Search Results

Search found 12375 results on 495 pages for 'red black tree'.

Page 437/495 | < Previous Page | 433 434 435 436 437 438 439 440 441 442 443 444  | Next Page >

• Laptop LCD sometimes stops working on reboot. Please help.

  - by J Ringle

  I have a Gateway P-6831FX Laptop with Vista Ultimate. The Laptop LCD will sometimes not come on after I reboot the computer. I don't even close the lid and it happens. It isn't dim, it doesn't come on at all. No posting of CMOS (BIOS), nothing. Please note... this happens sometimes, not every time. Frustrating! When plugged into an external monitor, which works fine, Vista display properties can't even "sense" the laptop LCD. I try to enable the laptop LCD for dual display, turning on the laptop LCD, and it does nothing. It's like the laptop LCD is not even there. Manually taking a magnet in my hand to the laptop lid sensing switch (the sensor that turns off display/sleep mode when you close lid), sometimes causes the LCD backlight to "turn on" but not display any images. By "turn on" I mean I can see the screen backlight turn on to a 'dark gray' screen instead of pitch black. Subsequent reboot the laptop display is not working again! Here are the facts: Only happens at random and only after a reboot. Waking from Sleep mode isn't a problem. Pressing F4 function key for dual display does nothing when this happens. Closing lid doesn't seem to be related. (unless it is only after reboot.) using external magnet from laptop screen sensor sometimes triggers backlight to turn on but reboot back to square one with no LCD display. an external display always works fine. I have taken apart LCD, checked all wires and ribbons for loose connections or damage. I have replaced the Inverter. It doesn't seem to be heat related as I can put in sleep mode and resume fine when very hot. (external monitor works fine too). Sometimes the screen works fine as if there is not a problem at all. Even after a reboot... This is random. Any ideas out there? If it is a bad part... which one? The LCD seems to be fine. What are the odds of 2 bad inverters? The backlight is fine. The LCD wires/ribbons seem to be fine. I am at a loss. No warranty left and Gateway tech support is clueless. Thanks for any feedback that might help.

  Read the article

• Cannot install g++ on ubuntu

  - by Erel Segal

  I don't have g++: erelsgl@ubuntu:/etc/apt$ which g++ erelsgl@ubuntu:/etc/apt$ erelsgl@ubuntu:/etc/apt$ g++ The program 'g++' can be found in the following packages: * g++ * pentium-builder Try: sudo apt-get install <selected package> So I try to install it: erelsgl@ubuntu:~/srilm$ sudo apt-get install g++ Reading package lists... Done Building dependency tree Reading state information... Done g++ is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 5 not upgraded. 2 not fully installed or removed. After this operation, 0B of additional disk space will be used. Setting up g++ (4:4.4.3-1ubuntu1) ... update-alternatives: error: alternative path /usr/bin/g++ doesn't exist. dpkg: error processing g++ (--configure): subprocess installed post-installation script returned error exit status 2 dpkg: dependency problems prevent configuration of build-essential: build-essential depends on g++ (>= 4:4.3.1); however: Package g++ is not configured yet. dpkg: error processing build-essential (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. Errors were encountered while processing: g++ build-essential E: Sub-process /usr/bin/dpkg returned an error code (1) I also try to install build-essential, and get same results. I also tried "sudo apt-get update" - didn't help. This is my apt-cache: erelsgl@ubuntu:/etc/apt$ apt-cache policy g++ build-essential g++: Installed: 4:4.4.3-1ubuntu1 Candidate: 4:4.4.3-1ubuntu1 Version table: *** 4:4.4.3-1ubuntu1 0 500 http://il.archive.ubuntu.com/ubuntu/ lucid/main Packages 100 /var/lib/dpkg/status build-essential: Installed: 11.4build1 Candidate: 11.4build1 Version table: *** 11.4build1 0 500 http://il.archive.ubuntu.com/ubuntu/ lucid/main Packages 100 /var/lib/dpkg/status erelsgl@ubuntu:/etc/apt$ I also tried this and got the same error: erelsgl@ubuntu:~/Ace/Files/corpus$ sudo dpkg --configure -a Setting up g++ (4:4.4.3-1ubuntu1) ... update-alternatives: error: alternative path /usr/bin/g++ doesn't exist. dpkg: error processing g++ (--configure): subprocess installed post-installation script returned error exit status 2 dpkg: dependency problems prevent configuration of build-essential: build-essential depends on g++ (>= 4:4.3.1); however: Package g++ is not configured yet. dpkg: error processing build-essential (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: g++ build-essential

  Read the article

• GRUB 2 freezing at OS selection screen, what could be the cause?

  - by Michael Kjörling

  Mains power is somewhat unreliable where I live, so every now and then, the computer gets rebooted when the PSU can't maintain proper voltage during a brown-out or momentary black-out. It's happened a few times recently that when power is restored, the BIOS POST completes successfully, GRUB starts to load and then freezes. I've seen this at the Welcome to GRUB! message, but it seems to happen more often just past the switch to the graphical OS list. At this point, the computer will not respond to anything (arrow keys, control commands, Ctrl+Alt+Del, ...) - it simply sits there displaying this image, seemingly doing nothing more. At that point, turning the computer off using the power button and letting it sit for a while (cooling down?) has allowed it to boot successfully. Turning the computer off and immediately back on seems to give the same result (successful POST then freeze in GRUB). This behavior began recently, although does not seem to be directly correlated with my hard disk woes (although it may be relevant that GRUB resides on that physical disk, I don't know). Once the computer has booted, it runs without a hitch. I know that a "proper" solution would be to invest in a UPS, but what might be causing behavior like this? I was thinking in terms of perhaps the CPU shutting down as a thermal control measure, but if that was the cause then wouldn't I see similar freezes during use (which I do not)? What else could cause freezes apparently closely but not perfectly related to the BIOS handover from POST to OS bootloader? The BIOS settings are to reset to previous power status after a power loss. Since the PC in question is almost always turned on, this means restore to full power status. I have no expansion cards installed that make any BIOS extensions known by screen output during the boot process, at least, but I do have a few expansion cards installed. Haven't made any changes in that regard in a long time, now. I haven't touched GRUB itself for a long time, whether configuration or binaries, so I don't think that's the problem. Also, it doesn't really make sense that a bug in GRUB would manifest itself only once in a blue moon but significantly more often after a power failure.

  Read the article

• Blank Screen After Login on Windows 7

  - by Leigh Riffel

  When unlocking a Windows 7 computer the screen briefly (less than a second) goes blank before showing the screen. Abound once a month (but sometimes within a few days) when I unlock my computer the screen doesn't come back from this brief blackout and stays black. Sometimes after five minutes or so the display will come back. Other times it has been blank for over 20 minutes, so I give up and restart the computer. It seems to happen more often when the computer has been locked for a longer period of time - I lock my computer several times a day, but the problem most happens when I come in at the start of the day. I have updated my video card and monitor drivers. I have two monitors driven by the same graphics card. The computer is a Dell Optiplex 740. When the problem occurs both monitors have a green light on to indicate that they are receiving signal. I've tried unplugging the monitors from the video card and turning the monitors on and off. The screen saver is set to one that is not blank screen. The Windows power settings are set to never turn off the display. When the problem occurs there is no significant disk activity occurring. When the problem occurs I can connect over the network to the hard drive on my computer. When the problem occurs I can't connect over the network with a VNC connection. The VNC client doesn't give an error, but also won't show the screen. The task actually seems to hang as I can see the task, but there is no window for it. This problem occurred when I was running a pre-release version of Windows 7. The hard drive was formatted for release version and the problem still occurs. I've been stopping some of my always running programs to see if one of them may be the culprit, but given the span between failures that will take some time to find the problem if it will even help at all. Some programs I have always running include IE, Firefox, Outlook, Evernote, Kana Reminder, Ditto, Macro Express, Timesnapper, and DisplayFusion. Any ideas appreciated.

  Read the article

• How can I install things in Linux with *no yum* and *no wget*?

  - by e9t

  I'm a newbie to Linux (that mainly uses Windows and Mac OS X) needing some advice. I was trying to install git on a Linux machine today, and encountered some problems: Not knowing the version of the installed OS, I've opened the /proc/version file which said: Linux version 2.6.9-42.0.2.ELsmp ([email protected]) (gcc version 3.4.6 20060404 (Red Hat 3.4.6-3)) #1 SMP Thu Aug 17 17:57:31 EDT 2006 Then, as written in the git documents (http://git-scm.com/download/linux), I assumed I could use the yum install git command for Fedora, but got the following result. [root@myserver ~]# yum install git -bash: yum: command not found So I tried installing yum using wget, but wasn't so lucky. [root@myserver ~]# wget http://linux.duke.edu/projects/yum/download/2.0/yum-2.0.7.tar.gz -bash: wget: command not found I googled and found this page and this page, so tried installing yum with rpm, but only got a result full of question marks. (Possibly an encoding problem, hmm...) [root@myserver ~]# rpm -Uvh http://www.eomy.net/linux/install-yum-x86_64/wget-1.10.2-0.40E.x86_64.rpm http://www.eomy.net/linux/install-yum-x86_64/wget-1.10.2-0.40E.x86_64.rpm(??)?? ?????? ?: /var/tmp/rpm-xfer.TbuAOu: V3 DSA signature: NOKEY, key ID 443e1821 ???.. ########################################### [100%] wget-1.10.2-0.40E U???????g??????? wget-1.10.2-0.40E???? ??g??/usr/bin/wget ?? wget-1.10.2-0.40E U?????? ???? wget-1.10.2-0.40E???? ??g??/usr/share/man/man1/wget.1.gz ?? wget-1.10.2-0.40E U?????? ???? [root@myserver ~]# Finally, when I typed rpm --version in the terminal, I got the below results. [root@myserver ~]# rpm --version RPM ???? - 4.3.3 I would like to know what I can do or possibly try now. Is it not possible to wget or yum anything in my situation? Or is there any magical tool like homebrew (http://mxcl.github.com/homebrew/) that I can use? Any comments or advice would be appreciated. Thanks in advance!

  Read the article

• autocomplete not working on one sever, works on others

  - by dogmatic69

  I have Ubuntu 10.10 x64 and x86 running on various servers and auto complete works on all of them bar one. The issue: apt-<tab> would show a list of options but sudo apt-<tab> would not. After fiddling with it for a few hours i've found that /etc/bash_autocomplete did not exist. on the broken server. Copying the one from a working one it now works. but still not properly. sudo apt-get ins<tab> does not show do anything. listing the files in /etc/bash_autocomplete.d/ on the working server has about 50 files, and the broken one only two or three. i dont think that i can just copy these files though as it might show commands for things that are not even installed. TL;DR autocomplete broken, how can i fix it. Seems like its disabled somewhere, why is this EDIT: Ok, it was not ever installed... $ sudo apt-get install bash-completion Reading package lists... Done Building dependency tree Reading state information... Done The following NEW packages will be installed bash-completion 0 upgraded, 1 newly installed, 0 to remove and 3 not upgraded. Need to get 140kB of archives. After this operation, 1,061kB of additional disk space will be used. Get:1 http://archive.ubuntu.com/ubuntu/ maverick-updates/main bash-completion all 1:1.2-2ubuntu1.1 [140kB] Fetched 140kB in 0s (174kB/s) Selecting previously deselected package bash-completion. (Reading database ... 23808 files and directories currently installed.) Unpacking bash-completion (from .../bash-completion_1%3a1.2-2ubuntu1.1_all.deb) ... Processing triggers for man-db ... Setting up bash-completion (1:1.2-2ubuntu1.1) ... its now kinda working, but still wonky... apt-get ins<tab> gives sudo apt-get insserv as the option. also apt-get install php5<tab> gives apt-get install php5/ not php5-* options.

  Read the article

• Missing Dependency Errors when Installing OpenVas Server

  - by David

  I'm trying to install OpenVAS on Red Hat Enterprise Linux 5.5. I've successfully run yum install openvas-client, but yum install openvas-server prints the following errors: --> Finished Dependency Resolution openvas-client-3.0.1-1.el5.art.i386 from installed has depsolving problems --> Missing Dependency: libopenvas_hg.so.3 is needed by package openvas-client-3.0.1-1.el5.art.i386 (installed) openvas-client-3.0.1-1.el5.art.i386 from installed has depsolving problems --> Missing Dependency: libopenvas_nasl.so.3 is needed by package openvas-client-3.0.1-1.el5.art.i386 (installed) openvas-client-3.0.1-1.el5.art.i386 from installed has depsolving problems --> Missing Dependency: libopenvas_omp.so.3 is needed by package openvas-client-3.0.1-1.el5.art.i386 (installed) openvas-scanner-3.2-0.2.el5.art.i386 from atomic has depsolving problems --> Missing Dependency: net-snmp-utils is needed by package openvas-scanner-3.2-0.2.el5.art.i386 (atomic) openvas-client-3.0.1-1.el5.art.i386 from installed has depsolving problems --> Missing Dependency: libopenvas_misc.so.3 is needed by package openvas-client-3.0.1-1.el5.art.i386 (installed) openvas-scanner-3.2-0.2.el5.art.i386 from atomic has depsolving problems --> Missing Dependency: openldap-clients is needed by package openvas-scanner-3.2-0.2.el5.art.i386 (atomic) openvas-client-3.0.1-1.el5.art.i386 from installed has depsolving problems --> Missing Dependency: libopenvas_base.so.3 is needed by package openvas-client-3.0.1-1.el5.art.i386 (installed) Error: Missing Dependency: net-snmp-utils is needed by package openvas-scanner-3.2-0.2.el5.art.i386 (atomic) Error: Missing Dependency: libopenvas_base.so.3 is needed by package openvas-client-3.0.1-1.el5.art.i386 (installed) Error: Missing Dependency: libopenvas_hg.so.3 is needed by package openvas-client-3.0.1-1.el5.art.i386 (installed) Error: Missing Dependency: libopenvas_nasl.so.3 is needed by package openvas-client-3.0.1-1.el5.art.i386 (installed) Error: Missing Dependency: openldap-clients is needed by package openvas-scanner-3.2-0.2.el5.art.i386 (atomic) Error: Missing Dependency: libopenvas_omp.so.3 is needed by package openvas-client-3.0.1-1.el5.art.i386 (installed) Error: Missing Dependency: libopenvas_misc.so.3 is needed by package openvas-client-3.0.1-1.el5.art.i386 (installed) You could try using --skip-broken to work around the problem You could try running: package-cleanup --problems package-cleanup --dupes rpm -Va --nofiles --nodigest The program package-cleanup is found in the yum-utils package. Notice that each of the missing dependencies is followed by the words (installed) or the words (atomic) - for the name of the repository. When I try to install any of these sub-dependencies, the installation fails (either due to missing dependencies or since the rpm is already installed). For example, if I try to install a rpm for "libopenvas_hg.so.3", I get an error message indicating that it is already installed. Yet "libopenvas_hg.so.3" is listed as a missing dependency. Why? Do I need to uninstall all of the "missing" dependences first?

  Read the article

• Why is vCenter 5.1u1 exiting hosts from maintenance mode?

  - by Shane Madden

  This vCenter server was just upgraded to 5.1 update 1. I'm going through hosts and bringing firmware up to date, then upgrading them from various versions of 5.0 to 5.1u1. vCenter 5.1u1 seems to have an interesting new behavior: it's removing hosts from maintenance mode when they reconnect after being disconnected -- but very inconsistently, I've seen it maybe 4 or 5 times on ~25-30 host reboots. I've only seen it happen on 5.0 hosts that have not yet been upgraded to 5.1. In the image, I placed the host in maint mode and rebooted it into the HP SPP DVD's automatic update mode. After its usual ~40 minute update process, the host came back online.. and 7 seconds before even logging that the host had reconnected, vCenter had sent the host a task to exit maintenance mode. In my understanding, the only time vCenter should drop a host out of maintenance mode is when vCenter put it into maintenance mode itself (such as a VUM upgrade task). Why would this vCenter be unilaterally exiting a host from user-initiated maintenance mode? Edit, additional info: I ran the firmware upgrades on 5 more hosts, all at the same time. Two of them exited maint mode after reconnecting, three did not. The common factor of those exiting maint mode seems to be how long they were offline; the two that took a few tries to boot to the virtual media are the two that got knocked out of maint mode. esx31 (image above): 45 minutes unresponsive esx19 (exited maint): 87 minutes unresponsive esx24 (stayed in maint): 32 minutes unresponsive esx29 (stayed in maint): 39 minutes unresponsive esx32 (stayed in maint): 30 minutes unresponsive esx34 (exited maint): 70 minutes unresponsive Edit: The disconnect time idea seems to have been a red herring, as it's not happening consistently. Additionally, in the vpxd.log the exit maint mode task initiation seems to always immediately follow this vim.EnvironmentBrowser.queryProvisioningPolicy SOAP call. Here's the lines, slightly trimmed for clarity: 15:27:49.535 [info 'vpxdvpxdVmomi'] [ClientAdapterBase::InvokeOnSoap] Invoke done (esx31, vim.EnvironmentBrowser.queryProvisioningPolicy) 15:27:49.560 [info 'commonvpxLro'] [VpxLRO] -- BEGIN task -- esx31 -- HostSystem.exitMaintenanceMode -- Note that on the nodes that don't get the exit task, the vim.EnvironmentBrowser.queryProvisioningPolicy event still occurs. I'm not seeing any other differences in events before or after this in the reconnect process, aside from the extra events caused by exiting maintenance mode. Given the log's mention of provisioning policies, looking for autodeploy-related maintenance mode issues turns up complaints about similar behavior (though I'm not using autodeploy at all).

  Read the article

• libvirt qemu/kvm migration problem

  - by Panda

  I am using kvm and libvirt on my Dell server. Now i am trying to migrate one virtual machine from a physical server to another. However, I failed everytime. In virsh on physicalServer1, I typed: virsh # migrate virtualmachine1 qemu+ssh://username@physicalServer2/system error: operation failed: migration to 'tcp:physicalServer2:49163' failed: migration failed Then I searched FAQ part on libvirt.org. It says: error: operation failed: migration to '...' failed: migration failed This is an error often encountered when trying to migrate with QEMU/KVM. This typically happens with plain migration, when the source VM cannot connect to the destination host. You will want to make sure your hosts are properly configured for migration (see the migration section of this FAQ) I managed to ssh physicalServer2 from a shell on virtualmachine1 so the above red part did not explain my failure. I also open ports on physicalServer2, iptables -L shows following information: Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT udp -- anywhere anywhere udp dpt:bootps ACCEPT tcp -- anywhere anywhere tcp dpt:bootps ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT udp -- anywhere anywhere udp dpt:bootps ACCEPT tcp -- anywhere anywhere tcp dpt:bootps ACCEPT tcp -- anywhere anywhere state NEW tcp dpts:49152:49215 Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT) target prot opt source destination The /var/log/libvirt/qemu/virtualmachine1.log on physicalServer2: 2011-05-06 13:37:30.708: starting up LC_ALL=C PATH=/usr/local/sbin:/usr/local/bin:/usr/bin:/usr/sbin:/sbin:/bin QEMU_AUDIO_DRV=none /usr/bin/kvm -S -M pc-0.14 -enable-kvm -m 2048 -smp 1,sockets=1,cores=1,threads=1 -name openjudge-test -uuid a8c704bc-a4f9-90db-3e57-40e60b00aac1 -nodefconfig -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/virtualmachine1.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=readline -rtc base=utc -boot c -drive file=/media/nfs/virtualmachine1.img,if=none,id=drive-ide0-0-0,format=raw -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0 -drive if=none,media=cdrom,id=drive-ide0-1-0,readonly=on,format=raw -device ide-drive,bus=ide.1,unit=0,drive=drive-ide0-1-0,id=ide0-1-0 -netdev tap,fd=20,id=hostnet0 -device rtl8139,netdev=hostnet0,id=net0,mac=00:16:36:8a:22 :a0,bus=pci.0,addr=0x3 -chardev pty,id=charserial0 -device isa-serial,chardev=charserial0,id=serial0 -usb -vnc 127.0.0.1:2 -vga cirrus -incoming tcp:0.0.0.0:49163 -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x4 char device redirected to /dev/pts/0 2011-05-06 13:37:30.915: shutting down The /var/log/libvirt/qemu/virtualmachine1.log on physicalServer1 is empty. Both physical servers are using Ubuntu 11.04. The libvirt and kvm used are installed by apt-get. The libvirt version is 0.8.8.

  Read the article

• Subversion vision and roadmap

  - by gbjbaanb

  Recently C Michael Pilato of the core subversion team posted a mail to the subversion dev mailing list suggesting a vision and roadmap for the future of Subversion. Naturally, he wanted as much feedback and response as possible which is why I'm posting this here - to elicit some suggestions and contributions from you, the administrators of Subversion. Any comments are welcome, and I shall feedback a synopsis with a link to this question to the dev mailing list. Similarly, I've created a post on StackOverflow to get feedback from the programmer/user side of things too. So, without further ado: Vision The first thing on his "vision statement" is: Subversion has no future as a DVCS tool. Let's just get that out there. At least two very successful such tools exist already, and to squeeze another horse into that race would be a poor investment of energy and talent. There's no need to suggest distributed features for subversion. If you want a DVCS, there should be no ill-feeling if you migrate to Git, Mercurial or Bazaar. As he says, its pointless trying to make SVN like them when they already exist, especially when there are different usage patterns that SVN should be targetting. The vision for Subversion is: Subversion exists to be universally recognized and adopted as an open-source, centralized version control system characterized by its reliability as a safe haven for valuable data; the simplicity of its model and usage; and its ability to support the needs of a wide variety of users and projects, from individuals to large-scale enterprise operations. Roadmap Several ideas were suggested as being "very nice to have" and are offered as the starting point of a future roadmap. These are: Obliterate Shelve/Checkpoint Repository-dictated Configuration Rename Tracking Improved Merging Improved Tree Conflict Handling Enterprise Authentication Mechanisms Forward History Searching Log Message Templates Repository-dictated Configuration If anyone has suggestions to add, or comments on these, the subversion community would welcome all of them. Community And lastly, there was a call for more people to become involved with Subversion development. As with most OSS projects it can be daunting to join, but there is now a push for more to be done to help. If you feel like you can contribute, please do so.

  Read the article

• IIS6 Virtual Directory 500 Error on Remote Share

  - by David

  We have our servers at the server farm in a domain. Let's call it LIVE. Our developer computers live in a completely separate corporate domain, miles and miles away. Let's call it CORP. We have a large central storage unit (unix) that houses images and other media needed by many webservers in the server farm. The IIS application pools run as (let's say) LIVE\MediaUser and use those credentials to connect to a central storage share as a virtual directory, retrieve the images, and serve them as if they were local on each server. The problem is in development. On my development machine. I log in as CORP\MyName. My IIS 6 application pool runs as Network Service. I can't run it as a user from the LIVE domain because my machine isn't (and can not be) joined to that domain. I try to create a virtual directory, point it to the same network directory, click Connect As, uncheck the "Always use the authenticated user's credentials when validating access to the network directory" checkbox so that I can enter the login info, enter the credentails for LIVE\MediaUser, click OK, verify the password, etc. This doesn't work. I get "HTTP Error 500 - Internal server error" from IIS. The IIS log file reports sc-status = 500, sc-substatus = 16, and sc-win32-status = 1326. The documentation says this means "UNC authorization credentials are incorrect" and the Win32 status means "Logon failure: unknown user name or bad password." This would be all and good if it were anywhere close to accurate. I double- and trouble-checked it. Tried multiple known good logins. The IIS manager allows me to view the file tree in its window, it's only the browser that kicks me out. I even tried going to the virtual directory's Directory Security tab, and under Authentication and Access Control, I tried using the same LIVE domain username for the anonymous access credential. No luck. I'm not trying to run any ASP, ASP.NET, or other dynamic anything out of the virtual directory. I just want IIS to be able to load static images, css, and js files. If anyone has some bright ideas I would be most appreciative!

  Read the article

• radvd is not assigning prefix

  - by Samik

  I'm currently trying to setup IPv6 address auto-configuration with router advertisement daemon (radvd) on a virtual machine running CentOS 6.5. But the eth0 interface is not obtaining that prefix. I've obtained the ULA prefix from here. Contents of /etc/sysctl.conf # Kernel sysctl configuration file for Red Hat Linux # # For binary values, 0 is disabled, 1 is enabled. See sysctl(8) and # sysctl.conf(5) for more details. # Controls IP packet forwarding net.ipv4.ip_forward = 0 net.ipv6.conf.all.forwarding = 1 # Controls source route verification net.ipv4.conf.default.rp_filter = 1 # Do not accept source routing net.ipv4.conf.default.accept_source_route = 0 # Controls the System Request debugging functionality of the kernel kernel.sysrq = 0 # Controls whether core dumps will append the PID to the core filename. # Useful for debugging multi-threaded applications. kernel.core_uses_pid = 1 # Controls the use of TCP syncookies net.ipv4.tcp_syncookies = 1 # Disable netfilter on bridges. net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-arptables = 0 # Controls the default maxmimum size of a mesage queue kernel.msgmnb = 65536 # Controls the maximum size of a message, in bytes kernel.msgmax = 65536 # Controls the maximum shared segment size, in bytes kernel.shmmax = 68719476736 # Controls the maximum number of shared memory segments, in pages kernel.shmall = 4294967296 Contents of /etc/radvd.conf # NOTE: there is no such thing as a working "by-default" configuration file. # At least the prefix needs to be specified. Please consult the radvd.conf(5) # man page and/or /usr/share/doc/radvd-*/radvd.conf.example for help. # # interface eth0 { AdvSendAdvert on; MinRtrAdvInterval 3; MaxRtrAdvInterval 10; AdvDefaultPreference low; AdvHomeAgentFlag off; prefix fd8a:8d9d:808f:1::/64 { AdvOnLink on; AdvAutonomous on; AdvRouterAddr on; }; }; Contents of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 HWADDR=52:54:00:74:d7:46 TYPE=Ethernet UUID=af5db1cb-e809-4098-be1a-5a74dbb767b1 ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=dhcp IPV6INIT=yes IPV6_AUTOCONF=yes I've also enabled radvd at startup through chkconfig. Though I noticed that radvd is starting after interfaces are brought up. I've tried restarting the network service afterwards but still I get the following link-local address only #ip -6 addr show 1: lo: mtu 16436 inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: mtu 1500 qlen 1000 inet6 fe80::5054:ff:fe74:d746/64 scope link valid_lft forever preferred_lft forever Edit: Based on the answer given by Sander Steffann I still need clarification on some points but I'm posting here what worked. Contents of /etc/sysconfig/network NETWORKING=yes HOSTNAME=syslog-ng-server NETWORKING_IPV6=yes IPV6FORWARDING=yes Contents of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 HWADDR=52:54:00:74:d7:46 TYPE=Ethernet UUID=af5db1cb-e809-4098-be1a-5a74dbb767b1 ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=dhcp IPV6INIT=yes IPV6_AUTOCONF=yes IPV6FORWARDING=no Removed following line from /etc/sysctl.conf net.ipv6.conf.all.forwarding = 1 Contents of /etc/radvd.conf is as previous.

  Read the article

• Quantifying the effects of partition mis-alignment

  - by Matt

  I'm experiencing some significant performance issues on an NFS server. I've been reading up a bit on partition alignment, and I think I have my partitions mis-aligned. I can't find anything that tells me how to actually quantify the effects of mis-aligned partitions. Some of the general information I found suggests the performance penalty can be quite high (upwards of 60%) and others say it's negligible. What I want to do is determine if partition alignment is a factor in this server's performance problems or not; and if so, to what degree? So I'll put my info out here, and hopefully the community can confirm if my partitions are indeed mis-aligned, and if so, help me put a number to what the performance cost is. Server is a Dell R510 with dual E5620 CPUs and 8 GB RAM. There are eight 15k 2.5” 600 GB drives (Seagate ST3600057SS) configured in hardware RAID-6 with a single hot spare. RAID controller is a Dell PERC H700 w/512MB cache (Linux sees this as a LSI MegaSAS 9260). OS is CentOS 5.6, home directory partition is ext3, with options “rw,data=journal,usrquota”. I have the HW RAID configured to present two virtual disks to the OS: /dev/sda for the OS (boot, root and swap partitions), and /dev/sdb for a big NFS share: [root@lnxutil1 ~]# parted -s /dev/sda unit s print Model: DELL PERC H700 (scsi) Disk /dev/sda: 134217599s Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 63s 465884s 465822s primary ext2 boot 2 465885s 134207009s 133741125s primary lvm [root@lnxutil1 ~]# parted -s /dev/sdb unit s print Model: DELL PERC H700 (scsi) Disk /dev/sdb: 5720768639s Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 34s 5720768606s 5720768573s lvm Edit 1 Using the cfq IO scheduler (default for CentOS 5.6): # cat /sys/block/sd{a,b}/queue/scheduler noop anticipatory deadline [cfq] noop anticipatory deadline [cfq] Chunk size is the same as strip size, right? If so, then 64kB: # /opt/MegaCli -LDInfo -Lall -aALL -NoLog Adapter #0 Number of Virtual Disks: 2 Virtual Disk: 0 (target id: 0) Name:os RAID Level: Primary-6, Secondary-0, RAID Level Qualifier-3 Size:65535MB State: Optimal Stripe Size: 64kB Number Of Drives:7 Span Depth:1 Default Cache Policy: WriteBack, ReadAdaptive, Direct, No Write Cache if Bad BBU Current Cache Policy: WriteThrough, ReadAdaptive, Direct, No Write Cache if Bad BBU Access Policy: Read/Write Disk Cache Policy: Disk's Default Number of Spans: 1 Span: 0 - Number of PDs: 7 ... physical disk info removed for brevity ... Virtual Disk: 1 (target id: 1) Name:share RAID Level: Primary-6, Secondary-0, RAID Level Qualifier-3 Size:2793344MB State: Optimal Stripe Size: 64kB Number Of Drives:7 Span Depth:1 Default Cache Policy: WriteBack, ReadAdaptive, Direct, No Write Cache if Bad BBU Current Cache Policy: WriteThrough, ReadAdaptive, Direct, No Write Cache if Bad BBU Access Policy: Read/Write Disk Cache Policy: Disk's Default Number of Spans: 1 Span: 0 - Number of PDs: 7 If it's not obvious, virtual disk 0 corresponds to /dev/sda, for the OS; virtual disk 1 is /dev/sdb (the exported home directory tree).

  Read the article

• Windows 7 remains powered on when restarting

  - by BombDefused

  I'm running windows 7 x64 on an MSI P67A-GD53 motherboard, in an Antec P280 Super Midi Towercase with a Corsair 650w PSU. I've just installed a second instance of windows 7 x64 on a separate disk (this is to keep my games separate from my work OS). The problem is that it appears now that I cannot restart from either instance of Windows 7. The shut down command, and sleep commands work as expected. When I try to restart, the shutdown happens but the system never reboots. Everything remains powered on, until I hold down the power button to force the power off. Ithink (but am not 100% sure) this has only started since I installed the second OS, and am assuming this has something to do with the motherboard needing to know which OS to run up again? Some other forums I've read suggest that the PSU has a major role in restart and could be at fault. Changing the boot order of the disks in the BIOS does not change anything. Any suggestions greatfully recieved! Update: I now have a reproduceable issue: I think the secondary OS install may have been a red herring. It was when windows tried to reboot during the install that I noticed the issue. After playing around with installing drivers, and rebooting many many times, I have found that it is the OC genie setting on the MSI motherboard that seems to trigger the problem. This makes sense as I only started using the OC genie feature a couple of weeks ago, and probably hadn't used restart in that time. However... simply turning off OC genie does not make the issue go away. I have to turn off OC genie, shutdown, start enter bios, go to the "Save and Exit" menu "Restore Defaults" yes to "Load optimized defaults", which will reset to clear the problem. Now when the PC boots into windows, I can restart as normal (and from the OS on either HDD). I only know how to control the issue, and don't still know the root cause. I'd like to be able to use the OC genie function if anyone can suggest a why I'm seeing this problem. Could it be that I'm drawing too much power when using OC feature?

  Read the article

• Loose component cables causing HDMI video problems

  - by jwir3

  I'm not sure this is the correct forum, but I'll ask anyway. I have an A/V setup at home that has something like the following: Five Components (actually a few more, like a CD player, but they don't really relate to this question): Older Pioneer Receiver Digital Set Top Box Sony BluRay Player Samsung Plasma TV Speakers The reason for the receiver is so that all the sound can go through the speakers, rather than some going to the TV speakers and some to the external speakers. They are connected as follows: Digital Set Top Box connects via component video to Samsung TV directly via Component 2 (audio goes to Older Pioneer Receiver). Sony BluRay player is connected via HDMI 1 to TV, but audio goes to the receiver. Now, the problem I'm having is that when I have the digital set top box connected, there are times when the Netflix or Hulu streams I watch through the Sony BluRay player (it's connected to a router for internet access) will lose video. What I mean by this is that the sound of the episode will keep playing, but the screen will go black. If I jiggle the component cables, it will often come back. If I disconnect the component cables, it will always come back. I've noticed that one of the connections (the red component cable) doesn't like to sit very well in the component socket in the back of the digital set top box. It seems like there is a bad connection here, but it doesn't seem like this should be affecting the HDMI input at all. What I've noticed, though, is that when I disconnect the digital set top box completely (i.e. remove the component cable from the back of the TV), the problem seems to resolve itself. I'm not talking about actually removing the cable physically, because I thought perhaps the cables were mashing against one another, and possibly jiggling each other loose. To correct this possible problem, I took the component cable completely out of the cable ties it was in in the back of my entertainment center, as well as pulled the digital set top box out from the entertainment center altogether. It's now connected directly to the TV, without any other cables touching it to cause some kind of weird interference or just physical pulling on the cable. Same problem. If, however, I disconnect the component cable and just leave it sitting behind the TV, then the problem goes away. So, my question is this - what could be causing this? Is it a case where it's an improperly shielded component cable that's causing interference with the HDMI input, or something that's wrong with the TV? It's an intermittent problem, so it's difficult to track down. The TV isn't that old, so it's probably still under warranty. I'm just wondering if there is something else I can do that might reduce this problem without having to haul a massive television set out of my house to get repaired/replaced.

  Read the article

• Stack-based keyboard delay using Logitech MX3100 keyboard

  - by Mark S. Rasmussen

  I've been using a Logitech Cordless Desktop MX3100 keyboard for quite a while. I've never really had any problems, except for the occasional typo. I noticed however that I tended make the typo "Laod" instead of "Load", quite a bit more often than any other typos. As it started to get on my nerves, I decided to do some testing. What I found out was than when I write lowercase "load", I'd never make the typo. All uppercase, or just uppercase L, I'd make the typo quite often. My actual (very scientific) testing is probably best described by showing the output: moatmoatmoat MoatMoatMoat loatloatloat LaotLaotLaot loafloafloaf LaofLaofLaof hoathoathoat HoatHoatHoat hoadhoadhoad HoadHoadHoad lortlortlort LrotLrotLrot What i found out was that whenever shift was depressed, typing an uppercase "L" would induce a significant lag if the next character was an "o", compared to the lag of the any other key: High "o" lag: LoLoLoLoLoLo No "a" lag: LaLaLaLaLaLa No lag for neither "o" nor "a": lolololololo lalalalalala By realizing this I regained a slight bit of sanity as I knew I wasn't coming down with a case of Parkinsons. I was actually typing correctly, the lag just interpreted it wrongly. Now, what really bugs me is that I can't fathom how this is occurring. What I'm actually typing, in physical order, is this: L - o - a - d, and yet, the "a" is output before the "o", even though "o" was pressed before "a". So while the keyboard is processing the "Lo" combo, the "a" gets prioritized and is inserted before the "o" is done processing, resulting in Laod instead of Load. And this only happens when typing "Lo", not when typing lowercase "lo". This problem could stem from the keyboard hardware, the receiver hardware or the keyboard software driver. No matter the fault location however, I can't imagine how this could be implemented as anything but a FIFO queue. A general delay, sure, I could live with that, albeit I'd be irritated. But a lag affecting different keys differently, and even resulting in unpredictable outcome - that just doesn't make any sense. I've solved the problem by just switching to a wired keyboard. I just can't shake it off me though; what kind of bug/error/scenario would result in a case like this? Edit: It's been suggested that I stop drinking Red Bull and stick to water instead. While that may actually help solve the issue, I'm really not looking for a solution as such. I'm more interested in an explanation of how this could happen, as I can't imagine any viable technical solution that could result in this behavior.

  Read the article

• Why are emails sent from my applications being marked as spam?

  - by Brian

  Hi. I have 2 web apps running on the same server. The first is www.nimikri.com and the other is www.hourjar.com. Both apps share the same IP address (75.127.100.175). My server is through a shared hosting company. I've been testing my apps, and at first all my emails were being delivered to me just fine. Then a few days ago every email from both apps got dumped into my spam box (in gmail and google apps). So far the apps have just been sending emails to me and nobody else, so I know people aren't manually flagging them as spam. I did a reverse DNS lookup for my IP and the results I got were these: 100.127.75.in-addr.arpa NS DNS2.GNAX.NET. 100.127.75.in-addr.arpa NS DNS1.GNAX.NET. Should the reverse DNS lookup point to nimikri.com and hourjar.com, or are they set up fine the way they are? I noticed in the email header these 2 lines: Received: from nimikri.nimikri.com From: Hour Jar <[email protected]> Would the different domain names be causing gmail to think this is spam? Here is the header from one of the emails. Please let me know if any of this looks like a red flag for spam. Thanks. Delivered-To: [email protected] Received: by 10.231.157.85 with SMTP id a21cs54749ibx; Sun, 25 Apr 2010 10:03:14 -0700 (PDT) Received: by 10.151.130.18 with SMTP id h18mr3056714ybn.186.1272214992196; Sun, 25 Apr 2010 10:03:12 -0700 (PDT) Return-Path: <[email protected]> Received: from nimikri.nimikri.com ([75.127.100.175]) by mx.google.com with ESMTP id 28si4358025gxk.44.2010.04.25.10.03.11; Sun, 25 Apr 2010 10:03:11 -0700 (PDT) Received-SPF: neutral (google.com: 75.127.100.175 is neither permitted nor denied by best guess record for domain of [email protected]) client-ip=75.127.100.175; Authentication-Results: mx.google.com; spf=neutral (google.com: 75.127.100.175 is neither permitted nor denied by best guess record for domain of [email protected]) [email protected] Received: from nimikri.nimikri.com (localhost.localdomain [127.0.0.1]) by nimikri.nimikri.com (8.14.3/8.14.3) with ESMTP id o3PH3A7a029986 for <[email protected]>; Sun, 25 Apr 2010 12:03:11 -0500 Date: Sun, 25 Apr 2010 12:03:10 -0500 From: Hour Jar <[email protected]> To: [email protected] Message-ID: <[email protected]> Subject: [email protected] has invited you to New Event MIME-Version: 1.0 Content-Type: text/html; charset=us-ascii Content-Transfer-Encoding: 7bit

  Read the article

• AD GIT SELinux RHEL 6 : Can not get SELinux to allow connetion to git

  - by Johan Sörell

  I have a problem with SELinux! I have installed git on Red Hat Enterprise 6 with AD group control and SSL Cert . Everything works fine if I do setenforce 0 ( set SELinux in detection only mode ) or if I do semanage permissive -a httpd_t (Set httpd_t in detection only mode) I do not want to use this on my git production server. Is there anyone out there who can help we with SELinux? Below is some info that you might need to be able to help me: All help I can get would be apriciated: This is the output of ls -lZa /preproduction/git/repositories/ ls -lZa /preproduction/git/repositories/ drwxr-xr-x. apache apache unconfined_u:object_r:httpd_sys_rw_content_t:s0 . drwxr-xr-x. apache apache unconfined_u:object_r:file_t:s0 .. drwxr-xr-x. apache apache unconfined_u:object_r:httpd_sys_rw_content_t:s0 playground drwxr-xr-x. apache apache unconfined_u:object_r:httpd_sys_rw_content_t:s0 shamrock.git drwxr-xr-x. apache apache unconfined_u:object_r:httpd_sys_rw_content_t:s0 test Here is the out put of getsebool -a |grep -i httpd getsebool -a |grep -i httpd allow_httpd_anon_write --> off allow_httpd_mod_auth_ntlm_winbind --> off allow_httpd_mod_auth_pam --> off allow_httpd_sys_script_anon_write --> off httpd_builtin_scripting --> on httpd_can_check_spam --> off httpd_can_network_connect --> off httpd_can_network_connect_cobbler --> off httpd_can_network_connect_db --> off httpd_can_network_memcache --> off httpd_can_network_relay --> off httpd_can_sendmail --> off httpd_dbus_avahi --> on httpd_enable_cgi --> on httpd_enable_ftp_server --> off httpd_enable_homedirs --> off httpd_execmem --> off httpd_read_user_content --> off httpd_setrlimit --> off httpd_ssi_exec --> off httpd_tmp_exec --> off httpd_tty_comm --> on httpd_unified --> on httpd_use_cifs --> off httpd_use_gpg --> off httpd_use_nfs --> off Tis is the status of : sestatus sestatus SELinux status: enabled SELinuxfs mount: /selinux Current mode: enforcing Mode from config file: enforcing Policy version: 24 Policy from config file: targeted

  Read the article

• SAS Expanders vs Direct Attached (SAS)?

  - by jemmille

  I have a storage unit with 2 backplanes. One backplane holds 24 disks, one backplane holds 12 disks. Each backplane is independently connected to a SFF-8087 port (4 channel/12Gbit) to the raid card. Here is where my question really comes in. Can or how easily can a backplane be overloaded? All the disks in the machine are WD RE4 WD1003FBYX (black) drives that have average writes at 115MB/sec and average read of 125 MB/sec I know things would vary based on the raid or filesystem we put on top of that but it seems to be that a 24 disk backplane with only one SFF-8087 connector should be able to overload the bus to a point that might actually slow it down? Based on my math, if I had a RAID0 across all 24 disks and asked for a large file, I should, in theory should get 24*115 MB/sec wich translates to 22.08 GBit/sec of total throughput. Either I'm confused or this backplane is horribly designed, at least in a perfomance environment. I'm looking at switching to a model where each drive has it's own channel from the backplane (and new HBA's or raid card). EDIT: more details We have used both pure linux (centos), open solaris, software raid, hardware raid, EXT3/4, ZFS. Here are some examples using bonnie++ 4 Disk RAID-0, ZFS WRITE CPU RE-WRITE CPU READ CPU RND-SEEKS 194MB/s 19% 92MB/s 11% 200MB/s 8% 310/sec 194MB/s 19% 93MB/s 11% 201MB/s 8% 312/sec --------- ---- --------- ---- --------- ---- --------- 389MB/s 19% 186MB/s 11% 402MB/s 8% 311/sec 8 Disk RAID-0, ZFS WRITE CPU RE-WRITE CPU READ CPU RND-SEEKS 324MB/s 32% 164MB/s 19% 346MB/s 13% 466/sec 324MB/s 32% 164MB/s 19% 348MB/s 14% 465/sec --------- ---- --------- ---- --------- ---- --------- 648MB/s 32% 328MB/s 19% 694MB/s 13% 465/sec 12 Disk RAID-0, ZFS WRITE CPU RE-WRITE CPU READ CPU RND-SEEKS 377MB/s 38% 191MB/s 22% 429MB/s 17% 537/sec 376MB/s 38% 191MB/s 22% 427MB/s 17% 546/sec --------- ---- --------- ---- --------- ---- --------- 753MB/s 38% 382MB/s 22% 857MB/s 17% 541/sec Now 16 Disk RAID-0, it's gets interesting WRITE CPU RE-WRITE CPU READ CPU RND-SEEKS 359MB/s 34% 186MB/s 22% 407MB/s 18% 1397/sec 358MB/s 33% 186MB/s 22% 407MB/s 18% 1340/sec --------- ---- --------- ---- --------- ---- --------- 717MB/s 33% 373MB/s 22% 814MB/s 18% 1368/sec 20 Disk RAID-0, ZFS WRITE CPU RE-WRITE CPU READ CPU RND-SEEKS 371MB/s 37% 188MB/s 22% 450MB/s 19% 775/sec 370MB/s 37% 188MB/s 22% 447MB/s 19% 797/sec --------- ---- --------- ---- --------- ---- --------- 741MB/s 37% 376MB/s 22% 898MB/s 19% 786/sec 24 Disk RAID-1, ZFS WRITE CPU RE-WRITE CPU READ CPU RND-SEEKS 347MB/s 34% 193MB/s 22% 447MB/s 19% 907/sec 347MB/s 34% 192MB/s 23% 446MB/s 19% 933/sec --------- ---- --------- ---- --------- ---- --------- 694MB/s 34% 386MB/s 22% 894MB/s 19% 920/sec 28 Disk RAID-0, ZFS 32 Disk RAID-0, ZFS 36 Disk RAID-0, ZFS More details: Here is the exact unit: http://www.supermicro.com/products/chassis/4U/847/SC847E1-R1400U.cfm

  Read the article

• Optical SPDIF audio from motherboard not working with receiver

  - by simon b

  Hi, I hope someone can help; I can't get my SPDIF optical out working through my receiver and all the responses I can see on the web assume you have a sound card, while I settled for the (seemingly high end) sound on my motherboard (Asus P7P55D-E PRO), which appears to limit some of my options. My set-up is a "new out of the box" one and is: *Windows 7 PC (using PowerDVD10 for DVDs/Blurays and Windows media player for music) *Asus P7P55D-E PRO motherboard - has 8-channel audio TRS jacks and SPDIF optical and coaxial out *An old Yamaha receiver, whose only multi-channel input options are optical in and 6 channel RCA in. However, it still can handle DTS and DD *Boston Acoustic Soundware XS 5.1 speakers I've currently got the SPDIF optical out from the motherboard connected to the in on my receiver, have SPDIF enabled in the sound menu and the light is glowing red down the fibre. But I'm getting no sound at all. What I want is to be able to play DVDs/BluRays in 5.1 but also to be able to play music in multi-channel mode (even though I know this will be "fake" multichannel; it's more about where I sit in the room and my requirement to use the sub because the Boston is a satellite/sub set-up) My questions are: *Will optical work at all for multi-channel? THe latest posts I can see suggest it does but some people seem to say optical only outputs stereo. Whom to believe? *Even if it does work, I've read that I have to disable AC-3 decoding, or make various other changes, which don't seem to be possible without the menu options that a sound-card brings. Is the motherboard-only option just too inflexible? *Although my SPDIF device is enabled in the sound menu, it insists under "Jack information" that it is a "rear panel RCA jack", when of course it is not (both TOSLINK and rCA jacks do exist). Has the PC just forgotten that it has an optical? *I think I could relatively easily connect the 8-channel 3.5mm TRS jacks to my receiver 6-ch input jacks by way of TRS/RCA cables, but would that not stop me from being able to play music from media-player in multi-channel mode, as I'm not sure the motherboard can cope *Or do I need to bite the bullet and buy a sound-card? And if so, how can I be sure the one I get doesn't have the same problem? Any thoughts gratefully received, Cheers, simon

  Read the article

• Windows XP machine not seeing external FAT32 partitions correctly

  - by Rob_before_edits

  About 8 months ago my Windows XP machine stopped being able to see FAT32 external drives when I plug them in... mostly. I will explain... It happens with all my FAT32 drives, whether they be unpowered external hard drives, powered external hard drives, SDHC cards plugged directly into the machine's card reader, or SDHC cards plugged in via a separate USB card reader. All of these drives/cards used to work fine on this machine. They all stopped working at about the same time. NTFS volumes are not affected. If I plug in NTFS external drives they are recognized right away. I even have one external drive with two partitions on it, one is NTFS which is recognized, the other is FAT32, which is not recognized. If I attach a FAT32 drive, then reboot, then the drive almost always becomes visible to the machine after the reboot. Sometimes I can plug in a FAT32 drive and it works right away. Not often though. I'd say I get lucky more often with SDHC cards than hard drives. I'm developing a theory that I only get lucky with hard drives if I'm running Acronis Disk Director when I plug them in, though that usually doesn't work either - I need more data here, this may be a red herring. Getting lucky with a hard drive is really rare, usually I have to reboot. When a FAT32 is recognized, either because I got lucky or because I rebooted, I can almost never safely disconnect it. It tells me "The device 'Generic volume' cannot be stopped right now. Try stopping the device again later". I can't seem to get around this. IIRC, I've tried closing every open window, and still no luck. Since I care about my data usually the only way to disconnect a FAT32 drive is to shut down the machine. As you can imagine, two reboots just to read a drive is getting pretty old... When the machine fails to see a FAT32 drive it usually comes up with the appropriate drive letter and the words "Local Disk" in Windows Explorer instead of the correct partition name. If I click on it I get "J:\ is not accessible. The parameter is incorrect." Before this problem arose I always clicked the "safely remove" button for everything, including SDHC cards where I think it's not necessary. I've known for a long time that this is the correct procedure for hard drives, so I don't think failing to do this was the cause of this problem (before someone asks :) Any answers or suggestions most welcome.

  Read the article

• SSD Fresh Does Not Start

  - by Jim Fell

  I recently installed a new 60GB SSD as my primary hard drive and re-installed Windows 7 Professional 64-bit. I then installed SSD Fress from Abelssoft to optimize Windows to run on the SSD. It seemed to install okay, but when I try to run the utility, its splash screen appears briefly before it quietly closes. No errors are displayed; the utility just fails to launch. I have run SSD Fresh on another SSD-equipped Windows 7 Pro x64 computer in the past without any problems. Does anyone know what might be preventing the program from running? I tried shutting down the Spybot Resident and disabling the firewall and virus scanner with no luck. I also tried running the tool as administrator; I even tried reinstalling it, running the installer as administrator. No luck. Every time I try to launch the program the Event Viewer logs this same set of errors: Error 4/2/2012 11:35:44 PM Application Error 1000 (100) Error 4/2/2012 11:35:43 PM .NET Runtime 1026 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None For those who are interested, here is my system configuration: ASRock M3A770DE AM3 AMD 770 ATX AMD Motherboard AMD Athlon II X3 455 Rana 3.3GHz Socket AM3 95W Triple-Core Desktop Processor ADX455WFGMBOX G.SKILL Value Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) Desktop Memory Model F3-10600CL9D-8GBNT Mushkin Enhanced Chronos Deluxe MKNSSDCR60GB-DX 2.5" 60GB SATA III Synchronous MLC Internal Solid State Drive (SSD) (Primary/Boot HD) Western Digital Caviar Blue RFHWD1600AAJS 160GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive (Secondary HD) Sony Optiarc CD/DVD Burner Black SATA Model AD-7261S-0B LightScribe Support RAIDMAX RX-850AE 850W ATX12V v2.3 / EPS12V SLI Certified CrossFire Ready 80 PLUS GOLD Certified Modular Active PFC Power Supply ASUS HD7850-DC2-2GD5 Radeon HD 7850 2GB 256-bit GDDR5 PCI Express 3.0 x16 HDCP Ready CrossFireX Support Video Card Asus ML228H 21.5" Full HD LED BackLight LED Monitor Slim Design (x3)

  Read the article

• How do I troubleshoot root cause of a hung windows (2003) server?

  - by GregW

  I have a pair of Windows (2003 Server) servers both running MS SQL Server (2008 EE) that each hang every few months. This has been occurring intermittently :( for the past 15 months pretty much since we started using the servers. The symptoms are as-follows: I cannot remote desktop in to troubleshoot; when I attempt to, I get stuck on a blank black screen and am never offered a login prompt I can still ping the servers I can still open a SQL connection to the server, and, CURIOUSLY/BIZARRELY, when I do a "select getdate()", the time it returns appears to be stuck on the exact fraction of a second when (I presume) the server hung. Repeated attempts to do "select getdate()" keep getting that same date, suggesting that the clock is frozen. Filesharing attempts to connect to the hung server fail with the error message: "\ServerName is not accessible. You might not have permissions to use this network resource. Contact the administrator of this server to find out if you have access permissions. The server's clock is not synchronized with the primary domain controller's clock." This is consistent with a frozen clock. Post-reboot, if I investigate the Windows Event Viewer logs, I can see many security accesses (coming from me and others) that I recognize were login attempts during the "down" period, but all of them in the security log are associated with that same timestamp of when the server hung. This also suggests the clock is frozen. There is not a clear cause in the Application or System event logs. I have a local Admin account on the server and am in the process of getting a domain-credentialed Admin account for better remote admin access. HP is supposed to be supporting these machines and has some low-level ILO2 access but they seem incapable of finding the root cause. A reboot will "fix" the problem but I would like to get to the root cause and solve the issue. Has anyone ever seen something like this odd clock behavior?! (If it were just one server I'd perhaps say a bad hardware clock, but two?) Can anyone advise me on what I should try to troubleshoot this sort of situation to find the root cause (or what I should tell HP to try?)

  Read the article

• RHEL5: Can't create sparse file bigger than 256GB in tmpfs

  - by John Kugelman

  /var/log/lastlog gets written to when you log in. The size of this file is based off of the largest UID in the system. The larger the maximum UID, the larger this file is. Thankfully it's a sparse file so the size on disk is much smaller than the size ls reports (ls -s reports the size on disk). On our system we're authenticating against an Active Directory server, and the UIDs users are assigned end up being really, really large. Like, say, UID 900,000,000 for the first AD user, 900,000,001 for the second, etc. That's strange but should be okay. It results in /var/log/lastlog being huuuuuge, though--once an AD user logs in lastlog shows up as 280GB. Its real size is still small, thankfully. This works fine when /var/log/lastlog is stored on the hard drive on an ext3 filesystem. It breaks, however, if lastlog is stored in a tmpfs filesystem. Then it appears that the max file size for any file on the tmpfs is 256GB, so the sessreg program errors out trying to write to lastlog. Where is this 256GB limit coming from, and how can I increase it? As a simple test for creating large sparse files I've been doing: dd if=/dev/zero of=sparse-file bs=1 count=1 seek=300GB I've tried Googling for "tmpfs max file size", "256GB filesystem limit", "linux max file size", things like that. I haven't been able to find much. The only mention of 256GB I can find is that ext3 filesystems with 2KB blocks are limited to 256GB files. But our hard drives are formatted with 4K blocks so that doesn't seem to be it--not to mention this is happening in a tmpfs mounted ON TOP of the hard drive so the ext3 partition shouldn't be a factor. This is all happening on a 64-bit Red Hat Enterprise Linux 5.4 system. Interestingly, on my personal development machine, which is a 32-bit Fedora Core 6 box, I can create 300GB+ files in tmpfs filesystems no problem. On the RHEL5.4 systems it is no go.

  Read the article

• Toshiba Satellite L630 broken after bios update

  - by Mustafa Kamal

  I have Toshiba Satellite L630, which has been broken. It had no more OS installed in it. All the disk partition were cleared into one single empty unformatted partition. So I begin to install windows XP on this laptop. Apparently, win XP's driver support for this laptop is very limited. So I have to find almost all important driver (display, sound, etherned, wireless etc) on the net and install it manually one by one. So I start googling, and I got some driver download page from several Toshiba's website (the global version, the europe, asia, etc). Pretty hard to find the exact drivers, but I managed to find pretty good drivers. It's all works quite fine, although still have a few glitches. But everything turned into a big mess when I downloaded the "BIOS Update", which is also listed on Toshiba's official driver directory site. When I installed it, it show a big red warning sign telling me not to do anything while flashing the BIOS . I follow that instruction prudently. The process was finished, and that update BIOS software (it is InsydeH2O BIOS) told me that the BIOS has been succesfully updated and the computer need to restart. So I restart the computer. This is where the problem appear. I can no longer boot to my laptop. The booting process seems to be able to enter windows for a moment (it shows the windows XP loading screen), and then suddenly it just got that hateful blue screen and then instantiy restarts the machine. It goes on a loop. Boot bios - enter XP - blue screen - restart. I can't even try to reinstall my win XP again. Evertime the machine tries to boot to win XP CD, it got the same blue screen as I gets when loading from HDD. Many google search results said that I should open the laptop cover and try to clear CMOS with some kind of jumper or something. Or to unplug/re-plug the CMOS battery. Do I really need to do that? Is there anyway I could do without disassembling my laptop? I read some tricks about booting from USB device but I can't get the exat tools that I need to do that thing... Btw, this is my detailed laptop number photographed from the back of my laptop

  Read the article

< Previous Page | 433 434 435 436 437 438 439 440 441 442 443 444  | Next Page >