Search Results

Search found 19332 results on 774 pages for 'hard drive'.

Page 470/774 | < Previous Page | 466 467 468 469 470 471 472 473 474 475 476 477  | Next Page >

• Does RAID 1 protect against corruption?

  - by Shaun

  Does Raid 1 protect against data corruption? For example, let's say that I am keeping all of my important files on a NAS that uses 2 disks in a RAID 1. If one hard drive has some kind of internal problem and the data becomes corrupted, does the RAID recognize this automatically and correct it using data from the other good disk? Could it even know which copy is the good one? Does RAID 5 protect against corruption? I know that RAID is not a backup solution. I am trying to figure out how to make sure that I am not backing up corrupt data!

  Read the article

• update ocz vertex le capacity via firmware update

  - by Ben Voigt

  I have an OCZ Vertex LE 100GB drive. It's actually 128GiB of NAND flash, with a whopping 28%+ reserved for write combining. Most 128GiB drives are actually ~ 115GB usable (and marketed as 120GB or 128GB). There were rumors that the reserved fraction could be decreased on OCZ 100GB drives. Can anyone provide a link to firmware that does that, or an official statement that no such firmware exists? (NB: I recently installed the 1.24 firmware from the OCZ site, it didn't affect the capacity. Possibly because the rumors say the capacity change is destructive to existing content.) Of possible interest: flashing firmware was more of a pain than it should have been -- the tool didn't detect the disk until I booted an older Windows install off a secondary hard disk, I suspect the Intel SATA driver is the issue and tool only works with the msachi.sys driver.

  Read the article

• Installing httpssl module on a running NGINX server

  - by Rob

  Hi, New to NGINX, we inherited a project that runs Django/FCGI/NGINX on a hosted RHEL box. A requirement has come in that the site now needs to have ssl enabled. Client was pretty sure the person who had built the site had made it so they could use ssl. I backed up the conf file, added the server block for the ssl instance and tried to reload. Reload failed because it didn't recognize the ssl in this line: ssl on; Not an NGINX expert, but the David Caruso in me tells me that the server (sunglasses on) is not secure. I know that you need to configure NGINX at install with this module. If this didn't happen, how hard/risky is it to reconfigure a running nginx box with this module given that we didn't configure it in the first place.

  Read the article

• Improving TCP performance over a gigabit network lots of connections and high traffic for storage and streaming services

  - by Linux Guy

  I have two servers, Both servers hardware Specification are Processor : Dual Processor RAM : over 128 G.B Hard disk : SSD Hard disk Outging Traffic bandwidth : 3 Gbps network cards speed : 10 Gbps Server A : for Encoding videos Server B : for storage videos andstream videos over web interface like youtube The inbound bandwidth between two servers is 10Gbps , the outbound bandwidth internet bandwidth is 500Mpbs Both servers using public ip addresses in public and private network Both servers transfer and connection on nginx port , and the server B used for streaming media , like youtube stream videos Both servers in same network , when i do ping from Server A to Server B i got high time latency above 1.0ms , the time range time=52.7 ms to time=215.7 ms - This is the output of iftop utility 353Mb 707Mb 1.04Gb 1.38Gb 1.73Gb mqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqq server.example.com => ip.address 6.36Mb 4.31Mb 1.66Mb <= 158Kb 94.8Kb 35.1Kb server.example.com => ip.address 1.23Mb 4.28Mb 1.12Mb <= 17.1Kb 83.5Kb 21.9Kb server.example.com => ip.address 395Kb 3.89Mb 1.07Mb <= 6.09Kb 109Kb 28.6Kb server.example.com => ip.address 4.55Mb 3.83Mb 1.04Mb <= 55.6Kb 45.4Kb 13.0Kb server.example.com => ip.address 649Kb 3.38Mb 1.47Mb <= 9.00Kb 38.7Kb 16.7Kb server.example.com => ip.address 5.00Mb 3.32Mb 1.80Mb <= 65.7Kb 55.1Kb 29.4Kb server.example.com => ip.address 387Kb 3.13Mb 1.06Mb <= 18.4Kb 39.9Kb 15.0Kb server.example.com => ip.address 3.27Mb 3.11Mb 1.01Mb <= 81.2Kb 64.5Kb 20.9Kb server.example.com => ip.address 1.75Mb 3.08Mb 2.72Mb <= 16.6Kb 35.6Kb 32.5Kb server.example.com => ip.address 1.75Mb 2.90Mb 2.79Mb <= 22.4Kb 32.6Kb 35.6Kb server.example.com => ip.address 3.03Mb 2.78Mb 1.82Mb <= 26.6Kb 27.4Kb 20.2Kb server.example.com => ip.address 2.26Mb 2.66Mb 1.36Mb <= 51.7Kb 49.1Kb 24.4Kb server.example.com => ip.address 586Kb 2.50Mb 1.03Mb <= 4.17Kb 26.1Kb 10.7Kb server.example.com => ip.address 2.42Mb 2.49Mb 2.44Mb <= 31.6Kb 29.7Kb 29.9Kb server.example.com => ip.address 2.41Mb 2.46Mb 2.41Mb <= 26.4Kb 24.5Kb 23.8Kb server.example.com => ip.address 2.37Mb 2.39Mb 2.40Mb <= 28.9Kb 27.0Kb 28.5Kb server.example.com => ip.address 525Kb 2.20Mb 1.05Mb <= 7.03Kb 26.0Kb 12.8Kb qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq TX: cum: 102GB peak: 1.65Gb rates: 1.46Gb 1.44Gb 1.48Gb RX: 1.31GB 24.3Mb 19.5Mb 18.9Mb 20.0Mb TOTAL: 103GB 1.67Gb 1.48Gb 1.46Gb 1.50Gb I check the transfer speed using iperf utility From Server A to Server B # iperf -c 0.0.0.2 -p 8777 ------------------------------------------------------------ Client connecting to 0.0.0.2, TCP port 8777 TCP window size: 85.3 KByte (default) ------------------------------------------------------------ [ 3] local 0.0.0.1 port 38895 connected with 0.0.0.2 port 8777 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.8 sec 528 KBytes 399 Kbits/sec My Current Connections in Server B # netstat -an|grep ":8777"|awk '/tcp/ {print $6}'|sort -nr| uniq -c 2072 TIME_WAIT 28 SYN_RECV 1 LISTEN 189 LAST_ACK 139 FIN_WAIT2 373 FIN_WAIT1 3381 ESTABLISHED 34 CLOSING Server A Network Card Information Settings for eth0: Supported ports: [ TP ] Supported link modes: 100baseT/Full 1000baseT/Full 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 10000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 0 Transceiver: external Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes Server B Network Card Information Settings for eth2: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: Direct Attach Copper PHYAD: 0 Transceiver: external Auto-negotiation: off Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes ifconfig server A eth0 Link encap:Ethernet HWaddr 00:25:90:ED:9E:AA inet addr:0.0.0.1 Bcast:0.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1202795665 errors:0 dropped:64334 overruns:0 frame:0 TX packets:2313161968 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:893413096188 (832.0 GiB) TX bytes:3360949570454 (3.0 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2207544 errors:0 dropped:0 overruns:0 frame:0 TX packets:2207544 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:247769175 (236.2 MiB) TX bytes:247769175 (236.2 MiB) ifconfig Server B eth2 Link encap:Ethernet HWaddr 00:25:90:82:C4:FE inet addr:0.0.0.2 Bcast:0.0.0.2 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:39973046980 errors:0 dropped:1828387600 overruns:0 frame:0 TX packets:69618752480 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3013976063688 (2.7 TiB) TX bytes:102250230803933 (92.9 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:1049495 errors:0 dropped:0 overruns:0 frame:0 TX packets:1049495 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:129012422 (123.0 MiB) TX bytes:129012422 (123.0 MiB) Netstat -i on Server B # netstat -i Kernel Interface table Iface MTU Met RX-OK RX-ERR RX-DRP RX-OVR TX-OK TX-ERR TX-DRP TX-OVR Flg eth2 9000 0 42098629968 0 2131223717 0 73698797854 0 0 0 BMRU lo 65536 0 1077908 0 0 0 1077908 0 0 0 LRU I Turn up send/receive buffers on the network card to 2048 and problem still persist I increase the MTU for server A and problem still persist and i increase the MTU for server B for better connectivity and transfer speed but it couldn't transfer at all The problem is : as you can see from iperf utility, the transfer speed from server A to server B slow when i restart network service in server B the transfer in server A at full speed, after 2 minutes , it's getting slow How could i troubleshoot slow speed issue and fix it in server B ? Notice : if there any other commands i should execute in servers for more information, so it might help resolve the problem , let me know in comments

  Read the article

• mac osx script - find mounted disc with name, copy file from desktop to it, when copy complete, unmount disc

  - by Joshc

  Is there some kind of mac script which finds a newly mounted disc drive that has the name 'EXAMPLE', then copies a file/folder to it and safely ejects the disc when copy has finished? I don't mind if the script needs to be executed by a short cut. And will it work if there are multiple drives plugged in? The reason I am asking is becuase i have 5000 usb memory sticks that I need to copy about 20mb worth of data to it. Thanks in advance for any ideas.

  Read the article

• import macintosh thunderbird emails to windows email

  - by Ryan

  My mac laptop died. The hard drive is good. I am able to pull what I need off my mac and copy it to windows using an open source tool (I forgot the name of it). I need my old mac emails. I was using the macintosh thunderbird for emails. How do I load those emails into thunderbird, outlook, or any other windows email tool? I did google this and there were some brief explanations, but they did not work. The vast majority of posts are about going from windows to mac.

  Read the article

• Hearing repeated sound in Linux mint Chrome Browser

  - by aravind.udayashankara

  I am using Linux mint OS since an Year , I use to consistently download updates and install , I use chrome as a default browser , when ever I open youtube and watch some video , I listen to some repetition in sound ( say repeated lyrics of song ) while it is playing , In firefox it is working fine . What is the problem am I missing any plugin , AFAIK Chrome doesn't need a flash player plug in , It has a built in flash player . IS that the problem ? And also previously I was not facing this , recently I started using Cinimon UI centOS after this all these kind of problems started MY hard ware is 64 bit intel core i3 and also I have installed linux mint 64 bit Please let me know what is the problem and how to fix this . Thanks in advance for responding to this post

  Read the article

• How do I burn Xubuntu Live CD

  - by Julian

  I downloaded the 600+ MB Xubunto ISO. Burnt it to a DVD using Nero Burning Rom, as a Bootable DVD. My bootup sequence won't detect XUbuntu and still only detects windows on my Hard Drive even after I set my BIOS to boot from the CDROM first. How do I burn the Live CD with Nero? I'm thinking maybe I should extract the contents and then burn the folder as data to my DVD. P.S: I only have DVDs lying around.

  Read the article

• Less reboots on Windows Server Core, is this true or just a myth?

  - by Peter Hahndorf

  Because there are less components installed on a Windows Server core OS, it needs less patches than the full OS. I read in several places that therefor it needs less reboots after patching. I'm running Server 2012 core in production since September 2012 now and I don't remember a single patch-Tuesday when I did not have to reboot the server after installing Windows updates. Are there any hard numbers out there that compare the required reboots for core vs. Full OS? Less reboots may be the main reason why people choose to go with Server core. If it actually requires just as many reboots as the full OS install, they may think again the next time they set up a server.

  Read the article

• UDF filesystem -> Maximum number of files

  - by user978122

  I am considering partitioning a rather large hard drive with the UDF filesystem for an experiment, and would like to ask if anyone knows the maximum number of files, either by directory, or as a whole, that the UDF filesystem can handle? For some background, I looked at the JFS and XFS filesystems (NTFS has a limitation of the number of files per volume); however, since I run Windows, that's kind of out. UFD, on the other hand, does not appear to have these limitations, but then, I cannot really find any information on just how many files per volume the UDF file system supports.

  Read the article

• Cannot find the 2nd datastore after upgrading ESXi 3.5

  - by aXqd

  I have an ESXi server (version 3.5) with about 60 VMs. It has 2 hard disks, each of which is regarded as a datastore. After upgrading through 'VMware Infrastructure Update' tool(still staying with 3.5 instead of 4.0) and a reboot, I can only see the 1st datastore. Hence many VMs are, now, inaccessible. I wonder how I can get the 2nd datastore back. I am sorry, but I did't have the 2nd datastore backuped before. BTW, I am still thinking of upgrading directly to version 4.0 to see if it can fix the driver problem. How about that?

  Read the article

• Is there anything like a link or shared mount point for FAT32 folders in Linux/Android?

  - by endolith

  I often want the same files to be accessed by different apps on my Android phone, but the apps look in different folders. Is there a way to make two different folder paths on a FAT SD card point to the same file? For EXT, I think I could do this with a symbolic or hard link, but those don't exist for FAT. Can FAT be extended to support them? Can Android use an EXT-formatted SD card? Can a folder be mounted on top of another folder? If this does exist, does it have any negative side effects?

  Read the article

• TeamViewer: How to disable color dithering for low-bit-depth screen settings

  - by gogowitsch

  I am using Terminal Services and TeamViewer a lot to access other computers, partly over slow networks. The problem described below is not affected by which of the two remote access services I am using. When accessing Windows 7 Professional machines, a great deal of text is hard to read as the background is dithered. Even for exactly the same colors, Windows 2003 does not seem to dither at all, but to choose the closest available color. I strongly prefer the latter, as I don't care for the exact colors, I just want to be able to read easily. I am not sure whether this is operating system-related. The programs on the remote systems do not allow me to change the color choices for the various backgrounds to anything sane. Is there a way to disable this color dithering using some target operating system setting that will do the trick for both Terminal Services and TeamViewer?

  Read the article

• Auto-resize images in Opera

  - by Nick

  Is there a setting that I can configure to automatically scale large images like Firefox does? I'm using Opera 10.53, and when I open a large image in a new tab, it is not scaled at all. I'm on a laptop, so it is hard to view, and when I am viewing multiple images, it is tedious to scale each image down to 20% or whatever fits it best. I found this thread, and for a fleeting moment thought I had found the answer, but apparently not. They just told the poster to manually resize. Thanks.

  Read the article

• Collect and Backup Photos from Multiple Photographers

  - by Graviton

  I have a few photographers working under me ( well, not exactly under me, but I say it anyway just for illustration purpose), so they shoot a lot of photos, the problem is that they all store their photos on their hard disk, and I have no way to retrieve them unless I pass them an USB and ask them to fill it with their photos. Very labor intensive and inefficient! Is there any other better ( more automated) ways of doing this? For the fear of losing the resolution, I don't really favor a online-synch approach, because I think all the photos uploaded to any website will suffer a resolution loss, which is the last thing I want. Is there a better idea? Edit: Being artistic as they are, I can't guarantee that they all use PC and Windows; so the software must at least be able to run on Mac.

  Read the article

• Iptables mark incoming packet - vpn routing

  - by Tom

  I have connected my home to my workplace for out of house backup reasons through openvpn. The connection is working nicely. At work I have 5 fixed IP addresses. Now I would like to assign one of these IP addresses to be forwarded to my home machine. I have confirmed packet arrival at my home machine with tcpdump. The problem is that my default route at home is NOT the tun0 (naturally), but eth0 to my own ISP. So I created a separate routing table to route my tun0 packets back to where they belong, but do not how to mark the incoming packet which arrive through tun0 with iptables, so I can drive them back. I do not want any port restrictions, but only what comes from tun0 should leave through tun0 thanks tom

  Read the article

• How to access Windows Registry from DOS

  - by SEARAS

  How to access Windows Registry from DOS? I need to access registry from DOS, while I boot from DOS bootable disk. I've searched all the internet, and found only Offline NT Password and Registry Editor, which can not be used in DOS, as I understand. Also I've found RegView (from many mirrors), which isn't working too (I've tried many instructions). Is there any easy-in-usage tool, like reg.exe, which is able to load registry hives, so that I can change registry values?? Or any working instructions ?? Note: I already have a bootable drive, which can read/write to NTFS drives. Thanks in advance!

  Read the article

• System says memory controller not available and doesn't boot?

  - by Martin

  Hello everybody, Recently I have had a MainBoard-problem. I've send my mainboard to service and today I got it back from the company. It is a Foxconn 520a mainboard. Now I have installed my exchanged mainboard. But now I have a problem. My system boots until the device list with IRQ entries appear. The system says "Verifying DMI-pool-data..." and nothing happens. The IRQ-device list shows that the memory-controller is not available. All other devices have got an IRQ. Bus No. Device No. Func No. Vendor/Device Class Device Class IRQ 0 0 0 10DE 0547 0500 Memory Controller NA Do you have any ideas where the problem could be? I already have disconnected all unnecessary devices like the hard disks. Perhaps it is a BIOS problem, but I don't know where I should look. Would be nice if there is any advice, Greetings, Martin

  Read the article

• Minimum space required for Server 2008 R1 install?

  - by Chris J

  I'm trying to plan disk space for a virtual environment, and wanting to keep virtual disks as small as possible - mostly as apart from the base OS, the software going onto the VM is less than a few MB, so want to avoid physical disk space going to waste; plus it'll give me an idea of how many VMs I could physically fit in {x}GB of physical drive. For Server 2003, I've had installs on 2GB and 5GB sized virtual disks. However for Server 2008, Microsoft recommends a minimum of 10GB (I assume this is both for x32 and x64). For the record, I will be installing the x32 version. Now I know I could just go ahead and try a small install, but wanted to solicit any practical knowledge as well :-) What's the smallest install of Server 2008 possible? (excluding server core installations).

  Read the article

• Best Small Linux Distribution for rDesktop

  - by d2jxp

  What would be the best linux distribution to use just for the purpose of rDesktop? We're trying to decide if we should get rid of old computers or just use them as thin-clients to connect to virtual Windows 7 machines on our network. I would like something with as little bloat as possible and can be run from a USB flash drive. I have tried SliTaz, ThinStation, and Pixil from Century Software. SliTaz has been my favorite so far but I still want to know if there's something better that's also easily customizable.

  Read the article

• Windows 7 sata disk not recognized after wake up from sleep state

  - by Gabber

  My windows 7 x64 PC/server worked fine until I installed a brand new seagate SATA hard disk (2 TB). My first disk was a IDE Maxtor (250 GB). I tried to use it as a secondary drive leaving the maxtor as primary and, when I put the computer in sleep state, on wake-up the SATA disk is not recognized anymore until next reboot. Now I'm trying to set it as primary disk (I copied the old HD contents with HD clone), when the computer goes in sleep state, on wake up it doesn't see the disc thus causing my system to crash. I tried the following: BIOS update (Asus M2V motherboard) but the situation worsened as the system didn't wake up from the sleep (with both my HD's) Reinstalling the drivers Bios changes Microsoft Hotfix KB977178 that seemed to address exactly my problem but gave me "The update is not applicable to your computer" message. Disabling hybrid sleep but no results. I also tried all the suggestions from this question Why doesn't Windows 7 wake up from sleep?. Still no results.

  Read the article

• What are those white circles on the desktop in Gnome 3?

  - by monk

  I have Fedora 20 with GNOME 3.10.2. On the desktop background (i.e. where the wallpaper is), there are five small white circles centered at the very bottom of the screen. The first is filled, the others are not. I can click those circles, thereby changing which one is filled, like a radio button. I cannot for the life of me figure out what those circles are supposed to do, and it's starting to drive me crazy. Clicking and thus changing which circle is filled does nothing I can perceive, and there seems to be no configuration option anywhere that has anything to do with them. What are those things? Is there any way to get rid of them? Edit: I made a screenshot of my desktop with no programs running. You can see the dot/circle thingies at the bottom. Link: http://www.imageupload.co.uk/images/2014/08/18/Screenshot_from_2014-08-18_235427.png

  Read the article

• mounts aren't case-sensitive

  - by Asi

  I mounted a few drives from Linux boxes in my network, but those mounts aren't case-sensitive. The mount command I used ( from the man mount.cifs, case-sensitive should be the default ): mount //10.0.1.10/remote_folder /local_folder -t cifs -o username=xxxx,password=xxxx but those mounts aren't sensitive. for example doing: ls -l /local_folder/testfile.txt ls -l /local_folder/TESTFILE.TXT give's the same result... instead of 'file not found' Couple of important points: All drives are running on Linux machines. My local machine is running Fedora 18 and it is case-sensitive for ANY folder/file expect the mounted drives. All drive/mounts are case-sensitive when when doing SSH. So if I SSH from my local machine to a remote machine, doing ls -l /local_folder/TESTFILE.TXT will say file not found as it should. So I believe the issue is in my local machine and not in the way I did the mount. but I'm not sure where to look next (I'm new to Linux)

  Read the article

• Windows 7 sata disk not recognized after wake up from sleep state [closed]

  - by Gabber

  My windows 7 x64 PC/server worked fine until I installed a brand new seagate SATA hard disk (2 TB). My first disk was a IDE Maxtor (250 GB). I tried to use it as a secondary drive leaving the maxtor as primary and, when I put the computer in sleep state, on wake-up the SATA disk is not recognized anymore until next reboot. Now I'm trying to set it as primary disk (I copied the old HD contents with HD clone), when the computer goes in sleep state, on wake up it doesn't see the disc thus causing my system to crash. I tried the following: BIOS update (Asus M2V motherboard) but the situation worsened as the system didn't wake up from the sleep (with both my HD's) Reinstalling the drivers Bios changes Microsoft Hotfix KB977178 that seemed to address exactly my problem but gave me "The update is not applicable to your computer" message. Disabling hybrid sleep but no results.

  Read the article

• Microsoft Outlook: show multi-day appointments as boxes in calendar day and week view

  - by Bernd

  I would like to show appointments spanning several days the same way as appintments within a single day. Single day appointments are shown with a white or colored box, covering the day horizontally. Multi-day appointments are shown in the day/week header and are indicated blue or purple on the left side of a day. This happens even if a multi-day appointment is not an all-day appointment (i.e. checkbox is off) and I have a start and end time. I frequently have a hard time seeing appointment overlaps wenn acceping single day appointments. Therefore I am looking for multi-day appointments shown the same way as single day appointments. I am on Outlook 2003.

  Read the article

< Previous Page | 466 467 468 469 470 471 472 473 474 475 476 477  | Next Page >