Search Results

Search found 31360 results on 1255 pages for 'virtual address space'.

Page 540/1255 | < Previous Page | 536 537 538 539 540 541 542 543 544 545 546 547  | Next Page >

• Debian, 2 NICs load-balancing or agregating with one same gateway

  - by pouney

  Hi, I have one server, with double NICs connected to one switch with the same gateway. Behind the switch we have internet. |Debian| - eth0 - switch - internet - eth1 - same I don't understand how to load-balancing between eth0 and eth1. The inbound/outbound traffic always use eth1. This is the config: # The primary network interface allow-hotplug eth0 auto eth0 iface eth0 inet static address 192.168.248.82 netmask 255.255.255.240 network 192.168.248.80 broadcast 192.168.248.95 gateway 192.168.248.81 allow-hotplug eth1 auto eth1 iface eth1 inet static address 192.168.248.83 netmask 255.255.255.240 network 192.168.248.80 broadcast 192.168.248.95 gateway 192.168.248.81 Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.248.80 0.0.0.0 255.255.255.240 U 0 0 0 eth1 192.168.248.80 0.0.0.0 255.255.255.240 U 0 0 0 eth0 0.0.0.0 192.168.248.81 0.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.248.81 0.0.0.0 UG 0 0 0 eth0 Ips aren't real, it's just for the example. Anybody have an idea on correct routing to use eth0 on 192.168.248.82 and eth1 on 192.168.248.83 ? I have many example for multiple gateway but here it's the same. Thanks all. Regards

  Read the article

• Why do HTTP loopback connections not work on my subdomains?

  - by memeLab

  I have a shared hosting account at Jumba running Linux kernel 2.6.9-103.ELsmp (don't know if that helps) with cpanel 1.0 (RC1). I am using the WordPress plugin Backup Buddy, which requires HTTP loopback connections to monitor / complete backups. This works fine on memelab.com.au, but doesn't work at any subdomain (e.g.: staging.memelab.com.au). Is it possible to setup an A record or some such to remedy this? I'm aware of a workaround, (setting WP_ALTERNATE_CRON) but I find this unsatisfactory due to the messy URLs. BackupBuddy:_Frequent_Support_Issues#HTTP_Loopback_Connections_Disabled Here is the reply from my host: …as main domain have it's own separate DNS entry it have localhost entry which helps for looback connections where as subdomains don't have separate DNS zone, so it is not possible to create looback connections for it. I have cpanel access to the 'advanced zone editor' - is there anything tricky I can do there? maybe 127.0.0.2? (I remember reading that there were at least 8 available local IPs available on (some) Linuxes.) All the A records point to the server IP, with the exception of localhost.memelab.com.au which points to 127.0.0.1. I've just tried entering a new A record: localhost.itours.memelab.com.au pointing to 127.0.0.2. I still get the warning in Backup Buddy that loopback is not active, and Cpanel won't let me enter 127.0.0.1 (guess it doesn't work like that!) nslookup itours.memelab.com.au Server: 203.88.112.33 Address: 203.88.112.33#53 Non-authoritative answer: Name: itours.memelab.com.au Address: 117.55.224.177

  Read the article

• Can I sysprep a bootable VHD without using any virtualization technology?

  - by senf

  I booted from a VHD on my laptop and hoped to sysprep this image, but it didn't let me do it. I got a fatal error during the process. I used the following command: sysprep /generalize /shutdown. My question is it possible at all to sysprep a VHD without any HyperV or virtual PC technology?

  Read the article

• Can't authorize a server for Amazon RDS

  - by Parris

  We are attempting to slowly migrate a website over to AWS among other things. We decided the first thing to move was the database. We have some dedicated server with a different hosting provider. We only have one IP. I am having trouble authorizing the ip so that the old server can connect to RDS. It simply hangs for a while while using the mysql cli, then responds: ERROR 2003 (HY000): Can't connect to MySQL server on 'db.address.us-east-1.rds.amazonaws.com' (110) It did work on my laptop though. I am not quite sure what is wrong. I have a feeling I don't quite understand CIDR/IP. I simply took the ip address and tacked on /32 at the end. Then I gleaned some information that it also has to do with subnet mask? ifconfig reports: 255.255.255.0 I found a calculator and the IP changed a bit and had /24 at the end. That still didn't work. One other note... perhaps i dont know enough about the differences between OS. The hosting provider is using centOS, while our development machines are all ubuntu. Any insight would be extremely helpful! THANKS :)

  Read the article

• How to know disk quota on network share in windows?

  - by myforwik

  I connect to a share on a windows server and I have a quota of unknown size. All the tools I have seen are reporting the disk size/disk free space, not the quota size for myself. The only way I can figure out my quotas is to keep writing junk until I reach the quota. There must be a better way than this? My PC is windows XP and the servers are mainly 2003server.

  Read the article

• Default IPv6 route on debian squeeze does not come up after boot

  - by Georg Bretschneider

  I have a problem with my default IPv6 route not coming up after boot on a Debian Squeeze system. This is my config (/etc/network/interfaces): # Loopback device: auto lo iface lo inet loopback iface lo inet6 loopback # device: br0 auto br0 iface br0 inet static bridge_ports eth0 bridge_fd 0 address 88.198.62.xx broadcast 88.198.62.63 netmask 255.255.255.224 gateway 88.198.62.33 up route add -net 88.198.62.32 netmask 255.255.255.224 gw 88.198.62.33 br0 iface br0 inet6 static address 2a01:4f8:131:10x::2 netmask 64 gateway 2a01:4f8:131:100::1 up route -A inet6 add 2a01:4f8:131:100::1/59 dev br0 My inet comes up alright, but I have to exec the route command manually after boot to make IPv6 work. Otherwise I can't even reach my gateway. This is the output of ip -6 route show after boot: 2a01:4f8:131:10x::/64 dev br0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 unreachable fe80::/64 dev lo proto kernel metric 256 error -101 mtu 16436 advmss 16376 hoplimit 4294967295 fe80::/64 dev br0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 I already tried it with: up ip -6 route add 2a01:4f8:131:100::1 dev br0 up ip -6 route add default via 2a01:4f8:131:100::1 dev br0 in /etc/network/interfaces, but with the same results. If I execute those commands manually on my shell, everything starts working nicely. And yes, I tried with post-up instead of up, too. Only other changes I made was to activate ip forwarding for IPv6, because I want to run some LXC containers on that system.

  Read the article

• Connect to Nonencrypted Wireless Network Using Ubuntu Commands

  - by Tim

  I failed to connect to an open i.e. nonencrypted wireless network using Ubuntu command lines. Here is what I did: $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo /sbin/ifconfig wlan0 up $ sudo iwconfig wlan0 essid "Cavalier High-Speed 866-4-CAVTEL" $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 10812 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 21 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6 No DHCPOFFERS received. Trying recorded lease 192.168.1.67 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms Trying recorded lease 192.168.1.45 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms No working leases in persistent database - sleeping. $ sudo /sbin/iwconfig wlan0 wlan0 IEEE 802.11bg Mode:Managed Frequency:2.422 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I was wondering what the problem is and how I can do it right? Thanks and regards!

  Read the article

• Malicious content on server - next steps advice [closed]

  - by Under435

  Possible Duplicate: My server's been hacked EMERGENCY I just got an e-mail from my hosting company that they got a report of malicious content being hosted on my vps. I was unaware of this and started looking into it. I discovered a file called /var/www/mysite.com/osc.htm. Soon after I discovered some weird php files wp-includes.php and ndlist.php both recognized as being PHP/WebShell.A.1 virus. I removed all these files but I'm unsure of what to do next. Can anyone help me analyze the output below of sudo netstat -A inet -p -e and give advice on what's best to do next. Thanks very much in advance Proto Recv-Q Send-Q Local Address Foreign Address State User Inode PID/Program name tcp 0 0 localhost.localdo:mysql localhost.localdo:37495 TIME_WAIT root 0 - tcp 0 1 mysite.com:50524 xnacreators.net:smtp SYN_SENT Debian-exim 69746 25848/exim4 tcp 0 0 mysite.com:www tha165.thehealtha:37065 TIME_WAIT root 0 - tcp 0 0 localhost.localdo:37494 localhost.localdo:mysql TIME_WAIT root 0 - udp 0 0 mysite.com:59447 merlin.ensma.fr:ntp ESTABLISHED ntpd 3769 2522/ntpd udp 0 0 mysite.com:36432 beast.syus.org:ntp ESTABLISHED ntpd 4357 2523/ntpd udp 0 0 mysite.com:48212 formularfetischiste:ntp ESTABLISHED ntpd 3768 2522/ntpd udp 0 0 mysite.com:46690 formularfetischiste:ntp ESTABLISHED ntpd 4354 2523/ntpd udp 0 0 mysite.com:35009 stratum-2-core-a.qu:ntp ESTABLISHED ntpd 4356 2523/ntpd udp 0 0 mysite.com:58702 stratum-2-core-a.qu:ntp ESTABLISHED ntpd 3770 2522/ntpd udp 0 0 mysite.com:49583 merlin.ensma.fr:ntp ESTABLISHED ntpd 4355 2523/ntpd udp 0 0 mysite.com:56290 beast.syus.org:ntp ESTABLISHED ntpd 3771 2522/ntpd

  Read the article

• Windows Home 7 and virtualization

  - by progtick

  so apparently, you can't use VirtualBox etc with Windows Home 7. because you would be using two licenses instead of one. So other users that tried virtualization with Windows Home Premium 7, did you just end up using another OS like Ubuntu etc? Did you find a workaround for using Windows? When I say virtualization, I mean virtual machine of sort - where dangerous websites can be visited, nasty applications can be tried etc.

  Read the article

• Run VirtualBox in background, without a window

  - by Bashman

  Hi! I was wandering if it's possible to run an Ubuntu virtual machine using VirtualBox in background, I mean, without any window open. The idea is to conect via SSH to the linux host, that would be running in background. Have you ever done somenthing like this? Is it possible? Thanks!

  Read the article

• mongodb : Can create new thread on FreeBSD?

  - by user197739

  We experienced some strange thing in our mongodb gridfs platform. The platform actually is a bi Xeon E5 (bi quad core) with 128GB of memory, running on freebsd 9 with a zfs pool dedicated for mongodb. [root@mongofile1 ~]# uname -sr FreeBSD 9.1-RELEASE our /boot/loader.conf vfs.zfs.arc_min="2048M" vfs.zfs.arc_max="7680M" vm.kmem_size_max="16G" vm.kmem_size="12G" vfs.zfs.prefetch_disable="1" kern.ipc.nmbclusters="32768" /etc/sysctl.conf net.inet.tcp.msl=15000 net.inet.tcp.keepidle=300000 kern.ipc.nmbclusters=32768 kern.ipc.maxsockbuf=2097152 kern.ipc.somaxconn=8192 kern.maxfiles=65536 kern.maxfilesperproc=32768 net.inet.tcp.delayed_ack=0 net.inet.tcp.sendspace=65535 net.inet.udp.recvspace=65535 net.inet.udp.maxdgram=57344 net.local.stream.recvspace=65535 net.local.stream.sendspace=65535 we follow the recommendation for the ulimit : [root@mongofile1 ~]# su - mongodb $ ulimit -a cpu time (seconds, -t) unlimited file size (512-blocks, -f) unlimited data seg size (kbytes, -d) 33554432 stack size (kbytes, -s) 524288 core file size (512-blocks, -c) unlimited max memory size (kbytes, -m) unlimited locked memory (kbytes, -l) unlimited max user processes (-u) 5547 open files (-n) 32768 virtual mem size (kbytes, -v) unlimited swap limit (kbytes, -w) unlimited sbsize (bytes, -b) unlimited pseudo-terminals (-p) unlimited This server have a twin (same config exactly) for ReplSet in other data center and we have a virtualized arbiter. Some time, almost 3 days, the process of mongodb exit. The problem begin with: Fri Nov 8 11:27:31.741 [conn774697] end connection 192.168.10.162:47963 (23 connections now open) Fri Nov 8 11:27:31.770 [initandlisten] can't create new thread, closing connection Fri Nov 8 11:27:31.771 [rsHealthPoll] replSet member mongofile2:27017 is now in state DOWN Fri Nov 8 11:27:31.774 [initandlisten] connection accepted from 192.168.10.162:47968 #774702 (20 connections now open) Fri Nov 8 11:27:31.774 [initandlisten] connection accepted from 192.168.10.161:28522 #774703 (21 connections now open) Fri Nov 8 11:27:31.774 [initandlisten] connection accepted from 192.168.10.164:15406 #774704 (22 connections now open) Fri Nov 8 11:27:31.774 [initandlisten] connection accepted from 192.168.10.163:25750 #774705 (23 connections now open) Fri Nov 8 11:27:31.810 [initandlisten] connection accepted from 192.168.10.182:20779 #774706 (24 connections now open) Fri Nov 8 11:27:31.855 [initandlisten] connection accepted from 192.168.10.161:28524 #774707 (25 connections now open) Fri Nov 8 11:27:31.869 [initandlisten] connection accepted from 192.168.10.182:20786 #774708 (26 connections now open) and after many "can create new thread" [root@mongofile1 /usr/mongodb]# tail -n 15000 mongod.log.old |grep "create new thread"|wc 5020 55220 421680 and finish by a magnificent Fri Nov 8 11:30:22.333 [rsMgr] replSet warning caught unexpected exception in electSelf() pure virtual method called Fri Nov 8 11:30:22.333 Got signal: 6 (Abort trap: 6). Fri Nov 8 11:30:22.337 Backtrace: 0x599efc 0x8035cb516 0x599efc <_ZN5mongo10abruptQuitEi+988> at /usr/local/bin/mongod 0x8035cb516 <_pthread_sigmask+918> at /lib/libthr.so.3 Extract of mongodb from top 78126 mongodb 77 20 0 1253G 1449M sbwait 0 0:20 0.00% mongod If I restart the process when it crash, the problem is fixed for almost 3 days. Has anyone seen this before, or know of a fix?

  Read the article

• How to test if DNS information has propagated?

  - by Andrew

  I set up a new DNS entry for one of my subdomains (I haven't set up any Apache virtual hosts or anything like that yet). How can I check that the DNS information has propagated? I assumed that I could simply ping my.subdomain.com and assume that if it could resolve, it would show the IP address I specified in the A record. However, I don't know if I am assuming correctly. What is the best way to check this information?

  Read the article

• Subdomain not hitting new site?

  - by Abe Miessler

  I have an existing site at my.site.com and I would like to setup a staging subdomain (staging.my.site.com). I have my DNS setup and directing staging.my.site.com to my server, but for some reason the Web Site I created in IIS for it is not being hit. Instead when I go to staging.my.site.com it takes me to the original site. The site I created in IIS has a home directory that is totally different from the regular sites home directory. I have added one host header with the following information: IP Address: (All Unassigned) TCP port: 80 Host Header Value: staging.my.site.com I was under the impression that with the setup I described above hitting staging.my.site.com through a web browser would bring up the staging site, but it does not. Can anyone see what I am doing wrong? UPDATE: One thing I noticed is that in my A record I am mapping to the IP Address ( lets say 1.1.1.1 for this example). In the host headers for the main site (my.site.com) it has 1.1.1.1 as an entry. Is this normal? Could it cause the problem I am talking about?

  Read the article

• Moving my OpenID from Livejournal to... something else.

  - by T-Boy

  I've actually been an early user of OpenID, although there are still some questions that I've had with OpenID that I've never really had satisfactorily answered. Now, I understand that if I have full control over my domain, I can set it up so that I can delegate the task of authenticating to another OpenID service provider. The problem is, what I'd like to do is to get the Livejournal server to pass the authentication to someone else, instead of having LJ doing it. Preferably what I'd like to do is get Livejournal, when asked by a authenticating provider, say, "No, I don't do it anymore -- go to this address". The plan was that this address would then be in a domain I fully control, which then would pass it on to whichever service provider I choose. I don't even know if I've gotten my understanding of OpenID right, if all this shenanigans are necessary, if my question makes sense, or if it's even possible with a service provider like Livejournal. (tried tagging this with livejournal, and it told me I couldn't, because I don't have enough reputation. Oh well; one must start somewhere. Sorry for the inconvenience!)

  Read the article

• using gmail as email relay for sendmail

  - by Nikita

  I used to be able to send emails using a gmail account & sendmail configured using one of the guides on the Internet, for example: http://appgirl.net/blog/configuring-sendmail-to-relay-through-gmail-smtp/ This is a small server and I've recently moved it to a different house. And sendmail has stop working. The only thing different in the network setup is a new router. What is happening: In the log files, I see the following error: ...stat=Deferred: smtp.gmail.com: No route to host When I run from the command line: strace sendmail -f A -t B -u "Subject" -m "Message" -tls=yes ssl=yes -s smtp.gmail.com:587 -xu A -xp XYZ It hangs on this call: recvfrom(3, "m0\201\203\0\1\0\0\0\0\0\0\4ares\3lan\0\0\34\0\1", 8192, 0, {sa_family=AF_INET, sin_port=htons(53), sin_addr=inet_addr("192.168.1.254")}, [16]) = 26 close(3) = 0 time(NULL) = 1339997943 open("/etc/localtime", O_RDONLY) = 3 fstat64(3, {st_mode=S_IFREG|0644, st_size=3477, ...}) = 0 fstat64(3, {st_mode=S_IFREG|0644, st_size=3477, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb76ff000 read(3, "TZif2\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\4\0\0\0\4\0\0\0\0"..., 4096) = 3477 _llseek(3, -24, [3453], SEEK_CUR) = 0 read(3, "\nEST5EDT,M3.2.0,M11.1.0\n", 4096) = 24 close(3) = 0 munmap(0xb76ff000, 4096) = 0 socket(PF_FILE, SOCK_DGRAM|SOCK_CLOEXEC, 0) = 3 connect(3, {sa_family=AF_FILE, path="/dev/log"}, 110) = 0 send(3, "<18>Jun 18 01:39:03 sendmail[268"..., 96, MSG_NOSIGNAL) = 96 nanosleep({60, 0}, So it looks like at some point it tries to resolve the DNS name, but I don't have anything running on 53, so it dies out and then just hangs. The other interesting thing is that msmtp works just fine on the same server. Update: ares in strace output is actually the name of my server, but .254 IP address is the address of the router. Could anyone tell me why this is happening or what further steps can I take to investigate the issue? Thanks!

  Read the article

• WSUS KB978338 Chain of Supersession Incorrect?

  - by Kasius

  The chain appears to be KB978338 to KB978886 to KB2563894 to KB2588516 (newest). All four of these updates are approved on our WSUS server. KB978338 is listing as Not Applicable on all machines, because it has been superseded. This is the behavior I would expect. However, our security office is reporting that KB978338 should still be installed on all machines because its actual effect is not replicated by any of the updates that follow it. Here is the analysis I was sent: KB978886 applies to Vista SP1 only. The rollout of SP2 did not address the ISATAP vulnerability and reintroduces it. KB2563894 only updates two files (Tcpip.sys and Tcpipreg.sys). It does not update the 12 other affected ISATAP, UDP, and NUD .sys and .dll files. (MS11-064) KB2588516 addresses malformed continuous UDP packet overflow. But does not address the ISATAP related NUD and TCP .sys and .dll files. (MS11-083) So yes, many IP vulnerabilities. But each KB addresses specific issues that do not cross over to other KBs. We can install KB978338 by manually running the .MSU file, but we aren't certain if that will overwrite the couple files that get updated by later patches since we would be installing the patch out of order. Is the above analysis correct? Is the chain of supersession incorrectly defined? If it is, what is the proper way to report it so that it can be changed by the correct Microsoft team? We are currently using 32-bit and 64-bit installations of Vista SP2. Note: I should mention that I posted this on Technet as well. I will keep this up-to-date with any information I get on there.

  Read the article

• Window 7 Host does not answer to ping

  - by gencha

  Today I tried printing on a shared printer on one of our homegroup members. Sadly it did not work (printer marked as offline). Shortly after, I noticed I can't even ping the machine that owns the printer (I also can not remotely access it in any other way I've tried). Currently I'm trying to ping the machine from the router both computers are connected to (and my machine in question doesn't answer). I do receive the echo requests (as verified with WireShark). I also added a rule in the Windows Firewall to specifically allow ICMP echo requests, but that didn't change anything. I also tried netsh firewall set icmpsetting 8 enable, but that didn't change anything either. Completely disabling the Windows Firewall has no effect on the issue either. One has to wonder, where does Windows log when and why it ignored any incoming packets? How can I get to the bottom of this? Here are some ways I found to dig deeper into the issue: Enabling logging on the Windows Firewall Enabling Windows Filtering Platform Auditing Both methods at least give more insight into the issue. The plain log file is full of entries like this: 2011-11-11 14:35:27 DROP ICMP 192.168.133.1 192.168.133.128 - - 84 - - - - 8 0 - RECEIVE So the ICMP packets are being dropped as if that was intended. The Event Viewer now gives a little bit more details: The Windows Filtering Platform has blocked a packet. Application Information: Process ID: 4 Application Name: System Network Information: Direction: Inbound Source Address: 192.168.133.1 Source Port: 0 Destination Address: 192.168.133.128 Destination Port: 8 Protocol: 1 Filter Information: Filter Run-Time ID: 214517 Layer Name: Receive/Accept Layer Run-Time ID: 44 This same entry is always repeated with 2 points of information changing: Process ID: 420 Application Name: \device\harddiskvolume2\windows\system32\svchost.exe The service host with the PID 420 is the host for the following services: Windows Audio DHCP Client Windows Event Log HomeGroup Provider TCP/IP NetBIOS Helper Security Center Additionally, there is currently this problem with the same machine: Even though my network is set to be a "Home network", I am unable to create a new homegroup.

  Read the article

• Juniper SSG20 IP settings for email server

  - by codemonkie

  We have 5 usable external static IP addresses leased by our ISP: .49 to .53, where .49 is assigned to the Juniper SSG20 firewall and NATed for 172.16.10.0/24 .50 is assigned to a windows box for web server and domain controller .51 is assigned to another windows box with exchange server (domain: mycompany1.com) mx record is pointing to 20x.xx.xxx.51 Currently there is a policy set for all SMTP incoming traffic addressed to .51 forward to the NATed address of the exchange server box (private IP: 172.16.10.194). We can send and receive emails for both internal and external, but the gmail is saying mails from mycomany1.com is not sent from the same IP as the mx lookup however is from 20x.xx.xxx.49: Received-SPF: neutral (google.com: 20x.xx.xxx.49 is neither permitted nor denied by best guess record for domain of [email protected]) client-ip=20x.xx.xxx.49; Authentication-Results: mx.google.com; spf=neutral (google.com: 20x.xx.xxx.49 is neither permitted nor denied by best guess record for domain of [email protected]) [email protected] and the mx record in global dns space as well as in the domain controller .50 for mail.mycompany1.com is set to 20x.xx.xxx.51 My attempt to resolve the above issue is to Update the mx record from 20x.xx.xxx.51 to 20x.xx.xxx.49 Create a new VIP for SMTP traffic addressed to 20x.xx.xxx.49 to forward to 172.16.10.194 After my changes incoming email stopped working, I believe it has something to do with the Juniper setting that SMTP addressed to .49 is not forwarded to 172.16.10.194 Also, I have been wondering is it mandatory to assign an external static IP address to the Juniper firewall? Any helps appreciated. TIA

  Read the article

• Real-time offline folder-to-folder backup application needed (Windows)

  - by niktech

  I recently started using Intel Matrix Storage RAID solution that allowed me to use my 5 1TB drives for two RAID volumes. First one a 1TB RAID 0 striped across all 5 drives and second one a RAID 5 across the rest of the free space on all drives (around 2.85TB usable space). The RAID 0 I use for OS, applications and games while the RAID 5 I use as a more-permanent type storage (photos, etc). Now I do realize that running the OS and applications on RAID 0 across 5 drives is very dangerous, which is what brings up the following question. Is there a reliable freeware realtime backup application that can backup a set of folders from one drive to another drive (no online backups needed)? I've already tried a few (Mozy, Yadis, Comodo Backup, GFI Backup, Idoo, Crash Plan) but none meet my requirements: Low CPU and RAM usage. Realtime Backups - as soon as a file is modified in the source folder, it is added to the backup queue which will be processed with the lowest priority when the CPU is idle. This backup queue should persist in cases of computer restarts (ie: the source and destination folders should always have the same set of files, except for the ones waiting in the backup queue). Incremental Backups - if only 10 bytes changed in a 1GB file, the app should only copy those 10 new bytes. Ability to back up locked and opened files (some apps, like Yadis, can't back up critical files like browser favorites). Ability to run as a service (no need for any user to log-in to have the app started). Optional requirements: Compression of the destination into a well-known format (RAR, Zip) that can be directly read without the use of the application. Preset source folders (such as Browser Favorites, Game Saves, Application Settings, etc). The idea is to use RAID 0 array as "semi-persistent RAM-like" storage which in case of a failure can be quickly rebuilt by reinstalling the OS, apps and games and copying over the settings, saves, favorites from the RAID 5. I'm also thinking of taking this RAID 0 as RAM idea to the extreme with SSDs (as soon as we get some nice 6Gb/s SATA III SSDs out there), where a couple of SSDs chained in RAID 0 will work as yet another semi-persistent cache layer sitting between the RAM and the HD. I'm just hoping there already exists an application that satisfies these requirements... otherwise I'll have to write one myself, which I would prefer not to do.

  Read the article

• recently used programs stopped updating Vista Home Premium 64

  - by Calum

  For some reason my list of recently used programs has stopped updating. Any program that I "pin" to the start menu remains, but where you would normally expect to see the recent programs is just blank space. What setting do you think could have changed? I don't recall changing anything. Thanks! edit Start MenuProperties Privacy "Store and display a list of recently used programs" is indeed checked.

  Read the article

• OpenVZ with bridged interfaces and VLAN

  - by Deimosfr

  Hi, I've got a problem with OpenVZ with bridged VLAN. Here is my configuration: +------+ +-------+ +-----------+ +---------+ br0 |VE101 | | | | OpenBSD |----->| Debian |------->| | | WAN |--->| Router | | OpenVZ | +------+ | | | Firewall |----->| br0 br1 | br1 +------+ +-------+ +-----------+ +---------+------->|VE102 | |br0 | | |VLAN br0.110 +------+ v +---------+ |VE103.110| +---------+ I can't make VLAN work on br0 (br0.110) and I would like to understand why. I don't have any switch so no problem with unmanageable switch. I've configured a VLAN interface on OpenBSD in /etc/hostname.vlan110: inet 192.168.110.254 255.255.255.0 NONE vlan 110 vlandev sis1 And it seems to be working fine. I've also adapted my PF configuration to work with VLAN but I don't see any incoming traffic. On my Debian Lenny, here is my interfaces configuration : # The loopback network interface auto lo iface lo inet loopback # br0 auto br0 iface br0 inet static address 192.168.100.1 netmask 255.255.255.0 gateway 192.168.100.254 network 192.168.100.0 broadcast 192.168.100.255 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off # VLAN 110 auto br0.110 iface br0.110 inet static address 192.168.110.1 netmask 255.255.255.0 network 192.168.110.0 gateway 192.168.110.254 broadcast 192.168.110.255 pre-up vconfig add br0 110 post-down vconfig rem br0.110 It looks OK, but when I start my VE, here is the message: ... Configure veth devices: veth103.0 Adding interface veth103.0 to bridge br0.110 on CT0 for VE103 can't add veth103.0 to bridge br0.110: Operation not supported VE start in progress... So I've got one error here. I've followed this documentation http://wiki.openvz.org/VLAN but it doesn't work. I've certainly missed something but I don't know why. Someone could help me please? Thanks

  Read the article

• Any 3rd party tools that integrate IIS management with some sort of application inventory/change man

  - by NoCarrier

  I've got an environment with several IIS 6 web servers hosting hundreds of apps (dozens of sites, hundreds of virtual directories) all with a myriad of different configurations belonging to dozens of different developers (all deploying apps willy nilly). Is there some sort of managed software solution that will centralize management of all my IIS6 environments provide some inventory functionality allow for reporting or querying of said application inventory enforce and automate some sort of deployment process?

  Read the article

• Microsoft Exchange Server 2003 offline defragmentation

  - by MitchM

  I have an issue where I don't have enough space to run an offline defragmentation of my exchange database. Can I hook up a 1 TB external HDD (like E: drive) and run the defragmentation process on it.

  Read the article

• How to include worksheet 3 and 4 in a cell formula provided?

  - by user21255

  I have been kindly given this formula with an explanation on how it works: Insert this formula into the cell B4 of the sheet "Cases": =IF(NOT(ISBLANK('1st'!B25)),'1st'!B25,IF(NOT(ISBLANK(INDIRECT("'2nd'!R" & (ROW($B4)-(COUNTA('1st'!$B:$B)-COUNTA('1st'!$B$1:$B$24))-4+25) & "C" & COLUMN(B4),FALSE))),INDIRECT("'2nd'!R" & (ROW($B4)-(COUNTA('1st'!$B:$B)-COUNTA('1st'!$B$1:$B$24))-4+25) & "C" & COLUMN(B4),FALSE),"")) Copy the formula to the other cells in the worksheet; the relative addresses will adjust automatically. The formula works like this: Check if there is content in 1st. If yes, copy it. If no, find out how many entries there are in 1st in total. (This is done by using the COUNTA function on the whole B column in 1st and subtracting the number of non-empty cells above the actual case data.) Use this information together with the current cells's number to find out the location of the cell that has to be copied from 2nd. Create the address of the cell and use the ISBLANK function on the INDIRECT function with that address to check if the cell is empty. If it is not, use the INDIRECT function again to display it. If it is empty, just display an empty string. Now this works fine when I have only 2 sheets. But lets say I want to include a third and fourth sheet (name as 3rd and 4th respectively), then what and should I put the formula for this in the formula above? There are actually 31 sheets but if I know how to add 3rd and 4th sheet in the formula, then I can figure out how to do the rest. Thanks

  Read the article

• Whats the best way to use linux on windows?

  - by rogerstone

  Hi, Hi which is the best way to use linux on windows?I am having windows 7 currently on dell laptop.I want to use linux for development of rails.I have seen that there are a lot options like running directly from usb or cd,installing it,Running it on a virtual box etc... .I would be using linux very frequently.Speed is one of my main concerns.So Which is a good way to go about it for my purpose? Thanks

  Read the article

< Previous Page | 536 537 538 539 540 541 542 543 544 545 546 547  | Next Page >