2:7 pvSCSI 2:2 1:2 pvSCSI 2:5 1:5 pvSCSI 2:8 1:8 My main question is why does this happen under Linux? The next question is: how do I get it fixed or fix it myself? If I was going to guess, I'd say it's an issue with how the kernel is handing out the SCSI host number and how the Linux SCSI driver (included with VMware tools) is detecting the SCSI target number. Perhaps the order the drivers are loaded also has something to do with the issue. I'm guessing this would not involve udev, but I could be wrong. Any thoughts would be appreciated. Thanks! PS. My environment is VMware, but I don't need an answer for these drivers specifically. I imagine this might be a problem with any SCSI driver under Linux.

  Read the article

• postfix smtp_fallback_relay for deferred messages to a single domain

  - by EdwardTeach

  I use Postfix to send messages to a mail server outside my organization which frequently rejects/defers my mail. My Postfix server sees that these messages are deferred and tries again, eventually getting through. Final delivery can take up to an hour, which makes my users unhappy. In comparison, mail from my Postfix server to other hosts works normally. I have now found out about a second, unofficial MX for this domain that does not reject/defer mail. This second MX does not appear when doing a DNS MX query for the domain. Therefore, for the problem domain I would like to use this second MX as a fallback. That is: whenever mail is deferred by the primary MX, try again on the unofficial second MX. I see that there is already a postfix configuration "smtp_fallback_relay". However the documentation seems to indicate that I can not restrict usage of the fallback to a single domain. The documentation also doesn't mention deferred message handling. So is there a way to configure a single-domain, deferred-retry fallback host in Postfix? For reference, I am including my postconf output (the host names and ip addresses are fake): alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases, hash:/etc/postfix/legacy_mailman, ldap:/etc/postfix/ldap-aliases.cf append_dot_mydomain = no biff = no config_directory = /etc/postfix default_destination_concurrency_limit = 2 inet_interfaces = all inet_protocols = all local_destination_concurrency_limit = 2 local_recipient_maps = $alias_maps mailbox_size_limit = 0 mydestination = myhost.my.network, localhost.my.network, localhost, my.network myhostname = myhost.my.network mynetworks = 127.0.0.0/8, [::ffff:127.0.0.0]/104, [::1]/128, 10.10.10.0/24 myorigin = my.network readme_directory = no recipient_delimiter = + relay_domains = $mydestination relayhost = smtp_fallback_relay = the.problem.host smtp_header_checks = smtpd_banner = $myhostname ESMTP $mail_name virtual_alias_maps = hash:/etc/postfix/virtual

  Read the article

• postfix smtpd rejecting mail from outside network match_list_match: no match

  - by Loopo

  My postfix (V: 2.5.5-1.1) running on ubuntu server (9.04) started to reject mail arriving in from outside about 2 weeks ago. Doing a "manual" session via telnet shows that the connection is always closed after the MAIL FROM: [email protected] line is input, with the message "Connection closed by foreign host." Doing the same from another client inside the LAN works fine. In the log files I get the line "lost connection after MAIL from xxxxx.tld[xxx.xxx.xxx.xxx]" This is after some lines like: match_hostaddr: XXX.XXX.XXX.XXX ~? [::1]/128 match_hostname: XXXX.tld ~? 192.168.1.0/24 ... match_list_match: xxx.xxx.xxx.xxx: no match which seem to suggest some kind of filter which checks for allowed addresses. I have been unable to locate where this filter lives, or how to turn it off. I'm not even sure if that's what's causing my problem. Connections from inside the LAN don't get disconnected even though they also show a "match_list_match: ... no match" line. I didn't change any configuration files recently, below is my main.cf as it currently stands. I don't really know what all the parameters do and how they interact. I just set it up initially and it worked fine (up to recently). smtpd_banner = $myhostname ESMTP $mail_name (GNU) biff = no readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/server.crt smtpd_tls_key_file=/etc/ssl/private/server.key #smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_sasl_auth_enable = no smtp_use_tls=no smtp_sasl_password_maps = hash:/etc/postfix/smtp_auth myhostname = XXXXXXX.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = XXXX.XXXX.com, XXXX.com, localhost.XXXXX.com, localhost relayhost = XXX.XXX.XXX.XXX mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 192.168.1.0/24 mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all smtpd_sasl_local_domain = #smtpd_sasl_auth_enable = yes smtpd_sasl_security_options = noanonymous smtpd_sasl_authenticated_header = yes broken_sasl_auth_clients = yes smtpd_recipient_restrictions = permit_mynetworks,permit_sasl_authenticated,reject_unauth_ when checking the process list, postfix/smtpd runs as smtpd -n smtp -t inet -u -c -o stress -v -v Any clues?

  Read the article

• How to fake ip at localhost without LoopBack.

  - by sexer

  How can i fake an ip on my own PC? for example if there were an ip address lets say 201.91.81.71, that Host is somewhere outside of my red and is hosting a webserver. How can set a website on my own PC, and when i go to browser and try to explore 201.91.81.71 it actually explore the website at my own PC? pd: I need it with IP addresses not domain names, since I need to implement it on a non-web service. First guess was installing a LoopBack with 201.191.81.71 as ip, but since some times the subnet works and some other it doesn't isn't a stable solution. Second guess was adding a route to route table : route add 201.91.81.71 mask 255.255.255.255 192.168.1.2 192.168.1.2 is the ip address of my NIC. If i could add this route it would work but windows doesn't let me do so. route add 201.91.81.71 mask 255.255.255.255 127.0.0.1 it doesn't let me set as gateway 127.0.0.1 if 201.91.81.71 isn't set in a NIC, so thats why i set sometimes loopback and this route add is auto, but it needs a subnet mask which doesn't match the ip and cannot set 255.255.255.255, im in real throubles here. can i get some help? thx.

  Read the article

• Enabling mod_wsgi in Apache for a Django app on Gentoo

  - by hobbes3

  I installed Apache, Django, and mod_wsgi on Gentoo using emerge (on Amazon EC2). I know that the mod_wsgi is configured in /etc/apache2/modules.d/70_mod_wsgi.conf: <IfDefine WSGI> LoadModule wsgi_module modules/mod_wsgi.so </IfDefine> # vim: ts=4 filetype=apache So in my /etc/conf.d/apache I added the WSGI module: APACHE2_OPTS="-D DEFAULT_VHOST -D INFO -D SSL -D SSL_DEFAULT_VHOST -D LANGUAGE -D WSGI" But when I try to list the loaded module, mod_wsgi isn't listed. root ~ # apache2 -M | grep wsgi Syntax OK I also know that mod_wsgi isn't loading properly because the Apache configuration file doesn't recognize WSGIScriptAlias. By the way for Django to work I need to include a custom Apache configuration file. Where should I insert the line below? Include "/var/www/localhost/htdocs/mysite/apache/apache_django_wsgi.conf" I currently have that in the httpd.conf file but I feel like that file will get reseted whenever I upgrade Gentoo or related package. EDIT: it seems the mod_wsgi file is located in /usr/lib64/apache2/modules/mod_wsgi.so. Here is my detailed Apache settings: root@ip-99-99-99-99 /usr/portage/eclass # apache2 -V Server version: Apache/2.2.21 (Unix) Server built: Mar 7 2012 06:52:30 Server's Module Magic Number: 20051115:30 Server loaded: APR 1.4.5, APR-Util 1.3.12 Compiled using: APR 1.4.5, APR-Util 1.3.12 Architecture: 64-bit Server MPM: Prefork threaded: no forked: yes (variable process count) Server compiled with.... -D APACHE_MPM_DIR="server/mpm/prefork" -D APR_HAS_SENDFILE -D APR_HAS_MMAP -D APR_HAVE_IPV6 (IPv4-mapped addresses enabled) -D APR_USE_SYSVSEM_SERIALIZE -D APR_USE_PTHREAD_SERIALIZE -D APR_HAS_OTHER_CHILD -D AP_HAVE_RELIABLE_PIPED_LOGS -D DYNAMIC_MODULE_LIMIT=128 -D HTTPD_ROOT="/usr" -D SUEXEC_BIN="/usr/sbin/suexec" -D DEFAULT_PIDLOG="/var/run/httpd.pid" -D DEFAULT_SCOREBOARD="logs/apache_runtime_status" -D DEFAULT_LOCKFILE="/var/run/accept.lock" -D DEFAULT_ERRORLOG="logs/error_log" -D AP_TYPES_CONFIG_FILE="/etc/apache2/mime.types" -D SERVER_CONFIG_FILE="/etc/apache2/httpd.conf"

  Read the article

• DNS stops working occasionally

  - by Andrey

  I have tried using Google DNS and the one provided with DHCP. At some point my PC (Windows 7) stops resolving domain names, but DNS server is perfectly pingable. What can be the reason? Thanks! Edit: It is really weird. It can stop and start working in few seconds. The problem is that DNA requests are timing out, and the problem is that the DNS server is pingable at the same time. I can't understand how this could be possible and what might be an issue. C:\Windows\System32\drivers\etc>nslookup google.com DNS request timed out. timeout was 2 seconds. Server: UnKnown Address: 8.8.8.8 Non-authoritative answer: Name: google.com Addresses: 173.194.78.102 173.194.78.101 173.194.78.139 173.194.78.113 173.194.78.100 173.194.78.138 C:\Windows\System32\drivers\etc>nslookup google.com DNS request timed out. timeout was 2 seconds. Server: UnKnown Address: 8.8.8.8 DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. *** Request to UnKnown timed-out

  Read the article

• Valid IP address but can't surf without rebooting

  - by Kat

  I periodically lose internet and router connection at home. When this happens, others are using the router just fine. I am connecting directly through a wired connection to a Belkin router. I can release and renew the IP (and the IP addresses change to 0.0.0.0 and to an IP in my router's range beginning with 192.168.2. as they should) but still can't surf, can't access the router interface. Cycling the router doesn't help, and again, others are able to access the router fine at this time. Only rebooting the computer resolves the issue, and everything is wonderful for a few hours- and then I lose connection again. I have several ideas where to go from here, but I'd like to get some advice first. (Using Windows XP SP3, hardwired connection) Update As stated in the originally, releasing and renewing doesn't solve the issue. However, I have an update. I can ping localhost and my router IP with no problem at all when the issue occurs. However, repairing the network connection does not help. I AM able to get back on by disabling and then re-enabling the network connection in XP. What does that tell us?

  Read the article

• Exchange Connector Won't Send to External Domains

  - by sisdog

  I'm a developer trying to get my .Net application to send emails out through our Exchange server. I'm not an Exchange expert so I'll qualify that up front!! We've set up a receive Connector in Exchange that has the following properties: Network: allows all IP addresses via port 25. Authentication: Transport Layer Security and Externally Secured checkboxes are checked. Permission Groups: Anonymous Users and Exchange Servers checkboxes are checked. But, when I run this Powershell statement right on our Exchange server it works when I send to a local domain address but when I try to send to a remote domain it fails. WORKS: C:\Windows\system32Send-Mailmessage -To [email protected] -From [email protected] -Subject testing -Body testing -SmtpServer OURSERVER (BTW: my value for OURSERVER=boxname.domainname.local. This is the same fully-qualified name that shows up in our Exchange Management Shell when I launch it). FAILS: C:\Windows\system32Send-Mailmessage -To [email protected] -From [email protected] -Subject testing -Body testing -SmtpServer OURSERVER Send-MailMessage : Mailbox unavailable. The server response was: 5.7.1 Unable to relay At line:1 char:17 + Send-Mailmessage <<<< -To [email protected] -From [email protected] -Subject testing -Body himom -SmtpServer FTI-EX + CategoryInfo : InvalidOperation: (System.Net.Mail.SmtpClient:SmtpClient) [Send-MailMessage], SmtpFailed RecipientException + FullyQualifiedErrorId : SmtpException,Microsoft.PowerShell.Commands.SendMailMessage EDIT: From @TheCleaner 's advice, I ran the Add-ADPermission to the relay and it didn't help; [PS] C:\Windows\system32Get-ReceiveConnector "Allowed Relay" | Add-ADPermission -User "NT AUTHORITY\ANONYMOUS LOGON" -E xtendedRights "Ms-Exch-SMTP-Accept-Any-Recipient" Identity User Deny Inherited -------- ---- ---- --------- FTI-EX\Allowed Relay NT AUTHORITY\ANON... False False Thanks for the help. Mark

  Read the article

• PC won't PXE boot to WDS/MDT with Dell Optiplex 755

  - by Moman10

  I am trying to set up a basic MDT solution. I have set one up in the past at a previous job and it worked flawlessly, however here I'm running into a problem and am having no luck getting around it. I've installed Windows Server 2012 and MDT 2013, along with adding on the WDS role. I haven't configured much outside of the defaults for WDS, basically just set PXE response to respond to all clients (and unchecked admin approval). This machine does not run a DHCP server. I looked on the DHCP scope of our DHCP server, it shows options 66/67 checked and the server name of the WDS server is in there as well. I didn't add this but I assume it was put on during the install process (I believe I had to manually make some adjustments at my old job for this). The PC I have is a Dell Optiplex 755. I have enabled the onbard NIC w/PXE boot option in BIOS and attempted to boot. I get a "TFTP...." error but nothing offering out a DHCP address like I'm used to. In my previous job it pretty much worked right out of the box. I've verified that PortFast is enabled on the port and I've tried a couple different PCs (but both are the same model, only model I have to work with). No matter what, I get the same error. The subnet the PC is in is a different subnet than where the WDS server is sitting, but there are IP helper statements on the switch and the PCs can get regular DHCP addresses just fine from the DHCP server, just doesn't seem to get offered out a PXE boot option. I don't know if the problem is a configuration with the server or the PC itself...but after a few days of Googling I'm running out of ideas. Does anyone have a good idea of something it may be?

  Read the article

• Can Subject Alternative Name accommodate multiple virtual mail domains?

  - by Lawrence

  I am currently running a postfix server with self signed certificates serving one mail domain, mycompany.com, the mail server is mail.mycompany.com and so is the CN of the certificate. Now, I need to add a new domain to it. The new domain name is mycompany.net to the same server. Since the users already have the root of the old certificate, I'd like to reuse that. However, I'd like to issue a new certificate so users using the SMTP from Outlook/Thunderbird of mail.mycompany.net do not get warnings. If I understand correctly, if I issue a new certificate with CN=mail.mycompany.com and a subjectAltName=DNS:mail.mydomain.net and have postfix serve this, the client will not complain either way about the cn not matching the target host name. Am I correct in this assumption or am I misunderstanding the concept of Subject Alternative Name? Just to avoid conversation, I do not want to have users on mycompany.net addresses use the mycompany.com server because I might (not a technical issue) have to split up into two different locations, and I want to produce an easily migrateable setup.

  Read the article

• lighttpd with multiple IPs, each with a UCC certificate and many hostnames

  - by Dave

  I'd like to get lighttpd working with UCC certificates, but I can't seem to figure out the correct syntax. Essentially, for each IP address, I have one UCC certificate and a bunch of hostnames. $SERVER["socket"] == "10.0.0.1:443" { ssl.engine = "enable" ssl.ca-file = "/etc/ssl/certs/the.ca.cert.pem" ssl.pemfile = "/etc/ssl/private/websitegroup1.com.pem" $HTTP["host"] =~ "mywebsite.com" { server.document-root = /var/www/mywebsite.com/htdocs" } The above code works fine for one hostname, but as soon as I try to set up another hostname (note the same SSL cert): $SERVER["socket"] == "10.0.0.1:443" { ssl.engine = "enable" ssl.ca-file = "/etc/ssl/certs/the.ca.cert.pem" ssl.pemfile = "/etc/ssl/private/websitegroup1.com.pem" $HTTP["host"] =~ "anotherwebsite.com" { server.document-root = /var/www/anotherwebsite.com/htdocs" } ...I get this error: Duplicate config variable in conditional 6 global/SERVERsocket==10.0.0.1:443: ssl.engine Is there any way I can put a conditional so that only if ssl.engine is not already enabled, enable it? Or do I have to put all my $HTTP["host"]s inside the same $SERVER["socket"] (which will make config file management more difficult for me) or is there some entirely different way to do it? This has to be repeated for multiple IPs too (so I'll have a bunch of SERVER["socket"] == 10.0.0.2:443" etc), each with one UCC cert and many hostnames. Am I going about this the wrong way entirely? My goal is to conserve IP addresses when I have many websites that are related and can share an SSL certificate, but still need their own SSL-accessible version from the appropriate hostname (instead of a single secure.mywebsite.com).

  Read the article

• Sharepoint Central Administration stuck / high CPU usage

  - by johnnyb10

  I'm using WSS 3 and I recently added a new web application to my SharePoint Server. After adding it, I wasn't able to open the Central Administration site. I also noticed that there was a w3wp.exe error (Event ID 1000) in the Event Viewer. The situation now is that the w3wp.exe process is hovering around 50% CPU usage continuously. I installed a program called IIS Peek, and it shows continuous GET requests on the Central Administration site; this happens even if I stop the Central Administration site in IIS. The IP addresses identified in the GET request is my workstation, which is what I used to attempt to access Central Administration after I created the new web application. Can someone explain what's going on and how I might fix it? It seems as if my computer tried to access Central Administration and then it hung, but the page requests that were happening at the time are somehow continuing over and over again. So my two problems are the inability to access Central Administration, and the CPU Usage of w3wp.exe, which I'm assuming are two symptoms of the same problem. I'd like to know if there's anything I can do besides restarting IIS, because we have clients accessing other sites on this server. Thanks.

  Read the article

• How can I tell my dd-wrt router to use someone's Amazon Affiliates link when I point my browser to amazon.com?

  - by Michael Paul

  Here's what I'd like to do. Instead of a one-time donation to one of my favorite free tools (junecloud.com) I'd like to do what they suggest here and use their Amazon Affiliates link to do all my Amazon shopping. I shop at amazon once or twice a week, so this is a great way to let them earn lots of long-term cash without me dropping a dime. My thought was to go into my dd-wrt enabled router and tell it, "any time I go to amazon.com on any computer in the house, please go to http://www.amazon.com/gp/redirect.html?link_code=ur2&tag=junecloud-20&camp=1789&creative=9325&location=%2F instead. (That URL simply redirects me to amazon.com but every purchase I make during that session is credited to JuneCloud.) Once logged into dd-wrt, I went to Services Services DNSMasq but I'm not really sure how to get it to work from there, or if it's even possible. I know I can redirect IP addresses, but I'm looking to redirect someone on my network from amazon.com to the special amazon affiliate code link. Hope that's clear. Thanks for any replies!

  Read the article

• finding the best network latency between two countries

  - by Yoav Aner

  I know there are many tools to test for bandwidth and latency, but they all rely on having at least one host from which you can run those tests. I wonder whether there's an online source or some other way to guestimate the latency or speed between two countries (in general). For example, would a customer in Japan get lower latency if the server is located in Singapore or Australia? Is a user in India likely to get higher download speed from a server in the UK or in the US? Are there any online resources or some clever ways to answer those questions with a reasonable degree of accuracy? [UPDATE]: Thanks for the great suggestions from Raffael Luthiger. I didn't know about those looking glass servers. The submarine cable maps were also really cool to discover (Thanks to Jesper Mortensen). Also seems really wise if I could ask those network professional in the area for their experience, but obviously I don't have access to those. At least some of them are on SF :) However, I'm still a little unsure how to combine those resources to give me some measurements. This is the information I have: Two countries (A,B). I do have IP addresses of customers in country A (I can obtain those from the web server log files for example). Presumably I can find some looking glass servers in country B and run a trace to those IPs. What's the best measurements to use? Are there any scripts that help automate at least some of this process?

  Read the article

• 530 5.7.1 Client was not authenticated Exchange 2010 for some computers within mask

  - by user1636309

  We have a classic problem with Client not Authenticated but with a specific twist: We have an Exchange 2010 cluster, let's say EX01 and EX02, the connection is always to smtp.acme.com, then it is switched through load balancer. We have an application server, call it APP01 There are clients connected to the APP01. There is a need for anonymous mail relay from both clients and APP01. The Anonymous Users setting of the Exchange is DISABLED, but the specific computers - APP01 and clients by the mask, let's say, 192.168.2.* - are enabled. For internal relay, a "Send Connector" is created, and then the above IP addresses are added for the connector to allow computers, servers, or any other device such as a copy machine to use the exchange server to relay email to recipients. The problem is that the relay works for APP01 and some clients, but not others (we get "Client not Authenticated") - all inside the same network and the same mask. This is basically what we do to test it outside of our application: http://smtp25.blogspot.sk/2009/04/530-571-client-was-not-authenticated.html So, I am looking for ideas: What can be the reason for such a strange behaviour? Where I can see the trace of what's going on at the Exchange side?

  Read the article

• Options for small windows network setup without dedicated server?

  - by Mitch

  I'm very weak on networking and hope someone can point me in the right direction: I have written some windows client/server software which incorporates a database which is located on a windows server. I have a test installation running at a customer's office where the server has a static IP address. In this case its easy for the clients to access the database because of the fixed IP address. Also, customers with network servers generally have specialist support staff to set up my software, so its not such a problem for me. However I also need to offer the software to customers who have small offices with less than 10 PCs and no dedicated network server. In this case I want the customer to be able to nominate one PC as the database "server" and install my software and have the clients access it. But in this situation I believe the "server" PC may not have a dedicated IP address. Q1: What is the best way to set this up simply and make it work? Can I reliably reference the "server" by using its name, or is there a way to assign dummy fixed IP addresses? Ideally this needs to be workable on small networks running a mixture of XP/Vista/Windows7 as my target market may well have mixed OSes etc. I guess this would be akin to home networking? Many thanks Mitch

  Read the article

• Tomcat Solr times out

  - by user568458

  (Plesk 10.4 centos 5.8 linux apache2 server, with Tomcat5 on port 8080 and Apache Solr) I get "The connection has timed out" on requesting domain.com:8080 or www.domain.com:8080 or ip.ad.dr.ess:8080 Every reason I can find why this might be seems not to be the case: Plesk thinks Tomcat is running fine and lists it as an active service. The firewall currently has an accept all rule on port 8080. There's nothing relevant in the catalina tomcat logs (/var/log/tomcat5) - just some stuff from last time tomcat was started. There's no record at all of the requests that fail. netstat -lnp | grep 8080 gives the following, which I beleive means Tomcat is listening to requests to port 8080 on all ip addresses from any ip and any port (please correct me if I'm wrong): : tcp 0 0 0.0.0.0:8080 0.0.0.0:* LISTEN 4018/java This covers every cause of this time out that I can find - so I must be missing something fundamental. It seems Tomcat is running, listening to the right port, is getting an appropriate IP address, is not obstructed by a firewall and is not failing after receiving a request in a way which would be recorded in the logs (so I believe it can't be out of memory, or anything like that). I'm all out of ideas on how to continue debugging this. I must have overlooked something obvious. Can anyone help?

  Read the article

• mod_rpaf with apache error_log

  - by Camden S.

  I'm using mod-rpaf with Apache 2.4 and it's working properly (showing the real client IP's) in my Apache access_log... but not in my error_log. My error log just shows the client IP address of the proxy server (my load balancer in this case) Here's an example of what I see in my error_log where 123.123.123.123 is the IP of my load balancer/proxy. == /usr/local/apache2/logs/error_log <== [Tue Jun 05 20:24:31.027525 2012] [access_compat:error] [pid 9145:tid 140485731845888] [client 123.123.123.123:20396] AH01797: client denied by server configuration: /wwwroot/private/secret.pdf The exact same request produces the following in my access_log where 456.456.456.456 is a real client IP (not the IP of the load balancer). 456.456.456.456 - - [05/Jun/2012:20:24:31 +0000] "GET /wwwroot/private/secret.pdf HTTP/1.1" 403 228 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10.7; rv:12.0) Gecko/20100101 Firefox/12.0" Here's my httpd.conf entry: # RPAF LoadModule rpaf_module modules/mod_rpaf-2.0.so RPAFenable On RPAFproxy_ips 127.0.0.1 123.123.123.123 RPAFsethostname On RPAFheader X-Forwarded-For What do I need to do to get the real IP addresses showing in my Apache error_log?

  Read the article

• When modern computers boot, what initial setup of RAM do they execute, and how does it exactly work?

  - by user272840

  I know the title reeks of confusion, and some of you might assume I am just wondering about how the computer boots in general, but I'm not. But I'll sort this out for you people now: 1.Onboard firmware is how mostly all modern computer devices work, whether or not with EFI/UEFI(even without "onboard firmware", older computers still employed bank switching, or similar methods with snap-in firmware, cartridges, etc.) 2.On startup there is no "programs" running in the traditional sense yet, i.e. no kernel, OS, user-applications; all of the instructions, especially the very first instruction, is specified by the Instruction Pointer, I am guessing. How is the IP/PC/etc. set to first point to an address for a BIOS/firmware/etc. instruction, and how do the BIOS instructions map themself out in memory prior to startup? 3.Aside from MMIO, BIOS uses certain RAM addresses to have instructions. The big ? comes in when I ask this ... how does BIOS do this? Conclusion: I am assuming that with the very first instruction there is an initial hardware setup for BIOS prior to complete OS bootup. What I want to know is if it's hardware engineered to always work this way, if there's another step in this bootup method I am missing, a gap of information I am unaware of, or how this all works from the very first instruction, and the RAM data itself.

  Read the article

< Previous Page | 407 408 409 410 411 412 413 414 415 416 417 418  | Next Page >