Search Results

Search found 18151 results on 727 pages for 'upside down'.

Page 639/727 | < Previous Page | 635 636 637 638 639 640 641 642 643 644 645 646  | Next Page >

• Windows 7 laptop constantly dropping internet connection

  - by Corbin Holbert

  I have scoured the web for an answer and failed to find one. I am using a Toshiba Satellite laptop running Windows 7 64-Bit. I have the computer connected via Wifi. Now, I am no beginner with the Internet, or anything related to computers, as I have grown up teaching everyone around me how to use computers, and went to college for IT. Everything on my network works flawlessly at all times, except for this evil laptop. The worst part is that I fixed this once before a few years back and recently had to replace the hard drive and re-install the OS, but cannot for the life of me remember what I did to make this problem go away. I am in my browser, connected to the Internet. I click a link. Suddenly no internet access. All I do is click down on the WiFi connection in the task bar, disconnect and reconnect immediately. Internet is back the moment I hit "connect." I have read many people had the same issues as I am having, but they all had triggers or other network issues. I have no trigger (this happens literally five to six times per minute no matter what I am doing) and I have no problems with my router, modem, or any other devices or computers on said network. As I am a web designer, and like to test my work live at every turn- this is going to result in this laptop being in pieces if I can't get it fixed soon. If more info is needed, let me know and I will provide. Thanks for any help offered! EDIT: Network Card: Realtek RTL8188CE Wireless LAN 802.11n PCI-E NIC Network state reads as "No Internet Access" when the problem first occurs, then magically I have Internet access for about ten seconds once I disconnect and reconnect. I have turned off IPV6, I have turned off power saving options for the network adapter, no viruses. Any new ideas? Also, I had to disconnect and reconnect four times just to get to this edit screen- and will likely have to do the same just to post it- it's that bad.

  Read the article

• Cannot exit X server, restart, shutdown or drop to tty when VGA monitor active

  - by terdon

  I have a strange problem. If I connect an external VGA monitor to my laptop, exiting the X environment in any way crashes the computer. For example, say I am working with my two monitors (the laptop's and one connected to my VGA port) active. Hitting Ctrl+Alt+F Key should take me down to a tty. What actually happens is that the VGA screen goes blank, as you would expect, but the laptop screen, although still on, shows nothing. I know the screen is on because it is slightly more illuminated than when it is off. When in this state, I can do nothing to regain access to the machine. I have tried: Ctrl+F Key (and even Ctrl+Alt+F Key, just in case) combinations and none seem to have any effect. Ctrl+Alt+Del : Nothing Magic SysRq key: Nothing Blindly typing my username and password and trying to reboot/shutdown or restart GDM or MDM: Nothing The only thing that works is a hard reset. The exact same behavior occurs when kiling the X server through Ctrl+Alt+Backspace, rebooting or shutdown. There is no difference if I reboot/shutdown/log out using the WM's graphical menu or if I use the shutdown or rebootcommands. It is also not WM-dependent. I have the same problem using Cinnamon, Gnome 3, MATE and xfce4. It is, however, VGA dependent. I have tried connecting another VGA monitor and have the same problem. I do not, however, have this problem if a screen is connected to the DisplayPort. It is, therefore, a VGA specific issue. To make things even stranger, this only occurs when both screens are active. If either the laptop screen or the VGA monitor is inactive the problem goes away. Finally, this problem arose when I installed the latest Linux Mint Debian (LMDE). It did not occur with the previous release of LMDE. I am not sure what has changed since I used the same kernel version in both releases (I had upgraded the kernel while on the previous release) and, I think, the same nvidia drivers. Oh, and yes, I have updated the nvidia driver. Hardware: Dell M4500 laptop CPU: Intel Core i7 RAM: 8GB Graphics: nVidia GT216 [Quadro FX 880M] Software: LMDE, kernel 3.2.0-2-amd64 Xorg: 1.11.4 nVidia kernel: 295.20-1+3.2.9-1 Possibly relevant files: /var/log/Xorg.0.log ~/.xsession-errors Does anyone have any ideas how to fix this? Thanks in advance for any help.

  Read the article

• Need help making site available externally

  - by White Island

  I'm trying to open a hole in the firewall (ASA 5505, v8.2) to allow external access to a Web application. Via ASDM (6.3?), I've added the server as a Public Server, which creates a static NAT entry [I'm using the public IP that is assigned to 'dynamic NAT--outgoing' for the LAN, after confirming on the Cisco forums that it wouldn't bring everyone's access crashing down] and an incoming rule "any... public_ip... https... allow" but traffic is still not getting through. When I look at the log viewer, it says it's denied by access-group outside_access_in, implicit rule, which is "any any ip deny" I haven't had much experience with Cisco management. I can't see what I'm missing to allow this connection through, and I'm wondering if there's anything else special I have to add. I tried adding a rule (several variations) within that access-group to allow https to the server, but it never made a difference. Maybe I haven't found the right combination? :P I also made sure the Windows firewall is open on port 443, although I'm pretty sure the current problem is Cisco, because of the logs. :) Any ideas? If you need more information, please let me know. Thanks Edit: First of all, I had this backward. (Sorry) Traffic is being blocked by access-group "inside_access_out" which is what confused me in the first place. I guess I confused myself again in the midst of typing the question. Here, I believe, is the pertinent information. Please let me know what you see wrong. access-list acl_in extended permit tcp any host PUBLIC_IP eq https access-list acl_in extended permit icmp CS_WAN_IPs 255.255.255.240 any access-list acl_in remark Allow Vendor connections to LAN access-list acl_in extended permit tcp host Vendor any object-group RemoteDesktop access-list acl_in remark NetworkScanner scan-to-email incoming (from smtp.mail.microsoftonline.com to PCs) access-list acl_in extended permit object-group TCPUDP any object-group Scan-to-email host NetworkScanner object-group Scan-to-email access-list acl_out extended permit icmp any any access-list acl_out extended permit tcp any any access-list acl_out extended permit udp any any access-list SSLVPNSplitTunnel standard permit LAN_Subnet 255.255.255.0 access-list nonat extended permit ip VPN_Subnet 255.255.255.0 LAN_Subnet 255.255.255.0 access-list nonat extended permit ip LAN_Subnet 255.255.255.0 VPN_Subnet 255.255.255.0 access-list inside_access_out remark NetworkScanner Scan-to-email outgoing (from scanner to Internet) access-list inside_access_out extended permit object-group TCPUDP host NetworkScanner object-group Scan-to-email any object-group Scan-to-email access-list inside_access_out extended permit tcp any interface outside eq https static (inside,outside) PUBLIC_IP LOCAL_IP[server object] netmask 255.255.255.255 I wasn't sure if I needed to reverse that "static" entry, since I got my question mixed up... and also with that last access-list entry, I tried interface inside and outside - neither proved successful... and I wasn't sure about whether it should be www, since the site is running on https. I assumed it should only be https.

  Read the article

• SSD Fresh Does Not Start

  - by Jim Fell

  I recently installed a new 60GB SSD as my primary hard drive and re-installed Windows 7 Professional 64-bit. I then installed SSD Fress from Abelssoft to optimize Windows to run on the SSD. It seemed to install okay, but when I try to run the utility, its splash screen appears briefly before it quietly closes. No errors are displayed; the utility just fails to launch. I have run SSD Fresh on another SSD-equipped Windows 7 Pro x64 computer in the past without any problems. Does anyone know what might be preventing the program from running? I tried shutting down the Spybot Resident and disabling the firewall and virus scanner with no luck. I also tried running the tool as administrator; I even tried reinstalling it, running the installer as administrator. No luck. Every time I try to launch the program the Event Viewer logs this same set of errors: Error 4/2/2012 11:35:44 PM Application Error 1000 (100) Error 4/2/2012 11:35:43 PM .NET Runtime 1026 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None For those who are interested, here is my system configuration: ASRock M3A770DE AM3 AMD 770 ATX AMD Motherboard AMD Athlon II X3 455 Rana 3.3GHz Socket AM3 95W Triple-Core Desktop Processor ADX455WFGMBOX G.SKILL Value Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) Desktop Memory Model F3-10600CL9D-8GBNT Mushkin Enhanced Chronos Deluxe MKNSSDCR60GB-DX 2.5" 60GB SATA III Synchronous MLC Internal Solid State Drive (SSD) (Primary/Boot HD) Western Digital Caviar Blue RFHWD1600AAJS 160GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive (Secondary HD) Sony Optiarc CD/DVD Burner Black SATA Model AD-7261S-0B LightScribe Support RAIDMAX RX-850AE 850W ATX12V v2.3 / EPS12V SLI Certified CrossFire Ready 80 PLUS GOLD Certified Modular Active PFC Power Supply ASUS HD7850-DC2-2GD5 Radeon HD 7850 2GB 256-bit GDDR5 PCI Express 3.0 x16 HDCP Ready CrossFireX Support Video Card Asus ML228H 21.5" Full HD LED BackLight LED Monitor Slim Design (x3)

  Read the article

• Critique My Backup and Storage Plan

  - by MetaHyperBolic

  My current storage (RAID-1 off of a hardware RAID card) and backup (a spare drive) solutions for my home network are inadequate. I have too much data scattered on various one-off drives. It is time to evolve. Backups seem simple enough, at least: lots of big drives. However, I am bewildered by the number of choices for small home storage. The Drobo S looks appealing. So does the ReadyNAS. I am not looking for bunches of shiny features, I'm mostly interested in reliability. I am not interested in building Yet Another PC to create a file server or doing something in the cloud, or whatever. I'm stupid, so I am keeping it simple. Requirements for Main Volume: Starting working space roughly 2TB, with options for growth up to 5TB RAID or something RAID-like with at least one parity drive eSATA II for speed during backups Ability to shut down gracefully when alerted of low power by a UPS Optional but Desirable: Will take 2TB drives now with options for the larger 3TB drives coming in 2010-2011 Optional but Desirable: : RAID-6 or something similar, with two parity drives Optional but Desirable: : Hot spare Ethernet connection not required, as the volume will be shared via the same machines which runs my home print server Backups: Backup performed via ROBOCOPY in mirror mode to an external hard drive via a eSATA II connection. Start with rotating between two external 2TB hard drives, will go up to six external 2TB drives. Start with a weekly backup, move to a bi-weekly backup as more drives are added. Move to 3TB drives as the size of my main volume increases. Backup drives will be stored on an off-site location. Hard drives: I plan on buying all of the same model, but different batches from different vendors. I found a "burn-in" utility with which I can pound away on the drives for a couple of weeks before adding them to the backup pool or the main volume. I estimate that I am looking at roughly $1,500 to start, once I start throwing in two TB drives for backup and four for storage. So, are there any obvious flaws in my plan? What have I overlooked? Any suggestions for the storage device for my main volume that fits my requirements? Or do I just keep it simple, 2 drives in RAID-1, then perform due diligence with my backups, accepting that I will have to buy a whole new unit when my data grows past 2TB?

  Read the article

• Windows XP machine not seeing external FAT32 partitions correctly

  - by Rob_before_edits

  About 8 months ago my Windows XP machine stopped being able to see FAT32 external drives when I plug them in... mostly. I will explain... It happens with all my FAT32 drives, whether they be unpowered external hard drives, powered external hard drives, SDHC cards plugged directly into the machine's card reader, or SDHC cards plugged in via a separate USB card reader. All of these drives/cards used to work fine on this machine. They all stopped working at about the same time. NTFS volumes are not affected. If I plug in NTFS external drives they are recognized right away. I even have one external drive with two partitions on it, one is NTFS which is recognized, the other is FAT32, which is not recognized. If I attach a FAT32 drive, then reboot, then the drive almost always becomes visible to the machine after the reboot. Sometimes I can plug in a FAT32 drive and it works right away. Not often though. I'd say I get lucky more often with SDHC cards than hard drives. I'm developing a theory that I only get lucky with hard drives if I'm running Acronis Disk Director when I plug them in, though that usually doesn't work either - I need more data here, this may be a red herring. Getting lucky with a hard drive is really rare, usually I have to reboot. When a FAT32 is recognized, either because I got lucky or because I rebooted, I can almost never safely disconnect it. It tells me "The device 'Generic volume' cannot be stopped right now. Try stopping the device again later". I can't seem to get around this. IIRC, I've tried closing every open window, and still no luck. Since I care about my data usually the only way to disconnect a FAT32 drive is to shut down the machine. As you can imagine, two reboots just to read a drive is getting pretty old... When the machine fails to see a FAT32 drive it usually comes up with the appropriate drive letter and the words "Local Disk" in Windows Explorer instead of the correct partition name. If I click on it I get "J:\ is not accessible. The parameter is incorrect." Before this problem arose I always clicked the "safely remove" button for everything, including SDHC cards where I think it's not necessary. I've known for a long time that this is the correct procedure for hard drives, so I don't think failing to do this was the cause of this problem (before someone asks :) Any answers or suggestions most welcome.

  Read the article

• Gateway GT5220 Boot/POST Failure

  - by John Rudy

  I have a Gateway GT5220 I'm troubleshooting. It is, in fact, the machine I just gave my father for his birthday a couple months ago. (Prior to that, it was my home PC. My home PC is now the MacBook on which I'm writing this.) Before going any further, I suspect that the answer will be, "It's worse than that, it's dead, Jim, it's dead, Jim, it's dead, Jim." At least, mobo and/or CPU. The initial symptoms were as follows: Turn on power All fans fire up (thus making it so I can't hear if the hard drive is spinning or not, nor are my hands sensitive enough anymore to feel it) No LEDs remained lit on the front panel. (Initially, the hard drive indicator flashed briefly.) No beep, no video, no nothing. Following some advice I found here, I tried to "drain the stored power." After following those steps, the new symptoms were: Turn on power All fans fire up The front panel LEDs remained lit! After about 20, maybe 30 seconds, we had video! Sort of. We got to the Gateway splash/POST screen, which appeared thoroughly corrupted. How corrupted? Well, I imagine it's what a POST screen would look like after reading the wrong passage out of the Necronomicon: It stayed there. I gave it at least 5, maybe 6 minutes, and it didn't move. So I shut her down, started her up again, and now (this is where we currently stand, symptomatically) we have this: Turn on power All fans fire up The front panel LEDs remain lit No video, no beep, no nothing. I'm a software guy; haven't done real hardware troubleshooting in years. My gut tells me that the mobo and/or CPU is fried, and unfortunately my gut didn't get to be as big as it is being wrong all the time. :( In addition to the link above, I have read all of the following (trying to save you some LMGTFY trouble): Gateway Support POST Error Messages and Handling About a zillion (useless) POST beep code sites A kioskea.net post indicating that most likely we're at what I consider "total loss" (mobo and/or CPU) My questions: Are there any conditions other than mobo/CPU that could cause symptoms like these? Is it worth my time to try the next hardware troubleshooting step?(IE, remove all non-critical hardware from the machine, try to boot, systematically replace one by one until we find the failing component) Which mobos will fit in the Gateway GT5220 case (with rear ports correctly aligned)? (Why this is not a dupe: I wouldn't have posted this question if it hadn't been for the funkadelic possessed video display on the one occasion we got video out. I think that justified this not being an exact dupe. Of course, if the community overrules, I will understand.)

  Read the article

• Postmaster uses excessive CPU and Disk Writes

  - by wolfcastle

  using PostgreSQL 9.1.2 I'm seeing excessive CPU usage and large amounts of writes to disk from postmaster tasks. This happens even while my application is doing almost nothing (10s of inserts per MINUTE). There are a reasonable number of connections open however. I've been trying to determine what in my application is causing this. I'm pretty newb with postgresql, and haven't gotten anywhere so far. I've turned on some logging options in my config file, and looked at connections in the pg_stat_activity table, but they are all idle. Yet each connection consumes ~ 50% CPU, and is writing ~15M/s to disk (reading nothing). I'm basically using the stock postgresql.conf with very little tweaks. I'd appreciate any advice or pointers on what I can do to track this down. Here is a sample of what top/iotop is showing me: Cpu(s): 18.9%us, 14.4%sy, 0.0%ni, 53.4%id, 11.8%wa, 0.0%hi, 1.5%si, 0.0%st Mem: 32865916k total, 7263720k used, 25602196k free, 575608k buffers Swap: 16777208k total, 0k used, 16777208k free, 4464212k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 17057 postgres 20 0 236m 33m 13m R 45.0 0.1 73:48.78 postmaster 17188 postgres 20 0 219m 15m 11m R 42.3 0.0 61:45.57 postmaster 17963 postgres 20 0 219m 16m 11m R 42.3 0.1 27:15.01 postmaster 17084 postgres 20 0 219m 15m 11m S 41.7 0.0 63:13.64 postmaster 17964 postgres 20 0 219m 17m 12m R 41.7 0.1 27:23.28 postmaster 18688 postgres 20 0 219m 15m 11m R 41.3 0.0 63:46.81 postmaster 17088 postgres 20 0 226m 24m 12m R 41.0 0.1 64:39.63 postmaster 24767 postgres 20 0 219m 17m 12m R 41.0 0.1 24:39.24 postmaster 18660 postgres 20 0 219m 14m 9.9m S 40.7 0.0 60:51.52 postmaster 18664 postgres 20 0 218m 15m 11m S 40.7 0.0 61:39.61 postmaster 17962 postgres 20 0 222m 19m 11m S 40.3 0.1 11:48.79 postmaster 18671 postgres 20 0 219m 14m 9m S 39.4 0.0 60:53.21 postmaster 26168 postgres 20 0 219m 15m 10m S 38.4 0.0 59:04.55 postmaster Total DISK READ: 0.00 B/s | Total DISK WRITE: 195.97 M/s TID PRIO USER DISK READ DISK WRITE SWAPIN IO> COMMAND 17962 be/4 postgres 0.00 B/s 14.83 M/s 0.00 % 0.25 % postgres: aggw aggw [local] idle 17084 be/4 postgres 0.00 B/s 15.53 M/s 0.00 % 0.24 % postgres: aggw aggw [local] idle 17963 be/4 postgres 0.00 B/s 15.00 M/s 0.00 % 0.24 % postgres: aggw aggw [local] idle 17188 be/4 postgres 0.00 B/s 14.80 M/s 0.00 % 0.24 % postgres: aggw aggw [local] idle 17964 be/4 postgres 0.00 B/s 15.50 M/s 0.00 % 0.24 % postgres: aggw aggw [local] idle 18664 be/4 postgres 0.00 B/s 15.13 M/s 0.00 % 0.23 % postgres: aggw aggw [local] idle 17088 be/4 postgres 0.00 B/s 14.71 M/s 0.00 % 0.13 % postgres: aggw aggw [local] idle 18688 be/4 postgres 0.00 B/s 14.72 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle 24767 be/4 postgres 0.00 B/s 14.93 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle 18671 be/4 postgres 0.00 B/s 16.14 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle 17057 be/4 postgres 0.00 B/s 13.58 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle 26168 be/4 postgres 0.00 B/s 15.50 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle 18660 be/4 postgres 0.00 B/s 15.85 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle

  Read the article

• umount bind of stale NFS

  - by Paul Eisner

  i've got a problem removing mounts created with mount -o bind from a locally mounted NFS folder. Assume the following mount structure: NFS mounted directory: $ mount -o rw,soft,tcp,intr,timeo=10,retrans=2,retry=1 \ 10.20.0.1:/srv/source /srv/nfs-source Bound directory: $ mount -o bind /srv/nfs-source/sub1 /srv/bind-target/sub1 Which results in this mount map $ mount /dev/sda1 on / type ext3 (rw,errors=remount-ro) # ... 10.20.0.1:/srv/source on /srv/nfs-source type nfs (rw,soft,tcp,intr,timeo=10,retrans=2,retry=1,addr=10.20.0.100) /srv/nfs-source/sub1 on /srv/bind-target/sub1 type none (rw,bind) If the server (10.20.0.1) goes down (eg ifdown eth0), the handles become stale, which is expected. I can now un-mount the NFS mount with force $ umount -f /srv/nfs-source This takes some seconds, but works without any problems. However, i cannot un-mount the bound directory in /srv/bind-target/sub1. The forced umount results in: $ umount -f /srv/bind-target/sub1 umount2: Stale NFS file handle umount: /srv/bind-target/sub1: Stale NFS file handle umount2: Stale NFS file handle Here is a trace http://pastebin.com/ipvvrVmB I've tried umounting the sub-directories beforehand, find any processes accessing anything within the NFS or bind mounts (there are none). lsof also complains: $ lsof -n lsof: WARNING: can't stat() nfs file system /srv/nfs-source Output information may be incomplete. lsof: WARNING: can't stat() nfs file system /srv/bind-target/sub1 (deleted) Output information may be incomplete. lsof: WARNING: can't stat() nfs file system /srv/bind-target/ Output information may be incomplete. I've tried with recent stable Linux kernels 3.2.17, 3.2.19 and 3.3.8 (cannot use 3.4.x, cause need the grsecurity patch, which is not, yet, supported - grsecurity is not patched in in the tests above!). My nfs-utils are version 1.2.2 (debian stable). Does anybody have an idea how i can either: force the un-mount some other way? (any dirty trick is welcome, data loss or damage neglible at this point) use something else instead of mount -o bind? (cannot use soft links, cause mounted directories will be used in chroot; bindfs via FUSE is far to slow to be an option) Thanks, Paul Update 1 With 2.6.32.59 the umount of the (stale) sub-mounts work just fine. It seems to be a kernel regression bug. The above tests where with NFSv3. Additional tests with NFSv4 showed no change. Update 2 We have tested now multiple 2.6 and 3.x kernels and are now sure, that this was introduced in 3.0.x. We will fille a bug report, hopefully they figure it out.

  Read the article

• How do I troubleshoot root cause of a hung windows (2003) server?

  - by GregW

  I have a pair of Windows (2003 Server) servers both running MS SQL Server (2008 EE) that each hang every few months. This has been occurring intermittently :( for the past 15 months pretty much since we started using the servers. The symptoms are as-follows: I cannot remote desktop in to troubleshoot; when I attempt to, I get stuck on a blank black screen and am never offered a login prompt I can still ping the servers I can still open a SQL connection to the server, and, CURIOUSLY/BIZARRELY, when I do a "select getdate()", the time it returns appears to be stuck on the exact fraction of a second when (I presume) the server hung. Repeated attempts to do "select getdate()" keep getting that same date, suggesting that the clock is frozen. Filesharing attempts to connect to the hung server fail with the error message: "\ServerName is not accessible. You might not have permissions to use this network resource. Contact the administrator of this server to find out if you have access permissions. The server's clock is not synchronized with the primary domain controller's clock." This is consistent with a frozen clock. Post-reboot, if I investigate the Windows Event Viewer logs, I can see many security accesses (coming from me and others) that I recognize were login attempts during the "down" period, but all of them in the security log are associated with that same timestamp of when the server hung. This also suggests the clock is frozen. There is not a clear cause in the Application or System event logs. I have a local Admin account on the server and am in the process of getting a domain-credentialed Admin account for better remote admin access. HP is supposed to be supporting these machines and has some low-level ILO2 access but they seem incapable of finding the root cause. A reboot will "fix" the problem but I would like to get to the root cause and solve the issue. Has anyone ever seen something like this odd clock behavior?! (If it were just one server I'd perhaps say a bad hardware clock, but two?) Can anyone advise me on what I should try to troubleshoot this sort of situation to find the root cause (or what I should tell HP to try?)

  Read the article

• Malware - Technical anlaysis

  - by nullptr

  Note: Please do not mod down or close. Im not a stupid PC user asking to fix my pc problem. I am intrigued and am having a deep technical look at whats going on. I have come across a Windows XP machine that is sending unwanted p2p traffic. I have done a 'netstat -b' command and explorer.exe is sending out the traffic. When I kill this process the traffic stops and obviously Windows Explorer dies. Here is the header of the stream from the Wireshark dump (x.x.x.x) is the machines IP. GNUTELLA CONNECT/0.6 Listen-IP: x.x.x.x:8059 Remote-IP: 76.164.224.103 User-Agent: LimeWire/5.3.6 X-Requeries: false X-Ultrapeer: True X-Degree: 32 X-Query-Routing: 0.1 X-Ultrapeer-Query-Routing: 0.1 X-Max-TTL: 3 X-Dynamic-Querying: 0.1 X-Locale-Pref: en GGEP: 0.5 Bye-Packet: 0.1 GNUTELLA/0.6 200 OK Pong-Caching: 0.1 X-Ultrapeer-Needed: false Accept-Encoding: deflate X-Requeries: false X-Locale-Pref: en X-Guess: 0.1 X-Max-TTL: 3 Vendor-Message: 0.2 X-Ultrapeer-Query-Routing: 0.1 X-Query-Routing: 0.1 Listen-IP: 76.164.224.103:15649 X-Ext-Probes: 0.1 Remote-IP: x.x.x.x GGEP: 0.5 X-Dynamic-Querying: 0.1 X-Degree: 32 User-Agent: LimeWire/4.18.7 X-Ultrapeer: True X-Try-Ultrapeers: 121.54.32.36:3279,173.19.233.80:3714,65.182.97.15:5807,115.147.231.81:9751,72.134.30.181:15810,71.59.97.180:24295,74.76.84.250:25497,96.234.62.221:32344,69.44.246.38:42254,98.199.75.23:51230 GNUTELLA/0.6 200 OK So it seems that the malware has hooked into explorer.exe and hidden its self quite well as a Norton Scan doesn't pick anything up. I have looked in Windows firewall and it shouldn't be letting this traffic through. I have had a look into the messages explorer.exe is sending in Spy++ and the only related ones I can see are socket connections etc... My question is what can I do to look into this deeper? What does malware achieve by sending p2p traffic? I know to fix the problem the easiest way is to reinstall Windows but I want to get to the bottom of it first, just out of interest. Edit: Had a look at Deoendency Walker and Process Explorer. Both great tools. Here is a image of the TCP connections for explorer.exe in Process Explorer http://img210.imageshack.us/img210/3563/61930284.gif

  Read the article

• Configuring Windows 2003 As A Router

  - by Sean M

  I am trying to configure a Windows 2003 server to act as a router, so that the two subnetworks that I'm dealing with can communicate with one another without NAT. I am mostly sure that I have configured Windows 2003 incorrectly, and I'm finding it very difficult to drill down through Google results to something helpful. I have a 192.168.1.0/24 network that is my "production" network (in the sense that I'm in trouble if I screw it up) and a 10.0.0.0/8 network that is my test network. The 192.168.1.0 network is ruled by a gateway whose routing table looks like this (my address redacted): The Windows 2003 server, "prime," is multihomed. Its network adapters are at 192.168.1.122, (as seen above), 10.0.0.1, and 10.0.0.2. I added the Routing and Remote Access role to it, and enabled LAN routing. I do not have it using RIP or other routing protocols. Its current routing table is shown below. To me, it looks like all of the right routes are there for traffic to pass between the 192.168.1.0 network and the 10.0.0.0 network. However, traffic does not pass. The 10.0.0.11 and .12 clients cannot be contacted from the 192.168.1.0 network. When I use traceroute to try to get to them, the trace gets to the Windows 2003 server's 192.168.1.122 address, then produces nothing but "* * *" timeouts. When I try to traceroute to 192.168.1.1 from a 10.0.0.0-network client, I get "destination host unreachable." However, I know that the routing is working at least a little, because from the 192.168.1.0 network, I can connect to the Windows server just fine by referring to it as 10.0.0.1. What static routes would allow me to contact 10.0.0.11 and .12 from the 192.168.1.0 network? Is it possible to tell the Windows server "since you are a DHCP/DNS server, you already know routes to get to machines that are getting IP addresses from you, please add those to your routing table" ? Will using RIP or OSPF on the Windows server actually be helpful in this situation?

  Read the article

• DVD Drive Failing on Windows 7

  - by Seth Spearman

  I have x64 Windows 7 running on an ASUS M50VM. The DVD drive works completely unreliably if not at all. But the story is not that simple so bear with me...here are the gory details. When I first got the machine it came with Windows XP and I upgraded it to Windows Vista X64 and the DVD worked fine. When Windows 7 RC2 came out I tried it on a Virtual Machine and I liked it so much that I upgraded the machine to Win7 RC1. The DVD worked fine. Of course, RC1 was going to start spontaneously rebooting, so when Windows 7 was released I DID A CLEAN INSTALL of Windows 7. Just to clarify...by clean install I mean I did a FORMAT of the HARD DRIVE and INSTALLED it from scratch. EVER since then the DVD mostly doesn't work. I can sometime read from disk but that will often hang. (Please see my description below of HANG for details.) CD or DVD writes ALWAYS fail with a HANG (I have done a successful write only one time.) Here is what I mean by HANG... *Explorer Window is unresponsive. *Any software accessing the DVD drive is unresponsive. *The DVD tray will not eject. *Using a paper clip will eject but the disk is usually spinning real hard. *Attempting to shut down windows will fail. I have waited as long as ten minutes but the whole OS seems to hang. I do a hard shutdown. *Sometimes accessing the DVD (when it does not cause a HANG) will still fail and the device will actually seem to disappear from the system until I reboot. A couple of other things. It is NOT a hardware failure. It is the Windows OS. I know this because I swapped out my DVD drive with a friend with the same model...his machine is fine (he is still running Vista X64) and my machine still fails. For what it is worth. I swapped out my primary disk with the INTEL 160GB SSD. EDIT Here is what System Information shows about my DVD drive Drive D: Description CD-ROM Drive Media Loaded No Media Type DVD Writer Name HL-DT-ST DVDRAM GSA-T50N ATA Device Manufacturer (Standard CD-ROM drives) Status OK Transfer Rate -1.00 kbytes/sec SCSI Target ID 0 PNP Device ID IDE\CDROMHL-DT-ST_DVDRAM_GSA-T50N________________RR04____\5&2B5B7F1D&0&1.0.0 Driver c:\windows\system32\drivers\cdrom.sys (6.1.7600.16385, 144.00 KB (147,456 bytes), 7/13/2009 7:19 PM) Any ideas? HELP! Seth B Spearman

  Read the article

• Wireless 802.11x Disconnects

  - by BillP3rd

  I've looked at (and read) all of the similar questions and none of them get exactly to the issue I'm having at home. I have an 802.11g access point (two, actually, with different SSIDs and on different channels). One is an Airlink AR525W. The other is a Linksys WRT54G v.2. The issue is that at random times, my laptop will lose its wireless connection. This occurs regardless of which access point I'm connected to. When I lose the connection, the affected AP no longer appears in the list of available APs. Also, it doesn't have anything to do with walls or distance. It can happen within 30' and when my laptop is literally within line-of-sight. When it loses the signal, it can take from 10 to 30 minutes to reconnect and it always will without intervention. I've done all the “standard” things to troubleshoot the problem and it has improved. For example, I surveyed other access points in my vicinity and have selected a different channel for each of my APs that no one else nearby is using. Both APs are configured WPA2/AES. I'm down to wondering [Note: This is not a shopping question. I'm not buying a new AP] if the fact that I didn't drop two bills on my APs and instead opted for more modest solutions has anything to do with it? I've oft wondered why anyone would go for the high-end AP when they didn't have to. Also, I am aware of DD-WRT and have chosen not to go there because only one of my APs is supported. Oh, and one final thing. It an HP x64 laptop running Windows 7 Ultimate. The wireless interface is an Atheros AR9285 802.11b/g/n WiFi Adapter. All the latest drivers and service packs have been applied. It did the same thing with my old laptop (a Lenovo) so I don't the problem is in the laptop. It's really annoying when this happens and suggestions of things I haven't thought of or may have overlooked (No, really. As unlikely as it is, I admit that I may have overlooked something :-)) are appreciated.

  Read the article

• Setting up Apache and PHP on Mac OS X Snow Leopard

  - by Martin Bean

  I've recently purchased an Apple iMac. Unfortunately, enabling Apache and PHP has thrown up some problems. I enabled Mac's built-in Web Sharing through System Preferences, at which point I got an output and could add HTML files to my user directory. However, PHP files were being displayed rather than interpreted. I then discovered this is because PHP isn't enabled by default on Mac's Apache set-up. After a quick Google search, I came across this page: http://developer.apple.com/mac/articles/internet/phpeasyway.html I proceeded to the section, Enabling PHP in Apache, copying and pasting the following code snippet into a new Terminal window and hitting Return: set admin_email to (do shell script "defaults read AddressBookMe ExistingEmailAddress") user_www=$HOME/Sites filename=php-test user_index=${user_www}/${filename}.php user_db=${user_www}/${filename}-db.sqlite3 # NOTE: Having a writeable database in your home directory can be a security risk! conf=`apachectl -V | awk -F= '/SERVER_CONFIG/ {print \$2}'| sed 's/"//g'` conf_old=$conf.$$ conf_new=/tmp/php_conf.new touch $user_db chmod a+r $user_index chmod a+w $user_db chmod a+w $user_www echo "Enabling PHP in $conf ..." sed '/#LoadModule php5_module/s/#LoadModule/LoadModule/' $conf | sed "s^[email protected]^<b>\$admin_email</b>^" > $conf_new echo "(Re)Starting Apache ..." osascript <<EOF do shell script "/bin/mv -f $conf $conf_old; /bin/mv $conf_new $conf; /usr/sbin/apachectl restart" with administrator privileges EOF Unfortunately, this has completed thrown Apache and now nothing is being served; instead I'm receiving "Failed to open page" errors because it cannot connect to the server, despite Web Sharing still being active in System Preferences. So therefore I guess my question is this: how can I undo the changes made by the copy-and-pasting of the above code snippet? Admittedly, I don't understand what the above did; I just thought it looked like a Terminal command and tried it. I have no experience in setting up Apache on Mac OS X (and I've only installed XAMPP and WampServer on Windows). So any points on reversing the aforementioned, and then successfully enabling PHP would be great. EDIT: I've discovered, via Console, the following error message is being recorded when trying to browse to 127.0.0.1... (org.apache.httpd) Throttling respawn: Will start in 10 seconds no listening sockets available, shutting down Unable to open logs (org.apache.httpd[13453]) Exited with exit code: 1 Does this point any more to the issue? EDIT #2: I'm now getting this in Console... 15/02/2010 21:24:14 osascript[3597] Error loading /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types: dlopen(/Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types, 262): no suitable image found. Did find: /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types: no matching architecture in universal wrapper

  Read the article

• Are file access times not properly maintained in Mac OS X?

  - by Ether

  I'm trying to determine how file access times are maintained by default in Mac OS X, as I'm trying to diagnose some odd behaviour I'm seeing in a new MBP Unibody (running Snow Leopard, 10.6.2): The symptoms (drilling down to the specific behaviour that seems to be causing the issue): mutt is unable to switch to mailboxes which have recently received new mail mail is delivered by procmail, which updates the mtime of the mbox folder it is updating, but does not alter the atime (this is how new mail detection works: by comparing atime to mtime) however, both the mtime and atime of the mbox file is getting updated Through testing, it does not appear that atimes can be set separately in the filesystem: : [ether@tequila ~]$; touch test : [ether@tequila ~]$; touch -m -t 200801010000 test2 : [ether@tequila ~]$; touch -a -t 200801010000 test3 : [ether@tequila ~]$; ls -l test* -rw------- 1 ether staff 0 Dec 30 11:42 test -rw------- 1 ether staff 0 Jan 1 2008 test2 -rw------- 1 ether staff 0 Dec 30 11:43 test3 : [ether@tequila ~]$; ls -lu test* -rw------- 1 ether staff 0 Dec 30 11:42 test -rw------- 1 ether staff 0 Dec 30 11:43 test2 -rw------- 1 ether staff 0 Dec 30 11:43 test3 The test2 file is created with an old mtime, and the atime is set to now (as it is a new file), which is correct. However, test3 is created with an old atime, but is not set properly on the file. To be sure this is not just behaviour seen with new files, let's modify an old file: : [ether@tequila ~]$; touch -a -t 200801010000 test : [ether@tequila ~]$; ls -l test -rw------- 1 ether staff 0 Dec 30 11:42 test : [ether@tequila ~]$; ls -lu test -rw------- 1 ether staff 0 Dec 30 11:45 test So it would seem that atimes cannot be set explicitly (it is always reset to "now" when either mtime or atime modifications are submitted). Is this something inherent to the filesystem itself, is it something that can be changed, or am I totally crazy and looking in the wrong place? PS. the output of mount is: : [ether@tequila ~]$; mount /dev/disk0s2 on / (hfs, local, journaled) devfs on /dev (devfs, local, nobrowse) map -hosts on /net (autofs, nosuid, automounted, nobrowse) map auto_home on /home (autofs, automounted, nobrowse) ...and Disk Utility says that the drive is of type "Mac OS Extended (Journaled)".

  Read the article

• Email delivery management grievances

  - by joxl

  The question I have may be more of principle than anything else, but here's my dilemma. I manage an email system for a small company (about 20 email users). We own a plain-letter .com domain name through Network Solutions. Our email service is hosted by Google Apps. Recently (Feb. 2011) we've been having customers report that they aren't getting our emails. Upon further investigation it seems that the failed emails are all to a common (well known) domain. We have not received any bounce messages for the emails. We've also contacted a few of the intended recipients, who have reported that the messages are not in their spam box; they simply did not receive anything. In these cases we re-sent the same email to an alternate address on another domain, which was successful received. One customer contacted their email provider about the issue. The provider recommended that we submit a form to be white-listed by their domain. Here's where my problem begins. I feel like this is heading down a slippery slope. Doesn't this undermine the very principle of email? If this is the appropriate action to take in these situations where will it end? In theory (following this model) it could be argued that eventually one will first need to "whitelist" (or more appropriately termed "authenticate") themselves with an email host before actually sending any messages. More to this point, what keeps the "bad" spammers from doing the same thing...? We've just gone full circle. I know avoiding anti-spam measures is a big cat-and-mouse game, but I think this is the wrong way of "patching" the problem. Email standards say that messages should not just disappear silently. I have a problem supporting a model that says "you must do < this to make sure your emails aren't ignored". I have a notion to call the provider and voice my complaint, although I have a feeling it will probably fall on deaf ears. Am I missing something here? Is this an acceptable approach to email spam problems? What should I do?

  Read the article

• keyboard mappings are totally screwed after updating to kde4

  - by zeonglow

  I recently upgraded from KDE 3.5 to KDE 4, and I have been having weird issues with my keyboard. In one of the virtual consoles e.g. when I press ctrl + alt 1 , I can type perfectly, but in KDE, several of the number keys don't work, the left and right arrows don't work either. When I press the right arrow key in xev I get this: KeyRelease event, serial 34, synthetic NO, window 0x3600001, root 0x6f, subw 0x0, time 903459, (111,55), root:(115,836), state 0x10, keycode 114 (keysym 0x1008ff11, XF86AudioLowerVolume), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False When I press the '3' key it toggles my Bookmarks toolbar in Firefox, in xev I get this: KeyPress event, serial 34, synthetic NO, window 0x3600001, root 0x6f, subw 0x0, time 999968, (94,115), root:(98,896), state 0x10, keycode 12 (keysym 0x1008ff30, XF86Favorites), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False KeyRelease event, serial 34, synthetic NO, window 0x3600001, root 0x6f, subw 0x0, time 1000032, (94,115), root:(98,896), state 0x10, keycode 12 (keysym 0x1008ff30, XF86Favorites), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False As this is deeper down, changing the type of keyboard in the KDE meun's has no effect. I'm slowly beginning to wade through the mountains of documentation about the X keyboard model, but there has to be a better way. Does anyone no what it is? Edit: 1234567890 ! after deleting the entire .kde folder. but only until I change the Keyboard settings from the "system settings" applet, then its hosed full time. Regardless of what I set the settings too. (restore to default settings doesn't) 2nd Edit: I'm using Gentoo AMD64, I was upgrading from KDE 3.5 KDE 4.2. I think I had manual settings before, although I didn't change anything. I was originally running KDE without HAL until that stop working a year or so ago. The only customisation I made was to set the multimedia keys to control Amarok. 3rd Edit $ grep xkb /var/log/Xorg.0.log (**) Option "xkb_rules" "evdev" (**) Option "xkb_model" "evdev" (**) Option "xkb_layout" "us" (**) Option "xkb_rules" "evdev" (**) Option "xkb_model" "evdev" (**) Option "xkb_layout" "us" Xorg.0.log has this to say: (WW) AllowEmptyInput is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled. (WW) Disabling Mouse1 (WW) Disabling Keyboard1 My Xorg.conf has this in it. Identifier "Keyboard1" Driver "kbd" Option "AutoRepeat" "500 30" # Specify which keyboard LEDs can be user-controlled (eg, with xset(1)) Option "XkbRules" "xorg" Option "XkbModel" "pc105" Option "XkbLayout" "gb"

  Read the article

• DVD Drive Failing on Windows 7

  - by Seth Spearman

  Hello, I have x64 Windows 7 running on an ASUS M50VM. The DVD drive works completely unreliably if not at all. But the story is not that simple so bear with me...here are the gory details. When I first got the machine it came with Windows XP and I upgraded it to Windows Vista X64 and the DVD worked fine. When Windows 7 RC2 came out I tried it on a Virtual Machine and I liked it so much that I upgraded the machine to Win7 RC1. The DVD worked fine. Of course, RC1 was going to start spontaneously rebooting, so when Windows 7 was released I DID A CLEAN INSTALL of Windows 7. Just to clarify...by clean install I mean I did a FORMAT of the HARD DRIVE and INSTALLED it from scratch. EVER since then the DVD mostly doesn't work. I can sometime read from disk but that will often hang. (Please see my description below of HANG for details.) CD or DVD writes ALWAYS fail with a HANG (I have done a successful write only one time.) Here is what I mean by HANG... *Explorer Window is unresponsive. *Any software accessing the DVD drive is unresponsive. *The DVD tray will not eject. *Using a paper clip will eject but the disk is usually spinning real hard. *Attempting to shut down windows will fail. I have waited as long as ten minutes but the whole OS seems to hang. I do a hard shutdown. *Sometimes accessing the DVD (when it does not cause a HANG) will still fail and the device will actually seem to disappear from the system until I reboot. A couple of other things. It is NOT a hardware failure. It is the Windows OS. I know this because I swapped out my DVD drive with a friend with the same model...his machine is fine (he is still running Vista X64) and my machine still fails. For what it is worth. I swapped out my primary disk with the INTEL 160GB SSD. EDIT Here is what System Information shows about my DVD drive Drive D: Description CD-ROM Drive Media Loaded No Media Type DVD Writer Name HL-DT-ST DVDRAM GSA-T50N ATA Device Manufacturer (Standard CD-ROM drives) Status OK Transfer Rate -1.00 kbytes/sec SCSI Target ID 0 PNP Device ID IDE\CDROMHL-DT-ST_DVDRAM_GSA-T50N________________RR04____\5&2B5B7F1D&0&1.0.0 Driver c:\windows\system32\drivers\cdrom.sys (6.1.7600.16385, 144.00 KB (147,456 bytes), 7/13/2009 7:19 PM) Any ideas? HELP! Seth B Spearman

  Read the article

• Losing internet connectivity on server after installing LogMeIn Hamachi (with server set as gateway node)

  - by Kim Jong-Un

  Our domain controller (SBS 2003) completely lost internet and network connectivity yesterday after I remotely installed LogMeIn Hamachi on it and set it to be a gateway node- in an attempt to create a VPN link between the server and a remote site. I had to go in to the office to resolve the problem as, unsurprisingly, my own remote access to the server was also lost. I was only able to restore network connectivity by deleting a virtual network adapter Hamachi created when making the server the gateway node (called "Hamachi bridge" I believe), then rebooting the server. This is a repeatable problem. Every time I try to get this to work, it just takes the server offline. Why would this bridge affect regular TCP/IP connectivity on the NIC in this way? I have tried a "hub-and-spoke" configuration between the server and our PC at a remote site (server set as hub, remote site as spoke). This caused no such problems with general internet connectivity, and file transfer worked well between the two computers. However, there was a DNS issue with the VPN between the two sites- resulting in Active Directory not being able to communicate between them (could not log on using domain user accounts at remote site if they were not already cached on that machine). I only tried a "gateway" network as LogMeIn support told me: If you can get the Active Directory to work it would only be through a "Gateway" network type with the server acting as the Gateway Node. You would configure the gateway settings on the server in the Hamachi client on that machine to push whatever IP's/DNS settings you prefer and at that point AD would be able (all things being equal) communicate to the client node when it attaches. We do not have any ActiveDirectory configuration info as that's outside the scope of our support. I hope this helps. It would be fantastic if I could get Active Directory to work over a Hamachi VPN connection, without worrying about the server going offline in this way. Does anyone have any ideas how I should proceed, or any theories as to what is going on when I try to use the "gateway" network type? I want to try to narrow down what is going on here.

  Read the article

• Apache and MySQL taking all the memory? Maximum connections?

  - by lpfavreau

  I've a had one of our servers going down (network wise) but keeping its uptime (so looks the server is not losing its power) recently. I've asked my hosting company to investigate and I've been told, after investigation, that Apache and MySQL were at all time using 80% of the memory and peaking at 95% and that I might be needing to add some more RAM to the server. One of their justifications to adding more RAM was that I was using the default max connections setting (125 for MySQL and 150 for Apache) and that for handling those 150 simultaneous connections, I would need at least 3Gb of memory instead of the 1Gb I have at the moment. Now, I understand that tweaking the max connections might be better than me leaving the default setting although I didn't feel it was a concern at the moment, having had servers with the same configuration handle more traffic than the current 1 or 2 visitors before the lunch, telling myself I'd tweak it depending on the visits pattern later. I've also always known Apache was more memory hungry under default settings than its competitor such as nginx and lighttpd. Nonetheless, looking at the stats of my machine, I'm trying to see how my hosting company got those numbers. I'm getting: # free -m total used free shared buffers cached Mem: 1000 944 56 0 148 725 -/+ buffers/cache: 71 929 Swap: 1953 0 1953 Which I guess means that yes, the server is reserving around 95% of its memory at the moment but I also thought it meant that only 71 out of the 1000 total were really used by the applications at the moment looking a the buffers/cache row. Also I don't see any swapping: # vmstat 60 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 0 0 57612 151704 742596 0 0 1 1 3 11 0 0 100 0 0 0 0 57604 151704 742596 0 0 0 1 1 24 0 0 100 0 0 0 0 57604 151704 742596 0 0 0 2 1 18 0 0 100 0 0 0 0 57604 151704 742596 0 0 0 0 1 13 0 0 100 0 And finally, while requesting a page: top - 08:33:19 up 3 days, 13:11, 2 users, load average: 0.06, 0.02, 0.00 Tasks: 81 total, 1 running, 80 sleeping, 0 stopped, 0 zombie Cpu(s): 1.3%us, 0.3%sy, 0.0%ni, 98.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 1024616k total, 976744k used, 47872k free, 151716k buffers Swap: 2000052k total, 0k used, 2000052k free, 742596k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 24914 www-data 20 0 26296 8640 3724 S 2 0.8 0:00.06 apache2 23785 mysql 20 0 125m 18m 5268 S 1 1.9 0:04.54 mysqld 24491 www-data 20 0 25828 7488 3180 S 1 0.7 0:00.02 apache2 1 root 20 0 2844 1688 544 S 0 0.2 0:01.30 init ... So, I'd like to know, experts of serverfault: Do I really need more RAM at the moment? How do they calculate that for 150 simultaneous connections I'd need 3Gb? Thanks for your help!

  Read the article

• HAProxy + Percona XtraDB Cluster

  - by rottmanj

  I am attempting to setup HAproxy in conjunction with Percona XtraDB Cluster on a series of 3 EC2 instances. I have found a few tutorials online dealing with this specific issue, but I am a bit stuck. Both the Percona servers and the HAproxy servers are running ubuntu 12.04. The HAProxy version is 1.4.18, When I start HAProxy I get the following error: Server pxc-back/db01 is DOWN, reason: Socket error, check duration: 2ms. I am not really sure what the issue could be. I have verified the following: EC2 security groups ports are open Poured over my config files looking for issues. I currently do not see any. Ensured that xinetd was installed Ensured that I am using the correct ip address of the mysql server. Any help with this is greatly appreciated. Here are my current config Load Balancer /etc/haproxy/haproxy.cfg global log 127.0.0.1 local0 log 127.0.0.1 local1 notice maxconn 4096 user haproxy group haproxy debug #quiet daemon defaults log global mode http option tcplog option dontlognull retries 3 option redispatch maxconn 2000 contimeout 5000 clitimeout 50000 srvtimeout 50000 frontend pxc-front bind 0.0.0.0:3307 mode tcp default_backend pxc-back frontend stats-front bind 0.0.0.0:22002 mode http default_backend stats-back backend pxc-back mode tcp balance leastconn option httpchk server db01 10.86.154.105:3306 check port 9200 inter 12000 rise 3 fall 3 backend stats-back mode http balance roundrobin stats uri /haproxy/stats MySql Server /etc/xinetd.d/mysqlchk # default: on # description: mysqlchk service mysqlchk { # this is a config for xinetd, place it in /etc/xinetd.d/ disable = no flags = REUSE socket_type = stream port = 9200 wait = no user = nobody server = /usr/bin/clustercheck log_on_failure += USERID #only_from = 0.0.0.0/0 # recommended to put the IPs that need # to connect exclusively (security purposes) per_source = UNLIMITED } MySql Server /etc/services Added the line mysqlchk 9200/tcp # mysqlchk MySql Server /usr/bin/clustercheck # GNU nano 2.2.6 File: /usr/bin/clustercheck #!/bin/bash # # Script to make a proxy (ie HAProxy) capable of monitoring Percona XtraDB Cluster nodes properly # # Author: Olaf van Zandwijk <[email protected]> # Documentation and download: https://github.com/olafz/percona-clustercheck # # Based on the original script from Unai Rodriguez # MYSQL_USERNAME="testuser" MYSQL_PASSWORD="" ERR_FILE="/dev/null" AVAILABLE_WHEN_DONOR=0 # # Perform the query to check the wsrep_local_state # WSREP_STATUS=`mysql --user=${MYSQL_USERNAME} --password=${MYSQL_PASSWORD} -e "SHOW STATUS LIKE 'wsrep_local_state';" 2>${ERR_FILE} | awk '{if (NR!=1){print $2}}' 2>${ERR_FILE}` if [[ "${WSREP_STATUS}" == "4" ]] || [[ "${WSREP_STATUS}" == "2" && ${AVAILABLE_WHEN_DONOR} == 1 ]] then # Percona XtraDB Cluster node local state is 'Synced' => return HTTP 200 /bin/echo -en "HTTP/1.1 200 OK\r\n" /bin/echo -en "Content-Type: text/plain\r\n" /bin/echo -en "\r\n" /bin/echo -en "Percona XtraDB Cluster Node is synced.\r\n" /bin/echo -en "\r\n" else # Percona XtraDB Cluster node local state is not 'Synced' => return HTTP 503 /bin/echo -en "HTTP/1.1 503 Service Unavailable\r\n" /bin/echo -en "Content-Type: text/plain\r\n" /bin/echo -en "\r\n" /bin/echo -en "Percona XtraDB Cluster Node is not synced.\r\n" /bin/echo -en "\r\n" fi

  Read the article

• 403 Forbidden Error when trying to view localhost on Apache

  - by misbehavens

  I think my Apache must be all screwed up. I don't know if it ever worked. I just upgraded to Snow Leopard, and the first step on this tutorial is to start apache and check that it's working by opening http://localhost. It starts fine but when I go to localhost I get a 403 forbidden error. I don't know where to start figuring out how to fix it, so I wonder if a fresh install of Apache would do the trick. What do you think? Update: I found some error logs in /private/var/log/apache2/. Found this in one of the logs. Not sure what it means: [Tue Nov 10 17:53:08 2009] [notice] caught SIGTERM, shutting down [Tue Nov 10 21:49:17 2009] [warn] Init: Session Cache is not configured [hint: SSLSessionCache] Warning: DocumentRoot [/usr/docs/dummy-host.example.com] does not exist Warning: DocumentRoot [/usr/docs/dummy-host2.example.com] does not exist httpd: Could not reliably determine the server's fully qualified domain name, using Andrews-Mac-Pro.local for ServerName mod_bonjour: Skipping user 'andrew' - cannot read index file '/Users/andrew/Sites/index.html'. [Tue Nov 10 21:49:19 2009] [notice] Digest: generating secret for digest authentication ... [Tue Nov 10 21:49:19 2009] [notice] Digest: done [Tue Nov 10 21:49:19 2009] [notice] Apache/2.2.11 (Unix) mod_ssl/2.2.11 OpenSSL/0.9.8k DAV/2 PHP/5.3.0 configured -- resuming normal operations Update: I also found something in the dummy-host.example.com-error_log file. I didn't set these dummy-host things by the way. Is this the default configuration? [Tue Nov 10 21:59:57 2009] [error] [client ::1] client denied by server configuration: /usr/docs Update: Woohoo! I found the file that had the virtual host definitions. It was in /etc/apache2/extra/httpd-vhosts.conf. It had those two dummy virtual host settings in there. I added a localhost virtual host. Not sure if this is necessary, but since it wasn't working before, decided to do it anyway. After removing the old virtual hosts, adding my new localhost virtual host, and restarting apache, it seems to work. So I guess whenever I want to add a virtual host, I only need to add them to this file? Or is there a hosts file somewhere, like there is on Linux? Update: Yes, there is an /etc/hosts file that need to be changed to. Add the virtual host name to that file.

  Read the article

• Sysadmin 101: How can I figure out why my server crashes and monitor performance?

  - by bflora

  I have a Drupal-powered site that seems to have neverending performance problems. It was butt-slow about 5 months ago. I brought in some guys who installed nginx for anonymous visitors, ajaxified a few queries so they wouldn't fire during page load, and helped me find a few bottlenecks in the code. For about a month, the site was significantly faster, though not "fast" by any stretch of the word. Meanwhile, I'm now shelling out $400/month to Slicehost to host a site that gets less than 5,000/uniques a day. Yes, you read that right. Go Drupal. Recently the site started crashing again and is slow again. I can't afford to hire people to come in, study my code from top to bottom, and make changes that may or may not help anymore. And I can't afford to throw more hardware at the problem. So I need to figure out what the problem is myself. Questions: When apache crashes, is it possible to find out what caused it to crash? There has to be a way, right? If so, how can I do this? Is there software I can use that will tell me which process caused my server to die? (e.g. "Apache crashed because someone visited page X." or "Apache crashed because you were importing too many RSS items from feed X.") There's got to be a way to learn this, right? What's a good, noob-friendly way to monitor my current apache performance? My developer friends tell me to "just use Top, dude," but Top shows me a bunch of numbers without any context. I have no clue what qualifies as a bad number or a good number in Top, or which processes are relevant and which aren't. Are there any noob-friendly server monitoring tools out there? Ideally, I could have a page that would give me a color-coded indicator about how apache is performing and then show me a list of processes or pages that are sucking right now. This way, I could know when performance is bad and then what's causing it to be so bad. Why does PHP memory matter? My apparently has a 30MB memory foot print. Will it run faster if I bring that number down? Thanks for any advice. I spent a year or so trying to boost my advertising income so I could hire a contractor to solve my performance woes. I didn't want to have to learn all this sysadmin voodoo. I'm now resigned to the fact that might not have a choice.

  Read the article

• Why is my Linux box dropping network connection? [closed]

  - by Robo

  I have a Debian server in the form of a Raspberry Pi running Raspian. It has a USB Wi-Fi connection. Sometimes it would not respond when I SSH to it, and would require a reboot. I found something in syslog that may indicate what the problem is, can someone help with what this means? Dec 16 15:34:17 raspberrypi wpa_supplicant[1501]: wlan0: WPA: Group rekeying completed with 00:21:29:6c:5c:3d [GTK=CCMP] Dec 16 16:17:01 raspberrypi /USR/SBIN/CRON[2109]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Dec 16 16:34:17 raspberrypi wpa_supplicant[1501]: wlan0: WPA: Group rekeying completed with 00:21:29:6c:5c:3d [GTK=CCMP] Dec 16 17:17:01 raspberrypi /USR/SBIN/CRON[2127]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Dec 16 17:34:17 raspberrypi wpa_supplicant[1501]: wlan0: WPA: Group rekeying completed with 00:21:29:6c:5c:3d [GTK=CCMP] Dec 16 18:17:01 raspberrypi /USR/SBIN/CRON[2142]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Dec 16 18:34:17 raspberrypi wpa_supplicant[1501]: wlan0: WPA: Group rekeying completed with 00:21:29:6c:5c:3d [GTK=CCMP] Dec 16 19:17:01 raspberrypi /USR/SBIN/CRON[2161]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Dec 16 19:31:29 raspberrypi kernel: [16615.391509] ieee80211 phy0: wlan0: No probe response from AP 00:21:29:6c:5c:3d after 500ms, disconnecting. Dec 16 19:31:29 raspberrypi wpa_supplicant[1501]: wlan0: CTRL-EVENT-DISCONNECTED bssid=00:21:29:6c:5c:3d reason=4 Dec 16 19:31:29 raspberrypi kernel: [16615.416189] cfg80211: Calling CRDA to update world regulatory domain Dec 16 19:31:30 raspberrypi ifplugd(wlan0)[1444]: Link beat lost. Dec 16 19:31:40 raspberrypi ifplugd(wlan0)[1444]: Executing '/etc/ifplugd/ifplugd.action wlan0 down'. Dec 16 19:31:40 raspberrypi wpa_supplicant[1501]: wlan0: CTRL-EVENT-TERMINATING - signal 15 received Dec 16 19:31:40 raspberrypi ifplugd(wlan0)[1444]: Program executed successfully. Dec 16 19:31:42 raspberrypi ntpd[1928]: Deleting interface #2 wlan0, 192.168.1.10#123, interface stats: received=321, sent=327, dropped=0, active_time=16596 secs Dec 16 19:31:42 raspberrypi ntpd[1928]: 202.6.116.123 interface 192.168.1.10 -> (none) Dec 16 19:31:42 raspberrypi ntpd[1928]: 203.99.128.34 interface 192.168.1.10 -> (none) Dec 16 19:31:42 raspberrypi ntpd[1928]: 203.118.148.40 interface 192.168.1.10 -> (none) Dec 16 19:31:42 raspberrypi ntpd[1928]: 202.89.49.65 interface 192.168.1.10 -> (none) Dec 16 19:31:42 raspberrypi ntpd[1928]: peers refreshed

  Read the article

< Previous Page | 635 636 637 638 639 640 641 642 643 644 645 646  | Next Page >