Search Results

Search found 1712 results on 69 pages for 'respond to'.

Page 49/69 | < Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >

  • Why is my server performance degrading to the point of stopping, periodically?

    - by Pascal Aschwanden
    So, once in a while, I see in firebug that a request takes over 15 or even 60 seconds to respond and sometimes never. Here is what I've ruled out: It's not the CPU, cuz every time I check the Server load its less then 6 for all 3 numbers It's not the memory, because thats fairly low too, less the 50% It's not the I/O anymore, because I've seen the graphs that Joyent sent back to me when I requested them, and they show less then 3MB of I/O (mostly all read). It's not the SQL performance - I've profiled every last SQL command that runs, and they're all (99.9% of them anyway) running in less then 30ms, most run in less then 5ms. Oh and I've been profiling all the script execution times, and even the when the problem occurs, the script always manages to finish in 50ms or less (that's 1 / 20th of a second ). Now, I do run alot of ajax calls. 1 every 2 seconds per user and I have 300 DAU+. But, even if all 300 are playing simultaneously, thats still only 150 calls per second max. The only other thing I can think of is that one of my neighbors is funky. The problem is highly intermittent. 99% of the time it works perfectly and there's excellent performance. but 99%+ is not good enough. Eventually the performance gets so bad I have to restart the server, at which point everything is fine again. I've done this about 4 times now. Any ideas? Note: this is on joyent, vps, intro package 256mb of ram with bursting. here are the mysql dump info: Traffic ø per hour Received 18 MiB 29 MiB Sent 134 MiB 221 MiB Total 151 MiB 251 MiB Connections ø per hour % max. concurrent connections 5 --- --- Failed attempts 0 0.00 0.00% Aborted 0 0.00 0.00% Total 9,418 15.59 k 100.00%

    Read the article

  • How can I use my cell phone to establish a dial-up networking connection?

    - by gWiz
    I am using Windows 7 and have a BlackBerry with T-Mobile (U.S.). I have paired the phone with my computer over Bluetooth, which automatically creates a serial port for it. I am able to open the port in PuTTY and successfully issue AT commands to the modem, including dialing. However, while using Windows to create and establish a Dial-Up Networking connection, I get an error dialog stating "Error 678. The remote computer did not respond." In my testing, I also tried setting up a connection to dial a number connected to a phone. When attempting to connect over this connection, the phone does ring but the very moment I answer the call, my computer displays the above error dialog. What must be done to successfully establish such a PPP connection? Some special AT initialization string perhaps? To clarify, I'm not referring to the well-described and popular technique known as "tethering," in which the remote host of the data link is the mobile service provider. I am interested specifically in establishing direct data links with remote hosts other than my mobile service provider. Think old-school landline connection to your friend's computer or BBS. Edit 1 As grawity pointed out in comments, the missing piece of the puzzle is the actual modulator that is compatible with v-series protocols, which I expected to be built into the cellphone. So far the best only software alternative I could find is this experimental project. Edit 2 Found this forum discussion today. The participants state that there is no old-school modem in the BlackBerry. Edit 3 When I place a call in PuTTY with ATD, immediately after the call is answered (and the callee is initiating the handshake) the cellphone returns OK. This is not the expected behavior for establishing a data connection. The phone should reciprocate the handshake, and upon success return CONNECT. (Alternatively it should return BUSY or NO CARRIER, but never simply OK.) Windows DUN must be interpreting this as the "Error 678" I was seeing.

    Read the article

  • DNS Zone file and virtual host question (repost because my question got moved and now I can't comment on the original for some reason)

    - by Jake
    Sorry this is a repost, the original question got moved to here form stack overflow and for some reason I can't comment or respond to answers on that one anymore. Hi all, I'm trying to set up a virtual host for redmine.SITENAME.com. I've edited the httpd.conf file and now I'm trying to edit my DNS settings. However, I'm not sure exactly what to do. Here's an snippet of what's already in the named.conf file (the file was made by someone else who is unreachable): zone "SITENAME.com" { type master; file "SITENAME.com"; allow-transfer { ip.address.here.00; common-allow-transfer; }; }; I figure if I want to get redmine.SITENAME.com working, I need to copy that entry and just replace SITENAME.com with redmine.SITENAME.com but will that work? I was under the impression I needed a .db file but I don't see any reference to one in the current named.conf file. I also don't see any .db files or files named SITENAME in named.conf's directory. Any ideas where these illusive pre-existing db files could be?

    Read the article

  • Help trying to figure out why IIS7 is crashing / locking up / denying connections

    - by Pure.Krome
    Hi folks, I've got a pretty busy website that is running on a single web front end machine, on W2K8 + IIS7. Every now and then - eg. maybe monday at 3am or something, then a few days later .. some early morning time .. then nothing for 2 weeks ... etc - the website fails to respond to any client connections. ie. no one can connect to the website. I can remote desktop to the machine, etc no probs. I restart the app pool (the website is running in intergrated mode), still nothing. I try and get a crash dump of the process (it's around 600 mb maybe even more) ... that fails after about a min of trying (and i have plenty of HD space). The only way to fix this issue, is to manually stop the www service and then start it again. The stopping takes a while (a minute?) while starting is nearly instant. I'm at a loss to figure out what part of my code is causing this. At first, I thought it might be a stack overflow because of some error that might be going to the error page, which in turn errors .. rinse repeat boom. But i've had a look at the error page and it feels ok. So, I'm hoping someone might be able to help and say how I can correctly get a proper dump of the IIS process so i can then do some more autopsy on it. I would email Tess Ferrandez (the goddess of crash debuging) but I thought I'd try here before I spam her. Can anyone have any suggestions to how I can figure out how to start to debug this issue?

    Read the article

  • What does Firefox do when "scanning for viruses" after download?

    - by Joey
    Never mind the fact that Firefox is a browser and not a AV tool, but what exactly does it do after a download? Even on systems that have an up-to-date AV this generates a pause of several seconds after download (where I can't open the file from within the DL manager) and I have no idea what FF might be trying there. I know I can turn it off (using FF only at work anyway) but I'm wondering. I can think of some things here what it might be: FF itself is a AV scanner and it loads signatures in the background and whatnot. Sounds highly unlikely and shouldn't need tens of seconds for 20 KiB files. FF tries to talk with the installed AV to munch the file. Sounds unneeded, given that most AV programs feature real-time protection anyway and therefore will have caught a virus already and also because FF does that on systems without AV installed too. FF uploads the file to some online virus checker. Unlikely and stupid. FF instructs some online virus checker to download the file and check it. Unlikely and would be a nice target for DoSing that service. FF generates a hash of the file and sends that somewhere (presumably Google) to check for. They then respond with either "Whoa, that hash is totally a virus" or "Nope, that MD5 doesn't look very virus-y to me". I'm running out of better ideas. Anyone have a clue?

    Read the article

  • Dual hard drive Windows 7 system, modified the registry to get programs to install on second drive, now IE doesn't work

    - by paul
    I have a dual hard drive Windows 7 system, Windows is installed on an SSD (C:) and I modified the registry to try to force programs to install on second HDD drive (another letter). The registry edits are pretty simple, just a few keys in HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion to change the drive letter. For the most part the system is very fast and works great, but IE doesn't work anymore. With IE10, it opens for a flash with a white window then closes. I tried installed IE11 which opens a white window for a few seconds, doesn't respond, then crashes. I've tried all the solutions I could find. This includes resetting the IE settings, "uninstalling" and re-installing IE, which is just turning it on and off in "Turn Windows Features on or off", copying the Program Files\Internet Explorer files onto both/either drives, changing the registry keys back to use C:, lots of rebooting, and safe mode. Nothing has worked. I don't see errors in the event viewer, but I might not know what to look for. Any ideas on how to get IE running? I don't need IE for daily browsing, I just need it for cross-browser testing on sites I build and on the rare occasion a page only works in IE. I don't really want to use a virtual machine, but would be ok with something standalone like tredosoft's, but I'm not aware of something like that for current versions of IE.

    Read the article

  • Redis connection issue

    - by mre
    We are currently experiencing a lot of Redis errors with the message Unable to connect: read error on connection, trying next server We run Redis on FreeBSD using PHP Redis and we have a hard time reproducing the error on Ubuntu so this might be a hint. There's a long-running issue on that topic on github. Basically we get a socket from the operating system with a call to connect(host, port, timeout) in phpredis, but when we do a select(db_index) afterwards, we get an exception. Could there be an issue with persistance? I assume that connect does nothing in the background and select tries to access the connection, which is actually closed. We don't run into a timeout. We tried tuning TIME_WAIT without success. Any other ideas on where the problem might come from? What is the best way to track the issue down? dtrace maybe? Update We are currently looking into our BGSAVE settings. Interestingly it takes half a second and more to create a fork for the process which regularly writes the data to disk (persistence) and maybe redis can't respond to connect() requests during that timespan.

    Read the article

  • How can I use an own asp page as 404 error page on a Windows 7 pro IIS 7.5 local installation

    - by Edelcom
    Running Windows 7 Pro Running local IIS 7.5 ( for web development purposes ) Edited hosts file to be able to use http://www.sitestepper.dev Site build in subfolder of the inetpub/wwwroot/staplijst Site can be viewed using http://www.sitestepper.dev/staplijst/whatever-page.htm I have an http://www.sitestepper.dev/p.asp page I would like to call when an unknown page is requested. This technique works fine on the deployed version of this web site ( deployed on an Windows 2003 server running IIS 7 - not sure about the 7 but it is the version deployed with Windows 2003 server ). I tried ( in the Edit Custom Error Dialog ) : Execute a URL on this site: with value /staplijst/p.asp and Respond with a 302 redirect: with value http://www.sitestepper.dev/staplijst/p.asp I tried this in the properties of the 'Default Web Site' , and I tried this at the staplijst level. Even tried it with values without the /staplijst. I restarted the default web site after each change. And even stopped/started the Web service. But nothing seems to work, I keep getting the 'Server Error In Application "DEFAULT WEB SITE"' , HTTP Error 404.0 error. What am I missing here - probably something obvious, but I don't see it ? Thanks in advance

    Read the article

  • Nginx: Loopback connection via PHP's getimage size crashes server (Magento's CMS)

    - by Alex
    We were able to trace down a problem that is crashing our NGINX server running Magento until the following point: Background info: Magento Backend has a CMS function with a WYSIWYG editor. This editor loads some pictures via a controller in magento (cms/directive). When we set the NGINX error_log level to info, we get the following lines (line break inserted for better readability): 2012/10/22 18:05:40 [info] 14105#0: *1 client closed prematurely connection, so upstream connection is closed too while sending request to upstream, client: XXXXXXXXX, server: test.local, request: "GET index.php/admin/cms_wysiwyg/directive/___directive/BASEENCODEDIMAGEURL,,/ HTTP/1.1", upstream: "fastcgi://127.0.0.1:9024", host: "test.local" When checking the code in the debugger, the following call does never return (in ´Varien_Image_Adapter_Abstract::getMimeType()` # $this->_fileName is http://test.local/skin/adminhtml/base/default/images/demo-image-not-existing.gif` # $_SERVER['REQUEST_URI'] = http://test.local/admin/cms_wysiwyg/directive/___directive/BASEENCODEDIMAGEURL list($this->_imageSrcWidth, $this->_imageSrcHeight, $this->_fileType, ) = getimagesize($this->_fileName); The filename requests is an URL to the same server which is requesting the script a link to a static .gif that is not existing. Sample URL: http://test.local/skin/adminhtml/base/default/images/demo-image-not-existing.gif When the above line executed, any subsequent request to the NGNIX server does not respond any more. After waiting for around 10 minutes, the NGINX server starts answering requests again. I tried to reproduce the error with a simple test script that only calls getimagesize() with the given URL - but this not crash. It simple leads to an exception saying that the URL could not be loaded (which is fine as the URL is wrong)

    Read the article

  • Windows Server 2008 IIS Random disconnect

    - by d123
    I am having a bit of a quirk with my IIS server. I'm running my IIS with 2 sets of IPs configured, one in the 192 range and the other in 172 range. I then have multiple apps which will talk to this server for information. Server has no AV or firewalls configured. I noticed that my apps when talking to the server on the 172 range, at random intervals, the server would just not respond. My apps would then disconnect and just try again, and every thing would be fine. This doesn't happen on the 192 range. So what I did is on a Linux box I did a watch command and to wget a file every half second on the 172 and 192 IPs. I noticed the same issue, every once in awhile wget on the 172 range would not get through, but there is no issues at all on 192. Thus I went around to Wireshark and did a dump. This is the last 3 packets, no other packets were received. 7010 100.871877 200.100.30.7 172.0.0.1 TCP 59619 http [ACK] Seq=140 Ack=85242 Win=64128 Len=0 TSV=1072818795 TSER=1660246133 7011 100.872238 200.100.30.7 172.0.0.1 TCP 59619 http [FIN, ACK] Seq=140 Ack=85242 Win=64128 Len=0 TSV=1072818796 TSER=1660246133 7013 100.873081 200.100.30.7 172.0.0.1 TCP 59619 http [ACK] Seq=141 Ack=85243 Win=64128 Len=0 TSV=1072818796 TSER=1660246133 So this is my issue, there is a random disconnect every once in awhile. The server doesn't receive the next SYN packet. HELP?

    Read the article

  • postfix revived and delivered have the same values (?)

    - by thinkingbig
    I have configured my first server (Debian with ISPConfig). Generally i want to send bulk e-mails to our users, i configure postfix and turn on postfix... but... After 1 hour of sending emails i have logs like this: Grand Totals messages 21886 received 21883 delivered 0 forwarded 0 deferred 234 bounced 0 rejected (0%) 0 reject warnings 0 held 0 discarded (0%) 30805k bytes received 31280k bytes delivered 3 senders 3 sending hosts/domains 12588 recipients 3 recipient hosts/domains Per-Hour Traffic Summary time received delivered deferred bounced rejected -------------------------------------------------------------------- 0000-0100 0 0 0 0 0 0100-0200 0 0 0 0 0 0200-0300 0 0 0 0 0 0300-0400 0 0 0 0 0 0400-0500 0 0 0 0 0 0500-0600 0 0 0 0 0 0600-0700 0 0 0 0 0 0700-0800 0 0 0 0 0 0800-0900 0 0 0 0 0 0900-1000 0 0 0 0 0 1000-1100 0 0 0 0 0 1100-1200 0 0 0 0 0 1200-1300 0 0 0 0 0 1300-1400 0 0 0 0 0 1400-1500 0 0 0 0 0 1500-1600 15311 15306 0 168 0 1600-1700 6575 6577 0 66 0 1700-1800 0 0 0 0 0 1800-1900 0 0 0 0 0 1900-2000 0 0 0 0 0 2000-2100 0 0 0 0 0 2100-2200 0 0 0 0 0 2200-2300 0 0 0 0 0 2300-2400 0 0 0 0 0 Host/Domain Summary: Message Delivery sent cnt bytes defers avg dly max dly host/domain 21521 30353k 0 3.4 m 15.5 m wp.pl 355 919k 0 54.9 s 13.0 m mysenderdomainexample.pl 7 8477 0 1.7 s 1.9 s prokonto.pl Host/Domain Summary: Messages Received msg cnt bytes host/domain 21879 30786k mysenderdomainexample.pl 5 16196 mx4.wp.pl 1 3200 mx3.wp.pl Senders by message count 21783 [email protected] 96 [email protected] 6 from=< **So, my question is: 1) Why i have recived and delivered have the same values (approx)? 2) How can I check if an email has been delivered? 3) How to change default "root" and "www-data" user (FROM / RETURN PATH) to another? I have changed this in script, but postfix ignore scripting values and send every mail from root (we have .php send cron's in /etc/crontab) 4) WHY APPROX 100 % MAILS RECIVED HAS BEEN ADRESED TO MY SENDER HOST? Host/Domain Summary: Messages Received Waiting for respond, Regards TB**

    Read the article

  • How to set a static route for an external IP address

    - by HorusKol
    Further to my earlier question about bridging different subnets - I now need to route requests for one particular IP address differently to all other traffic. I have the following routing in my iptables on our router: # Allow established connections, and those !not! coming from the public interface # eth0 = public interface # eth1 = private interface #1 (10.1.1.0/24) # eth2 = private interface #2 (129.2.2.0/25) iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -m state --state NEW ! -i eth0 -j ACCEPT iptables -A FORWARD -i eth0 -o eth1 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i eth0 -o eth2 -m state --state ESTABLISHED,RELATED -j ACCEPT # Allow outgoing connections from the private interfaces iptables -A FORWARD -i eth1 -o eth0 -j ACCEPT iptables -A FORWARD -i eth2 -o eth0 -j ACCEPT # Allow the two private connections to talk to each other iptables -A FORWARD -i eth1 -o eth2 -j ACCEPT iptables -A FORWARD -i eth2 -o eth1 -j ACCEPT # Masquerade (NAT) iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE # Don't forward any other traffic from the public to the private iptables -A FORWARD -i eth0 -o eth1 -j REJECT iptables -A FORWARD -i eth0 -o eth2 -j REJECT This configuration means that users will be forwarded through a modem/router with a public address - this is all well and good for most purposes, and in the main it doesn't matter that all computers are hidden behind the one public IP. However, some users need to be able to access a proxy at 192.111.222.111:8080 - and the proxy needs to identify this traffic as coming through a gateway at 129.2.2.126 - it won't respond otherwise. I tried adding a static route on our local gateway with: route add -host 192.111.222.111 gw 129.2.2.126 dev eth2 I can successfully ping 192.111.222.111 from the router. When I trace the route, it lists the 129.2.2.126 gateway, but I just get * on each of the following hops (I think this makes sense since this is just a web-proxy and requires authentication). When I try to ping this address from a host on the 129.2.2.0/25 network it fails. Should I do this in the iptables chain instead? How would I configure this routing?

    Read the article

  • exim4 seem to stop listening

    - by trakos
    Hey, I have a strange problem with my exim4 configuration. I have a dedicated server running debian for quite a long time now, but I'm not really using it actively recently, so everything just worked due to lack of changes ;) However, recently, my exim4 smtp stopped answering on port 25. It does not respond through localhost, as well - even though it's set to listen on any interface available. Some things I've checked: ks:/home/trakos/Maildir/new# netstat -ap | grep exim tcp 0 0 *:smtp : LISTEN 12521/exim4 ks:/home/trakos/Maildir/new# exiwhat 12521 daemon: -q30s, listening for SMTP on port 25 (IPv4) ks:/home/trakos/Maildir/new# cat /var/log/exim4/rejectlog ks:/home/trakos/Maildir/new# cat /var/log/exim4/paniclog The queue is set for 30s only because I was running it in a non-daemon mode to see any output. Strangely enough, no suspicious output is given, netstat even shows it is listening on port 25, but still trying to telnet to it times out. The only things that may have changed recently are: I've got second IP for my server I remember that few days ago my spamassasin crashed, and I've started it up again So yeah, I'm really clueless about this one now :P I mean, I don't even know what could be failing here. Could someone give me some ideas what should I check next? PS: it has uptime of 442 days, so I haven't really tried rebooting it yet ^^

    Read the article

  • Does having TRIM enabled affect other hard drives on a computer (and how do you know when Windows is using it)?

    - by Breakthrough
    I recently purchased a solid state drive (an OCZ Vertex 2 (80 GB)) to use as my primary operating system partition. I also have three other SATA hard drives of assorted sizes. I successfully installed Windows 7 Professional onto the SSD (works awesome, great response time and transfer rate), and used the other three HDDs for data storage. I was browsing through the Bible of OCZ SSDs, and noticed the following in Section 60-76 - Tweaks and TRIM: Q. How do I know if TRIM is enabled on my OCZ SSD? A. In Windows 7, go to start/run/cmd), type the following: fsutil.exe behaviour query DisableDeleteNotify It should respond back with: DisableDeleteNotify=0 if TRIM support is ready and active. If it's not, then type: fsutil.exe behavior set DisableDeleteNotify 0 After a bit of searching on Google, I found similar results elsewhere (set DisableDeleteNotify to 0, which makes sense since for TRIM to work, the solid-state drive needs to be notified when deletes occur (for the garbage collector) unlike a normal hard drive). When I run the query on fsutil, I get the following result: DisableDeleteNotify = 48 Following the instructions I found, I set this to 0 instead of 48. However, I am beginning to wonder. Is this all the proof I really need that the OS is using TRIM? Also, since this applies globally for the computer, is TRIM data being sent to the other hard drives connected to the computer? And if so, would this cause any degradation in disk performance?

    Read the article

  • Acer Aspire Touchscreen Not Responding

    - by Jerry
    I have an Acer Aspire z3101 all-in-one Touch screen running Windows 7 Home Premium. I am unable to get the screen to respond to my touch. I have checked the system and all drivers are ok according to comp. Using the settings to setup the pen and touch and to calibrate does not work. My touch brings no response at all. I had reinstalled the applications - Windows Touch Pack and Acer Touch Portal which didn't help. Today I done a complete reinstall returning comp back to factory settings and still there is no response. At first I thought that perhaps a driver or file was missing but now doubt that due to the reinstall not helping. Have you any idea what could be causing this problem? I am now at the stage of pulling my hair out and haven't had too much help from Acer. I have had the computer for just over a year now and so it is no longer under guarantee and this has me very worried due to my being unemployed. Any help is much appreciated. Thank you.

    Read the article

  • OpenSSL force client to use specific protocol

    - by Ex Umbris
    When subversion attempts to connect to an https URL, the underlying protocol library (openssl) attempts to start the secure protocol negotiation at the most basic level, plain SSL. Unfortunately, I have to connect to a server that requires SSL3 or TLS1, and refuses to respond to SSL or SSL2. I’ve done some troubleshooting using s_client and confirmed that if I let s_client start with the default protocol the server never responds to the CLIENT HELLO: $ openssl s_client -connect server.domain.com:443 CONNECTED(00000003) write:errno=104 --- no peer certificate available --- No client certificate CA names sent --- SSL handshake has read 0 bytes and written 320 bytes --- New, (NONE), Cipher is (NONE) Secure Renegotiation IS NOT supported Compression: NONE Expansion: NONE --- Watching this in Wireshark I see: Client Server -------syn----------> <------ack----------- ---CLIENT HELLO-----> <------ack----------- [60 second pause] <------rst----------- If I tell s_client to use ssl2 the server immediately closes the connection. Only ssl3 and tls1 work. Is there any way to configure openssl to skip SSL and SSL2, and start the negotiation with TLS or SSL3? I've found the OpenSSL config file, but that seems to control only certificate generation.

    Read the article

  • Computer won't start up. Stuck on Lenovo splash screen. Help Diagnose

    - by Ace Legend
    I have some (I'm not sure exactly what model) Lenovo 21" IdeaCentre. Honestly, the computer works off and on. I have had problems with it not being able to shutdown, which I fixed. The fan seems to be constantly running, a few other problems as well. Anyway, nobody was using it when all of a sudden it switched to a blue screen. I was in the kitchen, but when I got over to the computer I read the message. It said something about bad drivers, but that is all I saw and then it restarted. However, when it got to the Lenovo Splash screen, nothing happened. I waited there for over 10 minutes, but still nothing. I tried to turn of the computer, but the only way to do it was to pull out the power cable. I then removed all USB devices and tried again. Still nothing. It also won't respond to keyboard input when I try to use enter to interrupt normal startup. My guess is some piece of hardware is damaged inside the machine. However, I have no idea what piece it is. Does anybody have any idea what could be wrong with it? Thanks.

    Read the article

  • Allow outgoing connections for DNS

    - by Jimmy
    I'm new to IPtables, but I am trying to setup a secure server to host a website and allow SSH. This is what I have so far: #!/bin/sh i=/sbin/iptables # Flush all rules $i -F $i -X # Setup default filter policy $i -P INPUT DROP $i -P OUTPUT DROP $i -P FORWARD DROP # Respond to ping requests $i -A INPUT -p icmp --icmp-type any -j ACCEPT # Force SYN checks $i -A INPUT -p tcp ! --syn -m state --state NEW -j DROP # Drop all fragments $i -A INPUT -f -j DROP # Drop XMAS packets $i -A INPUT -p tcp --tcp-flags ALL ALL -j DROP # Drop NULL packets $i -A INPUT -p tcp --tcp-flags ALL NONE -j DROP # Stateful inspection $i -A INPUT -m state --state NEW -p tcp --dport 22 -j ACCEPT # Allow established connections $i -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allow unlimited traffic on loopback $i -A INPUT -i lo -j ACCEPT $i -A OUTPUT -o lo -j ACCEPT # Open nginx $i -A INPUT -p tcp --dport 443 -j ACCEPT $i -A INPUT -p tcp --dport 80 -j ACCEPT # Open SSH $i -A INPUT -p tcp --dport 22 -j ACCEPT However I've locked down my outgoing connections and it means I can't resolve any DNS. How do I allow that? Also, any other feedback is appreciated. James

    Read the article

  • ASA access lists and Egress Filtering

    - by Nate
    Hello. I'm trying to learn how to use a cisco ASA firewall, and I don't really know what I'm doing. I'm trying to set up some egress filtering, with the goal of allowing only the minimal amount of traffic out of the network, even if it originated from within the inside interface. In other words, I'm trying to set up dmz_in and inside_in ACLs as if the inside interface is not too trustworthy. I haven't fully grasped all the concepts yet, so I have a few issues. Assume that we're working with three interfaces: inside, outside, and DMZ. Let's say I have a server (X.Y.Z.1) that has to respond to PING, HTTP, SSH, FTP, MySQL, and SMTP. My ACL looks something like this: access-list outside_in extended permit icmp any host X.Y.Z.1 echo-reply access-list outside_in extended permit tcp any host X.Y.Z.1 eq www access-list outside_in extended permit tcp any host X.Y.Z.1 eq ssh access-list outside_in extended permit tcp any host X.Y.Z.1 eq ftp access-list outside_in extended permit tcp any host X.Y.Z.1 eq ftp-data established access-list outside_in extended permit tcp any host X.Y.Z.1 eq 3306 access-list outside_in extended permit tcp any host X.Y.Z.1 eq smtp and I apply it like this: access-group outside_in in interface outside My question is, what can I do for egress filtering? I want to only allow the minimal amount of traffic out. Do I just "reverse" the rules (i.e. the smtp rule becomes access-list inside_out extended permit tcp host X.Y.Z.1 any eq smtp ) and call it a day, or can I further cull my options? What can I safely block? Furthermore, when doing egress filtering, is it enough to apply "inverted" rules to the outside interface, or should I also look into making dmz_in and inside_in acls? I've heard the term "egress filtering" thrown around a lot, but I don't really know what I'm doing. Any pointers towards good resources and reading would also be helpful, most of the ones I've found presume that I know a lot more than I do.

    Read the article

  • Window 7 image in vmware will allow network connection out but not http

    - by Ormis
    I am currently trying to create a set of images to deploy on my network, but I've run in to a snag. When I create my own Windows 7 image I can successfully use NAT for connecting to the network but whenever I try to access a webpage I get nothing. To be more specific, All firewalls/iptables are disabled on my host machine, my virtual machine, and my network. I can do lookups and all addresses respond correctly (i'm even using Google's DNS). On the host OS i have full connectivity. On the virtual machine I can ping any device I want and all addresses resolve correctly. Within a browser I cannot reach any page via hostname or IP. I feel almost like port 80 is being blocked but i can't find any reason this would be the case. If anyone has had this occur before, I would love some insight to the problem. I initially asked this on stackoverflow and now my eyes are now opened up to superuser. Thank you for any help you can provide.

    Read the article

  • Laptop Synaptics Touchpad No Longer Functional After Windows 7 Upgrade

    - by Chance
    I have a Toshiba laptop, with an integral Synaptics (PS/2 port) touch pad, that I bought pre-installed with 32-bit Windows Vista. After doing a clean install of 32-bit Windows 7, I can no longer get the touch pad to respond. The function (FN) keys on the laptop still operate correctly, but they no longer display on screen when used. I have no way of knowing if the function key to enable / disable the touch pad is working correctly, although the function keys for dim / brighten display, as well as others, work fine. I have removed the device from the device manager and allowed it to reinstall with no success. I have removed the previous drivers and updated them with the current 32-bit Win7 compatible versions from Synaptics website, with no success. The Synaptics icon displays in the taskbar, and the touch pad is available in the Device Manager, both of which say the device is installed and working correctly. I have checked to make sure that the touch pad is enabled in the Synaptics menu, and have tried toggling enabled / disabled with no success. If anyone has any suggestions, or knows where I can find a solution, I would be very appreciative.

    Read the article

  • Looking for a powershell script that can pull a file from a set of PC's and FTP

    - by DangeRuss
    I'm looking to write a script (preferably powershell) that will essentially copy a file from a bunch of PC's and FTP it to a server. So the structure of the environment is that we have a file on multiple PC's (around 50 or so) that need to placed on a server. Sometimes one of the PC's may be turned off so the script would first need to ensure the PC is up and running (maybe a ping result), then it would need to go into a directory on that PC, pull a file off of it, rename the file, place into a source directory, then remove the file. Naming convention doesn't matter, but date/time stamp would be easiest. Ideally, it would be best to first move all the files to a source directory to save on FTP bandwidth, but since the files will be named the same, the files must be renamed during the move process. Move not copy because the directory needs to be empty so the file can be re-created the next day. So once moved to the source directory, now all the files need to be FTP'd to a server for processing. After all of this, we need to know which PC's on the list did not respond so we can manually retrieve the file so the script should output a file (txt is fine) that will show which PC's were offline. Everything is one domain and script will be run from an server with admin creds. Thank you!

    Read the article

  • Exchange 2013 really slow outside of localhost

    - by ItsJustJP
    We've got a 12 core xeon, 24GB of ram 2012 server. We've recently migrated from exchange 2010 (which was on another server) to exchange 2013 which resides on our new 12 core server. Accessing the OWA on the exchange server is fine; it's very quick and responsive however accessing it via any other computer connect to the domain via a 1 gpbs connection and it'll take 10-15 seconds to load. Also running slow is public calenders that people in my place need to access, again taking 10-15 seconds to access and can sometimes cause outlook to not respond. Further to that we have phones that connect via the internet (of course) to the exchange so people can get work emails when they are out of the office. Guess what, this is also running slow. I've have search for many solutions and have tried changing outlook authentication methods but there is no change in speed. The old exchange 2010 server no longer exists but there was no problem before the migration. Has anyone got any suggestions? Thanks :) Must also mention that server 2012 that exchange 2013 is installed on is also the DC. Update: It would appear that any connection via https is slow. It took more than 15 mins for an outlook client to download 50MB of emails (outlook anywhere).

    Read the article

  • How can I tell System Restore in WIndows 7 recovery console to use my recovered backup drive's restore point data?

    - by Rich Shealer
    My Windows 7 desktop PC failed to boot. It would get to a grayish screen with a mouse and would only respond to the power button. After much examination I found that the problem was not a failed drive as running CHKDSK from the Recovery Console on my main drives passed without any errors. I had been installing various Java version in the days before the failure so I decided to use a restore point to roll backwards. I have an external SATA drive controller with two 2 TB drives mirrored using the Windows mirroring function. My system has been backing up to this drive regularly. The problem is I accidently broke the mirror when testing to see if this drive system might have been causing my boot issue. Connecting it to another machine showed two dynamic drives that were invalid. In the end I reformatted one as an NTFS basic disc and used recovery software on the other to copy all of the files to the reformatted drive. I had to copy the restore points into the new drive's System Volume Information folder by granting rights to that user. I moved the drive back to the original machine and rebooted. I can see my new drive, it even uses the same drive letter as it did in normal mode. Running System Restore it lists a new Automatic Restore point created while sitting at the RC along with all of my backups. Selecting the backup I want (or any other) I get a dialog. The backup drive could not be found. System Restore is looking for restore points on your backup. Make sure the backup drive is on and connected to this computer and then click OK. What do I need to do to allow system restore to see the restore points?

    Read the article

  • Why won't sql server express 2008 service restart after I enable TCP/IP Protocol?

    - by John
    Whenever I enable TCP/IP connections on my SQL Server Express 2008 database server running on Windows XP SP3, I cannot restart the service, it simply states "The request failed or did respond in a timely fashion". Any suggestions of what I may have configured incorrectly? [update] Here is the applicable part of the Error Log: MSSQL$SQLEXPRESS Server failed to list on 'any' 3060. Error: 0x2747. To proceed, notify you system administrator. MSSQL$SQLEXPRESS TDSSNIClient initialization failed with error 0x2747, status code 0xa. Reason: Unable to initialize the TCP/IP listener. An operation on a socket could not be performed because the system lacked sufficient buffer space or because a queue was full. MSSQL$SQLEXPRESS TDSSNIClient initialization failed with error 0x2747, status code 0x1. Reason: Initialization failed with an infrastructure error. Check for previous errors. An operation on a socket could not be performed because the system lacked sufficient buffer space or because a queue was full. MSSQL$SQLEXPRESS Could not start the network library because of an internal error in the network library. To determine the cause, review the errors immediately preceding this one in the error log. MSSQL$SQLEXPRESS SQL Server could not spawn FRunCM thread. Check the SQL Server error log and the Windows event logs for information about possible related problems.

    Read the article

< Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >