Search Results

Search found 26285 results on 1052 pages for 'grant back'.

Page 445/1052 | < Previous Page | 441 442 443 444 445 446 447 448 449 450 451 452  | Next Page >

• Troubleshooting unwanted NTP Traffic

  - by Jaxaeon

  A domain controller running Windows Server 2012 is sending NTP and NETBIOS traffic to an address that has never been configured as a time provider. The server logs give no indication that any NTP traffic is failing. The only place I see any evidence of this traffic is in pfSense system logs: (Blocked) Jun 9 08:48:50 DOMAIN 10.0.1.100:123 192.128.127.254:123 UDP (Blocked) Jun 9 08:48:53 DOMAIN 10.0.1.100:137 192.128.127.254:137 UDP As far as I can tell the NTP service is working normally otherwise: DC2.domain.com[10.0.1.101:123]: ICMP: 0ms delay NTP: -0.0131705s offset from DC1.domain.com RefID: DC1.domain.com [10.0.1.100] Stratum: 3 DC1.domain.com *** PDC ***[10.0.1.100:123]: ICMP: 0ms delay NTP: +0.0000000s offset from DC1.domain.com RefID: clock1.albyny.inoc.net [64.246.132.14] Stratum: 2 The time provider NtpClient is currently receiving valid time data from 1.pool.ntp.org,0×1 (ntp.m|0x0|0.0.0.0:123->204.2.134.163:123). The time provider NtpClient is currently receiving valid time data from 0.pool.ntp.org,0×1 (ntp.m|0x0|0.0.0.0:123->64.246.132.14:123). The time service is now synchronizing the system time with the time source 0.pool.ntp.org,0×1 (ntp.m|0x0|0.0.0.0:123->64.246.132.14:123). I've been inside and out of the NTP configuration and cannot find any reason for this traffic. Reverse DNS points the destination address to nothing.attdns.com. pinging nothing.attdns.com from the domain controller in question leads to a response from loopback (127.0.0.2) which makes my head hurt. Any ideas? EDIT1: It should probably be noted that after a dns flush, nslookup 192.128.127.254 returns nothing.attdns.com. 192.128.127.254 is not present in domain.com DNS records. The attdns.com domain is not present in cached lookups. 127.in-addr.arpa is clean of any funkyness. EDIT2: The loopback ping response from nothing.attdns.com is possibly unrelated. Machines on other networks are also displaying this behavior. EDIT3: As mentioned in the comments, I tracked the problem network adapter back to my pfSense VM hosted in esxi 5.5 (I know shame on me for virtualizing a firewall). pfSense was configured to use DC1.domain.com as its primary time provider, but upon changing it back to pool.ntp.org the problem persists. pfSense logs give no indication of NTP misconfiguration. Everywhere I can think to look this VM is identified as 10.0.1.253, so I still have no idea why it’s sending NTP requests as 192.128… Since this firewall was a temporary solution to a problem that no longer exists so I am going to decommission it. EDIT4: The queries were coming from another machine sharing the same virtual adapter as the firewall. The machine has two local adapters: one for LAN, and the other for attached hardware that uses an Ethernet connection. That hardware sits in the the mystery subnet, and the machine is broadcasting NTP requests over both adapters.

  Read the article

• How should I ask for help in getting my emails to stop bouncing?

  - by Gregg Williams

  For several months, people have been telling me that emails they sent to me have been bouncing back, marked as undeliverable. The bounce message would contain portions like this: Final-Recipient: rfc822;[email protected] Action: failed Status: 5.7.1 Diagnostic-Code: smtp;550 5.7.1 <[email protected]>... Recipient declines email from 69.64.159.2, <spamhaus-xbl>, Ref: http://www.spamhaus.org/query/bl?ip=69.64.159.2 Clicking the link on the last line, the destination page told me that "this IP address is infected with/emitting spamware/spamtrojan traffic and needs to be fixed." I could temporarily de-list this node by clicking a link on that page, but it would get back on the list and more emails to me to bounce. I own a domain, innerpaths.net, and I normally use [email protected] for my email. I have my domain registrar, namecheap.com, forward all email from innerpaths.net to the email account [email protected]. (BTW, I had this same problem at a former registrar. I changed registrars, hoping that would fix the problem. It didn't.) Trying to isolate the problem, I asked namecheap.com what I should do. Their answer, though substantial, left me scratching my head: We have received feedback from our upstream provider which informed us that the mail server that you are trying to email subscribes to a 3rd party blacklist service which they appear to be listed on at the present time and is causing destination mail server to reject the messages. Being blocked with one of these services can happen to anyone for many reasons and is something that is beyond our control. 3rd party blacklist services require companies whose mail servers they have blacklisted, pay fees in order to be removed from their lists. As we cannot pay fees to blacklist services which require them for removal, you should contact your email provider and have them whitelist our mail server IP address: 69.64.157.73. My best guess is that I should email my ISP, sonic.net, tell them what is going on and ask them to whitelist the IP address 69.64.157.73. (If not, please let me know.) But I want to know what is going on and how email works. I understand that there's a device at location 69.64.159.2 that is doing something bad that causes the "destination mail server [sonic.net's, I assume --gw] to reject the messages." I know that email is sent through multiple devices in a way that eventually gets it to its destination. Beyond that, here are my questions: 1) I thought the Internet "routed around damage." Why does email starting at namecheap.com always (or is it 'sometimes'?) go through 69.64.159.2? 2) Who is the "upstream provider" that the namecheap.com representative mentions, and what is their role? 3) How does having sonic.net's whitelisting namecheap.com's mail server prevent my email being bounced by 69.64.159.2? I've searched the Internet for answers but have found nothing useful. Thanks for whatever answers you can provide.

  Read the article

• Unmountable boot volume blue screen, what should I do?

  - by Josh

  I was trying to install an update from NVIDIA for my GTX 560, but while it was installing, my computer shut off. After a few minutes, I turned it back on. It got to the Windows boot screen and then had a blue screen error and if left on it would just keep doing that. A few details about my PC: I haven't added any new hardware or software, I'm running Windows XP Professional 32 bit and Windows XP Professional 64 bit on the same hard drive for about 2 years now. I have 2 other hard drives also, but I don't have one large enough to hold everything from my main hard drive, so formatting isn't an option. Now, as for what I've done so far: I've scanned the RAM with "memtest - 86 v3.4" and it said that it was good. I scanned the hard drive in question with chkdsk /r and it gets to 50% and tells me something along the lines of "the drive has one or more unrepairable problems". I also tried to use chkdsk on the drive I installed the new copy of Windows XP on and it got to 75% then jumped back down to 50% and stayed there (I had to reboot the pc). So, after that, I turned off auto reboot and got to read the blue screen error code and I looked it up only to find that nobody seems to have this problem, just problems close to it. The error code is 0x000000ed and I've seen a lot of these online but none that matched the detailed part of the code UNMOUNTABLE_BOOT_VOLUME 0x000000ed (0xfffffadf513c19a0, 0xffffffffc0000006, 0, 0) So, I have installed another copy of Windows XP Professional 32 bit on one of my other hard drives in hopes of accessing the data on the drive in question and when it booted it asked if I wanted chkdsk to scan the drive in question and this is what it found: file record segments 12740, 12741, 12742 and 12743 were reported unreadable. Then it says "recovering lost files" but it sits there for a few seconds and then just boots to Windows. I can't access the drive in question from Windows as far as I can tell, it just says "drive not accessible" and when I go to properties it says that the drive has 100% free space. So, after that failed I didn't give up, I looked for another way to access the drive in question. I used a Ubuntu bootable disk and was able to access the drive in question without any problems. However, I can't access the registry editor because it's a .exe file and that won't load from Ubuntu. I made a copy of the "Windows" folder and put it on one of my other drives and that's where I'm stuck at now. I'm sure my drive works fine, I know chkdsk can't fix the problem with it and I know what caused the problem in the first place for the most part, but I don't know what to do about it. I have a laptop that I can use to download and burn disks if needed and I also have the other copy of Windows XP Professional 32 bit that I can use that's installed on the computer in question (so I know it's not a hardware issue). I'm pretty sure it's a driver issue or the update was editing the registry when it shut off and left me when a broken registry. I've tried accessing C:\Windows\System32\CONFIG only to find that the Windows XP disk repair option can't even access the files on the drive in question. It seems I'll need to be able to do everything from Ubuntu unless there is something I haven't tried with the Windows XP disk. I didn't install the update on Windows XP 64 bit but yet it also has the same blue screen error (that's where the error code above came from but I haven't checked to see if they are the same). They both stopped working at the same time, so I assume it's one problem causing both to not work.

  Read the article

• How to diagnose computer lockup/freezing problem

  - by Scott Mitchell

  I built a desktop computer a couple years back with the following specs: CPU: Intel Core 2 Quad Q9300 Yorkfield 2.5GHz 6MB L2 Cache LGA 775 95W Quad-Core Processor BX80580Q9300 Motherboard: EVGA 122-CK-NF68-T1 LGA 775 NVIDIA nForce 680i SLI ATX Intel Motherboard Video Card: Two EVGA 256-P2-N758-TR GeForce 8600GT SCC 256MB 128-bit GDDR3 PCI Express x16 SLI Supported Video Card PSU: SeaSonic S12 Energy Plus SS-550HT 550W ATX12V V2.3 / EPS12V V2.91 SLI Certified CrossFire Ready 80 PLUS Certified Active PFC Power Supply Memory: Two G.SKILL 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Dual Channel Kit Desktop Memory Model F2-6400CL5D-4GBPQ Since its inception, the machine has periodically locked up, the regularlity having varied over the years from once a day to once a month. Typically, lockups happen once every few days. By "lockup" I mean my computer just freezes. The screen locks up, I can't move the mouse. Hitting keys on my keyboard that normally turn LEDs on or off on the keyboard (such as Caps Lock) no longer turn the LEDs on or off. If there was music playing at the time of the lockup, noise keeps coming out of the speakers, but it's just the current frequency/note that plays indefinitely. There is no BSOD. When such a lockup occurs I have to do a hard reboot by either turning off the computer or hitting the reset button. I have the most recent version of the NVIDIA hardware drivers, and update them semi-regularly, but that hasn't seemed to help. I am currently using Windows 7 x64, but was previously using Windows Server 2003 x64 and having the same lockup issues. My guess is that it's somehow video driver or motherboard related, but I don't know how to go about diagnosing this problem to narrow down which of the two is the culprit. Additional information re: cooling Regarding cooling... I've not installed any after-market cooling systems aside from two regular fans I scavenged from an older computer. The fan atop the CPU is the one that shipped with it. One of the two scavenged fans I added it located at the bottom tower of the corner, in an attempt to create some airflow from front to back. The second fan is pointed directly at the two video cards. SpeedFan installation and readings Per studiohack's suggestion, I installed SpeedFan, which provided the following temperature readings: GPU: 63C GPU: 65C System: 76C CPU: 64C AUX: 36C Core 0: 78C Core 1: 76C Core 2: 79C Core 3: 79C Update #3: Another Lockup :-( Well, I had another lockup last night. :-( SpeedFan reported the CPU temp at 38 C when it happened, and there was no spike in temperature leading up to the freeze. One thing I notice is that the freeze seems more likely to happen if I am watching a video. In fact, of the last 5 freezes over the past month, 4 of them have been while watching a video on Flickr. Not necessarily the same video, but a video nevertheless. I don't know if this is just coincidence or if it means anything. (As an aside, each night before bedtime my 2 year old daughter sits on my lap and watches some home videos on Flickr and, in the last month, has learned the phrase, "Uh oh, computer broke.") Update #4: MemTest86 and 3DMark06 Test Results: Per suggestions in the comments, I ran the MemTest86 overnight and it cycled through the 8 GB of memory 5 times without error. I also ran the 3DMark06 test without a problem (see my scores at http://3dmark.com/3dm06/15163549). So... what now? :-) Any further suggestions on what to check? Is there some way to get a stack trace or something when the computer locks like that? Thanks

  Read the article

• mysql replication 1x master, 1x slave

  - by clarkk

  I have just setup one master and one slave server, but its not working.. On my website I connect to the slave server and I insert some rows, but they do not appear on the master and vice versa.. What is wrong? This is what I did: Master: -> /etc/mysql/my.cnf [mysqld] log-bin = mysql-master-bin server-id=1 # bind-address = 127.0.0.1 binlog-do-db = test_db Slave: -> /etc/mysql/my.cnf [mysqld] log-bin = mysql-slave-bin server-id=2 # bind-address = 127.0.0.1 replicate-do-db = test_db Slave: terminal 0 > mysql> STOP SLAVE; // and drop tables Master: terminal 1 > mysql> CREATE USER 'repl_slave'@'slave_ip' IDENTIFIED BY 'repl_pass'; mysql> GRANT REPLICATION SLAVE ON *.* TO 'repl_slave'@'slave_ip'; mysql> FLUSH PRIVILEGES; mysql> FLUSH TABLES WITH READ LOCK; -- leave terminal open terminal 2 > shell> mysqldump -u root -pPASSWORD test_db --lock-all-tables > dump.sql mysql> SHOW MASTER STATUS; Slave: terminal 3 > shell> mysql -u root -pPASSWORD test_db < dump.sql terminal 0 > mysql> CHANGE MASTER TO mysql> MASTER_HOST='master_ip', mysql> MASTER_USER='repl_slave', mysql> MASTER_PASSWORD='repl_pass', mysql> MASTER_PORT=3306, mysql> MASTER_LOG_FILE='mysql-master-bin.000003', // terminal 2 > SHOW MASTER STATUS mysql> MASTER_LOG_POS=4, // terminal 2 > SHOW MASTER STATUS mysql> MASTER_CONNECT_RETRY=10; mysql> START SLAVE; mysql> SHOW SLAVE STATUS; Here is the slave status: Array ( [Slave_IO_State] => Waiting for master to send event [Master_Host] => xx.xx.xx.xx [Master_User] => repl_slave [Master_Port] => 3306 [Connect_Retry] => 10 [Master_Log_File] => mysql-master-bin.000003 [Read_Master_Log_Pos] => 106 [Relay_Log_File] => mysqld-relay-bin.000002 [Relay_Log_Pos] => 258 [Relay_Master_Log_File] => mysql-master-bin.000003 [Slave_IO_Running] => Yes [Slave_SQL_Running] => Yes [Replicate_Do_DB] => test_db [Replicate_Ignore_DB] => [Replicate_Do_Table] => [Replicate_Ignore_Table] => [Replicate_Wild_Do_Table] => [Replicate_Wild_Ignore_Table] => [Last_Errno] => 0 [Last_Error] => [Skip_Counter] => 0 [Exec_Master_Log_Pos] => 106 [Relay_Log_Space] => 414 [Until_Condition] => None [Until_Log_File] => [Until_Log_Pos] => 0 [Master_SSL_Allowed] => No [Master_SSL_CA_File] => [Master_SSL_CA_Path] => [Master_SSL_Cert] => [Master_SSL_Cipher] => [Master_SSL_Key] => [Seconds_Behind_Master] => 0 [Master_SSL_Verify_Server_Cert] => No [Last_IO_Errno] => 0 [Last_IO_Error] => [Last_SQL_Errno] => 0 [Last_SQL_Error] => )

  Read the article

• How to prevent delays associated with IPv6 AAAA records?

  - by Nic

  Our Windows servers are registering IPv6 AAAA records with our Windows DNS servers. However, we don't have IPv6 routing enabled on our network, so this frequently causes stall behaviours. Microsoft RDP is the worst offender. When connecting to a server that has a AAAA record in DNS, the remote desktop client will try IPv6 first, and won't fall back to IPv4 until the connection times out. Power users can work around this by connecting to the IP address directly. Resolving the IPv4 address with ping -4 hostname.foo always works instantly. What can I do to avoid this delay? Disable IPv6 on client? Nope, Microsoft says IPv6 is a mandatory part of the Windows operating system. Too many clients to ensure this is set everywhere consistently. Will cause more problems later when we finally implement IPv6. Disable IPv6 on the server? Nope, Microsoft says IPv6 is a mandatory part of the Windows operating system. Requires an inconvenient registry hack to disable the entire IPv6 stack. Ensuring this is correctly set on all servers is inconvenient. Will cause more problems later when we finally implement IPv6. Mask IPv6 records on the user-facnig DNS recursor? Nope, we're using NLNet Unbound and it doesn't support that. Prevent registration of IPv6 AAAA records on the Microsoft DNS server? I don't think that's even possible. At this point, I'm considering writing a script that purges all AAAA records from our DNS zones. Please, help me find a better way. UPDATE: DNS resolution is not the problem. As @joeqwerty points out in his answer, the DNS records are returned instantly. Both A and AAAA records are immediately available. The problem is that some clients (mstsc.exe) will preferentially attempt a connection over IPv6, and take a while to fall back to IPv4. This seems like a routing problem. The ping command produces a "General failure" error message because the destination address is unroutable. C:\Windows\system32>ping myhost.mydomain Pinging myhost.mydomain [2002:1234:1234::1234:1234] with 32 bytes of data: General failure. General failure. General failure. General failure. Ping statistics for 2002:1234:1234::1234:1234: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), I can't get a packet capture of this behaviour. Running this (failing) ping command does not produce any packets in Microsoft Network Monitor. Similarly, attempting a connection with mstsc.exe to a host with an AAAA record produces no traffic until it does a fallback to IPv4. UPDATE: Our hosts are all using publicly-routable IPv4 addresses. I think this problem might come down to a broken 6to4 configuration. 6to4 behaves differently on hosts with public IP addresses vs RFC1918 addresses. UPDATE: There is definitely something fishy with 6to4 on my network. When I disable 6to4 on the Windows client, connections resolve instantly. netsh int ipv6 6to4 set state disabled But as @joeqwerty says, this only masks the problem. I'm still trying to find out why IPv6 communication on our network is completely non-working.

  Read the article

• Postfix certificate verification failed for smtp.gmail.com

  - by Andi Unpam

  I have problem, my email server using postfix with gmail smtp, i use account google apps, but always ask for SASL authentication failed, I sent an email using php script, after I see the error logs in the wrong password, after I open the URL from the browser and no verification postfixnya captcha and could return, but after 2-3 days later happen like that again. This my config postfix #myorigin = /etc/mailname smtpd_banner = Hostingbitnet Mail Server biff = no append_dot_mydomain = no readme_directory = no myhostname = webmaster.hostingbitnet.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = localhost, webmaster.hostingbitnet.com, localhost.localdomain, 103.9.126.163 relayhost = [smtp.googlemail.com]:587 relay_transport = relay relay_destination_concurrency_limit = 1 mynetworks = 127.0.0.0/8, 192.168.0.0/16, 172.16.0.0/16, 10.0.0.0/8, 103.9.126.0/24 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all default_transport = smtp relayhost = [smtp.gmail.com]:587 smtp_sasl_auth_enable = yes smtp_sasl_password_maps = hash:/etc/postfix/google-apps smtp_sasl_security_options = noanonymous smtp_use_tls = yes smtp_sender_dependent_authentication = yes tls_random_source = dev:/dev/urandom default_destination_concurrency_limit = 1 smtp_tls_CAfile = /etc/postfix/tls/root.crt smtp_tls_cert_file = /etc/postfix/tls/cert.pem smtp_tls_key_file = /etc/postfix/tls/privatekey.pem smtp_tls_session_cache_database = btree:$data_directory/smtp_tls_session_cache smtp_tls_security_level = may smtp_tls_loglevel = 1 smtpd_tls_CAfile = /etc/postfix/tls/root.crt smtpd_tls_cert_file = /etc/postfix/tls/cert.pem smtpd_tls_key_file = /etc/postfix/tls/privatekey.pem smtpd_tls_session_cache_database = btree:$data_directory/smtpd_tls_session_cache smtpd_tls_security_level = may smtpd_tls_loglevel = 1 #secure smtpd_recipient_restrictions = permit_mynetworks,permit_sasl_authenticated,check_client_access hash:/var/lib/pop-before-smtp/hosts,reject_unauth_destination Log from mail.log Oct 30 14:51:13 webmaster postfix/smtp[9506]: Untrusted TLS connection established to smtp.gmail.com[74.125.25.109]:587: TLSv1 with cipher RC4-SHA (128/128 bits) Oct 30 14:51:15 webmaster postfix/smtp[9506]: 87E2739400B1: SASL authentication failed; server smtp.gmail.com[74.125.25.109] said: 535-5.7.1 Please log in with your web browser and then try again. Learn more at?535 5.7.1 https://support.google.com/mail/bin/answer.py?answer=78754 ix9sm156630pbc.7 Oct 30 14:51:15 webmaster postfix/smtp[9506]: setting up TLS connection to smtp.gmail.com[74.125.25.108]:587 Oct 30 14:51:15 webmaster postfix/smtp[9506]: certificate verification failed for smtp.gmail.com[74.125.25.108]:587: untrusted issuer /C=US/O=Equifax/OU=Equifax Secure Certificate Authority Oct 30 14:51:16 webmaster postfix/smtp[9506]: Untrusted TLS connection established to smtp.gmail.com[74.125.25.108]:587: TLSv1 with cipher RC4-SHA (128/128 bits) Oct 30 14:51:17 webmaster postfix/smtp[9506]: 87E2739400B1: to=<[email protected]>, relay=smtp.gmail.com[74.125.25.108]:587, delay=972, delays=967/0.03/5.5/0, dsn=4.7.1, status=deferred (SASL authentication failed; server smtp.gmail.com[74.125.25.108] said: 535-5.7.1 Please log in with your web browser and then try again. Learn more at?535 5.7.1 https://support.google.com/mail/bin/answer.py?answer=78754 s1sm3850paz.0) Oct 30 14:51:17 webmaster postfix/error[9508]: B3960394009D: to=<[email protected]>, orig_to=<root>, relay=none, delay=29992, delays=29986/5.6/0/0.07, dsn=4.7.1, status=deferred (delivery temporarily suspended: SASL authentication failed; server smtp.gmail.com[74.125.25.108] said: 535-5.7.1 Please log in with your web browser and then try again. Learn more at?535 5.7.1 https://support.google.com/mail/bin/answer.py?answer=78754 s1sm3850paz.0) BTW I made cert follow the link here http://koti.kapsi.fi/ptk/postfix/postfix-tls-cacert.shtml and it worked, but after 2/3 days my email back to problem invalid SASL, and then i'm required to log in use a browser and enter the captcha there but success log in after input captcha, and my email server can send emails from telnet or php script. but it will be back in trouble after 2/3days later. My question is how to make it permanent certificate? Thanks n greeting.

  Read the article

• DNS lookups failing somewhere between firewall and router

  - by TessellatingHeckler

  we have a setup of ADSL line - Cisco 837 ADSL router - Zyxel ZyWall 35 firewall/NAT - Switch == Intel load balanced NICS in a server. It has been fine for years, suddenly DNS resolution stopped working on the server. No changes that I know of, so I can't work backwards from there. It was configured with the ISP's DNS servers, neither network device does DNS relaying. Wireshark shows the request go out but nothing comes back. The server networking stack seems OK though, because if we query an internal DNS server on a remote site, that works. I can logon to the Cisco, and DNS resolves OK from the command line. I can logon to the ZyWall, and DNS does not resolve from the command line. So the problem seems to be the firewall, patch cable or router, yes? On the router: interface Ethernet0 ip address aaa.bbb.ccc.ddd 255.255.255.ddd ip tcp adjust-mss 1450 hold-queue 100 out On the firewall: DNS server set to 8.8.8.8 (Google's), DNS traffic allowed LAN-WAN. What else should I look for? Update: Following This guide I've got traffic logging on the Cisco. I have also got access to a public DNS server which I can run tcpdump on to see things from the other side. And as per the below comments, I've tested with Dig and see that DNS over TCP works, and over UDP does not. Currently: DNS request from the server using TCP shows up in the firewall log, and in the Cisco log, and in tcpdump on the DNS server, the answer comes back, it works fine. DNS request from the server using UDP shows up in the firewall log, and in the Cisco log, does NOT show in tcpdump on the DNS server, times out. DNS request from the cisco (using UDP) does show up in tcpdump on the DNS server, answer received, works fine. Ping requests from the server and the cisco to the DNS server show up in tcpdump on the DNS server. DNS request from the server using UDP does show up on the firewall. Summary: TCP seems fine throughought. UDP works over the ADSL and to the Cisco, and it works from the server to the Cisco, but it doesn't cross the Cisco properly, it seems. I did see the Cisco showing as connected at 10Mb/full-duplex internally, and the firewall showing as 100Mb/full-duplex externally. I have forced the firewall to 10Mb and rebooted both devices. That seemed to help get UDP traffic (server-firewall-cisco) instead of (server-firewall), but did not fix it. Update: Sanitized Cisco config: version 12.2 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname cisco ! logging queue-limit 100 enable secret 5 {password} enable password 7 {password} ! ip subnet-zero ip domain name example.org ip name-server {nameserver_IP} ! ! ip audit notify log ip audit po max-events 100 no ftp-server write-enable ! interface Ethernet0 ip address {Inside_public_IP} 255.255.255.248 ip tcp adjust-mss 1460 hold-queue 100 out ! interface ATM0 no ip address no atm ilmi-keepalive pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 ! dsl operating-mode auto ! interface Dialer1 ip unnumbered Ethernet0 encapsulation ppp dialer pool 1 dialer idle-timeout 0 dialer persistent no cdp enable ppp chap hostname {ADSL_Username} ppp chap password 7 {ADSL_Password} ! ip classless ip route 0.0.0.0 0.0.0.0 Dialer1 no ip http server no ip http secure-server ! access-list 23 permit {IP} dialer-list 1 protocol ip permit no cdp run snmp-server enable traps tty ! {con, vty} end

  Read the article

• Debian Lenny to Debian Squeeze upgrade problems

  - by Roland Soós

  Hi! Yesterday I made a dist-upgrade on my Debian Lenny server. I thought it will be easy as an usual upgrade, but it's not. I got a lot of problem after the update: # apt-get upgrade Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt-get -f install' to correct these. The following packages have unmet dependencies: linux-image-2.6-amd64 : Depends: linux-image-2.6.32-5-amd64 but it is not installed E: Unmet dependencies. Try using -f. Then I tried the suggestion: # apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following packages were automatically installed and are no longer required: libio-compress-base-perl libatk1.0-0 libts-0.0-0 libmime-types-perl libc-client2007b libgtk2.0-common libxfixes3 libgsf-1-common hicolor-icon-theme libfile-remove-perl libxcomposite1 libltdl3-dev libneon27 libmd5-perl libwmf0.2-7 libilmbase6 libatk1.0-data djvulibre-desktop libdirectfb-1.0-0 fam libxinerama1 libcroco3 libopenexr6 libgsf-1-114 libmail-box-perl libdjvulibre21 openssl-blacklist librsvg2-2 libio-compress-zlib-perl libsysfs2 libbeecrypt6 libxdamage1 libobject-realize-later-perl libuser-identity-perl libgtk2.0-bin libxi6 libxcursor1 portmap libxrandr2 libgtk2.0-0 Use 'apt-get autoremove' to remove them. The following extra packages will be installed: linux-image-2.6.32-5-amd64 Suggested packages: linux-doc-2.6.32 The following NEW packages will be installed: linux-image-2.6.32-5-amd64 0 upgraded, 1 newly installed, 0 to remove and 121 not upgraded. 98 not fully installed or removed. Need to get 0 B/28.6 MB of archives. After this operation, 103 MB of additional disk space will be used. Do you want to continue [Y/n]? y perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "hu_HU.UTF-8" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: Nincs ilyen f?jl vagy k?nyvt?r Preconfiguring packages ... (Reading database ... 37915 files and directories currently installed.) Unpacking linux-image-2.6.32-5-amd64 (from .../linux-image-2.6.32-5-amd64_2.6.32-30_amd64.deb) ... locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: Nincs ilyen f?jl vagy k?nyvt?r dpkg: error processing /var/cache/apt/archives/linux-image-2.6.32-5-amd64_2.6.32-30_amd64.deb (--unpack): failed in write on buffer copy for backend dpkg-deb during `./lib/modules/2.6.32-5-amd64/kernel/sound/pci/hda/snd-hda-codec-realtek.ko': No space left on device configured to not write apport reports dpkg-deb: subprocess paste killed by signal (Broken pipe) locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: Nincs ilyen f?jl vagy k?nyvt?r Running postrm hook script /sbin/update-grub. Searching for GRUB installation directory ... found: /boot/grub Searching for default file ... found: /boot/grub/default Testing for an existing GRUB menu.lst file ... found: /boot/grub/menu.lst Searching for splash image ... none found, skipping ... Found kernel: /boot/vmlinuz-2.6.26-2-amd64 Updating /boot/grub/menu.lst ... done Examining /etc/kernel/postrm.d . run-parts: executing /etc/kernel/postrm.d/initramfs-tools 2.6.32-5-amd64 /boot/vmlinuz-2.6.32-5-amd64 Errors were encountered while processing: /var/cache/apt/archives/linux-image-2.6.32-5-amd64_2.6.32-30_amd64.deb E: Sub-process /usr/bin/dpkg returned an error code (1) # dpkg-reconfigure locales perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "hu_HU.UTF-8" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: Nincs ilyen f?jl vagy k?nyvt?r /usr/sbin/dpkg-reconfigure: locales is broken or not fully installed Then I stucked. Do you have any idea how could I solve this?

  Read the article

• Ubuntu 12 crashed and took down network

  - by Leopd

  We recently set up a new Ubuntu 12.04LTS server on our network. It's not fully configured so it's not doing much beyond sshd and a default apache2 install. But this evening it appears to have crashed. It wasn't responding to the network or the keyboard. But the worst part is, it took down the entire network. My knowledge of the network stack below OSI layer 3 is very limited, so the rest confuses me. When this machine was physically connected to the network, no other machine could connect to the outside internet. When things were broken, running arp showed that our gateway's IP address (10.0.1.1) was listed as "invalid." Unplugging the server from the network fixed the problem, and plugging it back in broke it again. So the crashed server was advertising itself as owning the gateway's IP address? There's nothing at all in syslog during the time when it was causing problems. Any ideas about how to figure out what went wrong or what we can do to prevent it from happening again? I'm hesitant to even put the machine back on the network right now. Update ** It crashed again, and I ran tcpdump -penn arp (thanks bahamat!) for several minutes and got this... (timestamps and duplicate lines removed) 00:1e:65:f8:dc:24 > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 60: Request who-has 10.0.1.1 tell 10.0.2.191, length 46 00:1e:65:f8:dc:24 > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 60: Request who-has 10.0.1.44 tell 10.0.2.191, length 46 60:d8:19:d4:71:d6 > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 60: Request who-has 10.0.1.1 tell 10.0.2.125, length 46 d4:9a:20:04:e9:78 > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 42: Request who-has 192.168.1.1 tell 192.168.1.100, length 28 Update 2 ** When the network is functioning properly, arping -c4 10.0.1.1 returns this: ARPING 10.0.1.1 60 bytes from c0:c1:c0:77:25:8e (10.0.1.1): index=0 time=267.982 usec 60 bytes from c0:c1:c0:77:25:8e (10.0.1.1): index=1 time=422.955 usec 60 bytes from c0:c1:c0:77:25:8e (10.0.1.1): index=2 time=299.215 usec 60 bytes from c0:c1:c0:77:25:8e (10.0.1.1): index=3 time=366.926 usec --- 10.0.1.1 statistics --- 4 packets transmitted, 4 packets received, 0% unanswered (0 extra) When the bad server is plugged in, arping -c4 10.0.1.1 returns: ARPING 10.0.1.1 --- 10.0.1.1 statistics --- 4 packets transmitted, 0 packets received, 100% unanswered (0 extra) Context ** 10.0.x.x is the main subnet. 10.0.1.1 is the main internet gateway 10.0.1.44 is a printer 10.0.2.* devices are all laptops / workstations I have no idea what's using the 192.168.x.x subnet -- your guesses are at least as good as mine. A VM on a workstation? A misconfigured WAP? Somebody re-sharing wifi? A machine that failed to DHCP? The offending ubuntu server's MAC address ends in cd:80 so isn't listed in the dump. It should DHCP to 10.0.3.3 Thanks for any help. This ARP stuff is all voodoo to me. Packets just go to IP addresses, right? ;)

  Read the article

• Issues with Verizon's "Network Extender" device talking on my home network.

  - by Logan

  I recently switched my phone service to Verizon from ATT, and I get somewhat spotty service in my house. I called them and they sent me a "network extender" device for free. Its a femtocell that connects to my home network. The directions that come with it are very dumbed down, basically just say to connect it to your router and put it near a window (so it can get a GPS signal, it has to make sure its within the correct area before operating). The problem I'm having is the network light on it stays red. The troubleshooting information that came with it tells me this means there is a bad network connection. Its connected through an ASUS router running DD-WRT. No other devices on my network have a problem with it, including a Western Digital WDLIVE device, mine and my wife's cell phones (via wifi), a Wii, and an Xbox. If I connect the device directly to my cable modem, the light goes blue (which means good) and it starts working. So this tells me that its definately a configuration issue with my router. Verizon basically washed their hands of me when I connected it to my cable modem, and told me that its a router issue and to try a different router. Because normal people just have extra routers laying around their houses... When I connect it to the router, I can watch the DHCP Clients list on the status page, and the MAC of the network extender quickly fills up the clients list, grabbing every available DHCP address. Its like it grabs an address, can't connect to the internet, releases it, grabs another, then another, then another. So in the DHCP server settings I assigned a static IP to its MAC. This made it quit doing what it was doing before, but its still not working. I found the ports I needed to open on verizon's website, and opened them in the port forwarding config on my router. This still didn't help. So, I tried setting the network extender device's IP as the DMZ IP on the router. This still did no good. I called Verizon back and got the tech to write up a report which he passed on to a "senior network tech" who I got a call back from a few hours ago. This guy told me that while an ASUS router isn't listed as a supported device, he's not really sure why its not working. He suggested restoring the firmware to stock ASUS firmware and trying again. I have a very hard time believing its DD-WRT doing this, since every other device is working just fine with it. But its also not the Network Extender, since it works just fine when connected directly to the modem. At this point I'm out of ideas, and the next step is to restore the stock firmware on my router, and then going to walmart and getting a linksys WRT-54G to try. Is there anything else I could try before going that drastic? Cliffs- -Network extender won't work behind router, works when connected directly to cable modem. -Extender goes nuts when allowed to pick its own DHCP address, I had to assign it a static IP. -Won't work when correct ports are forwarded to it -Won't work with a DMZ address.

  Read the article

• can't login to new install of SQL 2008 x64 via SSMS

  - by tpcolson

  I have performed a fresh install of SQL 2008 x64 on a fresh install of Server 2008 R2 x64 in an AD environment. Upon install completion, I cannot login to the SQL Instance via SSMS, with the following error: Login failed for user domain\user. Reason: Token-based server access validation failed with an infrastructure error. Check for previous errors. [CLIENT: ]. Background: the server is correctly joined to the AD Domain, the install was performed with defaults, windows authentication only (per organizational rules), the SQL install completes with no errors, domain\user was added as SQL Amin during setup account provisioning, I am logged into to console as domain\user when this error occurs, windows firewall is OFF, UAC is ON (an will never be turned off in accordance with organizational policy). To troubleshoot this error I have tried: Run SSMS as administrator: fail; Start SQL in single user mode, run SSMS: fail Start SQL in single user mode, run SSMS as administrator: Success Start SQL in single user mode, run SSMS as administrator, remove domain\user from sysadmin group, re-add, run SSMS: fail; Any combination and permutation of log off and log on, reboot, and chant gregorian prayers: fail; Reimage server with 2008 x64, slipstream SP2 into SQL 2008 install, all above troubleshooting steps are repeatable exactly, so I've narrowed this down to not being a SP issue; (this is NOT 2008 SQL R2) Any suggestion on how to grant management access to this fresh install of SQL 2008 via SSMS? Our organizational policy is no console access to servers, management will be done via management tools intalled on client workstations. domain\user is a group of 8 users whom will have SSMS installed on workstations. However, we can't even access SQL via SSMS from the console! We cannot deploy this in an environment where these 8 users will have to sneak into the server closet on the weekends and have console access to SQL and run SSMS as administrator. EDIT: domain\group is a replacement for the actual object; the queries indicate that domain\group does indeed have the right privelges....!?! 1> EXEC xp_logininfo 'domain\group' go account name type privilege mapped login name permission path 'domain\group' group admin 'domain\group' NULL xp_logininfo seems to show 'domain\group' in the sql admin group; 1> SELECT A.name AS 'Role', B.name AS 'Login' 3> FROM sys.server_role_members C 5> INNER JOIN sys.server_principals A ON A.principal_id = C.role_principal_id 7> INNER JOIN sys.server_principals B ON B.principal_id = C.member_principal _id 9> go Role Login sysadmin sa sysadmin NT AUTHORITY\SYSTEM sysadmin NT SERVICE\MSSQLSERVER sysadmin NT SERVICE\SQLSERVERAGENT sysadmin domain\group 1> SELECT PRINCIPAL_ID AS [Principal ID], 2> NAME AS [User], 3> TYPE_DESC AS [Type Description], 4> IS_DISABLED AS [Status] 5> FROM sys.server_principals 6> GO Principal ID User Type Description Status ------------ ------------------------------------------------------------------- ------------------------------------------------------------- ------------------ ------------------------------------------ ------ 1 sa SQL_LOGIN 1 2 public SERVER_ROLE 0 3 sysadmin SERVER_ROLE 0 4 securityadmin SERVER_ROLE 0 5 serveradmin SERVER_ROLE 0 6 setupadmin SERVER_ROLE 0 7 processadmin SERVER_ROLE 0 8 diskadmin SERVER_ROLE 0 9 dbcreator SERVER_ROLE 0 10 bulkadmin SERVER_ROLE 0 101 ##MS_SQLResourceSigningCertificate## CERTIFICATE_MAPPED _LOGIN 0 102 ##MS_SQLReplicationSigningCertificate## CERTIFICATE_MAPPED _LOGIN 0 103 ##MS_SQLAuthenticatorCertificate## CERTIFICATE_MAPPED _LOGIN 0 105 ##MS_PolicySigningCertificate## CERTIFICATE_MAPPED _LOGIN 0 257 ##MS_PolicyTsqlExecutionLogin## SQL_LOGIN 1 259 NT AUTHORITY\SYSTEM WINDOWS_LOGIN 0 260 NT SERVICE\MSSQLSERVER WINDOWS_GROUP 0 262 NT SERVICE\SQLSERVERAGENT WINDOWS_GROUP 0 263 ##MS_PolicyEventProcessingLogin## SQL_LOGIN 1 264 ##MS_AgentSigningCertificate## CERTIFICATE_MAPPED _LOGIN 0 265 domain\group WINDOWS_GROUP 0 (21 rows affected)

  Read the article

• Intel Rapid Storage / Smart Response SSD caching issue

  - by goober

  Background Recently built my own PC. It works! Almost. It's been a while since getting into the guts of these things, so I'm familiar but may be missing something simple. FYI, I don't care about blowing the OS away -- it's brand new and we can go back from scratch as many times as necessary. Goal / Issue I'd like to use the SSD to take advantage of Intel's Smart Response technology (allows the SSD to act as a cache for HDDs) I would like the SSD cache to act as a cache for my HDDs, which I would like to be in a RAID1 array (so I get the speed from the SSD and the redundancy from the RAID1) However, Windows only sees the drive in device manager (not as a drive), so I'm unsure what to do about that. Related: as far as I know, for this to work, the drives all have to be in a single RAID array (i.e. a RAID0 pairing of the SSD and the RAID1 HDD array). However, when attempting this at the BIOS level, I am told there is not enough space for an array. Steps so Far Moved the SSD onto the Intel controller (I'd had it on the Marvel 6.0 controller instead of the Intel controller, so the BIOS was only seeing it in a strange way) Updated the BIOS of the motherboard to the latest version Reinstalled Intel's RST (iRST?) software several times, as some forums reported it working after reinstalling 3 times (which does not inspire confidence). Checked Intel storage: it does see the SSD as a physical, non-RAID device. However, it says no space exists if I try to create an array. Checked the BIOS: it does not show up in the boot order, but is an option that can be selected under boot options. Tried the firmware update for that model. Issue: the firmware CD doesn't detect a drive; maybe the Intel storage controller is making it difficult? moved the ssd to the marvel controller. The firmware update cd appeared to hang while searching for drives. swapped out the SATA cable for the manufacturer's and moved back to the intel storage controller. Noticed at this point that in the Intel RST software, a device DOES show up in addition to the RAID set -- only shown as a "60 GB internal disk". Windows doesn't appear to see it as a drive, but it does still show in device manager. Move SSD to port from 0-3 on MOBO and set SATA mode to IDE (after disconnecting RAID1 config) to allow the firmware update to work. Firmware was already at the latest version. Next Steps ? Components involved ASUS P8Z68-V PRO motherboard (Intel Z68 Chipset) Intel i7 2600k Processor 2 x 1TB 7200 RPM HDDs 64 GB Crucial M4 SSD (M4-CT064M4SSD2) For Reference -- Storage Configuration Intel 3 gbps Intel 3gbps Intel 6gbps Marvel 6gbps +----------+ +----------+ +----------+ +----------+ | | <----+ | | +-+ | | | |----------| | |----------| |-|--------| |----------| | | | | + | | | | | | +----------+ | +--|-------+ +-|--------+ +----------+ | | | + v v | 1 TB HDD 64 GB SSD + +> 1 TB HDD For Reference -- Intel RST (v10.8.0.1003) Screenshot Don't mind the "rebuilding" -- knocked a power cable out at one point; it's doing its job, not an indicator of a bad HDD. Any thoughts? Thanks in advance for any help!

  Read the article

• IBM Server Config questions

  - by Joel Coel

  I have a few questions on a potential server setup. First, the situation: Last year we bought an IBM x3500 server with 2 Xeon E5410's, 9GB RAM, 6 HDDs. The original intent for this server was to replace the old exchange e-mail server. It was brought in, set up, and then shortly after we switched to gmail. Shortly after that my predecessor left for greener pastures, and finally I was hired. So this nice server is now sitting (mostly) idle. This year I have budget again for one server, and of course I want to put this other server to work. I'm thinking about the best use for the two server, and I think I finally have a plan for what I want to do with them. The idea is to use the two newer servers as a pair of VM hosts. I will set up each server with the same 8 VMs, but divide up the load so that only 4 are active per physical host. That means I've normally got 2GB RAM + 2 cores per host. I've done some load testing to pick out what servers to convert to virtual, and chose them so that each host will be capable of handling the entire set of 8 by itself in a pinch with 1 core and 1GB RAM, but would be very taxed to do so. This should take our data center from 13 total servers down to 7. The "servers" I'm replacing are mostly re-purposed desktops, so I'm more than happy to be able to do this. Now it's time to go shopping for the new server. I'd like my two hosts to match as closely as possible, and so I'm looking at IBM again. It also helps that we have some educational matching grant money from IBM that I need to use to help pay for this system (we're a small private college). So finally, (if you're not bored already), we come to my questions: Am I missing anything big or obvious in this plan? I'm a little worried about network performance since the VM hosts will only have 4 nics total where 8 used to be, but I don't think it will be a problem. Is there anything else like this I might be overlooking? Am I making it even too complicated? IBM no longer has a good analog to last year's server. If I want to match the performance (8 cores, 9GB RAM, 1333mhz front side bus, 6 spindles), I have to spend quite a bit more than we paid last year: $2K+, or nearly a 33% cost increase. This only brings a marginal increase in performance. The alternative to stay in budget is to take a hit on the fsb down to 800mhz or cut the number of cores in half, neither of which is attractive. The main cost culprit is the processor. IBM no longer offers the E5410. It's listed as a part, but not available in any of the server configs I've looked at. I'm considering getting the cheapest 800mhz fsb dual core xeon I can configure and then buying the E5410's separately. That's still an extra $350 I wasn't counting on, but that's better than $2K. I want to know what others think of this - will it work or will I end up with the wrong motherboard or some other issue? Am I missing a simple way to configure the server I really want? I don't really intend to do this, but one option to save some money back is to omit the redundant power supply. Since my redundancy plan for these system is to switch over to a completely different host, the extra power isn't fully necessary. That said, it's still very helpful to avoid even short downtimes while I switch over VMs. Has anyone done this?

  Read the article

• BluRay audio/video stuttering with PowerDVD 11, WinDVD 11 Pro, etc? Xonar/Auzen HD audio option?

  - by jrista

  I recently upgraded my Windows 7 MediaCenter HTPC due to a motherboard failure (really old motherboard and cpu, it was on its last legs.) I chose to upgrade to an i5 system with everything built into the motherboard. I did my due diligence, researched, and found some hardware that was within my budget. I ended up with: Core i5 2500K (3.3Ghz) Corsair XMS3 2x2Gb DDR3 (4Gb) ASUS P8H 61-M LE/CSM MicroCenter 64Gb SSD (Previous BluRay player, forget the brand) The system is pretty awesome, and plays everything I have perfectly. I almost went with an Atom solution, however there have been numerous notes that they do not play NetFlix Instant Watch well...and I am a heavy Netflix IW user. High definition BluRay rips work well, although they usually contain lower audio quality than the BluRay's they were ripped from. The real problem I am encountering is playing back BluRay video from discs. For some reason, I am encountering rather terrible stuttering problems with both the audio and video. The stuttering is synchronous in both, and occurs at seemingly random intervals. I've used PowerDVD 9, PowerDVD 11 trial, and WinDVD 11 Pro trial. All three have stuttering problems, although PowerDVD 11 seems to have the least. Watching system resource usage, CPU load is never above 20%, and memory usage tends to be a constant 1/3rd the total available system memory. When playback is fine, its superb...the video is crystal clear. The audio quality is ok, certainly not what I would expect from a BluRay disc. I did some research, and it seems that playing BluRay from a PC causes a downsampling of the audio? I am curious if the audio is my primary problem here, the cause of the stuttering I am encountering? When stuttering occurs, the audio gets REALLY bad, while the video just pauses momentarily every second until for whatever reason everything picks up and runs fine (usually after a few seconds to a couple minutes.) The audio chipset is a Realtek HD ALC887 8-channel, supposedly designed to support BluRay playback. Has anyone encountered any issues like this playing back bluray discs on a PC (namely with PowerDVD...WinDVD was FAR worse, and seemed to have real trouble even reading the discs, and I have no interest in fiddling with it further.) Is there any reason to suspect the video decoding as the problem?(Given how bad the audio gets during a stutter, and how clean the video remains, I am inclined to think the issue boils down to audio.) Is it even remotely possible that the motherboard, cpu, or ram are causing the stuttering (all three are pretty blazing fast...faster than the hardware that I replaced, which seemed to play BluRay fine with PowerDVD 9.) I've read a bit about the Asus Xonar HDAV 1.3 and the Auzen X-Fi HomeTheater HD home theater hi-fi audio cards. Seems they are the only way to get true full-quality, uncompressed BluRay audio bitstreaming over HDMI on a PC. None of the usual suspects seem to have these cards in stock, however. Are these cards worth getting? Are they even still available, or have they been discontinued (if so, that would indeed be sad...they sound simply fantastic.)

  Read the article

• Transparent proxy which preserves client mac address

  - by A G

  I have a customer that wants to intercept SSL traffic as it leaves their network. My proposed solution is to setup a proxy that is transparent and both layer 2 and layer 3 so it can simply be dropped into their network without any change in config required. The proxy has two NICs, one connected to the server, the other to the client. The client, proxy and gateway are under control of the customer, the server is not. For example: client --- Proxy --- gateway -|- server I have my proxy program configured with IP_TRANSPARENT socket option to it can respond to connections destined for a remote IP. I am using the following setup: iptables -t mangle -A PREROUTING -p tcp --dport 80 -j TPROXY --on-port 3128 --tproxy-mark 1/1 iptables -t mangle -A PREROUTING -p tcp -j MARK --set-mark 1 ip rule add fwmark 1/1 table 1 ip route add local 0.0.0.0/0 dev lo table 1 The client in question is on its own subnet and has been configured so that the proxy is the default gateway. The result is: Client sends a frame to the proxy; source IP is client, source mac is client, destination IP is server, destination mac is proxy Proxy forwards this frame to the gateway; source IP is proxy, source mac is proxy, destination IP is server, destination mac is gateway Gateway forwards this to the server and gets a response back. Gateway sends reply back to proxy; source IP is server, source mac is gateway, destination IP is proxy, destination mac is proxy Proxy forwards this reply to client; source IP is server, source mac is proxy, destination IP is client, destination mac is client. The tproxy and iptables configuration lets the proxy send packets with a non local ip address. Is there a way to make something transparent at the mac address level? That is, put the client on the same subnet as the gateway. The gateway sees the source IP and mac as that of the client, even though they originated from the proxy. Could this be done by configuring the proxy as a bridge then use ebtables to escalate the traffic to be handled by iptables? When I use ebtables to push something up to iptables, it appears my proxy program doesn't respond to the packets as they are destined for the gateways's mac address, not the proxy's. What are some other potential avenues I could investigate? EDIT: When the client and gateway are on different subnets (and client has set the proxy as the gateway), it works as described in 1 to 5. But I want to know if it is possible to have the client and gateway on the same subnet and have the proxy fully transparent (ie client is not aware of the proxy). Thanks! EDIT 2: I can configure the proxy as a bridge using brctl, but cannot find a way to direct this traffic to my proxy program - asked here Possible for linux bridge to intercept traffic?. Currently, with the description numbered 1 to 5, it operates at layer 3; it is transparent on the client side (client thinks it is talking to the server's IP), but not on the gateway side (gateway is talking to the proxy's IP). What I want to find out is, is it possible to make this operate at layer 2, so it is fully transparent? What are the available options I should research? Thanks

  Read the article

• Moving users folder on Windows-7 to another partition - bad idea?

  - by Donat

  Hi, I'd like to re-submit here a question posted by Benjol on Aug 17at 5:57 "Moving users folder on Windows Vista to another partition - bad idea?" (I can't post one than one link until I earn "10 reputation" and removed my "answer" there to post my follow-up questions here). I am anxiously getting ready at long last to to carry out a clean install (using custom install option) from Vista to Windows-7 Home Premium 64bit with the free upgrade I received late October. For my Vista system I successfully set-up last Summer a multi-partitions scheme with Users and Program Data on a a different partition than the operating system (see link below, and its subsequent links in my comment for details). http://tuts4tech.net/2009/08/05/windows-7-move-the-users-and-program-files-directories-to-a-different-partition/comment-page-1/#comment-562 I was planning a similar set-up for windows 7, a little more streamlined, with OS, Program Files on C:, Users and Program Data on D:, and TV media recording on a separate partition. Reading the Question submitted by Benjol, I am second guessing too. Is moving Users and Program Data on a different partition than the default primary partition with OS and Program Files such a good idea? The couple of people I talked to at the official Microsoft Windows 7 booth at CES 2010 gave the same answer to the intention of moving the Users profile folder to another partition. In a nutshell, they all told me that they used to do this in XP and less in Vista but not anymore with Windows 7... "It is stable, after two months still no problem" I had the feeling it was a scripted answer to emphasize how Windows 7 is so stable and efficient... (Will Windows-7 system not become bugged down over the course of several months to a year or two? Only time will tell) Long story short, I share the same view than Benjol expressed with respect to being "able to backup and restore system and user data independently." I just received a 2TB usb2, eSATA external hard drive as a back-up drive, which includes NTI Shadow 4 (4.1.0.150) for back-up solution. I took note of the issue with NTUSER.DAT and I will read more about Volume Shadow Copy Service (VSS) for Windows 7. I am willing to put the effort if placing Users and Program Data on a different partition would allow to restore a fresher OS+Program image when the system gets bugged down. Questions: Is it such a bad idea? What is the "easy route" referred by Benjol in his post? Is it to just relocate folders to another partition using the Folder property tool? (It is not practical for several users and might not provide a straightforward restore process of just OS and Program Files when needed.) I am starting to learn about Windows 7 libraries. Would Windows 7 libraries be another alternative to achieve this? All this reading to decide how to organize the partition scheme for my custom system is starting to be confusing. I apologize for this lengthy Question. It is my first day here on SuperUser and I am just learning how different from a discussion thread it is. Thank you in advance for all your suggestions and comments. Donat

  Read the article

• Set up lnux box for hosting a-z

  - by microchasm

  I am in the process of reinstalling the OS on a machine that will be used to host a couple of apps for our business. The apps will be local only; access from external clients will be via vpn only. The prior setup used a hosting control panel (Plesk) for most of the admin, and I was looking at using another similar piece of software for the reinstall - but I figured I should finally learn how it all works. I can do most of the things the software would do for me, but am unclear on the symbiosis of it all. This is all an attempt to further distance myself from the land of Configuration Programmer/Programmer, if at all possible. I can't find a full walkthrough anywhere for what I'm looking for, so I thought I'd put up this question, and if people can help me on the way I will edit this with the answers, and document my progress/pitfalls. Hopefully someday this will help someone down the line. The details: CentOS 5.5 x86_64 httpd: Apache/2.2.3 mysql: 5.0.77 (to be upgraded) php: 5.1 (to be upgraded) The requirements: SECURITY!! Secure file transfer Secure client access (SSL Certs and CA) Secure data storage Virtualhosts/multiple subdomains Local email would be nice, but not critical The Steps: Download latest CentOS DVD-iso (torrent worked great for me). Install CentOS: While going through the install, I checked the Server Components option thinking I was going to be using another Plesk-like admin. In hindsight, considering I've decided to try to go my own way, this probably wasn't the best idea. Basic config: Setup users, networking/ip address etc. Yum update/upgrade. Upgrade PHP: To upgrade PHP to the latest version, I had to look to another repo outside CentOS. IUS looks great and I'm happy I found it! cd /tmp #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm #rpm -Uvh epel-release-1-1.ius.el5.noarch.rpm #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-4.ius.el5.noarch.rpm #rpm -Uvh ius-release-1-4.ius.el5.noarch.rpm yum list | grep -w \.ius\. [will list all packages available in the IUS repo] rpm -qa | grep php [will list installed packages needed to be removed. the installed packages need to be removed before you can install the IUS packages otherwise there will be conflicts] #yum shell >remove php-gd php-cli php-odbc php-mbstring php-pdo php php-xml php-common php-ldap php-mysql php-imap Setting up Remove Process >install php53 php53-mcrypt php53-mysql php53-cli php53-common php53-ldap php53-imap php53-devel >transaction solve >transaction run Leaving Shell #php -v PHP 5.3.2 (cli) (built: Apr 6 2010 18:13:45) This process removes the old version of PHP and installs the latest. To upgrade mysql: Pretty much the same process as above with PHP #/etc/init.d/mysqld stop [OK] rpm -qa | grep mysql [installed mysql packages] #yum shell >remove mysql mysql-server Setting up Remove Process >install mysql51 mysql51-server mysql51-devel >transaction solve >transaction run Leaving Shell #service mysqld start [OK] #mysql -v Server version: 5.1.42-ius Distributed by The IUS Community Project The above upgrade instructions courtesy of IUS wiki: http://wiki.iuscommunity.org/Doc/ClientUsageGuide Create a chroot jail to hold sftp user via rssh. This will force SCP/SFTP and will circumvent traditional FTP server setup. #cd /tmp #wget http://dag.wieers.com/rpm/packages/rssh/rssh-2.3.2-1.2.el5.rf.x86_64.rpm #rpm -ivh rssh-2.3.2-1.2.el5.rf.x86_64.rpm #useradd -m -d /home/dev -s /usr/bin/rssh dev #passwd dev Edit /etc/rssh.conf to grant access to SFTP to rssh users. #vi /etc/rssh.conf Uncomment line allowscp This allows me to connect to the machine via SFTP protocol in Transmit (my FTP program of choice; I'm sure it's similar with other FTP apps). Above instructions for SFTP appropriated (with appreciation!) from http://www.cyberciti.biz/tips/linux-unix-restrict-shell-access-with-rssh.html And this is where I'm at. I will keep editing this as I make progress. Any tips on how to Configure virtual interfaces/ip based virtual hosts for SSL, setting up a CA, or anything else would be appreciated.

  Read the article

• Intermittent lockups, unable to diagnose in over a year

  - by Magsol

  Here's a real doosie; I may just give my firstborn child to whomever helps me solve this problem. In July 2008, I assembled what would be my desktop computer for graduate school. Here are the specs of the machine I built: Thermaltake 750W PSU Corsair Dominator 2x2GB 240-pin SDRAM Thermaltake Tower Asus P5K Deluxe Motherboard Intel Core 2 Quad Q9300 2.5GHz CPU 2 x GeForce 8600 GT WD Caviar Blue 640GB hard drive CD burner DVD burner Soon thereafter, I ordered a new motherboard (because I was an idiot; that first motherboard supported CrossFire, not SLI), an Asus P5N-D. I was originally running Windows XP SP3. Pretty much right into the start of the fall semester, my desktop would simply lock up after awhile. If my system was largely idling, it would be after 1-3 days. If was gaming, it often happened an hour or two into my gaming session, indicating a link to activity level. Here's where it started getting interesting. I started looking at the system temps. The CPU was warmer than it should have been (~60s C), so I purchased some more efficient cooling compound a way better cooler for it. Now it hardly goes over 40 C. Intel was even kind enough to swap it out for free, just to rule it out. Lockups continued. The graphics cards were also running pretty warm: about 60 C idling. Removing one of them seemed to improve stability a little bit...as in, it wouldn't lock up quite as frequently, but still always eventually locked up. But it didn't matter which card I used or removed, the lockups continued. I reverted back to the original motherboard, the P5K Deluxe. Lockups continued. I purchased an entirely new motherboard, eVGA's nForce 750i. Lockups continued. Ran memtest86+ over and over and over, with no errors. Even RMA'd the memory. Lockups continued. Replaced the PSU with a Corsair 750W PSU. Lockups continued. Tried disconnecting all IDE drives (HDDs are SATA). Lockups continued. Replaced both graphics cards with a single Radeon HD 4980. Average temps are now always around 50 C when idling, 60 C only when gaming. Lockups continued. Throughout the whole ordeal, the system has been upgraded from Windows XP SP3 to Vista 32-bit, to Vista 64-bit, and is now at Windows 7 64-bit. Lockups have occurred at every step along the way (each OS was in place for at least a few months before the next upgrade). Edit: By "upgrade" I mean clean install each time. In addition to those reformats, I have performed many, many other reformats of the system and a reinstall of whatever OS had been previously installed in an attempt to rectify this problem, to no avail./Edit When the system locks up, there's no blue screen, no reboot, no error message of any kind. It simply freezes in place until I hit the reset button. Very, very rarely, once Windows boots back up, the system informs me that Windows has recovered from an error, but it can never find the source aside from some piece of hardware. I've swapped out every component in this computer, and there are more fans in it than I care to count...though for the sake of completeness: top 80mm case fan (out) rear 80mm case fan (out) rear 120mm case fan (out) front 120mm case fan (in) side 250mm case fan (in) giant CPU fan on-board motherboard fan (the eVGA board) triple-fan memory setup (came with the memory) PSU internal fan another 120mm fan I stuck on the underside of the video card to keep hot air from collecting at the bottom of the case I'm truly out of ideas. ANY help at all would be oh-so-very GREATLY appreciated. Thank you!

  Read the article

• Dell Latitude E6430 Docking Station + Dual Monitor + Laptop Screen Tri-Monitor setup

  - by Larry

  I have a company issued laptop and docking station as well as two monitors The specifications of the hardware are as follows; Laptop: Latitude E6430 BIOS: A02.00 Processor: i7-3720QM CPU @ 2.60 (8 CPUs) Memory: 4096MB RAM Page file: 1825MB used, 4793MB available DirectX 11 Display Driver/Chip: MVIDIA NVS 5200M DAC: Integrated RAMDAC Aprox Total Memory: 2376 (Above 3 details same for both displays) Current Display Mode (Display 1): 1600x900 Current Display Mode (Display 2): 1440x900 the docking station is a Dell Latitude E6420 Docking Station PR03X Port Replicator and I don't think the monitor model is particularly relevant to resolving this issue but they are both Acer V193Ws The story goes like this; the laptop works fine if I VGA one monitor into the laptop through the vga port on the back of the lefthand side of the laptop I can achieve dual monitor display fine (laptop screen + monitor) if I plug the laptop into the docking station and use the vga port in the back of the docking station I can dual monitor fine (laptop screen + monitor) if I plug the laptop into the docking station, the laptop's lefthand side VGA port no longer seems to function at all I've spoken to internal IT about this issue and they're going to get me some kind of VGA splitter or a DVI-VGA adapter to use with the docking station for the second Acer Monitor, but that isn't going to happen for a few days. So I guess what I'm wondering is; is there any way to continue to use the side VGA port on my laptop while using the docking station VGA port? and as a secondary 'followup' pending resolution of the initial issue with getting both monitors up and running (at the moment I have both monitors on my desk but am just using my laptop screen as one of my dual monitor display with one of the monitors [the one connected to dock]), is there any way to CONTINUE to use my laptop monitor to in effect have a triple monitor display (2 monitors + docked laptop)? I am wondering this because internal IT told me that they were aware of some issues with the particular display drivers in my box and triple monitor displays but weren't really going to look TOO much in-depth into that (which is perfectly understandable) since getting the adapter for the dual monitors up and running was the greater priority within their purview. So this is a two parter; Can I dual monitor using two vga cables with 1 docking station vga port and one laptop vga port? is there a setting that can be tweaked somewhere? because plugging the box into the station seems to make the side port stop working and... Is there any reasonably simple and cost-effective work around (e.g. I am find with shelling out maybe a few dollars out of my own pocket for some hardware or software to make my company box tri-display capable) but if this requires some extensive rebuild or new OSs or doing stuff to the BIOS I'd rather have a straight answer about this being untenable as a slight modification to a (once again) company laptop and stop wasting time looking into it Thanks! and please let me know if you guys need any more details (tech specs or something) to answer this question [EDIT] 2/10/2014 Just an update; turned out it really was just a hardware limitation issue. The old laptop just couldn't hack it. Got a new laptop with a better video card and different monitors from my company and am successfully using a triple display currently (2 monitors + laptop screen)

  Read the article

• Putting indexes in separate filegroup kills our queries

  - by womp

  Can anyone shed some light on this? On our dev boxes, our database resides entirely in the PRIMARY filegroup, and everything works fine. On one of our production servers, recently upgraded from 2005 to 2008, we noticed it was performing slower than it should. On this machine, there are two filegroups - PRIMARY and INDEXES. Both filegroups contain 1 file per logical volume, one logical volume per CPU, (and each logical volume is a RAID 10 of 4 physical disks). We isolated a few queries that were performing fast on the dev boxes and slow (up to 40x slower) on the production machine. Turned out these queries were using the non-clustered indexes that resided in the INDEXES filegroup. Tweaking some of the queries to only use clustered indexes that were in the PRIMARY filegroup dropped their times back to normal. As a final confirmation, we redeployed the same database on the same machine to have everything in PRIMARY, and things went back to normal! Here's the statistics output of one of the queries, run identically on the machine with different filegroup configurations (table names changed to protect the innocent): FAST (everything in PRIMARY filegroup): (3 row(s) affected) Table '0'. Scan count 2, logical reads 14, ... Table '1'. Scan count 0, logical reads 0, ... Table '1'. Scan count 0, logical reads 0, ... Table '2'. Scan count 2, logical reads 7, ... Table '3'. Scan count 2, logical reads 1012, ... Table '4'. Scan count 1, logical reads 3, ... SQL Server Execution Times: CPU time = 437 ms, elapsed time = 445 ms. SLOW (indexes split into their own filegroup): (3 row(s) affected) Table '0'. Scan count 209, logical reads 428, ... Table '1'. Scan count 0, logical reads 0,... Table '2'. Scan count 1021, logical reads 9043,.... Table '3'. Scan count 209, logical reads 105754, .... Table '4'. Scan count 0, logical reads 0, .... Table '5'. Scan count 1, logical reads 695, ... **Table '#46DA8CA9'. Scan count 205, logical reads 205, ...** Table '6'. Scan count 6, logical reads 436, ... Table '7'. Scan count 1, logical reads 12,.... SQL Server Execution Times: CPU time = 17581 ms, elapsed time = 17595 ms. Notice the weird temp table and extra tables involved in the slow query. It seems clear that having a second file group is making SQL Server batty with choosing an execution plan. What the heck is going on?

  Read the article

• Windows XP Video Configuration Issues

  - by Matt

  Recently I had my motherboard burn out on me. Needing the machine for work, I purchased a different motherboard and installed that. Generally a reinstall of windows is good at that point but I am not in a position to do that so I just decided I would live with it for now. When I can log-in, everything works fine, what doesn't is getting to the log-in prompt to begin with. Basically when I first installed the new mobo, every time I rebooted the machine, I would not get the windows login prompt. One of the monitors would receive a signal but the screen would be black. Moving the mouse would not show the cursor and hitting the up arrow key and typing my password and hitting enter (which will normally log you in without mouse) wouldn't change anything. I would then change the monitor configuration around (2 lcd's and a crt) and reboot and at least one of the monitors would work and display the login prompt. I could then go into display properties and turn on the other monitors. However if I rebooted again, I would get the black screen on one monitor again. I would then have to change the configuration again to one not used before and I could re-do the manual setup at that point. I think windows saves the configurations so I had to keep giving it new ones. Needless to say I've been trying to not turn off my machine. Early this week I actually got the prompt to come up without playing musical monitors. Thinking everything was getting better, I found no harm in rebooting to install the latest windows updates. Boy was I wrong. Now no matter what I do I can't get a windows log-in prompt to display. I've tried almost every conceivable combination. The new mobo has onboard video so I set that in the bios (yea bios screen always displays fine, its not until windows boots that there is a problem) to be the primary video. Still no luck. I have two other graphics cards in the machine which I'm using. Tried all kinds of configurations between those and on-board but still get this black screen of death. I read somewhere that deleting the video drivers would reset the configurations. I logged into safe mode (which works on one monitor), and uninstalled the display drivers. Still no luck and when I booted back into safe mode, it wanted to install new hardware and the display adapters weren't there as expected. Anyone have any ideas? A fresh install would be a pain and I might be getting my old board back from RMA soon so not sure I want to go through with that just yet. Only thing I can think of is to continue to try other combinations like physically removing the graphics cards. They are both EVGA 8600 cards and the windows boot screen does display fwiw.

  Read the article

• How to diagnose computer lockups and freezes?

  - by Scott Mitchell

  I built a desktop computer a couple years back with the following specs: CPU: Intel Core 2 Quad Q9300 Yorkfield 2.5GHz 6 MB L2 Cache LGA 775 95W Quad-Core Processor BX80580Q9300 Motherboard: EVGA 122-CK-NF68-T1 LGA 775 NVIDIA nForce 680i SLI ATX Intel Motherboard Video Card: Two EVGA 256-P2-N758-TR GeForce 8600GT SCC 256 MB 128-bit GDDR3 PCI Express x16 SLI Supported Video Card PSU: SeaSonic S12 Energy Plus SS-550HT 550W ATX12V V2.3 / EPS12V V2.91 SLI Certified CrossFire Ready 80 PLUS Certified Active PFC Power Supply Memory: Two G.SKILL 4 GB (2 x 2 GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Dual Channel Kit Desktop Memory Model F2-6400CL5D-4GBPQ Since its inception, the machine has periodically locked up, the regularity having varied over the years from once a day to once a month. Typically, lockups happen once every few days. By "lockup" I mean my computer just freezes. The screen locks up, I can't move the mouse. Hitting keys on my keyboard that normally turn LEDs on or off on the keyboard (such as Caps Lock) no longer turn the LEDs on or off. If there was music playing at the time of the lockup, noise keeps coming out of the speakers, but it's just the current frequency/note that plays indefinitely. There is no BSOD. When such a lockup occurs I have to do a hard reboot by either turning off the computer or hitting the reset button. I have the most recent version of the NVIDIA hardware drivers, and update them semi-regularly, but that hasn't seemed to help. I am currently using Windows 7 x64, but was previously using Windows Server 2003 x64 and having the same lockup issues. My guess is that it's somehow video driver or motherboard related, but I don't know how to go about diagnosing this problem to narrow down which of the two is the culprit. Additional information re: cooling Regarding cooling... I've not installed any after-market cooling systems aside from two regular fans I scavenged from an older computer. The fan atop the CPU is the one that shipped with it. One of the two scavenged fans I added it located at the bottom tower of the corner, in an attempt to create some airflow from front to back. The second fan is pointed directly at the two video cards. SpeedFan installation and readings Per studiohack's suggestion, I installed SpeedFan, which provided the following temperature readings: GPU: 63C GPU: 65C System: 76C CPU: 64C AUX: 36C Core 0: 78C Core 1: 76C Core 2: 79C Core 3: 79C Update #3: Another Lockup :-( Well, I had another lockup last night. :-( SpeedFan reported the CPU temp at 38 C when it happened, and there was no spike in temperature leading up to the freeze. One thing I notice is that the freeze seems more likely to happen if I am watching a video. In fact, of the last 5 freezes over the past month, 4 of them have been while watching a video on Flickr. Not necessarily the same video, but a video nevertheless. I don't know if this is just coincidence or if it means anything. (As an aside, each night before bedtime my 2 year old daughter sits on my lap and watches some home videos on Flickr and, in the last month, has learned the phrase, "Uh oh, computer broke.") Update #4: MemTest86 and 3DMark06 Test Results: Per suggestions in the comments, I ran the MemTest86 overnight and it cycled through the 8 GB of memory 5 times without error. I also ran the 3DMark06 test without a problem (see my scores at http://3dmark.com/3dm06/15163549). So... what now? :-) Any further suggestions on what to check? Is there some way to get a stack trace or something when the computer locks like that? Resolution I have never did figure out the particular problems, but based on the suggestions here and elsewhere, I'm presuming it was a motherboard issue. In any event, I recently upgraded my system, buying a new motherbeard, PSU, CPU, and RAM, and that new rig has been working splendidly the past several weeks. I am using the same graphic cards as in the old setup, so I think it's safe to reason that they weren't the cause of the problem.

  Read the article

• Determining the required depth and specifications for a server cabinet

  - by Bingu Bingme

  I'm trying to understand the considerations ("why") that go into determining the specifications ("what") for a rackmount server cabinet, in order to determine what sort of rack I should purchase for my home use. Since this is for home use, I won't be following certain best practices (eg. hot/cold aisle, not even air conditioning) and may be willing to sacrifice in various areas in order to reduce cost and footprint - but please advise if there are safety concerns or other considerations to note. The most basic specs for a server cabinet are the dimensions (external width x external depth x usable height). Width: commonly 600mm or 800mm (if the use case requires extra clearance around the sides, such as if there is lots of cabling). In my case and most common cases, I'm going to stick with 600mm. Height: Select a sufficiently tall rack to fit my equipment. But how much may I stuff into it? Eg, if there is a 15U rack, can I really populate it with 15U of servers, or should I leave 1U at top and bottom for air circulation? Depth: Racks commonly have external depth of 600mm (network equipment), 800mm, 1000mm, or even longer. I'm trying to see how to fit into the 800mm depth. With reference to http://www.server-racks.com/rack-mount-depth.html, I'm hoping to have the front and rear posts mounted ~ 28.5" (72cm) apart, which would leave only 8cm for front space and rear space. How much rear space (from rear posts to back of rack) do I really need? I won't use cable management arms, so can I mount a 72cm depth server since the power, KVM, network cables won't take up much depth? My most important equipment are all < 60cm depth (4U chassis) and should comfortably fit within the 800mm cabinet. The rest of the equipment are very old 1U servers that range from 65-72cm depth. I might still want to make further use of them, or I might discard them since they are so old. Even if the 72cm servers cannot be powered on in an 800mm rack, I should be able to use them as 1U shelves. But, what server depth can I expect to be able to operate? Or am I forced to upgrade to 1000mm depth racks in order to use any servers deeper than 60cm? With reference to best practices for HP racks, some other specs and installation considerations: There aren't any minimum recommendations for clearance on the sides of the rack. It is recommended to leave 48" front clearance. The 48" front clearance is based on 32" chassis depth, 13" to extend the rack rails and mate the inner/outer rails, and 3" for movement. If I don't use such rails (eg, use shelves instead), it should be sufficient to leave front clearance of chassis depth + 3". It is recommended to leave 30" rear clearance "to provide space for servicing the rack". I'm planning to back the rack into a corner of the room, and wheel it slightly out when I need to access the rear. If the wheeling plan is ok, I still need to know how much rear clearance is required for air circulation and ventilation purposes. Castor wheels and stabilising feet. Since I'm backing the rack into a corner of the room, I'll only be able to set the stabilising feet on the front corners. Thoughts on safety? The rack that I'm considering has front glass doors with side ventilation slits and fully perforated rear doors. I'm hoping this will be a good balance between temperature and noise (only ventilation slits facing out the front, while the rear is facing the walls). Or is the sound of high-rpm fans going to escape through the front slits anyway and destroy my sanity?

  Read the article

• Causes of sudden massive filesystem damage? ("root inode is not a directory")

  - by poolie

  I have a laptop running Maverick (very happily until yesterday), with a Patriot Torx SSD; LUKS encryption of the whole partition; one lvm physical volume on top of that; then home and root in ext4 logical volumes on top of that. When I tried to boot it yesterday, it complained that it couldn't mount the root filesystem. Running fsck, basically every inode seems to be wrong. Both home and root filesystems show similar problems. Checking a backup superblock doesn't help. e2fsck 1.41.12 (17-May-2010) lithe_root was not cleanly unmounted, check forced. Resize inode not valid. Recreate? no Pass 1: Checking inodes, blocks, and sizes Root inode is not a directory. Clear? no Root inode has dtime set (probably due to old mke2fs). Fix? no Inode 2 is in use, but has dtime set. Fix? no Inode 2 has a extra size (4730) which is invalid Fix? no Inode 2 has compression flag set on filesystem without compression support. Clear? no Inode 2 has INDEX_FL flag set but is not a directory. Clear HTree index? no HTREE directory inode 2 has an invalid root node. Clear HTree index? no Inode 2, i_size is 9581392125871137995, should be 0. Fix? no Inode 2, i_blocks is 40456527802719, should be 0. Fix? no Reserved inode 3 (<The ACL index inode>) has invalid mode. Clear? no Inode 3 has compression flag set on filesystem without compression support. Clear? no Inode 3 has INDEX_FL flag set but is not a directory. Clear HTree index? no .... Running strings across the filesystems, I can see there are what look like filenames and user data there. I do have sufficiently good backups (touch wood) that it's not worth grovelling around to pull back individual files, though I might save an image of the unencrypted disk before I rebuild, just in case. smartctl doesn't show any errors, neither does the kernel log. Running a write-mode badblocks across the swap lv doesn't find problems either. So the disk may be failing, but not in an obvious way. At this point I'm basically, as they say, fscked? Back to reinstalling, perhaps running badblocks over the disk, then restoring from backup? There doesn't even seem to be enough data to file a meaningful bug... I don't recall that this machine crashed last time I used it. At this point I suspect a bug or memory corruption caused it to write garbage across the disks when it was last running, or some kind of subtle failure mode for the SSD. What do you think would have caused this? Is there anything else you'd try?

  Read the article

< Previous Page | 441 442 443 444 445 446 447 448 449 450 451 452  | Next Page >