Search Results

Search found 16035 results on 642 pages for 'connection pooling'.

Page 452/642 | < Previous Page | 448 449 450 451 452 453 454 455 456 457 458 459  | Next Page >

• how to stop deferred emails

  - by Will K

  I have a postfix mail gateway. At the same time, every other host is set to use this gateway as the relay. We have some automated outgoing emails sent from some hosts. I believe the gateway trys to send a deferred status back to the system started this. But that system is a null client, which sends but not receive any email Is there anyway to stop sending the deferred status? e.g. postfix/smtp[35725]: 2F6A155C256: to=, relay=none, delay=260862, delays=260862/0.01/0/0, dsn=4.4.1, status=deferred (connect to orange.mydom.com[192.168.1.5]:25: Connection refused) Thanks

  Read the article

• Windows 7 Built-In VPN - How to access network shares, printers, etc.?

  - by mbrion

  After I have successfully connected to a Windows 7 box via the built-in VPN: how do I access shares, shared printers, network appliances, etc.? So, call me bad at googling, but: I can find dozens of articles on "How to Set up a VPN Connection" and "How to connect to a VPN" for Windows 7... but I can't find a single article on how to access resources after connecting. I have a home VPN set up in Windows 7; I was able to connect to it from my friend's Windows 7 machine last night. I expected to be able to UNC into my shares; I also expected to be able to go to "Start Computer" and Click "Network" on the left side, and then see all of the devices on my home network (while the VPN was connected). Am I missing something obvious? How do I make this happen?

  Read the article

• Windows 7 Built-In VPN - How to access network shares, printers, etc.?

  - by Mike Brion

  After I have successfully connected to a Windows 7 box via the built-in VPN: how do I access shares, shared printers, network appliances, etc.? So, call me bad at googling, but: I can find dozens of articles on "How to Set up a VPN Connection" and "How to connect to a VPN" for Windows 7... but I can't find a single article on how to access resources after connecting. I have a home VPN set up in Windows 7; I was able to connect to it from my friend's Windows 7 machine last night. I expected to be able to UNC into my shares; I also expected to be able to go to "Start Computer" and Click "Network" on the left side, and then see all of the devices on my home network (while the VPN was connected). Am I missing something obvious? How do I make this happen?

  Read the article

• Cannot run gnome-session

  - by Brian

  I'm having issues running an X Windows session on a RHEL5 64-bit server - whenever I execute the command "gnome-session &", the process goes into the background but nothing happens. I have Exceed installed on my Windows machine which is running when I try to start the gnome-session. I've tried just starting firefox by itself instead of the whole gnome session, but it doesn't work either. Any suggestions? BTW, here's the error message I get when I try to start firefox: firefox: Fatal IO error 104 (Connection reset by peer) on X server localhost:10.0.

  Read the article

• Why are the prices for broadband bandwidth at data centers much higher than consumer/small business offerings?

  - by odemarken

  The prices for broadband bandwidth at data centers are sometimes as much as 10x higher than for a typical small business/consumer connection, at least where I live. Now, I understand those are two differend kind of products, but what exactly are the differences? Is it mainly because the bandwidth you get at a data center is guaranteed (CIR), while a consumer offer lists maximal bandwidth (EIR/MIR)? Or are there other factors as well? (Note: my previous, much more specific question on the same general topic was closed as not constructive. I tried to extract the core issue and present it in a way that can be answered objectively. If you feel that this question is still bad and should be closed, please care to comment and explain why.)

  Read the article

• How can I monitor ports on Windows?

  - by Olav

  What is the simplest way on "local" (1*) Windows, for known ports, to: Find out if it is used. Find out as much as possible about what is behind the port. Find out as much as possible about traffic through the port. Find out if something else is interfering with the port and traffic to it. I have used Fiddler in the past, but I think that's mostly HTTP? I don't if Wire-shark does more? I think there is a tool closely integrated with Windows? Which one? (5). I am looking at NMap, but its seems to be more a suite of tools, and a high entry level. 1*: Primarily this is for what happens inside my Windows Machine, but if necessary, I can for example use a VM, or the wireless connection.

  Read the article

• Multiple Session using port 1081 in one box using SSH

  - by regmaster

  Hi Guru's, I am setting Linux Hopping Station to another different servers. My current config to connect to another servers is using different port to connect. e.g ssh -D 1080 -p 22 [email protected] ssh -D 1081 -p 22 [email protected] Now what I would like to have to share the same port from the same box. ssh -D 1080 -p 22 [email protected] ssh -D 1080 -p 22 [email protected] But when I share it, I will get below error: bind: Address already in use channel_setup_fwd_listener: cannot listen to port: 1080 Could not request local forwarding. How could I configure the same port? help. thank you. I want to share the same port because this is needed when configuring firewall in Citrix Firewall on other machine, not needed to many many ports and keep changing when changing connection. thank you.

  Read the article

• Cisco 5505 VPN RDP not working

  - by user1058275

  I am in dire straights over here. We just changed our LAN from a 192.168.1.0 to a 172.16.4.0. We run Active Directory in our environment and our gateway is a Cisco 5505 ASA. Since the change, our clients can VPN in and make a connection but cannot RDP to any machines that they need to get to on the LAN that they VPN into. I updated the VPN address pool and DNS servers but I'm not sure what else I need to configure. I can send anything you need as I am not an expert and I really, really appreciate the help!

  Read the article

• Why my USB mouse get suspended after 3 seconds of inactivity?

  - by Vi.

  Mouse's bottom LED goes off after 3 seconds after connection and cursor movements and wheel stops. Pressing any button, reconnecting or resetting USB device resumes it for another 3 seconds (when resumed by pressing button, this event does no go to X). This happens when using any of USB ports. This mouse works well with other computer with Linux. It was working well before. Why can it happen? How to fix it? Update: It happens only if laptop is on battery. Answer: this is caused by powersaving done by laptop-mode-tools. To temporary turn off powersaving one can use for i in /sys/bus/usb/devices/*/power/control; do echo on > $i; done

  Read the article

• Why do I have inconsistent network issues with my laptop's wireless?

  - by Jason

  I'm having trouble with my laptop Internet connection. It's patchy at best and resets or freezes a lot. The signal strength is also random. I thought it might be a driver issue but now I don't know. Three other computers using the same wireless network run well. I've switched out wireless routers so I don't think it's the router. I thought it might be the laptop's internal wireless card but I just bought an external USB network card and I'm still having problems. Specs Lenovo T-60p Windows 7 Ultimate Edition Patches/drivers are up to date I only use one of the below at a time, disabling the other: Intel PRO/Wireless 3945ABG v. 13.3.0.137 (Internal wireless) Medialink Wireless-N USB 2.0 Adapter (USB wireless) Any ideas on what might be the problem?

  Read the article

• Put Google Chrome, AVG on a flash drive

  - by duncan12

  I often install programs on others' computers such as LibreOffice, which, when they only have a dial-up connection, takes forever to download. So instead I keep it on a flash drive and install it from there. This works fine for LibreOffice. However, some programs, when you download them all you are downloading is a downloader - when you download ChromeSetup and open it, a installer window opens which actually downloads Chrome. Dial-up users then see that it will take 4 hours. Another example is AVG free antivirus - you download an installer, which when opened actually downloads AVG. However this doesn't work too well for dial-up users. How do I put the entire program of things like Chrome and AVG on a flash drive for fast installation on others' slow connections?

  Read the article

• How much visitors could handle my server ?

  - by coolboycsaba

  I have a website, and I want to host it on my own computer, but I'm wondering if it's good enough. The website check`s if the user is logged in and then displays 15 items (title, description) from a mysql database and the rating (stored in another database) and the comments (another database) for each item. It also displays some stats (number of items, comments). I also have an image for each item. My specs are: AMD Athlon 64 X2 Dual Core Processor 5600+ 2.90 GHz RAM memory: 4.00GB Windows 7 64bit So what do you think, how much visitors and items could it handle (at once or daily) ? My internet connection is good, around 7-10 mb upload and same download speed

  Read the article

• What does VNC reflectors basically do?

  - by honeybadger

  I am confused about what vnc reflector does. From the documentation http://sourceforge.net/projects/vnc-reflector/ I got that it's proxysitting between real VNC server (a host) and a number of VNC clients. My confusion is : 1. Does it make any changes to the coming stream from server 2. Does it make 1 connection with server to connect to many client or the connections are proportionate. Documentation is not clear in this. If anyone can help me?

  Read the article

• EC2 Windows 2008 VM import Not Working

  - by remack

  I am trying to upload a Windows 2008 SP2 server image to Amazon EC2, but once the process is complete, I can't connect to it. I had ops export a VMDK from our datacenter. The image appeared to have a fixed IP, so I loaded it in VMWare player and enabled DHCP. I uploaded it following amazon's instructions: http://aws.amazon.com/ec2/vmimport/ I start the new instance and try to RDP to the public DNS; connection fails. My two thoughts are: Loading it in VMWare player messed it up somehow, since the instructions say use an ESX image. The image they made me had the wrong network adapter type. The image has an Intel(R) PRO/1000 MT adapter using the E1G60I32.sys driver.

  Read the article

• Is it possible for a router to "go bad" with time?

  - by JQAn

  I've been having problems with my internet connection over the past weeks (intermittent disconnections, slow transfers, etc), and my provider keeps telling me that the problem is not on their end. I have cablemodem with a wifi router (this router was not provided by them). The router is quite old (DIR-300), so I'm starting to wonder if it could be the issue and if I should replace it. Is it possible that it is the cause? Can they become so outdated that they cause intermittent interruptions of service? If I reset the modem and the router, they work fine for a few hours, but the problems starts again after a while.

  Read the article

• OSX : Setup for filestorage in medium business

  - by Franatique

  In our office every machine runs OSX. In search of an ideal storage and sharing solution we decided to let OSX Server handle all account information and auth requests whereas an 7TB QNAP provides NFS shares. All shares are published as mounts in the companywide LDAP. As it turns out, handling permissions in this situation is very clumsy (e.g. inherit permissions on newly created files). Unfortunately using NFS4 in combination with ACLs did not solve the problem. As a possible solution I set up a iSCSI connection between QNAP and the machine running OSX Server which in turn serves the LUN as AFP share. Permission handling works like a charm for this setup. Although I am a bit concerned about the performance of this setup. As we are a fast growing company we expect the solution to serve at least 100 clients while using files aprox. above 100MB each. Are there any known drawbacks of this solution?

  Read the article

• Firefox unable to load SSL Certificate Chain, while Chrome, IE do

  - by FryBurger

  I created a certificate for our IIS 6 by sending a request (created with openssl) to our organization's CA. I already had trouble to integrate the private key into that certificate, that has been solved, see SO question IIS 6.0 now uses the certificate (with TSL v1 and SSL v3), that is the 4th in cert hierarchy. Now, if I access the intranet site, chrome accepts the certificate, so does IE, but Firefox complains about an insecure connection and wants me to add an exceptional rule. If I look into the certificate, how FF presents it to me, I cannot see any of the three issuers. How can this be? If I connect via openssl s_client -showcerts -connect... I only see my own certificate too, which is said to be not verified. I am quite confused now. Where's the mistake and how can I make FF accept certificate without forcing our users to add that exceptionrule? Maybe do I have to add all the three issuer certificates into cert store of the win2003 server that hosts IIS 6.0 ??

  Read the article

• Release Notes for 6/28/2012

  Here are the notes for this week’s release on CodePlex: Improved the diff viewer to take you directly to the first diff when viewing a file’s diff. We decreased the size of all of our form elements to be more in line with the rest of the content of our site. Fixed various issues around interacting with the diff viewer, especially around scrolling and interacting with the splitter. Fixed an issue where non-project members were seeing inapplicable TFS connection instructions when clicking on the source code details of a project. Fixed an issue where searching with the enter key on the advanced issue tracker was not working. Removed the confirmation pop-up when picking SVN as a source control option. Fixed an issue where the bulk editing dialog of issues in Internet Explorer would become unusable if there were values to choose. Fixed an issue where project logos would not show up when browsing under https in FireFox and Chrome. Fixed an issue affecting the formatting of code in pull request code comment notifications. Have ideas on how to improve CodePlex? Visit our ideas page! Vote for your favorite ideas or submit a new one. Got Twitter? Follow us and keep apprised of the latest releases and service status at @codeplex.

  Read the article

• Error code 0x80070035. The network path was not found

  - by user144606

  My system is connected with a local LAN connection with 30 PC's. I'm not able to access the shared drive in the network, but I'm able to ping the IP address in which the drive is present. I have checked to start all the services, which are to be started and i have check the TCP/UDP ports also, but even after that I'm not able to access the drive, the same error message is being displayed again and again. Please help me to rectify the problem. I'm trying to solve the problem for the last 1 week. I have tried various solutions which are present in various web site, but I'm not able to find a proper solution. So please help me.

  Read the article

• Synergy stopped moving cursor over to client computer (config worked previously)

  - by crazedgremlin

  I am using QuickSynergy on OSX on my client computer and the standard Synergy program on Windows. I had a configuration that worked two days ago when I last used it, but today I came into work and it wasn't working. The odd thing is that the server shows that the client connects: NOTE: started server, waiting for clients NOTE: accepted client connection NOTE: client "danbook.local" has connected It's just that the cursor won't move to the other screen. The only change in either of my systems was that I added 4GB of RAM to the client, though that seems unimportant. What might cause this to happen?

  Read the article

• Is it possible to access internet on smart-phone through usb (no wi-fi) using Laptop as the modem?

  - by Prahlad Yeri

  One of my relatives has a nokia 5235 smartphone. It is good, but the only limitation is - there is no wifi. bluetooth & usb are the only connectivity options. His laptop has an unlimited broadband but no support for bluetooth, so basically usb is the only method by which he can connect the mobile with laptop. Now, he can do a file-transfer between these two devices, but by any chance, is there a way by which we can share the Laptop's internet connection through usb to the smart-phone? So, bascially its like this: Broadband-modem = Laptop =usb= smart-phone -(want to use internet here) Are there any software or utilities available to achieve this ?

  Read the article

• website lookup extremely slow in ubuntu

  - by ubuntulover

  Hi I have a wireless broadband connection through a router and wireless modem. Everything works fine in Windows. However, in ubuntu on the same machine, websites seem to take longer to start loading. I think the dns lookup is slow. I think https sites may be slower, as Ijust can't log in to gmail. I am also using a mercurial repo with remote origin, and it takes forever (like 5 minutes) to push one small change. I think it is because it has to communicate through https multiple times. Should I change my dns server? I've seen that I don't have these problems at my work network (they have another dns server). This happens with the IPv4 settings being automatic (dhcp). When I change it to automatic (dhcp) addresses only, and add google's 8.8.8.8 in the dns servers, it still takes forever. Why is this happening?

  Read the article

• website lookup extremely slow in ubuntu

  - by ubuntulover

  Hi I have a wireless broadband connection through a router and wireless modem. Everything works fine in Windows. However, in ubuntu on the same machine, websites seem to take longer to start loading. I think the dns lookup is slow. I think https sites may be slower, as Ijust can't log in to gmail. I am also using a mercurial repo with remote origin, and it takes forever (like 5 minutes) to push one small change. I think it is because it has to communicate through https multiple times. Should I change my dns server? I've seen that I don't have these problems at my work network (they have another dns server). This happens with the IPv4 settings being automatic (dhcp). When I change it to automatic (dhcp) addresses only, and add google's 8.8.8.8 in the dns servers, it still takes forever. Why is this happening?

  Read the article

• Can i connect my modem's ethernet and usb slot to two computers simultaneously??

  - by Rajasekar

  I have NETGEAR BROADBAND MODEM. I had a desktop and laptop. I had connected internet to dekstop by using Ehternet slot on my modem to my ethernet slot on my Desktop. I need internet connection on my Laptop too. There is another slot in modem which can be connect using USB cable. Whether i can connect the laptop with that USB slot in my modem and use both the computer's internet? whether it will work??

  Read the article

• ftp-client works fine. ftp-tls-client fails on one computer and works on another

  - by ispiro

  Connecting to ftp - from a Windows Server 2012 - it works both secure (-over tls) and unsecure. From a Windows 7 it succeeds unsecure but fails when secure. (Using explicit TLS and passive mode.) filezilla: 234 AUTH command ok. Expecting TLS Negotiation. Initializing TLS... Connection timed out I've tried many things but nothing helps. (I'm also trying this programmatically. For details see: http://stackoverflow.com/questions/25393716/ftp-ssl-fails-after-expecting-tls-negotiation ) The fact that it does succeed from one computer proves that the ftp server is fine. And the fact that the Windows 7 computer succeeds without tls proves that it's not a NAT/firewall problem (besides, it failed even after disabling firewall etc.). I'm not sure where to start looking. Perhaps a difference between PC Windows and Windows Server? EDIT The ftp server is on a Windows Server 2012.

  Read the article

< Previous Page | 448 449 450 451 452 453 454 455 456 457 458 459  | Next Page >