Search Results

Search found 13995 results on 560 pages for 'home'.

Page 472/560 | < Previous Page | 468 469 470 471 472 473 474 475 476 477 478 479  | Next Page >

• Permission denied (publickey,gssapi-with-mic,password) ssh error

  - by zentenk

  Heads up I'm a noob with linux and networking. I set up a ubuntu server and I have a static ip for my network. When I try to connect to the server at home (external), it prompts me to log in. I supply the correct password (or incorrect pw), I get the error Permission denied, please try again. and after 3 times I get Permission denied (publickey,gssapi-with-mic,password) I am however able to connect with SSH from another computer in the same network with ssh < internal ip of server > I'm connecting with mac os x and my config file is vanilla. Note: During installation of ubuntu it says I don't have a default route or something while doing auto network configuration, but I ignored it and continued the installation, could this be the problem? EDIT: I have tried the below, I have nothing in hosts.allow and also iptables shows the ports that I have allowed, which is 22. I checked the auth.log, and there is nothing when I connect to it remotely (even when it says permission denied). I have tried connecting to it internally and the correct authentication logs show. Any idea whats wrong?

  Read the article

• Is there a standard method for assigning nameservers to servers in a Windows domain?

  - by HopelessN00b

  As the title asks, I'm wondering if there's any standard or "best practice" for how to actually assign nameservers (DNS) and manage the nameserver configuration for client servers on a Windows domain. I'm talking about the setting circled in the below image, in case the language of the question is not clear enough: This is for a large, multi-site environment, where ideally/hopefully all servers point at their site's Domain Controller as the primary DNS server, and a DNS server at a different site as the secondary DNS server. For simplicity's sake, we can say that the secondary server would be the Domain Controller at the home site for everyone, and there are no tertiary DNS servers (even though that's not actually the case). Try as I might, I can't seem to find a GPO setting for this (at least on FL 2003 R2, the Computer Configuration - Administrative Templates - Network - DNS Client - DNS Servers GPO is Supported on: Windows XP Professional only), and I find it rather hard to believe that the "best"/"standard" solution would therefore be either scripting up something to apply the DNS settings per site, or using a DHCP server to push those configurations out to the other servers via the DHCP Scope Options. So, is there a standard way of managing this configuration? (That's hopefully not "a script" or "DHCP Scope Option.)

  Read the article

• Why doesn't NFS recognize a new UID?

  - by user76177

  I have two servers running RHEL6. I have root access to both. The main server, which I will refer to as server, is a database server. The application server, which I will refer to as client, mounts a directory from server via NFS. There is a user, appuser, on both client and server. However, appuser's UID on client is 502. appuser's UID on server is 506. Both users need read and write capability on the NFS share. To facilitate this, I made the share owned by appuser on server. Running id appuser on each yields: uid=506(appuser). Of course, client does not recognize that ownership, since appuser has a different id on client. So I did the following: Changed UID of user in /etc/passwd on client to be 506. Changed ownership of appuser's $HOME on client to be appuser again so that I could log in. Now, when I go to look at the NFS share from the client side, I see that it is owned by 502. 502 is the OLD id for appuser on client. I can't change ownership of the NFS share from client, since that is a volume that physically resides on server. I need to make sure that the NFS share shows ownership of appuser from both server and client. What step have I missed since changing the appuser id on client? NOTE: I have not rebooted client (or anything else.)

  Read the article

• Ubuntu server apt-get says "(-5 - No address associated with hostname)"

  - by Srini

  I have a ubuntu 12.04 server. Running sudo apt-get update on it produces errors like this: W: Failed to fetch http://au.archive.ubuntu.com/ubuntu/dists/precise-backports/main/binary-i386/Packages Something wicked happened resolving 'au.archive.ubuntu.com:http' (-5 - No address associated with hostname) I am able to ping all the other hosts on the network and also Google's DNS 8.8.8.8. But am unable to ping www.google.com. So, I'm guessing something is wrong with my DNS setup, but not sure what. I use static IP and my /etc/network/interfaces looks like this: auto eth0 iface eth0 inet static address 192.168.1.50 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.0.255 gateway 192.168.1.1 #dns-nameserver 203.12.160.35 203.12.160.36 #nameserver 203.12.160.35 203.12.160.36 My /etc/resolv.conf and /etc/resolvconf/resolv.conf.d/base are both empty and my /etc/resolvconf/resolv.conf.d/original says: nameserver 192.168.1.1 Any help would be greatly appreciated. P.S. I've googled it a bit and the common resolution is to switch to DHCP which I don't want to do since this is my home server. Thanks Srini

  Read the article

• Why did you start with Linux ? And why did you continue using it ?

  - by Stefano Borini

  I'd like to know the reasons that moved you towards Linux. Personally, I started because we had to use a Digital for the Fortran 77 exercises during my first year at the university. Linux was installed on many university computers, and I got interested in it. I always liked to code (on the C64) in basic and assembler, but I knew nothing about other languages. I soon discovered a chat engine called NUTS, and the idea of becoming proficient in C appealed me, so I started hacking the code. To do so, I needed a Unix at home, so I bought a Slackware 3.4 and installed it on my Pentium 166. I then continued using it for many years, reason being that I had pleasure in learning new things and the openness of information about the internals. It was a great learning platform. I then moved to osx because I enjoy the power of Unix with the beauty and efficiency of its interface. I am interested in your answer because I believe that the panorama has changed somehow. Although I still guess to find many "hackers" interested in Linux for the sake of knowledge, I also believe that there are other reasons (work, friends, bought a netbook).

  Read the article

• Ubuntu 8.04 wont reboot from script

  - by Littlejon

  I have a script that is run to backup a server via Rsync, after that script is run I want the server to reboot. My script is run as root from the Crontab at 3am in the morning. #!/bin/bash HOST="email" RSYNC_OPTS="-a -v -v --progress --stats --delete" RSYNC_DEST="10.0.0.10::$HOST" BACKUP_LIST="/etc /home /root" TIMESTAMP="/timestamp-bkup-start.chk" TIMESTAMP2="/timestamp-bkup-stop.chk" touch $TIMESTAMP rsync $RSYNC_OPTS $TIMESTAMP $RSYNC_DEST for BACKUP_ITEM in $BACKUP_LIST; do rsync $RSYNC_OPTS $BACKUP_ITEM $RSYNC_DEST done /etc/init.d/zimbra stop sleep 60s rsync $RSYNC_OPTS /opt $RSYNC_DEST touch $TIMESTAMP2 rsync $RSYNC_OPTS $TIMESTAMP2 $RSYNC_DEST echo `date +%Y%m%d%H%M` >> /var/log/reset reboot # $# shows number of args passed # $1 to access first variable #if [ $# -eq 1 ]; then # if [ $1 = "withreboot" ]; then # echo "rebooting..."; # echo `date +%Y%m%d%H%M` >> /var/log/reset # /sbin/reboot # fi #fi I have tried using init 6 rather then reboot. I have tried /sbin/reboot. I also have another basic script that just echos to the reset log and runs reboot without issue. It is just with the script above the server wont restart. If anyone has any theories that would be great as I have run out of idea. Thanks, Jon

  Read the article

• Configuring two nearby WLANs: should I use the same ssid?

  - by Rory

  I'm configuring a home network for basic internet use (ie don't really need connectivity between workstations on the network). My brick walls mean a single wireless router doesn't provide good coverage throughout the house, so I have purchased two powerline adapters and now have the incoming modem/wireless router at one end of the house plugged into a powerline adapter, and at the other end of the house the other powerline adapter plugged into another wireless router. Currently the two wireless networks have different ssids. (The powerline adapters only do power-Ethernet; they're not wireless access points themselves.) This works well, except when I move between rooms and would ideally like my devices (iPad, phones, laptops) to switch from the weak to the strong signal. Sometimes there's enough signal that they hold on to the weak connects instead of switching to the strong one. Should I name the two networks the same ssid, and if so what is the actual effect? Do the signals get confused, is the bandwidth affected, will this help my devices seamlessly move from one to the other, or is the ssid just a cosmetic thing that actually doesn't have any impact on this situation? Are there any other settings that I should configure to make my setup optimal?

  Read the article

• can't get to admin page after factory reset netgear wg602

  - by stefanB

  I have wireless Netgear wg602 on my home network (connected to my internet modem/router). I've had it secured and locked down to only accept connection from specific MAC addresses. I've forgotten the password that I used but my Mac Book laptops can still connect (multiple OS updates - it can't retrieve and display the password but it can use it to log in to WPA) so I want to reconfigure it from scratch (have some new devices). I tried to reset the Netgear wg602 to factory settings (pressed reset button for 10 sec), reset my laptop IP address to local address suggested in manual (192.168.0.210 net mask 255.255.255.0), connect Netgear via ethernet cable to my mac book pro but I can't get to the admin page at 192.168.0.227 as suggested by manual (firefox or safari). At this stage the Netgear is not connected to router, it is only connected to mac book. I can't ping the wireless access point either (but it is on all lights are on). What am I doing incorrectly? Last time I configured it via Windows now I only have Mac Book (which I've used with the wireless access point for 2 years so no compatibility problems).

  Read the article

• Where did my backup files go? Can they be recovered?

  - by Ken

  I just purchased a Western Digital Essential SE 1TB external hard drive from Best Buy at their recommendation. I then exchanged it for a Toshiba Canvio (I think that was the name). I have a Toshiba Qosmio X505-Q898. The Canvio locked up my computer and rewrote some kind of OS file, and erased all the restore points as well as the system image backup (according to Best Buy) just by plugging it in for the first time. Never even got to the install part or anything -- plugged it in and fried my computer. They spent about an hour and a half on my computer and got it back to a somewhat working condition and gave me access to my files. So now they say I have to back it up using my recovery disk and rewriting my OS. Enter the Essential. Brought it home last night, plugged it in and installed everything. Works perfect, no problems. Backed up everything on it. I unplugged and plugged it twice to make sure that everything was on it. Essential told me it had both the HDD and SSD backed up. So I reinstalled my OS. Plugged the Essential in and everything loads right up. Went to retrieve my files and the Western Digital has nothing on it. It shows all my music, pics, ETC. as still being on my computer and needing to be backed up, but since there are no files on my computer now. Where is this information coming from and where did my files go? It's about 810GB worth of files I've amassed over several years. Is there any way to recover data from this? I plan to contact Western Digital and Best Buy, just thought I would check here too. Any advice will be appreciated as a lot of these files are invaluable to me.

  Read the article

• Why does GIMP start up so slow on my machine?

  - by muntoo

  EDIT 2: One way would be to disable script-fu. Does anyone know how to disable it at startup? Is it possible? Would GIMP still work? What wouldn't work? Could I start it later, after loading? Is there any way to speed up GIMP's startup time on Windows Vista Home Premium 32-Bit 1.6 [Dual] Intel Processors? On XP [different computer], it loads in less than 3 seconds. On Vista, it takes 20 seconds: 2 Seconds (other - fonts, brushes, etc) 18 Seconds (extension-script-fu) It just freezes at extension-script-fu. Looking at Process Explorer, I see that it's not taking any CPU at all. EDIT 1: It does seem to be taking 50% of the CPU. It gets stuck for about 18 seconds, and then starts working again. Then, the actual GIMP program pops up [...finally]. I have the latest stable version running (I think). I tried it with XP SP2 Compatibiliy mode and/or Run As Administrator, but that didn't help.

  Read the article

• Encrypted Windows 7 & Linux Advice Wanted

  - by Miles

  I would like to set up my laptop to dual boot Arch Linux and Windows 7 with file sharing and encryption. Just wanted some advice on going about this because I have not dealt with encryption nor file sharing. I have two 500GB hard drives, and this is my plan: Install Windows 7 across both hard drives Use a live CD to wipe out Windows boot loader and replace with Grub Legacy Use live CD to wipe out second hard drive and re-size the Windows partition located on first hard drive Install Arch Linux along side with Windows 7 on first hard drive, all remaining space goes to home folder as ext2 Install truecrypt and ext2fsd Concerns: Is this the most efficient way to share files between both OSes? Or should I just be using NTFS to store all my data? How would the file permissions work when sharing files between Windows and Linux? Is there a high likley hood of corruption, and what is the ease of backing up files from an encrypted disk? Anything I should look out for, conflict between Grub and Truecrypt? Thank you for any advice, and feel free to post any links you might find useful to me. I am trying to plan this out so I can minimize downtime as I do not want to spend more than a night on this, nor do I want to run into a major problem some time in the future.

  Read the article

• Apache2 403 permission denied on Ubuntu 12.04

  - by skeniver

  I have a sub-directory in my /var/www folder called prod, which is password protected. It was all working fine until I asked my server admin to help me set up allow all access to one particular file. Now the entire folder is just giving me a 403 error. This is the sites-enabled file: <VirtualHost *:80> ServerAdmin [email protected] # Server name ServerName prod.xxx.co.uk DocumentRoot /var/www/prod <Directory /var/www/prod> Options Indexes FollowSymLinks MultiViews +ExecCGI Includes AllowOverride None Order allow,deny AuthType Basic AuthName "Please log in" AuthUserFile /home/ubuntu/.htpasswd Require valid-user </Directory> <Directory /var/www/prod/xxx/cgi-bin/api.pl> Allow from All Satisfy Any </Directory> ScriptAlias /xxx/cgi-bin/ /var/www/prod/xxx/cgi-bin/ ErrorLog ${APACHE_LOG_DIR}/prod.xxx.error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/prod.xxx.access.log combined </VirtualHost> Now he's unsure why this is blocking me out completely. No permissions have been changed, but this is the /var/www/ folder: 4 drwxr-xr-x 2 root root 4096 Jan 3 21:10 images 4 drwxr-sr-x 4 root www-data 4096 Mar 31 14:47 jslib 4 drwxr-xr-x 7 root root 4096 Jun 2 13:00 prod When I try to visit http://prod.xxx.co.uk, I don't get asked for the password; I just get 403'd I hope I've given enough information... Anyone able to spot something he can't?

  Read the article

• SSD as primary or secondary drive on a small Linux server?

  - by Alex Martelli

  I'm pensioning off my 10-years-old home server and replacing it with an Ubuntu 10.04 box. The two storage devices are a Western Digital Caviar Green 2.0TB HD and an Intel X25-M 34nm Gen 2 80GB SATA II 2.5inch SSD (the box has 8GB RAM and an i5 750, if it matters). I don't care much about boot times (since I don't plan to reboot all that often;-); the main frequent, performance-demanding task will be (re)building large open source C or C++ software packages from sources (as an open source contributor, I do that often). So, I thought I'd keep the SSD as the secondary drive and the HD as the primary one, using the SSD mostly for the files that can otherwise demand a lot of seeking (esp. in a parallel make). However, the friendly vendor (perhaps more experienced in Windows systems than in Linux ones) thinks the "normal" way to configure the machine would be with the SSD as the primary drive. I'm pretty rusty on configuring and tuning systems, so, I thought I'd better double check on SuperUser... thanks in advance for advice about this choice!

  Read the article

• Wireless Access Point stopped working

  - by Alex Pritchard

  I have a simple LAN set up at home using a Linksys WRT54GSV4 as my primary router and an Encore ENHWI-2AN3 as an access point. I connect the Encore to the Linksys by running a cable from one of the Linksys LAN ports into the Encore WAN input. I originally configured this using the Encore setup wizard, setting the device up in AP Router Mode. It detected the input network and worked about as expected, creating a second network that used my primary network to connect to the internet. It worked fine for about 2 weeks, then abruptly cut out today. I checked to make sure the network was still live through the cable going into the Encore (provides internet when connected to a laptop directly) and that devices are still able to connect to the network being broadcast by the Encore. When I try to rerun the connection wizard on the Encore, I receive the message "No Services found in WAN port." The WAN Settings is no longer retrieving a dynamic ip from the line. I tried providing a static IP, assigning an IP address within the subnet range of my primary router that wasn't being used and pointing the Default Gateway to the Linksys IP, but this did not work either. When I plug the cable into the WAN port, an internet light comes on that is not lit when a live network is not connected. I've tried doing a hard reset on the Encore (held down the rest button until the lights flashed, reconfigured from scratch), but the WAN settings are still not detected. Also tried powering off and on the modem, linksys, and encore. Any suggestions would be appreciated!

  Read the article

• Strange ssh login

  - by Hikaru

  I am running debian server and i have received a strange email warning about ssh login It says, that user mail logged in using ssh from remote address: Environment info: USER=mail SSH_CLIENT=92.46.127.173 40814 22 MAIL=/var/mail/mail HOME=/var/mail SSH_TTY=/dev/pts/7 LOGNAME=mail TERM=xterm PATH=/usr/local/bin:/usr/bin:/bin:/usr/bin/X11:/usr/games LANG=en_US.UTF-8 SHELL=/bin/sh KRB5CCNAME=FILE:/tmp/krb5cc_8 PWD=/var/mail SSH_CONNECTION=92.46.127.173 40814 my-ip-here 22 I looked in /etc/shadow and find out, that password for is not set mail:*:15316:0:99999:7::: I found this lines for login in auth.log n 3 02:57:09 gw sshd[2090]: pam_winbind(sshd:auth): getting password (0x00000388) Jun 3 02:57:09 gw sshd[2090]: pam_winbind(sshd:auth): pam_get_item returned a password Jun 3 02:57:09 gw sshd[2091]: pam_winbind(sshd:auth): user 'mail' granted access Jun 3 02:57:09 gw sshd[2091]: Accepted password for mail from 92.46.127.173 port 45194 ssh2 Jun 3 02:57:09 gw sshd[2091]: pam_unix(sshd:session): session opened for user mail by (uid=0) Jun 3 02:57:10 gw CRON[2051]: pam_unix(cron:session): session closed for user root and lots of auth failures for this user. There is no lines with COMMAND string for this user. Nothing was found with "rkhunter" and with "ps aux" process inspection, also there is no suspicious connections was found with "netstat" (as I can see) Can anyone tell me how it is possible and what else should be done? Thanks in advance.

  Read the article

• Utility to grant admin rights to a user in Windows XP for few hours/days?

  - by user15660

  I have two accounts on my windows xp home desktop. The default regular user is used for everything and the 2nd user which has admin rights is used only for installations. I do this to avoid malware infestations during web browsing and limited user account is guarding against online threats to a good extend but many programs refuse to run under limited rights like revo uninstaller. many installs i run from limited user by selectin "run as" from right click context menu of the .exe file. but some apps need admin rights for certain. I use "switch user" to go to admin mode and do the install/uninstall. but the admin user has none of my preferences bookmarks setup nor has my locate32 indexing done and ready for fast search Is there a utility which I can use "run as" login in administration login and use that to grant my limited user admin rights for a limited amount of period like few hours or days? Please help. I guess MS might have closed many doors of it for fear of exploitation of the API. are there any?

  Read the article

• How do I change file protections running XP on a disk from Windows Server?

  - by cdkMoose

  I had a Windows Server 2003 machine running at home, along with my desktop which I use for development. Server went belly up, but since my desktop is reasonably powerful, I figured I would move the disk from the file server (it was OK) into my XP machine to keep all of the files. Disk comes up fine and shows all of the files. I have been getting access denied errors when trying to work with some of the files. When I display attributes in Explorer, none of them are marked Read-Only. When I view properties on the directories, the Read-Only checkbox is not checked, but has a green background(which I thought meant mixed usage for files in the directory). When I click on the checkbox to clear it and click Apply, the disk does some work and all looks well. However, I continue to get the Access Denied errors, the files still don't show any Read-Only attribute and the directory properties shows the green background again on the Read-Only checkbox. I did check the box which says to apply the change to the folder and all files /subfilders under it. I am assuming that the issue relates to userids/permissions carried over from the Server install. So, why does it let me think I can change the attribute when I can't and how can I correct this problem so that the disk correctly recognizes the ids from XP?

  Read the article

• Macports install of ack doesn't create correct executable

  - by user1664196

  I am trying to install p5-app-ack port from Mac Ports, but it seems it doesn't create a /opt/local/bin/ack binary at the end: $ sudo port search *app-ack Password: p5-app-ack @1.960.0 (perl) A grep replacement that ignores .svn/CVS/blib directories p5.8-app-ack @1.960.0 (perl) A grep replacement that ignores .svn/CVS/blib directories p5.10-app-ack @1.960.0 (perl) A grep replacement that ignores .svn/CVS/blib directories p5.12-app-ack @1.960.0 (perl) A grep replacement that ignores .svn/CVS/blib directories p5.14-app-ack @1.960.0 (perl) A grep replacement that ignores .svn/CVS/blib directories p5.16-app-ack @1.960.0 (perl) A grep replacement that ignores .svn/CVS/blib directories Found 6 ports. $ perl --version This is perl 5, version 12, subversion 4 (v5.12.4) built for darwin-thread-multi-2level Copyright 1987-2010, Larry Wall Perl may be copied only under the terms of either the Artistic License or the GNU General Public License, which may be found in the Perl 5 source kit. Complete documentation for Perl, including FAQ lists, should be found on this system using "man perl" or "perldoc perl". If you have access to the Internet, point your browser at http://www.perl.org/, the Perl Home Page. $ sudo port install p5-app-ack ---> Computing dependencies for p5-app-ack ---> Cleaning p5-app-ack ---> Updating database of binaries: 100.0% ---> Scanning binaries for linking errors: 35.0% ---> No broken files found. $ $ ls /opt/local/bin/ac* /opt/local/bin/ack-5.12 /opt/local/bin/aclocal /opt/local/bin/aclocal-1.12 /opt/local/bin/activation-client /opt/local/bin/acyclic $ which ack $ ack -bash: ack: command not found Update If I then try to install p5.12-app-ack afterwards, I get $ sudo port install p5.12-app-ack Password: ---> Computing dependencies for p5.12-app-ack ---> Cleaning p5.12-app-ack ---> Scanning binaries for linking errors: 100.0% ---> No broken files found. $

  Read the article

• Pinging computer name in LAN results in public IP?

  - by Bob

  Hi, I recently introduced a new machine to my LAN. The computer name for this machine is 'server'. Historically I've been able to access machines from my home network (from a web browser or RDP) using the machine name and it resolves to a local IP address just fine. However, I can't seem to do this anymore. When I ping the computer name, I get the following: C:\Users\Robert>ping server Pinging server.router [67.215.65.132] with 32 bytes of data: Reply from 67.215.65.132: bytes=32 time=24ms TTL=54 Reply from 67.215.65.132: bytes=32 time=23ms TTL=54 Reply from 67.215.65.132: bytes=32 time=24ms TTL=54 Reply from 67.215.65.132: bytes=32 time=24ms TTL=54 I notice also that it appends the 'router' suffix to my domain name for some reason. 'router' is the name of my router, obviously. I'm also using OpenDNS as my DNS provider (configured through my router so it gets passed down through DHCP). Why is this not working for me? Can someone explain how the DNS resolution should take place? For LAN resolution, it shouldn't go straight to OpenDNS. I thought that each Windows machine kept it's own sort of "mini DNS server" that knows about all machines on the local network and it first tries to resolve using that. Please let me know what I can do to get this working!

  Read the article

• Is it ok to share private key file between multiple computers/services?

  - by Behrang

  So we all know how to use public key/private keys using SSH, etc. But what's the best way to use/reuse them? Should I keep them in a safe place forever? I mean, I needed a pair of keys for accessing GitHub. I created a pair from scratch and used that for some time to access GitHub. Then I formatted my HDD and lost that pair. Big deal, I created a new pair and configured GitHub to use my new pair. Or is it something that I don't want to lose? I also needed a pair of public key/private keys to access our company systems. Our admin asked me for my public key and I generated a new pair and gave it to him. Is it generally better to create a new pair for access to different systems or is it better to have one pair and reuse it to access different systems? Similarly, is it better to create two different pairs and use one to access our companies systems from home and the other one to access the systems from work, or is it better to just have one pair and use it from both places?

  Read the article

• VirtualBox with Ubuntu Server guest can't ping outside

  - by Danidan

  Here's my situation: an Ubuntu 12.04 Host running VirtualBox; two guest VMs running Ubuntu Server 12.04 home network, so my Host pc has a wireless connection to the router of my ISP. My problem is in one of the virtual machines: it has 3 NICs, one in NAT mode and the others in Host Only mode. My purpose is to use eth0 (NAT) for Internet access and eth1, eth2 (Host Only) for management of internal virtual network (eth1 uses a VBoxNet with this IP 192.168.69.254). Whenever I try to $ping 8.8.8.8 I get Destination Host Unreachable. While if I $ping 192.168.69.10, that is the IP of the other VM, it works. I can't also ping my Host nor my router My /etc/network/interfaces file is: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp auto eth1 iface eth1 inet static address 192.168.69.1 netmask 255.255.255.0 auto eth2 iface ifconfig $IFACE 0.0.0.0 up up ip link set $IFACE promisc on down ip link set $IFASE promisc off down ifconfig $IFACE down $route -n returns: Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 10.0.2.2 0.0.0.0 UG 100 0 0 eth0 10.0.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.69.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0 Forgetting for now what eth2 needs to do and its setup, why I can't go outside the Host box? What can I do to help you helping me? :-)

  Read the article

• backup an existing linux server to a virtualbox virtual machine

  - by user146526

  I have some servers and VPSs to many companies across the world. I want to back them up locally. I have some backup solutions enabled to remote hosts, but I want to have a local backup on a computer at home. What I am thinking is: 1) Create a virtualbox virtual machine, install the same version linux as the server. 2) Use rsync to backup the server to the local virtualbox machine. (something like rsync -av --delete --progress --exclude '/dev/' --exclude '/proc/' root@server_ip:// / ) 3) Repeat the command every few days update files. 4) In case of a hard disk failure, or any other bad event, reverse the rsync command and get the files back and continue my bussiness. I tried it with 2 openvz VPS, the one was a backup of the other. I also tried to transfer normal linux server host to openvz machine and it worked great. That way looks pretty clean and easy to me, this is the kind of solution I am looking for. However I need to be sure that this will work if I am going to do it. The question is, will that work ok ? Does anyone see any problem with that ? Do you have any other suggestions ? Thanks

  Read the article

• MacBook Pro with OSX 10.6.3 (Snow Leopard) Wi-Fi network connection breaks after few minutes

  - by Yanick Landry

  I have a MacBook Pro with OSX 10.6.3 (Snow Leopard). After connecting on a Wi-Fi network, the connection "breaks" after a few minutes. What I mean by "breaking" is that all requests, whether it is loading a web page, connecting to a share folder, connecting to my local router at 192.168.0.1, or pinging anything doesn't get through (time out). When in a "break" situation, I can see in the Network Settings panel that I still have an active IP, which I can successfully ping. I have this problem at home with a router D-Link DI-624 and at work with a D-Link WBR-2310, all with updated firmwares. I thought DHCP was the issue. So I tried assigning a fixed IP address (192.168.0.166). It successfully connects, but after a few minutes, the connection still breaks. The solution I'm currently using is that I disable the AirPort (on the Network icon menu in the top bar), wait a few seconds then re-enable it. It then quickly works, but the connection still breaks after a few minutes. I tried Googling my problem but I think I can't find any good keywords ! It's my first question here, so sorry if I don't respect some rules.

  Read the article

• How to migrate Outlook Express mail rules?

  - by ronwest

  I have a home computer that only had a 15Gb C: drive, and ran out of space with all the Microsoft Updates, etc, that keep coming down. So I fitted a 160Gb drive as a C: drive and altered the drive jumpers to make the old C: drive into a slave D: drive, to save migrating documents, etc. I've installed a clean copy of Windows XP SP3 and reassigned the new Outlook Express' mailstore path to point to the old mailstore folder that now has a D: drive letter - and it all works OK. However, my extensive list of mail rules have not been transferred to the new OE and I have not been able to identify how they are stored. To find it I added a new rule to the new OE, exited OE, then searched on the whole computer (including hidden/system files) for files altered around the time I added the rule. I hoped I could just overwrite a new empty file with an old one. But the only files that seem to be changed are Windows system-level files and some bits and pieces in the Windows\PreFetch sub-folder. None of them can be opened as XP has them locked, and none of them have names that are anything to do with email or rules. Does anyone know of any way of migrating OE rules, or do I have to re-enter them by hand? Thanks!

  Read the article

• How can I monitor network traffic?

  - by WIndy Weather

  I have a home network with about 10 devices including BluRay player [netflix] and both windows and linux machines. I need to collect network traffic statistics so that if questions come up about how much traffic I'm using I have the answer independent of my ISP. I've looked at DD-WRT, but I see that even buying a new router that will be supported is a problem since I might get the wrong version of the hardware. I have a DIR-655 and a DIR-501 - neither of which is supported. I don't mind buying new hardware, but it looks like a crap-shoot to get one that will work. DD-WRT looks like a bad solution unless someone knows of a place to get a router that is guaranteed to work. Does someone know of an arduino or other SBC solution? I have plenty of NAT routers already, so I just need traffic statistics for external traffic. The network is GBit Ethernet inside and Cable / soon to be DSL outside. The DIR-655 only gives me "packets", not bytes transferred oddly enough. Thanks, ww

  Read the article

< Previous Page | 468 469 470 471 472 473 474 475 476 477 478 479  | Next Page >