Search Results

Search found 14780 results on 592 pages for 'low level'.

Page 466/592 | < Previous Page | 462 463 464 465 466 467 468 469 470 471 472 473  | Next Page >

  • windows 7 turns off itself everyday at about 9am

    - by Radek
    I was given this comp at work and after a week or so this strange thing started to happen in the middle of doing something :-( It turns off itself at about 9.10am every morning Just once a day and it works fine after it had it little nap. it happens both if the comp was on all night or I turned it off before leaving the office. I tried to swapped the memory as I was told that there was an issue with memory. But moving or removing any memory did not make any difference. I am not aware that I would install any program that could cause that. I installed AVG and set it up to do every day scan about 8am + if restart is needed it requires user confirmation. 'The Software Protection service has stopped' few minutes before it turned off itself but it happened also at other times without the computer turned off. I turned off Windows automatic updates as the first thing when I got the comp configuration Windows 7 Ultimate Intel Core2 Quad Q9550 at 2.8GH, 8GB RAM ST31000528AS Barracuda 7200.12 SATA 3Gb/s 1TB Update Below message are logged when I turn the comp on again. Message 1: The previous system shutdown at 9:08:54 AM on ?6/?29/?2010 was unexpected. Message 2: Level:Critical Source: Kernel Power EventID 41 Task Category (63) The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. Log after manual restart Update 2 (task scheduler)

    Read the article

  • Distributed storage and computing

    - by Tim van Elteren
    Dear Serverfault community, After researching a number of distributed file systems for deployment in a production environment with the main purpose of performing both batch and real-time distributed computing I've identified the following list as potential candidates, mainly on maturity, license and support: Ceph Lustre GlusterFS HDFS FhGFS MooseFS XtreemFS The key properties that our system should exhibit: an open source, liberally licensed, yet production ready, e.g. a mature, reliable, community and commercially supported solution; ability to run on commodity hardware, preferably be designed for it; provide high availability of the data with the most focus on reads; high scalability, so operation over multiple data centres, possibly on a global scale; removal of single points of failure with the use of replication and distribution of (meta-)data, e.g. provide fault-tolerance. The sensitivity points that were identified, and resulted in the following questions, are: transparency to the processing layer / application with respect to data locality, e.g. know where data is physically located on a server level, mainly for resource allocation and fast processing, high performance, how can this be accomplished? Do you from experience know what solutions provide this transparency and to what extent? posix compliance, or conformance, is mentioned on the wiki pages of most of the above listed solutions. The question here mainly is, how relevant is support for the posix standard? Hadoop for example isn't posix compliant by design, what are the pro's and con's? what about the difference between synchronous and asynchronous opeartion of a distributed file system. Though a synchronous distributed file system has the preference because of reliability it also imposes certain limitations with respect to scalability. What would be, from your expertise, the way to go on this? I'm looking forward to your replies. Thanks in advance! :) With kind regards, Tim van Elteren

    Read the article

  • Why are my Windows 7 updates continuously failing?

    - by Chris C.
    I'm an advanced level user here with an odd issue. I have two Windows Updates that are failing to install, every single time. I'm getting a mysterious "Code 1" error on both updates, an error for which I'm having difficulty finding a solution. The updates in question are: Security Update for Microsoft Visual C++ 2008 Service Pack 1 Redistributable Package (KB2538243) System Update Readiness Tool for Windows 7 for x64-based Systems (KB947821) [May 2011] Because these updates are failing, the Shut Down button in my start menu always has the shield icon next to it, indicating that "new" updates will be installed on shut down. But, of course, they'll fail and when the PC is restarted, the shield icon is still there. When checking the update history and viewing the details of the failed updates, I get the following: Security Update for Microsoft Visual C++ 2008 Service Pack 1 Redistributable Package (KB2538243) Installation date: ?6/?29/?2011 3:00 AM Installation status: Failed Error details: Code 1 Update type: Important A security issue has been identified leading to MFC application vulnerability in DLL planting due to MFC not specifying the full path to system/localization DLLs. You can protect your computer by installing this update from Microsoft. After you install this item, you may have to restart your computer. More information: http://go.microsoft.com/fwlink/?LinkId=216803 and: System Update Readiness Tool for Windows 7 for x64-based Systems (KB947821) [May 2011] Installation date: ?6/?28/?2011 3:00 AM Installation status: Failed Error details: Code 1 Update type: Important This tool is being offered because an inconsistency was found in the Windows servicing store which may prevent the successful installation of future updates, service packs, and software. This tool checks your computer for such inconsistencies and tries to resolve issues if found. More information: http://support.microsoft.com/kb/947821 About My System I'm running Windows 7 Home Premium 64-bit. This is a custom PC build and the OS was installed fresh, not an upgrade from a previous version. I've been running this system for about four months. Windows Updates aside, the system is usually quite stable.

    Read the article

  • Reusing slot numbers in Linux software RAID arrays

    - by thkala
    When a hard disk drive in one of my Linux machines failed, I took the opportunity to migrate from RAID5 to a 6-disk software RAID6 array. At the time of the migration I did not have all 6 drives - more specifically the fourth and fifth (slots 3 and 4) drives were already in use in the originating array, so I created the RAID6 array with a couple of missing devices. I now need to add those drives in those empty slots. Using mdadm --add does result in a proper RAID6 configuration, with one glitch - the new drives are placed in new slots, which results in this /proc/mdstat snippet: ... md0 : active raid6 sde1[7] sdd1[6] sda1[0] sdf1[5] sdc1[2] sdb1[1] 25185536 blocks super 1.0 level 6, 64k chunk, algorithm 2 [6/6] [UUUUUU] ... mdadm -E verifies that the actual slot numbers in the device superblocks are correct, yet the numbers shown in /proc/mdstat are still weird. I would like to fix this glitch, both to satisfy my inner perfectionist and to avoid any potential sources of future confusion in a crisis. Is there a way to specify which slot a new device should occupy in a RAID array? UPDATE: I have verified that the slot number persists in the component device superblock. For the version 1.0 superblocks that I am using that would be the dev_number field as defined in include/linux/raid/md_p.h of the Linux kernel source. I am now considering direct modification of said field to change the slot number - I don't suppose there is some standard way to manipulate the RAID superblock?

    Read the article

  • How can I use wildcards in an Nginx map directive?

    - by Ian Clelland
    I am trying to use Nginx to served cached files produced by a web application, and have spotted a potential problem; that the url-space is wide, and will exceed the Ext3 limit of 32000 subdirectories. I would like to break up the subdirectories, making, say, a two-level filesystem cache. So, where I am currently caching a file at /var/cache/www/arbitrary_directory_name/index.html I would store that instead at something like /var/cache/www/a/r/arbitrary_directory_name/index.html My trouble is that I can't get try_files, or even rewrite to make that mapping. My searching on the subject leads me to believe that I need to do something like this (heavily abbreviated): http { map $request_uri $prefix { /aa* a/a; /ab* a/b; /ac* a/c; ... /zz* z/z; } location / { try_files /var/cache/www/$prefix/$request_uri/index.html @fallback; # or # if (-f /var/cache/www/$prefix/$request_uri/index.html) { # rewrite ^(.*)$ /var/cache/www/$prefix/$1/index.html; # } } } But I can't get the /aa* pattern to match the incoming uri. Without the *, it will match an exact uri, but I can't get it to match just the first two characters. The Nginx documentation suggests that wildcards should be allowed, but I can't see a way to get them to work. Is there a way to do this? Am I missing something simple? Or am I going about this the wrong way?

    Read the article

  • do I need to create an AD site for VPN network

    - by ykyri
    I have Windows Domain level 2008 R2. There are four GC DC in four different physical locations. I have Kerio-based VPN network for replication and remote administration. Here is how network configured: dc1: local IP: 192.168.0.10 VPN IP: 192.168.1.10 dc2: local IP: 10.10.8.11 VPN IP: 192.168.1.11 dc3: local IP: 10.10.9.12 VPN IP: 192.168.1.12 dc4: local IP: 10.10.10.13 VPN IP: 192.168.1.13 That's simple, replication and all works fine but when running dcdiag on dc3 I have an error: A warning event occurred. EventID: 0x000016AF During the past 4.12 hours there have been 216 connections to this Domain Controller from client machines whose IP addresses don't map to any of the existing sites in the enterprise. <...> The log(s) may contain additional unrelated debugging information. To filter out the needed information, please search for lines which contain text 'NO_CLIENT_SITE:'. The first word after this string is the client name and the second word is the client IP address. Here is netlogon.log lines example: 05/30 12:07:39 DOMAIN.NAME: NO_CLIENT_SITE: dc2 192.168.1.11 05/31 09:52:11 DOMAIN.NAME: NO_CLIENT_SITE: dc4 192.168.1.13 05/31 19:49:31 DOMAIN.NAME: NO_CLIENT_SITE: adm-note 192.168.1.101 07/01 05:16:26 DOMAIN.NAME: NO_CLIENT_SITE: dc1 192.168.1.10 All VPN-joined computers are generates same log line as above. Computer amd-note is for example administrator's notebook, also have VPN. Question is should I add new AD site and bind VPN subnet 192.168.1.0/24 with that site?

    Read the article

  • CentOS: Init scripts failing to start for some unknown reason

    - by user705142
    I'm running CentOS 6.2 - I've just migrated some applications over to a failover server, and copied their init scripts into /etc/init.d. I've made them executable, added them to chkconfig, with chkconfig -add, set their levels, made sure they're residing in /etc/rc.d/ - made sure I can execute them from rc2.d etc. The permissions are the same on both servers. They're also running in the same order as on the primary server Yet on reboot they don't start. Any ideas? The offenders are these: jetty 0:off 1:off 2:on 3:on 4:on 5:on 6:off smart 0:off 1:off 2:on 3:on 4:on 5:on 6:off /etc/init.d: -rwxr-xr-x. 1 root root 14456 Mar 13 20:21 jetty -rwxrwxrwx. 1 root root 5829 Mar 29 09:58 smart /etc/rc.d/rc3.d lrwxrwxrwx. 1 root root 15 Mar 29 19:21 S99jetty -> ../init.d/jetty lrwxrwxrwx. 1 root root 11 Mar 26 17:12 S99local -> ../rc.local lrwxrwxrwx. 1 root root 15 Mar 29 19:21 S99smart -> ../init.d/smart I've checked, and I'm in run level 3. I've checked their logs, and there's no indication that that they've been started. I can start them manually easily - and other services are starting normally. I'm completely out of ideas really.

    Read the article

  • Backup data from RAID 1 disk out of its server

    - by Doomsday
    I'm facing with a pretty easy problem in my opinion. I've extracted a working disk from a RAID1 and I'm looking to copy only data (FS and RAID configuration doesn't matter) into another location (another FS). My problem is I'm not able to mount properly this disk into another linux. I've first looked the partition table : # fdisk -l /dev/sdc Disk /dev/sdc: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders, total 1250263728 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdc1 63 1249535699 624767818+ fd Linux raid autodetect /dev/sdc2 1249535700 1250017649 240975 fd Linux raid autodetect /dev/sdc3 1250017650 1250258624 120487+ 82 Linux swap / Solaris I've understood I should use dmraid tools. Once installed : # cat /proc/mdstat Personalities : md0 : inactive sdc1[1](S) 624767744 blocks unused devices: <none> And some other informations : # mdadm --examine /dev/sdc1 /dev/sdc1: Magic : a92b4efc Version : 0.90.00 UUID : 8f292f54:7e5aef72:7e5ab5fd:b348fd05 Creation Time : Mon Jun 2 03:39:41 2008 Raid Level : raid1 Used Dev Size : 624767744 (595.82 GiB 639.76 GB) Array Size : 624767744 (595.82 GiB 639.76 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Update Time : Tue Feb 7 22:34:59 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Checksum : a505b324 - correct Events : 15148 Number Major Minor RaidDevice State this 1 8 1 1 active sync /dev/sda1 0 0 8 17 0 active sync /dev/sdb1 1 1 8 1 1 active sync /dev/sda1 From here, I've tried to mount but I'm not comfortable with dmtools and how it's working. # mount /dev/sdc1 /mnt/sdc1 mount: unknown filesystem type 'linux_raid_member' # mount /dev/md0 /mnt/sdc1 mount: /dev/md0: can't read superblock I've seen some options to alter RAID array with mdadm but I only want to copy data on its filesystem before wiping them... Anyone has a clue ?

    Read the article

  • What is the reason for this DNSSEC validation failure of dnsviz.net?

    - by grifferz
    On trying to resolve dnsviz.net from a host using an Unbound resolver that is configured to use DNSSEC validation, the result is "no servers could be reached": $ dig -t soa dnsviz.net ; <<>> DiG 9.6-ESV-R4 <<>> -t soa dnsviz.net ;; global options: +cmd ;; connection timed out; no servers could be reached Nothing is logged by Unbound to suggest why this is the case. Here is the /etc/unbound/unbound.conf: server: verbosity: 1 interface: 192.168.0.8 interface: 127.0.0.1 interface: ::0 access-control: 0.0.0.0/0 refuse access-control: ::0/0 refuse access-control: 127.0.0.0/8 allow_snoop access-control: 192.168.0.0/16 allow_snoop chroot: "" auto-trust-anchor-file: "/etc/unbound/root.key" val-log-level: 2 python: remote-control: control-enable: yes If I add: module-config: "iterator" (thus disabling DNSSEC validation) then I am able to resolve this host normally. The domain and its DNSSEC check out fine according to http://dnscheck.iis.se/ so there must be something wrong with my resolver configuration. What is it and how do I go about debugging that?

    Read the article

  • IBM BladeCenter S: Disk Configuration

    - by gravyface
    Have just the one storage bay right now (SAS 15K 600GB x 6) and have configured one storage pool in RAID 10 with 4 disks (and two global spares). For each blade, I've created a volume and mapped accordingly: Blade #1 400 GB Blade #2 200 GB Blade #3 100 GB Blade #4 100 GB When I boot up Blade 1 and enter into the UEFI Setup (F1) followed by the Adapters and UEFI Drivers LSI Logic Fusion MPT SAS Driver Utility, I see 4 disks: two are the on-board 73GB drives, the other two are 200GB each and assume I'm being presented with two logical disks from the volume I created and mapped to this blade. I was a bit surprised by this: I figured I would've been presented with one logical drive per volume, not two. I'm assuming I can just configure whatever RAID level I wish that supports two disks, but not really sure what the benefits/trade-offs here. Should I go with RAID 10 on top of RAID 10? RAID 0? Software RAID 0/1/10? Does it even matter? If this is "normal" to see two disks, then I'm going to likely just do some benchmarking and see if it makes a difference changing the RAID levels (my guess is no); if this is not normal, well, please let me know. :)

    Read the article

  • Enter network credentials as part of batch script

    - by Michael
    WinXP: I have several system services that are needed to run some machinery in my lab. The machine these services are running uses a lab login that has administrator rights. Our IS department, unfortunately, has it set up where at some point during the night the login "loses" the privilege level to start/stop these services. The account stays logged in, but the software controlling my hardware becomes unresponsive. In order to get things back up and running, I have to stop the system services and restart them. Because of the security settings, however, I have to re-enter the user password to start the service (even though the user was never logged out). That, I get the "This service cannot be started due to a logon failure" and I have to enter the password. What would be ideal is to have a batch script run before anyone gets into work that stops all of the necessary services, enters the user credentials when prompted, and then restarts them so that everything is ready for first shift to run. I assumed that using the Task Scheduler in Windows would work as it allows you to run batch files with a user's name and password, but this didn't seem to do the trick. With this setup I would arrive to find that all the services are stopped but not started again. (Presumably because the authentication failed.) The batch file is about as simple as it gets, all I have is: net stop "Service1" net stop "Serivce2" etc., then restart in reverse order based on dependency: net start "Service2" net start "Serivce1" What would it take to accomplish what I'm trying to do and restart the services?

    Read the article

  • Server Crash Diagnosis...Are there any 'black box recorder' style programs available.

    - by columbo
    My redhat server is crashing every three weeks or so at 4:15am ish on Sunday mornings. (well it was sundays the last two have been Thursday mornings at 4:15ish) Looking at the logs (mysql, httpd, messages) there are no clues as to why. They just seem to stop. I ran a little script to take memory readings every 15 minutes and it too stops (with normal readings) at this time. The server is remote at a provider so I can only access it via the web. I use Plesk. It appears to be a set job or something that is causing the issue. I can see nothing in crontab. So my question is...has anyone else had this and can offer advice? Failing that. Does any one know of a way to get more detailed logging than that offered by the messages file? I was thinking of a black box style recording program or maybe something as simple as an option somewhere to increase the level of reporting in the messages log. Thanks

    Read the article

  • ext3: maximum recommended partition size / handling large partitions

    - by Hansi
    Hi! I would like to do an encrypted install of Ubuntu on a 2 Terabyte drive (i.e., using LUKS/DMcrypt). In order to not have to type in passwords too often, the partitioning scheme will be 50 GB for / and about 1 TB for /home (and the rest for Windows 7), just for clarity. Even though by now LVM is regarded as being stable, I don't want to bother having more room for errors by introducing unnecessary layers of complexity. For both Ubuntu partitions I want encrypted ext3 with the default blocksize of ext3 (4k?). Thoughts: When I look at most partition schemes here on this site or elsewhere, I usually see at most about 400 or 500 GB partitions (maybe I didn't see enough). There may be different reasons for this, but is reliability an issue here? Are larger ext3 partitions, like about 1 TB, harder to handle for the OS or filesystem driver or at some other level? If I make the partition too large, will it be harder to repair in case of corruptions? Are there some default settings for ext3 that I should change for 1 TB partitions? Question: What maximum partition size for ext3 do you recommend and why? Thanks!

    Read the article

  • Can't access site internally, but DNS works

    - by BloodyIron
    1) I have apache2 running a vhost for a website. 2) This apache2 instance is already successfuly setup for other websites on it to be accessible internally and externally. 3) I am using an internal bind9 server to resolve the new website's domain internally to the private IP. This bind9 server is not public facing, nor is it the master server on the internet. 4) The DNS internally resolves to the right IP. 5) Firefox reports "server not found". 6) I have copied the config almost identically to other configs that are known to work (adjusting for proper paths of course). In turn I have reloaded and restarted apache2 repeatedly. 7) I have an entry to forward .org .info .net alternative TLDs to .com in the vhost config for this domain, and my browser goes from .org to .com despite note #5. 8) /var/log/apache2/access.log shows when someone externally tries to access the site, but no activity is observed when someone tries to access internally. Changing the log level does not appear to improve the situation. 9) I am out of ideas, nothing appears to be wrong. Please help? To be explicit. Why is this new site unreachable internally? I would like to clarify on something, even though I have already outlined this. YES I know this system is in a private network. NO it is not going through a router. YES I am using an internal DNS server (bind9) to resolve, and YES it does resolve to the proper internal IP. YES other websites on the same server setup in the same way with internal resolution work right now and have done for a while. Everything for this domain is setup the same as the other working domains as far as I can tell. The other working domains are internally AND externally accessible. This domain I am working with is only currently externally accessible. When I go to it internally firefox tells me "Server not found".

    Read the article

  • RAID 10 or RAID 5 for multiple VMs - what is the best choice?

    - by Lars Fastrup
    I have just ordered a new rig for my business. We do a lot of software development for Microsoft SharePoint and need the rig to run several virtual machines for development and test purposes. We will be using the free VMware ESXi for virtualization. For a start, we plan to build and start the following VMs - all with Windows Server 2008 R2 x64: Active Directory server MS SQL Server 2008 R2 Automated Build Server SharePoint 2010 Server for hosting our public Web site and our internal Intranet for a few people. The load on this server is going to be quite insignificant. 2xSharePoint 2007 development server 2xSharePoint 2010 development server Beyond that we will need to build several SharePoint farms for testing purposes. These VMs will only be started when needed. The specs of the new rig is: Dell R610 rack server 2xIntel XEON E5620 48GB RAM 6x146GB SAS drives Dell H700 RAID controller We believe the new server is going to make our VMs perform a lot better than our existing setup (2xIntel XEON, 16GB RAM, 2x500 GB SATA in RAID 1). But we are not sure about the RAID level for the new rig. Should we go for having the the 6x146GB SAS drives in a RAID 10 configuration or a RAID 5 configuration? RAID 10 seems to offer better write performance and lower risk of a RAID failure. But it comes at a cost of less drive space. Do we need RAID 10 or would RAID 5 also be a good choice for us?

    Read the article

  • How to restore Active Desktop if Themes is locked via GPO?

    - by pepoluan
    My company forces Active Desktop upon everybody so that it can display a (monthly-rotated) corporate wallpaper.jpg. Problem is, some computers (including my laptop) somehow experienced some errors resulting in the dreaded "Active Desktop Recovery" screen to show up... and clicking the "Restore My Active Desktop" button always resulted in "Internet Explorer Script Error". Various workarounds I found in the Internet either does not work or requires me to change the theme first to something else... and the latter I can't do because the Desktop Settings screen is locked via GPO. As it happens, due to the nature of the programs I use, I'm granted Administrator-level access on my computer. The question is: How do I fix my situation? Note: I don't need to put on my own wallpaper, but watching the "Active Desktop Recovery" screen (with its BLANK WHITE!!1! OH MY EYES!1!!one!eleven!! background) gets tiresome. I'm quite happy with the corporate wallpaper. I just need to somehow 'recover' my Active Desktop. More information: OS: Windows XP Professional SP3 (yeah, company's too afraid to even experiment with Windows 7) Antivirus: Symantec Endpoint Protection If you need any additional information, feel free to ask.

    Read the article

  • Active Directory: Determining DN or OU from log in credentials [closed]

    - by Christopher Broome
    I'm updating a PHP login process to leverage active directory on a Windows server. The logging in process seems pretty straight forward via a "ldap_bind", but I also want to pull some profile information from the AD server (first name, last name, etc...) which seems to require a robust distinguished name (DN). When on the windows server I can grab this via 'dsquery user' on the command prompt, but is there a way to get the same value from just the user's login credentials in PHP? I want to avoid getting a list of hundreds of DNs when on-boarding clients and associating each with one of our users, so any means to programmatically determine this would be preferential. Otherwise, I'll know the domain and host for the request so I can at least set the DC portions of the DN, but the organizational units (OU) seem to be pretty important for querying data. If I can find some of the root level OU values associated with the user I can do a ldap_search and crawl. I browsed through the existing questions and found some similar but nothing that really addressed this, so my apologies if the obvious answer is out there. Thanks for the help.

    Read the article

  • Recommended programming language for linux server management and web ui integration.

    - by Brendan Martens
    I am interested in making an in house web ui to ease some of the management tasks I face with administrating many servers; think Canonical's Landscape. This means doing things like, applying package updates simultaneously across servers, perhaps installing a custom .deb (I use ubuntu/debian.) Reviewing server logs, executing custom scripts, viewing status information for all my servers. I hope to be able to reuse existing command line tools instead of rewriting the exact same operations in a different language myself. I really want to develop something that allows me to continue managing on the ssh level but offers the power of a web interface for easily applying the same infrastructure wide changes. They should not be mutually exclusive. What are some recommended programming languages to use for doing this kind of development and tying it into a web ui? Why do you recommend the language(s) you do? I am not an experienced programmer, but view this as an opportunity to scratch some of my own itches as well as become a better programmer. I do not care specifically if one language is harder than another, but am more interested in picking the best tools for the job from the beginning. Feel free to recommend any existing projects except Landscape (not free,) Ebox (not entirely free, and more than I am looking for,) and webmin (I don't like it, feels clunky and does not integrate well with the "debian way" of maintaining a server, imo.) Thanks for any ideas!

    Read the article

  • DNS manager in Windows Server 2012 Essentials - My one server appears twice

    - by tetranz
    I have a newly installed Windows Server 2012 Essentials. It works pretty good although I'm working on some DNS improvements. Something that seems a little weird is in DNS Manager, my server appears twice. Once as hostname and once as hostname.mydomain.local. They seem to be identical and locked in sync. If I change one, the other follows. Is this normal? Does anyone know why I have this? I'm talking about the top level on the navigation. The very top is DNS and then these two below. Zones, forwarders etc are below them. I've found a couple of forum posts of people asking the same thing but no useful answer. All tutorials etc I can find with screenshots show only one which makes me uncomfortable. The server was installed out of the box as standard with the wizards. I know about the recommendation not to use .local but the wizards didn't give me any other option.

    Read the article

  • RAID degraded on Ubuntu server

    - by reano
    We're having a very weird issue at work. Our Ubuntu server has 6 drives, set up with RAID1 as follows: /dev/md0, consisting of: /dev/sda1 /dev/sdb1 /dev/md1, consisting of: /dev/sda2 /dev/sdb2 /dev/md2, consisting of: /dev/sda3 /dev/sdb3 /dev/md3, consisting of: /dev/sdc1 /dev/sdd1 /dev/md4, consisting of: /dev/sde1 /dev/sdf1 As you can see, md0, md1 and md2 all use the same 2 drives (split into 3 partitions). I also have to note that this is done via ubuntu software raid, not hardware raid. Today, the /md0 RAID1 array shows as degraded - it is missing the /dev/sdb1 drive. But since /dev/sdb1 is only a partition (and /dev/sdb2 and /dev/sdb3 are working fine), it's obviously not the drive that's gone AWOL, it seems the partition itself is missing. How is that even possible? And what could we do to fix it? My output of cat /proc/mdstat: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md1 : active raid1 sda2[0] sdb2[1] 24006528 blocks super 1.2 [2/2] [UU] md2 : active raid1 sda3[0] sdb3[1] 1441268544 blocks super 1.2 [2/2] [UU] md0 : active raid1 sda1[0] 1464710976 blocks super 1.2 [2/1] [U_] md3 : active raid1 sdd1[1] sdc1[0] 2930133824 blocks super 1.2 [2/2] [UU] md4 : active raid1 sdf2[1] sde2[0] 2929939264 blocks super 1.2 [2/2] [UU] unused devices: <none> FYI: I tried the following: mdadm /dev/md0 --add /dev/sdb1 But got this error: mdadm: add new device failed for /dev/sdb1 as 2: Invalid argument Output of mdadm --detail /dev/md0 is: /dev/md0: Version : 1.2 Creation Time : Sat Dec 29 17:09:45 2012 Raid Level : raid1 Array Size : 1464710976 (1396.86 GiB 1499.86 GB) Used Dev Size : 1464710976 (1396.86 GiB 1499.86 GB) Raid Devices : 2 Total Devices : 1 Persistence : Superblock is persistent Update Time : Thu Nov 7 15:55:07 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 0 Spare Devices : 0 Name : lia:0 (local to host lia) UUID : eb302d19:ff70c7bf:401d63af:ed042d59 Events : 26216 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 0 0 1 removed

    Read the article

  • Can a non-redundant RAID5 cause any serious problems (compared to RAID0)?

    - by leemes
    I used to have a three-disc RAID5 (mdadm) in my computer for personal media storage (music, videos, photos, programs, games, ...). It had three discs with 750 GB each, resulting in an array capacity of 1.5 TB. One day (one year ago), I needed one of those discs to install another operating system. I thought, I don't need the redundancy anymore since I backup the most important stuff (personal photos e.g.) on an external disc anyway. So I decided to remove one of the three discs without converting the RAID to RAID0 or even two separate discs, because I had no temporary storage (since one cannot simply convert the RAID5 to RAID0 AFAIK). So now, for about one year, I have a non-redundant RAID5 with 2 of 3 discs running. Sometimes, one of the discs has a defective contact at the power cable or something similar causing the drive to stop working temporarily (I don't know exactly what it is). Since it still works when rebooting the computer and in most cases by calling some mdadm commands, it wasn't that problematic. Note that the data is not very critical, since I still have a backup of the most important stuff. But in the last few weeks, one of the drives fails very frequently (every few hours), so it gets really annoying to manage this. My questions are: Is there any disadvantage (apart from the annoying management) of a non-redundant RAID5 (with one drive less than typical) over a RAID0? If I understand it correctly, both have no redundancy and the same capacity. On a temporary drive failure, I can restart the array in both cases, assuming that the drive itself still works after the failure. Can it happen that the drive contents alter on a drive failure, making the array inconsistent? If so, can I tell mdadm to check the array for failures (without a file system level checking tool)? Since the drive most probably only has a defective contact causing it to fail for a second only, can I tell mdadm to automatically restart the array, so I will not even notice the failure if no application wanted to access the file system during the failure?

    Read the article

  • named responding recursive on norecurse queries

    - by Keks
    I have a server on which named is running. It is intercepted with another named server which it is not aware of. Querying the first named server results in timeouts. The server tries to resolve the query recursively. During that the firewall redirects the DNS Request from the first named server to the second one (the query from the first one is addressed to a e.g. a root server and has its "Recursion desired" bit set to 0). Despite that the second named responds to this request with a entirely or at least 1 level more resolved response than the first named server expects. So it ends up with a timeout even though it got a correct name server or even the full IP for the queried domain. In the first case the first name server tries to follow the authority domain ignoring the coresponding glue record and ends up in a loop it aborts: queried: google.com -> got from named#2: ns1.google.com -> ignore glue record and query: ns1.google.com -> got authority from named#2: google.com In the second case it ignores the answer section with the correct IP and instead tries to follow the name servers from the authority section, which ends up in the same dead end as case 1. So how can it be that the second named responds with recursive results even though the bit was explicitly set to 0 in the request from the first named?

    Read the article

  • How to configure default text selection behavior in Windows XP, 7? (eg. mouse click selects entire word vs. mouse click inserts an active cursor)

    - by Mouse of Fury
    I find the mouse click behavior of Windows XP and Windows 7 annoying and intrusive. I don't remember Windows NT being quite this bad, or MacOS 7 - 10 which I used in the nineties. When I'm using a browser and I click on a text field - for example, the address bar, or a search box - the first thing which happens is the entire field is selected.Subsequent clicks seem to select parts of words, often deciding arbitrarily to exclude or include adjacent punctuation. The same in Excel and other apps, and when trying to rename files, so I'm assuming this behavior comes from a system-wide text handling routine. I frequently want to edit text, cut out or replace odd parts of the insides of words or chunks of sentences, and often find that to get a simple cursor to insert I have to click the mouse up to 4 times in succession. I've had to do a lot of this recently and it has been driving me insane. Is there a place at the system level where this can be configured? In a perfect world, I'd like a single click on a new text area to insert a cursor point, and a rapid double click to select the entire area. Words or text within the area could be selected by inserting a cursor, holding down the mouse button and dragging to the exact point where I want the selection to end - even if that's in the middle of a word. No, I don't need or want Windows to "smart select" a word or sentence for me. I've looked in the Mouse and Accessibility Options control panels (Windows XP). Haven't found anything even close. Thanks -

    Read the article

  • Reliable router with good VPN and WAN Throughput [closed]

    - by Asdande
    I have 2 cisco rv180 VPN router. These routers are giving me lots of problems. The webpages wont load correctly, slow response to load webpages plus other many issues. I have several cases pending with cisco. I give up on these routers. I would like to know if you guys can recommend me a reliable router for our 3 branches (NY - main, SC and FL). In NY- main office, we have 55 users. In SC branch, 6 users. In Florida we only have 1 (will grow soon). I need a router capable of support: 3 VPNs Site-to-Site connection VPN throughput of at least 40-50 Mbps WAN throughput at least 100 Mpbs and up PPTP Server for at least 5 PPTP users Web filtering - all users need access to internet Good Firewall Port forwarding for FTP Server - able to show the public IPs of FTP users (rv180 cannot do that, just shows me router's LAN interface IP, opened a case with cisco, now escaleted to level 2, still no answer or workaround) Dual WAN ports for balance or backup internet. Gigabit WAN/LAN ports Price between $400-$500 range. I was thinking on the TP-LINK TL-ER6120 or TL-ER6020 according to the review on smallnetbuilder.com http://www.smallnetbuilder.com/lanwan/lanwan-reviews/31983-tp-link-tl-er6020-safestream-gigabit-dual-wan-vpn-router-reviewed but I don't want to make another mistake as I did when I bought the cisco RV180. Thank you in advance,

    Read the article

  • Apache Server with memcache, varnish and php slow request times

    - by coolestdude1
    My issue is that these servers are taking rather long for request about 2 seconds on average just to serve files. When we had just one server doing everything it was noticeably faster even with the same web app (Drupal 6 and Drupal 7). I want to get this number down to a reasonable level and so I need some help getting to the bottom of why the request times are so slow. This can cause the webapp to hang on post or put and generally leads to a bad user experience on my sites. PS: I am more of a server newbie so this has confounded me for quite some time. The domains: collabornation.net nptrainingworks.com (they run off the same two webservers using vhost configs) The Gear: Two Rackspace 4 Gig servers running CentOS 6.2 Final They have a mounted file system (gluster) that is used to keep files the same on both machines. They are behind a rackspace load balancer running round robin. Mysql is run using php-pdo and php-mysql as such mysql is run on another instance running memcache on that machine with phpMyAdmin located there as well. Apache version number 2.2.15-15.el6.centos.1 (httpd.x86_64) Varnish version number 3.0.2-1.el5 (varnish.x86_64) PHP version number 5.3.14-1.el6.remi (php.x86_64) Configs Linked Below Apache Conf Vhost Conf Varnish Backends Varnish Defaults Varnish Acl PHP INI Again need some help, much appreciated!

    Read the article

< Previous Page | 462 463 464 465 466 467 468 469 470 471 472 473  | Next Page >