Search Results

Search found 17009 results on 681 pages for 'screen orientation'.

Page 472/681 | < Previous Page | 468 469 470 471 472 473 474 475 476 477 478 479  | Next Page >

• CPU fan turns on and off repeatedly without booting

  - by rnso

  My PC has suddenly stopped starting up. On checking with case open, the CPU fan starts running when the power is turned on, but it stops after about 2-3 seconds, restarts again after about 2-3 seconds and the loop is repeated. There is no beep and nothing appears on the screen. On searching the internet, I found there could be several reasons for this. I tried removing hard-disk, CD drive, tightening connections etc but of no avial. I also tried using a new power supply but the response is the same. Where could be the problem and how can it be solved? Thanks in advance.

  Read the article

• Ubuntu 12.04 using b43-fwcutter

  - by Nathan

  I have used 10.04 with the b43-fwcutter driver to drive my BCM4318 Broadcom card (a Linksys WPC54G v3) on my old Dell Inspiron 8100 for two years+ with no troubles. I just upgraded to 12.04 and although everything worked fine after install, before I added the b43-fwcutter driver, once I installed the driver, the system refuses to boot. Even before I install the Linksys card!! It just hangs on boot with graphical garbage on the screen. I tried several attempts to recover the system using the live CD, and finally reinstalled completely. I have been thru the cycle, install fresh system, verify everything works, then install b43-fwcutter and it is hung, several times. Consistent hard fail. The system runs fine on hardwire Ethernet, and wireless was fine on 10.04. But I cannot get there with 12.04. So after several attempts, I am now ready to admit defeat and ask for help. I have read every thread that search turned up, and either the advice is to do what I did, i.e. install fwcutter, or does not apply (Different Broadcom, STA, legacy, whatever) So what do I need to do to fix it? Or is the B43-fwcutter driver broken for 12.04? Thoughts? Tips? Log files needed??

  Read the article

• external display in Ubuntu 13.04

  - by thuc2009

  I have had a look on series of similar topics but I could not find a right answer. Currently, I bought laptop Dell latitude E6530 and installed Ubuntu 13.04 (64 bit) alongside with Windows 7 (I could not get rid of it because of some special programs for work). Ubuntu worked well, however, it did not detect the external displays (Dell 23" and Dell 19") no matter I plugged them before or after booting. Edited: I connected my laptop to those external displays through a laptop dock. I went to Settings- Display, the displays were there, but when I enabled them, Ubuntu logged off automatically. No external display was detected. In addition, the laptop screen sometimes was detected as Dell 23" I got an advice from similar topic that nvidia driver should be updated to version 313 or 319. I upgraded driver and the unity launcher disappeared, main display resolution turned to 640*480 and none of external displays was detected. I tried to use additional drivers, but when I turned it on, it told me that there was no driver to be used. Could some one tell me what should I do ? Edited : options vmwgfx enable_fbdev=1

  Read the article

• Botting from a stick drive

  - by Zap

  Am trying to boot from a usb stick. Have carefully followed the instructions at the following link and successfully downloaded and installed version Ubuntu 12.04 desk top: http://www.ubuntu.com/download/help/create-a-usb-stick-on-windows I used the Universal-USB-Installer-1.9.0.2 as instructed and choose the "Ubuntu 12.04 desk top" option, after downloading the respective iso/zip file onto my Dell laptop from the Ubuntu site. Also modified my bios to select the usb first as boot drive instead of hard drive. Also, turned off bit blocker on my laptop and usb stick. Usb stick has the setting of "Automatically unlock this drive on this computer". When i reboot my laptop, it first boots into a black screen (i assume is the bios), but prompts saying "Remove disks or other media. Press any key to start". I press any key and regardless the laptop boots up to windows. Hence, it appears that the boot process is checking the USB first before going to the hard drive to look for it's boot disk and starting Windows 7. Is it that the USB stick is not correctly configured with Ubuntu as a boot disk? Is there anything else that i need to do besides the instructions at the following link? http://www.ubuntu.com/download/help/create-a-usb-stick-on-windows How can I ensure that USB boot stick is configured correctly? After running the Universal-USB-Installer-1.9.0.2 to "install" Ubuntu, is there additional configuration/installation steps? What is the first file that the bios would look for on this USB drive? Is this configured somewhere in the bios, or would it just look for an grub file or /boot dir? The only message i get when booting is "Remove disks or other media. Press any key to start". Any and all help would be much appreciated.. Thanks ... :)

  Read the article

• Problem installing Windows Server 2008 R2 on Xen 3.0

  - by GodEater

  Hi there folks, I've been googling this for a few hours now and not really getting anywhere. We have a Xen 3.0 host which I'm trying to install a copy of Windows Server 2008 R2 Standard Edition onto as a guest OS - but the install hangs at the "Starting Windows" screen when it starts running the installer. Is this is a known issue with the version of Xen we're running (I know it's positively ancient)? Is there a workaround for it at all? We've successfully got a great number of vanilla 2008 servers running on it, it appears it's an issue specific to R2. Bryan

  Read the article

• Oracle Identity Manager ADF Customization

  - by Arda Eralp

  This blog entry includes an example about customization Oracle Identity Manager (OIM) Self Service screen. Before customization all users that can be logged in OIM Self Service can see "Administration" tab on left menu. On this example we create "Managers" role and only users that have managers role can see "Administration" tab. Step 1: Create "Manager" role  Step 2: Create Sandbox  Step 3: Customize ADF Select "Customize" on the top menu Select "Source" instead of "Design" on top  Select "Administration" tab with blue rectangle and edit component Edit "visible" with expression builder #{oimcontext.currentUser.roles['Manager'] != null} Apply Step 4: Apply to All and Publish sandbox Notes:  This table objects can use for expression. Objects Description #{oimcontext.currentUser['ATTRIBUTE_NAME']} #{oimcontext.currentUser['UDF_NAME']} #{oimcontext.currentUser.roles} #{oimcontext.currentUser.roles['SYSTEM ADMINISTRATORS'] != null} Boolean #{oimcontext.currentUser.adminRoles['OrclOIMSystemAdministrator'] != null} Boolean

  Read the article

• Ubuntu 10.10: getting appropiate monitor resolution for lcd hdtv

  - by lurscher

  I'm running Ubuntu 10.10 x86_64 version, with Nvidia 9800 GT, installed 270.41.06 Nvidia drivers following this guide. I have a LG42LH30FR LCD TV connected with the dvi link - RGB PC input I'm able to get 1024x768 resolution without overscan (I can get 1080i = 1366x768 but there is a lot of hidden screen space to the right and I don't know what to do about it). I want to get full HD I can get full HD (1080p = 1920x1080) on Windows XP 64-bit with custom resolution created with Nvidia Control Panel, from reading over xorg.conf configurations it seems I need to add a certain modeling to the monitor configuration, but I don't know where to get the appropriate options for this task any suggestions?

  Read the article

• How to uninstall AMD Display Driver from other install of Windows

  - by nar

  So my Windows 7 had a BSOD from an Ati driver file then restarting only gives me some wierd coloured lines at the top of the screen. Starting in safe mode causes the boot up to freeze at AtiPcie.sys and overlays the same coloured lines on the safe mode start up display. It seems to be a problem with the display driver but I can't get into the OS at all to uninstall it. Luckily I have an old install of Windows 7 from when I moved to a SSD still on my HDD and that runs just fine so I'm pretty sure its a software problem (Maybe the SSD corrupted a driver file or something). So does anyone know how I can uninstall the driver files from another Windows 7 install on the same PC? EDIT: What I mean is, I'm running on the broken PC right now but using a different HDD's windows install. I have full access to the not booting up OS drive with the Windows so I can delete any files/load the registry etc...

  Read the article

• Unable to boot fedora 11

  - by csunwold

  I have been running fedora 11 for several months without a hiccup, but two days ago I ran "yum update" and installed whatever updates were available (I didn't pay attention to what they were). I was having problems with mysql so I tried "yum remove mysql" and then it removed mysql as well as quite a few unexpected dependencies. I then "yum install mysql" without a hitch and went about my way. However, when I next booted up my machine it got to "Starting preload dameon [OK]" and then it hangs with a flashing cursor on the screen. I tried following http://dailypackage.fedorabook.com/i...ling-Grub.html but it didn't seem to make any difference. I put a new hard drive with WinXP on it into the same machine that I booted to, and I tried to use Ext2 Installable File System for Windows but when I run it, it only seems to see /boot and nothing else on the hard drive. Any ideas?

  Read the article

• Music Art Food Drink: Oracle Social Plaza - Tues 10/2

  - by Bob Rhubart

  Join Oracle's social media mavens plus hundreds of your closest friends at this all-social social… What: Oracle Social Plaza When: Tuesday, October 2, 2012Noon to 8:00 pm Where: Mint Plaza Fifth Street between Mission and Market San Francisco It's a full-on treat for all your senses, featuring music, art, food, and fashion. Music will be provided by indy favs Golden State and dance-rageous local DJ Brandon Arnovick. Watch as artists, including Melanie Alveres, create works of art live, then bid on their creations. Want to do a little creating on your own? Try mugging in the Social PhotoBooth. If you're into fashion, 20 local fashion designers will be on hand with their latest creations. And if you like t-shirts, there'll be live screen printing, with free t-shirts for the first 300 guests. Food and drink? Starting at 4:30 pm there will be two bars, along with munchies from one of those outrageous San Francisco food trucks. And don't worry about missing Larry Ellison's keynote. You can watch if from here.

  Read the article

• Trackpad Drag lock pissing me off with Windows 7

  - by rockinthesixstring

  This is driving me insane and I've scowered the web for two days trying to fix this. I just picked up an Apple Magic Trackpad to be used exclusively on a Windows 7 PC (not apple with bootcamp). I found a nice driver that got it working right away, but when I'm moving the cursor around the screen, often it will begin "highlighting" text, or picking up and dragging things I don't want it to. I looked in the "regedit" where people are saying there is binary that can be changed, however the driver I installed doesn't use the binary being suggested. Can anyone suggest a better driver for my situation or a way to disable the drag lock that is driving me so nuts? I don't mind not being able to lift my finger when dragging, it's a far better compromise than having the insane feature.

  Read the article

• Why cant i install ANY operating system??

  - by Ranhiru

  I tested the memory and i tested the hard disk and everything is fine! Mini XP booted from Hirens Boot Disk works :( I tried Windows 7, Windows XP SP3 and even Ubuntu 10.04 :( All Operating Systems boots up to the point where they can load necessary files to start the OS and then resets the laptop Windows 7, only up to the point where the Windows Loading Animation is happening Ubuntu, only up to the point where the loading is done, shows a small screen and then goes to a blinking cursor and thats it... it keeps on blinking and sometimes resets the computer Windows XP SP3, loads all the drivers and everything and then the point where i should be able install the OS, it simply resets the laptop :( I have used the word reset instead of restart because the laptop completely turns off and then only turns back in Any solutions would be greatly appreciated

  Read the article

• Windows XP , HP , IntelInside Trobelshooting

  - by Jamil Hneini

  My Windows XP PC has stopped booting. On start up, before Windows boots a screen appears saying: Windows Could Not Boot: Could Not Find or Corrupted file <Windows root>\Sytem32\Hal.dll Please Reinstall the file... From that I understand that I have to reinstall the OS but my computer is so old that I have lost the backup and recovery disk. My Computer's Info: 32Bit Computer Pentium 4 Windows XP Service Pack 2 HP History: My Computer has 4 hard drives 2 internal 40 GB drives (C And D) 2 external 8GB drives (E And F) Additional Info: I need the files inside C And E The computer reads my flash drive as a hard drive (8.45GB)(I have never booted while my USB pluged in while I was troubleshooting) With some test I discovered that the C drive wasn't detected by the computer I have already configured the boot order of BiOS I have Set The SATA to IDE The Question: I have a setup for windows 8 32 bit how can I boot from my USB to run that setup? If that isn't the proper way to handle this problem please tell me the proper way.

  Read the article

• ProFTPd not in boot: Debian

  - by 50ndr33

  I just configured my new VPS with Apache, PHP, MySQL and ProFTPd. I wanted to install a smtp server, but I was advised to do a apt-get upgrade first. I did this, and I got up a blue screen where I could choose between two alternatives. It said something about GRUB 2 installer. I chose the alternative that was already selected, the topmost. I chose not to update the GRUB2, and use the old one that was installed. Now, ProFTPd doesn't start in boot anymore. I have to /etc/init.d/proftpd start every time. How do I fix this? Should I have chosen to update GRUB2? Should I do apt-get upgrade again and try to do the same GRUB2 installer again?

  Read the article

• How to forward AIM to Gmail

  - by iamjames

  Still have an old AIM email address lying around and would like to forward it to Gmail?  Here's how: 1.  Login to your AIM and click on Settings on the far right 2.  In the left menu click IMAP and POP  3.  This shows you your IMAP and POP setup information for AIM.  We're going to put this into your Gmail account so your Gmail account will check your AIM account and download all AIM emails. 4.  Login to your Gmail, click Settings and click Accounts and Import 5.  Click "Import mail and contacts".  A new window will pop up asking what account you want to import.  Enter your AIM Email Address and click Continue 6.  The next page asks for your password.  Enter your password and click Continue.  Step 2 asks your Import options.  I'd put a checkmark in "Leave a copy of retrieved message on server".  That way all your mail is still stored on AIM if you ever need it. 7.  Click Start import and you're done.  Next screen says it make take several hours up to 2 days before you start seeing imported messages and can check the status at Settings > Accounts and Import

  Read the article

• Sony Bravia KDL-32L5000 PC resolution slightly off

  - by user18818

  I have a PC running two Nvidia 8500 GTs in SLI mode and I am trying to use my TV in dual mode. When I switch the TV to PC the screen is nearly centered with a slight offset. All resolutions are effected from 800x600 all the way up to the TVs native 1360x768. I have tried with SLI on and off and have PhysX turned off as well as I thought that might have an effect. I am running Windows XP 64-bit SP2 DirectX ver 9.0c Nvidia driver version 181.22 Any other information please let me know. Thanks in advance.

  Read the article

• ATI Catalyst setting to stretch Windows XP start bar across both displays

  - by scunliffe

  I have a Lenovo T400 laptop with an ATI Mobility Radeon HD 3400 Series video card, using the ATI Catalyst Control Center to span my Windows XP display over the laptop display and a Dell flatpanel LCD. This works fine, but I'm used to NVIDIA multi-desktop that let me control the "Start bar" to either exist on only 1 screen... be duplicated on both, or (what I want), stretched across both. Is this possible with the ATI card/Catalyst Software? If not, are there any utilities out there that will handle this for me? That is, what I have: +----------+ +----------+ | | | | | Lenovo | | Dell | | (primary)| | | +----------+ | | |Start Tray| | | +----------+ +----------+ And this is what I want: +----------+ +----------+ | | | | | Lenovo | | Dell | | (primary)| | | +----------+ +----------+ |Start | | Tray| +----------+ +----------+

  Read the article

• SOA Suite 11g Purging Guide

  - by ShawnBailey

  We now have a single source of truth concerning Purging in My Oracle Support. The material is contained within the SOA 11g Infrastructure Database: Installation, Maintenance and Administration Guide under the 'Purging' tab. All of the previous purge related content for 11g is now deprecated and many of the documents will redirect to this Guide while others simply contain a disclaimer. What does the Guide contain? Summary Overview of Purging. What it does and why it's important Specific information on each release of 11g Available patches for each release of 11g and recommendations How to run the different purge scripts Tips on improving performance How to begin troubleshooting problems with the process How to identify orphaned records Useful reference information Here are a couple of screen shots to help with navigation: Guide Landing Page: (click image for full view) Select the 'Purging' tab: (click image for full view) The left menu contains the following options: Alternative: Database Partitioning What to do on 11gR1 GA (11.1.1.1) What to do on PS1 (11.1.1.2) What to do on PS2 (11.1.1.3) What to do on PS3 (11.1.1.4) What to do on PS4 (11.1.1.5) Overview of PS5 (11.1.1.6) Purging Step by Step Performance Tips Troubleshooting Purge Orphaned Records Reference This resource goes hand in hand with the excellent documents SOA 11g Database Growth Management Strategy and Start Small, Grow Fast available on OTN. The latest product documentation can be found here.

  Read the article

• Change the update channel in Portable Thunderbird?

  - by rubo77

  I think it needs some explanation How to update a TB Portable installation to beta or aurora. I tried to change the preferences in about:config: update.channel to aurora but that had no effect. Then I edited ThunderbirdPortable3\App\thunderbird\defaults\pref\channel-prefs.js and restarted TB. There I got the message in the Help screen, that I am on update channel aurora, which seems fine. Still: the update downloaded Thunderbird 29 pre beta and tried to install but ended with the message that it couldnt be installed due to patch problems: Das Update konnte nicht installiert werden (Patch-Anwendung fehlgeschlagen) I tried this again with the channel "nightly" and got the same error. (On channel "beta" there seem to be no newer version than in the channel "release".) How can I change my installation to channel aurora and update it?

  Read the article

• Refining an AutoHotkey script

  - by roy2012

  The purpose of this script is: The first two rows of hotkeys always effective. The remaining hotkeys work at NO TEXT INPUT Status only. In other words, when the small vertical lines are flashing anywhere on the screen and waiting for input text / digital, press zxasq, the effect is equal to the normal original letters. How can I do that? Rwin::^space AppsKey::^w CapsLock::MButton z::PgUp x::PgDn *a up::send {shift up}{ctrl up}{LButton up} *a:: GetKeyState, LButtonState, LButton ; if LButtonState = U ; send {shift down}{ctrl down}{LButton down} ; return *s up::send {shift up}{ctrl up}{RButton up} *s:: GetKeyState, RButtonState, RButton ; if RButtonState = U ; send {shift down}{ctrl down}{RButton down} ; return *q up::send {shift up}{ctrl up}{MButton up} *q:: GetKeyState, MButtonState, MButton ; if MButtonState = U ; send {shift down}{ctrl down}{MButton down} ; return

  Read the article

• Why doesn't unity show icons or panel after installing numix theme?

  - by Sid

  I'm a beginner to Ubuntu/Linux and I have a problem: Unity is not loading! When I choose Unity in the log-in screen, I get notifications and I can see the mouse, but that's it. I have Ubuntu 14.04 installed, along with Bumblebee/Primus. I had no issues whatsoever, until I decided to try the numix-theme and the numix icon pack. I added the PPA and installed it, but when I logged off and logged back on, nothing showed up. I panicked, and in tty1, I purged numix-* but that did not solve the issue. To get by day-to-day use, I installed gnome-flashback, and among those environments, only the metacity one works. (The compiz one does not.) I've tried installing the unity-tweak-tool to reset unit, installing dconf and doing: dconf reset -f /org/compiz/ but that didn't work either. One site even told me to delete /org/compiz/, but that did not resolve the issue. When I checked ccsm, the Unity plugin had a check to it. I also tried with Unity doesn't load, no Launcher, no Dash appears, but it gets stuck on "loading icons". Any help will be awesome!

  Read the article

• Where does the information shown by OS X Terminal 'Display all commands' feature come from?

  - by Sergio Acosta

  I just learned that if you hit and hold ESC while on the Mac Terminal, a prompt appears after a few seconds offering to show every command available on your system, including aliases, built-ins, and executables on your PATH. Soruce: http://www.mactricksandtips.com/2008/05/list-all-possible-terminal-commands.html However, the output is show through a more filter, and I cannot grep it or pipe it to another command. Does anyone know how this magic output is generated? Is it just generated on the fly by Terminal? Is there a bash command that can be called explicitly on the command line and get the same result? It is mostly curiosity, but I would love to be able to get the results as text I can post-process and not just browse on screen.

  Read the article

• How can I to take an HDMI TV broadcast and overlay text in real time?

  - by ObligatoryMoniker

  Our company wants to be able to have LCD TVs displaying TV with the ability to add an overlay, like a stock ticker at the bottom of the screen, where human resources can add content to be displayed. I have been trying to nail down the correct terminology for this and come across terms like Keying, Compositing, Live Broadcast Graphics Presentation, and Hardware Overlay but I don't know which of these terms is truly the correct way to refer to what I am trying to do. Black Magic offers a product that seems like it can do what I am looking for but their product seems like it is geared for a totally different purpose than what I would be using it for. Compix also seems to have a product that would do what I need but again it seems like killing a fly with a sledge hammer. How can I to take an HDMI TV broadcast and overlay arbitrary content in real time?

  Read the article

• GPU based procedual terrain borders?

  - by OnePie

  I'm working on a game that preferibly should feature a combination of designed and procedually generated terrain where the designer specifies in somewhat detailed terms what type of terrain a given area will have (grasslands, forest etc...) and then a precedual algorithm takes care of the rest. I'm not talking about minecraft style biomoes, but rather the game map for a strategy game. Each 'area' will not take up that much of the screen, and thus be more akin to a tile whose texture is procedually generated. While procedually generating terrain textures on the GPU are not that difficult, the hard part is making the borders between them look good. Currently, the 'tiles' are large enough to be visible (due to memory constraints mainly, we are talking planetary sized textures for a game taking place in space and on a continental ground view with seamless transitions between them) and creating good borders between them with an algorithm that is fast enough to be useful has proven difficult. Sampling the n-surrounding pixels and using the combiened result did not yield very good borders and was fairly slow on the GPU to boot (ca 12ms for me, that is without any lighning or shading and with very simple terrain texture shaders). So are there any practical known methods to solve this problem?

  Read the article

• Webcam doesn't work in Ubuntu 12.10

  - by Kzhi

  I have Gembird cam68ut. On my Ubuntu 12.10 it shows black screen in cheese and guvcview. I tested it in win7, it works fine. Here what I found: It is a uvc compliant camera, I checked on the site: 18ec:3299 USB 2.0 PC Camera (model number QC3231) ArkMicro This webcam is report by lsusb: Bus 001 Device 004: ID 18ec:3299 Arkmicro Technologies Inc. Here is the output of dmesg | tail: uvcvideo: Found UVC 1.00 device USB2.0 PC CAMERA (18ec:3299) uvcvideo: UVC non compliance - GET_DEF(PROBE) not supported. Enabling workaround. input: USB2.0 PC CAMERA as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.5/1-1.5:1.0/input/input17 usbcore: registered new interface driver uvcvideo USB Video Class driver (1.1.1) When I run cheese (or guvcview), here what I get in terminal: libv4l2: error turning on stream: No space left on device (cheese:11797): cheese-WARNING **: Internal data flow error. I tried it on different usb slots with the same results The Webcam's microphone works, I can record audio with it Guys, any thoughts on what can be done to make it work?

  Read the article

< Previous Page | 468 469 470 471 472 473 474 475 476 477 478 479  | Next Page >