Search Results

Search found 20997 results on 840 pages for 'adobe ideas'.

Page 621/840 | < Previous Page | 617 618 619 620 621 622 623 624 625 626 627 628  | Next Page >

• Debian can't connect to internet using LAN

  - by tampe125

  I have a headless Raspberry Pi using Debian Wheezy. I have a wifi dongle and if I connect my Raspberry using it, everything works fine: I can connect to the Internet, I can ping, I can update. However, if I get down my wifi and set up the lan interface, I lost my internet connection. I still can connect locally, using my laptop, but the connection doesn't exit (ie ping is not working). Some useful info: cat /etc/network/interfaces auto lo auto eth0 iface eth0 inet static address 192.168.0.105 netmask 255.255.255.0 gateway 192.168.0.1 ping www.google.com (nothing request timed out) ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:a2:b5:20 inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1130 errors:0 dropped:0 overruns:0 frame:0 TX packets:1116 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97223 (94.9 KiB) TX bytes:146140 (142.7 KiB) ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18007ms cat /etc/resolv.conf nameserver 8.8.8.8 netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 well, I think that's all... Any ideas?

  Read the article

• Tool to Save a Range of Disk Clusters to a File

  - by Synetech inc.

  Hi, Yesterday I deleted a (fragmented) archive file only to find that it did not extract correctly, so I was left stranded. Fortunately there was not much space free on the drive, so most of the space marked as free was from the now-deleted archive. I pulled up a disk editor and—painfully—managed to get a list of cluster ranges from the FAT that were marked as unused. My task then was to save these ranges of clusters to files so that I could examine them to try to determine which parts were from the archive and recombine them to attempt to restore the deleted file. This turned out to be a huge pain in the butt because the disk editor did not have the ability to select a range of clusters, so I had to navigate to the start of each cluster and hold down Ctrl+Shift+PgDn until I reached the end of the range (which usually took forever!) I did a quick Google search to see if I could find a command-line tool (preferably with Windows and DOS versions) that would allow me to issue a commands such as: SAVESECT -c 0xBEEF 0xCAFE FOO.BAR ::save clusters 0xBEEF-0xCAFE to FOO.BAR SAVESECT -s 1111 9876 BAZ.BIN ::save sectors 1111-9876 to BAZ.BIN Sadly my search came up empty. Any ideas? Thanks!

  Read the article

• pg_dump not working - do I need to change order of $PATH?

  - by A4J

  I'm trying to set the $PATH to pick up the latest version of pg_dump as I'm currently getting a mismatch error while doing a migrate in my Rails app (I recently changed the schema type to SQL). I have added a new file in /etc/profile.d called pg_dump.sh, and inside that put: PG_DUMP=/usr/pgsql-9.1 export PG_DUMP PATH=$PATH:$PG_DUMP/bin export PATH On looking at echo $PATH, I get: /usr/local/rvm/gems/ruby-1.9.3-p194/bin:/usr/local/rvm/gems/ruby-1.9.3-p194@global/bin:/usr/local/rvm/rubies/ruby-1.9.3-p194/bin:/usr/local/rvm/bin:/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin:/usr/pgsql-9.1/bin:/root/bin And I still get the error. Do I need to change the order? If so any ideas how? Output of 'ls /usr/pgsql-9.1/bin': clusterdb droplang pg_archivecleanup pg_ctl pg_standby psql createdb dropuser pg_basebackup pg_dump pg_test_fsync reindexdb createlang ecpg pgbench pg_dumpall pg_upgrade vacuumdb createuser initdb pg_config pg_resetxlog postgres vacuumlo dropdb oid2name pg_controldata pg_restore postmaster And output of 'which pg_dump': /usr/bin/pg_dump Error message on running cap 'deploy:migrate': ** [out :: 46.4.9.199] pg_dump: server version: 9.1.4; pg_dump version: 8.4.11 ** [out :: 46.4.9.199] pg_dump: aborting because of server version mismatch ** [out :: 46.4.9.199] rake aborted! ** [out :: 46.4.9.199] Error dumping database output of 'pg_dump --version': pg_dump (PostgreSQL) 8.4.11

  Read the article

• Windows 7 restarts while being idle

  - by Ondrej Slinták

  My Windows 7 almost always restarts when I keep it idle for ~20-30mins. It happened randomly before, but lately, if I leave the computer I can be sure it's gonna restart after those 30mins. It never happens when I play games or work tho, just when it's idle. It's a fresh install of Windows 7 64bit. I had also problems while installing it, it always crashed while finalizing the install and I had to reinstall again. Eventually it installed on 3rd or 4th try after I deleted all of my partitions and added them again. I thought it might have been a hardware problem, but temperatures seem to be okay and I have no idea how to track what might have been causing it. Any ideas? I'm running Windows 7 64bit on: Gigabyte EX58-UD4P Intel(R) Core(TM) i7 CPU 920 @ 2.67GHz NVIDIA GeForce GTX 260 6GB of DDR3 1066Mhz RAM WDC WD1001FALS-00J7B0 1TB SATA II I have a very bad feeling it might be something with HDD and its compatibility with Windows 7 as I haven't had those problems for 1 year while I had Vista. Edit: I checked Event Viewer critical errors from this night. PC restarted first time at 11:12pm, then at 3:06am and since then every ~20min until I came back to it. Error message is: The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. Source: Kernel-Power

  Read the article

• How do I fix Internet Explorer / Firefox differences in Oracle JD Edwards Enterprise?

  - by CT

  Our company uses Oracle's JD Edwards Enterprise to do accounting work. We have an application consultant working for us to just deal JD Edwards but he is of non-technical background so only helps in application-specific support. All of our users should use IE 7 for JDE. About 15-20% of those users have problems which cause them to not be able to use IE 7. So those problematic users use firefox. For the most part firefox works fine but there are a few issues. Some menus / options within JDE that are present in IE 7 are not present in firefox. If I could get all of our users working under IE 7, all the firefox issues would be mute points. I have cross referenced Internet Options settings from a working IE 7 user and a non-working IE 7 user. All settings seem to be mirrored. I'm not sure how to go about continuing to troubleshoot this issue. So not only answers but just suggestive ideas for attack would be appreciated. Thanks

  Read the article

• OpenVPN Server - CPU is pegged out

  - by ericl42

  Hello, I am configuring OpenVPN to act as a SSL tunnel for a remote location. I have OpenVPN1 at our current location acting as a server then OpenVPN2 at the other location that is acting as a client but is also acting as a DHCP server to machines behind it so they are basically connected to the local LAN. Everything is set up fine and I can talk from location A to location B with no problems like everyone is local. I am however having some performance issues. OpenVPN1 CPU is pegged to 100% the entire time I am copying or doing any type of activity through the tunnel. I expect some CPU usage going up but nothing like this. It's really killing my performance. OpenVPN1 is running in ESX right now with 2 gig RAM and 4 procs with unlimited bursting capacity. I am using AES-192 encryption with a 1024 key. Any idea how I can get my CPU down on OpenVPN1 and my download/upload speeds higher between the tunnel? Thanks. edit: Turning down the logging helped boost the throughput a little bit, but I am still fairly shy of where I believe I should be. Also I am still maxed out on the CPU. Does anyone have any ideas? I am really stuck on this. Thanks.

  Read the article

• WinHttpCertCfg not importing certificate

  - by Ramon Zarazua

  I need to setup a deployment script that imports an SSL certificate that my service uses. I have tried importing with WinHttpCertCfg and with CertMgr to no avail. Here are the command-line arguments I have tried to use with both: winhttpcertcfg.exe -i <certname>.pfx -c LOCAL_MACHINE\My -p <password> -a <user service runs as> and CertMgr.exe -add -all -s -r localMachine -c <cert name> My It seems from what I have investigated that CertMgr does not allow you to import certificates with a password, so I'd rather get winhttpcertcfg working. When I run them I get the following output: WinHttpCertCfg: Microsoft (R) WinHTTP Certificate Configuration Tool Copyright (C) Microsoft Corporation 2001. CertMgr: CertMgr Succeeded However, when I look into the local machine certificates in MMC, try to load them from my service, or list it out through winhttpcertcfg, or even looking at the registry in HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\SystemCertificates\MY\Certificates it is not found. I have tried all of the following: If I install the cert manually (Through CertMgr.msc dialogs) it works. The user installing is running as administrator The user installing has full access on the certificate The tools print out an error when something is wrong (wrong password) Tried it in multiple machines (All of them server 2008 R2) At this point I am officially out of ideas. Thank you.

  Read the article

• sporadic routing to another website when opening a common url

  - by user226098

  I have a strange problem in our office: Sometimes when opening a url from one of our projects random url in any browser not the right website shows up but some other website. In most of the cases it redirects to google.com with some parameters like https://www.google.de/?gfe_rd=cr&ei=krOOU8_kGcSKswadyYDQBw&gws_rd=ssl or just the ugly google 404 page). But today it remains on the origial url but shows up the the content of http://debug.netdna-cdn.com/. This happens about 1 time a week and for no apparent reason. Even stranger it only occurs on a single pc in the network. It now happens on two different computers in the network. Both use windows 8. The problem cannot be fixed by clearing the browser cache but by rebooting the pc or using ipconfig /flushdns. So I think it has something to do with the dns cache of the machine. But I have no idea what the reason is for this and how i can figure out how to solve it. Any ideas?

  Read the article

• Annoying trackpad freeze on MacBook [solved]

  - by Hafthor

  NOTE: Question marked answered because it was forced after being put up for bounty. Actual solution was to have Apple repair it. Trackpad usually works, but sometimes stops responding for around 5 seconds and then suddenly starts working again. Seems to happen when I switch between typing and moving + button-clicking and also when I do a lot of double-clicking. Tried turning off the "Ignore accidental trackpad input". Apple replaced the keyboard/mouse under warranty. Problem remains. Any ideas? Edit: White non-unibody Late-2008 13" MacBook - fully up-to-date OS. Doesn't seem to matter if it is plugged in or not. Edit: Updated to Snow Leopard - seems to have made it worse. Edit: Applying even a little pressure to the left palm rest creates this condition. Apple replaced the top case again and this time it seems to have fixed it. Although, it looks like they may have added a spacer on the left palm rest to "fix" it.

  Read the article

• AVConv increases song duration when converting MP3

  - by chauffch

  I am struggling with the following issue. I want to convert an MP3 ADTS into pure a MP3. I am using AVConv on Ubuntu 12.10. The outcome is a file that has the same size, but the duration is now longer. $ ls -l total 6436 -rw-r--r-- 1 teuf teuf 6586514 nov. 25 09:25 Blindsided_Bon_Iver.mpga $ file Blindsided_Bon_Iver.mpga Blindsided_Bon_Iver.mpga: MPEG ADTS, layer III, v1, 160 kbps, 44.1 kHz, JntStereo $ avconv -i Blindsided_Bon_Iver.mpga -c copy Blindsided_Bon_Iver.mp3 avconv version 0.8.4-4:0.8.4-0ubuntu0.12.04.1, Copyright (c) 2000-2012 the Libav developers built on Nov 6 2012 16:50:25 with gcc 4.6.3 [mp3 @ 0x8c6e240] max_analyze_duration reached Input #0, mp3, from 'Blindsided_Bon_Iver.mpga': Duration: 00:05:29.29, start: 0.000000, bitrate: 160 kb/s Stream #0.0: Audio: mp3, 44100 Hz, stereo, s16, 160 kb/s Output #0, mp3, to 'Blindsided_Bon_Iver.mp3': Metadata: TSSE : Lavf53.21.0 Stream #0.0: Audio: libmp3lame, 44100 Hz, stereo, 160 kb/s Stream mapping: Stream #0:0 -> #0:0 (copy) Press ctrl-c to stop encoding size= 6432kB time=329.30 bitrate= 160.0kbits/s video:0kB audio:6432kB global headers:0kB muxing overhead 0.002080% $ ls -l total 12868 -rw-rw-r-- 1 teuf teuf 6586129 nov. 27 22:26 Blindsided_Bon_Iver.mp3 -rw-r--r-- 1 teuf teuf 6586514 nov. 25 09:25 Blindsided_Bon_Iver.mpga $ file Blindsided_Bon_Iver.mp3 Blindsided_Bon_Iver.mp3: Audio file with ID3 version 2.4.0, contains: MPEG ADTS, layer III, v1, 32 kbps, 44.1 kHz, Stereo Amarok shows the new file has a duration of 25:27 and has a lot of silence. Am I using an incorrect option? Is it a bug in AVConv? Any ideas how to fix it?

  Read the article

• mount error 5 = Input/output error

  - by alharaka

  I am running out of ideas. After a long period of testing this morning, I cannot seem to get this to work, and I have no idea why. I want to mount a Windows SMB/CIFS share with a Debian 5.0.4 VM, and it is not cooperating. This the command I am using. debianvm:/home/me# whoami root debianvm:/home/me# smbclient --version Version 3.2.5 debianvm:/home/me# mount -t cifs //hostname.domain.tld/share /mnt/hostname.domain.tld/share --verbose -o user=SUBADDOMAIN.ADDOMAIN.DOMAIN.TLD/username mount.cifs kernel mount options: unc=//hostname.domain.tld\share,ip=10.212.15.53,domain=SUBADDOMAIN.ADDOMAIN.DOMAIN.TLD,ver=1,rw,user=username,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,pass=*********mount error 5 = Input/output error Refer to the mount.cifs(8) manual page (e.g.man mount.cifs) debianvm:/home/me# The word on the nets has not been very specific, and unfortunately it is almost always environment-specific. I receive no authentication errors. I have tried mount -t smbfs and mount -t cifs, along with smbmount and such. I get the same error before. I doubt it is a problem with DNS resolution, because logging shows the correct IP address. dmesg | tail -f no longer shows authentication errors when I format the domain and username accordingly. I have played a little with iocharset=utf8, file_mode, and dir_mode as described here. That did not help either. I have also tried ntlm and ntlmv2 assuming it might be a minimum auth method problem, but not forcing sec=ntlmv2 it can still authenticate without errors anymore. smbclient -L hostname.domain.tld -W SUBADDOMAIN.ADDOMAIN.DOMAIN.TLD -U username correctly lists all the shares and shows it as the following. Domain=[SUBADDOMAIN] OS=[Windows 5.0] Server=[Windows 2000 LAN Manager] Sharename Type Comment --------- ---- ------- IPC$ IPC Remote IPC ETC$ Disk Remote Administration C$ Disk Remote Administration Share Disk Connection to hostname.domain.tld failed (Error NT_STATUS_CONNECTION_REFUSED) NetBIOS over TCP disabled -- no workgroup available I find the last line intriguing/alarming. Does anyone have any pointers!? Maybe I misread the effin manual.

  Read the article

• Pinging switch results in alternating high/low response times

  - by Paul Pringle

  We have two switches that are behaving strangely. When I ping them the responses alternate between high and low results: C:\Users\paul>ping sw-linksys1 -t Pinging sw-linksys1.sep.com [172.16.254.235] with 32 bytes of data: Reply from 172.16.254.235: bytes=32 time=39ms TTL=64 Reply from 172.16.254.235: bytes=32 time=154ms TTL=64 Reply from 172.16.254.235: bytes=32 time=2ms TTL=64 Reply from 172.16.254.235: bytes=32 time=142ms TTL=64 Reply from 172.16.254.235: bytes=32 time=2ms TTL=64 Reply from 172.16.254.235: bytes=32 time=143ms TTL=64 Reply from 172.16.254.235: bytes=32 time=2ms TTL=64 Reply from 172.16.254.235: bytes=32 time=146ms TTL=64 Reply from 172.16.254.235: bytes=32 time=2ms TTL=64 Reply from 172.16.254.235: bytes=32 time=152ms TTL=64 Reply from 172.16.254.235: bytes=32 time=2ms TTL=64 Reply from 172.16.254.235: bytes=32 time=153ms TTL=64 Reply from 172.16.254.235: bytes=32 time=2ms TTL=64 Reply from 172.16.254.235: bytes=32 time=153ms TTL=64 Reply from 172.16.254.235: bytes=32 time=2ms TTL=64 Other switches in the network behave normally. I've rebooted the switches, but the behavior still is there with the ping. Any ideas on how to troubleshoot this? Thanks!

  Read the article

• Remote Socket Read In Multi-Threaded Application Returns Zero Bytes or EINTR (104)

  - by user39891

  Hi. Am a c-coder for a while now - neither a newbie nor an expert. Now, I have a certain daemoned application in C on a PPC Linux. I use PHP's socket_connect as a client to connect to this service locally. The server uses epoll for multiplexing connections via a Unix socket. A user submitted string is parsed for certain characters/words using strstr() and if found, spawns 4 joinable threads to different websites simultaneously. I use socket, connect, write and read, to interact with the said webservers via TCP on their port 80 in each thread. All connections and writes seems successful. Reads to the webserver sockets fail however, with either (A) all 3 threads seem to hang, and only one thread returns -1 and errno is set to 104. The responding thread takes like 10 minutes - an eternity long:-(. *I read somewhere that the 104 (is EINTR?), which in the network context suggests that ...'the connection was reset by peer'; or (B) 0 bytes from 3 threads, and only 1 of the 4 threads actually returns some data. Isn't the socket read/write thread-safe? I use thread-safe (and reentrant) libc functions such as strtok_r, gethostbyname_r, etc. *I doubt that the said webhosts are actually resetting the connection, because when I run a single-threaded standalone (everything else equal) all things works perfectly right, but of course in series not parallel. There's a second problem too (oops), I can't write back to the client who connect to my epoll-ed Unix socket. My daemon application will hang and hog CPU 100% for ever. Yet nothing is written to the clients end. Am sure the client (a very typical PHP socket application) hasn't closed the connection whenever this is happening - no error(s) detected either. Any ideas? I cannot figure-out whatever is wrong even with Valgrind, GDB or much logging. Kindly help where you can.

  Read the article

• My client's solution of a Windows SBS 2011 VM on an Ubuntu host and VirtualBox is pinning the host CPU

  - by Scott Stamp

  Here's my situation, I've got a client hosting two servers (one VM), with the host providing VMware Zimbra, the other Windows Small Business Server 2011. Unfortunately, the person before me had configured this setup as follows. Host: Ubuntu Desktop Edition 10.04 (I know, again, not my choice) running VMware Zimbra 8GB of RAM On-board RAID1 of two 320GB Seagate Barracuda drives for the OS Software RAID5 of four 500GB WD Caviar Black drives on MDADM for bulk storage (sorry, I don't know the model #) A relatively competent quad-core Intel Core i7 CPU from the Nehalem architecture (not suspicious of this as the bottleneck) Guest: Windows Small Business Server 2011 4GB of RAM Host-equivalent CPU allocation VDI file for OS hosted on the on-board RAID, VDI file for storage hosted on the on-board RAID For some reason when running, the VM locks up when sitting nearly idle, and the VirtualBox process reports values of 240%+ in top (how is that even possible?!). Anyone have any ideas or suggestions? I'm totally stumped on this one. Happy to provide whatever logs you'd like to take a look at. Ideally I'd drop VirtualBox and provision this with VMware Workstation, but the client has objected to the (very nominal) costs involved. If hardware needs to be purchased to help, it will be, but we're considering upgrades a last-resort at this time. Thanks in advance! *fingers crossed*

  Read the article

• Non-alphanumeric character folder name auto-completion problems

  - by viking

  I have been working with Windows 7's command line and have some folders that begin with non-alphanumeric characters. When I try to use tab completion to complete the folder name, the initial character is not included inside of the quotation marks. Example: C:\Users\username\!example is the folder I want to get into, but when I type: cd ! and press <Tab> to autocomplete, it will complete to cd !"!example" instead of the expected cd "!example" Any ideas on how to fix this besides changing the folder names? EDIT: I realize I could just tab through the entire list after entering cd, but I'm looking for a way to speed up the process. I have been spending a significant amount of time navigating these folders. UPDATE: This also happens if there is a space in the directory. For example: "c:\Program Files". In order to continue using tab to complete, first the second quote has to be deleted. C:\Program press Tab "C:\Program Files" is what appears. To navigate to a subdirectory, first the quote after Program Files has to be deleted before the next directory can be spelled out.

  Read the article

• NRPE: Unable to read output with check_connections plugin

  - by Wlodzimierz

  I'm using plugin which gives me warning or crtis with established connections. If I run it on local machine it gives: *root@graber:/usr/lib/nagios/plugins# ./check_connections -w 1 -c 5 -C sshd CRITICAL Established connections: 6* I know, I run as root. But: Rights to the file: root@graber:/usr/lib/nagios/plugins# ls -all check_connections -rwxr-xr-x 1 nagios nagios 5459 2012-07-06 10:19 check_connections /etc/sudoers: root@graber:/usr/lib/nagios/plugins# cat /etc/sudoers Defaults env_reset root ALL=(ALL:ALL) ALL %admin ALL=(ALL) ALL nagios ALL=(ALL) NOPASSWD: /usr/bin/lsof nagios ALL=(ALL) NOPASSWD: /usr/lib/nagios/plugins/ /etc/nagios/nrpe.cfg: *nrpe_user=nagios nrpe_group=nagios* *dont_blame_nrpe=1* *command_prefix=/usr/bin/sudo command[check_connections]=/usr/lib/nagios/plugins/check_connections -w 1 -c 5 -C sshd* log from remote: *2012-07-06T11:12:49+02:00 graber nrpe[25928]: Handling the connection... 2012-07-06T11:12:49+02:00 graber nrpe[25928]: Host address is in allowed_hosts 2012-07-06T11:12:49+02:00 graber nrpe[25928]: Host is asking for command 'check_connections' to be run... 2012-07-06T11:12:49+02:00 graber nrpe[25928]: Running command: /usr/lib/nagios/plugins/check_connections -w 1 -c 5 -C sshd 2012-07-06T11:19:11+02:00 graber nrpe[26100]: Return Code: 2, Output: NRPE: Unable to read output* Why is this happening? I'm out of ideas, I've searched google for 2 days now :)

  Read the article

• Completely remove and freshly install MySql on XP?

  - by Corey Ogburn

  I have read this question and have not found it as a solution and I have even attempted much more. I've uninstalled MySql 5.5.18 and deleted: C:\Program Files\MySql C:\Documents and Settings\All Users\Application Data\MySql After uninstalling, I restart the computer. When I reinstall, in the MySql Server Instance Configuration Wizard I leave everything to their defaults except: I add a firewall exception I check Launch MySQL Server Automatically I check Include BIN directory in windows path Enable root access from remote machines (I'll lock that down later, just debugging for now, I have also tried installing without this option to no avail) I've tried Typical and Complete while installing, as well as with and without strict mode. No combination shows a difference. After all this, it cannot Apply Security Settings and I get a 10061 error (it also said error number 2003) and this article didn't help. I've tried everything I can to completely uninstall and successfully reinstall so I can start from scratch. I've uninstalled and reinstalled about a dozen times with minor changes (including turning off the firewall at times), each time deleting the above folders and any proper registry entries with no success. Note by success, applying security settings and a working remote connection. I can connect locally every time, but it's remotely that counts. I have tried to look for exterior problems such as port forwarding in the router and (even though the installer should add it) I do double check the firewall settings, which have always allowed the default port. I'm out of ideas.

  Read the article

• SQL Server 2008 Bring Database Online trying to open a file from a drive that doesn't exist

  - by Nai

  This is my error I am facing TITLE: Microsoft.SqlServer.Smo Set offline failed for Database 'Go3D_Retailer ------------------------------ ADDITIONAL INFORMATION: An exception occurred while executing a Transact-SQL statement or batch. (Microsoft.SqlServer.ConnectionInfo) Unable to open the physical file "E:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\DATA\ftrow_Go3D_catalog.ndf". Operating system error 2: "2(failed to retrieve text for this error. Reason: 15105)". Database 'Go3D_Retailer' cannot be opened due to inaccessible files or insufficient memory or disk space. See the SQL Server errorlog for details. ALTER DATABASE statement failed. (Microsoft SQL Server, Error: 5120) Background to this error I've been trying to move my destination logshipping database to another physical server for analysis purposes. Because I do not have domain keys and active directory set up, I had to hack my process by using the same username/password for both the source and destination servers to get the process to work. Following that, I used this guy's solution to move the destination database to another server. However, this error occurs when I try to bring the database back online. I don't have an E drive on my server and I have no idea why it's trying to open a file from E drive. I have over a 100gb left on my hard disk so it's definitely not a space issue. This sounds like a bug... Any ideas?

  Read the article

• Debugging Windows PC freeze

  - by Violet Giraffe

  I have a problem with my computer, would appreciate any hints/ideas. It usually begins not immediately after booting Windows, but at some unpredictable point in time, which doesn't seem to correlate with any specific actions of mine. First sign of a problem is process System starting to consume 25% CPU time steadily. I have a quad-core CPU, so it might be one thread working non-stop. At this point micro-freezes start to occur - screen stops refreshing, but if I have, say, music player running - it continues playing. If I try to do something between the freezes, like open Start menu, it will freeze completely and forever. If I press reset button the PC will shut down and then start cold, as opposed to usual reset behavior (which doesn't include PC shutting down). I have noticed that full restart upon reset is usual for hardware problems, but I think this problem isn't related to at least motherboard-CPU-RAM-videoadapter. It certainly isn't caused by overheating. One very important not is that it seems to be related to Windows hosted WLAN network: I have USB Wi-Fi dongle and have configured a hosted network to share cable Internet connection with Wi-Fi devices. I am not 100% certain there's a strong connection, but in 9 or 10 cases when I enabled the network (by executing netsh wlan start hostednetwork), it did freeze eventually (sometimes within minutes of starting the network, sometimes within hours), and on at least 10 days when I didn't start the network it never froze, no matter how I used the computer). There are no critical/error entries in the events log that I can suspect as being related, only regular stuff like "driver not loaded". I have found no critical/error events that are being logged around the time of freeze occurring and are not logged during normal boot without starting the WLAN.

  Read the article

• esxi 5 monitoring

  - by user134880

  I'm new to esxi/vmware world. Have few question about monitoring esxi host. Now I'm using trial versian esxi 5.1 I can see performance charts in vShpere client. Cool. But I want to export this raw data (raw - I mean cvs,txt or some format which I can parse later) to other server to be able to parse this data later and create custom charts. (please do not advise to try vCenter, I need custom charts etc.) I could run esxtop in batch mode and use this data... But... How does vShpere client performance charts work? Where client takes data for charts? So if I will use esxtop batch mode it will add extra load to server. Is it possible to use same source as vSphere client use for charts? There is /var/lib/vmware/hostd/stats/hostAgentStats-20.stats file. Its looks like it is binary format. As I understood it is exactly data which I need?!?! Any ideas how to parse it? Thanks! PS: maybe some one know where to find, if there is one, info about processes running on esxi host?

  Read the article

• VMWare Setup with 2 Servers and a DAS (DELL MD3220)

  - by Kumala

  I am planning to use a VMWare based setup consisting of two VMWare servers (2 CPU, 256GB Memory) and a DAS (DELL MD3220 with 24x900GB disks). The virtual machines will be half running MS SQL databases (Application, Sharepoint, BI) and the other half of the VM will be file services, IIS. To enhance the capacity of the storage, we'll be adding a MD1220 enclosure with another 24x900GB to the MD3220. Both DAS will have 2 controllers. Our current measured IOPS is 1000 IOPS average, 7000 IOPS peak (those happen maybe twice per hour). We are in the planning phase now and are looking at the proper setup of the disks. The intention is to setup up both DAS one of the DAS with RAID 10 only and the other DAS with RAID 5. That will allow us to put the applications on the DAS that supports the application performance needs best. Question is how best to partition the two DASs to get best possible IOPS/MBps, each DAS will have to have 2 hot spares? For the RAID 5 Setup: Generally speaking, would it be better to have one single disk group across all 22 disks (24 - 2 hot spares) with both controllers assigned to the one disk group or is it better to have 2 disk groups each 11 disks, assigned to one of the two controllers? Same question for the RAID 10 setup: The plan is: 2 disks for logs (Raid 1), 2 Hotspare and 20 disks for RAID 10. Option 1: 5 * 4 disks (RAID 10), with two groups assigned to 1 controller and 3 groups to the other controller Option 2: One large RAID 10 across all the disks and have both controllers assigned to the same group? I would assume that there is no right or wrong, but it all depends very much on the specific application behaviour, so I am looking for some general ideas what the pros and cons are of the different options. IF there are other meaningful options, feel free to propose them.

  Read the article

• Autologin 2 Windows users OR Login another user from the desktop

  - by fpdragon

  I'm using two windows users on my HTPC at the same time. One is just for watching videos and one for administration via remote. This setup is quite ideal for me since windows can handle multiple concurrent logins and the win "rdp concurrent hack" (Google). The problem is, I want both users to be logged in automatically when the pc was started. It shall be possible to watch tv and also the admin user shall be automatically logged in to start my scripts and other tasks, even if I haven't logged in via remote desktop manually. Later, when I want to admin my htpc I can just rdp connect the admin user without interrupting the video playback on the actual HTPC's screen and check my cleanup tasks, downloads, ... witch already executed for this admin user. But right now I found no solution to automatically login user A from a user B desktop and I also found no solution to autologin both users immediately at startup. As a workaround I have to fire up my other notebook machine and login one time with the remote user via rdp. From this time on the remote admin user is running concurrent with the main user in the background of the machine. The other workaround would be... after startup switch user from main user to admin user and then back again. But that also requires manual steps. I'm on a Windows 8 System right now but all infos for Win7 or XP would be also interesting. thanks a lot for all ideas. PS: just to prevent useless posts... don't tell me that only one user can be logged in to windows. ;)

  Read the article

• Making libmagic/file detect .docx files

  - by Jonatan Littke

  As seen elsewhere, docx, xlsx and pttx are ZIPs. When uploading them to my web application, file (via libmagic andpython-magic) detects them as being ZIP. I store the contents of the file as a blob in the database, but naturally I don't want to trust the user with what kind of file type this is. So I would like to trust file for and automatically generate a filename during download. I know one can modify /etc/magic but the format (magic(5)) is way too complicated for me. I found a bug report on the issue at Debian bugs but since it's from 2008 it doesn't seem to be fixed any time soon. I guess my only other alternative is to indeed trust the user (but still store the contents as a blob) and only check the file extension based on the file name. This way I can disallow some extensions and allow others. And when the user re-downloads his file, he can have it in whatever way he uploaded it. But this solution is insecure if the file is shared with others, since you can simply rename the file to allow uploading it. Any ideas? Lastly, I found a list of magic numbers for docx etc, but I'm unable to convert these into the magic(5) format.

  Read the article

• Cant access folder on server- Permission denied

  - by Michal Korzeniowski

  I am running a vps with ubuntu 11.04. After a clean Modx install I've tried to access http://www.encepence.pl/manager and I've got a permission denied by my server. the thing is that I can easily access any other folder under that domain and modify this folder(manager) content via ftp. I’ve tried modifying virtual host with that <Directory /var/www/blackflow/data/www/encepence.pl/manager/> Options Indexes FollowSymLinks ExecCGI AllowOverride All Order allow,deny Allow from all </Directory> But it didn't work. <Directory /var/www/blackflow/data/www/encepence.pl> Options -ExecCGI -Includes php_admin_value open_basedir "/var/www/blackflow/data:." php_admin_flag engine on </Directory> <VirtualHost 192.166.219.34:80 > ServerName encepence.pl CustomLog /var/www/httpd-logs/encepence.pl.access.log combined DocumentRoot /var/www/blackflow/data/www/encepence.pl ErrorLog /var/www/httpd-logs/encepence.pl.error.log ServerAdmin [email protected] ServerAlias www.encepence.pl SuexecUserGroup blackflow blackflow AddType application/x-httpd-php .php .php3 .php4 .php5 .phtml AddType application/x-httpd-php-source .phps php_admin_value open_basedir "/var/www/blackflow/data:." php_admin_value sendmail_path "/usr/sbin/sendmail -t -i -f [email protected]" php_admin_value upload_tmp_dir "/var/www/blackflow/data/mod-tmp" php_admin_value session.save_path "/var/www/blackflow/data/mod-tmp" VirtualDocumentRoot /var/www/blackflow/data/www/%0 </VirtualHost> Any ideas on what might have gone wrong?

  Read the article

• Data Store/Volume disconnecting. How to resume copy of VMDK?

  - by Serge

  I'm having an issue with my ESXi 4.1 hosts losing the datastore with FC SAN after a power outage. All 3 hosts disconnect so it's definitely a SAN issue. I've tried to resolve the issue on the SAN side with the SAN software support and Adaptec hardware support. No luck there. So I'm stuck with a SAN that will randomly disconnect the volume. I need to get the virtual machines (VMDK files) from the datastore. The problem is I can only get 5-20% before the data store disconnects. I have backups that are slightly older that I can use to replicate the VMDK differences to. What has not worked so far: Powering up the VMs, will boot up for 5-15 minutes then freeze vCenter migrate or clone of VM, will fail after similar period of time vCenter copy/paste of VMDK. Was able to get one 30GB VMDK and no luck after that. vMware Data Recovery. Fails at low %, can't resume, so next backup starts from begining. Veeam Backup & Recovery. Same as above, no resume function. If I can just find a backup solution that will resume from the failed spot that would solve my issue. Anyone have any ideas that I could try? EDIT 1 The SAN is Open-E DSS 6 running on a Supermicro 24 drive enclosure with 4 port Qlogic FC. Adaptec 52445 RAID card.

  Read the article

< Previous Page | 617 618 619 620 621 622 623 624 625 626 627 628  | Next Page >