Search Results

Search found 13995 results on 560 pages for 'home'.

Page 470/560 | < Previous Page | 466 467 468 469 470 471 472 473 474 475 476 477  | Next Page >

• How can I make IPv6 on OpenVPN work using a tap device?

  - by Lekensteyn

  I've managed to setup OpenVPN for full IPv4 connectivity using tap0. Now I want to do the same for IPv6. Addresses and network setup (note that my real prefix is replaced by 2001:db8): 2001:db8::100:0:0/96 my assigned IPv6 range 2001:db8::100:abc:0/112 OpenVPN IPv6 range 2001:db8::100:abc:1 tap0 server side (set as gateway on client) 2001:db8::100:abc:2 tap0 client side 2001:db8::1:2:3:4 gateway for server Home laptop (tap0: 2001:db8::100:abc:2/112 gateway 2001:db8::100:abc:1/112) | | | (running Kubuntu 10.10; OpenVPN 2.1.0-3ubuntu1) | wifi | | router | | OpenVPN INTERNET | eth0 | /tap0 VPS (eth0:2001:db8::1:2:3:4/64 gateway 2001:db8::1) (tap0: 2001:db8::100:abc:1/112) (running Debian 6; OpenVPN 2.1.3-2) The server has both native IPv4 and IPv6 connectivity, the client has only IPv4. I can ping6 to and from my server over OpenVPN, but not to other machines (for example, ipv6.google.com). Using tcpdump on both the server and client, I can see that packets are actually transferred over tap0 to eth0. The router (2001:db8::1) send a neighbor solicitation for the client (2001:db8::100:abc:2) to eth0 after it receives the ICMP6 echo-request. The server does not respond to that solicitation, which causes the ICMP6 echo-request not be routed to the destination. How can I make this IPv6 connection work?

  Read the article

• Can't access Port 80 from external

  - by dewacorp.alliances

  Hi there I have configuration like this: NETGEAR MODEM LINKSYS ROUTER SERVERS In the modem, I've setup as bridging and all the traffic is controlling by this ROUTER. Prior to this setup, I can access website from external (port 80) plus exchange servers (mail) and https. But now with this configuration, I can only send/receive using Exhcange servers and access OWA (Outlook web access using port 443) .... and no internal websites from outside. This is my config for LINKSYS ROUTER Application | Start | End | Protocol | IP Address Ms Exchange | 25 | 25 | Both (TCP/UDP) | 192.168.100.8 Internets | 80 | 80 | Both (TCP/UDP) | 192.168.100.11 SSL | 443 | 443 | Both (TCP/UDP) | 192.168.100.8 Exchange | 110 | 110 | Both (TCP/UDP) | 192.168.100.8 192.168.100.11 is a UBUNTU web server that running the apache which controlling the virtual name (extranet, cms, test) to redirect to the different servers. As you can see, the home internet is only allowing public IP address. Now I test this schenarion in internal network work nicely. For instance. If I type in extranet.XXX.local it goes to the right applicatios or if I try CMS.XXX.local again it goes to the right one. I also asked to ISP just in case if they are blocking the inbound port 80 for unknown reason. They said no. So I didn't understand why this happens. I suspect the configuration that I have between MODEM ROUTER but I counldn't work what it is. I don't have a documentation of previous settings and I don't know if there is a port that I need to open as well. I am appreciated your comment

  Read the article

• What is going on when I can't access an SMB server share (not accessible error) until I run cmdkey to delete the credential?

  - by Warren P

  I have a network connection share issue. The first connection works, and seems to stay connected for at least a few hours. However, after each time my windows 7 PC reboots, it can no longer form a network connection to the shared folder, nor browse to it, until I not only unmap and remap the mapped drive, but also, I have to use cmdkey to delete the stored credentials like this: cmdkey /delete:Domain:target=HOSTNAME My work PC is on a domain, and I am not the IT administrator, but I'm curious if there is anything I can do to investigate this issue. Any settings in registry or group policy that I could examine to see why the first connection works, but each subsequent attempt (once a stored credential exists) to browse or use the connection, fails with a connection error saying it is "not accessible", like this: I do not even get any error until at least several minutes go by. THe first thing I see is a window frozen and empty, and then I get this error: This has happened when connecting to a share on a DROBO device, and on a share which is not on the domain, but which was a Microsoft Home Server. I wonder if there's something broken in WIndows 7 professional with regards to connecting to non-domain shares when an active directory domain controller exists, and a particular workstation is joined to a domain? The problem only occurs if I click "remember credentials". It is not fixed by any amount of working with net use. Usingcmdkey to delete all stored credentials for the host is the only way to get back in, and it affects all non-domain shared folders. Update I'm hoping there are some registry locations I could check that could be misconfigured in some way that might explain why SMB/CIFS stored credentials for non-domain systems seem to be auto-invalidated in this weird way. Knowing how whacko Microsoft Windows domain and security handling is sometimes, this could be some kind of stupid "feature".

  Read the article

• Using Samba to share a folder from a Linux guest with a Windows host in VirtualBox

  - by AmV

  I would like to share a folder from a Linux Guest with a Windows host (with read and write access if possible) in VirtualBox. I read in these two links: here and here that it's possible to do this using Samba, but I am a little bit lost and I need more information on how to proceed. So far, I managed to set up two network adapters (one NAT and one host-only) and install Samba on the Linux guest, but now I have the following questions: What do I need to type in samba.conf to share a folder from the Linux guest? (the tutorial provided in one of the links above only explains how to share home directories) Are there any Samba commands that need to be executed on the guest to enable sharing? How do I make sure that these folders are only available to the host OS and not on the Internet? Once the Linux guest is setup, how do I access each of the individual shared folders from the Windows host? I read that I need to mount a drive on Windows to do this, but do I use Samba logins, or Linux logins, also do I use localhost? or do I need to set up an IP for this? Thanks!

  Read the article

• Replacing DropBox with: Amazon S3 + SSL + GPG/TrueCrypt + Mounting on OSX ??

  - by Matt Rogish

  So, right now we're using DropBox to share various data files around between approximately 10 Mac OS X systems. However, we already have an S3 account and everyone on the lowest DropBox plan of $10/mo seems too expensive. So, I am contemplating something that would allow us to replace DropBox with our own home-grown solution. We are all fairly technical people and/or smart enough to follow some steps, so if it's not as "user friendly" as DropBox we're all comfortable with that. There are plenty of docs out there that have bits and pieces of what I want but some of the tools don't seem to fit the requirements: Transport security via SSL to the bucket Encryption of bucket contents Bi-directional syncing Most of the scripts I can find on the internet use "duplicity" which appears to fail #1 (it doesn't look like duplicity supports SSL to S3 - the docs don't state but the protocol looks plain old http http://www.nongnu.org/duplicity/duplicity.1.html#sect6 ) Many scripts use gpg to encrypt files. This seems like it could work, however I have to make sure that each OSX client is able to use the same key to encrypt and decrypt files (key management is left to me to manage). Finally, most of the scripts use one-way replication, e.g. using Amazon S3 as a simple backup store. As we'd be using Amazon S3 as the "repository" they fail this one. Whew. So, I'd love a single tool that does this but after an exhaustive search I don't think one exists. I'd be happy just knowing which tools out there can fulfill my 3 requirements, after that I can stitch together the rest. Any thoughts? THANKS!

  Read the article

• Why are my Windows 7 updates continuously failing?

  - by Chris C.

  I'm an advanced level user here with an odd issue. I have two Windows Updates that are failing to install, every single time. I'm getting a mysterious "Code 1" error on both updates, an error for which I'm having difficulty finding a solution. The updates in question are: Security Update for Microsoft Visual C++ 2008 Service Pack 1 Redistributable Package (KB2538243) System Update Readiness Tool for Windows 7 for x64-based Systems (KB947821) [May 2011] Because these updates are failing, the Shut Down button in my start menu always has the shield icon next to it, indicating that "new" updates will be installed on shut down. But, of course, they'll fail and when the PC is restarted, the shield icon is still there. When checking the update history and viewing the details of the failed updates, I get the following: Security Update for Microsoft Visual C++ 2008 Service Pack 1 Redistributable Package (KB2538243) Installation date: ?6/?29/?2011 3:00 AM Installation status: Failed Error details: Code 1 Update type: Important A security issue has been identified leading to MFC application vulnerability in DLL planting due to MFC not specifying the full path to system/localization DLLs. You can protect your computer by installing this update from Microsoft. After you install this item, you may have to restart your computer. More information: http://go.microsoft.com/fwlink/?LinkId=216803 and: System Update Readiness Tool for Windows 7 for x64-based Systems (KB947821) [May 2011] Installation date: ?6/?28/?2011 3:00 AM Installation status: Failed Error details: Code 1 Update type: Important This tool is being offered because an inconsistency was found in the Windows servicing store which may prevent the successful installation of future updates, service packs, and software. This tool checks your computer for such inconsistencies and tries to resolve issues if found. More information: http://support.microsoft.com/kb/947821 About My System I'm running Windows 7 Home Premium 64-bit. This is a custom PC build and the OS was installed fresh, not an upgrade from a previous version. I've been running this system for about four months. Windows Updates aside, the system is usually quite stable.

  Read the article

• XenServer 5.5 running WHS.. trying to add local or network printer/scanner/copier

  - by ProstheticHead

  Hi guys. Just wondering if anyone has prior experience in sharing a multifunction printer across a (mostly windows) network? My situation at the minute is complicated.. I DID have the printer attached directly to a Windows Home Server box and was able to scan to a share and print across the network from my other computers. Compatibility problems have forced me to virtualize WHS on XenServer 5.5... This is actually quite useful because I can now run other things on the same box, but the problem is that now WHS doesn't get direct hardware access so it doesn't see a USB attached PSC... Grrrr! So now I have a choice to make. I've read somewhere that I can buy an add in PCI USB controller and somehow set up a passthrough to one VM at a time. To me, this sound complicated but if it's likely to work reliably I'd prefer this method. I've read about another approach, which I'm not sure about either, but I guess sounds plausible. A Network USB server, (NOT a print server) that can somehow make a USB port accessible across a network. My worry here is that it likely needs some kind of 3rd party software to work.. so not ideal. If there are any other methods you can suggest I'd be happy to hear them... I need your help guys. I'm also in the market for a PCI express SATA controller, nothing flashy, just need up to 8 ports, JBOD and 100% compatability.. Any suggestions? Regards Kevin

  Read the article

• Wordpress Forbidden page

  - by ffffff

  HTML without a body part is null If I read preview mode in (there is no authority) without logging in The response html is this.. <html xmlns="http://www.w3.org/1999/xhtml" lang="ja" xml:lang="ja"> <head profile="http://purl.org/net/ns/metaprof"> <meta http-equiv="Content-Type" content="text/html; charset=UTF-8" /> <meta http-equiv="Content-Script-Type" content="text/javascript" /> <meta name="generator" content="WordPress 2.9.2" /> <meta name="author" content="blog" /> <link rel="alternate" type="application/atom+xml" href="http://blog.example.com/feed/atom/" title="Atom cite contents" /> <link rel="start" href="http://blog.example.com" title="blog Home" /> <link rel="stylesheet" type="text/css" href="http://blog.example.com/wp-content/themes/blog/style.css" /> <meta name="description" content="blog" /> <title>blog - </title> </head> <body class="individual single"> </div> </body> </html> Do you have any solutions?

  Read the article

• What is the quickest and safest way to test new software and revert all changes, if needed?

  - by calbar

  I'm looking for Windows software that will allow me to quickly create a "checkpoint", do whatever I might need to do to my computer - install programs/drivers/updates, create/delete personal files, reboot the system multiple times, open questionable attachments - and then revert the entire system back to when the checkpoint was created. Essentially I want Windows Restore Points that save my personal files and partitions, too. It sounds like disk imaging might be the ticket, but creating them is much too slow and the restore process too involved... I'm hoping to sacrifice full disaster recovery for speed. Creating a checkpoint should be as close to one-click as possible, and rolling back should be a matter of selecting a restore point and rebooting. Ding! I'm familiar with Sandboxie, True Image Home "Try and Decide", Returnil, and a number of other "virtual system" apps that actively "catch" changes and allow you to commit or reject them. I'm not interested in these for a number of reasons - I prefer the "cut and dry" restore point approach. Finally, I'll note that I've just recently become aware of Comodo Time Machine. It sounds absolutely perfect, however, a quick skim through the user forums show more than a few horror stories of corrupted, unbootable systems. Any positive personal experience with the software to suppress my superstitions, or suggestions for more established alternatives would be greatly appreciated - Comodo Time Machine seems relatively new. Thanks for your help!

  Read the article

• Glassfish v3 failure when startup. "Cannot allocate memory "

  - by Shisoft

  It is clear in this Question Fail to start Glassfish 3.1: java.io.IOException: error=12, Cannot allocate memory But in my case,I have a 512M memory Ubuntu 10.04 vps.It seems that I don't need to change any configure.But when start the server,I got this exception VM failed to start: java.io.IOException: Cannot run program "/usr/lib/jvm/java-6-sun-1.6.0.22/bin/java" (in directory "/home/glassfish/glassfish/domains/domain1/config"): java.io.IOException: error=12, Cannot allocate memory So,I set <jvm-options>-Xmx512</jvm-options> to <jvm-options>-Xmx400</jvm-options> The exception remains.What did I do something wrong? result of free -m total used free shared buffers cached Mem: 512 43 468 0 0 0 -/+ buffers/cache: 43 468 Swap: 0 0 0 result of cat /proc/user_beancounters Version: 2.5 uid resource held maxheld barrier limit failcnt 146049: kmemsize 2670652 5385253 51200000 51200000 0 lockedpages 0 8 2048 2048 0 privvmpages 11134 134522 131200 262200 4 shmpages 648 1352 128000 128000 0 dummy 0 0 0 0 0 numproc 12 73 500 500 0 physpages 6519 28162 0 200000000 0 vmguarpages 0 0 512000 512000 0 oomguarpages 6527 28169 512000 512000 0 numtcpsock 4 14 4096 4096 0 numflock 0 5 2048 2048 0 numpty 1 2 32 32 0 numsiginfo 0 3 1024 1024 0 tcpsndbuf 159600 265744 20480000 20480000 0 tcprcvbuf 65536 3590352 20480000 20480000 0 othersockbuf 44232 90640 20480000 20480000 0 dgramrcvbuf 0 12848 10240000 10240000 0 numothersock 22 31 2048 2048 0 dcachesize 0 0 10240000 10240000 0 numfile 1002 1474 50000 50000 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 numiptent 24 24 2048 2048 0 Thanks

  Read the article

• Ubuntu network card problem.

  - by Steve Greene

  Hello folks, Several days ago, I installed Ubuntu 9.10 onto my Acer Aspire 3100 laptop, running it alongside Widows Vista as a dual-bootable system. Creation of the Ubuntu boot CD went fine, and the installation onto my hard drive was flawless. Ubuntu opens and behaves as I would expect, except for one little problem. For reasons unknown to me, Ubuntu is not communicating with my laptop's networking hardware, and I have no internet connectivity, it works fine under Windows Vista. Up in the right side of the Ubuntu desktop, I click on the network icon and it does not show a wireless connection at all. At home, where I use a dialup modem, I also see no means of getting online. My modem is an HDAUDIO Soft Data Fax Modem with Smart CP,manufactured by CXT (Conexant Systems Inc., file version 4.0.13.0, and the driver version is 7.58.0.0). I am an advanced computer user, but I am not a programmer. I seek a solution that is user-friendly for normal people, something equivalent to a driver that I can easily install or activate that will allow Ubuntu to see my hardware and get me connected. Can anyone help me over this hopefully-little glitch My processor is a Mobile AMD Sempron Processor 3500+ at 1.80 GHz, 1.50 GB RAM, and a 32-bit Operating System.

  Read the article

• Directories shown as files, when sharing a mounted cifs drive

  - by Johan Sigfred Abildskov

  I have an issue where a directory is shown as a file when accessing a samba share ( on Ubuntu 12.10 ) from a Windows machine. The output from ls -ll in the folder on the linuxbox is as follows: chubby@chubby:/media/blackhole/_Arkiv$ ls -ll total 0 drwxrwxrwx 0 jv users 0 Jun 18 2012 _20 drwxrwxrwx 0 jv users 0 Apr 17 2012 _2006 drwxrwxrwx 0 jv users 0 Apr 17 2012 _2007 drwxrwxrwx 0 jv users 0 May 12 2011 _2008 drwxrwxrwx 0 jv users 0 Feb 19 09:53 _2009 drwxrwxrwx 0 jv users 0 Dec 20 2011 _2010 drwxrwxrwx 0 jv users 0 May 8 2012 _2011 drwxrwxrwx 0 jv users 0 Mar 5 11:37 _2012 drwxrwxrwx 0 jv users 0 Feb 28 10:09 _2013 drwxrwxrwx 0 jv users 0 Feb 28 11:18 _Mailarkiv drwxrwxrwx 0 jv users 0 Jan 3 2011 _Praktikanter The entry in /etc/fstab is: # Mounting blackhole //192.168.0.50/kunder/ /media/blackhole cifs uid=jv,gid=users,credentials=/home/chubby/.smbcredentials,iocharset=utf8,file_mode=0777,dir_mode=0777 0 0 When I access the share directly from the NAS on my Windows box, there are no issues. The version of Samba is 3.6.6, but I couldn't find anything in the changelogs that seem relevant. I've tried mounting it in different locations with different permissions, users and groups but I have not made any progress Due to my low reputation on serverfault ( mostly stackoverflow user ) I'm unable to post a screenshot that shows that the directories are shown as files. If I type the full path in explorer, the directory listing works excellently, except for any subdirectories that are then shown as files. Any attack vector for this issue would be greatly appreciated. Please let me know if I have provided insufficient details. Edit: The same share when accessed from a OS X, works perfectly listing the directories as directories. Best Regards!

  Read the article

• How do you recreate the System Recovery environment in Windows 7?

  - by Howiecamp

  I'm running Windows 7 Home Premium RTM (64-bit) and I want to take advantage of the system recovery tools (eg the Command Prompt) without using the Windows 7 DVD. My understanding is that this environment (WinRE) should be installed to your HDD by default as part of the Windows 7 installation. However, when I hit F8 on boot and select "Repair", I get: Windows failed to start. A recent hardware or software change might be the cause. To fix the problem... Status: 0xc000000e Info: The boot selection failed because a required device is inaccessible. The "Info" line seems like the smoking gun. My next step was to boot from the Windows 7 DVD, and choose "Repair". It indicated my Recovery Environment wasn't on the Windows 7 boot menu (perfect) and offered to fix it. I said yes and rebooted, however same issue as above. In addition, when I booted in to Windows 7 and I looked at the boot menu options, the recovery/repair option was not there. Only my Windows installation. Finally, I ran the Disk Management tool (diskmgmt.msc) and took a look at the contents of my "System Reserved" partition (which was set to "Active" as normal). It's unclear to me what the contents should look like, however it is my understanding that the WinRE environment gets installed to this partition. (As part of the above troubleshooting I followed http://superuser.com/questions/25728/how-to-fix-windows-7-boot-process which lead to http://www.sevenforums.com/tutorials/668-system-recovery-options.html).

  Read the article

• Exchange 2007 with Android activesync

  - by lbanz

  A few of our users noticed that it will stop working intermittently for them. I didn't believe it at first until I changed my android phone and it started occuring for me. It will just stop syncing completely, it looks like the server is blocking the device completely. This mainly occurs when they are using the wifi. I've done some testing. If I switch off the wifi and use the phone data plan it will work fine. When it's on the wifi network, I try and browse to the webmail/owa page and it says page not found! I did a dns lookup and they resolve correctly. If I use another device on the same wifi network, it can access the exchange servers fine. Sometimes the wifi network will just work without any issues. But when it fails, it looks like the phone constantly checks the server every second to see if it is online even though I've got it on manual sync. I was wondering whether it tries to sync too many times and exchange thinks its a denial service attack. My old android phone that works is Froyo and the new one is Icecream. People who have reported issues seems to be newer phones. They also tested their own wifi network at home and experience the same problem. We haven't patch our exchange recently before seeing this problem. Anyone has seen this issue?

  Read the article

• How can I setup OpenVPN with IPv4 and IPv6 using a tap device?

  - by Lekensteyn

  I've managed to setup OpenVPN for full IPv4 connectivity using tap0. Now I want to do the same for IPv6. Addresses and network setup (note that my real prefix is replaced by 2001:db8): 2001:db8::100:0:0/96 my assigned IPv6 range 2001:db8::100:abc:0/112 OpenVPN IPv6 range 2001:db8::100:abc:1 tap0 (on server) (set as gateway on client) 2001:db8::100:abc:2 tap0 (on client) 2001:db8::1:2:3:4 gateway for server Home laptop (tap0: 2001:db8::100:abc:2/112 gateway 2001:db8::100:abc:1/112) | | | (running Kubuntu 10.10; OpenVPN 2.1.0-3ubuntu1) | wifi | | router | | OpenVPN INTERNET | eth0 | /tap0 VPS (eth0:2001:db8::1:2:3:4/64 gateway 2001:db8::1) (tap0: 2001:db8::100:abc:1/112) (running Debian 6; OpenVPN 2.1.3-2) The server has both native IPv4 and IPv6 connectivity, the client has only IPv4. I can ping6 to and from my server over OpenVPN, but not to other machines (for example, ipv6.google.com). net.ipv6.conf.all.forwarding is set to 1, I've tried disabling net.ipv6.conf.all.accept_ra as well, without luck. Using tcpdump on both the server and client, I can see that packets are actually transferred over tap0 to eth0. The router (2001:db8::1) send a neighbor solicitation for the client (2001:db8::100:abc:2) to eth0 after it receives the ICMP6 echo-request. The server does not respond to that solicitation, which causes the ICMP6 echo-request not be routed to the destination. How can I make this IPv6 connection work?

  Read the article

• Wireless very slow on one laptop on network, all other machines normal?

  - by th3dude19

  My new laptop (Acer Aspire Timeine 3810TZ running Windows 7 Home Premium 64bit) is acting very strange on my wireless network. Below are the issues I'm noticing... The connection frequently drops. I see the icon change from 'full bars' to 'empty bars with yellow star (meaning no connection)' occasionally. Almost every website I visit (Firefox) hangs for a long time on 'Looking up www.amazon.com' for example. After a long pause, it finally starts loading the website. Neither of these problems exist on any other machines on my network. I also have a desktop running the same OS wirelessly and it works fine. I've run several Speedtest.net tests and the speeds are great (20MBit down/4 up). Results from pingtest.net are as follows: Line quality: D Ping: 46ms Jitter: 65ms Packet Loss: 9% These results are to a server that is less than 10 miles from my residence. The results on the other machines in my house are normal. Any suggestions? This is becoming very annoying as I purchased this machine primarily for browsing.

  Read the article

• Windows XP Disappearing Folders

  - by XenoFoxx

  I am researching a problem for a friend, and unfortunatly do not have direct access to his computer. I've tried to gather as much information as possible and I have researched it on various websites. I've not found anyone having the same problem my friend is having. So here goes: He has a media server in his home running Microsoft Windows XP. It has 3 drives, 1 for the OS and 2 for mass storage. Not long ago he went to access one of the mass storage media drives and it was empty, except for a single folder. His first assumption was that his roommate had deleted everything on the drive (excluding the remaining folder). He then checked the properties of the drive and it was still saying that the hard drive was nearly full. I told him to check the recycling bin, thinking that whoever deleted them didn't clear them from recycling and that they were still taking up space on the drive. My friend said the recycling bin was empty. So we have a drive that the windows file management system says is empty (again except for the remaining folder), but the properties of the drive say it's mostly full. Now it gets weirder My friend tried to create a new folder on this drive and it auto-named itself "New Folder(1)" which means that it recognizes there is already a "New Folder" in that directory. He tried to rename it to a name that he KNEW was there previsouly, and windows wouldn't allow it because it was a duplicate folder name. SO now it seems the folders are there, but not displaying in Windows Explorer. Both of us have no idea why this is occuring, why the folders vanished, why the one remaining folder didn't vanish, or how to make them visable again. Anyone else ever experience this? I can get more details if needed.

  Read the article

• ext3: maximum recommended partition size / handling large partitions

  - by Hansi

  Hi! I would like to do an encrypted install of Ubuntu on a 2 Terabyte drive (i.e., using LUKS/DMcrypt). In order to not have to type in passwords too often, the partitioning scheme will be 50 GB for / and about 1 TB for /home (and the rest for Windows 7), just for clarity. Even though by now LVM is regarded as being stable, I don't want to bother having more room for errors by introducing unnecessary layers of complexity. For both Ubuntu partitions I want encrypted ext3 with the default blocksize of ext3 (4k?). Thoughts: When I look at most partition schemes here on this site or elsewhere, I usually see at most about 400 or 500 GB partitions (maybe I didn't see enough). There may be different reasons for this, but is reliability an issue here? Are larger ext3 partitions, like about 1 TB, harder to handle for the OS or filesystem driver or at some other level? If I make the partition too large, will it be harder to repair in case of corruptions? Are there some default settings for ext3 that I should change for 1 TB partitions? Question: What maximum partition size for ext3 do you recommend and why? Thanks!

  Read the article

• KVM virtual machine unable to access internet

  - by peachykeen

  I have KVM set up to run a virtual machine (Windows Home Server 2011 acting as a build agent) on a dedicated server (CentOS 6.3). Recently, I ran updates on the host, and the virtual machine is now unable to connect to the internet. The virtual network is running through NAT, the host has an interface (eth0:0) set up with a static IP (virt-manager shows the network and its IP correctly), and all connections to that IP should be sent to the guest. The host and guest can ping one another, but the guest cannot ping anything above the host, nor can I ping the guest from anywhere else (I can ping the host). Results from the guest to another server under my control and from an external system to the guest both return "Destination port unreachable". Running tcpdump on the host and destination shows the host replying to the ping, but the destination never sees it (it doesn't even look like the host is bothering to send it on at all, which leads me to suspect iptables). The ping output matches that, listing replies from 192.168.100.1. The guest can resolve DNS, however, which I find rather odd. The guest's network settings (connection TCP/IPv4 properties) are set up with a static local IP (192.168.100.128), mask of 255.255.255.0, and gateway and DNS at 192.168.100.1. When originally setting up the vm/net, I had set up some iptables rules to enable bridging, but after my hosting company complained about the bridge, I set up a new virtual net using NAT and believe I removed all the rules. The VM's network was working perfectly fine for the last few months, until yesterday. I haven't heard anything from the hosting company, didn't change anything on the guest, so as far as I know, nothing else has changed (unfortunately the list of packages updated has since fallen off scrollback and I didn't note it down).

  Read the article

• PHP application failed to connect after a network plugged back in

  - by tntu

  My data-center appears to have had some issues with their network and thus my server has suffered from on an off network connectivity for about an hour. After the connection has been completely re-established my code still kept reporting the same issue over and over until I have restarted the service. The code is a simple PHP code that loops forever checking the Apple feed-back server and then sleeps for a few minutes and then it begins all over again. Now I understand the error being generated if the network is down but once it got back up why did it continue until I have restarted the code? Does PHP have something that needs to be re-initialized or something?? Messges log: Dec 20 08:57:22 server kernel: r8169: eth0: link down Dec 20 08:57:28 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:29 server kernel: r8169: eth0: link down Dec 20 08:57:33 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:33 server kernel: r8169: eth0: link down Dec 20 08:57:37 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:38 server kernel: r8169: eth0: link down Dec 20 08:57:44 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:44 server kernel: r8169: eth0: link down Dec 20 08:57:52 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:52 server kernel: r8169: eth0: link down Dec 20 09:10:58 server kernel: r8169 0000:06:00.0: eth0: link up PHP Error: PHP Warning: stream_socket_client(): php_network_getaddresses: getaddrinfo failed: Name or service not known in /home/push/feedback.php on line 36 Code Line 36: $apns = stream_socket_client('ssl://feedback.sandbox.push.apple.com:2196', $errcode, $errstr, 60, STREAM_CLIENT_CONNECT, $stream_context);

  Read the article

• BSOD error 0x0000006B PROCESS1_INITIALIZATION_FAILED on boot

  - by DontCare4Free

  I reinstalled League of Legends because the patcher always gave me an error. However, out of complete stupidness I didn't uninstall the old installation first because I thought that it would simply replace the files. However, when the installer bar got to 100% it simply minimized. Then I closed the application from the task manager. I tried uninstalling it after a failed attempt to start it up. The same behavior as when I installed it. Then I tried reinstalling where it simply presented the InstallShield Modify/Repair/Remove menu and I selected repair. Nothing happened. Then I tried selecting Modify, then seeing that the only option (called DefaultFeature) was unchecked. Same behaviour as install/uninstall. After seeing that it still failed, I uninstalled again. And after that I deleted C:\Program Files (x86)\League of Legends manually. When I tried installing LoL again it still thought I had it, so I chose repair. This time something actually happened, but it installed the whole game to C:\Windows. Seeing what was going on I clicked cancel and then started it up to try uninstalling it. However, I got an error message about something not being registered and then the minimization to I decided to let it repair completely. Then I uninstalled it and it gave only the minimization. However, when I rebooted another application started up complaining about some library being absent. So I decided to do a system restore. After letting it complete I got a BSOD every time I tried starting up Windows normally or in safe mode. However, system recovery mode works, although the system recovery automatic repair does not fix it. After a bit of searching I found a Microsoft KB article about it (981833) and tried following the workaround instructions. Nothing happened. I am using Windows 7 Home Premium 64-bit and Ubuntu 10.04 LTS 64-bit installed with WUBI.

  Read the article

• How to setup a virtual machine in Ubuntu desktop to run Debian Server

  - by stickman

  I want to run a virtual machine in my Ubuntu desktop that runs a Debian server. The purpose of this is to generate Debian packages. I have some C++ applications that were originally developed on my Ubuntu machine, and I need to (re)compile them on a Debian server in order to: build Deb packages for deployment on a Debian server make sure that the applications will definitely work on a debian server The idea is so that I can do 90% of my development on Ubuntu (where I am more comfortable), and deploy a binary package that definitely works on Debian. BTW, I am developing on Karmic Kola (Ubuntu 9.10). [Edit] Following the advice I got so far, I have installed debootstrap and Debian 'Lenny' on /srv/chroot/debian_lenny on my machine. I am not sure this is the server version, but in any case I dont think that matters for my purposes (though it would be useful to know how to specifically install the server version). At the moment though, I am like a fish out of water, since there is no GUI, and it is only a console that I have in the chroot jail. I had a look in the home folder (I cheated, by using the KNavigator in Ubuntu), and there are no folders there - which presumably mean that no users have been set up as yet in the Debian "system". I would like to know how to do the following: Download and install the dev tools needed for (re)compiling my C++ apps Copy my projects from the Ubuntu "system" to the Debian "system" After building the binaries, I would like to create a debian binary package containing all of my binaries, so that I can install the package on a Debian server (my remote server)

  Read the article

• VirtualBox doesn't see raw partitions

  - by smbear

  What I want to achieve is to set up virtual machine with VirtualBox. Host OS is Windows 7 Home Premium, guest will be (k)Ubuntu 12.04 on a raw partition. The first problem is that when I issue following command: VBoxManage.exe internalcommands listpartitions -rawdisk \\.\PhysicalDrive0 I get following result: Number Type StartCHS EndCHS Size (MiB) Start (Sect) 1 0xee 0 /0 /1 1023/254/63 715404 1 I'm guessing that VirtualBox is unable to see my partitions. If I use diskpart tool, then all partitions are listed correctly (note Polish language version of Windows): DISKPART> select disk 0 Obecnie wybranym dyskiem jest dysk 0. DISKPART> list partition Partycja ### Typ Rozmiar Przesuniecie ------------- ---------------- ------- ------------ Partycja 1 System 200 MB 1024 KB Partycja 2 Zarezerwowany 128 MB 201 MB Partycja 3 Podstawowy 139 GB 329 MB Partycja 5 Nieznany 4883 KB 140 GB Partycja 6 Podstawowy 50 GB 140 GB Partycja 7 Podstawowy 484 GB 190 GB Partycja 4 Odzyskiwanie 24 GB 674 GB Additional note: my PC is using EFI to boot OS. Basing on the results listed above, I believe that: I messed up with my partition table. Something is wrong with VirtualBox. Can anyone help with this issue?

  Read the article

• Win 7 Media Center - TV - No audio on HD channels

  - by Chuzein Part II

  I wonder if you can help. I have recently purchased a PCTV Nanostick DVD-T2 290e I am running Windows 7 Home Premium 64bit and I use Windows media center for almost everything. I run a media center machine in my lounge through my Sony AV Amp onto my HD TV. I bought the Nanostick to watch ‘Freeview HD’ programmes when watching the TV through the Media Center – I also have a Sony Freeview Plus system that the Mrs uses. I installed the Nanostick with relatively no issues and as described by many user reviews Media Center picked up the new USB tuner and scanned all the new channels and I was presented with all the HD channels. The issue I have is that there is no audio sound from the HD channels but perfect video. SD works fine. The software that comes with the Nanostick works fine – both sound and vision are perfect for the HD channels. As mentioned, I run my Media Centre lots. I have an extensive DVD and BD collection stored on a server and DVD and BD all play perfectly through Arcsoft Total Media Theatre 5 – with no issues on either SD or HD. My sound card is built into my motherboard and that sends the audio signal to my gfx card and that in turn passes it through to my Sony AV Amp that decodes the audio to be heard on my 5.1 set up. Does anyone have any ideas. I have searched lots on the net and I cant find anyone else with the same issue. I am aware of codecs etc but I don’t really understand it. It also puzzles me that when I read the user/buyer reviews for this product so many people tell the story of faultless installations on the same kind of set up as me.

  Read the article

• Windows 7 Paging file apparently not being used

  - by Daniel F.

  I'm running Windows 7 Home Premium 32bit on a mobo with 24GB RAM. Of those 24GB, 20GB are assigned as a RAMDISK via ASRock XFastRAM. This RAMDISK has the drive letter X assigned to it. On X:\ I'm storing the temporary files folder, as well as pagefile.sys. Pagefile.sys has 6GB of size. The X:\ has usually around 14GB free space, so the temporary files are negligible, it's mostly the browsers which are storing their caches on there. Now my issue is that Firefox is crashing a lot on me, no error message pops up, but I know that this is because it's out of memory. I could kind of live with that, but now that I switched from using Eclipse to Android Studio, I know that I'm in trouble, because Java isn't capable of allocating, and Android Studio, together with the Java instances it launches, is quite a memory hog. So I tried to figure out what's wrong, and apparently Windows isn't swapping out memory onto the paging file. While my applications are crashing (firefox) / not starting (java vm's), the paging file is only using constantly around 15% of its size (checked with the performance monitor). 15% equals to 1GB aprox. I know that the correct solution would be to switch to 64 bit Windows, but I had to use the 32 bit version because of driver issues which I had about two years ago, and I guess that I'll have them again if I reformat and install the 64 bit version. Also, the machine is running quite stable, the only issue is the memory, so I'd like to use it as it is (as the apps are installed and configured) Is there a way to make Windows use the paging file more efficiently? None of my processes require more than 1GB, I'd just like it to swap out some seldomly used stuff, like GoogleCrashHandler.exe and stuff like that in order to have "more physical memory avaliable". Is that possible?

  Read the article

< Previous Page | 466 467 468 469 470 471 472 473 474 475 476 477  | Next Page >