Search Results

Search found 20997 results on 840 pages for 'adobe ideas'.

Page 623/840 | < Previous Page | 619 620 621 622 623 624 625 626 627 628 629 630  | Next Page >

  • iptables secure squid proxy

    - by Lytithwyn
    I have a setup where my incoming internet connection feeds into a squid proxy/caching server, and from there into my local wireless router. On the wan side of the proxy server, I have eth0 with address 208.78.∗∗∗.∗∗∗ On the lan side of the proxy server, I have eth1 with address 192.168.2.1 Traffic from my lan gets forwarded through the proxy transparently to the internet via the following rules. Note that traffic from the squid server itself is also routed through the proxy/cache, and this is on purpose: # iptables forwarding iptables -A FORWARD -i eth1 -o eth0 -s 192.168.2.0/24 -m state --state NEW -j ACCEPT iptables -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A POSTROUTING -t nat -j MASQUERADE # iptables for squid transparent proxy iptables -t nat -A PREROUTING -i eth1 -p tcp --dport 80 -j DNAT --to 192.168.2.1:3128 iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 80 -j REDIRECT --to-port 3128 How can I set up iptables to block any connections made to my server from the outside, while not blocking anything initiated from the inside? I have tried doing: iptables -A INPUT -i eth0 -s 192.168.2.0/24 -j ACCEPT iptables -A INPUT -i eth0 -j REJECT But this blocks everything. I have also tried reversing the order of those commands in case I got that part wrong, but that didn't help. I guess I don't fully understand everything about iptables. Any ideas?

    Read the article

  • Logitech QuickCam Pro 9000 & Windows 7 64-bit failing miserably

    - by Saxtus
    I am trying to install a Logitech QuickCam Pro 9000 webcam to Windows 7 64-bit. If I do it without using the Logitech drivers but instead the Windows Update ones, the camera works with low frame rate and without face tracking and all other bells and whistles that it's full driver provides. The moment I install the latest official Logitech driver, the problems begin: Camera works fine, until I decide to go to audio settings of the LWS panel or Windows'. Then LWS freezes and with it everything that tries to output audio. I am not able to open Playback/Recording devices window (it just doesn't appear) and system gets unstable and slow with LWS.EXE process not been able to close forcefully. If I reboot and forget the camera connected, this situation continues and system gets unstable from the beginning. If I reboot without the camera connected, everything works fine until I connect it and try to do something with audio settings of Windows or LWS panel. I should note, that until the freezing occurs, camera works as expected, with full frame rate, face tracking and everything that is expected to do. The soundcard is the ASUS SupremeFX II of the ASUS Striker II Extreme motherboard. Any ideas of what is causing this or what else to try so I can make it work as advertised? Thank you.

    Read the article

  • LG LW20 Express won't boot after hdd replace

    - by Mika
    My old laptop (LG LW20 Express) got a hdd failure and I replaced the hdd. Now the laptop won't boot from cd or usb. I'm trying to install ubuntu on it. When I turn the laptop on it shows me the startup screen but when it should be the time to load operating system it just gives a black screen and starts over. This loop continues until I shut down the laptop. I created the usb boot drive following this guide https://help.ubuntu.com/community/Installation/FromUSBStick/ I used my boot cd to install ubuntu on this machine I'm using right now. So at least the cd should work. From the BIOS I can see that my newly installed hdd is recognized and put as a secondary master. Also the cd and removable media are in the boot list before hdd. The laptop runs pretty hot. The fan is at full speed pretty soon after the laptop is turned on. Earlier I suspected that it would have been the almost broken hdd that would have produced that heat but there obviously is something else also. Any ideas what to check?

    Read the article

  • Nagios check_host_alive and check_ping not showing host as down

    - by Kyle
    I am using the check_host_alive command to send 5 packets every minute to all my routers at remote locations. I noticed today I received a notification from The AT&T Global Client Support Center that a router was down (which can take 5-30 minutes to send these notices out) and never received a notice from Nagios. I went onto Nagios and it is was showing the host as alive with a latency of 0ms. This tells me it is seeing the automated response from my router in the data center that, "TTL expired in transit" as a reply from the remote router. Is there anyway for me to tell nagios to check where the reply is comming from? I feel like other people have to of had this issue... I tested it with the check_ping command and it produced the same results. I have the command defined has %hostname% and the proper IP in the host definition, and it works fine for telling me the latency is high. Any ideas are welcome, I have already exercised my Google skills with no results. EDIT: root@IM-UBTU:/# /usr/local/nagios/libexec/check_ping -H 192.168.250.1 -w 100.0,10% -c 200.0,20% -vvv CMD: /bin/ping -n -U -w 10 -c 5 192.168.250.1 Output: PING 192.168.250.1 (192.168.250.1) 56(84) bytes of data. Output: From 10.69.10.2 icmp_seq=1 Time to live exceeded It knows something is wrong why doesn't it give me a warning?

    Read the article

  • Can I take my ReadyNAS drive in Raid1 and plug it straight into new different machine?

    - by jacko
    I would assume that I can just take my HDD out of my NAS (in raid1 mirror) and plug it into another enclosure and have it work off the bat but I'd like to make sure... Any ideas? Edit: My current setup is a Netgear ReadyNAS in (hardware) raid1. I'm hoping to replace this with a home theatre type PC (possibly running Ubuntu), and would like to migrate my data without having to do a bulk transfer over my network between the 2 machines. Can anyone confirm the case for the Netgear ReadyNAS? Edit: Ok after further reading it seems that the ReadyNAS Duo formats my drive as ext3 in 16k blocks. There are instructions for mounting a drive into a linux box here: Mounting Sparc-based ReadyNAS Drives in x86-based Linux There is also talk about a linux image here: ReadyNAS Data Recovery - VMware recovery tool I'm not sure whether this means they ReadyNAS actually implements software raid under the hood, or what? So it appears like it IS do-able, but do any of you linux guru's know whether this is viable and whether the fact that they are in raid 1 affect matters?

    Read the article

  • SQL Server becomes slow after restart

    - by Tobi DM
    I already posted this one on stackoverflow but someone gave me the hint to that I might have more luck on serverfault. We use SQL Server 2005 on an Windwos Server 2008. Ther Server has 48 GB RAM. SQL Server is configured to use 40 GB RAM. There is only one database hosted (About 70 GB). The only app beside SQL Server is our App-Server which connects the clients to the database. Now we encounter the following problem: After a restart of the server our the performance is great. The server grabs the 40 GB RAM wich it is allowed to and then runs fast as hell. But after about 4 weeks the system becomes slower and slower. The execution of statements (seen in the profiler) is raising slowly. But I cannot see that there is something going wrong on the server. CPU usage is at about 20% I/O also seems to be no Problem The process monitor does also not show that there are strange apps or something like that. Eventlog does also have no interessting messages No open transactions or blockings to see We do not use cursors in our app We tried already the following things without effect: Droped the cache by using the statements DBCC FreeProcCache DBCC FREESYSTEMCACHE('ALL') DBCC DropCleanbuffers Restarted the Appserver we are using. Restart the sql server service But nothing did help exept restarting the whole server. Any ideas?

    Read the article

  • Backup plan for linux webserver in small business?

    - by radman
    Hi, I am currently in the process of writing a backup plan for the webserver in use by my business. I am very new to this area and have a few ideas about how things should work but am unsure of what tools to use and what sort of restore process is appropriate. I'm looking for something relatively simplistic and it doesn't have to be 100% paranoid just enough to give me a reliable backup. Speed is not of the essence and there is not going to be a live fallback in place. The backup will be onto a single hdd that will be stored onsite (no option for offsite as yet). Backups will be taking place weekly. I am constrained by both time and money which is why I'm aiming for a good enough solution. Is taking an image of the webserver system drive periodically and using that as the backup appropriate? Should I be testing that the backups restore correctly every time that I perform one? This is a bit broad but what setup would you use if you were in my place, given the services I am running? Should I add additonal machines and split the services? Any advice is much appreciated! See below for server details Webserver Platform Linux Ubuntu server Running mail-server svn-server mediawiki wordpress apache-webserver Hardware single 500gb sata drive Architecture Single machine behind router (with firewall) accessible to the internet.

    Read the article

  • SSL timeout on some sites, across all browsers, on Mac OS X Snow Leopard

    - by dansays
    For the past several weeks, I've been receiving "Error 7 (net::ERR_TIMED_OUT): The operation timed out" when I attempt to connect to either Twitter or Paypal via SSL. I get this specific error in Google Chrome, but the same problem occurs in both Safari and Firefox. Other sites work fine, and other computers on my network can access these two sites. I have no firewall settings that would prevent me from accessing these sites over port 443. I notice that both Twitter and Paypal both have "Verisign Class 3 Extended Validation SSL CA" certificates. It is unclear whether this is related to the problem. In an effort to troubleshoot, I attempted to open the test sites referenced on Verisign's root certificate support page, which worked fine. Just to be sure, I downloaded and installed the root package file and installed all included Verisign certificates. No joy. I feel like I've hit a dead end. Any ideas? Update the first: I also cannot connect to FedEx.com, who also has a Verisign Class 3 Extended Validation cert. Update the second: Aaaaaaand it fixed itself. I did nothing. Or, I did something that worked, but in a delayed fashion. Frustrating, but a win is a win. I'll take it.

    Read the article

  • Live Screencast under Linux

    - by OmnipotentEntity
    I was having some difficulty with running a Live Screencast under Linux. I've found jtvlc and tried using that, but whenever I use it the stream comes out either blank or lagged with extremely high latency. I have a fast internet connection and a fast computer, but am I perhaps taxing it too much? Any ideas on what I could possibly be doing wrong? # 1. Get an account on http://www.justin.tv/ # 2. Copy streaming key from: http://www.justin.tv/broadcast/adv_other # 2. Install VLC: http://www.videolan.org/vlc/ # 3. Get Win/Mac/Lin Stream Client: \ # http://apiwiki.justin.tv/mediawiki/index.php/Linux_Broadcasting_API # 4. Adjust the vlc parameters to your liking and run VLC like this #!/bin/bash cvlc screen:// --input-slave=pulse:// \ --screen-width 1920 \ --screen-height 1080 \ --screen-fps 5 \ -v input_stream \ --sout='#duplicate{ dst="transcode{ scale=1, venc=x264{ keyint=60 }, vcodec=h264, vb=600, acodec=mp4a, ab=32, channels=2, samplerate=22050 } :rtp{dst=127.0.0.1,port=1234,sdp=file:///tmp/vlc.sdp} "}' \ --sout-transcode-threads=4 & sleep 2 # 5. Run JTVLC to stream like this: ./jtvlc/jtvlc omnipotententity censored /tmp/vlc.sdp # Notes: #- If you want to see what you're about to stream add 'dst=display, ' # before 'dst="transcode[' # More about the VLC parameters: http://wiki.videolan.org/Documentation:Modules/screen

    Read the article

  • Wildcard DNS entry to match lang subdomain

    - by Adam Benayoun
    Hey, We have a website www.example.com pointing to x.x.x.1 and a system with multiples minisites all having subdomains.examples.com pointing to x.x.x.2 Basically what we have in place is a wildcard DNS entry who could basically match any possible subdomain, once reaching x.x.x.2, the apache vhost would intercept and basically redirect it to a php script who in turn would know what minisites to serve. On www.example.com however, we server contents which are translates in several languages, until few weeks ago you could switch languages by clicking on a flag and you'd be served with the translated content. The only problem is that the URL wouldn't change and SEO wise this isn't the best solution. Now I cannot change the way subdomain are handled (being redirected to x.x.x.2) since we have hundreds, if not thousands of minisites live. I have to come up with a solution to have language.example.com redirecting to x.x.x.1 and then a rewrite rule who would basically rewrite the fake subdomain into a URL in order to pass the parameter of the language to example.com On solution is to list all possible language as DNS entries right before the wildcard DNS entry. The other solution which I am almost sure is not feasible is to have some kind of regex in a DNS entry matching all subdomain with 2 letters ( en|es|fr|cn|cl etc... ) Any ideas?

    Read the article

  • Connect linux server to VPN server via PPTP

    - by wowpatrick
    I'm trying to connect a Linux (Ubuntu 10.04 LST) server to a VPN server via the PPTP client to an VPN server. I configured the PPTP client as said in the documentation. The connection is correctly added as an interface, but somehow the connection dose not work. ping -I ppp0 google.com dose not return anything and traceroute -i ppp0 only shows the first hop, and then displays nothing. Any ideas of what is going wrong? Incorrect routing configuration? ifconfig output for the configured interface: ppp0 Link encap:Point-to-Point Protocol inet addr:xx.x.xxx.xxx P-t-P:10.0.0.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1496 Metric:1 RX packets:415 errors:0 dropped:0 overruns:0 frame:0 TX packets:468 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:31428 (31.4 KB) TX bytes:32394 (32.3 KB) route output Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface xx.x.x.1 * 255.255.255.255 UH 0 0 0 ppp0 xx.xxx.xxx.xx sp.ip 255.255.255.255 UGH 0 0 0 eth1 192.168.3.0 * 255.255.255.0 U 0 0 0 eth2 192.168.2.0 * 255.255.255.0 U 0 0 0 eth1 default sp.ip 0.0.0.0 UG 100 0 0 eth1

    Read the article

  • Laptop battery holds charge, but won't charge any more.

    - by Jeff
    Ok, I'm sure I will need to replace either my battery or my AC adapter, but would rather not buy one if the other is the problem. My problem is. I have a Sager laptop that gets quite a bit of use. The charging has always been a little bit odd. If I was in the process of using it, it would charge just fine and stay On AC power. If I left it alone, however(power settings to ONLY turn off the monitor) in either Ubuntu or Windows 7 it decides that it didn't want to use AC power anymore and would just start draining the battery until it died. Now, suddenly, it won't charge at all. The capacity was great up to this point which happened in an instant. It will recognize the battery but won't see the AC power if plugged in while the battery is in. I can power up the laptop without the battery and it works fine. If I plug in the battery while powered up it will claim it's charging it, but it stays at the same percentage. If I unplug the power, it will switch over to Battery fine, but I have to power down and unplug the battery to get it back on AC power. I've had dying/dead batteries before but they typically won't hold a full charge anymore but it still winds up to 100% then drops quickly when unplugged. This seems more like a chip problem in the battery to me, but I'm not sure. Any ideas?

    Read the article

  • Western Digital My Book not recognized by WD software

    - by Kari
    A few years ago I bought a WD My Book Pro 2. It worked fine for a while, then one of the drives failed and I sent it back to be replaced under warranty. I never got around to setting up the new one when I got it back. I finally ran out of room on my internal drive, so I tried to use the external - no go. Both drives spin up, but aren't recognized by either Disk Utility (Mac) or the WD Drive Manager. I tried on a PC as well with fresh software. Then I pulled the drives out of the enclosure (warranty is already expired) and plugged them straight into the PC. Both recognized and working 100% in RAID0. BIOS recognizes either disk as functional; Windows only sees them when both are connected due to the RAID which I can't change without the WD software. The drives that were returned to me are the "Green" drives which I've read are NOT recommended for RAID. Is it possible that this is interfering with them reading externally? Any other ideas? My main computer is a laptop so using them internally isn't an option :(

    Read the article

  • Ping and crawling not working, site still resolving

    - by Andrew Alexander
    Ok, so we're trying to figure out why the site of one of our clients isn't being crawled by Google (we've ruled out robots.txt or meta tags) When we go to the site, either IP address or domain name, the site resolves, everything works. However, Google is getting a 302 redirect (which it apparently isn't following for crawling), and when we ping the address, it times out (note, the site is still resolving in the browser throughout all of this). The site is built in ASP.Net (I assume C#) and so my thoughts were that it was an errant redirect rule, or some other sort of server side issue. We also thought that it might be due to incorrect domain pointing (but if we try to ping the IP, it doesn't work, so that sorta rules that out). We're really not sure what is causing all of these errors, or even if they have one single source. Anyone have any ideas what could be going on? Do you need any more information? To boil it down in a TL; dr: * Site resolving in browser, both IP and domain name. No problems here. * Site not being crawled by Google (gets a 302 it doesn't seem to follow) - it is not due to robots.txt or meta tags * Ping is not working for the IP address. This is very odd, because again, the IP address seems to work fine in the browser. * Our thoughts are either redirect rule issue, domain pointing issue, or possibly some errant code - or some combination of the three

    Read the article

  • Terminal Server 2008 Login: Access Denied

    - by user1236435
    When I try to RDP into a Server 2008 Terminal Server, I get a message that says "Access Denied" and an OK button. I setup the licensing mode correctly (per user) and also have setup to allow all remote connections. I get the following in the security event log: Log Name: Security Source: Microsoft-Windows-Security-Auditing Date: 28/06/2012 12:01:16 Event ID: 4656 Task Category: File System Level: Information Keywords: Audit Failure User: N/A Computer: 0BraApps1.brenntagLA.hou Description: A handle to an object was requested. Subject: Security ID: BRENNTAGLA\jaadmin Account Name: jaadmin Account Domain: BRENNTAGLA Logon ID: 0xbbe3f Object: Object Server: Security Object Type: File Object Name: C:\Windows\System32\ServerManager.msc Handle ID: 0x0 Process Information: Process ID: 0x60c Process Name: C:\Windows\System32\mmc.exe Access Request Information: Transaction ID: {00000000-0000-0000-0000-000000000000} Accesses: READ_CONTROL SYNCHRONIZE WriteData (or AddFile) AppendData (or AddSubdirectory or CreatePipeInstance) WriteEA ReadAttributes WriteAttributes Access Reasons: READ_CONTROL: Granted by D:(A;;0x1200a9;;;BA) SYNCHRONIZE: Granted by D:(A;;0x1200a9;;;BA) WriteData (or AddFile): Not granted AppendData (or AddSubdirectory or CreatePipeInstance): Not granted WriteEA: Not granted ReadAttributes: Granted by ACE on parent folder D:(A;;0x1301bf;;;BA) WriteAttributes: Not granted Access Mask: 0x120196 Privileges Used for Access Check: - Restricted SID Count: 0 Event Xml: 4656 1 0 12800 0 0x8010000000000000 1535565 Security 0BraApps1.brenntagLA.hou S-1-5-21-205301047-3902605089-2438454170-21511219 jaadmin BRENNTAGLA 0xbbe3f Security File C:\Windows\System32\ServerManager.msc 0x0 {00000000-0000-0000-0000-000000000000} %%1538 %%1541 %%4417 %%4418 %%4420 %%4423 %%4424 %%1538: %%1801 D:(A;;0x1200a9;;;BA) %%1541: %%1801 D:(A;;0x1200a9;;;BA) %%4417: %%1805 %%4418: %%1805 %%4420: %%1805 %%4423: %%1811 D:(A;;0x1301bf;;;BA) %%4424: %%1805 0x120196 - 0 0x60c C:\Windows\System32\mmc.exe Any ideas?

    Read the article

  • NTLM, Kerberos and F5 switch issues

    - by G33kKahuna
    I'm supporting an IIS based application that is scaled out into web and application servers. Both web and applications run behind IIS. The application is NTLM capable when IIS is configured to authenticate via Kerberos. It's been working so far without a glitch. Now, I'm trying to bring in 2 F5 switches, 1 in front of the web and another in front of the application servers. 2 F5 instances (say ips 185 & 186) are sitting on a LINUX host. F5 to F5 looks for a NAT IP (say ips 194, 195 and 196). Created a DNS entry for all IPs including NAT and ran a SETSPN command to register the IIS service account to be trusted at HTTP, HOST and domain level. With the Web F5 turned on and with eachweb server connecting to a cardinal app server, when the user connects to the Web F5 domain name, trust works and user authenticates without a problem. However, when app load balancer is turned on and web servers are pointed to the new F5 app domain name, user gets 401. IIS log shows no authenticated username and shows a 401 status. Wireshark does show negotiate ticket header passed into the system. Any ideas or suggestions are much appreciated. Please advice.

    Read the article

  • port forwarding problem

    - by Claudiu
    I want to set up an svn server on my computer, so it's available from anywhere. I think I set up the repository correctly, using CollabSVN. If I go to Repo-Browser with TortoiseSVN and point it to svn://localhost:3690, it shows the proper repository. The problem now is that I'm behind a router. My local IP is 192.168.1.45 . Doing svn://192.168.1.45:3690 also works. My global IP is, say, x.x.x.x. Just doing svn://x.x.x.x:3690 doesn't work, which makes sense, since I have to set up port forwarding. I'm using a Verizon router. Using their web interface (on 192.168.1.1) I added the following port forwarding rule: IP Address forward to: 192.168.1.45 Source Ports: Any Dest Ports: 3690 Forward to: 3690 Protocol: TCP However, even after applying this rule, going to svn://x.x.x.x:3690 doesn't work. It takes a few seconds to fail, then says that the connection couldn't be established because the server connected to didn't respond properly after a period of time. What's interesting is that a random port, like svn://x.x.x.x:36904 fails immediately, saying that the target machine actively refused the connection. So I figure that the forwarding rule did something, but not fully what was necessary. Any ideas on how to get this working? The router model is MI424-WR and the firmware version is 4.0.16.1.56.0.10.12.3. UPDATE: I also tried setting destination port to 45000, and still forwarding to 3690, in case something was wrong w/ the lower-numbered ports, but to no avail. I also tried port 80 to port 3690, still all in vain.

    Read the article

  • Parallels Plesk returning strange numbers

    - by Jack W-H
    Hi everyone, As a relatively new Server Admin I've become a bit confused by some statistics Parallels Plesk Panel 10.0.1 is returning to me. I have a domain ('subscription') set up, mysite.com. Mysite.com only hosts files, mostly images Its file contents use up about 390MB of disk space Here's a screenshot: this is what Plesk is reporting mysite.com to use: And some more info: Now this is pretty confusing... I thought at first my site might have been hacked and had contents written to disk, but I checked and all is in order, nothing has been hacked into as far as I can tell. So I had a look in the site's CP for some more in-depth statistics, and this is what's returned... Now - sod's law - when I go to check my disk space statistics in more depth via the control panel, this morning it says "The data were not collected yet." - not too sure what that means, but, last night when I checked it was reporting something odd. It said Files were using up 390MB, but 1.80GB or so were being used up by 'Mail Accounts'. This is really strange, as there are no mail accounts set up for the domain. The only hint of 'mail' there is, is the catchall set up to forward *@mysite.com to a separate, ISP-hosted email account. Any ideas anybody? I can post more details if you need it. Sorry to be a bit vague but I'm not sure what else I can post. Thanks, Jack

    Read the article

  • White Screen, No Errors.

    - by GruffTech
    So.. Interesting problem for you guys, As I'm completely lost as to what to do, or where to take the next step. Server & Application Environment. CentOS release 5.3 (Final) Apache 2.2.3-22 EnableSendfile off EnableMMAP off ErrorLog logs/error_log LogLevel debug PHP-5.2.6-2 error_reporting = E_ALL display_errors = on log_errors = on max_execution_time=300 max_input_time=60 memory_limit=512mb Kohana 2.3 PHP Environment. HAProxy 1.3.15.6-2 MemCacheD 1.2.6-1 Our application is split between 3 web servers, mounting a NFS Storage server, and sticky load balancing between the 3 web servers. The application seemingly runs great, but every so often, instead of loading, the application just shows a pure white page. Not a 404 Error, or a 500 Server Error, a clean white page. And it returns instantly, so its not a execution time error. Nothing in the Error log, or Server-Error Log, Proxy log shows standard proxied connection, Just the standard 200-Status in Access log, with 256 bytes transferred. To me, this leads to tell me that the application itself is having a problem. A rare, unexplainable, seemingly random, problem that causes what we've now called the "White Screen of Death." Our developers all say that since there is nothing going to our error logs, that it must be a server problem. But I say the same thing, There's nothing going to ANY of our logs (relevent to this anyway), and we're not having httpd children crash from what i can tell. Any ideas on how i can increase my logs, or somehow prove that its not a bug in PHP, Apache, CentOS, ect? Or if it is somehow a bug, identify it?

    Read the article

  • Slow Local Network, Windows 7, Snow Leopard, WiFi/Wired

    - by WerkkreW
    Hello - I am experiencing really poor local network performance in my home. I was recently using a Linksys WRT54G Router with DD-WRT on it, and a couple comparable Linksys-G PCI cards for connectivity but decided to upgrade hoping it would help with my performance issues. The computers in my house are connected as follows: Comcast Business Class Commercial 25mbps/10mbps (Verified with SpeakEasy and Speedtest.net) D-Link DGL-4500 Wireless N Router Windows 7x64 - D-Link DWA-552 Wireless-N Windows 7x64 - D-Link DWA-552 Wireless-N Mac Mini 10.6.2 - AirPort Extreme N Playstation 3, Hard Wired Xbox 360, Hard Wired Essentially the problem is very specific. Web browsing and uploading/downloading files from the internet is fine, more than fine. But if I want to say, Stream a video from one of my Windows 7 computers to my PS3, or copy a large video file between either of the PC's or the Mac, I get a consistent 500-900Kbps throughput at the high end. If I open my network browser, or try to browse my homegroup the response time is horrible. Both of my Windows computers are showing Strong wireless signals with a connection speed of 300Mbps. I know I can never expect to achieve anything near those speeds, but 500Kbps? Here is what I have tried so far: Enabled Single mode N-only and N/G Only on router WPA2 with AES Encrpytion Disabled "Remote Differential Compression" in Windows 7 Disabled TCP "Auto-Tuning" Used other software for file copies such as "Teracopy" I am at the end of my rope. Unfortunately I live in a 75 year old home with plaster walls, so hard-wiring my entire house isn't really an option I can handle right now. Any ideas to help me get decent speed when transferring files across my network would be greatly appreciated.

    Read the article

  • PTR record not valid for all domains

    - by charnley
    We have an issue sending emails to certain domains, namely Time Warner and Cox. Last week, we decommissioned our Exchange 2003 server and now our Exchange 2010 server is doing all of the transport for our domain. We run our own authoritative name servers, so we are in charge of the DNS and have modified our PTR record to reflect the new server. All mailflow is working except for these 2 domains. When I telnet on port 25 to the mail servers for Cox and Time Warner I am receiving errors. For Cox the error is: 554... rejected - no rDNS And when I telnet to port 25 to the Time Warner mail server we get this: 554 5.7.1 - Connection refused. IP name lookup failed for x.x.x.x I have run through the outbound SMTP test on Microsoft Remote Connectivity Analyzer and get 100% completely successful results. MXToolbox comes up with all successful tests on SMTP as well, showing correct reverse banner check, and no blacklisting. DNSQueries.com shows a valid reverse DNS entry as well for us. Outbound emails to these 2 domains continue to sit in the queue. Any ideas or advice would be greatly appreciated. Thanks!

    Read the article

  • IIS 7.5 returning 404 for unknown host names

    - by WaldenL
    This just doesn't seem correct to me, so I'm looking for someone to tell me how I've misconfigured IIS... Configuration is IIS7.5 (2008R2), without SP1. I have IIS 7.5 configured w/several sites. ALL sites have hostnames defined in the bindings, there is NO site w/out a hostname. However, if I request an unknown hostname from the server IIS (technically Microsoft-HTTPAPI/2.0) return a 404 error, not a 400 error. I would expect a 400 (or some other major error) rather than a lowly 404. This causes a problem when I have nginx in front of multiple IISs and want to stop a site so nginx takes it out of rotation. Since IIS still returns a 404 for the request even when there is no active site for that name, nginx doesn't know the server is dead. NB: IIS returns the 404 regardless of whether there is a server, but it's stopped, or there is no server. Thoughts? Solutions? -- Additional info: OK, I added a site on a port other than 80 (5000) and then on a connection to that port asked for a site that doesn't exist, and I get the expected error 400 (Invalid hostname). So, while IIS isn't listening for generic (no host name) connections on port 80 it would seem that something is. Any ideas how to get HTTPSys to dump the list of what it's listening for?

    Read the article

  • ISA 2000 and COD MW2 Steam

    - by twlichty
    OK, so maybe not the "proper use" of network resources, but we enjoy the odd COD game during lunch hours. When we played COD4, we had a dedicated server setup at the back of the server room. With MW2, we need to be able to connect to steam to be able to play multi-player. I've found this support article here: https://support.steampowered.com/kb%5Farticle.php?ref=8571-GLVN-8711 Which outlines all the ports I need to open. I went through and created the following rules in ISA 2000 (I'm stuck with 2000 for now). Protocol Definition: Steam Primary connection: Port 27000, UDP, Send Receive Secondary Connection: Port range 27001-27030 Send Receive Protocol Definition: Steam TCP In Primary connection: 27014, TCP, Inbound Secondary Connection: Port range: 27015-27050, Inbound Protocol Definition: Steam 4380 Primary connection: 4380, UDP, Send Receive When I start steam on my local workstation (I did add an exception to the Vista Firewall to allow steam), the steam client sits on "Updating Steam" for 5 minutes then errors out with: You must connect to the internet first. Any ideas? I assume I missed something. Thanks for your help.

    Read the article

  • Pin the Dock to the top or disable it

    - by Chris Buchholz
    I wonder if it is possible to pin the Mac OS X Dock to the top in Snow Leopard? I see lets of ideas on how to do this when I google for it, and Secrets (the tweaking app) also provide it as an option, but I don't see any of the ways working for me. I guess it must have worked at some point, since people said it did, but I believe this feature might have been removed from Snow Leopard, and therefore does not work for me. Is this so? Is there really no way to pin the Dock to the top of screen? If not, what ways of "getting rid of the dock" can you guys recommend? I have tried with auto-hiding, but my problem is that this will leave a 4px line at the edge of where the Dock is pinned to, that applications wont cover. Thats not ideal for me. As far as I have understood from googling, this line will not appear if the Dock is pinned to the top, hence my question. What other ways do you guys use to get rid of it?

    Read the article

  • Windows 7, Printer is unavailable until PC reboot

    - by Cjs
    We are having a problem that I haven't seen before and can find no answers to online. A desktop running Windows 7 is unable to print using network printers. When the user tries, no matter what printer it is, he get's the following message when using Microsoft Office applications: "Current printer is unavailable. Select another printer." When the end user uses Outlook we get the message: "Printing is not available. There are no printers installed. You can select and configure a printer in Windows Control Panel." Now here is the confusing part, if we reboot the pc it works fine for a little while and then goes back to the same old same old. The printers are working fine for every other user as well so I believe it is the user's machine. If anyone has any ideas please let me know. Edit: I'd like to add in that some people were having luck disabling snmp for the printers. Restarting the print spooler doesn't seem to do anything.

    Read the article

< Previous Page | 619 620 621 622 623 624 625 626 627 628 629 630  | Next Page >