Search Results

Search found 11687 results on 468 pages for 'ex networking guy'.

Page 50/468 | < Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >

  • Wireless Disabled (Network Manager)

    - by Peter Kihara
    Am Having issues with My Wireless 1 My laptop had dual boot windows 7 and Ubuntu 13.04 I upgraded to windows 8 and after the first 2-3 reboots all was working well in windows and ubuntu then my wireless in ubuntu stoped working saying "wifi is disabled by hardware switch" the hardware switch has no effect I removed network manager installed new firmwares and still nothing the wifi was not working in a moment of testing I installed wifi radar and this can detect the wireless signals and at one point it connected but still Network manger still says disabled. My Laptop is a HP Pavilion dm4 2070us with Wireless Centrino N 1000 I have updated to 13.10 thinking it would fix it but still nothing

    Read the article

  • Cannot connect to windows share

    - by BCqrstoO
    I've been going through and pouring over resource for the past few hours and I cannot get my box to connect to my friends network drive. My friend doesn't use linux, but he's setup the network share like this: DPR:\\name\images and he's given me the username and password which I've verified is correct. It is located on 192.168.0.2 sudo mount -t cifs -o username=***,password=*** //name/images /media/name/ sudo mount.cifs //192.168.0.2/name/images /media/name/ -o credentials=~/name.credentials (I've confirmed that ~/name.credentials does have the correct credentials as well) Regardless of what I attempt I get mount error(13): Permission denied Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) I'm not sure what I'm doing wrong, but it's probably really simple and stupid. Thanks to any/all in advance. EDIT: I don't know if this helps, but I'm running Ubuntu 14.04.

    Read the article

  • All my bandwidth eaten up - report included

    - by Mel
    I have my network bandwidth eaten up totally. Whenever I connect my network, without any application being opened it is always full. I have prepared report of iftop, nethogs and network system monitor. iftop and nethogs My host IP is 192.168.1.203 and all the rest are not known though I have tried to pin 192.168.1.105, it doesn't reply. If possible I would like to block the most disturbing IP which is 192.168.1.105 to block it. but don't know how.

    Read the article

  • Internet stopped working suddenly on 12.04

    - by Daniel
    My laptop was running smoothly until yesterday. Today, I can't connect to the Internet at home anymore. I am only able to access the router, but no Internet access. A have a Dell Latitude E6320 with Ubuntu 12.04. At my job, I don't have any problems connecting this laptop both via Wireless and Ethernet. At home, if I try connecting it through Windows, it does work fine. I even checked the MAC address and it's OK. My other laptop, which also runs Ubuntu, is not facing this problem. I have already tried to restart and downgrade network-manager package and its dependencies. Can anyone help me please? I am afraid, I will have to reinstall everything.

    Read the article

  • How can I work out how many IP addresses there are in a given range?

    - by Jarede
    I'm wondering if there is a formula to work out the amount of IP addresses in a given range. I have a system that takes either a single IP address or a start and and end IP address: A single one might be: 145.16.23.241 A range might be: 145.16.23.122 - 145.16.23.144 The people inputting these aren't technical, nor are they receiving these details from technical people, so suggesting using CIDR notation isn't an answer for me. I want to be able to highlight that when entering a range such as: 122.100.10.12 - 128.10.200.140 it might not actually be a range and rather 2 singular IP addresses since such a range would comprise of x (large number of) IP addresses. Is there a basic formula to help me highlight this?

    Read the article

  • How to set up an ethernet and wireless network using /etc/network/interfaces?

    - by den-javamaniac
    Hi. Currently I have ethernet and wireless networks configured through a network manager (further NM) but it seems to be a bit buggy (I need a different MAC for ether which is never applied if using NM), so I would like to move all the network configs to interfaces file. I know (or can google for) configuration code, but I'm not sure how NM works and it looks like it overrides interface config. Please advice, how I can handle this issue. NOTE: I also would like to be able to locate and connect to various wireless networks but not sure how to do it.

    Read the article

  • Internet slow on one router only [the problem only in Ubuntu] [on hold]

    - by mrSuperEvening
    Internet works perfectly on every other router, but browsing sucks at home (slow browsing and slow loading times). I changed DNS servers to 8.8.0.0, still doesn't help. And funnily, download speed is extremely high on this network (meaning torrents for example), but using browsers and loading websites is extremely slow (only on this network). Do I need to change something in router settings or what can I try? By the way, I use wired connection to router. EDIT: There's no problems when using Windows. EDIT: ifconfig: eth0 Link encap:Ethernet HWaddr f2:4d:a0:c0:3f:4c inet addr:192.168.11.8 Bcast:192.168.11.255 Mask:255.255.255.0 inet6 addr: fe80::f24d:a2ff:fec6:3f4c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:206798 errors:0 dropped:0 overruns:0 frame:0 TX packets:219570 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:76680734 (76.6 MB) TX bytes:21738160 (21.7 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:160 errors:0 dropped:0 overruns:0 frame:0 TX packets:160 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:11094 (11.0 KB) TX bytes:11094 (11.0 KB)` ping -c 2 4.2.2.2 PING 4.2.2.2 (4.2.2.2) 56(84) bytes of data. --- 4.2.2.2 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms ping -c 2 google.com PING google.com (213.159.32.147) 56(84) bytes of data. 64 bytes from lan-213-159-32-147.kns.skynet.lv (213.159.32.147): icmp_seq=1 ttl=61 time=0.936 ms 64 bytes from lan-213-159-32-147.kns.skynet.lv (213.159.32.147): icmp_seq=2 ttl=61 time=0.937 ms --- google.com ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1001ms rtt min/avg/max/mdev = 0.936/0.936/0.937/0.030 ms

    Read the article

  • A simple example of movement prediction

    - by Daniel
    I've seen lots of examples of theory about the reason for client-side prediction, but I'm having a hard time converting it into code. I was wondering if someone knows of some specific examples that share some of the code, or can share their knowledge to shed some light into my situation. I'm trying to run some tests to get a the movement going (smoothly) between multiple clients. I'm using mouse input to initiate movement. I'm using AS3 and C# on a local Player.IO server. Right now I'm trying to get the Client side working, as I'm only forwarding position info with the client. I have 2 timers, one is an onEnterFrame and the other is a 100ms Timer, and one on mouseClick listener. When I click anywhere with a mouse, I update my player class to give it a destination point On every enterFrame Event for the player, it moves towards the destination point At every 100ms it sends a message to the server with the position of where it should be in a 100ms. The distance traveled is calculated by taking the distance (in Pixels) that the player can travel in one second, and dividing it by the framerate for the onEnterFrame handler, and by the update frequency (1/0.100s) for the server update. For the other Players, the location is interpolated and animated on every frame based on the new location. Is this the right way of doing it?

    Read the article

  • Wireless connected but internet not working, modem is fine because I'm typing over wifi on my android

    - by Sandro Livaja
    I can't connect to the Internet in 11.10. I tried switching my wifi card to another USB slot but nothing changed. Is it possible that the card is able to connect while not being able to receive packages? $ ifconfig eth0 Link encap:Ethernet HWaddr 40:61:86:35:11:b0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 Base address:0x6000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 74:ea:3a:8c:d5:5c inet addr:192.168.2.5 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::76ea:3aff:fe8c:d55c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1209 (1.2 KB) TX bytes:15329 (15.3 KB)

    Read the article

  • Computer becomes unreachable on lan after some time

    - by Ashfame
    I work on my laptop and ssh into my desktop. I use a lot of key based authentication for many servers for work but recently I couldn't login because ssh would pick up and try all the keys and it stops trying before ultimately falling back to password based login. So right now I am using this command: ssh -X -o PubkeyAuthentication=no [email protected] #deskto The issue is after sometime the desktop would just become unreachable from laptop. I won't be able to open its localhost through IP and today I tried ping'in it and found a weird thing. Instead of 192.168.1.4, it tries to ping 192.168.1.3 which I am sure is the root cause as it just can't reach 192.168.1.4 when its actually trying for 192.168.1.3 Ping command output: ashfame@ashfame-xps:~$ ping 192.168.1.4 PING 192.168.1.4 (192.168.1.4) 56(84) bytes of data. From 192.168.1.3 icmp_seq=1 Destination Host Unreachable From 192.168.1.3 icmp_seq=2 Destination Host Unreachable From 192.168.1.3 icmp_seq=3 Destination Host Unreachable From 192.168.1.3 icmp_seq=4 Destination Host Unreachable From 192.168.1.3 icmp_seq=5 Destination Host Unreachable From 192.168.1.3 icmp_seq=6 Destination Host Unreachable From 192.168.1.3 icmp_seq=7 Destination Host Unreachable From 192.168.1.3 icmp_seq=8 Destination Host Unreachable From 192.168.1.3 icmp_seq=9 Destination Host Unreachable ^C --- 192.168.1.4 ping statistics --- 10 packets transmitted, 0 received, +9 errors, 100% packet loss, time 9047ms pipe 3 Also the ping command message comes in multiple and not one by one. (izx answer's the weirdness I thought there was in ping command.) I did check for desktop, its local IP is still the same, so something is going on in my laptop. Any ideas? P.S. - Laptop runs Ubuntu 12.04 & Desktop runs Ubuntu 11.10 Laptop is connected through wifi to router and Desktop is connected through LAN to router. Update: Even after setting up static IP leases in router settings, I again ran into this issue.

    Read the article

  • keep getting added to hosts.deny + iptables

    - by Sc0rian
    I am confused to why this has started to happen. On my local network, if I click 10-20 apache/http links my server will decide to add me hosts.deny file and block me on iptables. Its not just apache, it seems to happen with any kinda of traffic, that comes in on a flood method. Like I use subsonic, if I change tracks 10-20 times, it will do it. I would assume I have some sort of firewall which is sitting on the server which is doing this. However I do not have fail2ban or any denyhosts in /var/lib. I cannot work out why I keep getting added to hosts.deny/iptables. Thanks

    Read the article

  • Internet unusably slow with Realtek Semiconductor Co., Ltd. RTL8111/8168B card

    - by user42424
    So I have recently installed Ubuntu 11.10 for a dual boot with wind 7. After the install I had like 300 updates, so I installed them. At first I could use the internet, although it was extremely slow. However now I cannot, sometimes it will load and others it will simply time out. When I try to download something it will either take forever or will not at all. This is a wired system. On Windows side my speeds are fine. Any help would be greatly appreciated. Also like I said I am new to Linux/Ubuntu so please be nice. One last thing, I also installed 11.10 for same dual boot on my laptop, and wireless speed is the same as on Windows? Only the wired desktop gives me the problem? Hear is some hardware info.. Hope it helps. Mobo: Gigabyte GA=880GMA- AMD / CPU: AMD Phenom (tm) IIx4 965 / 16 GB Ram / Realtek PCIe GBE Family Controller / Cisco Linksys E2000 / Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) / eth0 Link encap:Ethernet HWaddr 50:e5:49:33:64:cf inet addr:192.168.1.118 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::52e5:49ff:fe33:64cf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:76722 errors:0 dropped:76722 overruns:0 frame:76722 TX packets:49692 errors:0 dropped:65 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107956638 (107.9 MB) TX bytes:4342553 (4.3 MB) Interrupt:44 Base address:0x2000 thanks to roadmr problem solved! I powered down PC, un plugged power from pc end, waited a few (maybe 3)minutes. plugged power back in, pushed and held power button for 30 + seconds. Let go, powered on PC, and my Internet is fine! downloads and web speed blaze, just like on my Win 7 boot, maybe even faster. Problem Solved, Thanks to all!! **

    Read the article

  • No Sound from Shared Media

    - by Travis
    I have a shared media folder that I have all of my mp3's in. When I try to play them using Ubuntu, I get no sound, but the media player (Rhythmbox, Exaile, etc) display that they are playing the file, it looks like everything is playing but no sound. I have checked and rechecked the volume levels of the system and each application and I see no issues. If I move a file to the local drive, it plays just fine. I do sound checks while the file is playing and I get audio (front left, front right) from the test but not from the media file that I am playing. Any help would be greatly appreciated.

    Read the article

  • My internet connection slows or dies unexpectedly

    - by genesis
    I installed Ubuntu 10.04 once again and I'm having some problems which I had before, but I have no idea how I solved them. On Windows, everything's working fine and I had no problems with this. My problem is that sometimes, when browsing through the internet, webpages just start to load really slow, sometimes it doesn't load anything at all (Error 118 (net::ERR_CONNECTION_TIMED_OUT): The operation timed out.) and it starts to work after few minutes. My IPv4 settings are automatic (DHCP), and IPv6 settings are Ignored/Disabled. I think my previous problems had something to do with IPv6, but I'm not sure. Is there a fix for this? iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Fsite1" Mode:Managed Frequency:2.442 GHz Access Point: C8:3A:35:40:43:68 Bit Rate=0 kb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on Link Quality=43/70 Signal level=-67 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0

    Read the article

  • No Wireless Networks, BCM4313 [duplicate]

    - by TalonPlz
    This question already has an answer here: How to Install Broadcom Wireless Drivers (BCM43xx) 38 answers Just bought this little Asus 10 inch laptop that came with Ubuntu 12.04. Everything at my home was fine: Wireless identified and connected. As soon as I went to my girlfriend's house the trouble started. I couldn't connect to wireless (authentication... times out and asks for authentication) I started doing internet searching, tried a few solutions posted on line using terminal commands. No solutions. I decided to upgraded to 12.10-13.04 and that left me with a worse problem: I can no longer see ANY networks what so ever. Wireless card is ON, with out a doubt. Wired connection works. I have been fumbling with driver versions to no .avail, and have no idea which driver I am currently running I have a vague idea of what terminal lines to run: lshw: resources: irq:17 memory:f7d00000-f7dfffff *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth2 version: 01 serial: dc:85:de:56:c4:ea width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.20.155.1 (r326264) latency=0 multicast=yes wireless=IEEE 802.11abg resources: irq:17 memory:f7d00000-f7d03fff iwconfig: eth1 no wireless extensions. eth2 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off lo no wireless extensions. I am new and excited to start my Ubuntu and Linux life and this is only the first of my few hic cups i am sure! :) Thanks all UPDATE: Report from 2nd answer talon@Black1015E:~$ sudo apt-get remove --purge bcmwl-kernel-source [sudo] password for talon: Reading package lists... Done Building dependency tree Reading state information... Done Package 'bcmwl-kernel-source' is not installed, so not removed 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. talon@Black1015E:~$ wget http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb --2013-10-22 18:50:32-- http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb Resolving us.archive.ubuntu.com (us.archive.ubuntu.com)... 2001:67c:1562::15, 2001:67c:1562::13, 2001:67c:1562::14, ... Connecting to us.archive.ubuntu.com (us.archive.ubuntu.com)|2001:67c:1562::15|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1181334 (1.1M) [application/x-debian-package] Saving to: ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ 100%[======================================>] 1,181,334 3.37MB/s in 0.3s 2013-10-22 18:50:33 (3.37 MB/s) - ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ saved [1181334/1181334] talon@Black1015E:~$ arvh No command 'arvh' found, did you mean: Command 'arch' from package 'coreutils' (main) arvh: command not found talon@Black1015E:~$ arch x86_64 talon@Black1015E:~$ sudo dpkg -i bcmwl*.deb Selecting previously unselected package bcmwl-kernel-source. (Reading database ... 171895 files and directories currently installed.) Unpacking bcmwl-kernel-source (from bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb) ... Setting up bcmwl-kernel-source (5.100.82.112+bdcom-0ubuntu3) ... Loading new bcmwl-5.100.82.112+bdcom DKMS files... First Installation: checking all kernels... Building only for 3.8.0-32-generic Building for architecture x86_64 Building initial module for 3.8.0-32-generic Done. wl: Running module version sanity check. - Original module - No original module exists within this kernel - Installation - Installing to /lib/modules/3.8.0-32-generic/updates/dkms/ depmod........ DKMS: install completed. Error: Module b43 is not currently loaded Error: Module b43legacy is not currently loaded Error: Module ssb is not currently loaded Error: Module bcm43xx is not currently loaded Error: Module brcm80211 is not currently loaded Error: Module brcmfmac is not currently loaded update-initramfs: deferring update (trigger activated) Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.8.0-32-generic rebooting now

    Read the article

  • Syncing properties across a game server

    - by Vaughan Hilts
    I'm beginning to implement a simple scripting system into my networked server, and I've hit a snag. Before, I've been wrapping my calls into functions on objects that manipulate objects, but lately I've been finding this to be a pain for simple things. For example, if I set 'player.HP = 1'.. this works server-side. But the player side never sees this change unless I explicitly send a packet to inform the client. For many things like map swapping that require more complicated changes, like change X, Y, Map and do this.. I have a function. That's fine. But what about these small properties I want to sync?

    Read the article

  • SS7(M3UA, SCCP, TCAP, MAP) Stack

    - by Ammar Hameed
    I'm building an open source SMSC from scratch; it's almost finished, The SRI and the forwardSM operations are working, but I still have few things to do for the receiving part. I've built the SS7 stack already, but I'm using DB for saving the TCAP transactions IDs to be updated later to get/generate responses. My approach is this: I created memory table (heap table), saved the TCAP TID in the database, then compared the received TCAP TID with the TIDs saved in the database and then decide whether to end the TCAP session or continue. What is the best way to implement it? I'm thinking of doubly linked list that holds the TCAP TID. Am I going towards the right direction, or should I use another technique other than database or D-linked list? Should I leave it as it is, and let the database do the job for saving the TIDs? Please note that I'm using SCTP implementation available on Linux (lsctp) as a transport protocol, the language I'm using is C and the DB is MYSQL.

    Read the article

  • How do I get my RTL8192ce based wireless device working properly?

    - by JonnyTruelove
    I am using the rtl8192cu chipset (on a Belkin wireless USB adapter N300) combined with 64 bit architecture and the 3.8 kernel. Some of you may know that this doesn't work. I tried this fix - RTL8188CU USB Network Adaptor on ubuntu 13.04 and now my internet is super slow. I am totally new to Ubuntu and I am concerned I do not have the right driver. The "stock" driver was the RTL8192cu, but it didn't connect 99% of the time and if it did the upload speed was higher than the download. Right now I am connecting through my laptop with a crossover cable, so my internet connection is just fine in my apartment. Relevant output from lsusb is here: Bus 002 Device 002: ID 050d:2103 Belkin Components F7D2102 802.11n N300 Micro Wireless Adapter v3000 [Realtek RTL8192CU] (bonus question: is that [050d:2103] the actual physical address straight from the hardware? Or does it change when I put different drivers on it? I am concerned I do not have the right driver)

    Read the article

  • Creating a new DHCP lease databse

    - by Stee1bear
    I have Ubuntu Server set up as my DCHP server. We have had it install for a few year and our dchp.lease file contain over 4000 entries. I am wanting to clean it up and basically start a new lease file to get current list (@1500 entries). I have read the walk through on how to make a new lease file and get it started, which leads me to this question. Will the dhcp server try to give each unit new IP address or will it build the new database with the IP addresses that the the units report to it?

    Read the article

  • Multicast in Ubuntu

    - by iwant2learn
    Can some one please explain the steps required to configure a multicast in Ubuntu? I have a simple program taken from Internet. I get errors when I execute the client program. I get the error as: Opening datagram socket....OK. Setting SO_REUSEADDR...OK. Binding datagram socket...OK. Adding multicast group error: No such device: When I execute the server program I get the error as: Opening the datagram socket...OK. Setting local interface error: Cannot assign requested address I am using Ubuntu to run the program. I have two different laptops but connected via the same network. I am using wireless network to perform the above operation.

    Read the article

  • How to connect ethernet on ubuntu (with auto-detection by Ubuntu)

    - by user12285
    Do I need to post another thread for the same? If so, sorry. Yes, I saw that it's been well over six months but I have the same router SmartAX MT880d with ethernet, and the exact same problem, that is no internet even though I can successfully reach the modem settings page by entering 192.168.1.1 in Firefox. Sorry if I don't use the right (technical) terminology to express my issue. English is not my mother tongue. I'm a total beginner with ubuntu. My internet works great in Windows but does not work in Ubuntu. For 2 weeks, I've kept reading on the web and forums and the ubuntuguide.org to name a few but to no avail. Now I see no other solution but to ask for help. My problem is that as a beginner, I can't find a way to put the right digits in the right place because I don't know what numbers I need to put in what files (eg: do I need to use DHCP? or a static IP address? No clue whatsoever. I'm confused between putting figures in the wrong spaces. For example, is the modem/router's IP exactly 192.168.1.1 for Huawei Smart AXMT880d modem?? Is the subnet 255.255.255.0? Gateway 192.168.1.1. I'm confused as I can also see a different IP starting with 155131*** (is it an account number? no clue again) on my contract with Huawei (a Chinese ISP). Apart from calling 911, what other numbers do I need to put in and where? How do I check that all the numbers have been entered correctly in every appropriate space before trying to connect the Internet?

    Read the article

  • How do I re-install Samba?

    - by Sheldon
    I recently followed a guide to configure Samba but I couldn't get it configured properly. After realizing that the guide was six years out of date I thought I should start again. I reinstalled samba by first using these commands: sudo apt-get purge samba sudo apt-get install samba But after reading my configuration file (/etc/samba/smb.conf) I noticed that it was the same file, containing the same edits I had made. I then proceeded to delete the directory and then re-install samba again. However, the directory is not replaced after re-instillation and now I don't appear to have a configuration file. How do I get it back? Or install Samba correctly?

    Read the article

  • Ubuntu 12.04 Network Manager: unable to save manual setting to set up a static ip

    - by Andy
    I am fairly familiar with setting up servers, and ubuntu is generally my flavor of choice, but I just installed 12.04 desktop and I am seeing some behavior in network manager that is really puzzling. The network connection works fine if I leave it set on dhcp, but I would like a static IP address for my new web server. When I go into network manager and edit the connection for the one and only NIC I can select MANUAL from the dropdown menu but as soon as I do the Save button becomes greyed out. Even after filling out all fields for the connection it is still grey and I am unable to save the static IP connection information. Any thoughts would be greatly appreciated. I'm hoping there is just some new setting that I am unaware of.... On another note, if I stop the network manager and go edit the interfaces file (and the appropriate hosts/routes/dns files), I do get a static ip address assigned and I can contact my server from the outside, however, the server cannot find the internet. Can't ping even its own ip... I can ping the loopback interface though. I'm really confused on this one. Hoping someone can offer some help.

    Read the article

  • audio and video data in RTP

    - by Banana
    Suppose a user wants to transmit both audio and video to another user, whose formats are AMR for audio and H.264 for video. Does the user have to transmit audio and video packets always separately? Meaning that it is not possible to mix audio and video within the same RTP packed, is that correct? If this is true I guess the RTP protocol will need to know the SSRC of both audio and video to be able to check the sync of the two streams.

    Read the article

  • Network print to brother MFC-7420

    - by trampster
    I am trying to pint to a Brother MFC-7420 from my ubuntu 10.04 machine. The brother is attached to a windows XP machine and is shared. This is what I have tried: System-Administration-Printing, Add, Expand Network Printer, Windows Printer via SAMBA, Browse (I can find the printer no problems here), Foward, Choose Driver Dialog, Brother, My printer is not in this list So the next thing I tried was to download the printer driver from here http://welcome.solutions.brother.com/bsc/public_s/id/linux/en/download_prn.html The driver installed fine but my printer still does not appear in the list. I also tried installing the cups wrapper but that gave the following error. Restarting Common Unix Printing System: cupsd [ OK ] cp: cannot stat `/usr/share/cups/model/MFC7420.ppd': No such file or directory dpkg: error processing cupswrappermfc7420 (--install): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: cupswrappermfc7420 I tried connecting the printer directly but even though I have installed the driver, when I go to printers and click on the printer (it shows up fine as a USB printer) then it say searching for drivers and then gives me a list, this is the same list as before which doesn't have my printer. It really shouldn't be this hard. on window you don't have to installing anything it just works and the same is true for my brothers Mac. How do I print to my printer?

    Read the article

< Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >