Search Results

Search found 14780 results on 592 pages for 'low level'.

Page 463/592 | < Previous Page | 459 460 461 462 463 464 465 466 467 468 469 470  | Next Page >

• Win7 System folder contains infinitely looping SYSTEM(!) directory

  - by Matt

  My Windows 7 Enterprise computer has been crashing fairly frequently recently, so I decided to boot up in safe mode and run the TrendMicro client I have installed. It froze about 10 minutes into the full system scan, so in the spirit of http://whathaveyoutried.com, I started scanning each folder individually. When I got to ProgramData, the AV failed with an uncaught exception. I then went down a level and tried scanning Application Data, which failed as well. Imagine my surprise when I open the folder just to see the same folder again! As far as I can tell, this folder loop continues indefinitely. (If you are trying to recreate this, keep in mind that ProgramData is a hidden folder.) I'm actually a bit concerned that these are system folders, as this is a brand-new computer with a clean installation. I guess I have three questions: Has anyone else seen/experienced this before? I'm running Win7 SP1. How do I fix this? I've run CHKDSK \F with no success (although it was incredibly slow). What are the ramifications of an infinitely recursive directory? Theoretically speaking, each link takes up memory, so shouldn't I have no space available on my hard drive? (I've got about 180GB left.) I noticed that the tree view on the left only shows the "linked folder" icon on the deeper folders--does this mean anything special? (I've circled the icons or lack thereof in red.) How can the OS even resolve this aberration? And above all, what would happen if I were to select "Expand all folders"??? :P Matt

  Read the article

• How can I password protect an IIS directory with only FTP access?

  - by Tony Adams

  How can I password protect an IIS directory when I only have FTP access to the server? I can't adjust any IIS settings or add users or anything like that. The answer to: IIS Basic Authorization ala .htaccess/.htpasswd in apache does not help as I only have access to the server via FTP. I just need to password protect a directory. I've tried several variations of a web.config file. I can get a basic HTTP auth form to pop up when a user attempts to load a page from my test directory, but I can't configure the authentication part. The server complains that: Parser Error Message: It is an error to use a section registered as allowDefinition='MachineToApplication' beyond application level. This error can be caused by a virtual directory not being configured as an application in IIS. whenever I add an <authentication> section to my web.config. I'm grateful for any help anyone can offer. Edit: I don't know what version of IIS is running on this server, but here is the server tag from error messages: Version Information: Microsoft .NET Framework Version:1.1.4322.2490; ASP.NET Version:1.1.4322.2494

  Read the article

• VPN Setup: Mac OS X and SonicWall

  - by noloader

  I'm trying to get VPN access up and running. The company has a SonicWall firewall/concentrator and I'm working on a Mac. I'm not sure of the SonicWall's hardware or software level. My MacBook Pro is OS X 10.8, x64, fully patched. The Mac Networking applet claims the remote server is not responding. The connection attempt subsequently fails: This is utter bullshit, as a Wireshark trace shows the Protected Mode negotiation, and then the fallback to Quick Mode: I have two questions (1) does Mac OS X VPN work in real life? (2) Are there any trustworthy (non-Apple) tools to test and diagnose the connection problem (Wireshark is a cannon and I have to interpret the results)? And a third question (off topic): what is broken in Cupertino such that so much broken software gets past their QA department? EDIT (12/14/2012): The network guy sent me "VPN Configuration Guide" (Equinox document SonicOS_Standard-6-EN). It seems an IPSec VPN now requires a Firewall Unique Identifier. Just to be sure, I revisited RFC 2409, where Main Mode, Aggressive Mode, and Quick Mode are discussed. I cannot find a reference to Firewall Unique Identifier. I think I am screwed here: I am trying to connect to a broken (non-standard) firewall, with a broken Mac OS X client. Fortunately, I can purchase VPN Tracker Personal (a {SonicWall|Equinox}-authored client) for $129US from Equinox. So much for standards....

  Read the article

• ps aux as non-root doesn't show all processes

  - by JMW

  hi, i'm using an ubuntu 10.04 server... when i run ps aux as root i see all processes when i run ps aux as nonroot i see JUST the processes of the current user after a bit of research i found the following solution: root@m85:~# ls -al /proc/ total 4 dr-xr-xr-x 122 root root 0 2010-12-23 14:08 . drwxr-xr-x 22 root root 4096 2010-12-23 13:30 .. dr-x------ 6 root root 0 2010-12-23 14:08 1 dr-x------ 6 root root 0 2010-12-23 14:08 10 dr-x------ 6 root root 0 2010-12-23 14:08 1212 dr-x------ 6 root root 0 2010-12-23 14:08 1227 dr-x------ 6 root root 0 2010-12-23 14:08 1242 dr-x------ 6 zabbix zabbix 0 2010-12-24 23:52 12747 [...] my first idea was, that it got mounted in a weird way: /etc/fstab is ok and it doesn't seem to be mounted in an weird way... my second idea was, that there might be a rootkit: but it's not a rootkit... rkhunter tells me, that there is no rootkit installed... i don't know if it is since the machine got installed or came with an update. i've just installed zabbix-agent on the machine and realized, that it didn't work properly... What could have caused such strange permissions (500) and how can i set it back to an normal level (555) ? Crazy, i've never seen something like that... thanks in advance for any help and merry christmas :) see you

  Read the article

• Understanding encryption Keys

  - by claws

  Hello, I'm really embarrassed to ask this question but its the fact that I don't know anything about encryption. I always avoided it. I don't understand the concept of encryption keys (public key, private key, RSA key, DSA key, PGP Key, SSH key & what not) . I did encounter these in regular basis but as I said I always avoided them. Here are few instances where I encountered: Creating Account: A public RSA or DSA key will be needed for an account. Send the key along with your desired account name to [email protected] I really don't know what are RSA/DSA or How to get their keys? Do I need to register some where for that? Mailing: I'm unable to recall exactly but I've seen some mails have some attachments like signature or the mail footer will have something called PGP signature etc.. I really don't get its concept. GIT Version control: I created account in assembla.com (for private GIT repo) and it asked me to enter "SSH keys" to my profile. Where am I gonna get these? Why do I need it? Isn't SSH related to remote login (like remote desktop or telnet)? How are these two SSHs related & differ? I don't know in how many more situations I'm going to encounter these things. I'm really confused and have no clue about where to start & how to proceed to learn these things. Kindly someone point me in correct direction. Note: I've absolutely zero interested in encryption related topics. So, there is no way I'm going to read a graduate level book on this subject. I just want to clear my concepts without going into much depth.

  Read the article

• Python module: Trouble Installing Bitarray 0.8.0 on Mac OSX 10.7.4

  - by Gabriele

  I'm new here! I have trouble installing bitarray (vers 0.8.0) on my Mac OSX 10.7.4. Thanks! ('gcc' does not seem to be the problem) Last login: Sun Sep 9 22:24:25 on ttys000 host-001:~ gabriele$ gcc -version i686-apple-darwin11-llvm-gcc-4.2: no input files host-001:~ gabriele$ Last login: Sun Sep 9 22:18:41 on ttys000 host-001:~ gabriele$ cd /Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/site-packages/bitarray-0.8.0/ host-001:bitarray-0.8.0 gabriele$ python2.7 setup.py installrunning install running bdist_egg running egg_info creating bitarray.egg-info writing bitarray.egg-info/PKG-INFO writing top-level names to bitarray.egg-info/top_level.txt writing dependency_links to bitarray.egg-info/dependency_links.txt writing manifest file 'bitarray.egg-info/SOURCES.txt' reading manifest file 'bitarray.egg-info/SOURCES.txt' writing manifest file 'bitarray.egg-info/SOURCES.txt' installing library code to build/bdist.macosx-10.6-intel/egg running install_lib running build_py creating build creating build/lib.macosx-10.6-intel-2.7 creating build/lib.macosx-10.6-intel-2.7/bitarray copying bitarray/__init__.py -> build/lib.macosx-10.6-intel-2.7/bitarray copying bitarray/test_bitarray.py -> build/lib.macosx-10.6-intel-2.7/bitarray running build_ext building 'bitarray._bitarray' extension creating build/temp.macosx-10.6-intel-2.7 creating build/temp.macosx-10.6-intel-2.7/bitarray gcc-4.2 -fno-strict-aliasing -fno-common -dynamic -isysroot /Developer/SDKs/MacOSX10.6.sdk -arch i386 -arch x86_64 -g -O2 -DNDEBUG -g -O3 -I/Library/Frameworks/Python.framework/Versions/2.7/include/python2.7 -c bitarray/_bitarray.c -o build/temp.macosx-10.6-intel-2.7/bitarray/_bitarray.o unable to execute gcc-4.2: No such file or directory error: command 'gcc-4.2' failed with exit status 1 host-001:bitarray-0.8.0 gabriele$

  Read the article

• Controller Error: Do I need to worry?

  - by Kryten

  I have a HP Pavillion dv5224ea Laptop with Windows 7 on it. Recently I discovered a Error in Event Viewer: The driver detected a controller error on \Device\Ide\IdePort1. (more details): - System - Provider [ Name] atapi - EventID 11 [ Qualifiers] 49156 Level 2 Task 0 Keywords 0x80000000000000 - TimeCreated [ SystemTime] 2010-03-07T12:43:07.090197600Z EventRecordID 30198 Channel System Computer Alistair-Win7 Security - EventData \Device\Ide\IdePort1 0000100001000000000000000B0004C002000000850100C00000000000000000000000000000000000000000000000000000000004100000 -------------------------------------------------------------------------------- Binary data: In Words 0000: 00100000 00000001 00000000 C004000B 0008: 00000002 C0000185 00000000 00000000 0010: 00000000 00000000 00000000 00000000 0018: 00000000 00001004 In Bytes 0000: 00 00 10 00 01 00 00 00 ........ 0008: 00 00 00 00 0B 00 04 C0 .......À 0010: 02 00 00 00 85 01 00 C0 ......À 0018: 00 00 00 00 00 00 00 00 ........ 0020: 00 00 00 00 00 00 00 00 ........ 0028: 00 00 00 00 00 00 00 00 ........ 0030: 00 00 00 00 04 10 00 00 ........ Event Viewer is recording A LOT of these errors (sometimes 13, one after the other!). Do I need to worry? What does this error mean? What device could "\Device\Ide\IdePort1" be? What is a ATAPI Error? Do I need to re-install Windows? I generally find the occurs when I try to backup my machine (using Windows Backup) or when using a program that uses Volume Shadow Copy. I have run "sfc", no problems. There are no Device Errors in Device Manager. I have also run "vssadmin list writers", no problems. Whats going on??? Would it be a good idea to re-install Windows 7?

  Read the article

• NTLM, Kerberos and F5 switch issues

  - by G33kKahuna

  I'm supporting an IIS based application that is scaled out into web and application servers. Both web and applications run behind IIS. The application is NTLM capable when IIS is configured to authenticate via Kerberos. It's been working so far without a glitch. Now, I'm trying to bring in 2 F5 switches, 1 in front of the web and another in front of the application servers. 2 F5 instances (say ips 185 & 186) are sitting on a LINUX host. F5 to F5 looks for a NAT IP (say ips 194, 195 and 196). Created a DNS entry for all IPs including NAT and ran a SETSPN command to register the IIS service account to be trusted at HTTP, HOST and domain level. With the Web F5 turned on and with eachweb server connecting to a cardinal app server, when the user connects to the Web F5 domain name, trust works and user authenticates without a problem. However, when app load balancer is turned on and web servers are pointed to the new F5 app domain name, user gets 401. IIS log shows no authenticated username and shows a 401 status. Wireshark does show negotiate ticket header passed into the system. Any ideas or suggestions are much appreciated. Please advice.

  Read the article

• Automated Linux VMs on Hyper-V 2012

  - by Mick

  I have a requirement to create a ton of linux VMs for our customers (we run managed infrastructure) on Hyper-V 2012 in the coming months and I have an issue with automating it. Here is how I need it to work: User accesses their web page and creates a VM. VM is created with a unique IP and name User logs in over SSH I know Hyper-V quite well and can work with powershell and am a C# programmer so the development side of things is taken care of. I also know enough about Linux to be at least competent: I have used it on and off for a number of years but not done anything Enterprise-level with it. All this can be done easily by manual processes but I need to be able to script or program this to automate it as there could be hundreds of them being created but I don't know how. My first thought is to have a database with random-generated names and IPs already created but I don't know how to get a Linux VM to boot up and grab one from the database... I suppose a Kickstart script would take care of it but I don't know what to do from there. Here is what is bouncing around in my head: Create a std linux build. - Easy to do Someone clicks "Create VM" and I pull a name and IP from the database and write it to a kickstart script. - Easy to do I could then open the template VHDX file and copy in the script and then save it. - Not sure if possible User boots up new VM and the kickstart script gives it the name and IP I assigned it. My problem is that I don't know how to open a VHDX file and insert a kickstart script into it... can't figure it out. I am reaching here and this solution may be miles off... I am more used to creating Windows VMs with scripts and so on which i am more familiar with... any help would be appreciated. Thanks Mick

  Read the article

• How to turn off Tomcat logging in Eclipse?

  - by kirdie

  I develop a Vaadin project in Eclipse that I start through Tomcat 6 which gets started directly by Eclipse. Tomcat prints an enormous amount of log messages though on each start which makes it hard to see the output of my own Application. I have already replaced all log levels in tomcat6/conf/logging.properties by WARNING (e.g. java.util.logging.ConsoleHandler.level = WARNING) but I still get many INFO messages. How can I turn this off or restrict the log messages to WARNING? An example of the messages Okt 26, 2012 12:16:36 PM org.apache.catalina.core.AprLifecycleListener init INFO: Loaded APR based Apache Tomcat Native library 1.1.24. Okt 26, 2012 12:16:36 PM org.apache.catalina.core.AprLifecycleListener init INFO: APR capabilities: IPv6 [true], sendfile [true], accept filters [false], random [true]. Okt 26, 2012 12:16:36 PM org.apache.tomcat.util.digester.SetPropertiesRule begin WARNING: [SetPropertiesRule]{Server/Service/Engine/Host/Context} Setting property 'source' to 'org.eclipse.jst.j2ee.server:saim' did not find a matching property. Okt 26, 2012 12:16:37 PM org.apache.coyote.http11.Http11AprProtocol init INFO: Initializing Coyote HTTP/1.1 on http-8080 Okt 26, 2012 12:16:37 PM org.apache.coyote.ajp.AjpAprProtocol init INFO: Initializing Coyote AJP/1.3 on ajp-8009 Okt 26, 2012 12:16:37 PM org.apache.catalina.startup.Catalina load INFO: Initialization processed in 879 ms Okt 26, 2012 12:16:37 PM org.apache.catalina.core.StandardService start INFO: Starting service Catalina Okt 26, 2012 12:16:37 PM org.apache.catalina.core.StandardEngine start INFO: Starting Servlet Engine: Apache Tomcat/6.0.32 Okt 26, 2012 12:16:37 PM org.apache.coyote.http11.Http11AprProtocol start INFO: Starting Coyote HTTP/1.1 on http-8080 Okt 26, 2012 12:16:37 PM org.apache.coyote.ajp.AjpAprProtocol start INFO: Starting Coyote AJP/1.3 on ajp-8009 Okt 26, 2012 12:16:37 PM org.apache.catalina.startup.Catalina start INFO: Server startup in 568 ms

  Read the article

• Enabling JMX for proxool with tomcat

  - by dialt0ne

  I am trying to get proxool's MBeans available so that I can see/manipulate them with jconsole. I have jconsole working, but I don't see anything related to proxool. The system is using Sun Java 1.5.0_17 (I know, I know... I'm working with the developers to upgrade). JMX is enabled by modifying $JAVA_OPTS in my tomcat 5.5 startup script: SJO="$SJO -Dcom.sun.management.jmxremote" SJO="$SJO -Dcom.sun.management.jmxremote.port=4998" SJO="$SJO -Dcom.sun.management.jmxremote.authenticate=false" SJO="$SJO -Dcom.sun.management.jmxremote.ssl=false" JAVA_OPTS="$JAVA_OPTS $SJO" I have proxool configured with JNDI in server.xml: <GlobalNamingResources> <Resource name="jdbc/database" auth="Container" type="javax.sql.DataSource" factory="org.logicalcobwebs.proxool.ProxoolDataSource" user="username" password="password" proxool.driver-url="jdbc:oracle:thin:@fqdn.example.com:1521:MYSID" proxool.driver-class="oracle.jdbc.driver.OracleDriver" proxool.alias="mysid" proxool.maximum-connection-count="20" proxool.statistics="20s,5m,15m" proxool.statistics-log-level="INFO" proxool.jmx="true" proxool.verbose="true" /> </GlobalNamingResources> My test .jsp can run queries and I can see it using the connections with the proxool admin servlet, but I'm unsure if there's more I need to configure in tomcat or proxool to get JMX functioning. Advice? jmxproxy info edit: The jmxproxy servlet is working - when I go to the URL http://tomcatserver.example.com:4999/manager/jmxproxy/?qry=*:type%3DRequestProcessor,* the results are: OK - Number of results: 2 Name: Catalina:type=RequestProcessor,worker=http-8080,name=HttpRequest0 modelerType: org.apache.coyote.RequestInfo bytesSent: 0 requestBytesSent: 0 contentLength: -1 bytesReceived: 0 requestProcessingTime: 1297983483666 globalProcessor: org.apache.coyote.RequestGroupInfo@32dc51c8 requestBytesReceived: 0 serverPort: -1 stage: 0 requestCount: 0 maxTime: 0 processingTime: 0 errorCount: 0 Name: Catalina:type=RequestProcessor,worker=jk-127.0.0.1-8009,name=JkRequest794 modelerType: org.apache.coyote.RequestInfo virtualHost: tomcatserver.example.com bytesSent: 0 method: GET remoteAddr: 172.30.3.51 requestBytesSent: 0 contentLength: -1 workerThreadName: TP-Processor15 bytesReceived: 0 requestProcessingTime: 9 globalProcessor: org.apache.coyote.RequestGroupInfo@1e7d3b8e protocol: HTTP/1.1 currentQueryString: qry=*%3Atype%3DRequestProcessor%2C* requestBytesReceived: 0 serverPort: 4999 stage: 3 requestCount: 0 maxTime: 0 processingTime: 0 currentUri: /manager/jmxproxy/ errorCount: 0 And more to the point http://tomcatserver.example.com:4999/manager/jmxproxy/?qry=Catalina:type%3DEnvironment,resourcetype%3DGlobal,name%3DProxool yields: OK - Number of results: 0

  Read the article

• mkfs Operation Takes Very Long on Linux Software Raid 5

  - by Elmar Weber

  I've set-up a Linux software raid level 5 consisting of 4 * 2 TB disks. The disk array was created with a 64k stripe size and no other configuration parameters. After the initial rebuild I tried to create a filesystem and this step takes very long (about half an hour or more). I tried to create an xfs and ext3 filesystem, both took a long time, with mkfs.ext3 I observed the following behaviour, which might be helpful: writing inode tables runs fast until it reaches 1053 (~ 1 second), then it writes about 50, waits for two seconds, then the next 50 are written (according to the console display) when I try to cancel the operation with Control+C it hangs for half a minute before it is really canceled The performance of the disks individually is very good, I've run bonnie++ on each one separately with write / read values of around 95 / 110MB/s. Even when I run bonnie++ on every drive in parallel the values are only reduced by about 10 MB. So I'm excluding hardware / I/O scheduling in general as a problem source. I tried different configuration parameters for stripe_cache_size and readahead size without success, but I don't think they are that relevant for the file system creation operation. The server details: Linux server 2.6.35-27-generic #48-Ubuntu SMP x86_64 GNU/Linux mdadm - v2.6.7.1 Does anyone has a suggestion on how to further debug this?

  Read the article

• Why do you use a 3PAR SAN? [closed]

  - by Starfish

  If you use a 3PAR SAN, I’d like to hear what you think about it, particularly compared to the HP EVA. What do you see as its advantages over other SANs like the EVA? What’s so special about the ASIC? We had HP quote us an EVA P6500 and 3PAR V400 with equivalent storage and the 3PAR was nearly twice the cost. My site has two EVA SANs with a combined capacity of ~80 TB. We want to replace the older and larger of the two. We’ve been looking at the EVA and the 3PAR to see which would be a better fit for us. I’m struggling to understand how the 3PAR differs from the EVA from a practical technical standpoint. When I read the sales literature and speak with the HP sales engineers, they spend a lot of time talking about how the 3PAR is better because of its ASIC. It’s ASIC this and ASIC that, but when I press them on how a 3PAR with thin provisioning is better than an EVA with thin provisioning, I can’t get a straight answer. Meanwhile, one of my colleagues, who has more say regarding which SAN we get, is enamored by the 3PAR, and he can’t explain clearly to me why he wants it over the EVA. Our needs are pretty simple. We have 10 servers running VMware and ~100 VMs. We use VMware’s thin provisioning currently, but we would like to start using thin provisioning on the new SAN. We don’t have a need for SSDs or migration between storage tiers. We plan on having FC or SAS drives for our most used data and SATA/FATA drives for the lesser used data which is how we have the EVAs configured. We also do not need any SAN-level snapshotting or replication.

  Read the article

• Should I expect ICMP transit traffic to show up when using debug ip packet with a mask on a Cisco IOS router?

  - by David Bullock

  So I am trying to trace an ICMP conversation between 192.168.100.230/32 an EZVPN interface (Virtual-Access 3) and 192.168.100.20 on BVI4. # sh ip access-lists 199 10 permit icmp 192.168.100.0 0.0.0.255 host 192.168.100.20 20 permit icmp host 192.168.100.20 192.168.100.0 0.0.0.255 # sh debug Generic IP: IP packet debugging is on for access list 199 # sh ip route | incl 192.168.100 192.168.100.0/24 is variably subnetted, 2 subnets, 2 masks C 192.168.100.0/24 is directly connected, BVI4 S 192.168.100.230/32 [1/0] via x.x.x.x, Virtual-Access3 # sh log | inc Buff Buffer logging: level debugging, 2145 messages logged, xml disabled, Log Buffer (16384 bytes): OK, so from my EZVPN client with IP address 192.168.100.230, I ping 192.168.100.20. I know the packet reaches the router across the VPN tunnel, because: policy exists on zp vpn-to-in Zone-pair: vpn-to-in Service-policy inspect : acl-based-policy Class-map: desired-traffic (match-all) Match: access-group name my-acl Inspect Number of Half-open Sessions = 1 Half-open Sessions Session 84DB9D60 (192.168.100.230:8)=>(192.168.100.20:0) icmp SIS_OPENING Created 00:00:05, Last heard 00:00:00 ECHO request Bytes sent (initiator:responder) [64:0] Class-map: class-default (match-any) Match: any Drop 176 packets, 12961 bytes But I get no debug log, and the debugging ACL hasn't matched: # sh log | inc IP: # # sh ip access-lists 198 Extended IP access list 198 10 permit icmp 192.168.100.0 0.0.0.255 host 192.168.100.20 20 permit icmp host 192.168.100.20 192.168.100.0 0.0.0.255 Am I going crazy, or should I not expect to see this debug log? Thanks!

  Read the article

• Avoid "privacy pitfalls" in Windows and Linux?

  - by Somebody still uses you MS-DOS

  I have a Windows and a Linux machine. In Windows, everytime I visit a site, a lot of cache/history files are created on my machine. I setup my Firefox to don't save anything. ...but Windows saves a lot of "temp" files, some strange files I opened in registry (like video names). Each video I open in VLC is shown in "Last shown videos". In windows, all files opened can be found at "Recent opened files" as well. A lot of these privacy configurations can be tweaked (VLC and "Recent opened files" in Windows) - it's a PITA doing it individually, but it's possible - but there isn't a guide to these "internal" privacy traces that are left on Windows installation. In Linux, I just know there are these problems in app level (like VLC). My question is: is there a complete guide to avoid undesirable traces of what I did/watch/used in my Windows machine? (Delete everytime the PC is restarted, or even avoiding recording these info at all) Is there a website with configuration guides to different types of software? I would like to know about Linux privacy pitfalls as well.

  Read the article

• Terminal Server 2008 Login: Access Denied

  - by user1236435

  When I try to RDP into a Server 2008 Terminal Server, I get a message that says "Access Denied" and an OK button. I setup the licensing mode correctly (per user) and also have setup to allow all remote connections. I get the following in the security event log: Log Name: Security Source: Microsoft-Windows-Security-Auditing Date: 28/06/2012 12:01:16 Event ID: 4656 Task Category: File System Level: Information Keywords: Audit Failure User: N/A Computer: 0BraApps1.brenntagLA.hou Description: A handle to an object was requested. Subject: Security ID: BRENNTAGLA\jaadmin Account Name: jaadmin Account Domain: BRENNTAGLA Logon ID: 0xbbe3f Object: Object Server: Security Object Type: File Object Name: C:\Windows\System32\ServerManager.msc Handle ID: 0x0 Process Information: Process ID: 0x60c Process Name: C:\Windows\System32\mmc.exe Access Request Information: Transaction ID: {00000000-0000-0000-0000-000000000000} Accesses: READ_CONTROL SYNCHRONIZE WriteData (or AddFile) AppendData (or AddSubdirectory or CreatePipeInstance) WriteEA ReadAttributes WriteAttributes Access Reasons: READ_CONTROL: Granted by D:(A;;0x1200a9;;;BA) SYNCHRONIZE: Granted by D:(A;;0x1200a9;;;BA) WriteData (or AddFile): Not granted AppendData (or AddSubdirectory or CreatePipeInstance): Not granted WriteEA: Not granted ReadAttributes: Granted by ACE on parent folder D:(A;;0x1301bf;;;BA) WriteAttributes: Not granted Access Mask: 0x120196 Privileges Used for Access Check: - Restricted SID Count: 0 Event Xml: 4656 1 0 12800 0 0x8010000000000000 1535565 Security 0BraApps1.brenntagLA.hou S-1-5-21-205301047-3902605089-2438454170-21511219 jaadmin BRENNTAGLA 0xbbe3f Security File C:\Windows\System32\ServerManager.msc 0x0 {00000000-0000-0000-0000-000000000000} %%1538 %%1541 %%4417 %%4418 %%4420 %%4423 %%4424 %%1538: %%1801 D:(A;;0x1200a9;;;BA) %%1541: %%1801 D:(A;;0x1200a9;;;BA) %%4417: %%1805 %%4418: %%1805 %%4420: %%1805 %%4423: %%1811 D:(A;;0x1301bf;;;BA) %%4424: %%1805 0x120196 - 0 0x60c C:\Windows\System32\mmc.exe Any ideas?

  Read the article

• SQL SERVER 2005 with Windows 7 Problems

  - by azamsharp

  First of all I restored the database from other server and now all the stored procedures are named as [azamsharp].[usp_getlatestposts]. I think [azamsharp] is prefixed since it was the user on the original server. Now, on my local machine this does not run. I don't want the [azamsharp] prefix with all the stored procedures. Also, when I right click on the Sproc I cannot even see the properties option. I am running the SQL SERVER 2005 on Windows 7. UPDATE: The weird thing is that if I access the production database from my machine I can see the properties option. So, there is really something wrong with Windows 7 security. UPDATE 2: When I ran the orphan users stored procedure it showed two users "azamsharp" and "dbo1". I fixed the "azamsharp" user but "dbo1" is not getting fixed. When I run the following script: exec sp_change_users_login 'update_one', 'dbo1', 'dbo1' I get the following error: Msg 15291, Level 16, State 1, Procedure sp_change_users_login, Line 131 Terminating this procedure. The Login name 'dbo1' is absent or invalid.

  Read the article

• How to set up simple VPN for secure Internet connections over unencrypted Wi-Fi on Windows?

  - by Senseful

  I'm looking for a solution similar to the one in this question, except that I don't have a linux computer. I have windows computers that could be set up to accept VPN connections. Preferably I want to set this up on either Windows Server 2003 or Windows XP. I'd like to connect different devices (e.g. iPhone, iPad, laptops, etc.) that are on open unsecure wireless networks (e.g. the one's you see at places like Starbucks) to this VPN to ensure that all my data is secure. I found an article that shows that you can enable VPN connections on Windows XP. After following those steps, though, I'm not sure what to do. Which ports do I open on my firewall? Which VPN settings do I use on my devices such as the iPhone? Do I use L2TP, PPTP, or IPSec? What's the difference between these? Are there any other steps missing in that tutorial? I'm hoping that since Windows has this built in feature, that it will be much simpler to set up rather than having to deal with setting up something such as OpenVPN. If I follow those settings and enable port forwarding on port 1723, and then use the following settings on the iPhone: PPTP (IP Address) RSA SecurID: Off Encryption Level: Auto Send All Traffic: On Proxy: Off It shows "Connecting..." then "Disconnecting..." and the following error message: VPN Configuration A connection could not be established to the PPP server. Try reconnecting. If the problem continues, verify your settings and contact your Administrator. I'm using a user account that I enabled privileges to in the VPN settings on the Windows machine.

  Read the article

• Recommendations for handling Directory Harvesting spam on Exchange 2003

  - by Aaron Alton

  Our Exchange server is getting slammed with anywhere between 450,000 and 700,000 spam messages per day. We receive about 1700 legitimate messages in the same time frame. Roughly 75% of the spam is directory harvesting. We currently have GFI MailEssentials installed. To it's credit, it's doing a very good job, but the sheer volume of spam that we're receiving, and the number of connections that our exchange server is making is preventing legitimate email from being delivered in a timely manner. GFI is set up to check for directory harvesting at the SMTP level, which I presume intercepts the mail before it hits the Exchange services , or goes through SMSE. This "module" is ordered at the top of the list, so (hopefully) dealing with the harvesting is consuming a minimum amount of server resources and bandwidth. My question is, is there anything I can do to prevent our Exchange server's connection pool from being eaten up by these spam hosts? We had to limit the number of concurrent connections being made by Exchange, because it was consuming all of our bandwidth. Thanks, in advance.

  Read the article

• Host name change breaking http? Fedora

  - by Dave

  OK so I have been messing around on my development server. It has been a while since I have had my head in linux and I suspect I have broken something. I have SSH running and that is working fine. I also have HTTP and I had FTP running also. Earlier today I decided I wanted to rename the machine so I updated the /etc/hosts file and /etc/sysconfig/network. I also changed the server name in the httpd.conf. I rebooted the machine and reconnected to SSH fine. Later I was messing around with the FTP service (trying to tighten up the user security) and when i tried to connect remotely to FTP no joy, it said cannot connect. I thought that was weird but had planned to remove ftp as we will be using github so removed ftp and moved on. Then I tried to connect to the website but major fail. even connecting to the IP address is failing. I used lynx to connect to the localhost and there was my site so something going on at server level. I thought maybe something up with iptables but I have not changed them but tried adding http but still no joy. I have a - Fedora release 17 (Beefy Miracle) NAME=Fedora VERSION="17 (Beefy Miracle)" ID=fedora VERSION_ID=17 PRETTY_NAME="Fedora 17 (Beefy Miracle)" ANSI_COLOR="0;34" CPE_NAME="cpe:/o:fedoraproject:fedora:17" Fedora release 17 (Beefy Miracle) Fedora release 17 (Beefy Miracle) Linux version 3.3.4-5.fc17.x86_64 ([email protected]) (gcc version 4.7.0 20120504 (Red Hat 4.7.0-4) (GCC) ) #1 SMP Mon May 7 17:29:34 UTC 2012 This is my iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT icmp -- anywhere anywhere ACCEPT all -- anywhere anywhere ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:ssh REJECT all -- anywhere anywhere reject-with icmp-host-prohibited Chain FORWARD (policy ACCEPT) target prot opt source destination REJECT all -- anywhere anywhere reject-with icmp-host-prohibited Chain OUTPUT (policy ACCEPT) target prot opt source destination Like I say I can use SSH no issue but http although running is a no go from a remote computer. Any ideas?

  Read the article

• How to re-add a RAID-10 failed drive on Ubuntu?

  - by thiesdiggity

  I have a problem that I can't seem to solve. We have a Ubuntu server setup with RAID-10 and two of the drives dropped out of the array. When I try to re-add them using the following command: mdadm --manage --re-add /dev/md2 /dev/sdc1 I get the following error message: mdadm: Cannot open /dev/sdc1: Device or resource busy When I do a "cat /proc/mdstat" I get the following: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [r$ md2 : active raid10 sdb1[0] sdd1[3] 1953519872 blocks 64K chunks 2 near-copies [4/2] [U__U] md1 : active raid1 sda2[0] sdc2[1] 468853696 blocks [2/2] [UU] md0 : active raid1 sda1[0] sdc1[1] 19530688 blocks [2/2] [UU] unused devices: <none> When I run "/sbin/mdadm --detail /dev/md2" I get the following: /dev/md2: Version : 00.90 Creation Time : Mon Sep 5 23:41:13 2011 Raid Level : raid10 Array Size : 1953519872 (1863.02 GiB 2000.40 GB) Used Dev Size : 976759936 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Thu Oct 25 09:25:08 2012 State : active, degraded Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K UUID : c6d87d27:aeefcb2e:d4453e2e:0b7266cb Events : 0.6688691 Number Major Minor RaidDevice State 0 8 17 0 active sync /dev/sdb1 1 0 0 1 removed 2 0 0 2 removed 3 8 49 3 active sync /dev/sdd1 Output of df -h is: Filesystem Size Used Avail Use% Mounted on /dev/md1 441G 2.0G 416G 1% / none 32G 236K 32G 1% /dev tmpfs 32G 0 32G 0% /dev/shm none 32G 112K 32G 1% /var/run none 32G 0 32G 0% /var/lock none 32G 0 32G 0% /lib/init/rw tmpfs 64G 215M 63G 1% /mnt/vmware none 441G 2.0G 416G 1% /var/lib/ureadahead/debugfs /dev/mapper/RAID10VG-RAID10LV 1.8T 139G 1.6T 8% /mnt/RAID10 When I do a "fdisk -l" I can see all the drives needed for the RAID-10. The RAID-10 is part of the /dev/mapper, could that be the reason why the device is coming back as busy? Anyone have any suggestions on what I can try to get the drives back into the array? Any help would be greatly appreciated. Thanks!

  Read the article

• Why is 32-bit-mode required in IIS7.5 for my app?

  - by Jonas Lincoln

  I have a .net4 web application running in a 64 bits 2008 server. I can only get it to run when I set the app pool to Enable 32-bits application to true. All dlls are compiled for .net4 (verified with corflags.exe). How can I figure out why Enable 32-bit is required? The error message from the event log when starting as a 64-bit app-pool Event code: 3008 Event message: A configuration error has occurred. Event time: 2011-03-16 08:55:46 Event time (UTC): 2011-03-16 07:55:46 Event ID: 3c209480ff1c4495bede2e26924be46a Event sequence: 1 Event occurrence: 1 Event detail code: 0 Application information: Application domain: removed Trust level: Full Application Virtual Path: removed Application Path: removed Machine name: NMLABB-EXT01 Process information: Process ID: 4324 Process name: w3wp.exe Account name: removed Exception information: Exception type: ConfigurationErrorsException Exception message: Could not load file or assembly 'System.Data' or one of its dependencies. An attempt was made to load a program with an incorrect format. at System.Web.Configuration.CompilationSection.LoadAssemblyHelper(String assemblyName, Boolean starDirective) at System.Web.Configuration.CompilationSection.LoadAllAssembliesFromAppDomainBinDirectory() at System.Web.Configuration.AssemblyInfo.get_AssemblyInternal() at System.Web.Compilation.BuildManager.GetReferencedAssemblies(CompilationSection compConfig) at System.Web.Compilation.BuildManager.CallPreStartInitMethods() at System.Web.Hosting.HostingEnvironment.Initialize(ApplicationManager appManager, IApplicationHost appHost, IConfigMapPathFactory configMapPathFactory, HostingEnvironmentParameters hostingParameters, PolicyLevel policyLevel, Exception appDomainCreationException) Could not load file or assembly 'System.Data' or one of its dependencies. An attempt was made to load a program with an incorrect format. at System.Reflection.RuntimeAssembly._nLoad(AssemblyName fileName, String codeBase, Evidence assemblySecurity, RuntimeAssembly locationHint, StackCrawlMark& stackMark, Boolean throwOnFileNotFound, Boolean forIntrospection, Boolean suppressSecurityChecks) at System.Reflection.RuntimeAssembly.InternalLoadAssemblyName(AssemblyName assemblyRef, Evidence assemblySecurity, StackCrawlMark& stackMark, Boolean forIntrospection, Boolean suppressSecurityChecks) at System.Reflection.RuntimeAssembly.InternalLoad(String assemblyString, Evidence assemblySecurity, StackCrawlMark& stackMark, Boolean forIntrospection) at System.Reflection.Assembly.Load(String assemblyString) at System.Web.Configuration.CompilationSection.LoadAssemblyHelper(String assemblyName, Boolean starDirective) Request information: Request URL: "our url" Request path: "url" User host address: ip-adddress User: Is authenticated: False Authentication Type: Thread account name: "app-pool" Thread information: Thread ID: 6 Thread account name: "app-pool" Is impersonating: False Stack trace: at System.Web.Configuration.CompilationSection.LoadAssemblyHelper(String assemblyName, Boolean starDirective) at System.Web.Configuration.CompilationSection.LoadAllAssembliesFromAppDomainBinDirectory() at System.Web.Configuration.AssemblyInfo.get_AssemblyInternal() at System.Web.Compilation.BuildManager.GetReferencedAssemblies(CompilationSection compConfig) at System.Web.Compilation.BuildManager.CallPreStartInitMethods() at System.Web.Hosting.HostingEnvironment.Initialize(ApplicationManager appManager, IApplicationHost appHost, IConfigMapPathFactory configMapPathFactory, HostingEnvironmentParameters hostingParameters, PolicyLevel policyLevel, Exception appDomainCreationException) Custom event details:

  Read the article

• Problem routing between directly connected Subnets w/ ASA-5510

  - by Zephyr Pellerin

  This is an issue I've been struggling with for quite some time, with a seemingly simple answer (Aren't all IT problems?). And that is the problem of passing traffic between two directly connected subnets with an ASA While I'm aware that best practice is to have Internet - Firewall - Router, in many cases this isn't possible. For example, In have an ASA with two interfaces, named OutsideNetwork (10.19.200.3/24) and InternalNetwork (10.19.4.254/24). You'd expect Outside to be able to get to, say, 10.19.4.1, or at LEAST 10.19.4.254, but pinging the interface gives only bad news. Result of the command: "ping OutsideNetwork 10.19.4.254" Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.19.4.254, timeout is 2 seconds: ????? Success rate is 0 percent (0/5) Naturally, you'd assume that you could add a static route, to no avail. [ERROR] route Outsidenetwork 10.19.4.0 255.255.255.0 10.19.4.254 1 Cannot add route, connected route exists At this point, you might gander if its a NAT or Access list problem. access-list Outsidenetwork_access_in extended permit ip any any access-list Internalnetwork_access_in extended permit ip any any There is no dynamic nat (or static nat for that matter), and Unnatted traffic is permitted. When I try pinging the above address (10.19.4.254 from Outsidenetwork), I get this error message from level 0 logging (debugging). Routing failed to locate next hop for icmp from NP Identity Ifc:10.19.200.3/0 to Outsidenetwork:10.19.4.1/0 This led me to set same-security traffic permit, and assigned the same, lesser and greater security numbers between the two interfaces. Am I overlooking something obvious? Is there a command to set static routes that are classified higher than connected routes?

  Read the article

• Windows Network File Transfer to Samba server: “Are you sure you want to copy this file without its properties?”

  - by jimp

  I am transferring a lot of files to a new NAS based on OpenMediaVault, with the Samba 3.5.6 service running. I am transferring from Windows 7 64-bit to the NAS, and on some media files Windows is prompting about losing some property data across the transfer. I have never seen this before when transferring to Samba boxes I have built myself (vs this turnkey solution), so I'm guessing there must be a Samba setting I can change to preserve the file properties in question instead of permanently losing whatever they contain (Date Taken? Exposure? Flash Fired? etc). Or maybe I've just never encountered this before; I'm really not sure. I tried adding ea support = yes and store dos attributes = yes to the [global] section, but the problem remains. The Linux file system is ext4 mounted with user_xattr (full options: defaults,acl,user_xattr,noexec,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0) as Samba requires. Any ideas would be greatly appreciated. Thank you! Samba config: [global] workgroup = WORKGROUP server string = %h server include = /etc/samba/dhcp.conf dns proxy = no log level = 2 syslog = 2 log file = /var/log/samba/log.%m max log size = 1000 syslog only = yes panic action = /usr/share/samba/panic-action %d encrypt passwords = true passdb backend = tdbsam obey pam restrictions = yes unix password sync = no passwd program = /usr/bin/passwd %u passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . pam password change = yes socket options = TCP_NODELAY IPTOS_LOWDELAY guest account = nobody load printers = no disable spoolss = yes printing = bsd printcap name = /dev/null unix extensions = yes wide links = no create mask = 0777 directory mask = 0777 use sendfile = no null passwords = no local master = yes time server = yes wins support = yes ea support = yes store dos attributes = yes Note: I found this related question, but it explains the loss due to the user trying to transfer from NTFS to FAT32.

  Read the article

• Backup solution to backup terabytes and lots of static files on linux server?

  - by user28679

  Which backup tool or solution would you use to backup terabytes and lots of files on a production linux server ? Note that the files are all different and almost never modified, and usage is mostly adding files, so data volume is today 3TB growing all the time at around +15GB/day. Please do not reply rsync. Basic unix tools are not enough, rsync does not keep history, rdiff-backup miserably fails from time to time and screw the history. Moreover these are all file based backup, which put a lot of IOwait just to browse directories and query stat(). But i guess, except R1Soft CDP, there is no way around that. We tried R1Soft CDP backup, which is block level backup, and it proved good and efficient for all our other servers, but systematically fails on the server with 3 terabytes and gazillions of files. That is already more than 2 months that the engineers of R1Soft and datacenter are playing a hot ball game... and still no backup except regular rsync We never tried big commercial solutions, except R1Soft CDP since it was provided as an optional service by the datacented hosting our servers.

  Read the article

< Previous Page | 459 460 461 462 463 464 465 466 467 468 469 470  | Next Page >