Search Results

Search found 9235 results on 370 pages for 'social networking'.

Page 56/370 | < Previous Page | 52 53 54 55 56 57 58 59 60 61 62 63 | Next Page >

Problems with wired ethernet connection Ubuntu 11.10

- by Andrew Fielden

After some partition shuffling, I've got a problem on my 11.10 system. The wired ethernet interface fails to come up, although the wireless interface is working. I'm using NetworkManager. I thought this may be a problem with NetworkManager, so I checked the config files, which look ok. I then tried re-installing the package, but this didn't resolve the issues. I'm not sure at this point if the problem is due to software configuration, or a hardware problem. I've also tried the cable in other router ports, but same problem. The symptoms are:- System settings - Network reports that the cable is unplugged (it isn't) ifconfig reports the following eth0 Link encap:Ethernet HWaddr f0:4d:a2:a2:a7:fe UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:792 (792.0 B) TX bytes:0 (0.0 B) Interrupt:46 Base address:0xe000 My /etc/network/interfaces file has the following: auto lo iface lo inet loopback My /etc/resolv.conf file has the following: # Generated by NetworkManager The router's red light is on for this port dmesg reports ADDRCONF(NETDEV_UP): eth0: link is not ready

Read the article
Sharing SCTP connection with multiple threads

- by poly

I have an application that needs to run in SCTP environment, I have a question in sharing the connection among multiple threads for packet receiving only, I've tried with the sctp_sendmsg and it worked without even locking the threads (is that been taking care of by the OS, in other words, is it thread safe to do that). I've tested many cases with the send and I can't see them out of sync. Anyway, back to the receiving, is it possible to create multiple threads and send each thread the sctp descriptor to start receiving messages? Do I need a lock here or is it ok without lock? I'm using C in linux.

Read the article
Multiplayer Network Game - Interpolation and Frame Rate

- by J.C.

Consider the following scenario: Let's say, for sake of example and simplicity, that you have an authoritative game server that sends state to its clients every 45ms. The clients are interpolating state with an interpolation delay of 100 ms. Finally, the clients are rendering a new frame every 15ms. When state is updated on the client, the client time is set from the incoming state update. Each time a frame renders, we take the render time (client time - interpolation delay) and identify a previous and target state to interpolate from. To calculate the interpolation amount/factor, we take the difference of the render time and previous state time and divide by the difference of the target state and previous state times: var factor = ((renderTime - previousStateTime) / (targetStateTime - previousStateTime)) Problem: In the example above, we are effectively displaying the same interpolated state for 3 frames before we collected the next server update and a new client (render) time is set. The rendering is mostly smooth, but there is a dash of jaggedness to it. Question: Given the example above, I'd like to think that the interpolation amount/factor should increase with each frame render to smooth out the movement. Should this be considered and, if so, what is the best way to achieve this given the information from above?

Read the article
Moving AI in a multiplayer game

- by Smallbro

I've been programming a multiplayer game and its coming together very nicely. It uses both TCP and UDP (UDP for movement and TCP for just about everything else). What I was wondering was how I would go about sending multiple moving AI without much lag. At first I used TCP for everything and it was very slow when people moved. I'm currently using a butchered version of this http://corvstudios.com/tutorials/udpMultiplayer.php for my movement system and I'm wondering what the best method of sending AI movements is. By movements I mean the AI chooses left/right/up/down and the player can see this happening. Thanks.

Read the article
VPN disconnected: resolv.conf not refreshed

- by cwall

I connect to VPN using vpnc. When VPN disconnects, either via time out or the session limit is reached, VPN is terminated, but resolve.conf continues to contain references to my VPN network. resolv.conf before VPN is connected: nameserver 127.0.0.1 search mylocalnetwork resolv.conf after VPN is connected and remains once VPN is lost: nameserver X.X.X.X nameserver X.X.X.Z nameserver 127.0.0.1 search internal.mycompany.com mylocalnetwork In 10.04, when VPN lost, I'd run this script to refresh resolve.conf: 7$ cat bin/refreshResolvconf.sh #!/bin/bash #if [ -e /etc/resolvconf/run/interface/tun0 -a "`pidof vpnc`" == "" ]; then /sbin/resolvconf -d tun0; fi if [ -e /etc/resolvconf/run/interface/tun0 -a "`pidof vpnc`" == "" ] then /sbin/resolvconf -d tun0; echo "Refreshed resolv.conf" fi But, resolveconf changed in 12.04 changed, so this script is no longer applicable. To resolve, I manually edit resolve.conf or turn off/on my connection via "gnome-control-center network". Anyone else have the same problem? How can resolv.conf be updated post-VPN disconnect?

Read the article
How to promote/market an event that needs many people?

- by stjowa

My team is about to launch a new web application, http://wethepixels.com, that requires a lot of people to be on the site at the same time for the concept to be successful. Our team is preparing to promote/market an event for a specific date and time, in order to try to grab a large group of people to the site at once. For those who have gone through a similar web launch, we would love to hear ideas on the best way to market for a large group in a relatively short period of time. We have created a Facebook page and a Facebook event, but it has yet to grab much attention (surprisingly to us). Is there a better way to attract a large number of users in a short period of time? Thanks

Read the article
Ping Access to a Nested VM !! Plz Help

- by Shivaramakrishnan

I have a problem in communication between the host and the nested VM.This is my layout. I have installed KVM on host machine having a single nic interface (public ip) running Ubuntu.On top of this,I have VM running Ubuntu.I have installed KVM in this VM too.I then have a VM inside this running a web server. I am able to ping the host from this web server VM and ssh into it.But from host to VM ,ping is being unsuccessful. The VM (named L1hyp) on host was created using libvirt-manager and has IP of 192.168.122.8. The vswitch interface created at host is in default config (NAT-ed). Its IP is 192.168.122.1. Now this VM is also having a vswitch interface which is in default config (NAT-ed).Its IP is 192.168.100.1. The Web server VM is created on top of this L1hyp VM, is having an IP of 192.168.100.186. The Webserver VM uses 192.168.100.1 as its default gw. The L1hyp uses 192.168.122.1 as its default gw. From Host: ping 192.168.122.8 - SUCCEEDS ping 192.168.122.1 - SUCCEEDS ping 192.168.100.1 - SUCCEEDS ping 192.168.100.186 - FAILS Comes up with Destination Host Unreachable From 192.168.122.1. But there is route to 192.168.100.0/24 subnet from host.Ping to 192.168.100.1 succeeds. From Webserver VM: ping 192.168.100.1 - SUCCEEDS ping 192.168.122.1 - SUCCEEDS SSH from web server VM to host succeeds. Can anyone help me out what needs to be modified to have two way communication between the host and Webserver VM at the earliest? I am pondering over this problem for over a week now.

Read the article
How to connect to a serverside process on Ubuntu running in a VM?

- by Jenko

I am running Ubuntu 11.10 in VirtualBox, on Windows 7. I'm trying to setup a serverside process like Apache on it. How do I configure VirtualBox to allow access to the Ubuntu server process from other computers on the network? I can access the internet from Ubuntu. The Windows 7 computer is on a WiFi network using DHCP. The WiFi network has a dynamic IP with the network provider. This is my current configuration:

Read the article
No wireless network recognized on a Dell Vostro 3560

- by Itai

I just installed Ubuntu 12.04 along with Windows 7 on the same laptop - Dell Vostro 3560. Now, on Windows 7 I can access to different wi-fi networks. However, when I am logging onto the Ubuntu section (after re-starting my laptop) - an error message appears: Disconnected - you are now offline When I take a look at my network menu (in the upper bar on the screen), I see that no network is found (and I have a few of them in the area. ). I tried to look around but really could not find a concrete practical solution to this specific problem, would appreciate any solution from anyone out there that had this problem and solved it.

Read the article
Create personal wireless network on laptop

- by TechGuru

I have a WiFi Network, now I have connected my laptop to the WiFi Network. And it is working fine I'm able to access the internet via WiFi. But I want to create other network on my laptop so that I can connect my mobile phone to the my laptop network. Means, my laptop is already connected to WiFi network (xyz). Now I want to create one wireless network on my laptop. So that I can connect my mobile phone to laptop network and access the internet on mobile. But I don't want to lost my `laptop and WiFi connection that is already connected. I tried to create the wireless network on my laptop, but when I created my personal wireless network I lost my wifi-laptop connection. I don't know it is possible or not.

Read the article
Problems connecting to eduroam wifi - ubuntu touch

- by Fiona Cox

I am trying to connect to our university's eduroam wi-fi network with my Nexus 4 running Ubuntu touch (utopic latest build), but can't get past the first stage. I wonder if anyone can help please? I am following these instructions (which worked for my iPhone): http://www.st-andrews.ac.uk/itsupport/mobile/eduroam/ But when I go to the bandit.st-andrews.ac.uk/connect page then follow the link to 'eduroam setup' I get the error message: Authorization Required This server could not verify that you are authorised to access the document requested. Either you supplied the wrong credentials (e.g., bad password), or your browser doesn't understand how to supply the credentials required. Apache/2.2.16 (Debian) Server at bandit.st-andrews.ac.uk Port 443 (Clearly it's the latter option (browser) as I haven't been asked for my credentials yet.) Is there a way round this, or am I just not going to be able to connect until further down the Ubuntu touch development road... Thanks!

Read the article
How to share a folder without any issues when we have >20 machines in LAN ?

- by Gaurang Agrawal

Till date I have been sharing files through workgroup , using samba but I presume that this is not the right way as I had been facing so many issues with one or another computer . Machines are having same workgroup but even then problems are there . What will be the best way to handle this kind of issue ? PS : I am helping a school migrate from Windows to Ubuntu 12.04 LTS ( Teachers collaborate by working on different files saved in a shared folder in one of the computer )

Read the article
both IPV4 and IPV6 at the same time over DSL connection?

- by namiheike

Let me describe my situation: while I connect computer with the wire, I've got an IPV6 address automatically, there's a "Wired connection" tab in network manager, and I can access an website that support IPV6 (google,facebook,twitter...)with a hosts file, or use the proxy like google.com.sixxs.org But if I want to access the whole internet, I have to create a DSL connection with username and password that ISP gave me. BUT after I change my connection into this DSL connection, I cannot access website over IPV6, even there's the site's ipv6 address in /etc/hosts, then I realize that I lose my IPV6 connection, because the ping6 says connect: Network is unreachable. the problem is, there's no IPV6 tab or options about IPV6 in the configure of DSL connection. It feels like I can only use one connection at the same time, but the DSL doesn't support IPV6 and the wired connection doesn't support IPV4(I mean, there's no way to input the password the ISP gave me) maybe make somebody uncomfortable, but when I work in MS windows, there's no such problem, (maybe just feel like) I can access V4 and V6 at the same time. So how to solve with this? thanks a lot. I'm in 11.10 + gnome3

Read the article
Yoga Pro 2 Wi-Fi not working

- by user293004

I installed Ubuntu 14.04 on my new Yoga Pro 2 and the wireless is not working. It started with Windows 8 on it. The Network Manager says Wi-Fi is disabled by hardware switch. I tried putting a blacklist file in ect/modprobe.d as has been suggested in many places. I called the file "blacklist-ideapad_laptop.conf" and wrote in the file blacklist ideapad_laptop I checked to make sure that the wireless is enabled in the BIOS. It is. I ran rfkill list all and it displayed: 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes I ran iwlist wlan0 scan and it displayed: wlan0 Failed to read scan data : Network is down I ran sudo rmmod ideapad_laptop and it displayed: rmmod: ERROR: Module ideapad_laptop is not currently loaded. I ran ifconfig wlp1s0 up and it displayed: wlp1s0: ERROR while getting interface flags: No such device. I ran "lspci" and it displayed: 01:00.0 Network controller: Intel Corporation Wireless 7260 (rev 6b) I ran sudo lshw -c network and it displayed: *-network DISABLED description: Wireless interface product: Wireless 7260 vendor: Intel Corporation physical id: 0<br> bus info: pci@0000:01:00:0.0 logical name: wlan0 version: 6b serial: 7c:7a:91:5f:9b:fa width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.13.0-24-generic firmware=22.24.8.0 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:61 memory:b0400000-b0401fff This No wireless with Intel Centrino Advanced-N 7260 seems to be dealing with a similar issue. It suggests that I need to update my firmware. So I downloaded iwlwifi-7260-ucode-23.214.9.0 from Intel's website. I put the file "iwlwifi-7260-9.ucode" in /lib/firmware and ran "sudo lshw -c network" again. It displayed exactly as before. Is there something else I need to do install the new firmware?

Read the article
Can't connect to or see my wifi ssid

- by ant

Today I installed ubuntu 12.04 on my laptop. I am unable to see my home SSID or even connect to it. I've tried to connect as a hidden SSID but I always get prompted for authorization although my key is correct. I'm in in Europe but my laptop is from US. I'm not sure if that is relevant. I've read around this site and saw something that has to do with setting the channel above 11. I'm not sure I did that correctly I did this : How to use Wi-Fi channels above 11? Did't help. I'm able to connect with cable but not via wifi either windows or linux. Other devices in my home can connect without any issues, even the kindle. Here is the screenshot from my router : Here is some additional info : lspci | grep -i network 08:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01) lspci -nnk | grep -A2 0280 08:00.0 Network controller [0280]: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01) Subsystem: Hewlett-Packard Company U98Z062.10 802.11bgn Wireless Half-size Mini PCIe Card [103c:303f] Kernel driver in use: ath9k m-tool NetworkManager Tool State: connected (global) Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: ath9k State: disconnected Default: no HW Address: 90:4C:E5:38:79:0D Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes I'm not sure what to do next. Any suggestions?

Read the article
No Wireless In Ubuntu 13.10

- by viktorhubinette

When I upgraded to Ubuntu 13.10, I can't connect to wireless. The only thing I can connect to is ethernet, so please help me, What should I do? Here is the output of the lspci -nnk | grep -i net -A2 00:19.0 ethernet controller [0200]:intel corporation 82579V Gigabit network connection [8086:1503] (rev 04) subsystem: acer incorporated [ALI Device] [1025:8000] Kernel driver in use : e100e output of lsusb: Bus 002 Device 003: ID 046d:c31c Logitech, Inc. Keyboard K120 for Business Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 0bda:0152 Realtek Semiconductor Corp. Mass Storage Device Bus 001 Device 040: ID 04e8:6863 Samsung Electronics Co., Ltd Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 004: ID 0bda:8178 Realtek Semiconductor Corp. RTL8192CU 802.11n WLAN Adapter Bus 003 Device 003: ID 045e:070f Microsoft Corp. Bus 003 Device 002: ID 046d:c52f Logitech, Inc. Unifying Receiver Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

Read the article
RPC protocols comparison

- by Ricardo

I have to select a protocol/technology to use for communicating a client-server architecture, with support both for Python and C. The main requirements are: Symmetrical communication in between ends: clients establish a connection and servers can send data back to clients through the same connection. Avoid excessive overhead by using HTTP or a big stack (if possible, TCP direct communication). TLS/SSL support for secure communications. Ease of implementation. For that, I evaluated the following protocols/communications technologies. Is the information on this table accurate and correct? (*1) TLS support for RPyC is based in a no-longer supported Python library.

Read the article
Is it possible to set a VPN through Tor? and have functionality for Software Updates?

- by moazhmi

Gday, I have been trying to do a software update on Trusty both on terminal and software update app but that hasnt been successful, apparently my ISP has a broken transparent proxy. moazhmi@moazhmi-K52F:~$ wget -S http://extras.ubuntu.com/ubuntu/dists/trusty/InRelease --2014-06-04 17:34:52-- http://extras.ubuntu.com/ubuntu/dists/trusty/InRelease Resolving extras.ubuntu.com (extras.ubuntu.com)... 91.189.92.152 Connecting to extras.ubuntu.com (extras.ubuntu.com)|91.189.92.152|:80... connected. HTTP request sent, awaiting response... HTTP/1.1 200 OK Content-Type: text/html; charset=UTF-8 Content-Length: 213 Date: Wed, 04 Jun 2014 14:34:52 GMT Server: Apache/2.2.22 (Ubuntu) Connection: Keep-Alive Vary: Accept-Encoding Length: 213 [text/html] Saving to: ‘InRelease’ 100%[======================================>] 213 --.-K/s in 0s 2014-06-04 17:34:52 (22.1 MB/s) - ‘InRelease’ saved [213/213] I was advised to refer back to the ISP with a complaint but that has returned with peanuts. My Question is - Is it possible to set a VPN through TOR , i.e whereas I can run software updates through terminals or the app . the browsing is out of question here as I need to update which I am not able to do / only on 12.04.

Read the article
Unable to connect to the Internet via LAN despite the connection showing as established

- by Vikram

I have installed Ubuntu 11.10. I am facing a problem connecting via LAN. We have a firewalled network. After entering static IP, gateway, DNS, etc., it shows connection as established but we are unable to use the Internet using the wired connection (LAN). While checking system testing following error shows under network test: ERROR:root:Could not find def gateway info in /proc ERROR:root:Could not find default gateway by running route

Read the article
wifi not working hp dv4

- by Blaze

i get this output for sudo lshw -C network : *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: 06 serial: 3c:4a:92:cd:63:98 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff *-network DISABLED description: Wireless interface product: RT5390 [802.11 b/g/n 1T1R G-band PCI Express Single Chip] vendor: Ralink corp. physical id: 0 bus info: pci@0000:0a:00.0 logical name: wlan0 version: 00 serial: 90:00:4e:82:3c:5b width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.0.0-17-generic-pae firmware=0.34 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:c2500000-c250ffff i cant enable the wifi using the fn+f12 key.. its just stuck. In windows 7 it gets enabled when i press the same keys. but this happens after it gets booted up... i just want to use the wifi in anyway possible. can anybody help?

Read the article
Ubuntu connects to wireless but doesn't work!

- by UbuntuUser990

I just installed Ubuntu 14.04 LTS on my laptop, it connects to my wireless network and shows that it is connected, but when I try to load a webpage or do anything like download Steam for Dota 2, it doesn't work. When I try to connect my Facebook account to Ubuntu, it doesn't work. I want to be able to use Ubuntu with working internet access. What do I do?. ifconfig this shows up eth0 Link encap:Ethernet HWaddr 88:ae:1d:60:56:eb inet addr:192.168.1.13 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:24 errors:0 dropped:0 overruns:0 frame:0 TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1856 (1.8 KB) TX bytes:1856 (1.8 KB) When I type ping askubuntu.com this shows up ping: unknown host askubuntu.com

Read the article
Dirt Cheap Bi-Directional Antenna Wirelessly Extends Your LAN

- by Jason Fitzpatrick

If you’re looking for an effective way to link remote LANs without the hassle of laying cable, this DIY bi-directional antenna is a quick (and cheap) method for bringing internet access to outbuildings and other locations. Tinker Danilo Larizza needed to share internet access between apartments that are relatively close together but not hardwired–ruling out simply sharing the access via existing LAN infrastructure. His solution combines a simple scrap wire antenna array mounted inside a plastic food bin (seen here with the cover removed to show the antenna) and some coaxial cable to link the antenna to two routers. Our favorite part about his build is that he constructed the pair to establish if the antenna setup would even work in his location and intended to buy commercial antennas if it did; his Tupperware models worked so well, however, they’re now the permanent solution. Hit up the link below for more information about the project. 2.4 Ghz Directive Biquad Antenna [via Hack A Day] How To Use USB Drives With the Nexus 7 and Other Android Devices Why Does 64-Bit Windows Need a Separate “Program Files (x86)” Folder? Why Your Android Phone Isn’t Getting Operating System Updates and What You Can Do About It

Read the article
MAAS and Openstack Network

- by user281985

Trying to figure out the best way for openstack and MASS networks to co-exist. Assuming MAAS used 10.0.0.0/24 for provisioning of various openstack nodes, once openstack, with quantum, is deployed should 10.0.0.0 be used as management network, external network, both or discarded? Reason for the question being that I ran a deployment where openstack used 10.0.0.0 as its management network, MAAS dhcp and dns were active; however, I could only access VMs through namespace and was not able to utilize MAAS's dhcp to assign floating IP. (VMs network was through an internal bridge 10.10.10.10, and external bridge was using the same interface as MAAS.) Any thoughts or ideas are appreciated.

Read the article
Changing internal home network ip address for connected devices

- by oshirowanen

I have a few computers at home. For each of the computers, I can see the internal home network ip address on any given device by typing in ifconfig in the terminal. If the device is connected to the home network via ethernet connection or via the built-in wireless connections in laptops, the internal ip address for each of the devices seems to be 192.168.0.X. However, when I connect one of the devices using an external usb modem wireless adapter, which connects to the home network through wireless, when I check the ip address via ifconfig, for some reason it gets assigned 192.168.42.X instead. Why are the ethernet and build in wireless connections getting 192.168.0.X, but the external usb wireless adapter gets 192.168.42.X? Most importantly, is it possible to force it to get an internal ip address of 192.168.0.X?

Read the article
MAAS. Adding nodes

- by 2bus.erkanat

Can anybody help me with MAAS installation? I installed it on 1 of my computers, configured DHCP server and now 3 PCs are in their own private network. I tried to add node via PXE image, but "Can not apply stage final, no datasource found! Likely bad things to come!" error comes after giving me option to log in. Then I tried to add node via web interface, but after adding it node's status is always "commisioning". So what should I do know? Any help is appreciated. Thank you P.S. English is not my native language, sorry for any type of errors.

Read the article

< Previous Page | 52 53 54 55 56 57 58 59 60 61 62 63 | Next Page >