Search Results

Search found 15323 results on 613 pages for 'db2 connect'.

Page 518/613 | < Previous Page | 514 515 516 517 518 519 520 521 522 523 524 525  | Next Page >

• Can a USB/IDE/SATA adapter be flaky?

  - by Ward

  I use USB/IDE/SATA converters a lot and on the two that I have now, I sometimes get errors copying files to drives. It only happens when I'm copying big files to the drive (big can mean as little as 100MB, I think it happens more often with bigger files - 300MB or more), and basically the copy will fail and I'll get one or more error messages about "Delayed write failed." But if I disconnect the drive and re-connect it, I'll usually be able to continue. (The file that was being copied will be corrupt, but otherwise the drive is fine.) I just noticed a new type of flakiness: the data transfer rate can vary widely. I copied one set of files (5x300MB files) and it took 10+minutes, then I copied another set (approx. the same sizes) and it took less than a minute. I haven't done systematic testing, the other things I'm doing on my laptop at the same time might have some impact, and I haven't cross-checked the two adapters I have and the 3 hard drives I'm working with to see if there's a pattern. I'm more wondering if anyone else has seen anything like this.

  Read the article

• Getting old bluetooth headset out of standby on Windows 7

  - by luagh45

  I think this is the problem, and if not, I'm open to suggestions. I have an old Jabra BT200 that I used to use on my phone. When a phone call was coming in it would beep using its own noises (meaning the phone never rang inside the headset) and then I could push the 'answer/hang up' button and sound and mic would start working. I have now paired it with Windows 7, and it looks good. Under the playback menu I have 'Bluetooth Hands free Audio / Jabra BT200 (Mono Audio) / Ready', and under the recording menu I have 'Bluetooth Audio Input Device / Jabra BT200 (Mono Audio) / Ready'. However when I try to test the speakers Windows sends a sound, but I never hear it, and when I talk in the mic, Windows never hears me. If I right click either the Bluetooth mic or speakers there's an option to 'Connect', but it's grayed out and I cannot click it. As the final piece of knowledge I have, my headset blinks once every 3 seconds when it's in standby and I can't get that to change. If everything was working it should blink once every second at which point I think all of my problems would be fixed. Hence my issue: I can't seem to get my headset out of standby. On my headset I've tried sending it test noises and then pressing the 'Answer' button, but still nothing. The headset beeps when I press it, so it works, it just doesn't ever come out of standby. Is there maybe some way to trick my headset into thinking it's getting a phone call from my computer?

  Read the article

• Can't see more than the first few lines in an SSH connection

  - by hello

  I need some help for SSH buffer size. I have a vista machine at home and i have installed "Free SSHD" on it. I also have Dynamic DNS setup to access some of my home lab equipment which are connected to this vista machine. From my work machine which is an XP machine I connect to my home machine using Putty. Everything up to this point is working fine without any problem. The issue is I can't see more lines than the first few lines of the output. I press the space bar to get more output off the screen and the output scrolls up and it gets lost as the more output gets displayed on the screen. The Putty client i am using on my work machine has been setup with enough buffer size but the output still only displays few lines and as it moves up, the buffer gets empty automatically. I have searched the entire web and haven’t found any proper solution any where. Can someone please help here? Thanks.

  Read the article

• Can Haproxy deny a request by IP if its stick-table is full?

  - by bantic

  In my haproxy configs I'm setting a stick-table of size 5 that stores every incoming IP address (for 1 minute), and it is set as nopurge so new entries won't get stored in the table. What I'd like to have happen is that they would get denied, but that isn't happening. The stick-table line is: stick-table type ip size 5 expire 1m nopurge store gpc0 And the whole configs are: global maxconn 30000 ulimit-n 65536 log 127.0.0.1 local0 log 127.0.0.1 local1 debug stats socket /var/run/haproxy.stat mode 600 level operator defaults mode http timeout connect 5000ms timeout client 50000ms timeout server 50000ms backend fragile_backend tcp-request content track-sc2 src stick-table type ip size 5 expire 1m nopurge store gpc0 server fragile_backend1 A.B.C.D:80 frontend http_proxy bind *:80 mode http option forwardfor default_backend fragile_backend I have confirmed (connecting to haproxy's stats using socat readline /var/run/haproxy.stat) that the stick-table fills up with 5 IP addresses, but then every request after that from a new IP just goes straight through -- it isn't added to the stick-table, nothing is removed from the stick-table, and the request is not denied. What I'd like to do is deny the request if the stick-table is full. Is this possible? I'm using haproxy 1.5.

  Read the article

• Nginx server 301 Moved permanently

  - by user145714

  When I did a curl -v http://site-wordpress.com:81 I received this result: About to connect() to site-wordpress.com port 81 (#0) Trying ip... connected Connected to site-wordpress.com (ip) port 81 (#0) GET / HTTP/1.1 User-Agent: curl/7.19.7 (x86_64-unknown-linux-gnu) libcurl/7.19.7 NSS/3.12.6.2 zlib/1.2.3 libidn/1.18 libssh2/1.2.2 Host: site-wordpress.com:81 Accept: / < HTTP/1.1 301 Moved Permanently < Server: nginx/1.2.4 < Date: Fri, 16 Nov 2012 16:28:19 GMT < Content-Type: text/html; charset=UTF-8 < Transfer-Encoding: chunked < Connection: keep-alive < X-Pingback: The URL above/xmlrpc.php < Location: The URL above Seems like this line in my fastcgi_params is causing grief. fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; If I remove this line , I get HTTP/1.1 200 OK but I get a blank page. This is my config: server { listen 81; server_name site-wordpress.com; root /var/www/html/site; access_log /var/log/nginx/access.log; error_log /var/log/nginx/error.log; index index.php; if (!-e $request_filename){ rewrite ^(.*)$ /index.php break; } location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; # port where FastCGI processes were spawned fastcgi_index index.php; include /etc/nginx/fastcgi_params; include /etc/nginx/mime.types; } location ~ \.css { add_header Content-Type text/css; } location ~ \.js { add_header Content-Type application/x-javascript; } } This config works with ip and port 80. But now I need to use a domain name and port 81, which doesn't work. Could someone please help. Thanks.

  Read the article

• RabbitMQ Management console not working

  - by rrejc

  I have started with RabbitMQ. I have a (windows) machine on which I installed two RabbitMQ nodes as a service - I have choose the nodename, port and service name for each of them. The services are running normally (i see that they are listening in a netstat-a). I have also installed management plugin with "rabbitmq-plugins enable rabbitmq_management" and restarted both services. But the plugin isn't running - I dont see it listening in a netstat and I can't connect to the management console via browser. Any idea what could be wrong? Is there any log to see what is goind on? Updated: when I do rabbitmq-plugins list i get: c:\RabbitMq\sbin>rabbitmq-plugins list [e] amqp_client 3.0.1 [ ] cowboy 0.5.0-rmq3.0.1-git4b93c2d [ ] eldap 3.0.1-gite309de4 [e] mochiweb 2.3.1-rmq3.0.1-gitd541e9a [ ] rabbitmq_auth_backend_ldap 3.0.1 [ ] rabbitmq_auth_mechanism_ssl 3.0.1 [ ] rabbitmq_consistent_hash_exchange 3.0.1 [ ] rabbitmq_federation 3.0.1 [ ] rabbitmq_federation_management 3.0.1 [ ] rabbitmq_jsonrpc 3.0.1 [ ] rabbitmq_jsonrpc_channel 3.0.1 [ ] rabbitmq_jsonrpc_channel_examples 3.0.1 [E] rabbitmq_management 3.0.1 [e] rabbitmq_management_agent 3.0.1 [ ] rabbitmq_management_visualiser 3.0.1 [e] rabbitmq_mochiweb 3.0.1 [ ] rabbitmq_mqtt 3.0.1 [ ] rabbitmq_old_federation 3.0.1 [ ] rabbitmq_shovel 3.0.1 [ ] rabbitmq_shovel_management 3.0.1 [ ] rabbitmq_stomp 3.0.1 [ ] rabbitmq_tracing 3.0.1 [ ] rabbitmq_web_stomp 3.0.1 [ ] rabbitmq_web_stomp_examples 3.0.1 [ ] rfc4627_jsonrpc 3.0.1-git7ab174b [ ] sockjs 0.3.3-rmq3.0.1-git92d4ba4 [e] webmachine 1.9.1-rmq3.0.1-git52e62bc

  Read the article

• How do I activate the F_LINE input in a transplanted HP chassis?

  - by admin

  I have an HP Pavilion Media Center PC chassis, vintage 2003 or so and I replaced the motherboard in it with a newer (vintage 2009) HP motherboard, M2N68-LA (Narra 5). I have scoured the internet trying to find pinouts for the motherboard to no avail. My question concerns the front panel audio, specifically Line In. The old chassis was built for AC97 but the new mobo is build for the newer HD audio standard. I figured out by comparison & experimentally how to connect the Mic & Headphone jacks to the HD audio header of the mobo by adding a manual switch to set the SENSE lines. Now all works fine for Mic & headphone. The old chassis also has a front panel Line In jack that the newer HP chassis does not have. However, the new mobo has a 4 pin white connector labeled F_LINE that I believe is a line input. Under Windows 7 I see the two Line Inputs in the mixer but I can't get one of them to become active. The 4 pin F_LINE connector uses the two middle pins for ground, and presumably the other two for left and right audio inputs. There are no pins for sensing on that connector. Can anyone tell me how to use that F_LINE input for the front panel, or how to activate it?

  Read the article

• Using Truecrypt to secure mySQL database, any pitfalls?

  - by Saul

  The objective is to secure my database data from server theft, i.e. the server is at a business office location with normal premises lock and burglar alarm, but because the data is personal healthcare data I want to ensure that if the server was stolen the data would be unavailable as encrypted. I'm exploring installing mySQL on a mounted Truecrypt encrypted volume. It all works fine, and when I power off, or just cruelly pull the plug the encrypted drive disappears. This seems a load easier than encrypting data to the database, and I understand that if there is a security hole in the web app , or a user gets physical access to a plugged in server the data is compromised, but as a sanity check , is there any good reason not to do this? @James I'm thinking in a theft scenario, its not going to be powered down nicely and so is likely to crash any DB transactions running. But then if someone steals the server I'm going to need to rely on my off site backup anyway. @tomjedrz, its kind of all sensitive, individual personal and address details linked to medical referrals/records. Would be as bad in our field as losing credit card data, but means that almost everything in the database would need encryption... so figured better to run the whole DB in an encrypted partition. If encrypt data in the tables there's got to be a key somewhere on the server I'm presuming, which seems more of a risk if the box walks. At the moment the app is configured to drop a dump of data (weekly full and then deltas only hourly using rdiff) into a directory also on the Truecrypt disk. I have an off site box running WS_FTP Pro scheduled to connect by FTPs and synch down the backup, again into a Truecrypt mounted partition.

  Read the article

• Nginx Server Block Not Working? - Already running other vhosts just this one not working

  - by daveaspinall

  Im running a Debian 6 LEMP server with multiple virtual hosts and everything has been fine for 5 or so sites. But I've just tried adding another but for some reason it's just not working. By not working I mean in Chrome I get the "Oops! Google Chrome could not connect to subdomain.domain.net" error. I've changed the domain for security to subdomain.example.com and the IP is masked. Hosts file (I have multiple sub domains): xxx.xxx.xx.xxx *.example.com *.example Server Block: server { listen 80; server_name subdomain.example.com; access_log /srv/www/subdomain.example.com/logs/access.log; error_log /srv/www/subdomain.example.com/logs/error.log; root /srv/www/subdomain.example.com/public_html; location / { index index.html index.htm index.php; } location ~ \.php$ { include fastcgi_params; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; } } I've created the system link to the file in the /etc/nginx/sites-enabled/ directory and restarted/reloaded nginx. DNS seems fine: # ping -c 2 subdomain PING subdomain.example.com (xxx.xxx.xx.xxx) 56(84) bytes of data. 64 bytes from www.example.com (xxx.xxx.xx.xxx): icmp_req=1 ttl=64 time=0.035 ms 64 bytes from www.example.com (xxx.xxx.xx.xxx): icmp_req=2 ttl=64 time=0.048 ms Checking the file with cURL works: # curl http://subdomain.example.com HTML - OK Emptied browser cache but still no dice. Anything I'm missing? Like I mentioned, I have a few sites running fine on the server currently so php-fpm etc etc are working. Any help would be much appreciated! Cheers, Dave

  Read the article

• How can I pair two bluetooth dongles together?

  - by techaddict

  I want to hack a device which connects via USB, and plug a bluetooth USB dongle to the end of the USB cable (using a female to female adapter), and then connect to that device from another USB bluetooth dongle connected to my computer. How can I do this? It is straightforward? I don't want to spend $30 before I know how to do this. Also I think another concern is that the USB cable is providing power to the device. So I think that means I would also have to hack it for power. I have created this diagram in Photoshop to illustrate my intent: (NOTE: it won't be a USB mouse, as that would be pointless because there are already wireless mice in existence. The mouse is displayed for illustrative purposes) Don't tell me "it won't work". Because I KNOW it WILL work. Think for example, PS3 controller. That works, and in fact I was able to get it working with my laptop, over bluetooth. I just want to know HOW to make it work.

  Read the article

• iptables : how to allow incoming ftp traffic?

  - by logansama

  Hi, Still fighting my way through the jungle that is called iptables. I have managed to allow FTP access outside of our LAN: both these would work. NOTE: eth0 is the LAN interface and eth1 is the WAN interface. iptables -t filter -A FORWARD -i eth0 -p tcp --dport 20:21 -j ACCEPT or iptables -A FORWARD -i eth0 -o eth1 -p tcp --sport 20:21 --dport 1024:65535 -j ACCEPT But when i connect to a external FTP server i manage to log in and all is fine until it wishes to List the directory content. Then nothing happens as the data is blocked, due to the fact that i do not have a rule set up to allow it! (my last rule on the FORWARD chain is to block all traffic) I have tried a gazillion rules (many of which i did not understand) to try and allow the FTP traffic back through my server. One such rule for example was: iptables -A FORWARD -i eth1 -o eth0 -p tcp --sport 20:21 --dport 1024:65535 -j ACCEPT But i cannot get the List to work. It just times out after a while. Would anyone perhaps know how to build a rule which would allow FTP to List / allow such traffic back? Or have a link to sources i could work through? Thank you,

  Read the article

• Cisco 851 (IOS) router: FastEthernet 4 (WAN) got the shutdown flag.

  - by cjavapro

  At a customer location there was a Cisco 851 router (which uses IOS). The PCs on location were all of a sudden unable to connect. We came on site and found that FastEthernet 4 (the WAN port) was "administratively down". We ran these commands to resolve it config t interface fa4 no shutdown exit exit write Now the mystery is how the shutdown flag got there in the first place? The router was on battery backup... but during the outage it was power cycled by the customer. It is possible that there was a short outage by the ISP and that the power cycle caused the shutdown flag to come up. There may have been a hack or an attack pattern that caused the shutdown flag to come up. There may have been a hack or an attack pattern that the router to become unavailable and then caused the shutdown flag to be added on startup. Question: Does anybody have any clues? or at least remember that they had a shutdown flag come up on their WAN port also?

  Read the article

• Can ZFS ACL's be used over NFSv3 on host without /etc/group?

  - by Sandra

  Question at the bottom. Background My server setup is shown below, where I have an LDAP host which have a group called group1 that contains user1, user2. The NAS is FreeBSD 8.3 with ZFS with one zpool and a volume. serv1 gets /etc/passwd and /etc/group from the LDAP host. serv2 gets /etc/passwd from the LDAP host and /etc/group is local and read only. Hence it doesn't not know anything about which groups the LDAP have. Both servers connect to the NAS with NFS 3. What I would like to achieve I would like to be able to create/modify groups in LDAP to allow/deny users read/write access to NFS 3 shared directories on the NAS. Example: group1 should have read/write to /zfs/vol1/project1 and nothing more. Question The problem is that serv2 doesn't have a LDAP controlled /etc/group file. So the only way I can think of to solve this is to use ZFS permissions with inheritance, but I can't figure out how and what the permissions I shall set. Does someone know if this can be solved at all, and if so, any suggestions? +----------------------+ | LDAP | | group1: user1, user2 | +----------------------+ | | | |ldap |ldap |ldap | v | | +-----------+ | | | NAS | | | | /zfs/vol1 | | | +-----------+ | | ^ ^ | | |nfs3 |nfs3| v | | v +-----------------------+ +----------------------------+ | serv1 | | serv2 | | /etc/passwd from LDAP | | /etc/passwd from LDAP | | /etc/group from LDAP | | /etc/group local/read only | +-----------------------+ +----------------------------+

  Read the article

• SSH connection times out unless I tunnel in from a different server-

  - by rm-vanda

  OK, so this just started last week - Whenever we try to connect to our server via ssh (we use sftp, as well) - The connection times out. However, when you ssh to any other server and then ssh into the machine - it works flawlessly. Now, the mindblowing thing is that sometimes the ssh connection will succeed. Moments ago, I tried it from another machine, and then my own, and it worked - only to time out the next go around. Last week, simply restarting the ssh daemon worked, but this week, no such luck. I even went in and changed: /etc/hosts.allow ALL : ALL and /etc/hosts.deny is blank. The firewall config hasn't changed - but I even disabled the firewall to see if that would work - It did, for a moment - before cutting off, again. (ufw is set to "ALLOW" not "LIMIT") When I try SSH'ing in from my phone -- it works, fine -- So, it seems the problem is with our ISP/router/gateway - However, I see no log in the router/gateway that says its blocking our connections - And that wouldn't explain why we can SSH into any other server -- except for this one - from our network --- I truly appreciate any insight that anyone may have on this matter -

  Read the article

• System With Two Network Adapters

  - by Synetech inc.

  Hi, My system has a NIC (Marvell Yukon) built-into the motherboard, but I also have a D-Link (RealTek) card. I figure that using the D-Link and disabling the Marvell makes the most sense, though I'm wondering if maybe the built-in one has better throughput (not that my Internet connection is so fast). Also, I'm wondering about the merits of using both at the same time. My router has four ports and I have experimented with enabling and plugging both NICs into the router. I was able to connect to the Internet, but the pattern of usage seemed irregular (which adapter was chosen for the transfer and any given point). I also considered bridging the two, but am having difficulty in finding out what exactly creating network bridge does in the context of the Windows Network Connections window. I am familiar with the concept of connecting networks, so it seems to me that birding two connections on the same segment is pointless at best (and can cause problems like loops?) Does anyone have any tips on what to do if a system has more than one NIC and any clarification on the bridge option? Thanks a lot.

  Read the article

• What differences are there between "home" switches and "professional" switches?

  - by pjreddie

  Our radio station uses a PtP wireless system to stream our radio and TV signals from our studio up a hill to our transmitter. We have been having problems with warbly sound and drop outs that come from some point in this system. An engineer that occasionally visits the station thinks it could be the switches we use on each side of the PtP wireless system to connect the PtP devices to the encoders and decoders and wants us to get two of these switches: http://www.amazon.com/Netgear-JGS516-ProSafe-16-Port-Ethernet/dp/B0002CWPOK/ref=dp_return_1 The encoder/decoder setup only streams 8Mbps total so it seems like the switches we have should not be stressed out, unless they are causing sufficient latency to degrade the performance of the encoder/decoder. At each end of the connection we only have 4 connections, is there any reason we couldn't get a cheaper, "home" quality switch like this: http://www.amazon.com/D-Link-DGS-1005G-5-Port-Gigabit-Desktop/dp/tech-data/B003X7TRWE/ref=de_a_smtd Is there a significant difference that we would notice in terms of latency between these two switches? How much does the quality of the switch actually matter in this scenario? Any help is appreciated, feel free to ask questions if anything needs clarification. Thanks

  Read the article

• Is it possible to trace someone using Google during an online exam?

  - by George

  I happen to be a professor at a reputed college. I want to design an online exam for over 1000 students via around 50 computers right after the vacation ends. Now the problem is that I have heard that many students use Google on a different tab to find answers when no invigilator is around. I want to know if there is a way to backtrace it after the exams via some kind of history or any other possible way. In our university there is a standard system. I am not good with computers but I will try to explain. Each computer uses mozilla to connect to a server centrally located via an IP. The students open it and enter a unique ID and password to start the exams. Many questions are jumbled and different groups of students give exam in a different time slot. Is there any way to trace it since I want to set an example for students so they won't cheat and give exams in an honest way. Additional details: Since the number of computers are less than the number of students, more than 10 students are going to use a single computer on a single day over a period of 10 hours. After this, if I check the history (and let's say someone even forgot to delete the history and I see it), will I able to figure out who among the 10 has done it? Moreover, is it even practical and feasible?

  Read the article

• Network Sharing Issues

  - by Mark Kramer

  I have two computers I want to have on a network share together (so the laptop can print through the desktop's printer). These are both connected to the same router. (One wired and one wireless) And they both have the same workgroup name. However, when I type "net view" in the command prompt, the only computer that shows up is the computer I type the command into. How do I get these computers to be shared with each other? Update: The tower is running Windows XP, the Laptop is running Windows 7. I have disabled the Firewall on both until I get this set up. Update 2: Typing the command net view on my desktop is acting very strangely. Noe sometimes it only shows itself on the list of computers, sometimes it shows itself and the laptop and sometimes it doesn't work at all and displays system error 6118. I typed net view into the command prompt on the Windows 7 laptop and both computers showed up, so I went to connect to the desktop from the laptop and it said the dekptop could not be found, even though it is showing up int he list of shared computers. Here are supporting pictures (these are coming from the laptop)

  Read the article

• How can one keep secure regular backups of his desktop on a remote server through aDSL? [on hold]

  - by Antonis Christofides

  I'm a system administrator and I use rsnapshot to backup some servers, duplicity for some others. Both work fine, each one with advantages and disadvantages. Despite that, I am at a loss on how to backup my own private files. I'd use duplicity to automatically backup my files to a remote server; but the problem is that once in a while I must do a full backup. My emails and important files are 9G, and I expect this to increase. Uploading through aDSL at 1Mbit would be 20 hours. Too much. rsnapshot doesn't require periodic full backups (only the first time), but it must be running on the remote server and have a means to connect to my computer; if the server is compromised (or simply if the NSA decides to use it), my own machine is also compromised. Not good. The only solution I've come up with is use encfs, use unison to synchronize the files to a remote server, and use duplicity or rsnapshot on the remote server to backup these files. In that case, the question is whether I can sync the files on many computers; is it possible for encfs to be used with the same key on many computers? I also think that if I append one character to the unencrypted file, its encrypted encfs counterpart might change a lot, so that incrementals with duplicity would be less efficient—but not a big deal. Maybe also, when I need to restore a file, finding the correct file to restore could be a pain, because of filename encryption. I wonder whether there is any other possibility that I've overlooked. Maybe I'm asking too much for my personal use, and I should settle with an external disk?

  Read the article

• Use both OpenVPN & eth0 together

  - by shadyabhi

  I connect to a VPN using openVPN. Now, after the connection is established, all my traffic goes through tun0. My LAN gateway is 10.100.98.4... So, for apps to use my direct internet connnection I did sudo route add default gw 10.100.98.4 But, I cant use tun0 now. I know this because curl --interface tun0 google.com doesnt give me anything.. How do I go about using both connections simultaneously. How can I achieve that? ROUTING TABLES:- Without VPN running:- Destination Gateway Genmask Flags Metric Ref Use Iface 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 default 10.100.98.4 0.0.0.0 UG 0 0 0 eth0 With VPN:- Destination Gateway Genmask Flags Metric Ref Use Iface 10.10.0.1 10.10.54.230 255.255.255.255 UGH 0 0 0 tun0 10.10.54.230 * 255.255.255.255 UH 0 0 0 tun0 free-vpn.torvpn 10.100.98.4 255.255.255.255 UGH 0 0 0 eth0 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 default 10.10.54.230 0.0.0.0 UG 0 0 0 tun0 After the route command- Destination Gateway Genmask Flags Metric Ref Use Iface 10.10.0.1 10.10.54.230 255.255.255.255 UGH 0 0 0 tun0 10.10.54.230 * 255.255.255.255 UH 0 0 0 tun0 free-vpn.torvpn 10.100.98.4 255.255.255.255 UGH 0 0 0 eth0 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 default 10.100.98.4 0.0.0.0 UG 0 0 0 eth0 default 10.10.54.230 0.0.0.0 UG 0 0 0 tun0

  Read the article

• Export files to remote server using TortoiseSVN

  - by Matt

  I'm using TortoiseSVN to keep revisions of my code. When I commit changes, I take note of what files have changed and upload them to my server using FTP. Here's my workflow: Edit files on local computer (eg. files in C:\Users\Me\web) Commit changes to local repository using rightclick- TortoiseSVN- SVN Commit. Take the files, open FileZilla (FTP client) and upload the files to a remote server. I was wondering if there was a way in which I could omit step 3 from my workflow. Basically I would like the changed files to be automatically uploaded to the remote server when I commit a version to the repository. Information about my computer environment: Windows 7 Ultimate x64 with TortoiseSVN x64 Notepad++ text editor Files edited are PHP, CSS, JS, HTML, etc. Server is running Linux with PHP 5.2 and MySQL. FileZilla is used to upload files. I can connect to the server via SSH if that is needed. Thank you in advance.

  Read the article

• Large scale file replication with an option to "unsubscribe" from a replicated file on a given machine

  - by Alexander Gladysh

  I have a 100+ GB files per day incoming on one machine. (File size is arbitrary and can be adjusted as needed.) I have several other machines that do some work on these files. I need to reliably deliver each incoming file to the worker machines. A worker machine should be able to free its HDD from a file once it is done working with it. It is preferable that a file would be uploaded to the worker only once and then processed in place, and then deleted, without copying somewhere else — to minimize already high HDD load. (Worker itself requires quite a bit of bandwidth.) Please advise a solution that is not based on Java. None of existing replication solutions that I've seen can do the "free HDD from the file once processed" stuff — but maybe I'm missing something... A preferable solution should work with files (from the POV of our business logic code), not require the business logic to connect to some queue or other. (Internally the solution may use whatever technology it needs to — except Java.)

  Read the article

• Trouble setting up incoming VPN in Microsoft SBS 2008 through a Cisco ASA 5505 appliance

  - by Nils

  I have replaced an aging firewall (custom setup using Linux) with a Cisco ASA 5505 appliance for our network. It's a very simple setup with around 10 workstations and a single Small Business Server 2008. Setting up incoming ports for SMTP, HTTPS, remote desktop etc. to the SBS went fine - they are working like they should. However, I have not succeeded in allowing incoming VPN connections. The clients trying to connect (running Windows 7) are stuck with the "Verifying username and password..." dialog before getting an error message 30 seconds later. We have a single external, static IP, so I cannot set up the VPN connection on another IP address. I have forwarded TCP port 1723 the same way as I did for SMTP and the others, by adding a static NAT route translating traffic from the SBS server on port 1723 to the outside interface. In addition, I set up an access rule allowing all GRE packets (src any, dst any). I have figured that I must somehow forward incoming GRE packets to the SBS server, but this is where I am stuck. I am using ADSM to configure the 5505 (not console). Any help is very much appreciated!

  Read the article

• Is it possible to record a screen-video from a VNC server?

  - by nikie

  I have a computer that's running VNC server. I would like to record a video of what's going on on this computer, if possible without installing additional software on that computer. Is there a program that can connect to the VNC server port and instead of displaying the screen save it to an (e.g. AVI) video file? Background: One of our customers sometimes has problems with the software he bought from us when he's performing a complex procedure. To help him, we offered that someone (a service technician or programmer) watches what he's doing during that procedure to find out if he's doing something wrong or if there's a bug in the software. Currently, this is done live via VNC. That has a few disadvantages: The service technician has to be in the office at the time. As the customers are in different time zones, that can be in the middle of the night. If the service technician forgets something or doesn't notice something, it's lost. There's no way to see what happened again. Only a single computer can be watched by one service technician at a time. I know I could install normal screen-grab software on the computer, but we're talking about an embedded system with limited RAM, CPU, HDD space, so installing something new is not an easy decision. And VNC is already there. I could of course open a VNC client on some office PC and capture that PC's screen, but I can only record one remote computer that way. I often have to watch up to 8 screens in parallel. (And I don't think that screen-grabbing VNC would improve image quality, either.)

  Read the article

• Connecting a Wifi router to receivers with a cable instead of antenna?

  - by 31eee384

  This is a very strange question--I'd go so far as to say it's a stupid question. I'm being told that it is possible to, to describe it briefly, use a cable to connect an access point and a receiver directly to one another. This means that I would unscrew the access point's antenna, and attach one end of a cable to the port. Then, on the wireless receiver, I would also unscrew the antenna and plug in the other side of the cable. I'm being told the connection would work after this, just as a normal Wifi connection would. Bonus mini-question: if this works, would it still work if a splitter were attached to the access point and multiple receivers plugged in to the network? What would happen if I do this? Based on my surprisingly deficient knowledge of radio transmission, I don't think it would work. I would like some help knowing why it won't (or will) though, if possible. This is a somewhat hypothetical question--I realize that Ethernet does this exact job very handily, and I could just throw in a switch instead of the splitter. I simply feel that I should understand this scenario. Thanks for any help you can offer.

  Read the article

< Previous Page | 514 515 516 517 518 519 520 521 522 523 524 525  | Next Page >