Search Results

Search found 11687 results on 468 pages for 'ex networking guy'.

Page 44/468 | < Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >

• No Wireless In Ubuntu 13.10

  - by viktorhubinette

  When I upgraded to Ubuntu 13.10, I can't connect to wireless. The only thing I can connect to is ethernet, so please help me, What should I do? Here is the output of the lspci -nnk | grep -i net -A2 00:19.0 ethernet controller [0200]:intel corporation 82579V Gigabit network connection [8086:1503] (rev 04) subsystem: acer incorporated [ALI Device] [1025:8000] Kernel driver in use : e100e output of lsusb: Bus 002 Device 003: ID 046d:c31c Logitech, Inc. Keyboard K120 for Business Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 0bda:0152 Realtek Semiconductor Corp. Mass Storage Device Bus 001 Device 040: ID 04e8:6863 Samsung Electronics Co., Ltd Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 004: ID 0bda:8178 Realtek Semiconductor Corp. RTL8192CU 802.11n WLAN Adapter Bus 003 Device 003: ID 045e:070f Microsoft Corp. Bus 003 Device 002: ID 046d:c52f Logitech, Inc. Unifying Receiver Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

  Read the article

• RPC protocols comparison

  - by Ricardo

  I have to select a protocol/technology to use for communicating a client-server architecture, with support both for Python and C. The main requirements are: Symmetrical communication in between ends: clients establish a connection and servers can send data back to clients through the same connection. Avoid excessive overhead by using HTTP or a big stack (if possible, TCP direct communication). TLS/SSL support for secure communications. Ease of implementation. For that, I evaluated the following protocols/communications technologies. Is the information on this table accurate and correct? (*1) TLS support for RPyC is based in a no-longer supported Python library.

  Read the article

• Can't connect to or see my wifi ssid

  - by ant

  Today I installed ubuntu 12.04 on my laptop. I am unable to see my home SSID or even connect to it. I've tried to connect as a hidden SSID but I always get prompted for authorization although my key is correct. I'm in in Europe but my laptop is from US. I'm not sure if that is relevant. I've read around this site and saw something that has to do with setting the channel above 11. I'm not sure I did that correctly I did this : How to use Wi-Fi channels above 11? Did't help. I'm able to connect with cable but not via wifi either windows or linux. Other devices in my home can connect without any issues, even the kindle. Here is the screenshot from my router : Here is some additional info : lspci | grep -i network 08:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01) lspci -nnk | grep -A2 0280 08:00.0 Network controller [0280]: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01) Subsystem: Hewlett-Packard Company U98Z062.10 802.11bgn Wireless Half-size Mini PCIe Card [103c:303f] Kernel driver in use: ath9k m-tool NetworkManager Tool State: connected (global) Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: ath9k State: disconnected Default: no HW Address: 90:4C:E5:38:79:0D Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes I'm not sure what to do next. Any suggestions?

  Read the article

• How to share a folder without any issues when we have >20 machines in LAN ?

  - by Gaurang Agrawal

  Till date I have been sharing files through workgroup , using samba but I presume that this is not the right way as I had been facing so many issues with one or another computer . Machines are having same workgroup but even then problems are there . What will be the best way to handle this kind of issue ? PS : I am helping a school migrate from Windows to Ubuntu 12.04 LTS ( Teachers collaborate by working on different files saved in a shared folder in one of the computer )

  Read the article

• Yoga Pro 2 Wi-Fi not working

  - by user293004

  I installed Ubuntu 14.04 on my new Yoga Pro 2 and the wireless is not working. It started with Windows 8 on it. The Network Manager says Wi-Fi is disabled by hardware switch. I tried putting a blacklist file in ect/modprobe.d as has been suggested in many places. I called the file "blacklist-ideapad_laptop.conf" and wrote in the file blacklist ideapad_laptop I checked to make sure that the wireless is enabled in the BIOS. It is. I ran rfkill list all and it displayed: 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes I ran iwlist wlan0 scan and it displayed: wlan0 Failed to read scan data : Network is down I ran sudo rmmod ideapad_laptop and it displayed: rmmod: ERROR: Module ideapad_laptop is not currently loaded. I ran ifconfig wlp1s0 up and it displayed: wlp1s0: ERROR while getting interface flags: No such device. I ran "lspci" and it displayed: 01:00.0 Network controller: Intel Corporation Wireless 7260 (rev 6b) I ran sudo lshw -c network and it displayed: *-network DISABLED description: Wireless interface product: Wireless 7260 vendor: Intel Corporation physical id: 0<br> bus info: pci@0000:01:00:0.0 logical name: wlan0 version: 6b serial: 7c:7a:91:5f:9b:fa width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.13.0-24-generic firmware=22.24.8.0 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:61 memory:b0400000-b0401fff This No wireless with Intel Centrino Advanced-N 7260 seems to be dealing with a similar issue. It suggests that I need to update my firmware. So I downloaded iwlwifi-7260-ucode-23.214.9.0 from Intel's website. I put the file "iwlwifi-7260-9.ucode" in /lib/firmware and ran "sudo lshw -c network" again. It displayed exactly as before. Is there something else I need to do install the new firmware?

  Read the article

• both IPV4 and IPV6 at the same time over DSL connection?

  - by namiheike

  Let me describe my situation: while I connect computer with the wire, I've got an IPV6 address automatically, there's a "Wired connection" tab in network manager, and I can access an website that support IPV6 (google,facebook,twitter...)with a hosts file, or use the proxy like google.com.sixxs.org But if I want to access the whole internet, I have to create a DSL connection with username and password that ISP gave me. BUT after I change my connection into this DSL connection, I cannot access website over IPV6, even there's the site's ipv6 address in /etc/hosts, then I realize that I lose my IPV6 connection, because the ping6 says connect: Network is unreachable. the problem is, there's no IPV6 tab or options about IPV6 in the configure of DSL connection. It feels like I can only use one connection at the same time, but the DSL doesn't support IPV6 and the wired connection doesn't support IPV4(I mean, there's no way to input the password the ISP gave me) maybe make somebody uncomfortable, but when I work in MS windows, there's no such problem, (maybe just feel like) I can access V4 and V6 at the same time. So how to solve with this? thanks a lot. I'm in 11.10 + gnome3

  Read the article

• Is it possible to set a VPN through Tor? and have functionality for Software Updates?

  - by moazhmi

  Gday, I have been trying to do a software update on Trusty both on terminal and software update app but that hasnt been successful, apparently my ISP has a broken transparent proxy. moazhmi@moazhmi-K52F:~$ wget -S http://extras.ubuntu.com/ubuntu/dists/trusty/InRelease --2014-06-04 17:34:52-- http://extras.ubuntu.com/ubuntu/dists/trusty/InRelease Resolving extras.ubuntu.com (extras.ubuntu.com)... 91.189.92.152 Connecting to extras.ubuntu.com (extras.ubuntu.com)|91.189.92.152|:80... connected. HTTP request sent, awaiting response... HTTP/1.1 200 OK Content-Type: text/html; charset=UTF-8 Content-Length: 213 Date: Wed, 04 Jun 2014 14:34:52 GMT Server: Apache/2.2.22 (Ubuntu) Connection: Keep-Alive Vary: Accept-Encoding Length: 213 [text/html] Saving to: ‘InRelease’ 100%[======================================>] 213 --.-K/s in 0s 2014-06-04 17:34:52 (22.1 MB/s) - ‘InRelease’ saved [213/213] I was advised to refer back to the ISP with a complaint but that has returned with peanuts. My Question is - Is it possible to set a VPN through TOR , i.e whereas I can run software updates through terminals or the app . the browsing is out of question here as I need to update which I am not able to do / only on 12.04.

  Read the article

• Unable to connect to the Internet via LAN despite the connection showing as established

  - by Vikram

  I have installed Ubuntu 11.10. I am facing a problem connecting via LAN. We have a firewalled network. After entering static IP, gateway, DNS, etc., it shows connection as established but we are unable to use the Internet using the wired connection (LAN). While checking system testing following error shows under network test: ERROR:root:Could not find def gateway info in /proc ERROR:root:Could not find default gateway by running route

  Read the article

• wifi not working hp dv4

  - by Blaze

  i get this output for sudo lshw -C network : *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: 06 serial: 3c:4a:92:cd:63:98 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff *-network DISABLED description: Wireless interface product: RT5390 [802.11 b/g/n 1T1R G-band PCI Express Single Chip] vendor: Ralink corp. physical id: 0 bus info: pci@0000:0a:00.0 logical name: wlan0 version: 00 serial: 90:00:4e:82:3c:5b width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.0.0-17-generic-pae firmware=0.34 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:c2500000-c250ffff i cant enable the wifi using the fn+f12 key.. its just stuck. In windows 7 it gets enabled when i press the same keys. but this happens after it gets booted up... i just want to use the wifi in anyway possible. can anybody help?

  Read the article

• Ubuntu connects to wireless but doesn't work!

  - by UbuntuUser990

  I just installed Ubuntu 14.04 LTS on my laptop, it connects to my wireless network and shows that it is connected, but when I try to load a webpage or do anything like download Steam for Dota 2, it doesn't work. When I try to connect my Facebook account to Ubuntu, it doesn't work. I want to be able to use Ubuntu with working internet access. What do I do?. ifconfig this shows up eth0 Link encap:Ethernet HWaddr 88:ae:1d:60:56:eb inet addr:192.168.1.13 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:24 errors:0 dropped:0 overruns:0 frame:0 TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1856 (1.8 KB) TX bytes:1856 (1.8 KB) When I type ping askubuntu.com this shows up ping: unknown host askubuntu.com

  Read the article

• Dirt Cheap Bi-Directional Antenna Wirelessly Extends Your LAN

  - by Jason Fitzpatrick

  If you’re looking for an effective way to link remote LANs without the hassle of laying cable, this DIY bi-directional antenna is a quick (and cheap) method for bringing internet access to outbuildings and other locations. Tinker Danilo Larizza needed to share internet access between apartments that are relatively close together but not hardwired–ruling out simply sharing the access via existing LAN infrastructure. His solution combines a simple scrap wire antenna array mounted inside a plastic food bin (seen here with the cover removed to show the antenna) and some coaxial cable to link the antenna to two routers. Our favorite part about his build is that he constructed the pair to establish if the antenna setup would even work in his location and intended to buy commercial antennas if it did; his Tupperware models worked so well, however, they’re now the permanent solution. Hit up the link below for more information about the project. 2.4 Ghz Directive Biquad Antenna [via Hack A Day] How To Use USB Drives With the Nexus 7 and Other Android Devices Why Does 64-Bit Windows Need a Separate “Program Files (x86)” Folder? Why Your Android Phone Isn’t Getting Operating System Updates and What You Can Do About It

  Read the article

• Changing internal home network ip address for connected devices

  - by oshirowanen

  I have a few computers at home. For each of the computers, I can see the internal home network ip address on any given device by typing in ifconfig in the terminal. If the device is connected to the home network via ethernet connection or via the built-in wireless connections in laptops, the internal ip address for each of the devices seems to be 192.168.0.X. However, when I connect one of the devices using an external usb modem wireless adapter, which connects to the home network through wireless, when I check the ip address via ifconfig, for some reason it gets assigned 192.168.42.X instead. Why are the ethernet and build in wireless connections getting 192.168.0.X, but the external usb wireless adapter gets 192.168.42.X? Most importantly, is it possible to force it to get an internal ip address of 192.168.0.X?

  Read the article

• Can't connect to hidden network with BCM4313

  - by poomerang

  The wireless works fine with all the other wi-fi nets I have tried, the only problem is with this hidden network. I should add it's the only hidden network I've tried, so I am not sure if the problem is it being hidden or somethings else, but I've checked the settings of NetworkManager against another Ubuntu system (which can connect) and they appear to be the same, passphrase included. The network is using WPA2 Personal with AES encryption, I don't know how to check this setting but I believe it's the usual for WPA2, and therefore usually not a problem. Also, I can connect through ethernet, which should exclude any blacklisting of my device, I believe. I usually use brcmsmac drivers, I've tried also STA but the result is the same. I've also tried the suggestion from Unable to connect to hidden SSID with no luck output of lspci -v is 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Askey Computer Corp. Device 7175 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at d4000000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: bcma, brcmsmac

  Read the article

• MAAS and Openstack Network

  - by user281985

  Trying to figure out the best way for openstack and MASS networks to co-exist. Assuming MAAS used 10.0.0.0/24 for provisioning of various openstack nodes, once openstack, with quantum, is deployed should 10.0.0.0 be used as management network, external network, both or discarded? Reason for the question being that I ran a deployment where openstack used 10.0.0.0 as its management network, MAAS dhcp and dns were active; however, I could only access VMs through namespace and was not able to utilize MAAS's dhcp to assign floating IP. (VMs network was through an internal bridge 10.10.10.10, and external bridge was using the same interface as MAAS.) Any thoughts or ideas are appreciated.

  Read the article

• MAAS. Adding nodes

  - by 2bus.erkanat

  Can anybody help me with MAAS installation? I installed it on 1 of my computers, configured DHCP server and now 3 PCs are in their own private network. I tried to add node via PXE image, but "Can not apply stage final, no datasource found! Likely bad things to come!" error comes after giving me option to log in. Then I tried to add node via web interface, but after adding it node's status is always "commisioning". So what should I do know? Any help is appreciated. Thank you P.S. English is not my native language, sorry for any type of errors.

  Read the article

• Simple NAS setup for Ubuntu

  - by Sean Houlihane

  So, I want to connect my shiny new NAS (QNAP TS-210p II) to my Ubuntu 11.10 box. I have a 2nd Ubuntu machine, but I don't use that enough to be too worried about it. Use is ideally to offload all storage except for system (which can then run off a 30GB flash drive). The main machine also runs Myth front/backends. Both are on a wired network currently. I have got a basic setup working, mounted over NFS, but have some issues, and whenever I look for answers, I seem to get unto the UbuntuServer domain, with what seems like more detail than I want in an answer. Questions I have identified so far: 1) Sharing UIDs to get file permissions correct. LDAP or something else? What is necessary to make this work? 2) Mounting an NFS device reliably. Do I just add it in fstab or is some sort of auto-mount advisable? Its a wired network, but I shouldn't need to worry about reboot after power-outages and sequencing...

  Read the article

• How to run a local and external website on same computer with 2 NIC's, 2 Routers and 3 seperate networks?

  - by CandN

  Hello and hopefully I can get some answers to my question, though I think I'm making it more complicated for myself than it has to be. My business is a used auto dealership, and I'm in the process of connecting it to the world - via ethernet from the business server [running Xubuntu] to the ISP's ethernet router/modem, so that I can host our own website (no more than 5-10 people probably visiting at any time - mainly paying their bill), as well as set up a web based internal-intranet site - via DD-WRT Router on the 2nd NIC on the business server - that'll be accessed over Wifi from employees personal devices. On the other end of this is trying to offer free wifi to customers that is completely seperate of the 2 mentioned above networks. Quick Rundown: 1. Web Site for Customers to access. I'm going to use no-ip.org for DNS for the moment being, so I'll have a site that customers can access from anywhere in the world at "mybiz.no-ip.org". This will be forwarded to NIC #1 on the server, possibly at an address like "108.69.." as its being provided an IP from the ISP's modem/router, that is from Time Warner, and they allow NO! configuration options. Web Site for employees to access. I'm trying not to use the server too much as a desktop, only for critical situations, so having a backend thats seperate from the front-facing website is critical. This will be the DD-WRT router hardwired into NIC #2 on the server. This WiFi will be password accessible. Public WiFi for customers. The DD-WRT can seperate networks if I'm correct, I just can't seem to understand how to seperate the 2 and still have internet access on both. I've done it before, but the "Public" wifi (with no password set to connect) kept dropping the connection like a problem was happening that I couldn't figure out. So if I could do a little drawing, this is how it would/should possibly look. ISP -- [Sends Public Facing IP of 108.69.*.1/8] -- ISP Modem Router ISP Modem Router (Ethernet Only) -- [Gives Private IP 108.69.*.2] -- Server NIC #1 Server NIC #1 -- [Gives Private IP 108.69.*.3] -- DD-WRT Router DD-WRT Router -- [DHCP Enabled Giving IP's 172.16.0.0/16] -- Employees Network | | --------- [DHCP Enabled Giving IP's 192.168.1.0/24] -- Public WIFI Hope it's not too confusing, but it anyone could give me some good direct tutorials on how to accomplish this, or if YOU know, then it'll be alot of help. Thanks to all in advance. Need anything else to be explained? Don't hesitate to ask! *Using The LAMP stack with Webmin/VirtualMin -Customer site is located in /var/www2/ -Private Employees site is located in /var/www/ Using no-ip.org's dynamic client updater

  Read the article

• Physics not synchronizing correctly over the network when using Bullet

  - by Lucas

  I'm trying to implement a client/server physics system using Bullet however I'm having problems getting things to sync up. I've implemented a custom motion state which reads and write the transform from my game objects and it works locally but I've tried two different approaches for networked games: Dynamic objects on the client that are also on the server (eg not random debris and other unimportant stuff) are made kinematic. This works correctly but the objects don't move very smoothly Objects are dynamic on both but after each message from the server that the object has moved I set the linear and angular velocity to the values from the server and call btRigidBody::proceedToTransform with the transform on the server. I also call btCollisionObject::activate(true); to force the object to update. My intent with method 2 was to basically do method 1 but hijacking Bullet to do a poor-man's prediction instead of doing my own to smooth out method 1, but this doesn't seem to work (for reasons that are not 100% clear to me even stepping through Bullet) and the objects sometimes end up in different places. Am I heading in the right direction? Bullet seems to have it's own interpolation code built-in. Can that help me make method 1 work better? Or is my method 2 code not working because I am accidentally stomping that?

  Read the article

• Network does not connect at boot

  - by Daniel Svozil

  I am on Ubuntu 12.04, fresh install. When I boot a machine, the boot screen says Connecting to network, later it is changed to something like Did not connect, trying for another 60s. However, the network does not connect at the boot. But I can then log in without a network connection, and if I start a network manager service manually from the terminal (sudo service network-manager start), the network is connected without any problems. Please, does anybody know where the problem could be? I don't want to wait more than two minutes every computer restart :-). I am new to Ubuntu (and also to upstart) so I am a bit lost. There is no /var/log/messages, in dmesg I found this record, though it may not be related: init: network-interface (eth1) pre-start process (492) terminated with status 1 init: network-interface (eth1) post-stop process (548) terminated with status 1 Thanks Daniel

  Read the article

• Lost network interface after mac change

  - by Arturo Grc

  I'm using Ubuntu server 12.04 inside Virtualbox and everything was working as expected, but since I changed the mac address in Virtualbox network settings the network interface is not being recognized on Ubuntu. I don't remember the old mac address and everytime Ubuntu starts shows waiting for network configuration when I use ifconfig only appears lo (loopback device) and eth0 is lost, how can I fix this problem?

  Read the article

• Cannot establish Wired connection on Acer Aspire 5930G

  - by drakos46

  I use an Acer Aspire 5930G, dual booted with Windows 7 and Ubuntu 13.10. My problem is that i cannot establish wired connection on my ubuntu. Wireless connection works in both of my OSs but the Wired connection does not, only on the Ubuntu. I have already tried the common fix: echo on | sudo tee /sys/class/net/eth0/device/power/control but without any results. Any ideas? eth0 Link encap:Ethernet HWaddr 00:1d:72:c2:21:a5 inet6 addr: fe80::21d:72ff:fec2:21a5/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:945 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:204318 (204.3 KB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:7241 errors:0 dropped:0 overruns:0 frame:0 TX packets:7241 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:645874 (645.8 KB) TX bytes:645874 (645.8 KB) wlan0 Link encap:Ethernet HWaddr 00:16:ea:57:7b:cc inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::216:eaff:fe57:7bcc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:19937 errors:0 dropped:0 overruns:0 frame:0 TX packets:16933 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10877245 (10.8 MB) TX bytes:3131378 (3.1 MB) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8071 PCI-E Gigabit Ethernet Controller (rev 16)

  Read the article

• How do I find out which process is eating up my bandwidth?

  - by Bruce Connor

  I think I'm being the victim of a bug here. Sometimes while I'm working (I still don't know why), my network traffic goes up to 200 KB/s and stays that way, even tough I'm not doing anything internet-related. This sometimes happens to me with the CPU usage. When it does, I just run a top command to find out which process is responsible and then kill it. Problem is: I have no way of knowing which process is responsible for my high network usage. Both the resource monitor and the top command only tell me my total network usage, neither of them tells me process specific network info. Is there another command I can use to find out which process is getting out of hand? I've already tried killing all the obvious ones (firefox, update-manager, pidgin, etc) with no luck. So far, restarting the machine is the only way I found of getting rid of the issue. EDIT: (just to be clear) I've found questions here about monitoring total bandwidth usage, but, as I mentioned, that's not what I need. UPDATE: The command iftop gives results that disagree entirely with the information reported by System Monitor. While the latter claims there's high network traffic, the former claims there's barely 1 KB/s. Thanks

  Read the article

• Wireless is disabled by hardware switch on Dell Inspiron 1750

  - by lowerkey

  I have a problem where Ubuntu (12.04) says there is a wireless network card, but it is disabled by a hardware switch. How do I turn it on? I checked the BIOS, and the wireless card is enabled there. Fn + F2 was also no success. The results of rfkill list: 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes sudo rfkill unblock wifi did nothing to the Wireless Status.

  Read the article

• Which game logic should run when doing prediction for PNP state updates

  - by spaceOwl

  We are writing a multiplayer game, where each game client (player) is responsible for sending state updates regarding its "owned" objects to other players. Each message that arrives to other (remote) clients is processed as such: Figure out when the message was sent. Create a diff between NOW and that time. Run game specific logic to bring the received state to "current" time. I am wondering which sort of logic should execute as part of step #3 ? Our game is composed of a physical update (position, speed, acceleration, etc) and many other components that can update an object's state and occur regularly (locally). There's a trade off here - Getting the new state quickly or remaining "faithful" to the true state representation and executing the whole thing to predict the "true" state when receiving state updates from remote clients. Which one is recommended to be used? and why?

  Read the article

• Trying to configure samba share with office server

  - by tomphelps

  Hi, i'm trying to set up fstab to automatically connect to my office shared server. I'm undoubtedly doing something silly here as the username and password and server name work fine in the first code snippet below, just not the second - any help would be appreciated! The following command works as expected... tom@tom-desktop: sudo /usr/bin/smbclient -L Server.local -Uguest Enter guest's password: Domain=[WORKGROUP] OS=[Unix] Server=[Samba 3.0.10] Sharename Type Comment --------- ---- ------- Lacie Disk Disk macosx Server Disk macosx IPC$ IPC IPC Service (Server) ADMIN$ IPC IPC Service (Server) Domain=[WORKGROUP] OS=[Unix] Server=[Samba 3.0.10] Server Comment --------- ------- ACER-9D60040D10 SERVER Server Workgroup Master --------- ------- WORKGROUP ACER-9D60040D10 But when i add the following line to /etc/fstab, i get this error: cifs_mount failed w/return code = -22 //Server.local/Server /media/maguires cifs username=guest,password=password 0 0

  Read the article

< Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >