Search Results

Search found 9235 results on 370 pages for 'social networking'.

Page 60/370 | < Previous Page | 56 57 58 59 60 61 62 63 64 65 66 67  | Next Page >

  • wireless card not detected

    - by user281219
    i have a old HP Compaq NX6125 with a new lunbuntu 14.04 32 bits install , but the wireless card is not working I have already done this steps and the wireless leds on the laptop are on but can't see any where the wireless interface , cloud`t do the last two steps . sudo apt-get remove bcmwl-kernel-source sudo apt-get install firmware-b43-installer b43-fwcutter Then Reboot And you need to activate the card from settings/network/wireless make it ON After this search for wireless icon at the task bar and look for your wifi. lshw -class network: *-network:0 description: Ethernet interface product: NetXtreme BCM5788 Gigabit Ethernet vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:02:01.0 logical name: eth0 version: 03 serial: 00:0f:b0:f7:d1:0f size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.134 duplex=full firmware=5788-v3.26 ip=192.168.1.120 latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:23 memory:d0000000-d000ffff *-network:1 description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:22 memory:d0010000-d0011fff *-network description: Wireless interface physical id: 1 logical name: wlan2 serial: 00:14:a5:77:9e:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.13.0-29-generic firmware=666.2 link=no multicast=yes wireless=IEEE 802.11bg

    Read the article

  • Ubuntu 12.10 - VirtualBox not sharing internet with guest system

    - by Fernando Briano
    I went from ArchLinux to Ubuntu on my dev box. I use VirtualBox to test web sites on Windows and IE. I have my Windows 7 VirtualBox image running on Ubuntu's VirtualBox. Back with ArchLinux, internet worked "out of the box" on the Windows boxes. I left the default options on the box's Network Options (NAT). The Windows machine shows as "connected to ethernet" but reports: The dns server isn't responding So I can't access Internet from there. I tried searching for Ubuntu's official docs but they seem pretty outdated. I tried using my old boxes from Arch (which boot normally but have no internet) and creating a new box from Ubuntu itself, but still get the same results. Update: I'm using VirtualBox 4.1.18 from Ubuntu's repository (apt-get install virtualbox).

    Read the article

  • Why dhclient is still running when I choose static IP?

    - by user276851
    I modify dhcp to static in /etc/network/interfaces (like below). # The primary network interface auto eth0 iface eth0 inet static netmask 255.255.0.0 address 10.10.130.128 gateway 10.10.1.1 Then restart the interface. $ sudo ifdown eth0; sudo ifup eth0 ... $ ifconfig eth0 Link encap:Ethernet inet addr:10.10.130.128 Bcast:10.10.255.255 Mask:255.255.0.0 So the new address kicks in. But DHCP is still there? $ ps aux | grep dhc root ... dhclient3 -e IF_METRIC=100 -pf /var/run/dhclient.eth0.pid -lf /var/lib/dhcp/dhclient.eth0.leases -1 eth0 Is that normal? If not, how to restart interface in static IP while stop DHCP at the same time? Thanks a lot.

    Read the article

  • Connected to wireless, but no internet access

    - by boogaloo
    After installing Ubuntu 12.04 a week ago wireless internet had been working fine. It stopped working yesterday, however, and I'm at a loss for what to do even after scouring replies to similar posted problems. I have tried using Google's public DNS and turning off proxy settings on Firefox. I have used nm-tool and lshw to make sure my wireless device and driver are connected. If anyone can help me resolve this issue I would be extremely grateful! @kregerjd $ ping -c3 www.google.com ping: unknown host www.google.com @Alaa: $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 192.168.1.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 $ ping -c4 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data From 192.168.1.104 icmp_seq=1 Destination Host Unavailable From 192.168.1.104 icmp_seq=2 Destination Host Unavailable --- 192.168.1.1 ping statistics --- 4 packets transmitted, 0 received, +2 errors, 100% packet loss, time 2998ms pipe 4

    Read the article

  • Sending state diffs (deltas) and unreliable connections

    - by spaceOwl
    We're building a realtime multiplayer game, in which each player is responsible for reporting its state on every iteration of the game loop. The state updates are broadcasted using unreliable UDP. To minimize state data sending, we've come up with a system that will send only deltas (whatever state data that was changed). This method however is flawed, since a lost packet will mean that other players will not receive the delta, making the game behave in an unexpected way. For example: Assume that state is comprised of: { positionX, positionY, health } Frame 1 - positionX changed --> send a packet with positionX only. Frame 2 - health changed // lost ! Frame 3 - positionY changed --> send a packet with positionY only. // Other players don't know about health change. How can one overcome this issue then? sending the entire data is not always feasible.

    Read the article

  • Wifi is connected but internet not working?

    - by Philip
    I have a lenovo x230 running ubuntu 12.04lts. I've been using it just fine for a while, but all of a sudden the internet's stopped working. It's connected to the router just fine (I can see the antenna bars saying it's connected) but when I try to go to a webpage, it's just loading forever. I've tried the fix listed here (http://ubuntuforums.org/showthread.php?t=1985079) but it hasn't done anything (the instructions are a little confusing though). I'm booting windows 7 right now and the internet works just fine when I'm on windows, so I know it must be a problem with ubuntu. I haven't touched any network settings before this problem happened, and I've been using it just fine for months, so I don't know why I'm getting this problem all of a sudden. Oh and I haven't updated anything in a few weeks (you know when the update manager pops up every so often listing all the things there's an update for) so I know it's not some update that broke it.

    Read the article

  • The Internet Key Wave MW833UP is not recognized in Ubuntu

    - by gio900
    I can't use my Onda MW833UP... :( Any advice? Here is something that someone else may understand: ~$: lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 11.10 Release: 11.10 Codename: oneiric ~$: lsusb Bus 001 Device 005: ID 1ee8:0012 ~$: dmesg [ 22.709475] cdc_acm 1-1:1.0: ttyACM0: USB ACM device [ 22.714856] usbcore: registered new interface driver cdc_acm [ 22.714866] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 23.520490] ieee80211 phy0: wl_ops_bss_info_changed: arp filtering: enabled true, count 1 (implement) [ 24.244530] usbcore: registered new interface driver usbserial [ 24.244575] USB Serial support registered for generic [ 24.244673] usbcore: registered new interface driver usbserial_generic [ 24.244681] usbserial: USB Serial Driver core [ 24.265879] USB Serial support registered for GSM modem (1-port) [ 24.285680] usbcore: registered new interface driver option [ 24.285691] option: v0.7.2:USB Driver for GSM modems [ 24.425878] EXT4-fs (sda9): re-mounted. Opts: errors=remount-ro,commit=600 [ 24.736540] EXT4-fs (sda8): re-mounted. Opts: commit=600 [ 35.705796] Easy slow down manager: checking for SABI support. [ 35.706002] Easy slow down manager: SABI is supported (f5189) [ 36.060099] usbcore: deregistering interface driver uvcvideo [ 139.508061] CE: hpet increased min_delta_ns to 20113 nsec [ 6798.378917] usb 1-1: USB disconnect, device number 5 [ 6809.108232] usb 1-1: new high speed USB device number 6 using ehci_hcd [ 6809.242692] scsi5 : usb-storage 1-1:1.0 [ 6810.241257] scsi 5:0:0:0: CD-ROM Onda Datacard CD-ROM 0001 PQ: 0 ANSI: 0 [ 6810.241841] scsi 5:0:0:1: Direct-Access Onda Storage 0001 PQ: 0 ANSI: 0 [ 6810.271410] sr0: scsi3-mmc drive: 0x/0x caddy [ 6810.272099] sr 5:0:0:0: Attached scsi CD-ROM sr0 [ 6810.272852] sr 5:0:0:0: Attached scsi generic sg1 type 5 [ 6810.279954] sd 5:0:0:1: [sdb] Attached SCSI removable disk [ 6810.281210] sd 5:0:0:1: Attached scsi generic sg2 type 0 [ 6810.380591] sr0: CDROM (ioctl) error, command: Xpwrite, Read disk info 51 00 00 00 00 00 00 00 02 00 [ 6810.380617] sr: Sense Key : Hardware Error [current] [ 6810.380625] sr: Add. Sense: No additional sense information [ 6810.613937] sr0: CDROM (ioctl) error, command: Xpwrite, Read disk info 51 00 00 00 00 00 00 00 02 00 [ 6810.613972] sr: Sense Key : Hardware Error [current] [ 6810.613984] sr: Add. Sense: No additional sense information [ 6810.673716] usb 1-1: USB disconnect, device number 6 [ 6815.572142] usb 1-1: new high speed USB device number 7 using ehci_hcd [ 6815.706828] cdc_acm 1-1:1.0: ttyACM0: USB ACM device The last 3 lines are where I inserted the Internet key, then reconnected it. usb-device T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 7 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1ee8 ProdID=0012 Rev=00.01 S: Manufacturer=Onda S: Product=MW833UP S: SerialNumber=9230B35D870F9CB7AE684EACC5C12BE5EC33B26E C: #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=01 Driver=cdc_acm I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm Then there is /dev/ttyACM0. When the key is connected to the USB port, everything that will meant...

    Read the article

  • Wifi networks will not show up!

    - by Kcahmadi
    I'm running Ubuntu 14.04 on an old '08 macbook. I've gone to system settingsSoftware & UpdatesAdditional Drivers and enabled the wireless driver. But when I click the wifi icon on the top toolbar no networks show up. When running lshw it clearly shows my wireless card under Network controller and it says the driver is installed. However, nm-tool only shows ethernet. And rfkill only shows bluetooth. What can I do?

    Read the article

  • Remote connection problem.

    - by Woody
    Hello I have ubuntu 10.04 installed with mysql on it and I have a problem with remote connection. When I connect through putty it works but sometimes it looks like it hangs for example when I execute the command ln --help. Also with MySQL connection When I execute a simple query like show processlist; it works, but for example select * from table not always, if the table doesn't have many rows it works but if it has let's say more than 20 the query looks like it keeps working and never ends. It's connected but I can't do many things remotely. Added: I connect using putty from other windows pc, server is not overloaded. when i work at the same time directly on ubuntu i can do everything. Remotely not.

    Read the article

  • How to prevent WLAN connection from dropping permanently?

    - by Chris
    I have a desktop with a Fritz USB WLAN N stick and tried Ubuntu 12.04. Installation went fine and WLAN is working. However, connection drops permanent. Reconnecting manually fixes it but after a few minutes it drops again. It's connected to a Vodafone 802 box with WLAN N fix set. It seems that it works when I switch off N mode. But I need to test. Can someone confirm this issue or is there another solution? I have another machine with 12.04 (HP 625 laptop) running where connection is stable.

    Read the article

  • How to resolve "Network host is busy; will retry in 30 seconds"?

    - by k0pernikus
    I have added a network printer, a Konica Minolta C253, via cups by its IP (http://10.0.0.42) under the http://localhost:631/ cups webfrontend on an Ubuntu 11.10 client. I used the documented KOC353U.ppd in the process. I was able to print exactly one page. Afterwards, all I get in the printer's status is the message: "Network host '10.0.0.42' is busy; will retry in 30 seconds". What is the problem here and how do I resolve it?

    Read the article

  • Quickly and Python Twisted

    - by Aaron
    I am creating a Quickly application that makes use of Python Twisted. When the user launches a window, I want to start the Twisted server I wrote. However, when I do this, it freezes the GUI, because the reactor.run method is constantly running after it is started. I need a way to start the Twisted reactor in its own thread, so that the GUI will continue to operate while the reactor is running. I have read about using Twisted with pyGTK in the Twisted documentation, but I am not sure how I would accomplish this with a Quickly application. What is the best way to start my Twisted server when a window opens without freezing the GUI? Update: My if __name__ == '__main__' statement at the end of my dialog file is: print 'Preparing GLib' GLib.idle_add(before_running) print 'Staring Reactor' from twisted.internet import reactor reactor.run()` I have imported and installed twisted.gtk3reactor earlier on in the file. The before_running method contains dialog = ClientDialog() and dialog.show, as well as the rest of the code I want to run when the dialog opens.

    Read the article

  • Problems with NAT Adapater since upgrade to Ubuntu 12.10

    - by jjesse
    I was running Ubuntu 12.04 w/ VirtualBox installed. I was using the NAT interface to connect to everything. Basically running VBOX for testing some things and a Windows VM for Netflix.. Was back to working in my VMs today and noticed that I was unable to connect to the internet. In the VM settings I'm using the NAT adapter, however I noticed there is no NAT adapter in the Network Settings under Preferences in VBOX. Not quite sure what happened but wonder what is going on? I noticed there are some posts about changes DNSMASQ and configuring a bridge mode, but this worked out of the box under 12.04 and since the upgrade this no longers work. Need some help please

    Read the article

  • IP/PORT forward requests to another server

    - by DT.DTDG
    I have the following listening PORT:IP set up on my UBuntu server. 12.345.67.890:3636 It receives requests perfectly, however, I would now like to forward any requests to that IP:PORT to another IP:PORT, i.e.: 09.876.54.321:3636 Essentially I want to do a request forward 12.345.67.890:3636 -> 09.876.54.321:3636. How can I go about it in Terminal and if I wanted to change it back how can I go about that too? Is there also a way to test that the data is forwarding and it is setup properly? Thanks! Edit: Can I just do as follows, just wondering how I would go about testing it and how I could disable it? sysctl net.ipv4.ip_forward=1 iptables -t nat -A PREROUTING -p tcp --dport 3636 -j DNAT --to-destination 09.876.54.321:3636 iptables -t nat -A POSTROUTING -j MASQUERADE

    Read the article

  • Network setup not working. Can't connect to the Internet in Ubuntu

    - by Clint Eastwood
    I want to know how to set-up network in 12.04 using automatic settings (DHCP). I installed Ubuntu, but I can't seen to see the network connection. What can I do? My notebook has no wireless only cable. The cable will not fit in. How can I plug it in? Do I need a special Cable? There is no router can I fix this myself, or should I call a technician? Also can I use USB to connect to the network/Internet? please can you help Thank you jamel

    Read the article

  • HP mini 5102 Ethernet does not work after suspend on Lubuntu 12.10

    - by Marcin
    Ethernet works fine after system is rebooted The onboard card is seen in 'lspci' as: 43:00.0 Ethernet controller: Marvell Technology Group Ltd. Yukon Optima 88E8059 [PCIe Gigabit Ethernet Controller with AVB] (rev 11) After system being suspended the sky2 driver loads but does not enable the NIC. I have noticed that it happens when PC is left suspended for longer period of time (few houres) Trying to reproduce it I have tried to load the sky2 driver with 'modprobe sky2'. Unfortunately typing 'ifconfig -a' for the onboard ethernet adapter does not list the driver once the sky2 driver is loaded. I have searched internet and I found some information about a bug in kernel. Hovewer it was reported in 2010 so I hope it has been fixed. Here it is http://lists.opensuse.org/opensuse-bugs/2010-02/msg01473.html

    Read the article

  • dhcp configuration not working ubuntu 11.10

    - by Vivek Pradhan
    I am usually behind a proxy server in college so I connect to the ethernet or wifi using manual IPv4 addresses only inside college. I have been trying really hard to get the internet work at home, there is no proxy and I have set the network to use automatic dhcp. It seems like it is not able to connect to the port, It gets disconnected after some time automatically and then tries to reconnect. The same thing is happening with wifi networks also, after some time i see a pop up asking for authentication and ultimately its not able to connect. What might be the problem here. I looked up some similar questions and checked the /etc/network/interfaces file and looks like this: auto lo iface lo inet loopback I have no idea what those lines mean but there is no configuration for eth0 or wlan0. Any help is deeply appreciated. Ubuntu loses it charms due to these small glitches.

    Read the article

  • Uploading or attaching files that located on a shared drive doesn't work?

    - by Alex
    I have this odd, quite minor, but annoying issue that I am quite perplexed about. Whenever I try to upload a file via my browser(let's say attach a file to an email in GMail), I click 'Browse' button and it opens standard file selection dialog, that doesn't show network drives. Further more if I try to drag a file from a network drive into GMail, it doesn't work either, it just doesn't let me do that. This issue has been around for quite sometime now, and I am just curious if this is something on my side or if it's a bug or a misconfiguration of some sort. FWIW, I am currently running 10.10, network drive is a samba share on NAS. This happens in FF and Chrome and this is only happens with Samba mounts. As a matter of fact, NFS volumes that are located on the same network operate perfectly fine.

    Read the article

  • Cannot connect to windows share

    - by BCqrstoO
    I've been going through and pouring over resource for the past few hours and I cannot get my box to connect to my friends network drive. My friend doesn't use linux, but he's setup the network share like this: DPR:\\name\images and he's given me the username and password which I've verified is correct. It is located on 192.168.0.2 sudo mount -t cifs -o username=***,password=*** //name/images /media/name/ sudo mount.cifs //192.168.0.2/name/images /media/name/ -o credentials=~/name.credentials (I've confirmed that ~/name.credentials does have the correct credentials as well) Regardless of what I attempt I get mount error(13): Permission denied Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) I'm not sure what I'm doing wrong, but it's probably really simple and stupid. Thanks to any/all in advance. EDIT: I don't know if this helps, but I'm running Ubuntu 14.04.

    Read the article

  • Cannot use broadband in Kubuntu

    - by Amanz Linux
    I have 5 months of experience using ubuntu 10:10. And it is clear it is suitable for broadband use. For Kubuntu, I have thoroughly tried everything available, using the 10:10 Kubuntu CD that I have had for the last week. It is very appealing, but in the meantime I am unable to use broadband in Kubuntu. I've tried and tried, thinking that it was possible that the use of broadband in Kubuntu was the same as in Ubuntu, so I have attempted to use broadband just as I used it in ubuntu. But I have failed to successfully test the broadband. Kubuntu was much different from ubuntu. Can anyone help me solve this problem?

    Read the article

  • Ubuntu 11.10 is not detecting wired connection on Lenovo G580

    - by Dilip
    I am not able to see wired connection options in header menu. I can see wireless option but still It is not working. Could any one suggest what I am missing? Please find my ifconfig output: =================================== root@rails-dev:/home/rails_work/rdfnet# ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:41944 errors:0 dropped:0 overruns:0 frame:0 TX packets:41944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4602835 (4.6 MB) TX bytes:4602835 (4.6 MB) ===================================

    Read the article

  • Wireless not connecting on Ubuntu 13.10, Toshiba Satellite pro L 650

    - by user204842
    I have just installed Ubuntu 13.10 on my Toshiba Satellite Pro L650. After several reboots, installing/ uninstalling the broadcom driver I still can't connect. It detects the wi fi signals and the icon flashes as if it's trying to connect but never actually does. I'm really quite rubbish with code and stuff, but I really like Ubuntu as an OS and would really appreciate any suggestions anyone can offer! 02:00.0 Ethernet controller: Qualcomm Atheros AR8151 v1.0 Gigabit Ethernet (rev c0) 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01)

    Read the article

  • Network connection fails when downloading data

    - by Guus
    In the past few weeks, I've noticed my network connection becoming unstable while downloading files. I'm not sure how to diagnose this issue. I've found that my network connections appear to be temporarily unresponsive (for periods up to a minute or so) while I'm downloading a file (that's large enough to not be downloaded instantly). The problem occurs when downloading data through a webbrowser, but also when using SCP to download data from a remote location. During the period in which network connections are unresponsive, every resource that I try to access over the network is unavailable. This includes: The download itself (SCP reports a 'stalled' download) Web pages (won't load - browsers report 'resource unavailable') SSH sessions (CLI freezes) VPN connections (connections terminate) IM client connections (client starts reconnection attempts) ... (everything is pretty much dead) I've noticed that during such a period, I cannot even access the (web-based) administrative console of the router on my LAN at home (although it remains reachable for other devices). The problem occurs when connected to my home network, but also when I'm in the office. Other devices than my laptop are not affected. Given the above two characteristics I assume the problem cause lies within my laptop, not the network infrastructure. I'm running Ubuntu 11.10. Apart from applying automatic updates from Ubuntu, I can't think of a change that I applied to the OS that could have started the problems. I'm absolutely positive that this issue did not occur up to a few weeks ago (as it's very noticeable, and only started to annoy me in the last few days). When the problem occurs, applications that make use of a network connection fail visibly (I get popups telling me that a VPN connection is broken, for instance). The network manager does not report any issues related to my wifi-connection though. Help?

    Read the article

  • Best way to cache apt downloads on a LAN?

    - by Ken Simon
    I have multiple Ubuntu machines at home and a pretty slow internet connection, and sometimes multiple machines need to be updated at once (especially during new Ubuntu releases.) Is there a way where only one of my machines needs to download the packages, and the other machines can use the first machine to get the debs? Does it involve setting up my own local mirror? Or a proxy server? Or can it be made simpler?

    Read the article

  • How do i Setup Different Users to Folders

    - by Erin
    I am trying to setup a Ubuntu Server for an office. Its going to be a file share server that 4-5 desktops connect to and access the files. Im planning on having different access for certain computers so computer 1 has full access but say computer 2 can only see a certain folder. My question is, is this possible and how would i go about setting it up? All workstations are using Windows XP - Vista.

    Read the article

< Previous Page | 56 57 58 59 60 61 62 63 64 65 66 67  | Next Page >