Search Results

Search found 13329 results on 534 pages for 'email addresses'.

Page 413/534 | < Previous Page | 409 410 411 412 413 414 415 416 417 418 419 420  | Next Page >

• Is it possible to change an "Unidentified Network" into a "Home" or "Work" network on Windows 7

  - by Rhys

  I have a problem with Windows 7 RC (7100). I frequently use a crossover network cable on WinXP with static IP addresses to connect to various industrial devices (e.g. robots, pumps, valves or even other Windows PCs) that have Ethernet network ports. When I do this on Windows 7, the network connection is classed as an "Unidentified Network" in Networks and Sharing Center and the public firewall profile is enforced by Windows. I do not want to change the public profile and would prefer to use the Home or Work profile instead. For other networks like Home and Work I'm able to click on them and change the classification. This is not available for unidentified networks. My questions are these:- Is there a way to manual override the "Unidentified Network" classification? What tests are performed on the network that fail, therefore classifying it as an "Unidentified Network" By googling (hitting mainly vista issues) it seems that you need to ensure that the default gateway is not 0.0.0.0. I've done this. I've also tried to remove IPv6 but this does not seem possible on Windows 7.

  Read the article

• PTR and A record must match?

  - by somecallmemike

  RFC 1912 Section 2.1 states the following: Make sure your PTR and A records match. For every IP address, there should be a matching PTR record in the in-addr.arpa domain. If a host is multi-homed, (more than one IP address) make sure that all IP addresses have a corresponding PTR record (not just the first one). Failure to have matching PTR and A records can cause loss of Internet services similar to not being registered in the DNS at all. Also, PTR records must point back to a valid A record, not a alias defined by a CNAME. It is highly recommended that you use some software which automates this checking, or generate your DNS data from a database which automatically creates consistent data. This does not make any sense to me, should an ISP keep matching A records for every PTR record? It seems to me that it's only important if the IP address that the PTR record describes is hosting a service that is sensitive to DNS being mismatched (such as email hosting). In that case the forward zone would be configured under a domain name (examples follow the format 'zone - record'): domain.tld -> mail IN A 1.2.3.4 And the PTR record would be configured to match: 3.2.1.in-addr.arpa -> 4 IN PTR mail.domain.tld. Would there be any reason for the ISP to host a forward lookup for an IP address on their network like this?: ispdomain.tld -> broadband-ip-1 IN A 1.2.3.4

  Read the article

• Cisco 3560+ipservices -- IGMP snooping issue with TTL=1

  - by Jander

  I've got a C3560 with Enhanced (IPSERVICES) image, routing multicast between its VLANs with no external multicast router. It's serving a test environment where developers may generate multicast traffic on arbitrary addresses. Everything is working fine except when someone sends out multicast traffic with TTL=1, in which case the multicast packet suppression fails and the traffic is broadcast to all members of the VLAN. It looks to me like because the TTL is 1, the multicast routing subsystem doesn't see the packets, so it doesn't create a mroute table entry. If I send out packets with TTL=2 briefly, then switch to TTL=1 packets, they are filtered correctly until the mroute entry expires. My question: is there some trick to getting the switch to filter the TTL=1 packets, or am I out of luck? Below are the relevant parts of the config, with a representative VLAN interface. I can provide more info as needed. #show run ... ip routing ip multicast-routing distributed no ip igmp snooping report-suppression ! interface Vlan44 ip address 172.23.44.1 255.255.255.0 no ip proxy-arp ip pim passive ... #show ip igmp snooping vlan 44 Global IGMP Snooping configuration: ------------------------------------------- IGMP snooping : Enabled IGMPv3 snooping (minimal) : Enabled Report suppression : Disabled TCN solicit query : Disabled TCN flood query count : 2 Robustness variable : 2 Last member query count : 2 Last member query interval : 1000 Vlan 44: -------- IGMP snooping : Enabled IGMPv2 immediate leave : Disabled Multicast router learning mode : pim-dvmrp CGMP interoperability mode : IGMP_ONLY Robustness variable : 2 Last member query count : 2 Last member query interval : 1000

  Read the article

• Server 2003 R2 - II6- granting access to website via IP with subnet range

  - by John

  We are trying to allow for a client to connect to our website. By default we are Denying all access except for those with the specified IPs we have configured to run, everything before has just been a single IP address. However now we must implement a range of IPs and rather than input thousands of records we want to use the group of computer options in the Grant Access page. However we have it configured to work off of the IP 72.21.192.0 with a subnet mask of 255.255.224.0 They are unable to connect. Looking over our IIS logs they are receiving a 302 error which is the same behavior anyone should get whom is unauthorized to view the page in question. The IP address coming in is 72.21.217.2, so it should be well within the rage of acceptable IP addresses. I'm at a loss as everything I look up tells me to do what we are doing. So any insight would be appreciated. Especially because I'm a software guy not hardware. Thanks!

  Read the article

• Setting up virtualbox for outside access

  - by Morgan Green

  I have a computer running a server that my subdomain on my shared hosting account points to. IE subdomain.mydomain.org goes to my home server. Now then; what I'm wanting to do is be able to access my VirtualBox servers through that subdomain and a different port. E.G Ubuntu Virtual Box Server 1 Username:Ubuntuhost1 Password:MyUbuntuHost1 Port:4000 Internal IP: 192.168.1.60 External IP: 24.29.138.45 Ubuntu Virtual Box Server 2 Username:UbuntuHost2 Password:MyUbuntuHost2 Port:4001 Internal IP: 192.168.1.61 External IP: 24.29.138.45 Now I want to be able to access RDP number 1 through Port 4000, but if I access Port 4001 it will connect to the server on port 4001; both using the same subdomain. The next issue is the fact that even though I know what the IP addresses are on the router for the virtualbox hosts through ifconfig it doesn't change the fact that they don't show up on the router. If anyone knows how to configure this to work please help me out because I've been racking my brain to the highest extent I can. Alright; here's an edit to clarify more; Sorry. My ports on the router are edited to forward Port 4000 on Internal IP 192.168.1.63 (My Ubuntu Internal IP address) Now when I go to my Router Home Page my VirtualBox Internal IP Address doesn't show on the attached device listings, so I set up port forwarding anyways to the VirtualBox Internal IP. My end goal is when I connect to mydomain.org and I connect through port 3389 it takes me to my host computers server, but if I put in mydomain.org and go through port 4000 it's going to redirect to my VirtualBox server; Is this even possible? Sorry; I'm trying to clarify the most I think I can I just don't know how else to explain my issue.

  Read the article

• How to set static ip address on vmware for NAT guest vms from an ubuntu Host dhcp server?

  - by javadba

  I need to configure various linux flavor NAT'ed guest vm's to have static ip addresses provided by the Ubuntu host. The vmware documentation punts on this topic, deferring to "see the man pages for your linux distribution". But the generic pages for "my linux distro" do not know about the special stuff for vmware e.g. vmnet8. Pointers from someone who just knows how to do this would be much appreciated. Here is the /etc/vmware/vmnet8/dhcpd/dhcpd.conf: allow unknown-clients; default-lease-time 1800; # default is 30 minutes max-lease-time 7200; # default is 2 hours subnet 192.168.238.0 netmask 255.255.255.0 { range 192.168.238.128 192.168.238.254; option broadcast-address 192.168.238.255; option domain-name-servers 192.168.238.2; option domain-name localdomain; default-lease-time 1800; # default is 30 minutes max-lease-time 7200; # default is 2 hours option netbios-name-servers 192.168.238.2; option routers 192.168.238.2; } host vmnet8 { hardware ethernet 00:50:56:C0:00:08; fixed-address 192.168.238.1; option domain-name-servers 0.0.0.0; option domain-name ""; option routers 0.0.0.0; } Fromt the dhcpd.conf documentation, we are supposed to add an entry for static hosts similar to the following: host mystatichostonee { hardware ethernet 00:20:6B:C7:9B:E4; fixed-address 192.168.238.101; } host mystatichosttwo { hardware ethernet 00:23:7a:C7:9c:F2; fixed-address 192.168.238.102; } But notice that the vmnet8 entry in the vmware-generated dhcpd.conf already is set to fixed-address. I don't know how to add the specifics for my hosts to that vmnet8 entry: do they become nested?

  Read the article

• How to include worksheet 3 and 4 in a cell formula provided?

  - by user21255

  I have been kindly given this formula with an explanation on how it works: Insert this formula into the cell B4 of the sheet "Cases": =IF(NOT(ISBLANK('1st'!B25)),'1st'!B25,IF(NOT(ISBLANK(INDIRECT("'2nd'!R" & (ROW($B4)-(COUNTA('1st'!$B:$B)-COUNTA('1st'!$B$1:$B$24))-4+25) & "C" & COLUMN(B4),FALSE))),INDIRECT("'2nd'!R" & (ROW($B4)-(COUNTA('1st'!$B:$B)-COUNTA('1st'!$B$1:$B$24))-4+25) & "C" & COLUMN(B4),FALSE),"")) Copy the formula to the other cells in the worksheet; the relative addresses will adjust automatically. The formula works like this: Check if there is content in 1st. If yes, copy it. If no, find out how many entries there are in 1st in total. (This is done by using the COUNTA function on the whole B column in 1st and subtracting the number of non-empty cells above the actual case data.) Use this information together with the current cells's number to find out the location of the cell that has to be copied from 2nd. Create the address of the cell and use the ISBLANK function on the INDIRECT function with that address to check if the cell is empty. If it is not, use the INDIRECT function again to display it. If it is empty, just display an empty string. Now this works fine when I have only 2 sheets. But lets say I want to include a third and fourth sheet (name as 3rd and 4th respectively), then what and should I put the formula for this in the formula above? There are actually 31 sheets but if I know how to add 3rd and 4th sheet in the formula, then I can figure out how to do the rest. Thanks

  Read the article

• connecting to server with multiple nics in other vlan

  - by Thierry

  I have a windows 2003 server with 3 nics on 3 vlan's (this is in domain 1). nic 1 has a default gateway to my router/firewall (sonicwall). In nic 2 and 3 I have left it empty, because it is advised like that everywhere. Within this domain and VLAN's 1-3 everything works fine. BUT... I have a second domain (domain 2) with a 4th Vlan (all 4 VLAN's connected to the same router/firewall) from which my clients need to access the 2003 server in domain 1 (it's my antivirus management console for both domains). when i ping the server from my vlan4 by it's FQDN, it randomly chooses ip from nic 1, 2 or 3 from my 2003 server. (logically because that server is know in DNS with it's 3 IP-addresses. And that is needed for my VLAN's 1-3) I don't really have a problem with that. BUT, I only get an answer of NIC1 (which sounds logically to me, because it's the only one with a gateway). It is not a router problem, because I'm testing in this phase and ping from vlan4 to any machine in vlan1, 2 or 3 that has 1 nic works just fine. If i add a gateway to nic2 and nic3, I get answer from all 3 nics and this works fine. But I know it's adviced to not do that. Can anyone give me advice in this particular case? Would it really be a problem to add a gateway to nic 2 and 3? They would be pointing to the same router/firewall (only with different ip-address, based on the vlan). Or is there another good solution to fix this problem? Thank's in advance, Thierry.

  Read the article

• Does MySQL have some kind of DoS protection or per-user query limit?

  - by Ghostrider

  I'm a bit at a loss. I'm running a MySQL database that's roughly 1GB data in indices combined on a dedicated Linux server. DB version is '5.0.89-community'. Configuration is controlled via cPanel. PHP actually runs elsewhere on a shared hosting. IP addresses are static and don't change. Access from remote IP address is properly configured. Website gets around 10K hits per day with each hit generating a a database query. Some of these queries are expensive (~1 sec execution time). All is fine and well until at some point DB server starts refusing connections from the client, claiming that specific user can't access the server from that IP. Resetting the server will always fix the problem for a day or two and then the same thing happens. There are some other DBs on that server, some of which are hit pretty hard on occasion but constantnly. One of the apps maintains several persistent connections since it does couple of updates per minute. Though I don't think it's related. What's driving me mad is that I can't figure out why server would start refusing connections. There is nothing in the logs. This server is a hosted dedicated server so hosting company created the OS image and I didn't write or go over every line of configuration. I'd do it but I'm at a loss as to where start looking. Any advice is appreciated.

  Read the article

• Configuring network route between two routers on home network

  - by Paul

  I have a home network - the main router connected to the internet (and has wifi) is a Netopia box. Connected to it is a Linksys router. Everything currently works - I can connect via the wireless network and get to the internet. Machines connected to the Linksys can connect with each other and connect to the internet. Both routers are configured to serve addresses via DHCP (Netopia 192.168.1.1 - 192.168.1.99), Linksys (192.168.0.1 - 192.168.0.100). Here's how they are connected: Internet <-> Netopia w/wifi (192.168.1.254) <-> Linksys (192.168.0.1) I decided I really need to allow wireless connections to also communicate with machines behind the Linksys router. Currently the Linksys is configured to obtain an IP address via DHCP. I thought this would be straightforward. I configured the Linksys to have a static IP address: IP: 192.168.1.100 Mask: 255.255.255.0 GW: 192.168.1.254 Then I configured a static route on the Netopia: Network: 192.168.0.0 Mask: 255.255.255.0 GW: 192.168.1.100 So it should now look like this: Internet <-> Netopia w/wifi (192.168.1.254) <-> (192.168.1.100) Linksys (192.168.0.1) I reset both routers. I cannot ping the Netopia (192.168.1.254) from inside the Linksys network, and if I attempt to ping 192.168.0.1 from a wifi connection I get a "Destination host not available" error. Obviously I'm missing something, but I'm not sure where. Any ideas on what I'm missing?

  Read the article

• IP6 seems to be enabled - How do I configure it without interfering with IP4?

  - by Mister IT Guru

  I noticed that some of my Centos boxes have IP6 enabled, and seem to have addresses. I have no problem with this, but I would like to get a handle on it, and even connect to them using IP6. This would really help if for any reason DHCP has a hiccup. But I'm a bit lost as to where the configuration on my CentOS box is. (I am also on google researching this, but I like server fault! :) ) I am hoping that I would be able to log into this via the VPN because every now and then that DHCP device has a bad morning, and needs to be restarted. (I'm also looking into this issue, but someone else handles that, management separation gone mad!) It's a remote client, so it would be a lot easier for me to connect to these systems which seem to self configure, to use that as a pivot via ssh tunnels to get to other remote devices to continue to manage them, while out main route is fixed. I guess, my questions are How can I configure IP6 without interfering with IP4, and On CentOS, can I influence this auto configuration I seem to be seeing?

  Read the article

• WOL doesn't work if set to anything other than `a` but this setting makes it boot all the time

  - by Elton Carvalho

  I manage a small "cluster" of 4 Xeon machines with Intel boards in my lab. They are all plugged to a 5-port 3-Com switch with static IP addresses like 10.0.0.x. They are all running OpenSuse 11.4 and their /home/ is served by one of the machines (node00) via NFS. They are plugged to an UPS that can keep them on for ca. 15 minutes, but there are lots of electric shortages due to "unscheduled maintenace" that are longer than this. So they end up being powered down without notice. If I set the BIOS to turn them on after power shortages, the issue is that they all boot at the same time and, if node00 decides to run fsck in the /home/ partition, it does not finish booting before the others try to NFS mount their /home/. I am trying to make wake on lan work, so I can choose to boot the NFS clients only after the server has successfully booted. The problem is that when I run ethtool I get an output like this: Supports Wake-on: pumbag Wake-on: g Theoretically, it is set to wake on MagicPacket(tm), according to the manual. But sending the WOL packet using wol -i 10.0.0.255 $MACADDR does not wake up the box after I shut it down with halt. The ethernet link led blinks after I send the packet, so it appears to be getting to the machine. However, if I set it up with ethtool -s eth1 wol bag, the machine always wakes up right after halting, even if I don't send the Magic packet. This means that the device can wake up with LAN activity, but seems to be ignoring the magic packet. Setting wol ag does not wake the box with the MagicPacket. Does setting wol a mean that it should boot with any broadcast message? How can I diagnose the issue of the machine not waking up with the MagicPacket even though I am sending it and it's set up to wake up with it? Thanks in advance!

  Read the article

• What's going on with traceroute?

  - by Kevin

  The following is what happens when I run traceroute from a certain location: # traceroute google.com traceroute to google.com (74.125.227.39), 30 hops max, 60 byte packets 1 gateway.local.enactpc.com (10.0.0.1) 0.138 ms 0.101 ms 0.084 ms 2 * * * 3 * * * 4 * * * 5 * * * 6 * * * 7 * * * 8 * * * 9 * * * 10 * * * 11 * * * 12 * * * 13 * * * 14 * * * 15 * * * 16 * * * 17 * * * 18 * * * 19 * * * 20 * * * 21 * * * 22 * * * 23 * * * 24 * * * 25 * * * 26 * * * 27 * * * 28 * * * 29 * * * 30 * * * Absolutely nothing of interest... Now, originally I thought this was just a fact of the location's network set up. (I assume they block pings or something...) However, watch what happens when I use nmap to run a traceroute... # nmap -sP --traceroute google.com Starting Nmap 5.21 ( http://nmap.org ) at 2012-09-25 22:18 CDT Nmap scan report for google.com (74.125.227.40) Host is up (0.034s latency). Hostname google.com resolves to 11 IPs. Only scanned 74.125.227.40 rDNS record for 74.125.227.40: dfw06s06-in-f8.1e100.net TRACEROUTE (using proto 1/icmp) HOP RTT ADDRESS 1 0.19 ms gateway.local.enactpc.com (10.0.0.1) 2 1.93 ms 99-20-92-1.lightspeed.austtx.sbcglobal.net (99.20.92.1) 3 25.61 ms 99-20-92-2.lightspeed.austtx.sbcglobal.net (99.20.92.2) 4 ... 6 7 23.68 ms 12.83.68.137 8 31.30 ms gar23.dlstx.ip.att.net (12.122.85.73) 9 ... 10 31.82 ms 72.14.233.65 11 32.27 ms 209.85.250.77 12 32.98 ms dfw06s06-in-f8.1e100.net (74.125.227.40) Nmap done: 1 IP address (1 host up) scanned in 3.29 seconds When using nmap I get A LOT more results than with traceroute, why? Note, I checked, and the difference in target IP addresses is not related...

  Read the article

• Has anyone had luck running 802.1x over ethernet using the stock Windows or other free supplicant?

  - by maxxpower

  I just wanted to see if anyone else has had luck implementing 802.1x over ethernet. So here's my basic setup. Switch sends out 3 eapol messages spaced out 5 seconds apart. if there's no response the machine gets put on a guest vlan with restricted access. If the machine is properly configured it will authenticate and be placed into a secure vlan. About 10% of my windows xp users are getting self assigned 169 addresses. I've used the Odyssey Access Client and it worked without a hitch. I'm using the setting to automatically use the users windows login to authenticate, but it's workign on 90% of the machines so I don't think that's the issue. Checking the logs on the dc it seems that the machines are trying to authenticate with computer credentials even though they are configured not to. I'm running Juniper switches with IAS for radius. I have radius configured for PEAP and MSvhapv2. Macs and linux boxes seem to have no issues authenticating. One last thing to add If I unplugging the ethernet cable and plug it back in usually resolves the issue, but I'd hardly call that acceptable for production. Kinda long winded and specific for a discussion, but just want to see if anyone else has had similar issues or experiences, or if anyone knows of a free XP supplicant that actually works with 802.1x over ethernet.

  Read the article

• Windows Server 2008 R2 Virtual Network Setup

  - by jpearl01

  Some background: I'm very much new to networking in general, and virtualization in particular. I'm trying to set up a series of VMs as we are transitioning to a thin client setup. I have been supplied a limited number of static ip addresses. The server is located in an offsite building which houses the network we use to connect to the internet, share folders etc. The setup I've been trying to go for is this: The host OS (Windows Server 2008 R2) is bound to one nic using one of the static ips (say, Nic1 and ip 10.255.6.61). I've set up another external virtual network attached to another physical nic , and a virtual private network attached to no nic. There is one VM running the same os (as the host). This VM is connected to both the external virtual network (and uses another static ip say Nic2 and ip 10.255.6.62) and also to the virtual private network (I gave it a static random ip 192.168.88.1 subnet mask 255.255.255.0). This virtual private network is connected to all the other VMs. I'd like to share the internet connection with all the other VMs on the private virtual network, and so I installed the RRAS role on the server connected to Nic2, and selected the option to share the internet over the vpn. I've run through the RRAS wizard a few times, trying different configurations, but none of them seem to be letting the other vms connect to the 'net. The vms seem to connect to the virtual private network fine, they are assigned an ip address and everything, but no internet, and no rest of the network either. The other problem is in general I connect to the vms with RDP. Will that be possible with a setup like this? i.e. will the vms show up as computers on the network? If not, what are my other options? Thanks! ~josh

  Read the article

• Tracking IP through a socks5 proxy + RDP ?

  - by piro

  Hi all. We were having some issues at work until we found that we are being attacked almost every day. The attacker seems pretty smart - at first he was always using proxy to hide his IP. With scanning I found that they were socks 5 proxy. The last week we had 11 attacks and every time i found the ip i scanned it with nmap. I found that ALL of the 11 different ip addresses were RDP (port 3389 open, and accept rdp connections, checked by myself on ALL of them). So here follow the questions: 1. Can we trace his real IP back through a socks5 proxy ? 2. Can we trace him if he is using some RDP server to hide his ip ? Please do not answer like "Call the owner of the proxy server/RDP..." etc. we already tried it and it didn't work, that's why I am writing here. Thank you very much.

  Read the article

• Two hosts on same subnet can't see each other

  - by Joey Hewitt

  I've got two routers with two separate public IP addresses on the same subnet, but I can't get them to talk to each other. Both are connected to the internet (ISP-provided gateway) via Ethernet ports provided by the landlord, but I don't have access to or knowledge of how those are physically connected or the protocols used to get back to the ISP. I can ping either from the outside, but they can't ping each other. Traceroutes in and out look the same, and they receive the same gateway over DHCP. I can ping other IPs on the subnet, so I assume this is not any sort of intentional isolation for security/privacy. Since I'm in a setup where my landlord provides internet and we don't have contact with the ISP, I can't really ask the ISP for help (doubt the landlord would know much either.) The situation is similar to the diagram at this question, but instead of the two servers, there's another router coming off the (presumed) switch, and I don't have access to the switch. I've tried giving them static routes to each other with the ISP internet gateway as the gateway, but that's not working. One is a Linksys WRT54GL running DD-WRT, the other is a Netgear WGR614v7, although I could get something more capable if necessary. I'd like to keep them each connected directly to the ISP on their WAN ports, but I can have an ethernet cable between them if necessary - I'm wondering if there's a way without that, and if there isn't, I'd appreciate advice on how to get that working. Sorry this is so nitpicky; there are reasons for all the constraints, but they don't apply to the real question, so I left them out. ;) Thank you!

  Read the article

• Configure static IPv6 on Ubuntu

  - by Charles Offenbacher

  I'm trying to configure IPv6 on a dedicated Ubuntu server. My provider gave me a "/64" (whatever that is - I'm still confused) of IPv6 addresses. However, when I try to use them, I can't ping anything. What do I do? :( # ping6 ipv6.google.com PING ipv6.google.com(vx-in-x63.1e100.net) 56 data bytes From fe80::219:d1ff:fefb:42d8 icmp_seq=1 Destination unreachable: Address unreachable From fe80::219:d1ff:fefb:42d8 icmp_seq=2 Destination unreachable: Address unreachable From fe80::219:d1ff:fefb:42d8 icmp_seq=3 Destination unreachable: Address unreachable --- ipv6.google.com ping statistics --- 3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 2014ms # tracepath6 ipv6.google.com 1?: [LOCALHOST] 0.025ms pmtu 1500 1: fe80::219:d1ff:fefb:42d8%eth0 2000.022ms !H Resume: pmtu 1500 # cat /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 64.***.***.*** netmask 255.255.255.248 gateway 64.***.***.*** iface eth0 inet6 static pre-up modprobe ipv6 address 2607:F878:1:***::1 netmask 64 gateway 2607:F878:1:***(same as address)::1 # ifconfig eth0 Link encap:Ethernet HWaddr 00:19:d1:fb:42:d8 inet addr:64.***.***.*** Bcast:64.***.***.*** Mask:255.255.255.248 inet6 addr: fe80::219:d1ff:fefb:42d8/64 Scope:Link inet6 addr: 2607:f878:1:***::1/64 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:52451 errors:0 dropped:0 overruns:0 frame:0 TX packets:39729 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6817761 (6.8 MB) TX bytes:6153835 (6.1 MB) Interrupt:41 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:166 errors:0 dropped:0 overruns:0 frame:0 TX packets:166 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:31714 (31.7 KB) TX bytes:31714 (31.7 KB)

  Read the article

• Network structure --> Server 2k8r2 <--> Livebox <--> Router <--> Other PCs

  - by Yusuf

  I have a Livebox connection to the Internet and I have set up my network as follows: - Livebox <--> Win2k8R2 Server - Livebox <--> Netgear N150 Router - Router <--> Other PCs Therefore, in my LAN, - the Livebox has IP address 192.168.1.1, - the Router 192.168.1.12 (when accessed from the Livebox or the server), - the Router 10.0.0.1 (when accessed from the PCs connected to the Router), - the server 192.168.1.2, - the PCs 10.0.0.x I was using a previous configuration, which was as follows: - Livebox <--> Netgear N150 Router - Router <--> Win2k8R2 Server - Router <--> Other PCs Everything was simple, and I just had to forward all ports for incoming connection on the Livebox to the Router, and then forward the specific ports to the Server as needed (it must be however noted that any server I use is found on the Win2k8R2 server itself). In this previous configuration, the IP addresses were as follows: - Livebox 192.168.1.1 - Router 192.168.1.12 (when seen from Livebox) - Router 10.0.0.1 (when seen from server & PCs connected to it) - Server 10.0.0.2 - PCs 10.0.0.x So now of course, my port-forwarding does not work anymore since the server is not connected (directly) to the Router. What I would like to know is how do I configure the Livebox and Router to still have the features like before? From what I understand of networks (which is very limited, btw), I see these options: Make the router assign IPs like 192.168.1.x (but then I want the forwarding to be done from the router itself, is it possible?) The forwarding on the router to the server uses IP address 10.0.0.2. I could change it to 192.168.1.2 (Is that even possible, does it work?) Forward all ports from the Livebox itself to the server, and then manage them there (Is software-based port-forwarding as secure as hardware-based?)

  Read the article

• Connecting to unsecured wireless network

  - by Sanchez

  I would like to know what information is public and can be intercepted in a non-open, but unsecured wireless network. Moreover, is there anything I can do to make it more "secure", other than using https connection whenever possible. In more details, I recently discovered (with surprise) that the wireless network in my school is actually unsecured. Although not everyone can connect to it (you need a student ID), I am told that certain softwares like Wireshark would be able to intercept the data. Since I have been using the network for all private purposes (email, facebook etc), I do feel quite insecure now and would like to understand the situation a bit better. I installed Wireshark and tried to play with it but all I can see are something alien to me. In any case, all I see seems to come directly/indirectly from my IP address, and I have long thought that usually different computers in the same wireless network would be assigned different addresses. Am I wrong? If not, then I feel very confused about what information is actually being captured (potentially by other users in the network, since I don't think I could capture activities of others in the same network anyway), and whether it's safe to use the network at all. (Gambling on others in the same network showing good behaviour is apparently not an option.) Thank you.

  Read the article

• I go to www.facebook.com, but a completely different site appears.

  - by Rosarch

  I am going to www.facebook.com, but the site that appears is totally different. This occurs on Chrome 6+, IE9, and FF 3+. What could be happening? Is this a security risk? Facebook was working just fine, then all of a sudden this happened. Update: The same problem occurs on my netbook. Update 2: When I go to http://69.63.189.11/, it works fine. So... DNS problem? How do I fix? Update 3: Checked the hosts file: # Copyright (c) 1993-2009 Microsoft Corp. # # This is a sample HOSTS file used by Microsoft TCP/IP for Windows. # # This file contains the mappings of IP addresses to host names. Each # entry should be kept on an individual line. The IP address should # be placed in the first column followed by the corresponding host name. # The IP address and the host name should be separated by at least one # space. # # Additionally, comments (such as these) may be inserted on individual # lines or following the machine name denoted by a '#' symbol. # # For example: # # 102.54.94.97 rhino.acme.com # source server # 38.25.63.10 x.acme.com # x client host # localhost name resolution is handled within DNS itself. # 127.0.0.1 localhost # ::1 localhost Looks like it hasn't been altered.

  Read the article

• Cisco RV042 VPN with Dynamic IPs - Remote Gateway Not Resolving

  - by Rister

  I have an existing network setup that I inherited from my predecessor. Currently there are two sites, each with a Linksys RV042 VPN router running the 1.3.12.19-tm firmware. They are currently set up with a Gateway to Gateway VPN. One site has a static IP, the other has a Dynamic IP with a hostname set up on no-ip.com. My company is looking to set up another site so I purchased another RV042 only this one was Cisco branded and it is running the latest firmware. I had assumed that I would be able to configure a vpn from our main office (the dynamic ip) to the new site with this router quite easily. However when I set up a new VPN tunnel on either device, it stays on Waiting for Connection and the Remote Gateway shows an ip address of 0.0.0.0 rather than the remote ip address. The other VPN tunnel is still working and I don't see any obvious misconfiguration on the new router. It seems that the router is not resolving the Dynamic DNS address and therefore not giving me the option to connect the VPN. Does a Gateway to Gateway VPN work with Dynamic IP addresses on each end? Are the firmware versions not compatible? Is there something I've missed?

  Read the article

• How to limit reverse SSH tunelling ports?

  - by funktku

  We have a public server which accepts SSH connections from multiple clients behind firewalls. Each of these clients create a Reverse SSH tunnel by using the ssh -R command from their web servers at port 80 to our public server. The destination port(at the client side) of the Reverse SSH Tunnel is 80 and the source port(at public server side) depends on the user. We are planning on maintaining a map of port addresses for each user. For example, client A would tunnel their web server at port 80 to our port 8000; client B from 80 to 8001; client C from 80 to 8002. Client A: ssh -R 8000:internal.webserver:80 clienta@publicserver Client B: ssh -R 8001:internal.webserver:80 clientb@publicserver Client C: ssh -R 8002:internal.webserver:80 clientc@publicserver Basically, what we are trying to do is bind each user with a port and not allow them to tunnel to any other ports. If we were using the forward tunneling feature of SSH with ssh -L, we could permit which port to be tunneled by using the permitopen=host:port configuration. However, there is no equivalent for reverse SSH tunnel. Is there a way of restricting reverse tunneling ports per user?

  Read the article

• Undeliverable e-mail message from [email protected]

  - by QGfisher

  I am responsible for IT for a small charity and we have a problem with a few individuals who e-mail us on our hosted e-mail addresses. The individual is on btconnect and our server is also on BT broadband and using MSExchange. I understand that the message from [email protected] are generated by Exchange but can't tell whether this is a problem with our server (seems unlikely as most people send and receive e-mails perfectly well) or with the sender's server. I have copied a sample test message below and would be very grateful if somebody can explain what is causing this problem. I have * the personal details - hope that's acceptable but I don't want to compromise the individual's identity/security. ----- Original Message ----- From: "System Administrator" To: "****" <****.***@btconnect.com Sent: Tuesday, April 06, 2010 3:26 PM Subject: Undeliverable: Test Message Your message To: ***** Subject: Test Message Sent: Tue, 6 Apr 2010 15:25:59 +0100 did not reach the following recipient(s): ***@quiltersguild.org.uk on Tue, 6 Apr 2010 15:26:07 +0100 The e-mail account does not exist at the organization this message was sent to. Check the e-mail address, or contact the recipient directly to find out the correct address.

  Read the article

• Migrating to AWS Cloud with auto-scaling - where to put Redis and ElasticSearch?

  - by RobMasters

  I've been trying to research this topic but haven't found anywhere that recommends where to install services such as Redis and ElasticSearch when migrating to a cloud framework. I'm currently running a Symfony2 application on 2 static servers - one is running MySQL and the other is the public facing web server, which also has Redis and ElasticSearch running on it. Both of these servers are virtualised, but they're static in terms of not being able to replicate at present (various aspects are still dependent on the local filesystem). The goal is to migrate to AWS and use auto-scaling to be able to spin up and kill web servers as required, but I'm not clear on what I should put on each EC2 instance. Should they be single-responsibility only? i.e. Set up individual instances for the web server(s), Redis, and ElasticSearch and most likely an RDS instance for MySQL and only set up auto-scaling on the web server(s)? I don't foresee having to scale the ElasticSearch server anytime soon as it's only driving the search functionality, but it's possible that Redis may need to be replicated at some point - but should this be done manually? I'm not sure of how this could be done automatically as each instance needs to be configured to know about it's master/slave(s) as far as I know. I'd appreciate advice on this. One more quick question while I'm here - how would I be able to deploy code changes when there are X web servers currently active? I'm using a Capifony deployment script (Symfony2 version of Capistrano), which I think can handle multiple servers easily enough by specifying an array of :domain addresses...but how can should this be handled when the number of web servers can vary?

  Read the article

< Previous Page | 409 410 411 412 413 414 415 416 417 418 419 420  | Next Page >