Search Results

Search found 15160 results on 607 pages for 'boot disk'.

Page 581/607 | < Previous Page | 577 578 579 580 581 582 583 584 585 586 587 588  | Next Page >

• file corruption on read/write 2.6.32-22-server (happens across many kernels)

  - by Jonathan

  Hi Guys, I'm having an issue where after the server has been up for a period of time (~week/few days) the server will start reading corrupt data. For instance when I run a sha1sum of a file after a fresh boot it remains the same. However after a while I will start to get segfaults and from then on whenever I read this file I get a different sha1sum. I've checked S.M.A.R.T with long tests and I've run an extended memtest86+(12 passes) My lspci is as follows: 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge 00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:07.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 3) 00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3c) 00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller 00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon HD 3300 Graphics 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller 02:00.0 Ethernet controller: Atheros Communications Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller (rev b0) 03:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. Device 3403 I could really use some help on this, do you have any idea what could cause this? It's really frustrating me as it seems to trigger entirely randomly and will not go away until I reboot. I'm also use KVM for virtualization as well as MD for software RAID on this server and the processor is a Phenom II X4 965. I don't believe it's the software raid however as this affects files also hosted on non-raid partitions so I don't know.

  Read the article

• I want to virtualize my workstation (Tier 1), Looking for Bare Metal Hypervisor for consumer grade components

  - by Chase Florell

  I find myself in this similar bind at least once a year. The bind whereby I'm either upgrading a motherboard, or an OS hard drive. It drives me crazy to have to reinstall Windows, Visual Studio, all my addins, reconfigure my settings etc... every single time. I have a layout and I like and I want to stick with it. My question is... Is there a Bare Metal Hypervisor on the market that will enable me to virtualize my consumer grade workstation? I really want to avoid Host/Client virtualization. Bare Metal is definitely a better way to go for my needs. Is this a good approach, or am I going to suffer some other undesirable side effects by doing this? Clarification My machine has very limited purposes. My primary use is Visual Studio 2010 Professional where I develop ASP.NET MVC Web Applications. The second piece of software that I use (that's system intensive) is Photoshop CS3. Beyond that, my applications are limited to Outlook, Internet Explorer, Firefox, Opera, Chrome, LinqPad, and various other (small) apps. Beyond this, I'm considering working on a node.js project and might run ubuntu on the same hypervisor if possible. System Specs: Gigabyte Motherboard Intel i7 920 12 GB Ram basic 500GB 7200RPM HDD for OS 4 VelociRaptors in Raid 1/0 for build disk Dual GTS250 (512MB) Graphics cards (non SLI) for quad monitors On a side note I also wouldn't be opposed to an alternative suggestion if the limitations are too great. I could install the ESXi (or Zen Server) on my box, and build a separate "thin client" to RDP into the virtual machine. It appears as though RDP supports dual monitors. Edit (Dec 9, 2011) It's been nearly a year since I first asked this question. Since then, there have been a lot of great strides in Hypervisor technology... AND MokaFive is now released for corporate use. I'd love to dig into this question a little more and find out if there is a solid BareMetal Hypervisor for workstations running consumer grade components (IE: not Dell, HP, Lenovo, Etc).

  Read the article

• Lots of dropped packages when tcpdumping on busy interface

  - by Frands Hansen

  My challenge I need to do tcpdumping of a lot of data - actually from 2 interfaces left in promiscuous mode that are able to see a lot of traffic. To sum it up Log all traffic in promiscuous mode from 2 interfaces Those interfaces are not assigned an IP address pcap files must be rotated per ~1G When 10 TB of files are stored, start truncating the oldest What I currently do Right now I use tcpdump like this: tcpdump -n -C 1000 -z /data/compress.sh -i any -w /data/livedump/capture.pcap $FILTER The $FILTER contains src/dst filters so that I can use -i any. The reason for this is, that I have two interfaces and I would like to run the dump in a single thread rather than two. compress.sh takes care of assigning tar to another CPU core, compress the data, give it a reasonable filename and move it to an archive location. I cannot specify two interfaces, thus I have chosen to use filters and dump from any interface. Right now, I do not do any housekeeping, but I plan on monitoring disk and when I have 100G left I will start wiping the oldest files - this should be fine. And now; my problem I see dropped packets. This is from a dump that has been running for a few hours and collected roughly 250 gigs of pcap files: 430083369 packets captured 430115470 packets received by filter 32057 packets dropped by kernel <-- This is my concern How can I avoid so many packets being dropped? These things I did already try or look at Changed the value of /proc/sys/net/core/rmem_max and /proc/sys/net/core/rmem_default which did indeed help - actually it took care of just around half of the dropped packets. I have also looked at gulp - the problem with gulp is, that it does not support multiple interfaces in one process and it gets angry if the interface does not have an IP address. Unfortunately, that is a deal breaker in my case. Next problem is, that when the traffic flows though a pipe, I cannot get the automatic rotation going. Getting one huge 10 TB file is not very efficient and I don't have a machine with 10TB+ RAM that I can run wireshark on, so that's out. Do you have any suggestions? Maybe even a better way of doing my traffic dump altogether.

  Read the article

• Event ID 17890 (A significant part... paged out.) with SQL Server 2008

  - by Godeke

  I have a machine that has SQL Server 2008 Standard installed. Periodically (about once an hour) I am getting Event ID 17890 several times in a row. An example: 6:28:54 "A significant part of sql server process memory has been paged out. This may result in a performance degradation. Duration: 0 seconds. Working set (KB): 10652, committed (KB): 628428, memory utilization: 1%%. 6:34:27 "A significant part of sql server process memory has been paged out. This may result in a performance degradation. Duration: 332 seconds. Working set (KB): 169780, committed (KB): 546124, memory utilization: 31%%." 6:38:55 "A significant part of sql server process memory has been paged out. This may result in a performance degradation. Duration: 600 seconds. Working set (KB): 245068, committed (KB): 546124, memory utilization: 44%%." This pattern repeated at 7:26 - 7:37, 8:26 - 8:36, 9:24 - 9:35 and so with the same increasing working set and memory utilization pattern. I don't have any (known) background tasks running at this time. Backups run at 2:00 This subsided from 11:00 at night until it resumed at 4:00 in the morning and has been continuing the intermittent 10 minute glitch periods. As this server has plenty of RAM (the commit charge has peaked at 2,871,564 of 4,194,012 physical) I disabled the paging files after reading several items I dug up searching Google and not finding any of them changing the situation. This pattern I am documented is after removing the paging files, so I'm not even sure where we are paging the SQL process could be going. I also changed the SQL process memory to have a minimum of 500MB and a maximum of 2GB of RAM (as this is a light duty database server serving only a small workgroup). Has anyone encountered this? Prior to disabling the page files this error would cause 5 minutes of disk thrashing that disabled access to the databases, files, IIS webs and so on. Since disabling the page files it just logs strange things, but I'm not seeing a performance drop at least. Any suggestions would be welcome.

  Read the article

• Monitoring tools that can take high rate and high volume?

  - by Jon Watte

  We're using Cacti with RRDTool to monitor and graph about 100,000 counters spread across about 1,000 Linux-based nodes. However, our current setup generally only gives us 5-minute graphs (with some data being minute-based); we often make changes where seeing feedback in "near real time" would be of value. I'd like approximately a week of 5- or 10-second data, a year of 1-minute data, and 5 years of 10-minute data. I have SSD disks and a dual-hexa-core server to spare. I tried setting up a Graphite/carbon/whisper server, and had about 15 nodes pipe to it, but it only has "average" for the retention function when promoting to older buckets. This is almost useless -- I'd like min, max, average, standard deviation, and perhaps "total sum" and "number of samples" or perhaps "95th percentile" available. The developer claims there's a new back-end "in beta" that allows you to write your own function, but this appears to still only do 1:1 retention (when saving older data, you really want the statistics calculated into many streams from a single input. Also, "in beta" seems a little risky for this installation. If I'm wrong about this assumption, I'd be happy to be shown my error! I've heard Zabbix recommended, but it puts data into MySQL or some other SQL database. 100,000 counters on a 5 second interval means 20,000 tps, and while I have an SSD, I don't have an 8-way RAID-6 with battery backup cache, which I think I'd need for that to work out :-) Again, if that's actually something that's not a problem, I'd be happy to be shown the error of my ways. Also, can Zabbix do the single data stream - promote with statistics thing? Finally, Munin claims to have a new 2.0 coming out "in beta" right now, and it boasts custom retention plans. However, again, it's that "in beta" part -- has anyone used that for real, and at scale? How did it perform, if so? I'm almost thinking about using a graphing front-end (such as Graphite) and rolling my own retention backend with a simple layer on top of mmap() and some stats. That wouldn't be particularly hard, and would probably perform very well, letting the kernel figure out the balance between frequency of flushing to disk and process operations. Any other suggestions I should look into? Note: it has to have shown itself able to sustain the kinds of data loads I'm suggesting above; if you can point at the specific implementation you're referencing, so much the better!

  Read the article

• Should use EXT4 or XFS to be able to 'sync'/backup to S3?

  - by Rafa

  It's my first message here, so bear with me... (I have already checked quite a few of the "Related Questions" suggested by the editor) Here's the setup, a brand new dedicated server (8GB RAM, some 140+ GB disk, Raid 1 via HW controller, 15000 RPM) it's a production web server (with MySQL in it, too, not just serving web requests); not a personal desktop computer or similar. Ubuntu Server 64bit 10.04 LTS We have an Amazon EC2+EBS setup with the EBS volume formatted as XFS for easily taking snapshots to S3, via AWS' console. We are now migrating to the dedicated server and I want to be able to backup our data to Amazon's S3. The main reason being the possibility of using the latest snapshot from an EC2 instance in case of hardware failure on the dedicated server. There are two approaches I am thinking of: do a "simple" file-based backup with rsync, dumping the database' and other files, and uploading to amazon via S3 API commands, or to an EC2 instance, or something. do a file-system "freeze" (using XFS) with the usual ebs/ec2 snapshot tool to take part of the file system, take a snapshot, and upload it to Amazon. Here's my question (or series of questions): Can I safely use XFS for the whole system as the main and only format on the dedicated server? If not, is it safe to use EXT4? Or should I use something else? would then be possible to make snapshots of the system to upload to Amazon? Is it possible/feasible/practical to do what I want to do, anyway? any recommendations? When searching around for S3/EBS/XFS, anything relevant to my problem is usually focused on taking snapshots of a XFS system that is already an EBS volume. My intention is to do it in a "real"/metal dedicated server. Update: I just saw this on Wikipedia: XFS does not provide direct support for snapshots, as it expects the snapshot process to be implemented by the volume manager. I had always assumed that I could choose 2 ways of doing snapshots: via LVM or via XFS (without LVM). After reading this, I realize these 2 options are more like it: With XFS: 1) do xfs_freeze; 2) copy the frozen files via, eg, rsync; 3) unfreeze xfs With LVM and XFS: 1) do xfs_freeze; 2) make a binary copy of the frozen fs via lvcreate and related commands; 3) unfreeze xfs; 4) somehow backup the LVM snapshot. Thanks a lot in advance, Let me know if I need to clarify something.

  Read the article

• All internet requests in Windows time out

  - by Brandon

  So, I've run into a very strange problem with my home wireless network. Previously, at seemingly random times, the router seemed to disconnect all wireless hosts and cause all of the wired hosts to have a "limited connection" according to windows. In order to fix this, I had to unplug all of the wired hosts from the router, unplug the modem from the router, and power cycle the router. This seemed to solve the problem for a while until the exact same thing happened a day later and I had to go through the same process again. That's where I noticed something weird happening. There was one wireless host (a Windows Vista laptop) that seemed to be causing the router to disconnect the other hosts whenever it connected. When this happened, only that laptop was able to use the wireless from the router. When this happened, I disconnected it from the wireless (by disabling the wireless adapter) then reconnected it (by re-enabling it) and now it, like the other hosts, couldn't connect. I've never really seen anything this strange happen on our network before. So, I restored the router to factory settings and the problem seems to have vanished except one crucial problem. There's another host (a Windows 7 laptop) that was perfectly able to connect before all of the router issues and even in between the crashing and power-cycling events but now says its connected and says it's able to reach the Internet, but all requests time out. In any browser I've tried, the tab says connecting to [site]... for a solid minute and then tells me the request timed out. When I try to ping google.com in cmd it also says request timed out. In frustration, I booted into a dual-boot Ubuntu installation on the Windows 7 host and the connection works fine, to my surprise, as ubuntu is where I am now typing this rather long question. I haven't looked through the event log in windows but will post anything I find in an edit I haven't tried connecting (in Windows 7) to any other wireless network, since The fact that it works in Ubuntu suggests its Windows and not the router but I didn't change any wireless settings in windows before it being able to reach the Internet and not. Does anyone have any clue what could have happened. I opened to buying another router as this one is almost a year old :) but I would like to know whats going on here. Thanks in Advance! P.S. Sorry for how long my question is, I'm a little anxious (:

  Read the article

• Primary/secondary ethernet interfaces via NetworkManager in Ubuntu 9.10

  - by Josh

  I have an Ubuntu 9.10 machine with three ethernet interfaces, eth0, eth1 and eth2. eth2 is connected to a private network. eth0 and eth2 are connected to two different LANs. Either one will provide access to the internet. All three networks have DHCP servers. Using Ubuntu's the default settings (And Gnome), when I boot up all the interfaces are active and my system gets three IP addresses. However any attempt to access the internet results in connection timeouts and other weirdness. I suspect that traffic is going out on one NIC (like eth0) and coming back in on another (like eth1). I'm not sure what's going on. The only way I can access the internet at the moment is to bring two of the devices down with ifdown. How can I configure eth0 as my primary interface so all trafic goes out by default on that interface, while keeping the other two active? Also, I want to make sure Avahi broadcasts properly on all three IPs so that the computers on the LAN of eth1 can still connect to myHostname.local... EDIT: Here's my routing table: Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 172.16.151.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 172.16.30.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.1.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 0.0.0.0 172.16.30.2 0.0.0.0 UG 0 0 0 eth0 0.0.0.0 10.1.0.1 0.0.0.0 UG 0 0 0 eth1 I want the 172.16.30.2 network to be the primary one and the 10.1.0.0 network to be the secondary one. EDIT2: My nameservers are also incorrect. It seems like Ubuntu is bringing the networks up in order, eth0, then 1, then 2, and the DHCP information from eth1 is overriding eth0, and eth2 is overriding eth1. How can I reverse this so the DHCP information from eth0 is the "master"? EDIT3: This seems to be an issue with Gnome's NetworkManager.

  Read the article

• Why Does My Windows 7 PC Freeze After Waking from Sleep?

  - by Blaenk

  Hey guys. I have Windows 7 running on my computer and everything is perfect. There's only one little problem. Sometimes when I leave my computer, I come back and my monitor is turned off or asleep, whichever it is. This is fine, I set it to do this. However, after turning on the monitor and moving the mouse around, the mouse cursor freezes; both the keyboard and mouse don't respond to anything, for example the keyboard's windows key won't bring up the start menu and moving the mouse around does not move the cursor around on the screen. I have to wait about a minute or two before things start working again. I figured this was a power savings setting problem, so I went into Control Panel Power Options. I only have Turn off Display = 30 minutes and Put Computer to Sleep = Never. Of course, I went into the advanced power settings to look through there. I put Never to turn off the hard disk, Sleep after never, and that's about it. Nothing else there looks like it might be causing this. I went into the device manager and checked the mouse and the keyboard, and they both have the Allow this device to wake the computer checked for both of them. Perhaps this other bit of information might help: Sometimes I VNC into my PC using my MacBook, and sometimes, as soon as it shows me the desktop, the same thing happens. The mouse won't move and VNC won't register any events on the server (Which is my PC of course). I close the client (And I know it has nothing to do with the client), then immediately restart it and try to connect. When I click the connect button, it hangs there, as if the PC is not responding. Basically it's like whenever I try to wake the computer from sleep, it does so by showing me the desktop, then it freaks out. Then again, I guess the computer isn't sleeping because the setting is set to 'Sleep after = Never'. I honestly don't know what's going on, would appreciate any insight. Thanks!

  Read the article

• Which hardware to VM ratio for Build-Server virtualization?

  - by Martin

  Let's start with saying that I'm a total noob wrt. to server virtualization. That is, I use VMs often during development, but they're simple desktop machine things for me. Now to my problem: We have two (physical) build servers, one master, one slave running Jenkins to do daily tasks and build (Visual C++ Builds) our release packages for our software. As such these machines are critical to our company, because we do lot's releases and without a controlled environment to create them, we can't ship fixes. (And currently there's no proper backup of these machines in place, because they do not hold any data as such - it just would be a major pain to setup them again should they go bust. (But setting up backup that I'd know would work in case of HW failure would even be more pain, so we have skipped that until now.)) Therefore (and for scaling purposes) we would like to go virtual with these machines. Outsourcing to the cloud is not an option, not at all, so we'll have to use on-premises hardware and VM hosts. Each Build-Server (master or slave) is a fully configured (installs, licenses, shares in case of the master, ...) Windows Server box. I would now ideally like to just convert the (two) existing physical nodes to VM images and run them. Later add more VM slave instances as clones of the existing ones. And here begin my questions: Should I go for one VM per one hardware-box or should I go for something where a single hardware runs multiple VMs? That would mean a single point of failure hardware wise and doesn't seem like a good idea ... or?? Since we're doing C++ compilation with Visual Studio, I assume that during a build the hardware (processor cores + disk) will be fully utilized, so going with more than one build-node per hardware doesn't seem to make much sense?? Wrt. to hardware options, does it make any difference which VM software we use (VMWare, MS, Virtualbox, ... ?) (We're using Windows exclusively for our builds.) Regarding budget: We have a normal small company (20 developers) budget for this. ;-) That is, if it's going to cost a few k$ it's going to cost. If it's free - the better. I strongly prefer solutions where there's no multi-k$ maintenance costs per year.

  Read the article

• Alienware m15x (older model) BSOD investigation

  - by Crishu

  A frined of mine asked me to help him with an Alienware m15x laptop that had a little service history. It was bought in june 2008, serviced in january 2009 for a random fps drop problem, Alienware returned it saying nothing was wrong. The laptop still had hiccups, but after juggling a few drivers and settings, the fps drops weren't as noticeable. Eventually it died in Sept. 2009. It would not boot up locking itself on a white/gray screen. (i think it was overheating .. clocking in 100 degrees Celsius). So back to Alienware it went. They replaced the GPU and all was fine. Up until these blue screens started showing up. One other thing that was updated was the HDD and a Windows 7 reinstall, in August. From then on it seems to have started its BSOD. Could this be the culprit? Why? 0_o The original Windows was Vista but it was upgraded with a digital download/purchase of Windows 7 Home Premium and activated after installing windows. No errors on the old HDD, just on the latest installation. LE:Due note that now the old HDD is used to see if issues re-occur. So please, I am in need of someone who can interpret these windows dump files: Minidump I may have come to some conflicting conclusions. So if someone can clarify each dump/date and the probable cause/error it had; and a final conclusion or solution, we would be very grateful. Also please consult report for other system info I omitted: same link,code: XRWIVLWG If I missed something or if you have any other questions I'll be happy to answer them. Thank you. Good day. Processor: Intel(R) Core(TM)2 Duo CPU T9300 @ 2.50GHz Network Adapter Properties: Broadcom NetLink (TM) Gigabit Ethernet Intel(R) Wireless WiFi Link 4965AGN Video Adapter Properties: Driver Description NVIDIA GeForce 8800M GTX Driver Date 19.08.2009 Driver Version 8.16.11.8681 Driver Provider NVIDIA INF File oem19.inf Hardware ID PCI\VEN_10DE&DEV_060C&SUBSYS_0770152D&REV_A2 Location Information @system32\DRIVERS\pci.sys,#65536;PCI bus %1, device %2, function %3;(1,0,0) PCI Device NVIDIA GeForce 8800M GTX [NoDB] BIOS String Version 62.92.34.0.8 Installed Drivers nvd3dum (8.16.11.8681), nvwgf2um, nvwgf2um Hard Dik Drive: Model ID ST9120823ASG (**older one 120gb**) Model ID WD32000BEKT (new 320gb with fresh OS)

  Read the article

• How to remove RAID flag on unstriped drive without losing data?

  - by Alex Folland

  I have a Gigabyte Z68X-UD4-B3 motherboard. It advertises this new thing called "XHD", which is like RAID but makes a SSD and traditional-style drive work together to enable high speed with high capacity. I don't want to use this feature, and I already have Windows 7 64 installed without using this feature. When I first installed my 2 hard drives (1 SSD and 1 traditional-style drive) in my machine and booted it up for the first time, it ran a program from the mobo that asked me if I wanted to set up XHD. Thinking it would go to some config screen, I said yes. It immediately started doing something with my drives and finished. I considered that strange, but figured it wouldn't matter when I simply install Windows onto my SSD only. I now have my BIOS and Windows running in AHCI mode with no RAID arrays and separate drives. My SSD is one of those new Corsair Force GT drives which loses power every so often, causing Windows to BSOD. I've figured everything out about this problem, including installing the latest firmware from Corsair, and the only way to fix it at this point is by installing Intel Rapid Storage Technology to control AHCI instead of Windows, since the Windows AHCI driver disables the drive's power every once in a while and can't be configured not to do so. I've tried installing Intel Rapid Storage Technology. When I reboot my machine after doing so, it BSODs just after the Windows logo. I've figured out this is because my SSD and my traditional drive are flagged as RAID, as seen in the "Intel Matrix Storage Manager" program found by switching the BIOS hard drive handling to "RAID" mode. This is due to the XHD auto-config program I mentioned earlier. Normally, the BIOS is set to AHCI, and when the drives boot in AHCI mode, they work perfectly. So, I've concluded the data is stored in AHCI mode but the drives' flags are set to RAID. I've figured out that I can accomplish my objective by using the "Intel Matrix Storage Manager" program on the mobo (with "Reset disks to non-RAID"), but doing so would cause it to completely wipe the drives I select. I want to simply toggle these flags from RAID to AHCI so Intel Rapid Storage Technology doesn't fail and cause a BSOD upon booting, but without wiping the drives.

  Read the article

• Win-XP Browsers Hang on page load - (waiting for...)

  - by CHarmon

  Hello, I’m having problems with my browsers hanging on loading pages on my desktop machine. I’m using Windows XP Pro with SP3 and fully updated except for IE 8. All three of my browsers, IE 7, Chrome and Firefox are having the same problems. Pages are not being loaded and are hanging on “waiting for …”. The browsers are waiting for the page being loaded or ad servers. Sometimes a page will load but the loading graphic continues to be displayed as if the page were still loading when the page appears to be fully loaded. The problem is bad enough that I can’t really use any of my browsers. I can eventually get most pages to load by stopping and restarting the page load. I have DSL modem with a wireless router and I have been able to eliminate the modem and router from being the source of my problem. My laptop doesn’t have any problems even when hardwired to the router and with the wireless connection disabled. I deleted the NIC and let XP re-install. Also tried a different network cable. Tried the same router port used in the laptop test. One clue that may be important is that I can’t connect to my router using the desktop machine…the page hangs while trying to connect. I can ping the router and I can quickly connect to the router using the laptop. I also can’t use the Windows update process – the page never fully loads. The problem affects other user accounts and even happens in safe mode. I am convinced the problem is with part of the O/S…some layer able to affect all of the browsers. The purpose of this post is to see if anyone has some ideas before I do a XP repair. I have done quite a bit of trouble-shooting: Ran a full anti-virus scan with AVG – no problems. Ran full scans with Spybot, MalwareBytes and Sophos anti-rootkit – no problems. Ran Chkdsk with both options checked. Ran Disk Clean up Defragged RE-installed IE7 Cleared all the browser caches Ran Ccleaner (registry tool) Ran HijackThis – nothing unusual (problem happens in safe mode too) Ran Process Explorer – no unusual processes Used System Restore and fell back several days – no change in the problem Booted to last known good configuration – no change in the problem Ran MicrosoftFixit50199.msi – no change in the problem Any ideas or suggestions would be appreciated…I’m not looking forward to doing a repair on XP. Thanks in advance for any help.

  Read the article

• Can this USB3 behaviour be anything else than a hardware failure?

  - by Jonas Wielicki

  While my motherboard is half a year old now (ASUS M5A99X EVO), I only recently made use of the USB3 boards (after purchase of USB3 external harddrive). However, I am encountering issues. I am running linux 3.6.7-4.fc16.x86_64. Initially, the harddrive worked fine with USB3 (amazing ˜160MB/s), but I had some problems after putting after putting the harddrive to sleep manually after use (backup) with hdparm -Y. After some time, the device disappears from lsusb and i see the following in dmesg: [ 1924.091107] xhci_hcd 0000:05:00.0: xHCI host not responding to stop endpoint command. [ 1924.091114] xhci_hcd 0000:05:00.0: Assuming host is dying, halting host. [ 1924.091147] xhci_hcd 0000:05:00.0: HC died; cleaning up [ 1924.091233] usb 11-1: USB disconnect, device number 2 [ 1924.091272] sd 6:0:0:0: Device offlined - not ready after error recovery Testing with my (USB3 capable) notebook, I could not immediately reproduce the behaivour. I put the drive to sleep with hdparm -Y and waited for like an hour, but it was still listed in lsusb and responded after a few seconds delay when I tried after the hour of waiting. After an hour, on the desktop, the device would've usually vanished. Googling for this issue, I came across hints that playing around with IOMMU settings and upgrading the BIOS might help. I upgraded the BIOS and tried both with and without IOMMU enabled, got similar results. Most disturbing is, that one of the two USB 3.0 hubs sometimes also disappears from lsusb (or does not show up after boot at all). I've also heard that there are some hardware issues with ASUS USB3 ports. Applying mechanic force to the capble doesn't push the issue to one side or the other. Also, udev seems to reenumerate all devices if I plug the HDD into the USB 3.0 port without success (I can notice from my keyboard layout being changed to the default, which I do not use normally). The drive is externally powered and the external power supply is plugged in (it also stays powered when unplugging from USB, although it will spin down then). So before I try to return the board, I wanted to find out whether this can be anything else than a failure on the motherboard?

  Read the article

• How do you backup 40+ Centos5.5 servers?

  - by John Little

  We are embarrassed to ask this question. Apologies for our lack of UNIX expertise. We have inherited 40+ centos 5.5 servers, and don't know how to back them up. We need low level clone type images so that we could restore the servers from scratch if we had to replace the HDs etc. We have used the "dd" command, but we assume this only works if you want to back up one local disk to another, not 40 servers to one server with an external USB HD attached. All 40 servers have a pair of mirrored disks (dont know if its HW or SW raid). Most only have 100MB used. SErvers are running apache, zend, tomcat, mysql etc. Ideally we dont want to have to shut them down to backup (but could). We assume that standard unix commands like tar, cpio, rsync, scp etc. are of no use as they only copy files, not partitions, all attributes, groups etc. i.e. do not produce a result which can simply be re-imaged to a new HD to get the serer back from dead. We have a large SAN, a spare windows box and spare unix boxes, but these are only visible to one layer in the network. We have an unused Dell DL2000 monster tape unit, but no sw or documentation for it. WE have a copy of symantec backup exec, but we have no budget for unix client licenses. (The company has negative amounts of money). We need to be able to initiate the backup remotely, as we can only access the servers in person in an emergency (i.e. to restore) Googling returns some applications to do this, e.g. clonezilla - looks difficult to install and invasive. Mondo, only seems to support backup if you are local to the machine. Amanda might be an option, but looks like days/weeks of work to learn and setup? Is there anything built into Centos, or do we have to go the route of installing, learning and configuring a set of backup softwares? Any ideas? This must be a pretty standard problem which goggling doesnt give an obvious answer.

  Read the article

• SSH Connection Refused - Debug using Recovery Console

  - by olrehm

  Hey everyone, I have found a ton of questions answered about debugging why one cannot connect via SSH, but they all seem to require that you can still access the system - or say that without that nothing can be done. In my case, I cannot access the system directly, but I do have access to the filesystem using a recovery console. So this is the situation: My provider made some kernel update today and in the process also rebooted my server. For some reason, I cannot connect via SSH anymore, but instead get a ssh: connect to host mydomain.de port 22: Connection refused I do not know whether sshd is just not running, or whether something (e.g. iptables) blocks my ssh connection attempts. I looked at the logfiles, none of the files in /var/log contain any mentioning on ssh, and /var/log/auth.log is empty. Before the kernel update, I could log in just fine and used certificates so that I would not need a password everytime I connect from my local machine. What I tried so far: I looked in /etc/rc*.d/ for a link to the /etc/init.d/ssh script and found none. So I am expecting that sshd is not started properly on boot. Since I cannot run any programs in my system, I cannot use update-rc to change this. I tried to make a link manually using ln -s /etc/init.d/ssh /etc/rc6.d/K09sshd and restarted the server - this did not fix the problem. I do not know wether it is at all possible to do it like this and whether it is correct to create it in rc6.d and whether the K09 is correct. I just copied that from apache. I also tried to change my /etc/iptables.rules file to allow everything: # Generated by iptables-save v1.4.0 on Thu Dec 10 18:05:32 2009 *mangle :PREROUTING ACCEPT [7468813:1758703692] :INPUT ACCEPT [7468810:1758703548] :FORWARD ACCEPT [3:144] :OUTPUT ACCEPT [7935930:3682829426] :POSTROUTING ACCEPT [7935933:3682829570] COMMIT # Completed on Thu Dec 10 18:05:32 2009 # Generated by iptables-save v1.4.0 on Thu Dec 10 18:05:32 2009 *filter :INPUT ACCEPT [7339662:1665166559] :FORWARD ACCEPT [3:144] :OUTPUT ACCEPT [7935930:3682829426] -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m tcp --dport 25 -j ACCEPT -A INPUT -p tcp -m tcp --dport 993 -j ACCEPT -A INPUT -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT -p tcp -m tcp --dport 143 -j ACCEPT -A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 8080 -s localhost -j ACCEPT -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 -A INPUT -j ACCEPT -A FORWARD -j ACCEPT -A OUTPUT -j ACCEPT COMMIT # Completed on Thu Dec 10 18:05:32 2009 # Generated by iptables-save v1.4.0 on Thu Dec 10 18:05:32 2009 *nat :PREROUTING ACCEPT [101662:5379853] :POSTROUTING ACCEPT [393275:25394346] :OUTPUT ACCEPT [393273:25394250] COMMIT # Completed on Thu Dec 10 18:05:32 2009 I am not sure this is done correctly or has any effect at all. I also did not find any mentioning of iptables in any file in /var/log. So what else can I do? Thank you for your help.

  Read the article

• How to store data on a machine whose power gets cut at random

  - by Sevas

  I have a virtual machine (Debian) running on a physical machine host. The virtual machine acts as a buffer for data that it frequently receives over the local network (the period for this data is 0.5s, so a fairly high throughput). Any data received is stored on the virtual machine and repeatedly forwarded to an external server over UDP. Once the external server acknowledges (over UDP) that it has received a data packet, the original data is deleted from the virtual machine and not sent to the external server again. The internet connection that connects the VM and the external server is unreliable, meaning it could be down for days at a time. The physical machine that hosts the VM gets its power cut several times per day at random. There is no way to tell when this is about to happen and it is not possible to add a UPS, a battery, or a similar solution to the system. Originally, the data was stored on a file-based HSQLDB database on the virtual machine. However, the frequent power cuts eventually cause the database script file to become corrupted (not at the file system level, i.e. it is readable, but HSQLDB can't make sense of it), which leads to my question: How should data be stored in an environment where power cuts can and do happen frequently? One option I can think of is using flat files, saving each packet of data as a file on the file system. This way if a file is corrupted due to loss of power, it can be ignored and the rest of the data remains intact. This poses a few issues however, mainly related to the amount of data likely being stored on the virtual machine. At 0.5s between each piece of data, 1,728,000 files will be generated in 10 days. This at least means using a file system with an increased number of inodes to store this data (the current file system setup ran out of inodes at ~250,000 messages and 30% disk space used). Also, it is hard (not impossible) to manage. Are there any other options? Are there database engines that run on Debian that would not get corrupted by power cuts? Also, what file system should be used for this? ext3 is what is used at the moment. The software that runs on the virtual machine is written using Java 6, so hopefully the solution would not be incompatible.

  Read the article

• What are the most likely bottlenecks determining the performance of CamStudio screen recording?

  - by Steve314

  When doing screen recording, I can get a frame rate of maybe 15 frames per second for the full screen on my 1080p monitor using the XVID codec. I can increase the speed a bit by recording a region, changing screen modes, and tweaking other settings, but I'm curious what hardware upgrades might give me the biggest bang for my buck. My PC is budget, but modern... Athlon 2 X4 645 (3.1GHz, quad core, limited cache) processor. 4GB single channel DDR3 1066 RAM. ASRock motherboard with NVidia GeForce 7025/nForce 630a Chipset. ATI Radeon HD 5450 graphics card - 512MB on board, not configured to steal system RAM. I dual-boot Windows XP and Windows 7. For the moment, XP is my bigger performance concern as it's still my getting-things-done O/S as opposed to my browser-host O/S. My goal is to make a few programming-related tutorials. For a lot of that I don't need screen recording - I can make up some slides, record audio with the PC switched off, yada yada. When I do need screen recording, I'll mostly be recording Notepad++, Visual Studio or a command prompt. Occasionally, I may be recording some kind of graphics or diagram program and using my pre-Bamboo cheap Wacom tablet - I have the CS2 versions of Photoshop and Illustrator, but I'd much more likely be using Microsoft Paint. Basically, what I'll be recording won't be making huge demands on the machine - but recording a fair number of pixels (720p preferred) will be useful. What's particularly wierd - not so long ago I still had a five-year-old Pentium 4 based PC. And (with the same 1080p monitor) it could record at not far from the same frame rate. So clearly the performance issues are more subtle than just throw-money-at-it. My first guess would be that the main bottleneck is the bandwidth for transferring data to/from the graphics card. Is that likely to be correct? In support of that, see this [Radeon HD 5450 review][1] - the memory bandwidth is only 12.8 GB/s. If you can't get data out of graphics memory quickly, you can't transfer it back to the system memory quickly. Apparently, that's slower than some top-end cards in 2002.

  Read the article

• Triple monitor setup in linux

  - by Brendan Abel

  I'm hoping there are some xorg gurus out there. I'm trying to get a three monitor setup working in linux. I have 2 lcd monitors and a tv, all different resolutions. I'm using 2 video cards; a 9800 GTX and 7900Gt. I've seen a lot of different posts about people trying to make this work, and in every case, they either gave up, or Xinerama magically solved all their problems. Basically, my main problem is that I cannot get Xinerama to work. Every time I turn it on in the options, my machine gets stuck in a neverending boot cycle. If I disable Xinerama, I just have three Xorg screens, but I can't drag windows from one to the other. I can get the 2 lcds on Twinview, and the tv on a separate Xorg screen no problem. But I don't really like this solution. I'd rather have them all on separate screens and stitch them together with Xinerama. Has anyone done this? Here's my xorg.conf for reference. p.s. This took me all of 30 seconds to set up in Windows XP! p.s.s. I've seen somewhere that maybe randr can solve my problems? But I'm not quite sure how? Section "Monitor" Identifier "Main1" VendorName "Acer" ModelName "H233H" HorizSync 40-70 VertRefresh 60 Option "dpms" EndSection #Section "Monitor" # Identifier "Main2" # VendorName "Acer" # ModelName "AL2216W" # HorizSync 40-70 # VertRefresh 60 # Option "dpms" #EndSection Section "Monitor" Identifier "Projector" VendorName "BenQ" ModelName "W500" HorizSync 44.955-45 VertRefresh 59.94-60 Option "dpms" EndSection Section "Device" Identifier "Card1" Driver "nvidia" VendorName "nvidia" BusID "PCI:5:0:0" BoardName "nVidia Corporation G92 [GeForce 9800 GTX+]" Option "ConnectedMonitor" "DFP,DFP" Option "NvAGP" "0" Option "NoLogo" "True" #Option "TVStandard" "HD720p" EndSection Section "Device" Identifier "Card2" Driver "nvidia" VendorName "nvidia" BusID "PCI:4:0:0" BoardName "nVidia Corporation G71 [GeForce 7900 GT/GTO]" Option "NvAGP" "0" Option "NoLogo" "True" Option "TVStandard" "HD720p" EndSection Section "Module" Load "glx" EndSection Section "Screen" Identifier "ScreenMain-0" Device "Card1-0" Monitor "Main1" DefaultDepth 24 Option "Twinview" Option "TwinViewOrientation" "RightOf" Option "MetaModes" "DFP-0: 1920x1080; DFP-1: 1680x1050" Option "HorizSync" "DFP-0: 40-70; DFP-1: 40-70" Option "VertRefresh" "DFP-0: 60; DFP-1: 60" #SubSection "Display" # Depth 24 # Virtual 4880 1080 #EndSubSection EndSection Section "Screen" Identifier "ScreenProjector" Device "Card2" Monitor "Projector" DefaultDepth 24 Option "MetaModes" "TV-0: 1280x720" Option "HorizSync" "TV-0: 44.955-45" Option "VertRefresh" "TV-0: 59.94-60" EndSection Section "ServerLayout" Identifier "BothTwinView" Screen "ScreenMain-0" Screen "ScreenProjector" LeftOf "ScreenMain-0" #Option "Xinerama" "on" # most important option let you window expand to three monitors EndSection

  Read the article

• Linux Best Practices

  - by Zac

  I'm a life-long Windows developer switching over to Linux for the first time, and I'm starting off with Ubuntu to ease the learning curve. My new laptop will primarily be a development machine: 6GB RAM, 320 GB HD. I'd like there to be 2 non-root users: (a) Development, which will always be me, and (b) Guest, for anyone else. I assume the root user is added by default, like System Administrator in Windows. (1) I'd like to mount /home to its own partition, but how does this work if I have two user accounts (Development and Guest)? Are there 2 separate /home directories, or do they get shared? Is it possible to allocate more space for Development and only a tiny bit of space for Guest in GRUB2? How?!?! (2) I'm assuming that its okay that all of my development tools (Eclipse & plugins, SVN, JUnit, ant, etc.) and Java will end up getting installed in non-/home directories such as /usr and /opt, but that my Eclipse/SVN workspace will live under my /home directory on a separate partition... any problems, issues, concerns with that? (3) As far as partitioning schemes, nothing too complicated, but not plain Jane either: Boot Partition, 512 MB, in case I want to install other OSes Ubuntu & non-/home file system, 187.5 GB Swap Partition, 12 GB = RAM x 2 /home Partition, 120 GB I don't have any bulky media data (I don't have music or video libraries, this is a lean and mean dev machine) so having 320 GB is like winning the lottery and not knowing what to do with all this space. I figured I'd give a little extra space to the OS/FS partition since I'll be running JEE containers locally and doing a lot of file IO, logging and other memory-instensive operations. Any issues, problems, concerns, suggestions? (4) I was thinking about using ext4; seems to have good filestamping without any space ceiling for me to hit. Any other suggestions for a dev machine? (5) I read somewhere that you need to be careful when you install software as the root user, but I can't remember why. What general caveats do I need to be aware of when doing things (installing packages, making system configurations, etc.) as root vs "Development" user? Thanks!

  Read the article

• Recovering data from failed Raid configuration with 4 drives and two raid sets (Asus P6T / Intel ICH10r)

  - by user56365

  I've added the complete detailed version for my question below for those who can help, but want to quickly summarize my question first. I setup two Raid arrays using (4) WD Raptors, a striped set for the OS and 1+0 set for crucial data. After booting once out of the 50 times a cable fell out, the drive wasn't recognized in the array anymore. After trying to fix it, another drive did the same. I now have two drives remaining, luckily with the parity information. I know the striped set is gone, but I need the data on the other set. Can anyone recommend anything to recover the data, or fix the two drives that doesn't allow the raid controller to recognize the drives, even though they are listed on the utility screen as still apart of the configuration but that they are not found? More Details I recently upgraded to a ASUS P6T motherboard with an Intel ICH10R raid controller and changed my previous 4 drive raid array from strictly a Raid 1+0 set to a Raid 0 for the OS/Page/Scratch drive and a Raid 1+0 set for crucial data. I never had problems after upgrading with my configuration, even when a drive died and was replaced. I managed to rebuild the array fine. Unfortunately this time around, a cable came unattached and I booted my system up until the raid status screen with the degraded error. This shouldn't have been a problem, but after I attached the drive it was no longer recognized as a member in the array. Both drives actually show up as a non-member disk. I've spent a very, very long time online trying to find information or support and haven't had much luck. After spending time trying to scan the drive for errors, damaged partition info, etc.. another drive in the set decided it didn't want to be recognized as a part of the array. At this point, I have two out of the four drives still functioning, but the Raid 1+0 array went from degraded to failed and I must find a way to retrieve that data. I think the two drives still in the array have the parity information because they show up as OS (110GB),BACKUP(80GB) and OS:1(110GB),BACKUP(80GB) under windows data management. The other two are simply 74gb Raw unallocated Is it possible recover the data using those two drive only, and which tool would I use? Could it be a simple partition table or any other error that is repairable with hard drive utilities out there? I know the Raid 0 set is done for, but I would assume because the correct drives failed in a 1+0 config to save the data I can retrieve it some how.

  Read the article

• Network Services disabled (not starting) on Windows XP

  - by Rickesh John

  I am currently running Windows XP Service Pack 3 on my system. But today, when I failed to connect to the internet, via a LAN cable, I realized that almost all of the vital network services had stopped functioning. Any attempts to start it through services.msc gives me the following message: Could not start the DNS Client Service on Local Computer Error 1068: The dependency service group failed to start All my software or services that are related to networking have stopped functioning, for example, Windows Firewall is turned off permanently, so is my Avast Anti-Virus' service of Real Time Shields and Web Shield. When I insert the LAN wire into my laptop, it registers itself, but this is what I get when I do a ping localhost C:>ping localhost Unable to contact IP driver, error code 2 Moveover, with ipconfig I get this : Windows IP Configuration An internal error occurred: The request is not supported. Please contact Microsoft Product Support Services for further help. Additional Information: Unable to query host name On some further poking around, I saw that none of the "NETWORK SERVICE" process in task manager, except svchost.exe were running. Also, when I first opened the task manager, I saw some 20 processes running with username column empty for most of them. With some search in Google, I found out that these services were important, DHCP DNS Net logon Network connection Network location Awareness TCP/IP Net BIOS Helper none of them, except Network Connections are working, they do not start. The event viewer of my system shows a bunch of 7000 and 7001 event errors. I have tried re installing the network driver, booting in safe mode with networking and tried to enable those services mentioned above. I had disabled System Restore some time back, so I have no restore points for my system. I tried a lot of things from Google searches but none of them worked. Also, with such a long list of issue, I am a little confused as to what should I search on the internet. :( One more thing I would like to mention, previous morning, my anti-virus Avast detected a RootKit buried deep in my system folders. It was removed, but maybe this was a problem caused by the root kit. I did run a boot-time scan but no viruses were found. Please please please advice. Is formatting and re-installation of Windows my only option?

  Read the article

• Logitech Optical Mouse Frozen In Middle of Windows XP Pro Screen

  - by Code Sherpa

  Hi. I have a Logitech Optical Mouse/Keyboard. I have been using them just fine with the system drivers for almost a year now. I recently updated my Kaspersky software and rebooted. Now the mouse is frozen in the middle of my screen. I am not able to login to the Windows XP Pro box that has the frozen mouse (because i can't work the mouse) but am able to remote desktop to this computer. Things I know / have tried: When I boot on the problem computer, I am able to use the keyboard, but not the mouse. I have installed the latest version of Logitech's SetPoint (with the updated drivers) on the problem computer (via remote desktop) and that didn't seem to matter. I bought new batteries for the mouse and that didn't matter. I have tried the mouse/keyboard on another computer and the mouse works just fine there. My suspicion is that the Kaspersky install has overwritten a driver of some sort. Things I have not done (and would appreciate detailed steps if you feel this is the way to go): 1) Uninstalled all the mouse drivers on the machine and reboot. Then, reinstall. Note: When I get to the Device Manager I don't see an option for Human Interface Devices (where the mouse device is). Here are my options: Computer, Disk Drives, DVD/CD-Rom drives, Floppy controllers, IDE ATA/ATAPI, Imaging devices, Network Adapters, Other devices, Ports, Processors, Sound, video, and gaming, System devices, USB controllers. Also, I should point out that Video Controller is the only thing under Other devices and it has a yellow exclamation mark. The same is true for all the items under Universal Serial Bus controllers. I think this means I have to update my BIOS but, since my mouse was working just fine without doing that, I don't think that is my problem. So, how do I get to my Mouse Device? 2) Update my BIOS. Note: As pointed out above, I don't think this matters as my mouse was working just fine under my computer's current BIOS version. Thanks for your help.

  Read the article

• My VPS ubuntu server is very slow

  - by askmike

  I just installed a frech copy of Ubuntu 12.04 on my vps because my old installation was very slow, unfortunately this did not fix the problem. With slow I mean requests for my PHP websites take a long time, very slow (30 sec per request) to slow (3+ sec per request). When it's really bad SSH is also laggish. The websites are: askmike.org (pretty standard Wordpress) mvr.me (own PHP) slow? very slow: Here is a picture of loading a clean install of wordpress slow: here is a picture of loading a small PHP based website the vps The VPS has 256mb ram and an 25GB hdd. Besides serving the 2 small websites it isn't doing anything AFAIK. What have I installed Clean Ubuntu server 12.04 LAMP stack few things like git and nodejs (not using both) ossec (because I thought my server was getting hammered) munin What I already tried / done I installed munin so that I could watch io speed and such. The problem is that I don't know where to look for in the munin report. I checked logs and don't see anything strange (although I don't really know where to look for besides strange / repetitive errors and GET requests). I configured Apache MPM to: <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 5 MaxSpareServers 10 MaxClients 40 MaxRequestsPerChild 0 </IfModule> (apache is using prefork, the default) Stats I copied the munin report as it appeared at 4:50 last night to a site hosted on a shared webhost. Note that tonight my mysql crashed somewhere after 1:00 (which is a new problem altogether), so therefor the graph for last night might look strange. Can anyone help me get my VPS up to normal speed? EDIT: Thanks for the replies. The VPS is 10 bucks a month and is from directvps.nl (Dutch host and I'm also dutch). I did two speed tests for disk IO: $ dd if=/dev/zero of=test bs=64k count=16k conv=fdatasync 1073741824 bytes (1.1 GB) copied, 23.1506 s, 46.4 MB/s $ dd if=/dev/zero of=test bs=64k count=16k conv=fdatasync 1073741824 bytes (1.1 GB) copied, 39.3796 s, 27.3 MB/s Anyway: how can I prove to my VPS host that it is to slow? I can understand a server being busy slowing a website down. But 5-30 sec loadtime for a normal PHP webpage?

  Read the article

• Creating a fallback error page for nginx when root directory does not exist

  - by Ruirize

  I have set up an any-domain config on my nginx server - to reduce the amount of work needed when I open a new site/domain. This config allows me to simply create a folder in /usr/share/nginx/sites/ with the name of the domain/subdomain and then it just works.™ server { # Catch all domains starting with only "www." and boot them to non "www." domain. listen 80; server_name ~^www\.(.*)$; return 301 $scheme://$1$request_uri; } server { # Catch all domains that do not start with "www." listen 80; server_name ~^(?!www\.).+; client_max_body_size 20M; # Send all requests to the appropriate host root /usr/share/nginx/sites/$host; index index.html index.htm index.php; location / { try_files $uri $uri/ =404; } recursive_error_pages on; error_page 400 /errorpages/error.php?e=400&u=$uri&h=$host&s=$scheme; error_page 401 /errorpages/error.php?e=401&u=$uri&h=$host&s=$scheme; error_page 403 /errorpages/error.php?e=403&u=$uri&h=$host&s=$scheme; error_page 404 /errorpages/error.php?e=404&u=$uri&h=$host&s=$scheme; error_page 418 /errorpages/error.php?e=418&u=$uri&h=$host&s=$scheme; error_page 500 /errorpages/error.php?e=500&u=$uri&h=$host&s=$scheme; error_page 501 /errorpages/error.php?e=501&u=$uri&h=$host&s=$scheme; error_page 503 /errorpages/error.php?e=503&u=$uri&h=$host&s=$scheme; error_page 504 /errorpages/error.php?e=504&u=$uri&h=$host&s=$scheme; location ~ \.(php|html) { include /etc/nginx/fastcgi_params; fastcgi_pass 127.0.0.1:9000; fastcgi_intercept_errors on; } } However there is one issue that I'd like to resolve, and that is when a domain that doesn't have a folder in the sites directory, nginx throws an internal 500 error page because it cannot redirect to /errorpages/error.php as it doesn't exist. How can I create a fallback error page that will catch these failed requests?

  Read the article

< Previous Page | 577 578 579 580 581 582 583 584 585 586 587 588  | Next Page >