Search Results

Search found 66435 results on 2658 pages for 'system volume information'.

Page 424/2658 | < Previous Page | 420 421 422 423 424 425 426 427 428 429 430 431  | Next Page >

• GA 8KNXP Rev1.0: 4GB installed, only 3.5 recognized by BIOS

  - by hurikhan77

  I've installed 2x 1 GB and 4x 512 MB memory into my GA-8KNXP system which would sum up to 4GB. The specs from the manual say: Maximum memory support: 4GB. If all six slots are utilized, slot 5+6 may only equipped with single-sided RAM modules. And so I did. Anyway: The BIOS counts up to 3.5 GB and finishes there. Also my linux system reports only 3.5 GB of memory although 4 GB memory support is activated in the kernel. So I suppose this is a memory mapping issue or a hardware issue. I've tried removing only on of the 512 MB memory modules leaving 5 modules in place. But that just stopped the system from powering on correctly (screen stays black although fans and leds come to live). Dual Channel was detected and enabled so the system technically found all 6 modules. "dmidecode" in linux reports only memory in slots 1 to 4 and ignores slots 5+6, so it only detects 3 GB of memory. It also says the system would support up to 16 GB of memory with 4 GB modules per slot. I think technically the chipset should be able to offer and utilize the complete 4 GB memory range. Any clues what else I could check? Or do I have just to live with 0.5 GB wasted memory?

  Read the article

• How should I use LVM with Ganeti?

  - by javano

  I am building a small Ganeti cluster on some low end hardware (I only have the resources given sadly). I am confused as to the use of LVMs with DRBD. I have two instances and three nodes. What I want is instance1 replicated between node 1 & 2, and instance2 replicated between nodes 3 & 2 (so node2 is doing nothing, except waiting for either node1 or 3 to fail, is it is the secondary node for both instances). This is because node2 is a lower hardware spec than 1 and 3, so I just want it as an hot-spare. How can I achieve this? I don't want instance1 being replicated to node3 for example, nor instance2 replicated to node1. Nodes 1 & 2 have /dev/sda5 which is 150GBs (for example). Nodes 2 & 3 have /dev/sda6 which is also 75GBs (for example). Using just nodes 1 & 2, after looking at the Ganeti docs I would; vgcreate my-vg Next I would create the cluster via gnt-cluster VG = "my-vg". It is here I believe that I am missing some knowledge. I believe that what I need to do is create the same Logical Volume on nodes 1 & 2 in Volume Group "my-vg", that solely consists of /dev/sda5 and call it "lv1". Then create an Logical Volume on nodes 2 & 3 the solely consists of /dev/sda6 in "my-vg" that is called "lv2". When creating instance1 I would then use "-vg=lv1 -n node1:node2", and when creating instance2 I would use "-vg=lv2 -n node3:node2". I breifly had a go at this today and I'm dubious if this will be possible. When trying to create instance2, "lv2" wont exist on node1 (the cluster master) so I don't believe it will allow the instance creation. Could I create a 1kb parition (/dev/sda6) on node1 and put it into a LV called "lv2" or is that too flakey? Is this set up possible? Thank you.

  Read the article

• How to mount remote samba share from local host with multiple groups?

  - by Dragos

  I am using mount.cifs to mount a remote samba share (both client and server are Ubuntu server 8.04) like this: mount.cifs //sambaserver/samba /mountpath -o credentials=/path/.credentials,uid=someuser,gid=1000 $ cat .credentials username=user password=password I mounted a user from local system with username and password with mount.cifs but the problem is that the user is part of multiple groups on the remote system and with mount.cifs I can only specify one gid. Is there a way to specify all the gids that the remote user has? Is there a way to: Mount the remote samba with multiple groups on the local system? Browse the mount from 1) with the terminal since I want to pass some files from samba as arguments to local programs. Other solutions would be: nautilus sftp:// which runs through gvfs; but the newer gnome does not write to disk the ~/.gvfs anymore so I can't browse it in terminal. And the last solution would be NFS but that means that I have to synchronize the uids and gids on the local system with the ones from the server.

  Read the article

• Time issues on the Network -- How to find the Root Cause

  - by Jeff

  A number of application servers started erroring out in my domain. Troubleshooting led me to a missconfiguration of NTP. I fixed the issue, but I don't know how the issue arose in the first place. The only errors I can find are System Error: 1097 Source: useenv System Error: 1058 Source: useenv System Error: 1030 Source: useenv System Error: 1000 Source: mmc How else can I find out why NTP started acting up on my domain? Is there any troubleshooting steps to diagnose why my DC started pulling from a random timeserver with the wrong time? EDIT: Current issue actually remains: the two 2003 DCs are not syncing with the PDC (a 2k8 box). w32tm /resync -- The computer did not resync because no time data was available.

  Read the article

• Remote desktop in XP?

  - by vineth

  hi, I have enabled remote desktop in my xp sp3 system, (My problem) if my friend take my system in remote with out my authentication my system is connected to him.but few day before i get authentication message(attached in the below link) but nowadays i am not receiving this dialog box... please provide help to get this authentication dialog box.. Link : http://www.freeimagehosting.net/image.php?f9f04c5e0a.jpg Thanks in advance

  Read the article

• Window 7 Host does not answer to ping

  - by gencha

  Today I tried printing on a shared printer on one of our homegroup members. Sadly it did not work (printer marked as offline). Shortly after, I noticed I can't even ping the machine that owns the printer (I also can not remotely access it in any other way I've tried). Currently I'm trying to ping the machine from the router both computers are connected to (and my machine in question doesn't answer). I do receive the echo requests (as verified with WireShark). I also added a rule in the Windows Firewall to specifically allow ICMP echo requests, but that didn't change anything. I also tried netsh firewall set icmpsetting 8 enable, but that didn't change anything either. Completely disabling the Windows Firewall has no effect on the issue either. One has to wonder, where does Windows log when and why it ignored any incoming packets? How can I get to the bottom of this? Here are some ways I found to dig deeper into the issue: Enabling logging on the Windows Firewall Enabling Windows Filtering Platform Auditing Both methods at least give more insight into the issue. The plain log file is full of entries like this: 2011-11-11 14:35:27 DROP ICMP 192.168.133.1 192.168.133.128 - - 84 - - - - 8 0 - RECEIVE So the ICMP packets are being dropped as if that was intended. The Event Viewer now gives a little bit more details: The Windows Filtering Platform has blocked a packet. Application Information: Process ID: 4 Application Name: System Network Information: Direction: Inbound Source Address: 192.168.133.1 Source Port: 0 Destination Address: 192.168.133.128 Destination Port: 8 Protocol: 1 Filter Information: Filter Run-Time ID: 214517 Layer Name: Receive/Accept Layer Run-Time ID: 44 This same entry is always repeated with 2 points of information changing: Process ID: 420 Application Name: \device\harddiskvolume2\windows\system32\svchost.exe The service host with the PID 420 is the host for the following services: Windows Audio DHCP Client Windows Event Log HomeGroup Provider TCP/IP NetBIOS Helper Security Center Additionally, there is currently this problem with the same machine: Even though my network is set to be a "Home network", I am unable to create a new homegroup.

  Read the article

• Xen HVM guest has severe clock drift

  - by ipartola

  I am seeing a very severe clock drift on my Xen HVM VPS, rented from a hosting provider, so I don't have access to the dom0 system. I continuously run ntpd, but the clock drifts by as much as 30 seconds in 5 minutes and NTP cannot keep up. Has anyone experienced this? Here are some details: $ dmesg | grep clock [ 0.160000] Measured 347 cycles TSC warp between CPUs, turning off TSC clock. [ 0.396000] * this clock source is slow. Consider trying other clock sources [ 0.550448] Switching to clocksource acpi_pm [ 0.653135] rtc_cmos 00:05: setting system clock to 2011-03-09 02:45:40 UTC (1299638740) $ cat /sys/devices/system/clocksource/clocksource0/available_clocksource acpi_pm $ cat /sys/devices/system/clocksource/clocksource0/current_clocksource acpi_pm

  Read the article

• Webcam microphone input in Gnome/pulseaudio

  - by sdaau

  Just got a "Trust" webcam, which gets recognized on my Ubuntu Lucid. It has a built in microphone - which also gets recognized - however, I cannot really get it to act as the system microphone input? Here are some screenshots of what is shown by gnome-volume-control: The default window shows Trust webcam - which has two profiles: "Analog Mono Input" and "Off" - of course, I have it on "Analog Mono Input": However, on the "Input" tab - there is no matching "device for sound input" - neither a matching connector: Then I installed pavucontrol - but that doesn't show that much more; it tells first that gnome-volume-control reads from "Internal Audio Analog Stereo": Then in "Input devices" tab, there is again nothing resembling the mic input from webcam: Finally, under "Configuration" tab, the "Trust" webcam shows, but even if its profile is on "Analog Mono Input", nothing much happens:   So, does anyone know how I could get this webcam microphone to be recognized as the system input? Many thanks in advance for any answers, Cheers!

  Read the article

• SQL Server plus small files

  - by user1467163

  I have a MSSQL server, 3 volumes, that runs some processes that seem to take way too long. One of these processes reads in a zip file, then writes to a database based on what's in the zip file.... for each record. I have 2 volumes in use and am creating the third- so I am trying to plan how to do this. OS has to remain on vol. 1. The TLogs should probably go on the new volume and the mdf's on the existing vol.2.. Do I put the file store on the volume with the MDF's so they don't interfere with the TLog writes, or with the TLogs so they don't interfere with the TLog flush to the MDFs? I know it's best to have more servers / volumes but I have to make do with whats on hand for now. I appreciate any suggestions.

  Read the article

• Create kickstart configuration file from existing configuration.

  - by ÜMineiro

  Is there a script or another way to automatically generate a kickstart configuration file from the system state of an existing server so that the file can be use to replicate (not clone) the configuration of the system in another install? I know that the anaconda-ks.cfg file is stored on the /root dir. but the system in question have been extensively changed since it's installation, and the file is of no use now.

  Read the article

• Can a folder on a NAS be made available as a physical drive in VMWare?

  - by asbjornu

  We are currently in the process of moving from a single web server to two load balanced web servers and are facing some challenges we don't quite know how to fix. One of these is that the current single server hosts applications that write stuff to disk. The applications running on the server expects that when something is written to disk it later will in fact exist, so it's important that this premise is fulfilled with the dual server architecture as well. The dual server setup is a couple of VMWare instances with Windows Server 2008 R2 as the guest operating system. Out of the box, these instances does not share any kind of file system, so just moving the applications over would make them break since one instance would write something to the file system that doesn't exist on the other. Thus we need to share a file system between the two virtual servers. Our host has proposed to create a network share on a SAN and map this share individually on each virtual machine. This doesn't work too well due to NTFS permissions, etc., because the share needs to be accessed by several independent web applications that won't even be in the same application pool. The only solution that kind of works is to hard code an "identity" for each web application into its web.config file, but this means password in clear text which doesn't sit well with me. Since the servers are virtual, I'm thinknig: Wouldn't it be possible to make a NAS area available as a physical disk in the gues operating system somehow? Since VMWare has full control of the virtual hardware, you'd think it would be able to "fake" a local hard drive in the virtual machine that in reality is a folder on a NAS, but so far I haven't found anything that states how and if this is possible. So I have to ask the wonderful Server Fault community: Can a folder on a NAS be made available as a physical drive (typical D:) in both of the virtual machines?

  Read the article

• Video registry

  - by Vik Gamov

  Looking for some video content management system for setting up video registry in my company

  Read the article

• How can visiting a webpage infect your computer?

  - by Cybis

  My mother's computer recently became infected with some sort of rootkit. It began when she received an email from a close friend asking her to check out some sort of webpage. I never saw it, but my mother said it was just a blog of some sort, nothing interesting. A few days later, my mother signed in on the PayPal homepage. PayPal gave some sort of security notice which stated that to prevent fraud, they needed some additional personal information. Among some of the more normal information (name, address, etc.), they asked for her SSN and bank PIN! She refused to submit that information and complained to PayPal that they shouldn't ask for it. PayPal said they would never ask for such information and that it wasn't their webpage. There was no such "security notice" when she logged in from a different computer, only from hers. It wasn't a phishing attempt or redirection of some sort, IE clearly showed an SSL connection to https://www.paypal.com/ She remembered that strange email and asked her friend about it - the friend never sent it! Obviously, something on her computer was intercepting the PayPal homepage and that email was the only other strange thing to happen recently. She entrusted me to fix everything. I nuked the computer from orbit since it was the only way to be sure (i.e., reformatted her hard drive and did a clean install). That seemed to work fine. But that got me wondering... my mother didn't download and run anything. There were no weird ActiveX controls running (she's not computer illiterate and knows not to install them), and she only uses webmail (i.e., no Outlook vulnerability). When I think webpages, I think content presentation - JavaScript, HTML, and maybe some Flash. How could that possibly install and execute arbitrary software on your computer? It seems kinda weird/stupid that such vulnerabilities exist.

  Read the article

• NetBackup's bplist doesn't get user/group info for Windows files

  - by Gnustavo

  I'm trying to get information about storage consumption from NetBackup's bplist output. I'm running NBU 6.0MP5 on a RHEL 3 server. The server is backing up several Solaris, Linux, and Windows machines. When I use bplist to get information about files backed up on any UNIX machine I get something like this: # bplist -C unixclient -R 99 -l -s 01/28/2006 -e 01/29/2006 / drwxr-xr-x test ccase 0 Nov 16 09:28 /l/home2/test/ -rw------- test ccase 4737 Jan 06 17:54 /l/home2/test/.bash_history -rw-rw-r-- test ccase 104 Nov 11 2004 /l/home2/test/.bashrc However, when I use it to list files backed up on any Windows client I can't get the user and group information. They both always appear as 'root'. Like this: # bplist -C winclient -t 13 -R 99 -l -s 02/20/2006 / drwx------ root root 0 Feb 20 14:26 /C/temp/ -rwx------ root root 41 Feb 20 14:26 /C/temp/asdf.txt drwx------ root root 0 May 25 2004 /C/temp/CTRMNGR/ Does anyone know why bplist doesn't show the correct user/group for Windows files? If it can't, is there a way to get that information using another command? Thanks. Gustavo.

  Read the article

• How can visiting a webpage infect your computer?

  - by Cybis

  My mother's computer recently became infected with some sort of rootkit. It began when she received an email from a close friend asking her to check out some sort of webpage. I never saw it, but my mother said it was just a blog of some sort, nothing interesting. A few days later, my mother signed in on the PayPal homepage. PayPal gave some sort of security notice which stated that to prevent fraud, they needed some additional personal information. Among some of the more normal information (name, address, etc.), they asked for her SSN and bank PIN! She refused to submit that information and complained to PayPal that they shouldn't ask for it. PayPal said they would never ask for such information and that it wasn't their webpage. There was no such "security notice" when she logged in from a different computer, only from hers. It wasn't a phishing attempt or redirection of some sort, IE clearly showed an SSL connection to https://www.paypal.com/ She remembered that strange email and asked her friend about it - the friend never sent it! Obviously, something on her computer was intercepting the PayPal homepage and that email was the only other strange thing to happen recently. She entrusted me to fix everything. I nuked the computer from orbit since it was the only way to be sure (i.e., reformatted her hard drive and did a clean install). That seemed to work fine. But that got me wondering... my mother didn't download and run anything. There were no weird ActiveX controls running (she's not computer illiterate and knows not to install them), and she only uses webmail (i.e., no Outlook vulnerability). When I think webpages, I think content presentation - JavaScript, HTML, and maybe some Flash. How could that possibly install and execute arbitrary software on your computer? It seems kinda weird/stupid that such vulnerabilities exist.

  Read the article

• ldirectord ipvsadm not show reals ip and not work wtih pacemaker and corosync

  - by miguer27

  first thanks for your time. I'm having a problem with ldirectord that I can not solve, I comment my situation: I have two nodes with pace maker and corosync and configure somes resources: root@ldap1:/home/mamartin# crm status Last updated: Tue Jun 3 12:58:30 2014 Last change: Tue Jun 3 12:23:47 2014 via cibadmin on ldap1 Stack: openais Current DC: ldap2 - partition with quorum Version: 1.1.7-ee0730e13d124c3d58f00016c3376a1de5323cff 2 Nodes configured, 2 expected votes 7 Resources configured. Online: [ ldap1 ldap2 ] Resource Group: IPV_LVS IPV_4 (ocf::heartbeat:IPaddr2): Started ldap1 IPV_6 (ocf::heartbeat:IPv6addr): Started ldap1 lvs (ocf::heartbeat:ldirectord): Started ldap1 Clone Set: clon_IPV_lo [IPV_lo] Started: [ ldap2 ] Stopped: [ IPV_lo:1 ] root@ldap1:/home/mamartin# crm configure show node ldap2 \ attributes standby="off" node ldap1 \ attributes standby="off" primitive IPV-lo_4 ocf:heartbeat:IPaddr \ params ip="192.168.1.10" cidr_netmask="32" nic="lo" \ op monitor interval="5s" primitive IPV-lo_6 ocf:heartbeat:IPv6addrLO \ params ipv6addr="[fc00:1::3]" cidr_netmask="64" \ op monitor interval="5s" primitive IPV_4 ocf:heartbeat:IPaddr2 \ params ip="192.168.1.10" nic="eth0" cidr_netmask="25" lvs_support="true" \ op monitor interval="5s" primitive IPV_6 ocf:heartbeat:IPv6addr \ params ipv6addr="[fc00:1::3]" nic="eth0" cidr_netmask="64" \ op monitor interval="5s" primitive lvs ocf:heartbeat:ldirectord \ params configfile="/etc/ldirectord.cf" \ op monitor interval="20" timeout="10" \ meta target-role="Started" group IPV_LVS IPV_4 IPV_6 lvs group IPV_lo IPV-lo_6 IPV-lo_4 clone clon_IPV_lo IPV_lo \ meta interleave="true" target-role="Started" location cli-prefer-IPV_LVS IPV_LVS \ rule $id="cli-prefer-rule-IPV_LVS" inf: #uname eq ldap1 colocation LVS_no_IPV_lo -inf: clon_IPV_lo IPV_LVS property $id="cib-bootstrap-options" \ dc-version="1.1.7-ee0730e13d124c3d58f00016c3376a1de5323cff" \ cluster-infrastructure="openais" \ expected-quorum-votes="2" \ no-quorum-policy="ignore" \ stonith-enabled="false" \ last-lrm-refresh="1401264327" rsc_defaults $id="rsc-options" \ resource-stickiness="1000" The problem is in the ipvsadm only show a one real IP, when i configured two now, show the ldirector.cf: root@ldap1:/home/mamartin# ipvsadm IP Virtual Server version 1.2.1 (size=4096) Prot LocalAddress:Port Scheduler Flags - RemoteAddress:Port Forward Weight ActiveConn InActConn TCP ldap-maqueta.cica.es:ldap wrr - ldap2.cica.es:ldap Route 4 0 0 TCP [[fc00:1::3]]:ldap wrr - [[fc00:1::2]]:ldap Route 4 0 0 root@ldap1:/home/mamartin# cat /etc/ldirectord.cf checktimeout=10 checkinterval=2 autoreload=yes logfile="/var/log/ldirectord.log" quiescent=yes #ipv4 virtual=192.168.1.10:389 real=192.168.1.11:389 gate 4 real=192.168.1.12:389 gate 4 scheduler=wrr protocol=tcp checktype=on #ipv6 virtual6=[[fc00:1::3]]:389 real6=[[fc00:1::1]]:389 gate 4 real6=[[fc00:1::2]]:389 gate 4 scheduler=wrr protocol=tcp checkport=389 checktype=on and in the logs I see nothing clear: root@ldap1:/home/mamartin# ldirectord -d /etc/ldirectord.cf start DEBUG2: Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.11:389 -g -w 0) Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.11:389 -g -w 0) DEBUG2: Quiescent real server: 192.168.1.11:389 (192.168.1.10:389) (Weight set to 0) Quiescent real server: 192.168.1.11:389 (192.168.1.10:389) (Weight set to 0) DEBUG2: Disabled real server=on:tcp:192.168.1.11:389:::4:gate:\/: (virtual=tcp:192.168.1.10:389) DEBUG2: Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.12:389 -g -w 0) Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.12:389 -g -w 0) DEBUG2: Quiescent real server: 192.168.1.12:389 (192.168.1.10:389) (Weight set to 0) Quiescent real server: 192.168.1.12:389 (192.168.1.10:389) (Weight set to 0) DEBUG2: Disabled real server=on:tcp:192.168.1.12:389:::4:gate:\/: (virtual=tcp:192.168.1.10:389) DEBUG2: Checking on: Real servers are added without any checks DEBUG2: Resetting soft failure count: 192.168.1.12:389 (tcp:192.168.1.10:389) Resetting soft failure count: 192.168.1.12:389 (tcp:192.168.1.10:389) DEBUG2: Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.12:389 -g -w 4) Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.12:389 -g -w 4) Destination already exists root@ldap1:/home/mamartin# cat /var/log/ldirectord.log [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Quiescent real server: 192.168.1.11:389 (192.168.1.10:389) (Weight set to 0) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Quiescent real server: 192.168.1.12:389 (192.168.1.10:389) (Weight set to 0) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Resetting soft failure count: 192.168.1.12:389 (tcp:192.168.1.10:389) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.12:389 -g -w 4) failed: [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Added real server: 192.168.1.12:389 (192.168.1.10:389) (Weight set to 4) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Resetting soft failure count: 192.168.1.11:389 (tcp:192.168.1.10:389) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Restored real server: 192.168.1.11:389 (192.168.1.10:389) (Weight set to 4) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Resetting soft failure count: [[fc00:1::2]]:389 (tcp:[[fc00:1::3]]:389) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] system(/sbin/ipvsadm -a -t [[fc00:1::3]]:389 -r [[fc00:1::2]]:389 -g -w 4) failed: [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Added real server: [[fc00:1::2]]:389 ([[fc00:1::3]]:389) (Weight set to 4) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Resetting soft failure count: [[fc00:1::1]]:389 (tcp:[[fc00:1::3]]:389) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Restored real server: [[fc00:1::1]]:389 ([[fc00:1::3]]:389) (Weight set to 4) do not know if this is a bug or a configuration error, can anyone help? Regards.

  Read the article

• Windows 7 ignores F6/F8 and will not boot

  - by P.Brian.Mackey

  I have a work PC with sophos safeguard encryption on it. Windows failed to start. When I bootup I receive an error saying a recent hardware or software change might be the cause. File: \Boot\BCD Status: 0xc0000098 Info: The windows boot configuration data file does not contain a valid OS entry. This began after the PC forced me to run a system recovery. My machine had powered down improperly (power outage?) and simply would not respond to my keyboard input to cancel the option to scan my system. After the scan "repaired" a boot file, my system crashed. Now it tells me I can insert my windows 7 disk and run recovery. I can't simply do this because of Safeguard. The system recovery can't see my encrypted drive. I tried hitting F2 to manually login to Safeguard and then selected the option to boot from media. The computer prompts me to hit any key to boot from disk...which I do, but once again it is not reading my keyboard input. I can't get F8/F6 to bypass startup files and get me to a command prompt like the old days. If I could get to a command prompt I might could recover the file windows jacked up from its backup location...though I may need to use the windows recovery disk UI to do this..??? In the past I've been able to slap in a PS/2 keyboard when the USB keyboards stop responding like this. I have no PS/2 keyboard available. Anyone have any idea how I can undo the damage windows system recovery has done with safeguard installed?

  Read the article

• MPlayer refuses to generate mono wav file

  - by JCCyC

  I want to downsample an existing audio file to 8KHz mono. This command line downsamples it to stereo: mplayer -quiet -vo null -vc dummy -af volume=0,resample=8000:0:1 -ao pcm:waveheader:file="/tmp/blah1.wav" ~/from_my_cellphone.3ga It generates a file that the file utility identifies as stereo: $ file /tmp/blah1.wav /tmp/blah1.wav: RIFF (little-endian) data, WAVE audio, Microsoft PCM, 16 bit, stereo 8000 Hz Now, if I read the documentation correctly, I should add pan=1:0.5:0.5 so I get a file that's half the size: mplayer -quiet -vo null -vc dummy -af volume=0,resample=8000:0:1:pan=1:0.5:0.5 -ao pcm:waveheader:file="/tmp/blah2.wav" ~/from_my_cellphone.3ga But it doesn't! blah2.wav is identical to blah1.wav! What am I doing wrong?

  Read the article

• Allowing non-admin users to unstick the print spooler

  - by Reafidy

  I currently have an issue where the print que is getting stuck on a central print server (windows server 2008). Using the "Clear all documents" function does not clear it and gets stuck too. I need non-admin users to be able to clear the print cue from there work stations. I have tried using the following winforms program which I created and allows a user to stop the print spooler, delete printer files in the "C:\Windows\System32\spool\PRINTERS folder" and then start the print spooler but this functionality requires the program to be runs as an administrator, how can I allow my normal users to execute this program without giving them admin privileges? Or is there another way I can allow normal user to clear the print que on the server? Imports System.ServiceProcess Public Class Form1 Private Sub Button1_Click(sender As System.Object, e As System.EventArgs) Handles Button1.Click ClearJammedPrinter() End Sub Public Sub ClearJammedPrinter() Dim tspTimeOut As TimeSpan = New TimeSpan(0, 0, 5) Dim controllerStatus As ServiceControllerStatus = ServiceController1.Status Try If ServiceController1.Status <> ServiceProcess.ServiceControllerStatus.Stopped Then ServiceController1.Stop() End If Try ServiceController1.WaitForStatus(ServiceProcess.ServiceControllerStatus.Stopped, tspTimeOut) Catch Throw New Exception("The controller could not be stopped") End Try Dim strSpoolerFolder As String = "C:\Windows\System32\spool\PRINTERS" Dim s As String For Each s In System.IO.Directory.GetFiles(strSpoolerFolder) System.IO.File.Delete(s) Next s Catch ex As Exception MsgBox(ex.Message) Finally Try Select Case controllerStatus Case ServiceControllerStatus.Running If ServiceController1.Status <> ServiceControllerStatus.Running Then ServiceController1.Start() Case ServiceControllerStatus.Stopped If ServiceController1.Status <> ServiceControllerStatus.Stopped Then ServiceController1.Stop() End Select ServiceController1.WaitForStatus(controllerStatus, tspTimeOut) Catch MsgBox(String.Format("{0}{1}", "The print spooler service could not be returned to its original setting and is currently: ", ServiceController1.Status)) End Try End Try End Sub End Class

  Read the article

• GRUB2 UEFI booting from LVM on RAID (with XEN)

  - by pavian

  I'm experimenting with booting root fs from LVM volume inside the raid (mdraid superblock 1.x) via UEFI with GRUB2. Also I'm using Xen hypervisor. From grub command line I can see my lvm volume (ls command) but I got kernel panic due to "unable to mount root fs". I saw a note in this article telling it's probably impossible to boot root fs from raid via UEFI, but I don't understand the reason why not. Is it possible to boot linux with this configuration without the initramfs (which I don't won't to use)?

  Read the article

• Deleting large no of files on linux eats up CPU

  - by Sanjay

  I generate more than 50GB of cache files on my RHEL server (and typical file size is 200kb so no of files is huge). When I try to delete these files it takes 8-10 hours. However, the bigger issue is that the system load goes to critical for these 8-10 hours. Is there anyway where I can keep the system load under control during the deletion. I tried using nice -n19 rm -rf * but that doesn't help in system load.

  Read the article

• How to interpret IOZone results?

  - by homer5439

  Here are the resuts of running IOZone on an ext3 filesystem on an LVM volume residing on a SAN LUN (it was ran with 5 parallel processes). "Throughput report Y-axis is type of test X-axis is number of processes" "Record size = 4 Kbytes " "Output is in Kbytes/sec" " Initial write " 81628.55 " Rewrite " 83354.72 " Read " 115595.02 " Re-read " 119306.09 " Reverse Read " 47684.20 " Stride read " 10011.09 " Random read " 16751.27 " Mixed workload " 5659.77 " Random write " 1661.85 " Pwrite " 36030.83 Now this is all nice and dandy, but my question is: how do I know whether the values are as good as they could be or there is something to tweak (and if so, what?) The actual usage I will have for that Logical Volume is to act as virtual disk for a VM.

  Read the article

• How to mount remote sambe from local host with multiple groups ?

  - by Dragos

  I am using mount.cifs to mount a remote samba share (both client and server are Ubuntu server 8.04) like this: mount.cifs //sambaserver/samba /mountpath -o credentials=/path/.credentials,uid=someuser,gid=1000 `$ cat .credentials username=user password=password I mounted a user from local system with username and password with mount.cifs but the problem is that the user is part of multiple groups on the remote system and with mount.cifs I can only specify one gid. Is there a way to specify all the gids that the remote user has ? Is there a way to: 1) Mount the remote samba with multiple groups on the local system ? 2) Browse the mount from 1) with the terminal since I want to pass some files from samba as arguments to local programs. Other solutions would be: nautilus sftp:// which runs through gvfs but the newer gnome does not write to disk the ~/.gvfs anymore so I can't browse it in terminal. An the last solution would be nfs but that means that I have to synchronize the uids and gids on the local system with the ones from the server.

  Read the article

• Why do disk images hosted on a read-only HFS+ partition behave differently?

  - by deceze

  I have come across the following phenomenon and would like to know how leaky Windows' file system abstraction is or if there's something else involved. I partitioned the hard disk of my MacBook Pro and installed Windows 7 (64 bit). The Boot Camp driver package includes file system drivers that enable Windows to access the Mac OS HFS+ partition. It's read-only access, but it works. Now, I have some disk images of stuff I usually install, so I grabbed a copy of Daemon Tools to mount them. When I mount an image saved on the HFS+ partition, about two out of three installers on these disks (usually InstallShield) crash with all sorts of weird errors. Most are just gibberish that lead to all sorts of non-solutions on Google, one was "This application is not the right type for your computer, check if you need 32 or 64 bit versions." When moving the image files to another Windows 7 computer on the network and mounting them from the network share, they work fine. My question now is, why do applications behave differently depending on whether the read-only image file, which should be abstracted away through the read-only virtual Daemon Tools drive, is located on a read-only HFS+ partition or on a Windows network share? And I'll just roll this into the question as well since I was wondering: Does the file system of a network share matter? Does the client system need to understand the file system of the share host or is that abstracted away in SMB?

  Read the article

• Should use EXT4 or XFS to be able to 'sync'/backup to S3?

  - by Rafa

  It's my first message here, so bear with me... (I have already checked quite a few of the "Related Questions" suggested by the editor) Here's the setup, a brand new dedicated server (8GB RAM, some 140+ GB disk, Raid 1 via HW controller, 15000 RPM) it's a production web server (with MySQL in it, too, not just serving web requests); not a personal desktop computer or similar. Ubuntu Server 64bit 10.04 LTS We have an Amazon EC2+EBS setup with the EBS volume formatted as XFS for easily taking snapshots to S3, via AWS' console. We are now migrating to the dedicated server and I want to be able to backup our data to Amazon's S3. The main reason being the possibility of using the latest snapshot from an EC2 instance in case of hardware failure on the dedicated server. There are two approaches I am thinking of: do a "simple" file-based backup with rsync, dumping the database' and other files, and uploading to amazon via S3 API commands, or to an EC2 instance, or something. do a file-system "freeze" (using XFS) with the usual ebs/ec2 snapshot tool to take part of the file system, take a snapshot, and upload it to Amazon. Here's my question (or series of questions): Can I safely use XFS for the whole system as the main and only format on the dedicated server? If not, is it safe to use EXT4? Or should I use something else? would then be possible to make snapshots of the system to upload to Amazon? Is it possible/feasible/practical to do what I want to do, anyway? any recommendations? When searching around for S3/EBS/XFS, anything relevant to my problem is usually focused on taking snapshots of a XFS system that is already an EBS volume. My intention is to do it in a "real"/metal dedicated server. Update: I just saw this on Wikipedia: XFS does not provide direct support for snapshots, as it expects the snapshot process to be implemented by the volume manager. I had always assumed that I could choose 2 ways of doing snapshots: via LVM or via XFS (without LVM). After reading this, I realize these 2 options are more like it: With XFS: 1) do xfs_freeze; 2) copy the frozen files via, eg, rsync; 3) unfreeze xfs With LVM and XFS: 1) do xfs_freeze; 2) make a binary copy of the frozen fs via lvcreate and related commands; 3) unfreeze xfs; 4) somehow backup the LVM snapshot. Thanks a lot in advance, Let me know if I need to clarify something.

  Read the article

< Previous Page | 420 421 422 423 424 425 426 427 428 429 430 431  | Next Page >