Search Results

Search found 19200 results on 768 pages for 'xp mode'.

Page 621/768 | < Previous Page | 617 618 619 620 621 622 623 624 625 626 627 628  | Next Page >

  • Cisco Catalyst 3750 connected to Cisco ASA 5505 and dropping packets

    - by Bo102010
    (Cross posted from Super User per suggestion there) At the office, I have inherited a network that I am still trying to fully comprehend. I have a problem today with a new connection between: A port on a Cisco Catalyst 3750 [WS-C3750G-48TS-S running C3750-IPSERVICESK9-M version 12.2(53)SE1] A port on a Cisco ASA 5505 [ASA Software version 8.3(2)] The 3750 is home to a Vlan that has a few ports assigned to it. interface Vlan3 description Internal network (172.18.160.0/24) ip address 172.18.160.1 255.255.255.0 I have a host (outside of my control) that needs to be in this VLAN (i.e it must have an address 172.18.160.something/24) that also needs to access the Internet. To accomplish this, I ran a link from the Catalyst (Gi1/0/13) to the ASA (Ethernet 0/5). I configured the Catalyst port like so: interface GigabitEthernet1/0/13 description To ASA, 172.18.160.69 switchport access vlan 3 switchport mode access speed 100 duplex full I configured the ASA like so: interface Vlan1 nameif inside security-level 100 ip address 172.18.160.69 255.255.255.0 interface Ethernet0/5 speed 100 duplex full Then I plugged the host into Ethernet 0/4 on the ASA and instructed its owner to make its default gateway 172.18.160.69. I made a NAT rule in the ASA and set up some rules, and it's able to access the Internet without issue. However, I noticed that the Catalyst reports a ton of packets being dropped toward the ASA. Catalyst3750#show interfaces GigabitEthernet 1/0/13 | include counters|drops Last clearing of "show interface" counters 00:28:13 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 136909347 This is a huge number of drops, since there's not much traffic on this VLAN at all. I tried these things: Make sure speed and duplex agree on both sides (100 Mbps / Full) Set no cdp enable on the Catalyst Gi10/13 Set no keepalive on the Catalyst Gi10/13 Checked for excessive CPU usage on both Checked for excessive traffic on both Am I missing something? Any help would be appreciated.

    Read the article

  • Can't Get Mac Mini to turn on - no screen, no beep, only the fan, power light, and optical drive noi

    - by pibyers
    I have an Intel-based Mac mini mid-2007 (Model A1176). This is the computer my kids use so I don't use it regularly. The computer had been working fine until one day my kids told me that it no longer works. The computer will not boot up. When I turn it on the fan turns, the white power light in the front turns on, and there is a sound that appears to be from the optical drive (rather than hard drive). I don't get anything to the monitor, nor do I get any dings or other start up sounds from the computer. Here is what I've tried thus far to no avail: 1) Swapped out the monitors early on since I figured that was my weak link - no change 2) Reset the PMU - no change 3) Tried to boot up from the System Disk - The mini loaded the dvd into the drive, but nothing else (I can't eject the disk so I can put it back) 3) Start up the computer in target mode connected to another mac - I tried this too, but I never received a chime or the disk show up on the other mac. I'm about out of ideas apart from scraping the computer. Does anyone have any ideas that I can try? Again, nothing has been done to the computer in at least 6 months when I upgraded the RAM. I'm also still on Leopard. Thanks.

    Read the article

  • Samba and Windows 7

    - by John Gaughan
    I built a new computer with the intention of it being primarily a home file server. Here is my setup: one desktop with Windows 7 64 HP one laptop with Windows 7 64 HP one desktop with Kubuntu 11.10 (server) The two desktops use static IPs, and I have hostnames mapped in the HOSTS files on all three systems. I have the same username/password combo on all three systems. I have been trying for a while now to set up Samba so the Windows 7 systems can see and use it. Even if I can get the server to show up, Windows is unable to log in. One of the first things I did was to enable LMv2 authentication, which this version of Samba (3.5.11) supports. The workgroup is set correctly. I can normally see the server, but cannot authenticate. Windows homegroup is turned off. Pinging between machines works fine, and the two Windows 7 systems work together flawlessly. What I am trying to do is set up Samba to use peer to peer networking using NTLM security and user-mode authentication. According to the documentation this is possible, but there are no examples that I could find. In all the googling I have done, I see a lot of people asking how to set this up but it either works for someone else and not for me (no idea what I'm missing), or it doesn't work. Has anyone gotten this to work? Is there a place I could download a smb.conf that is set up to work in this environment?

    Read the article

  • Elevating UAC via .bat file?

    - by jslaker
    Pretty straightforward one that I'm having trouble finding an answer to. serverfault previously helped me with finding a way to automate Windows updates without using WSUS. It's working fantastically, but to run it over the network, you have to first mount a shared drive. That's pretty simple XP since you just mount the drive and run the updater. On Vista and W7, though, this all has to be done with elevated privileges to work correctly. The UAC account can't see network drives mounted by the regular user, so in order to get everything working, I have to mount the share via net use from an escalated shell. I'd like to automate mounting this share and launching the updater via a simple .bat file. I could probably just instruct everybody to right click "Run as Administrator" on the .bat file, but I'd like to keep things as simple as possible and have the .bat automatically prompt the user to escalate their privileges. Since these computers don't belong to us, I can't count on anything like Powershell being installed, so that rules any solution along those lines out and pretty much have to rely on things that would be included in an RTM Vista install. I'm hoping I'm mostly missing something obvious here. :)

    Read the article

  • Batch copy gives errors, xcopy works fine

    - by ndm13
    I am writing a general file backup program. It searches the drive for files matching a set of types and then writes them to a folder on the desktop. I wrote it using xcopy on Windows XP but upon learning that xcopy was deprecated in favor of robocopy in Vista and newer, still wanting to maintain compatibility I decided to switch to the non-deprecated copy. This is where the problems begin. I'm trying to fix the copy routine. I thought I had everything sorted out, but it doesn't copy anything. My output is zero files copied for every iteration. Original Code using xcopy: for /r %%a in (*.bmp *.dds *.gif *.jpg *.jpeg *.png *.psd *.pspimage *.tga *.thm *.tif *.tiff) do ( echo f | xcopy "%%a" "%HOMEDRIVE%%HOMEPATH%\Desktop\LDR\Images\Bitmap\%%~nxa" /q /y /g /c ) Revised (broken) Code using copy: for /r %%a in (*.bmp *.dds *.gif *.jpg *.jpeg *.png *.psd *.pspimage *.tga *.thm *.tif *.tiff) do ( copy "%%a" "%HOMEDRIVE%%HOMEPATH%\Desktop\LDR\Images\Bitmap\%%~nxa" /d /y /z ) Output: The system cannot find the path specified. 0 files copied. I know that it seems everyone uses either xcopy or robocopy but can anyone help with copy? Note: I'm using Batch to keep it very lightweight and command-line accessible.

    Read the article

  • Using AddEncoding x-gzip .gz without actual files

    - by STATUS_ACCESS_DENIED
    With Apache (2.2 and later) how can I achieve the following. I want to transparently compress using GZip encoding (not plain Deflate) the output when a certain file is queried with its name plus the extension .gz, where the .gz version doesn't physically exist on disk. So let's say I have a file named /path/foo.bar and no file foo.bar.gz in the folder to which the URI /path maps, how can I get Apache to serve the contents of /path/foo.bar but with AddEncoding x-gzip ... applied to the (non-existing) file? The rewrite part appears to be easy, but the problem is how to apply the encoding to a non-existent item. The other way around also seems to be simple as long as the client supports the encoding. Is the only solution really a script that does this on the fly? I'm aware of mod_deflate and mod_gzip and it is not what I'm looking for - at least not alone. In particular I need an actual GZIP file and not just a deflated stream. Now I was thinking of using mod_ext_filter, but couldn't bridge the gap between rewriting the name of the (non-existent) file.gz to file on one side and the LocationMatch on the other. Here's what I have. RewriteRule ^(.*?\.ext)\.gz$ $1 [L] ExtFilterDefine gzip mode=output cmd="/bin/gzip" <LocationMatch "/my-files/special-path/.*?\.ext\.gz"> AddType application/octet-stream .ext.gz SetOutputFilter gzip Header set Content-Encoding gzip </LocationMatch> Note that the header for Content-Encoding isn't really needed by the clients in this case. They expect to see actual GZIP files, but I want to do this on-the-fly without caching (this is a test scenario).

    Read the article

  • How can I set Vim to obey accents of my spoken language?

    - by naxa
    When pressing w or e in sentences with accents (written in my native language), such as the first one (marked **) here: **Éj-mélybol fölzengo** - csing-ling-ling - száncsengo. Száncsengo - csing-ling-ling - tél csendjén halkan ring. [1] the characters o, ö, among others [2], make my gVim think they are word-ends so it stops on them (in Normal mode). gVim stops on the positions marked with _ where it shouldn't: Éj-mélyb_ol f_ölzeng_o. I would like to set gVim so it properly handle words even when containing accents and other local characters. But where do I set this? I use it on Win32, vim v 7.3.46. [1] - excerpt of a poem by Weöres Sándor [2] - "others", not mentioned here :) like í, u are also a problem. On the other hand, gVim seems to already work with é and á. gVim version info: VIM - Vi IMproved 7.3 (2010 Aug 15, compiled Oct 27 2010 17:59:02) Included patches: 1-46 Compiled by Bram@KIBAALE Big version with GUI. Features included (+) or not (-): +arabic +autocmd +balloon_eval +browse ++builtin_terms +byte_offset +cindent +clientserver +clipboard +cmdline_compl +cmdline_hist +cmdline_info +comments +conceal +cryptv +cscope +cursorbind +cursorshape +dialog_con_gui +diff +digraphs -dnd -ebcdic +emacs_tags +eval +ex_extra +extra_search +farsi +file_in_path +find_in_path +float +folding -footer +gettext/dyn -hangul_input +iconv/dyn +insert_expand +jumplist +keymap +langmap +libcall +linebreak +lispindent +listcmds +localmap -lua +menu +mksession +modify_fname +mouse +mouseshape +multi_byte_ime/dyn +multi_lang -mzscheme +netbeans_intg +ole -osfiletype +path_extra +perl/dyn +persistent_undo -postscript +printer -profile +python/dyn +python3/dyn +quickfix +reltime +rightleft +ruby/dyn +scrollbind +signs +smartindent -sniff +startuptime +statusline -sun_workshop +syntax +tag_binary +tag_old_static -tag_any_white +tcl/dyn -tgetent -termresponse +textobjects +title +toolbar +user_commands +vertsplit +virtualedit +visual +visualextra +viminfo +vreplace +wildignore +wildmenu +windows +writebackup -xfontset -xim -xterm_save +xpm_w32

    Read the article

  • Cannot Delete Item "Could Not Find This Item" issue

    - by aronchick
    A friend sent a long a file (a .rar) he wanted me to check out for him before he installed it. I downloaded it and unrared it with no problems, but it was full of .exe's instead of the intended contents (fonts) so I advised him to delete it immediately and not use. I then proceeded to do the same, but the folder simply will not delete. Oddly the files went fine, and I never ran anything, but this is what I'm seeing: Could not find this item This is no longer located in C:\Users\This_User\Desktop. verify the item's location and try again. I've tried the following things with no help: Using "Unlocker" to Unlock and delete Using move on reboot and rebooting Using PendMoves (from sysinternals) and rebooting Elevating a cmd line, doing a dir /x to get the short name of the folder, and then del 'shortna~1' Moving the folder to a new folder and then trying to delete the parent folder I'm on Windows 7 RTM, very fresh install. Any thoughts? Update: Just to confirm, I've run Hijack this and half a dozen other malware detectors, and everything came back clean (no extra processes, no other obvious badness). Rebooting in safe mode didn't help either.

    Read the article

  • DNS Resolution doesn't work after uninstalling Cisco VPN & Deterministic Network Enhancer in Win 7

    - by Craig M
    I just upgraded my home PC to Windows 7 Ultimate 32 bit. After trying various methods to get the Cisco VPN client to work, I gave up and decided to just run it in XP mode. The last steps I tried were in this article ( http://social.technet.microsoft.com/Forums/en-US/w7itproappcompat/thread/d880dfe5-7f44-4955-8620-2a9355d8ea8b/ ) After that, I uninstalled the Cisco client and rebooted. I uninstalled the Deterministic Network Enhancer and rebooted again. Both uninstalled successfully, but now I'm not able to resolve any DNS. The only way I can resolve DNS is to reinstall the DNE, reboot, and uninstall the DNE. Then I am able to resolve DNS lookups until I reboot again. Once it's rebooted, no more DNS. Any ideas? Edit: I completely forgot I'd asked this question until harrymc posted his answer. I've since found out that to fix this problem, I need to disable my Local Area Connection and re-enable it. Once I do that I have no trouble making network connections until the next time I reboot at which point I repeat the process. It's annoying, but manageable since I reboot very infrequently.

    Read the article

  • PDF to HTML - batch converter - most reliable and accurate free AND paid for software?

    - by therobyouknow
    I'm look for either a free or paid-for (about 50$/40pounds) BATCH PDF to HTML converter to convert several PDF files at once. Needs to be able to handle vectored and bitmap images within the file, outputting both as jpegs referenced by the html pages. I've tried iorigsoft paid-for PDF to HTML - problems it seems to hang or just go idle, and the stuff it actually converts have broken links - the wrong name is used for constituent chapters as html. Also tried application from intrapdf.com but this crashes near the beginning of the conversion, consitently. Update: intrapdf works on my Windows XP machine but not on my Windows 7 machine. The only glitch is with the framed index contents html - the graphics in the page do not display in the page in the frame - but if you open the frame only in a new tab then you can see them. That might be a browser glitch in chrome only. This solution is good enough for me - given that I've already spent the money (I had spent before I asked) but I can't accept my own answer as this does not work on Windows 7. Looked at opensource tools but they look equally flakey or use old PDF versions. Need it on Windows 7 32bit home. Thoughts?

    Read the article

  • Setting up Windows SBS 2008 network on Xen

    - by samyboy
    I'm trying to install a Windows SBS 2008 server in a Xen environment. The OS is booting fine. Unfortunately I can't figure out how to set up the network settings. Dom0 is a Debian Lenny hosting around 10 virtual servers. Here are the settings I'm using in the hosted Windows SBS: IP address: 10.20.0.8 Network mask: 255.255.0.0 Gateway: 10.20.0.1 Note that during the installation stage, Windows set the net mask at 255.255.255.0 without letting me choose. Gross. Windows SBS tells me I have a "limited connection". I can't ping the gateway nor any other IP except localhost and it's own IP (10.20.0.8). Here is the Xen config file: kernel = '/usr/lib/xen-3.2-1/boot/hvmloader' builder = 'hvm' memory = '4096' device_model='/usr/lib/xen-3.2-1/bin/qemu-dm' acpi=1 apic=1 pae=1 vcpus=1 name = 'winexchange' # Disks disk = [ 'phy:/dev/wnghosts/exchange-disk,ioemu:hda,w', 'file:/mnt/freespace/ISO/DVD1_Installation.iso,ioemu:hdc:cdrom,r' ] # Networking vif = [ 'mac=00:16:3E:0A:D0:1B, type=ioemu, bridge=xenbr0'] # video stdvga=0 serial='pty' ne2000=0 # Behaviour boot='c' sdl=0 # VNC vfb = [ 'type=vnc' ] vnc=1 vncdisplay=1 vncunused=1 usbdevice='tablet' This config is working with others Windows XP domU's. I tried to change the ne2000 values with 0 and 1 with no effect. I am far from having good Windows administration skills so I guess I definitely need some help on this case. Thanks.

    Read the article

  • How to migrate a running KVM (with full disk copy) to another node?

    - by klipz
    I'm doing tests on KVM, and I'd like to see if I can make a hot migration, I mean the virtual machine won't stop running during the migration (but a few seconds of freeze is ok). I use a small cluster for my test : kvm1, kvm2, and kvmnfs. kvm1 and kvm2 runs the virtual machines kvmnfs is a NFS server, and it's mounted on /KVM on both kvm1 and kvm2 To migrate a VM (only RAM in fact) from kvm1 to kvm2, I run the same kvm command on kvm2 (with -incoming tcp:0:4444) that on kvm1, then I use "migrate -d tcp:kvm2:4444" : It works great, since the VM file is common to both machines. Now, I wan't to make a full migration (RAM + disk) of a local VM file (no more NFS) of kvm1 to kvm2. I tried to create an empty file, with touch, on kvm2 and use the same kvm command line + the "-incoming ..."). Then on kvm1 I use "migrate -d tcp:kvm2:4444" : It copies everything, then... the VM fails (any I/O disk gives an I/O error) ! And my VM file on kvm2, the one I created with touch, as still a size of 0 bytes. What am I doing wrong ? What is the exact command to use on kvm2 ? And what is the command to launch, in the monitoring mode, on kvm1 ?

    Read the article

  • Fedora 9 not reconizing hard drive

    - by Andrew Jones
    I am installing Fedora 9 to a PC (specifications at the bottom) and have had a lot of trouble with it recognising the hard drive. To get the Fedora installer to recognize it in the first place I had to pass "ata_generic.all_generic_ide=1 pci=nomsi" to the kernel, after which it installed OK. However, now when I boot the installed OS, I get a "could not find filesystem '/dev/root'" error. I tried passing the same arguments to the kernel at boot as I did when installing but to no avail. I have tried using the default LVM layout and defining manual ones but it made no difference. There is no option in the BIOS to enable AHCI or anything like that, in fact the BIOS is very limited in most respects. I can get into the system by using the installation CD in rescue mode (with those extra kernal parameters) but I'm not sure what to do once in there... Unfortunately using a more recent version of Fedora or even another Linux distribution altogether isn't an option becuase of outside constraints - which is annoying since I know for a fact Ubuntu works fine on this setup. I have not been using Linux that long, so treat me like an idiot - I am one. Any help would be greatly appreciated, thanks! System spec: Intel Atom Z530 CPU @ 1.6 GHz Intel US15W chipset 1 GB DDR2 160 GB SATA harddisk (Samsung HM16HI) 1000 Mbit/s Ethernet port Phoenix BIOS

    Read the article

  • CD-ROM Cant Be Accessed After Installing VMware Tools on VMware Server 2.0.2

    - by Optimal Solutions
    Using VMware Server 2.02, I set up a new VM (Windows XP Pro) applied all of the updates, added Windows addons from the install CD, etc... I got it to a stable point and up through that point I was able to access the CD-ROM drive (E: on my host). What I never did before was install "VMware Tools" and since it claims to give better mouse and video support, I gave it a shot. What it does is it places the install package in a virtual CD-ROM drive. I ran the install, no errors and it wants a reboot. I log back in after reboot and pop in the install CD for Microsoft Office 2003 and I receive the message "Please Insert A Disc Into Drive D:". Drive D: would be the next logical drive after the C: drive where I chose to install the OS. The message box sits there and if I click "Cancel", to return to Windows Explorer, the status bar seems to blink ever 1/2 second - as if its polling for a CD-ROM drive or something. No bangs or exclamations in the Device Manager for any hardware. I had taken a snapshot prior to the VMware Tools install and upon restoring it, the CD-ROM is back. I made copies of two other VMs, installed the VMware Tools on those VMs and both experienced the same issues: Windows 2003 Server and Windows 7 (32-bit). Has anyone seen this issue and know of a fix for this? It would be nice to have the better graphics and better mouse control AND use my CD-ROM drive as well! Thank you.

    Read the article

  • Setting up a localhost mail server on Mac OSX

    - by Thom
    I asked this over on stackoverflow. I would love to be able to test php webapps that require emailing registration info etc. on my mac. I downloaded a version of CommuniGate Pro. I need to mail either to an account inside or outside (whichever is best) of the localhost. Again this would be used for testing purposes to verify and debug my code prior to uploading to a hosting service. Any ideas, help and/or examples would be very much appreciated. If it would be easier I could go over to Windows XP. That would just mean setting up wamp and transfering my files over from the mac side via dropbox. I got the local mailserver to work so I can send emails between accounts. However, I cannot seem to get the php code to work. I know that I am missing something. <?php function email($to, $subject, $body, $headers) { $headers = 'MIME-Version: 1.0' . "\r\n"; $headers .= 'From: <[email protected]>' . "\r\n"; mail($to, $subject, $body, $headers); } ?>

    Read the article

  • Setting up a localhost mail server on Mac OSX

    - by Thom
    I asked this over on stackoverflow. They pointed me here. I would love to be able to test php webapps that require emailing registration info etc. on my mac. I downloaded a version of CommuniGate Pro. I need to mail either to an account inside or outside (whichever is best) of the localhost. Again this would be used for testing purposes to verify and debug my code prior to uploading to a hosting service. Any ideas, help and/or examples would be very much appreciated. If it would be easier I could go over to Windows XP. That would just mean setting up wamp and transfering my files over from the mac side via dropbox. I got the local mailserver to work so I can send emails between accounts. However, I cannot seem to get the php code to work. I know that I am missing something. I see where this has been asked before. I want to add that I am using xampp. In Mac OS 10.6.8. I tried changing the php.ini SMTP command to macintosh-3.local. <?php function email($to, $subject, $body, $headers) { $headers = 'MIME-Version: 1.0' . "\r\n"; $headers .= 'From: <[email protected]>' . "\r\n"; mail($to, $subject, $body, $headers); } ?>

    Read the article

  • Dual boot nt4 and windows 98

    - by ItFinallyWorks
    I am trying to dual boot nt4 and windows 98 se (don't laugh - old computer). I have seen Microsoft's instructions for doing this, but it limits windows 98 to have a Fat16 partition (NT4's NTLDR doesn't understand FAT32) and therefore only 2GB of disk space. I really need it to have more than that. I started with Win 98 (on the 1st partition), repartitioned the disk, then added NT4 on the 2nd partition. NT4 took over the bootloader (as expected), so NT4 boots, but Win 98 doesn't. Right now I am working in VMWare so I can use nonpersistent hard drives (IDE like the real computer) to recover from errors easily. I've tried using XPs NTLDR using the instructions here: http://www.nu2.nu/fixnt4/ , but I got weird errors from NT4 and it never really worked. If XP's NTLDR would work, that should be able to boot both OSes. I've also tried using GRUB. In theory that should work. In fact when booting from super grub disk, it does. But as soon as I install grub to disk, Win 98 boots, but NT 4 blue screens at boot with a 0x0000007b inaccessible_boot_device error (that can be alot of things see MS kb 822051). The incantation I'm using for GRUB 1 is rootnoverify (hd0,1) makeactive chainloader +1 boot So, anybody have some suggestions?

    Read the article

  • USB device goes to "Unknown device" randomly

    - by ILovePaperTowels
    We have a kiosk that uses a bio scanner from m2sys (usb device). It scans your palm to recognize you. Every so often, maybe 1-3 times a day, the bio scanner will become an unknown device. We are unable to see any patterns or commonalities. When we unplug and plug it back in, it becomes available again. We have custom software that uses the bio scanner's software to communicate with it. We've added a crap load of logging on everything but there doesn't seem to be any pattern of when the thing shuts off. We have these devices deployed to multiple locations (100+) and they are all seeing the issues but we can not reproduce it here, at the main office. I've evaluated the software and I don't see anything. I'm thinking it's a driver or hardware issue (but we can't reproduce the issues here in the main office) or maybe environmental interference of some sort like from scan guns, automatic doors, microwaves or something else. Any ideas would be welcome. I'm looking for possible causes of the usb device becoming unknown or ways to figure out what the cause is. no other usb devices have this issue, only the scanner We've contacted the manufacturer and they blame our software We're getting help from Microsoft, but they haven't found anything OS is embedded XP http://www.m2sys.com/palm-vein-reader.htm

    Read the article

  • QNAP NAS 509 (LINUX) - how to unmout busy volume and find physical disk?

    - by Horst Walter
    On my NAS QNAP TS 509 I do have a technical issue. I need to run e2fsck. This works fine for me on md0 (see below), but how can I unmount the busy devices md9 and sda4 in order to do the same. Whenever I try, I fail because the device is busy. [This part is solved, see below] In order to further track down the issue, I'd need to sort out the physical disk to device relationship. How can I find out this, e.g. md0 is a stripped volume on 2 disk (but I need to find out on what physical disk). Remark: As you can easily derive from my questions, I am not a Linux expert, but manage to get along. /dev/ram0 124.0M 94.1M 29.8M 76% / tmpfs 32.0M 80.0k 31.9M 0% /tmp /dev/sda4 310.0M 103.9M 206.1M 34% /mnt/ext /dev/md9 509.5M 39.2M 470.2M 8% /mnt/HDA_ROOT /dev/md0 1.8T 1.4T 444.7G 76% /share/MD0_DATA tmpfs 32.0M 0 32.0M 0% /.eaccelerator.tmp -- Added -- QNAP seems to be based on Busybox. I do not find something like init / telinit / runlevel. At busybox docs it says that I need to run the below. But in /var/service sv is not available. I want to go to single user mode to unmount the devices. # cd /var/service # sv d * # sv u getty* -- Added, thanks A4L -- This QNAP Box runs a special flavor of Linux, so not all SOPs do apply. In my particular case I found a services.sh script, stopping all services. After that the drive could be unmounted. The information passed by A4L is valid and worth reading it, maybe I'll profit from it next time. Links: http://unix.stackexchange.com/questions/19918/umount-device-is-busy and http://unix.stackexchange.com/questions/15024/umount-device-is-busy-why So the unmount issue is solved, still looking for the best option to find the physical to volume mapping.

    Read the article

  • Data recovery on a data HDD (no OS)

    - by aCuria
    I am helping a family member with a dead hard disk. It is a seagate 200Gb 3.5" HDD in one of those old-school external enclosures. The problem was that windows failed to detect the hard disk when plugged in through USB. I removed the hard disk from its enclosure, and plugged it into my desktop PC. The BIOS does detect it upon POST, but unfortunately windows 7 would refuse to boot. It will get stuck on the loading screen with the glowing windows logo. Safe mode doesn't help either. What options do I have before going for some professional data recovery? edit: Someone modified the Title to something completely different from what I was asking, i just changed it back. 1) 2 HDD drives, DiskA(Dead), DiskB(my OS disk) 2) when B is connected to my system, everything works fine 3) when A AND B is connected, failure to boot. POSTs fine, but windows wont load 4) A has NO OS, its PURE data. It came from an EXTERNAL HDD enclosure which doesnt belong to me, and im trying to do data recovery.

    Read the article

  • Getting the most out of a Mac mini as a media center

    - by celebritarian
    Hello! I own an old Mac mini from 2006 (maybe early 2007). It's got an Intel Core Solo 32-bits CPU and 512 MB RAM. 160 GB HDD. The GPU is an integrated chip… Currently, my Mini is sitting under my LCD TV (720p). It's plugged in via a DVI to HDMI cable. It's currently running Leopard. And unfortunately, Snow Leopard can't be installed on a device with less than 1 GB of RAM… So, my Mac mini isn't exactly powerful. Also, it's slow and Mac OS X is not a pleasant experience on my Mini right now. It feels slow and heavy. I want to use my Mac mini as a media center/player. I want to be able to play video files in 720p (H.264, Matroska/MOV files). So basically, playing high-def videos is all I want to do with my Mini. What OS should I install? Stick to OS X? Optimize for video playback? Or should I install another OS — like Win XP, Ubuntu or any other Linux dist? Then, will my Mini be able to play 720p videos smoothly, even though the CPU and GPU aren't that powerful and with the limit of 512 MB of RAM? Appreciate all help. Thanks in advance!

    Read the article

  • .htm pages working but .aspx pages throwing errors

    - by Mike
    Our site has thousands of visitors per day but we've been receiving reports from some of our members that they are able to hit our main page, presumably because it's a .htm page, but when they click off to a .aspx page, they get an error. I've done as much research as I know how and here is what I have come up with: - We have not made any changes to IIS on our server in months. - We have a couple of customers that have been willing to work with us and provide information about their system. One customer is running Vista, the other is running XP. - We had one of the customers test both Firefox and MSIE. She gets same error in both. - One customer said, "We were able to post the profile and searched on available jobs and it worked w/ Firefox for a day, then it just quit working...we did not change any settings to Firefox after we posted the profile." - We asked the customer to clear their cache and try again. They responded with, "We just cleared the cache and got the same error; btw, I periodically clear the cache -- almost every day." Summary We have thousands of customers that hit our site with no problem. We can't reproduce these errors. These customers are getting the same error in different browsers. They are only getting the error on .aspx pages. They still get the error after clearing their cache. We would appreciate any thoughts on what other questions we could ask these customers or thoughts on how we can further troubleshoot this problem.

    Read the article

  • Windows 7 hangs while loading desktop

    - by Joshua
    I am facing a weird problem. My computer hangs while loading the desktop, and only the background shows up; no icons or bars load. If I power the system on and off about 4-6 times, I may be able to use it normally. The desktop loads normally after rebooting or in safe mode; this only occurs when I start the system normally. I've tried several things to fix it, such as removing all start-up items, but it still doesn't solve the problem. What should I do? I found three major errors in Event Viewer: Source: Microsoft-Windows-DistributedCOM Level: Error DCOM got error "1084" attempting to start the service WSearch with arguments "" in order to run the server: {7D096C5F-AC08-4F1F-BEB7-5C22C517CE39} Source: Microsoft-Windows-DistributedCOM Level: Error DCOM got error "1084" attempting to start the service WSearch with arguments "" in order to run the server: {7D096C5F-AC08-4F1F-BEB7-5C22C517CE39} Source: Service Control Manager Level: Error The Network List Service service depends on the Network Location Awareness service which failed to start because of the following error: The dependency service or group failed to start.

    Read the article

  • Problem importing pictures from a digital camera with Windows 7

    - by snark
    Hi, Since I'm using Windows 7 (Beta, then RC, now RTM), I have issues when I download pictures from my digital cameras. It happens with my 2 cameras: a Canon Powershot S2 IS and a Canon Ixus 80 IS. When I plug a camera (any of them) to a USB port and switch it on in Play mode, the Autoplay function of Windows 7 starts with this screen: I select "Import pictures and videos" to call the native Windows 7 tool. It searches a bit for pictures to download from the camera and starts the transfer. However, during the transfer, I often get errors like this one: If I use "Try again", it works fine the second time and the picture is retrieved correctly. It's very annoying when it happens 20 or 30 times in a 500-picture download. I cannot leave it running standalone, as I have to watch for the errors and click on "Try again". Any idea what is causing these errors? I tried changing the USB port (normally the cameras are connected via a USB hub but it happens also when I connect them directly to a MB USB port) and the USB cable, but no success. I also checked the SD card by connecting them with a card reader and running a ChkDsk on them but it found no errors on the cards. Update: No problem when I copy the pictures manually with the Windows Explorer. And no problem either when I access the card with a reader. The builtin import tool of Windows is convenient as it sorts the pictures automatically by date (1 folder per day). And this is the way I sort my pictures

    Read the article

  • Windows Server 2008 R2 install reboots unexpectedly during "Completing installation" phase

    - by knda
    I am attempting to install Windows Server 2008 R2 onto a Cisco UCS C201 M2 rack mounted server but am having major difficulties and wondering if anyone has some insight or items they could recommend for me to look at to get this one resolved. Installation is being attempted via the Cisco remote console (using CIMC's Virtual dvd-rom).. following the first phase of Setup where the installation files are copied to the target hard drive, then a reboot occurs to load Setup from the HDD, mid-way in the "Completing Installation" phase the system then reboots unexpectedly. System configuration Cisco UCS C201 M2 (2RU rack mounted server) 16GB RAM, 2x 73GB 15K SAS, 4x 300GB 10k SAS Add-on cards - Intel quad-port GigE card (no fibre channel cards) Storage - LSI MegaRAID SAS 9261-8i. onboard SATA is disabled (no SATA drives connected) KVM - Belkin No physical DVD-ROM.. :( I have... Run memtest86+, no RAM faults Disabled/enabled SATA support (BIOS) Attempted install from USB DVD-ROM, no effect Attempted unattended install scripted via Cisco Configuration Manager DVD provided Removed Belkin KVM in case that was causing drama Discovered that the Cisco website is "awesome" for searching for PDFs/Drivers cough, reverted back to Google Downloaded latest LSI drivers from LSI's site and used during Server 2008 install checked Windows ISO against checksum's from MS site checked Windows ISO by using it for an install in a VM Running out of ways to troubleshoot this as I am not sure how to enable any sort of 'verbose' mode during the setup process. Next step I have planned is to remove the Intel NIC and try the installation again.. Edit: Problem was the "Cisco INTEL QUAD PT GBE" (1000/PT) .. will have to see if this card is faulty or if it's just drivers.. thanks for the help.

    Read the article

< Previous Page | 617 618 619 620 621 622 623 624 625 626 627 628  | Next Page >