Search Results

Search found 14738 results on 590 pages for 'outlook settings'.

Page 488/590 | < Previous Page | 484 485 486 487 488 489 490 491 492 493 494 495  | Next Page >

• How do I stop panning on a monitor that supports a specific resolution?

  - by IronicMuffin

  Hi all, I've been battling this for a few days now. Any and all help is appreciated. I have a planar monitor with a native res of 1280x1024. At one point, I had used PowerStrip to override "something" and set the res to 1600x1200, and it worked great. I then installed new intel graphics drivers for my 86895g (or w/e model) video card, which screwed up whatever settings I had. If I set it to 1600x1200 this time, it would set the res correctly, but give me a 1280x1024 viewport and the screen would pan when the mouse got to the edges of the screen. Absolutely not useful. Ok, so I was limited to 1280x1024 now. W/e. Now...enter new video card with two video ports. I have two monitors now and the latest nVidia drivers. I decide to try to get dual 1600x1200 going...ended up screwing the original monitor up so much now that it's at 1280x1024, with a 1024x768 viewport and panning! Absolutely not usable now. So what I need, and I can't seem to find on any forums, is help doing one or more of the following: Clearing out all monitor/edid info out of the windows registry without corrupting the registry. Actually correctly override the EDID values and get my sweet res back. Some other way of getting back to at least dual 1280x1024 with NO panning. Note: My device manager shows 4 monitors for some reason. My registry shows entries for all sorts of monitors that have been hooked up to the machine over the years. It's making it difficult to debug. Experience with PowerStrip would be helpful. I've been mucking with Phoenix EDID designer and MonInfo as well, but I'm stumbling around in the dark with these. Windows XP SP2 nVidia GeForce 6200 nVidia drivers: v258.96 Monitor: Planar PL 1910M Thanks!

  Read the article

• APC fragmentation on EC2 Micro for Wordpress + W3TC

  - by Maarten Provo

  I'm trying to optimize APC for my Amazon EC2 Micro server running one Wordpress-site with W3TC. I've started with the settings advised by TechZilla in another topic but I keep getting high fragmentation with 50% of space being free. I've uploaded an image to http://www.maartenprovo.be/downloads/apc.jpg but I can't post it here since I need at least 10 reputation. What values can I optimize to prevent fragmentation? [apc] apc.enabled=1 apc.shm_segments=1 ;32M per WordPress install apc.shm_size=164M ;Leave at 2M or lower. WordPress does't have any file sizes close to 2M apc.max_file_size=2M ;Relative to the number of cached files apc.num_files_hint=1000 ;Relative to the size of WordPress apc.user_entries_hint=4096 ;The number of seconds a cache entry is allowed to idle in a slot before APC dumps the cache apc.ttl=7200 apc.user_ttl=7200 apc.gc_ttl=3600 ;Auto update chache files on change in WP-ADMIN or W3TC apc.stat=1 ;This MUST be 0, WP can have errors otherwise! apc.include_once_override=0 ;Only set to 1 while debugging apc.enable_cli=0 ;Allow 2 seconds after a file is created before it is cached to prevent users from seeing half-written/weird pages apc.file_update_protection=2 ;Ignore files apc.filters apc.slam_defense = 0 apc.write_lock = 1 apc.cache_by_default=1 apc.use_request_time=1 apc.mmap_file_mask=/var/tmp/apc.XXXXXX apc.stat_ctime=0 apc.canonicalize=1 apc.write_lock=1 apc.report_autofilter=0 apc.rfc1867=0 apc.rfc1867_prefix =upload_ apc.rfc1867_name=APC_UPLOAD_PROGRESS apc.rfc1867_freq=0 apc.rfc1867_ttl=3600 apc.lazy_classes=0 apc.lazy_functions=0

  Read the article

• Windows 7 remote desktop encryption error every few minutes

  - by rfrankel

  Because of an error in data encryption, this session will now end. This is the error I've been getting more and more frequently over the past few days, to the point that I can't ignore it because it's happening consistently within 5 minutes of connecting - sometimes within a few seconds. Both the remote and local machines are Windows 7 Pro x64. The remote machine is behind a Linksys RV082, and I'm using UPnP to forward a remote port to the correct local port. This setup had been working fine for several months, and I can't think of any recent relevant changes that might have been made. Things I've already tried: Disabling unnecessary components of the network connection on the remote machine, until only IPv4 and Client for Microsoft Networks remain. Disabling TCP large send offload on both the remote and local machines. Confirming that the remote machine is not mentioned anywhere in any DMZ settings on the Linksys router. Confirming that there are no x509-related registry keys screwing things up (this is the suggested fix for a slightly different error anyway). These are the only solutions I've been able to find after about an hour of searching, and most of them apply to XP or Server 2003 in any case. If anyone could suggest something else, it would be much appreciated.

  Read the article

• Gnome-panel disappearance in Ubuntu 10.10

  - by jurchiks

  Just today, after about a week of somewhat normal running (I'm a total beginner in Linux and the level of amazingly stupid problems I encountered made me go nuts), today my panel disappeared (the one with Applications/System menus, you'd call it taskbar in Windows). Also, Alt+F2 doesn't work and Ctrl+Alt+Backspace has no effect (I'd think it's supposed to do something). I tried the solution posted here: Panel doesn't show at startup at Ubuntu 10.04 No luck, didn't change absolutely anything. I also couldn't find the .gconf and .gconfd folders using search, so couldn't try that option. There were ones that had same names but without the dot though, but there were several so I didn't risk. What could possibly be the reason for this? All I did yesterday was try to install some updates (another extremely dumb problem - doesn't allow to install even the official updates - "insecure sources" or smth like that, tried fixing it with some tutorials on the net but in the end it worked only for half a day and went back to refusal mode :@) and very few tools from the Ubuntu Software Center, but nothing that would change system settings just by installing it.

  Read the article

• I think installing PostFix solved my problem, but it seemed *too* easy

  - by Joel Marcey

  Hi, This is a followup to a serverfault post I made a while ago: http://serverfault.com/questions/21633/how-do-i-target-a-different-mail-server-depending-on-domain-with-exim (More context here too: http://forum.slicehost.com/comments.php?DiscussionID=3806 ) I have a slice/VPS at Slicehost. I basically decided to scrap exim (i.e., purge it), and start anew with my email infrastructure. In case you didn't read any of the above threads, basically my goal was to have a send only mail infrastructure that relays all outgoing email to Google Apps. I also wanted to where email from domain1 (a Wordpress installation) would show it coming from domain1.com and email from domain2 (a normal website) would show it coming from domain2.com. So I decided to give PostFix a try. I literally followed the surprisingly simple instructions here: http://sudhanshuraheja.com/2009/02/slicehost-setup-outgoing-mail-google-apps-postfix/ And voila, all seems to be working as I expected. My email tests show email coming from the proper locations (either domain1 or domain2 depending on where the emails were sent from). But this all seemed too simple to me. So simple, in fact, that I feel that something is amiss. When I installed PostFix according to the instructions in the post above and it worked, I was surprised that I didn't have to specify an SMTP server, a port number, any authentication credentials, etc. My slice is set up such that I have MX records for Google Apps (e.g., ASPMX.L.GOOGLE.COM.) in my DNS settings, but I am not sure if that is why it is working. My email infrastructure knowledge is admittedly limited, but with this am I suspect to: Spammers using my email infrastructure? My emails going to people as spam? Something else sinister? I have actually stopped running PostFix until I understand this better. Thanks!

  Read the article

• How to figure out what VirtualBox did?

  - by AndrejaKo

  I'm trying to boot a custom made-in-ASM OS on my recent laptop. The OS is intended to be installed on a floppy and during make creates a bootable floppy. Since I don't have a floppy drive, I installed it on a virtual floppy. After that I used WinToFlash's create bootable MS-DOS USB drive option to transfer the floppy image to an USB flash drive. Then I tried to boot my computer from it but got only a repeating broken string on screen. After all that I made a virtual hard disk image form the flash drive using this tutorial and tried to boot a virtual machine from it. First time I got same problem as on real computer. I then used the reset option and next time and every time after that OS booted correctly. My question is: How do I figure out what exactly happened to the virtual machine between first and second boot? UPDATE I just created a new VM with default settings for windows XP and it has the same problem that I have on a real computer. I was unable to reproduce the procedure which made the first VM work correctly.

  Read the article

• Postfix misconfigured? 550 Sender rejected from recieving server

  - by wnstnsmth

  We use Postfix on our CentOS 6 machine, having the following configuration. We use PHP's mail() function to send rudimentary password reset emails, but there is a problem. As you will see, mydomain and myhostname is correctly set, afaik. alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases command_directory = /usr/sbin config_directory = /etc/postfix daemon_directory = /usr/libexec/postfix data_directory = /var/lib/postfix debug_peer_level = 2 html_directory = no inet_interfaces = localhost inet_protocols = all mail_owner = postfix mailq_path = /usr/bin/mailq.postfix manpage_directory = /usr/share/man mydestination = $myhostname, localhost.$mydomain, localhost mydomain = ***.ch myhostname = test.***.ch newaliases_path = /usr/bin/newaliases.postfix queue_directory = /var/spool/postfix readme_directory = /usr/share/doc/postfix-2.6.6/README_FILES sample_directory = /usr/share/doc/postfix-2.6.6/samples sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop unknown_local_recipient_reject_code = 550 Now this is the stuff that is in the /var/log/maillog of Postfix upon sending an email to ***.***@***.ch, with ***.ch being the same domain our sending server test.***.ch is on: Dec 13 16:55:06 R12X0210 postfix/pickup[6831]: E6D6311406AB: uid=48 from=<apache> Dec 13 16:55:06 R12X0210 postfix/cleanup[6839]: E6D6311406AB: message-id=<20121213155506.E6D6311406AB@test.***.ch> Dec 13 16:55:07 R12X0210 postfix/qmgr[6832]: E6D6311406AB: from=<apache@test.***.ch>, size=1276, nrcpt=1 (queue active) Dec 13 16:55:52 R12X0210 postfix/smtp[6841]: E6D6311406AB: to=<***.***@***.ch>, relay=mail.***.ch[**.**.249.3]:25, delay=46, delays=0.18/0/21/24, dsn=5.0.0, status=bounced (host mail.***.ch[**.**.249.3] said: 550 Sender Rejected (in reply to RCPT TO command)) Dec 13 16:55:52 R12X0210 postfix/cleanup[6839]: 8562C11406AC: message-id=<20121213155552.8562C11406AC@test.***.ch> Dec 13 16:55:52 R12X0210 postfix/bounce[6848]: E6D6311406AB: sender non-delivery notification: 8562C11406AC Dec 13 16:55:52 R12X0210 postfix/qmgr[6832]: 8562C11406AC: from=<>, size=3065, nrcpt=1 (queue active) Dec 13 16:55:52 R12X0210 postfix/qmgr[6832]: E6D6311406AB: removed Dec 13 16:55:52 R12X0210 postfix/local[6850]: 8562C11406AC: to=<root@test.***.ch>, orig_to=<apache@test.***.ch>, relay=local, delay=0.13, delays=0.07/0/0/0.05, dsn=2.0.0, status=sent (delivered to mailbox) Dec 13 16:55:52 R12X0210 postfix/qmgr[6832]: 8562C11406AC: removed So the receiving server rejects the sender (line 4 of log output). We have tested it with one other recipient and it worked, so this problem might be completely unrelated to our settings, but related to the recipient. Still, with this question, I want to make sure we're not making an obvious misconfiguration on our side.

  Read the article

• Why is lighttpd and fastcgi keeping sending me the *.scgi file instead of the website content?

  - by e-satis

  I have the following config: server.modules = ( "mod_compress", "mod_access", "mod_alias", "mod_rewrite", "mod_redirect", "mod_secdownload", "mod_h264_streaming", "mod_flv_streaming", "mod_accesslog", "mod_auth", "mod_status", "mod_expire", "mod_fastcgi" ) [...] fastcgi.server = ( ".php" => (( "bin-path" => "/usr/bin/php-cgi", "socket" => "/var/tmp/lighttpd/php-fastcgi.socket" + var.PID, "max-procs" => 1, "kill-signal" => 9, "idle-timeout" => 10, "bin-environment" => ( "PHP_FCGI_CHILDREN" => "200", "PHP_FCGI_MAX_REQUESTS" => "1000" ), "/pyapps/essai/blondes.fcgi" => ( "main" => ( "socket" => "/var/tmp/lighttpd/django-fastcgi.socket", ), ), "bin-copy-environment" => ( "PATH", "SHELL", "USER" ), "broken-scriptfilename" => "enable" ))) [...] $HTTP["host"] =~ "(^|www\.)cam\.com(\:[0-9]*)?$" { server.document-root = "/home/cam/web/" accesslog.filename = "/home/cam/log/access.log" server.errorlog = "/home/cam/log/error.log" server.follow-symlink = "enable" # files to check for if .../ is requested server.indexfiles = ( "index.php", "index.html", "index.htm", "index.rb") url.rewrite = ( "^(/blondes/.*)$" => "/pyapps/essai/blondes.fcgi$1" ) } I have the following dir tree: /home/tv/web/ `-- pyapps `-- essai `-- __init__.py `-- blondes.fcgi `-- blondes.pid `-- django-fcgi.py `-- manage.py `-- manage.pyo `-- plop `-- settings.py `-- urls.py No error when restarting lighthttpd. The I run: ./manage.py runfcgi method=prefork socket=/var/tmp/lighttpd/django-fastcgi.socket daemonize=false pidfile=blondes.pid No errors neither. I then go to http://cam.com/blondes/. I offers me to download an empty file. I checked permissions but everything is set to the same user and group, and they work for the PHP site. The file /var/tmp/lighttpd/django-fastcgi.socket exists. When I reload the page, I got no output in error logs, nor in the manage.py runfcgi command. I probably missed something obvious, but what ?

  Read the article

• PostgreSQL pg_hba.conf with "password" auth wouldn't work with PHP pg_connect?

  - by tftd

  I've recently experimented with the settings in pg_hba.conf. I read the PostgreSQL documentation and I though that the "password" auth method is what I want. There are many people that have access to the server PostgreSQL is working on so I don't want the "trust" method. So I changed it. But then PHP stopped working with the database. The message I get is "Warning: pg_connect(): Unable to connect to PostgreSQL server: FATAL: password authentication failed for user "myuser" in /my/path/to/connection/class.php on line 35". It is kind of strange because I can connect via phppgadmin without any problems and also I can connect from my home computer with psql - again without any problems. This is my pg_hba.conf: # TYPE DATABASE USER CIDR-ADDRESS METHOD # "local" is for Unix domain socket connections only local all all password # IPv4 local connections: host all all 127.0.0.1/32 password # IPv6 local connections: host all all ::1/128 password The connection string I'm using with pg_conenct is: $connect_string = "host=localhost port=5432 dbname=mydbname user=auser password=apassword"; $dbConnection = pg_connect($connection_string); Does anybody know why is this happening ? Did I misconfigured something ?

  Read the article

• VPN messes up DNS resolution

  - by user124114

  After connecting with the Kerio VPN client (OS X Leopard) to a server, the internet (~web browsing) stopped working for the client. After poking around, the issue seems to be bad DNS server (i.e., entering IPs directly works). After disconnecting from the VPN, the invalid DNS server disappears from scutil --dns and all's well again. Now, I don't understand why OS X on the client even changes the DNS settings -- internet should be routed through a different interface, through the default gateway, not through the VPN. Questions: By what mechanism does connecting the VPN client change the "default" DNS server? How can I stop the VPN client from changing routing/DNS rules? Where is this stuff stored/modified? Before VPN: $ scutil --dns DNS configuration resolver #1 nameserver[0] : 10.66.77.1 # <---- default gateway = home router; all good order : 200000 resolver #2 domain : local options : mdns timeout : 2 order : 300000 ... VPN connected: $ scutil --dns DNS configuration resolver #1 nameserver[0] : 192.168.1.1 # <--- rubbish nameserver[1] : 192.168.2.1 order : 200000 resolver #2 domain : local options : mdns timeout : 2 order : 300000 ... The VPN doesn't appear among $ networksetup -listallnetworkservices.

  Read the article

• Computer turns itself on after any off mode

  - by Patrick

  Whenever I shut down my computer, or put it in sleep/hybernate, it turns on after two seconds. It doesn't post, it just powers on and then idles. To actually turn it off, I switch off the psu. The problem is now, whenever I switch the psu on and try to boot, it doesn't always turn on. It takes a good amount of flicking the psu switch on and off before the motherboard lights up. So far I've determined the things its not: its not caused by the mouse or network waking up the computer. I've been able to go into hybernate for the past year. And all "wake on X" settings in the bios are diabled. its not a scheduled task waking up the computer at a given hour, it occurs every single time its not due to an upgrade or new installation, since I haven't done either in a very long time I'm sure its a hardware issue. So I'd like to know, is my psu dead, or the motherboard? The psu is an Antec Earthwatts 600w, the motherboard is an Asus P5Q-E, both one year old.

  Read the article

• Google account gives ERR_SSL_BAD_RECORD_MAC_ALERT errors

  - by Kjensen

  A couple of days ago, I started being unable to connect to accounts.google.com, which handles logins to all kinds of google services. I get this error in Chrome: Error 126 (net::ERR_SSL_BAD_RECORD_MAC_ALERT): Unknown error. In IE I get this: I assume it is the same error, just wrapped up. I run Win8 RTM. On the SAME machine, using the same network card, in a VMWare workstation image running Win7, I am able to connect perfectly. On another of my machines on my network, I am also still able to connect with no problem. My girlfriend uses the same network and has also complained a couple of times about this error (google calendar) - but this is anecdotal, since her technical troubleshooting abilities stop at "xxxx is broken". Her machine runs Win7. ;) I have rebooted, cleared cookies, do not run any antivirus/firewall, have not changed network config. The first 3-4 days after installing Win8, I did not have any problems. I have also searched, and found a hint about enabling SSL2.0 in connection settings, which did not help. Anybody know something about this error and what I can do to fix it?

  Read the article

• How can I password protect an IIS directory with only FTP access?

  - by Tony Adams

  How can I password protect an IIS directory when I only have FTP access to the server? I can't adjust any IIS settings or add users or anything like that. The answer to: IIS Basic Authorization ala .htaccess/.htpasswd in apache does not help as I only have access to the server via FTP. I just need to password protect a directory. I've tried several variations of a web.config file. I can get a basic HTTP auth form to pop up when a user attempts to load a page from my test directory, but I can't configure the authentication part. The server complains that: Parser Error Message: It is an error to use a section registered as allowDefinition='MachineToApplication' beyond application level. This error can be caused by a virtual directory not being configured as an application in IIS. whenever I add an <authentication> section to my web.config. I'm grateful for any help anyone can offer. Edit: I don't know what version of IIS is running on this server, but here is the server tag from error messages: Version Information: Microsoft .NET Framework Version:1.1.4322.2490; ASP.NET Version:1.1.4322.2494

  Read the article

• System Slow After Uprading Ubuntu

  - by Aragon N

  I have an Ubuntu network machine which has release of 10.04.1 LTS Lucid. On this system I have Apache, PostgreSQL and django. For some app. development I have to install PGP and php-curl. Due to being on network, I have exported a VMware machine to the Internet and firstly I have upgraded the system and then installed php5 packages on it. I don't know is it all about django or apache configuration. Maybe some Apache settings had changed. In this case in apache where I have to look at ? After all replacing it with its old place, I see that the new system query is slow according to another. Old system query time : 140 ms New system query time : 9.11 s I have checked /etc/network interface and it seems there is no problem. I have checked /etc/resolv.conf and it seems OK I have checked /etc/nsswitch.conf and only host section is different from old one which old system has hosts: files mdns4_minimal [NOTFOUND=return] dns mdns4 and then I have checked time host -t A services.myapp.com and I got real 0m0.355s user 0m0.010s sys 0m0.020s and I have checked apache2 HostnameLookups : find /etc/apache2/ -type f | xargs grep -i HostnameLookups It returned : /etc/apache2/apache2.conf:# HostnameLookups: Log the names of clients or just their IP addresses /etc/apache2/apache2.conf:HostnameLookups Off and now what can I have to check for boosting my system as before?

  Read the article

• MySQL Config on Large Machine

  - by Jonathon

  We have a Windows 2003 Enterprise Edition server (64bit) running only MySQL 5.1.45 64-bit. It has 16G RAM and 10T of hard-drive space in RAID 10. We are having horrible performance from mysqld (85-100% CPU utilization). We were running a smaller machine with better performance, so I am assuming our my.ini file is not correct for our current machine. The my.ini file is as follows: [client] port=3306 [mysql] default-character-set=latin1 [mysqld] port=3306 basedir="D:/MySQL/" datadir="D:/MySQL/data" default-character-set=latin1 default-storage-engine=MYISAM sql-mode="" skip-innodb skip-locking max_allowed_packet = 1M max_connections=800 myisam_max_sort_file_size=5G myisam_sort_buffer_size=500M table_open_cache = 512 table_cache=8000 tmp_table_size=30M query_cache_size=50M thread_cache_size=128 key_buffer_size=3072M read_buffer_size=2M read_rnd_buffer_size=16M sort_buffer_size=2M #replication settings (this is the master) log-bin=log server-id = 1 Does anyone see anything wrong with this setup? For a machine with this much RAM, why in the world would mysqld eat up so much CPU? I know we can optimize some queries, etc., but it did run okay on a smaller machine, so I am pretty sure it is the config. Thanks in advance for any help.

  Read the article

• SATA Driver for Acer Aspire One D257

  - by Robert Niestroj

  i have a Acer Aspire One D257. In this netbook the hard disk is defect so i bought a new one. Now i want to reinstall Windows 7. Im using an external DVD Drive plugged into USB. The Windows 7 DVD is staring, Win7 setup is starting and when it comes to Hard Drive options it says that no drive was detected and i should try search for drivers. It shows me this window: Screenshot from web Now i cant find the right drivers for this netbook to continue with the installation. The laptop has the newest BIOS - 1.15, it is reset to factory default settings except that i enabled the Boot Menu prompt with F12. From the Acer Support Website i've downloaded the SATA AHCI Driver and the Chipset Driver. I unpacked both to a USB flashdrive in seperate folders. When i select the SATA AHCI Driver it does not find any drivers. When i uncheck the checkbox "Hide drivers that are not compatible with hardware on this computer" it shows one driver: Acer HWID (path_to\1.inf). When i continue with this driver i got an error message that says something like: No new devices found. Check if the driver files are on the installation disk. When i show him the Chipset Driver it sees a lot more driver. When i uncheck the checkbox "Hide drivers that are not compatible with hardware on this computer" it show some drivers: Intel N10 Family DMI Bridge Intel N10/ICH7 Family PCI Express Root Port Intel N10/ICH7 SMBUS Controller Intel N10/ICH7 Family USB Universal Host Controller Intel N10/ICH7 Family USB2 Enhanced Host Controller Intel N10/ICH7 Family Interface LPC Controller When i uncheck this checkbox i get a lot more drivers, and some SATA Drivers but the also do not work. I get the same error message as before. Can someone help me find a driver that should work or am i doing anything else wrong?

  Read the article

• Barriers to IPv6 deployment: addressing

  - by sysadmin1138

  There are several things that are keeping IPv6 deployment from being a topic of active discussion here at my work. There are the usual technical issues, but one non-technical one appears to be a major stumbling block on the path to actually getting a deployment project going. Addresses, memorizing of. Specifically, IPv4 addresses are comprehensible, and IPv6 addresses just look like a big long string of hex. The human mind has real trouble memorizing lists of more than 7-8 items, and an IPv4 address (192.168.231.148) has four items in it which makes it easy for us to memorize. A fully populated IPv6 address has not only 8 sections, but each section has 4 hex digits in it. IPv6 addresses were not designed for memorization. To the technician who knows that the DNS server is at 192.168.42.42 (or more likely "42.42", since the company prefix is likely memorized), the idea of memorizing an IPv6 address fills them with dread. Which in turn makes them much less enthusiastic about participating in an IPv6 deployment project. Because of how our network works we're not fully dynamic in terms of v4 addressing. We have several to many subnets that are entirely statically assigned for a variety of reasons, chief among them being that the overhead of static DHCP assignments is perceived as being too great. Also, some devices still aren't smart enough to pull DNS addresses out of DHCP while also having a static assignment, and therefore require manually configured DNS settings. Therefore, some v6 address memorization will have to be done. We're not under any mandate to get v6 out the door, so we don't have pressure from the top. However, it is time to start prepping our infrastructure to handle IPv6 even if we don't convert wholesale. For those of you who have been in IPv6-land for a while, what short-cut methods do you use to discuss or keep track of subnets and specific/critical IP addresses? If I can help reduce some of the dread surrounding IPv6 we might get the project going.

  Read the article

• Shut Out of XP - No Admin Password or CDR

  - by ashes999

  I inherited an old WinXP/Linux dual-boot machine from the stoneage. Because it has Linux, the regular boot process is replaced with the Fedora boot loader; I cannot, therefore, press F8 strategically to tell my PC to boot from CD. Even if I could, it's a moot point; the CDR doesn't seem to recognize any CDs. To make things worse, there's no option to network boot. The original user is probably long gone; I don't know the password for any of the Administrator group users. I can login using my corp account, but that's unprivileged on this machine. Since I'm not an admin, I can't do crazy things, like looking at boot.ini. Or deleting files. I only have 500MB free on my C drive. I'm pretty sure I can't boot from a USB, since I didn't see any settings for this in my BIOS. How can I get admin access for my user? Edit: Things I've tried: Boot from CD (CD not recognized) Launch CD from XP (CD not recognized) Install Daemon Tools Lite so I can install from an ISO -- don't have admin privileges XP password recovery tool -- requires admin privileges Adding an admin user -- no access to Control Panel Users since I'm not an admin Logging in as both the admin users on the system (trying some standard passwords) Using Fedora to chntpw (the Fedora version installed is ancient -- 2.7)

  Read the article

• How to create a static IP on Windows Server 2008 R2 so I can access the server remotely

  - by Aesir

  I have just purchased a HP Proliant N40L which I am intending to use as a NAS, learning tool and just in general something to mess around with. As a student via the Microsoft dreamspark program I can get a free copy of Windows Server 2008 R2 which I am using as the OS. So that I can remote to the box from outside of my local network and so that I can stream media from it to my PS3, I have read that I need to create a static IP for the server and use port forwarding to forward to this IP so I can remote in. Is this correct? I am not really sure how to do this and if I need to make these changes on my router configuration, on the OS or both. I am a novice when it comes to networking however most resources for Windows server 2008 R2 seem to assume a fair amount of experience already. I realise that using this particular OS may seem like overkill for what I currently wish to do with it (stream content to other devices and backup) but as I can get a copy for free it seems sensible. Edit: From reading answers posted I feel I should give more information. I have now tried to add a static IP address using my router configuration settings. I have used the getmac command to get the mac address of the server. My ISP is Virgin Media and I have gone to the LAN IP section and I have added an IP address to the DHCP Reservation Lease Info. I can now use remote desktop connection internally to remote to the server (so I am assuming assigning this IP has worked). How do I configure this on the OS as well? I am also unsure on how I would remote to this machine outside of my local network?

  Read the article

• mysqld crashes on any statement

  - by ??iu

  I restarted my slave to change configuration settings to skip reverse hostname lookup on connecting and to enable the slow query log. I edited /etc/my.cnf making only these changes, then restarted mysqld with /etc/init.d/mysql restart All appeared to be well but when I connect to msyqld remotely or locally though it connects okay a slight problem is that mysqld crashes whenever you try to issue any kind of statement. The client looks like: Reading table information for completion of table and column names You can turn off this feature to get a quicker startup with -A Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 3 Server version: 5.1.31-1ubuntu2-log Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> show tables; ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... Connection id: 1 Current database: mydb ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... ERROR 2003 (HY000): Can't connect to MySQL server on 'xx.xx.xx.xx' (61) ERROR: Can't connect to the server ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... ERROR 2003 (HY000): Can't connect to MySQL server on 'xx.xx.xx.xx' (61) ERROR: Can't connect to the server ERROR 2006 (HY000): MySQL server has gone away Bus error The mysqld error log looks like: 101210 16:35:51 InnoDB: Error: (1500) Couldn't read the MAX(job_id) autoinc value from the index (PRIMARY). 101210 16:35:51 InnoDB: Assertion failure in thread 140245598570832 in file handler/ha_innodb.cc line 2595 InnoDB: Failing assertion: error == DB_SUCCESS InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/refman/5.1/en/forcing-recovery.html InnoDB: about forcing recovery. 101210 16:35:51 - mysqld got signal 6 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=3 max_threads=600 threads_connected=3 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x18209220 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f8d791580d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f902a76a080] /lib/libc.so.6(gsignal+0x35) [0x7f90291f8fb5] /lib/libc.so.6(abort+0x183) [0x7f90291fabc3] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x41b) [0x781f4b] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f902a7623ba] /lib/libc.so.6(clone+0x6d) [0x7f90292abfcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x18213c70 = thd->thread_id=3 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash. 101210 16:35:51 mysqld_safe Number of processes running now: 0 101210 16:35:51 mysqld_safe mysqld restarted InnoDB: The log sequence number in ibdata files does not match InnoDB: the log sequence number in the ib_logfiles! 101210 16:35:54 InnoDB: Database was not shut down normally! InnoDB: Starting crash recovery. InnoDB: Reading tablespace information from the .ibd files... InnoDB: Restoring possible half-written data pages from the doublewrite InnoDB: buffer... 101210 16:35:56 InnoDB: Started; log sequence number 456 143528628 101210 16:35:56 [Warning] 'user' entry 'root@PSDB102' ignored in --skip-name-resolve mode. 101210 16:35:56 [Warning] Neither --relay-log nor --relay-log-index were used; so replication may break when this MySQL server acts as a slave and has his hostname changed!! Please use '--relay-log=mysqld-relay-bin' to avoid this problem. 101210 16:35:56 [Note] Event Scheduler: Loaded 0 events 101210 16:35:56 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.31-1ubuntu2-log' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu) 101210 16:36:11 InnoDB: Error: (1500) Couldn't read the MAX(job_id) autoinc value from the index (PRIMARY). 101210 16:36:11 InnoDB: Assertion failure in thread 139955151501648 in file handler/ha_innodb.cc line 2595 InnoDB: Failing assertion: error == DB_SUCCESS InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/refman/5.1/en/forcing-recovery.html InnoDB: about forcing recovery. 101210 16:36:11 - mysqld got signal 6 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=1 max_threads=600 threads_connected=1 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x18588720 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f49d916f0d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f4c8a73f080] /lib/libc.so.6(gsignal+0x35) [0x7f4c891cdfb5] /lib/libc.so.6(abort+0x183) [0x7f4c891cfbc3] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x41b) [0x781f4b] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f4c8a7373ba] /lib/libc.so.6(clone+0x6d) [0x7f4c89280fcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x18599950 = thd->thread_id=1 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash. 101210 16:36:11 mysqld_safe Number of processes running now: 0 101210 16:36:11 mysqld_safe mysqld restarted The config is [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] innodb_file_per_table innodb_buffer_pool_size=10G innodb_log_buffer_size=4M innodb_flush_log_at_trx_commit=2 innodb_thread_concurrency=8 skip-slave-start server-id=3 # # * IMPORTANT # If you make changes to these settings and your system uses apparmor, you may # also need to also adjust /etc/apparmor.d/usr.sbin.mysqld. # user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /DB2/mysql tmpdir = /tmp skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. #bind-address = 127.0.0.1 # # * Fine Tuning # key_buffer = 16M max_allowed_packet = 16M thread_stack = 128K thread_cache_size = 8 # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP max_connections = 600 #table_cache = 64 #thread_concurrency = 10 # # * Query Cache Configuration # query_cache_limit = 1M query_cache_size = 32M # skip-federated slow-query-log skip-name-resolve Update: I followed the instructions as per http://dev.mysql.com/doc/refman/5.1/en/forcing-innodb-recovery.html and set innodb_force_recovery = 4 and the logs are showing a different error but the behavior is still the same: 101210 19:14:15 mysqld_safe mysqld restarted 101210 19:14:19 InnoDB: Started; log sequence number 456 143528628 InnoDB: !!! innodb_force_recovery is set to 4 !!! 101210 19:14:19 [Warning] 'user' entry 'root@PSDB102' ignored in --skip-name-resolve mode. 101210 19:14:19 [Warning] Neither --relay-log nor --relay-log-index were used; so replication may break when this MySQL server acts as a slave and has his hostname changed!! Please use '--relay-log=mysqld-relay-bin' to avoid this problem. 101210 19:14:19 [Note] Event Scheduler: Loaded 0 events 101210 19:14:19 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.31-1ubuntu2-log' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu) 101210 19:14:32 InnoDB: error: space object of table mydb/__twitter_friend, InnoDB: space id 1602 did not exist in memory. Retrying an open. 101210 19:14:32 InnoDB: error: space object of table mydb/access_request, InnoDB: space id 1318 did not exist in memory. Retrying an open. 101210 19:14:32 InnoDB: error: space object of table mydb/activity, InnoDB: space id 1595 did not exist in memory. Retrying an open. 101210 19:14:32 - mysqld got signal 11 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=1 max_threads=600 threads_connected=1 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x1753c070 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f7a0b5800d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f7cbc350080] /usr/sbin/mysqld(ha_innobase::innobase_get_index(unsigned int)+0x46) [0x77c516] /usr/sbin/mysqld(ha_innobase::innobase_initialize_autoinc()+0x40) [0x77c640] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x3f3) [0x781f23] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f7cbc3483ba] /lib/libc.so.6(clone+0x6d) [0x7f7cbae91fcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x1754d690 = thd->thread_id=1 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash.

  Read the article

• SSL timeout on some sites, across all browsers, on Mac OS X Snow Leopard

  - by dansays

  For the past several weeks, I've been receiving "Error 7 (net::ERR_TIMED_OUT): The operation timed out" when I attempt to connect to either Twitter or Paypal via SSL. I get this specific error in Google Chrome, but the same problem occurs in both Safari and Firefox. Other sites work fine, and other computers on my network can access these two sites. I have no firewall settings that would prevent me from accessing these sites over port 443. I notice that both Twitter and Paypal both have "Verisign Class 3 Extended Validation SSL CA" certificates. It is unclear whether this is related to the problem. In an effort to troubleshoot, I attempted to open the test sites referenced on Verisign's root certificate support page, which worked fine. Just to be sure, I downloaded and installed the root package file and installed all included Verisign certificates. No joy. I feel like I've hit a dead end. Any ideas? Update the first: I also cannot connect to FedEx.com, who also has a Verisign Class 3 Extended Validation cert. Update the second: Aaaaaaand it fixed itself. I did nothing. Or, I did something that worked, but in a delayed fashion. Frustrating, but a win is a win. I'll take it.

  Read the article

• Authority Information Access local path being ignored

  - by Kevin

  I have a CA set up in Server 2008 R2, and generally it is working, but I can't control the local path/filename it writes its own certificate to for the Authority Information Access publishing. Here's a screen shot of the dialog I'm trying to set this on: From these settings I would expect to get the file: C:\Windows\system32\CertSrv\CertEnroll\DAMNIT.crt But instead I get: C:\Windows\system32\CertSrv\CertEnroll\SERVER.domain.com_My Issuing Authority(1).crt Of course, the actual change shown wouldn't be very useful, but it's illustrative; no matter what path/filename I use, it always lands up in the same place and with the same name. I actually wanted to change the name from <ServerDNSName>_<CaName><CertificateName>.crt to <CaName><CertificateName>.crt, since the latter corresponds to the HTTP URL whereas the former does not. Admittedly, I haven't set up many CAs so perhaps I'm just deluded as to what this dialog is supposed to be setting, but if so this is notoriously bad UI design. (Incidentally, I have a couple other complaints with the same dialog.) What's going on here and is there some way to get the filename pattern I want?

  Read the article

• PHP script not automatically updating when moved to another server

  - by user32007

  A friend built a ranking system on his site and I am trying to host in on mine via WordPress and Go Daddy. It updates for him but when I load it to my site, it works for 6 hours, but as soon as the reload is supposed to occur, it errors and I get a 500 timeout error. His page is at: jeremynoeljohnson .com/yakezieclub My page is currently at http://sweatingthebigstuff.com/yakezieclub but when you ?reload=1 it will give the error. Any idea why this might be happening? Any settings that I might need to change? Here is the top of the index.php file. I'm not sure which part of any of it is messing up. I literally uploaded the same code as him. Here's the reload part: $cachefile = "rankings.html"; $daycachefile = "rankings_history.xml"; $cachetime = (60 * 60) * 6; // every 6 hours, the cache refreshes $daycachetime = (60 * 60) * 24; // every 24 hours, the history will be written to // - or whenever the page is requested after 24 hours has passed $writenewdata = false; if (!empty($_GET['reload'])) { if ($_GET['reload']== 1) { $cachetime = 1; } } if (!empty($_GET['reloadhistory'])) { if ($_GET['reloadhistory'] == 1) { $daycachetime = 1; $cachetime = 1; } } if (file_exists($daycachefile) && (time() - $daycachetime < filemtime($daycachefile))) { // Do nothing } else { $writenewdata = true; $cachetime = 1; } // Serve from the cache if it is younger than $cachetime if (file_exists($cachefile) && (time() - $cachetime < filemtime($cachefile))) { include($cachefile); echo "<!-- Cached ".date('jS F Y H:i', filemtime($cachefile))." -->"; exit; } ob_start(); // start the output buffer ?>

  Read the article

• Overriding HOMEDRIVE and HOMEPATH as a Windows 7 user

  - by MikeC

  My employer has an Active Directory group policy which sets my Windows 7 laptop HOMEDRIVE to "M:" (a mapped network drive) and my HOMEPATH to "\". Since I have read-only permissions for the root of that shared drive, I cannot create files or directories in my windows home directory. My attempts to work with the IT department have been unsuccessful. Is there a way for me to globally change these envars at boot or login time? I need for all applications to use alternate values (such as "C:" and "\Users\myname"). I have some installed utilities (like gvim and others) that store preference files in the user's home directory. IMPORTANT: Changing these envars under "System Properties Environment Variables" does not work. I have tried setting these as both User and System Variables (including a reboot). TypingSET HOMEin a DOS window clearly shows that my settings are ignored. Also, using "Start in" in a Windows shortcut will also not solve this, as I need things like Explorer context menu items (like "Edit with Vim") to operate correctly. I do have admin rights on this company laptop, but I am not a Win7 guru. Back in the day, a boot script would have solved this in a minute. Is it even possible today? Thanks.

  Read the article

• Windows Server 2012 Hyper-V very slow

  - by Matt Taylor

  I have been running several Hyper-V VMs on Windows Server 2008 R2 for the past couple of years and enjoying perfectly adequate performance for my testing/development/r&d environments. I'm a software developer so my hardware knowledge is basic however I built the rig using: •Gigabyte GA-X58A-UD3R Intel X58 (Socket 1366) DDR3 Motherboard •Intel Core i7 960 3.20GHz (Bloomfield) (Socket LGA1366) •24GB triple channel RAM The host OS is running on an OCZ SSD and all the VMs are running on a 2TB Marvell SATA3 RAID 0 array consisting of 2 Western Digital Caviar Black 7,200rpm drives. I have tested the speed of the 2TB drive and appear to be getting less than 3Mbs but it can adequately run a 4 VM farm including a DC, (SQL) database and IIS application servers. I recently upgraded the SSD on which the host runs to a 256GB OCZ Vertex 4 and took the opportunity to upgrade to Windows Server 2012 and installed the Hyper-V role. I tried importing one of my existing Windows Server 2008 R2 VMs (and converted it to .vhdx) plus I have tried creating a brand new Windows Server 2008 R2 VM but both are running extremely slowly and I can see nothing obvious using the host and guest Task Manager/Resource Monitor tools. In both cases the VM has 8GB RAM (fixed), 4 CPUs, fixed size HD (not expanding) and is using an external virtual network running on a separate NIC to the host. I have upgraded the BIOS to the latest available version and checked the virtualization settings. I have run out of "obvious" (to a developer) things to check/configure and my next option will be to re-install the host OS but before I do I would very much appreciate any advice from any experts out there. Thanks

  Read the article

< Previous Page | 484 485 486 487 488 489 490 491 492 493 494 495  | Next Page >