Search Results

Search found 25182 results on 1008 pages for 'ask'.

Page 66/1008 | < Previous Page | 62 63 64 65 66 67 68 69 70 71 72 73  | Next Page >

• No more internet connection after update in 14.04 with Intel Dual Band Wireless AC 7260

  - by luis

  My Dell XPS 15 (haswell) was working fine until I stupidly accepted recently to apply Ubuntu updates. Since then, my wifi does not work (it shows "device not managed" when clicking wifi icon in toolbar). Even USB to Ethernet adapter does not seem to work. Bluetooth at least "sees" other bluetooth devices around... See below output from dmesg (dmesg |grep iwl) : [ 886.462459] iwlwifi 0000:06:00.0: irq 51 for MSI/MSI-X [ 886.462561] iwlwifi 0000:06:00.0: Direct firmware load failed with error -2 [ 886.462562] iwlwifi 0000:06:00.0: Falling back to user helper [ 886.463284] iwlwifi 0000:06:00.0: loaded firmware version 22.1.7.0 op_mode iwlmvm [ 886.475345] iwlwifi 0000:06:00.0: Detected Intel(R) Dual Band Wireless AC 7260, REV=0x144 [ 886.475433] iwlwifi 0000:06:00.0: L1 Enabled; Disabling L0S [ 886.475684] iwlwifi 0000:06:00.0: L1 Enabled; Disabling L0S [ 886.689214] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs' Below the output from modinfo iwlwifi: filename: /lib/modules/3.13.0-29- generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko license: GPL author: Copyright(c) 2003-2013 Intel Corporation <[email protected]> version: in-tree: description: Intel(R) Wireless WiFi driver for Linux firmware: iwlwifi-100-5.ucode firmware: iwlwifi-1000-5.ucode firmware: iwlwifi-135-6.ucode firmware: iwlwifi-105-6.ucode firmware: iwlwifi-2030-6.ucode firmware: iwlwifi-2000-6.ucode firmware: iwlwifi-5150-2.ucode firmware: iwlwifi-5000-5.ucode firmware: iwlwifi-6000g2b-6.ucode firmware: iwlwifi-6000g2a-5.ucode firmware: iwlwifi-6050-5.ucode firmware: iwlwifi-6000-4.ucode firmware: iwlwifi-3160-7.ucode firmware: iwlwifi-7260-7.ucode srcversion: 1E6912E109D5A43B310FB34 alias: pci:v00008086d0000095Asv*sd00005490bc*sc*i* (a pack of lines of kind "alias: pci:xxxxx...." that I guess are not helpful) alias: pci:v00008086d0000095Bsv*sd00005290bc*sc*i* depends: cfg80211 intree: Y vermagic: 3.13.0-29-generic SMP mod_unload modversions signer: Magrathea: Glacier signing key sig_key: 66:02:CB:36:F1:31:3B:EA:01:C4:BD:A9:65:67:CF:A7:23:C9:70:D8 sig_hashalgo: sha512 parm: swcrypto:using crypto in software (default 0 [hardware]) (int) parm: 11n_disable:disable 11n functionality, bitmap: 1: full, 2: disable agg TX, 4: disable agg RX, 8 enable agg TX (uint) parm: amsdu_size_8K:enable 8K amsdu size (default 0) (int) parm: fw_restart:restart firmware in case of error (default true) (bool) parm: antenna_coupling:specify antenna coupling in dB (defualt: 0 dB) (int) parm: wd_disable:Disable stuck queue watchdog timer 0=system default, 1=disable, 2=enable (default: 0) (int) parm: nvm_file:NVM file name (charp) parm: bt_coex_active:enable wifi/bt co-exist (default: enable) (bool) parm: led_mode:0=system default, 1=On(RF On)/Off(RF Off), 2=blinking, 3=Off (default: 0) (int) parm: power_save:enable WiFi power management (default: disable) (bool) parm: power_level:default power save level (range from 1 - 5, default: 1) (int) I downloaded the latest versions of iwlwifi firmware from git (git clone git://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git; copy iwlwifi-3160-9.ucode iwlwifi-7260-9.ucode iwlwifi-7265-9.ucode to /lib/firmware and reboot) but as you can imagine it did not help. Update #1: Downloaded from http://wireless.kernel.org/en/users/Drivers/iwlwifi?action=AttachFile&do=get&target=iwlwifi-7260-ucode-22.15.8.0.tgz and copied the file into /lib/firmware. After reloading it with modprobe, it seems to be OK: [ 14.761283] iwlwifi 0000:06:00.0: enabling device (0000 -> 0002) [ 14.761472] iwlwifi 0000:06:00.0: irq 51 for MSI/MSI-X [ 14.772478] iwlwifi 0000:06:00.0: loaded firmware version 22.15.8.0 op_mode iwlmvm [ 14.800274] iwlwifi 0000:06:00.0: Detected Intel(R) Dual Band Wireless AC 7260, REV=0x144 [ 14.800349] iwlwifi 0000:06:00.0: L1 Enabled; Disabling L0S [ 14.800657] iwlwifi 0000:06:00.0: L1 Enabled; Disabling L0S [ 15.007048] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs' However, clicking in wifi in the toolbar still shows "device not managed". Any clues? Many thanks! Luis

  Read the article

• How to boot with Intel GMA500 Poulsbo graphics

  - by Seyed Mohammad

  I have a Sony VAIO netbook with Intel GMA-500 Poulsbo Graphics and I'm trying to boot the latest Ubuntu-12.04 Beta-2 using a bootable USB. According to this Ubuntu-Wiki, support for Intel GMA-500 Poulsbo graphics is promising in Precise-Beta2 and should work out of the box. Of course the wiki talks about a problem when booting from USB and states that restarting X using: sudo service lightdm restart will bring a functional graphical desktop, but nothing happens for me! Any help is highly appreciated.

  Read the article

• Dual boot windows 8 and Ubuntu with Windows 8 Boot manager

  - by Mevin Babu

  I have two partitions on my hard-didk , I have installed ubuntu on my 1st partition and windows 8 later on another partition.Now i can only boot into windows 8 because it doesn't recognize Ubuntu. How would i dual boot my PC without using grub . I would like using Windows 8 boot manager as its pretty neat. I tried using easyBCD but it doesn't work.It causes the boot manager to switch to windows 7 Boot Manager .Is there anyother work around or solution Any help would be appreciated. Note: The windows 8 boot Manager is sky blue color interactive menu with mouse and other options and windows 7 boot manager is the normal black and white one where you can only use your keyboard

  Read the article

• How can I keep a folder synchronized to an external USB hard drive in Ubuntu?

  - by Cesar

  I have a growing music collection which I manually keep in sync with an external USB drive. Sometimes I edit their ID3 tags, add or delete a file in either the hard drive or the USB drive, and I would like to keep those changes synchronized between both. Does Ubuntu has something available that would help me with this scenario? Preferably something easy to use with a UI. Update: To clarify my question, changes may happen on both the local hard drive or the USB drive, so the sync process must be on both directions.

  Read the article

• Allow Incoming Responses from Curl On Ubuntu 11.10 - Curl

  - by Daniel Adarve

  I'm trying to get a Curl Response from an outside server, however I noticed I cant neither PING the server in question nor connect to it. I tried disabling the iptables firewall but I had no success. My server is running behind a Cisco Linksys WRTN310N Router with the DD-wrt firmware Installed. In which I already disabled the firewall. Here are my network settings: Ifconfig eth0 Link encap:Ethernet HWaddr 00:26:b9:76:73:6b inet addr:192.168.1.120 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::226:b9ff:fe76:736b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:49713 errors:0 dropped:0 overruns:0 frame:0 TX packets:30987 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:52829022 (52.8 MB) TX bytes:5438223 (5.4 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:341 errors:0 dropped:0 overruns:0 frame:0 TX packets:341 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:27604 (27.6 KB) TX bytes:27604 (27.6 KB) /etc/resolv.conf nameserver 192.168.1.1 /etc/nsswitch.com passwd: compat group: compat shadow: compat hosts: files dns networks: files protocols: db files services: db files ethers: db files rpc: db files netgroup: nis /etc/host.conf order hosts,bind multi on /etc/hosts 127.0.0.1 localhost 127.0.0.1 callcenter # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 192.168.1.120 netmask 255.255.255.0 network 192.168.1.1 broadcast 192.168.1.255 gateway 192.168.1.1 The Url to which im trying to get a connection to is https://www.veripayment.com/integration/index.php When I ping it on terminal heres what I get daniel@callcenter:~$ ping www.veripayment.com PING www.veripayment.com (69.172.200.5) 56(84) bytes of data. --- www.veripayment.com ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms Thanks in Advance

  Read the article

• How to use rhythmbox-client on LAN?

  - by Kaustubh P

  A few days ago I had asked this question, and according to one suggestion, used rhythmote. It is a web-interface to change songs on a rhythmbox playing on some PC. However, its not what I had thought of, and I stumbled upon documentation for rhythmbox-client. I tried a few ways of using it, but was unsuccessful. Let me show you a few ways of how I did it. The rhythmbox is running at address 192.168.1.4, lets call it jukebox. Passing the address as a parameter Hoping that I would be able to see and browse through songs on the jukebox rhythmbox-client 192.168.1.4 But, I get this message (rhythmbox-client:8370): Rhythmbox-WARNING **: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken. (rhythmbox-client:8370): Rhythmbox-WARNING **: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken. SSH ssh -l jukebox 192.168.1.4 rhythmbox-client --print-playing Which spat this at me: (rhythmbox-client:9389): Rhythmbox-WARNING **: /bin/dbus-launch terminated abnormally with the following error: Autolaunch error: X11 initialization failed. rhythmbox-client as root gksudo rhythmbox-client 192.168.1.4 A rhythmbox client comes up, but with no music shown in the library. I am guessing this is running on my own computer. Can anyon tell me how rhythmbox-client is to be run, and is it even correct of me to think that I can get a rhythmbox window showing the songs on the jukebox? PS: There were a few other solutions mentioned, but I want to evaluate each and every one of them. Thanks.

  Read the article

• Kernel, dpkg, sudo and apt-get corrupted

  - by TECH4JESUS

  Here are some errors that I am getting: 1) A proper configuration for Firestarter was not found. If you are running Firestarter from the directory you built it in, run make install-data-local to install a configuration, or simply make install to install the whole program. Firestarter will now close. root@p:/# firestarter ** (firestarter:5890): WARNING **: The connection is closed (firestarter:5890): GnomeUI-WARNING **: While connecting to session manager: None of the authentication protocols specified are supported. (firestarter:5890): GConf-WARNING **: Client failed to connect to the D-BUS daemon: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken. (firestarter:5890): GConf-WARNING **: Client failed to connect to the D-BUS daemon: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken. (firestarter:5890): GConf-WARNING **: Client failed to connect to the D-BUS daemon: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken. (firestarter:5890): GConf-WARNING **: Client failed to connect to the D-BUS daemon: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken. (firestarter:5890): GConf-WARNING **: Client failed to connect to the D-BUS daemon: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken. (firestarter:5890): GConf-WARNING **: Client failed to connect to the D-BUS daemon: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken. (firestarter:5890): GConf-WARNING **: Client failed to connect to the D-BUS daemon: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken. ^C 2) Also I cannot apt-get install sudo root@p:/# apt-get install sudo Reading package lists... Done Building dependency tree Reading state information... Done sudo is already the newest version. The following packages were automatically installed and are no longer required: gir1.2-rb-3.0 gir1.2-gstreamer-0.10 libntfs10 python-mako libdmapsharing-3.0-2 rhythmbox-data libx264-116 rhythmbox libiso9660-7 librhythmbox-core5 libvpx0 libmatroska4 gir1.2-gst-plugins-base-0.10 rhythmbox-mozilla rhythmbox-plugin-zeitgeist libattica0 libgpac0.4.5 python-markupsafe libmusicbrainz4c2a rhythmbox-plugin-cdrecorder rhythmbox-plugins libaudiofile0 Use 'apt-get autoremove' to remove them. 0 upgraded, 0 newly installed, 0 to remove and 18 not upgraded. 9 not fully installed or removed. Need to get 0 B/76.3 MB of archives. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? Y /bin/sh: 1: /usr/sbin/dpkg-preconfigure: not found (Reading database ... 495741 files and directories currently installed.) Preparing to replace linux-image-3.2.0-24-generic 3.2.0-24.39 (using .../linux-image-3.2.0-24-generic_3.2.0-24.39_amd64.deb) ... dpkg (subprocess): unable to execute old pre-removal script (/var/lib/dpkg/info/linux-image-3.2.0-24-generic.prerm): No such file or directory dpkg: warning: subprocess old pre-removal script returned error exit status 2 dpkg - trying script from the new package instead ... dpkg (subprocess): unable to execute new pre-removal script (/var/lib/dpkg/tmp.ci/prerm): No such file or directory dpkg: error processing /var/cache/apt/archives/linux-image-3.2.0-24-generic_3.2.0-24.39_amd64.deb (--unpack): subprocess new pre-removal script returned error exit status 2 dpkg (subprocess): unable to execute installed post-installation script (/var/lib/dpkg/info/linux-image-3.2.0-24-generic.postinst): No such file or directory dpkg: error while cleaning up: subprocess installed post-installation script returned error exit status 2 Preparing to replace linux-image-3.2.0-25-generic 3.2.0-25.40 (using .../linux-image-3.2.0-25-generic_3.2.0-25.40_amd64.deb) ... dpkg (subprocess): unable to execute old pre-removal script (/var/lib/dpkg/info/linux-image-3.2.0-25-generic.prerm): No such file or directory dpkg: warning: subprocess old pre-removal script returned error exit status 2 dpkg - trying script from the new package instead ... dpkg (subprocess): unable to execute new pre-removal script (/var/lib/dpkg/tmp.ci/prerm): No such file or directory dpkg: error processing /var/cache/apt/archives/linux-image-3.2.0-25-generic_3.2.0-25.40_amd64.deb (--unpack): subprocess new pre-removal script returned error exit status 2 dpkg (subprocess): unable to execute installed post-installation script (/var/lib/dpkg/info/linux-image-3.2.0-25-generic.postinst): No such file or directory dpkg: error while cleaning up: subprocess installed post-installation script returned error exit status 2 Errors were encountered while processing: /var/cache/apt/archives/linux-image-3.2.0-24-generic_3.2.0-24.39_amd64.deb /var/cache/apt/archives/linux-image-3.2.0-25-generic_3.2.0-25.40_amd64.deb E: Sub-process /usr/bin/dpkg returned an error code (1)

  Read the article

• RAID5 over LVM on Ubuntu Server 12.04.3

  - by April Ethereal

  I'm trying to create a RAID5 software array using LVM. I use VirtualBox as I'm only learning how LVM works. So I've created 4 virtual SCSI drives and then did the following: pvcreate /dev/sd[b-e] vgcreate /dev/sd[b-e] raid5_vg lvcreate --type raid5 -i 3 -L 1G -n raid_lv raid5_vg However, I get an error after the last command: WARNING: Unrecognised segment type raid5 Using default stripesize 64.00 KiB Rounding size (256 extents) up to stripe boundary size (258 extents) Cannot update volume group raid5_vg with unknown segments in it! So it looks like raid5 is not a valid segment type. "lvm segtypes" also doesn't contain 'raid5' entry: root@ubuntu-lvm:~# lvm segtypes striped zero error free snapshot mirror So my question is - how could I create RAID5 logical volume using LVM only? It seems that it is possible, I saw a few references (not for Ubuntu, unfortunately) for RedHat and Gentoo systems. I don't want to use mdadm for now, until I find out that it is mandatory. Some info about my system is below: root@ubuntu-lvm:~# uname -a Linux ubuntu-lvm 3.8.0I use Ubuntu Server 12.04.3 (i686)-29-generic #42~precise1-Ubuntu SMP Wed Aug 14 15:31:16 UTC 2013 i686 i686 i386 GNU/Linux root@ubuntu-lvm:~# dpkg -l | grep lvm ii lvm2 2.02.66-4ubuntu7.3 The Linux Logical Volume Manager Thanks.

  Read the article

• Get more information about the crash

  - by Tito

  when i issue the command last in my terminal i see the following entries i.e. "crash" How can i find out more information about the crash: Is there any system dump file generated or a backtrace file that i can see or analyze. reboot system boot 3.2.0-32-generic Mon Nov 12 23:58 - 09:13 (09:14) tito pts/1 192.168.26.5 Mon Nov 12 23:56 - crash (00:01) tito pts/4 192.168.26.5 Mon Nov 12 22:46 - crash (01:12)

  Read the article

• rsnapshot intervals in configuration file…

  - by Patrick

  A simple question about rsnapshot. In order to perform daily backups I'm going to add lines to cron in my Ubuntu. Then, why do I have also these lines in the rsnapshot.conf ? ######################################### # BACKUP INTERVALS # # Must be unique and in ascending order # # i.e. hourly, daily, weekly, etc. # ######################################### interval hourly 6 interval daily 7 interval weekly 4 #interval monthly 3 If I use cron, should I disable them ? thanks ps. I've just realized that in the crontab I still have "hourly" and "daily". Should I then uncomment only the one I use in the crontab ? And what's the point to specify hourly if it is already specified in cron ? I'm a bit confused. # crontab -e 0 */4 * * * /usr/local/bin/rsnapshot hourly 30 23 * * * /usr/local/bin/rsnapshot daily

  Read the article

• Can't adjust screen brightness on Macbook Pro 10,1 Ubuntu 13.10

  - by ben101

  I recently installed Ubuntu on my retina Macbook Pro (following this great guide: http://cberner.com/2013/03/01/installing-ubuntu-13-04-on-macbook-pro-retina/) Everything works fine so far however the screen brightness / backlight cannot be adjusted neither by using the assigned key nor by any other means. I know, I'm not the first to address this problem, but all the suggested solutions I found so far did not work for me. I unsuccessfully tried the following: Including Option "RegistryDwords" "EnableBrightnessControl=1" in the Devices-Section of /etc/X11/xorg.conf the application xbacklight I also haven't found any file such as mbp_backlight or apple_backlight on my system which probably would be a starting point I'm using the Nvidia-driver. (BTW: With the nouveau-driver, the keys to adjust the brightness work. However, with the nouveau driver Ubuntu does not resume from suspend mode) Any suggestions what I can do? Thanks!

  Read the article

• Minidlna Directory Issues

  - by Somnambulist

  I've done my searching and can't find an answer to THIS specific issue. I have my minidlna set up and running - but it's not really done properly. First off, when I open the server on my bluray player, all of my movies are listed twice - when they are certainly not saved on my external twice. Second, when I open the server - rather than reading "Movies" "TV" "Music", etc - It just mashes all of my movies, tv, and some other folders all together with no real organization. I never had this problem when I had my Windows set up, so I know it's something configured improperly more-so than my external drive giving me gruff. Here's my minidlna.conf file: # This is the configuration file for the MiniDLNA daemon, a DLNA/UPnP-AV media # server. # # Unless otherwise noted, the commented out options show their default value. # # On Debian, you can also refer to the minidlna.conf(5) man page for # documentation about this file. media_dir=/media/somnambulist/Ghost In You # This option can be specified more than once if you want multiple directories # scanned. # # If you want to restrict a media_dir to a specific content type, you can # prepend the directory name with a letter representing the type (A, P or V), # followed by a comma, as so: # * "A" for audio (eg. media_dir=A,/var/lib/minidlna/music) # * "P" for pictures (eg. media_dir=P,/var/lib/minidlna/pictures) # * "V" for video (eg. media_dir=V,/var/lib/minidlna/videos) # # WARNING: After changing this option, you need to rebuild the database. Either # run minidlna with the '-R' option, or delete the 'files.db' file # from the db_dir directory (see below). # On Debian, you can run, as root, 'service minidlna force-reload' instead. #media_dir=/var/lib/minidlna media_dir=V,/media/somnambulist/Ghost In You/Movies media_dir=V,/media/somnambulist/Ghost In You/TV media_dir=P,/home/somnambulist/Pictures # Path to the directory that should hold the database and album art cache. db_dir=/home/somnambulist/serverart # Path to the directory that should hold the log file. log_dir=/home/somnambulist/serverlog # Minimum level of importance of messages to be logged. # Must be one of "off", "fatal", "error", "warn", "info" or "debug". # "off" turns of logging entirely, "fatal" is the highest level of importance # and "debug" the lowest. #log_level=warn # Use a different container as the root of the directory tree presented to # clients. The possible values are: # * "." - standard container # * "B" - "Browse Directory" # * "M" - "Music" # * "P" - "Pictures" # * "V" - "Video" # if you specify "B" and client device is audio-only then "Music/Folders" will be used as root root_container=B # Network interface(s) to bind to (e.g. eth0), comma delimited. #network_interface= # IPv4 address to listen on (e.g. 192.0.2.1). #listening_ip= # Port number for HTTP traffic (descriptions, SOAP, media transfer). port=8200 # URL presented to clients. # The default is the IP address of the server on port 80. #presentation_url=http://example.com:80 # Name that the DLNA server presents to clients. friendly_name=Somnambulist Media Server # Serial number the server reports to clients. serial=12345678 # Model name the server reports to clients. #model_name=Windows Media Connect compatible (MiniDLNA) # Model number the server reports to clients. model_number=1 # Automatic discovery of new files in the media_dir directory. #inotify=yes # List of file names to look for when searching for album art. Names should be # delimited with a forward slash ("/"). album_art_names=Cover.jpg/cover.jpg/AlbumArtSmall.jpg/albumartsmall.jpg/AlbumArt.jpg/albumart.jpg/Album.jpg/album.jpg/Folder.jpg/folder.jpg/Thumb.jpg/thumb.jpg # Strictly adhere to DLNA standards. # This allows server-side downscaling of very large JPEG images, which may # decrease JPEG serving performance on (at least) Sony DLNA products. #strict_dlna=no # Support for streaming .jpg and .mp3 files to a TiVo supporting HMO. #enable_tivo=no # Notify interval, in seconds. #notify_interval=895 # Path to the MiniSSDPd socket, for MiniSSDPd support. #minissdpdsocket=/run/minissdpd.sock` And here's the error I get in terminal when I run: sudo service minidlna restart sudo service minidlna force-reload Force restart error: Restarting DLNA/UPnP-AV media server minidlna [2013/08/12 21:19:27] minidlna.c:474: error: Media directory "/media/somnambulist/Ghost In You/Movies" not accessible! [Permission denied] [2013/08/12 21:19:27] minidlna.c:474: error: Media directory "/media/somnambulist/Ghost In You/TV" not accessible! [Permission denied] Force-reload error: Restarting DLNA/UPnP-AV media server minidlna [2013/08/12 21:19:46] minidlna.c:474: error: Media directory "/media/somnambulist/Ghost In You/Movies" not accessible! [Permission denied] [2013/08/12 21:19:46] minidlna.c:474: error: Media directory "/media/somnambulist/Ghost In You/TV" not accessible! [Permission denied] rm: cannot remove ‘/home/somnambulist/serverart/files.db’: Permission denied rm: cannot remove ‘/home/somnambulist/serverart/art_cache/media/somnambulist/Ghost In You/Movies/Slumdog Millionaire/Slumdog.Millionaire.Cover.jpg’: Permission denied rm: cannot remove ‘/home/somnambulist/serverart/art_cache/media/somnambulist/Ghost In You/Movies/Zack and Miri Make a Porno/ZackAndMiriMakeAPornoCover.jpg’: Permission denied [2013/08/12 21:19:46] minidlna.c:744: warn: Failed to clean old file cache. [ OK ] I've spent hours on this at this point, read through various files - and even had a friend who is relatively Ubuntu-savvy try to help me via chat - no such luck. Thanks in advance for any help.

  Read the article

• Bluetooth not working on an Alienware m14x r2

  - by S. L.

  on my alienware m14x r2 laptop with ubuntu 12.04.1 x64, the bluetooth interface is not working. WLAN works fine. I have a dualboot install with ubuntu & win 7 on this laptop. In win 7, the bluetooth interface works fine, because its all activated in BIOS. I have the killer wireless-n 1202 a/g/n interface with integrated bluetooth 4.0 in this laptop. Here is some code : sudo rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 064e:8128 Suyin Corp. Bus 002 Device 003: ID 0cf3:3004 Atheros Communications, Inc. Bus 002 Device 004: ID 187c:0521 Alienware Corporation dmesg | grep "Bluetooth" [ 2.590377] Bluetooth: Core ver 2.16 [ 2.590395] Bluetooth: HCI device and connection manager initialized [ 2.590397] Bluetooth: HCI socket layer initialized [ 2.590399] Bluetooth: L2CAP socket layer initialized [ 2.590403] Bluetooth: SCO socket layer initialized [ 2.591518] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 2.591519] Bluetooth: BNEP filters: protocol multicast [ 2.599411] Bluetooth: RFCOMM TTY layer initialized [ 2.599415] Bluetooth: RFCOMM socket layer initialized [ 2.599416] Bluetooth: RFCOMM ver 1.11 [ 2.696552] Bluetooth: Generic Bluetooth USB driver ver 0.6 [ 2.696751] Bluetooth: Atheros AR30xx firmware driver ver 1.0 [ 2.702607] Bluetooth: Configuration file not found ar3k/ramps_0x11020000_40.dfu [ 2.702609] Bluetooth: Loading sysconfig file failed Any ideas to fix that problem ?

  Read the article

• can't mount ntfs partition without root access

  - by tachyons

  whenever try to mount ntfs partition it says Error mounting: mount exited with exit code 1: helper failed with: Unprivileged user can not mount NTFS block devices using the external FUSE library. Either mount the volume as root, or rebuild NTFS-3G with integrated FUSE support and make it setuid root. Please see more information at http://tuxera.com/community/ntfs-3g-faq/#unprivileged I tried this answer but it wont work

  Read the article

• XEROX Phaser 3160N installation on UBUNTU 12.04 LTE machine

  - by Greg Verrall

  I have recently had windows XP die on one of my machines, and have installed Linux UBUNTU. The OS works great, except for installing the Xerox Phaser 3160N printer. The OS can find and install the network printer, but when I print a test page, it tells me “Internal Error – Please use the correct driver”. I have the correct drivers, as your support team have sent me the link, (http://www.support.xerox.com/support/phaser-3160/file-download/enau.html?operatingSystem=linux&fileLanguage=en_GB&contentId=105724&from=downloads&viewArchived=false) but I cannot install these drivers to run the printer. These are the instructions from the online guide for installing on a Linux machine: 1. Make sure that the machine is connected to your network and powered on. Also, your machine’s IP address should have been set. 2. Insert the supplied software CD into your CD-ROM drive. 3. Double-click CD-ROM icon that appears on your Linux desktop. 4. Double-click the Linux folder. 5. Double-click the install.sh icon. 6. The Xerox Installer window opens. Click Continue. 7. The Add printer wizard window opens. Click Next. 8. Select Network printer and click Search button. 9. The Printer’s IP address and model name appears on list field. 10. Select your machine and click Next. I get as far as step 5, and step 6 never happens, if it did, it would be very easy from there. There are options to add additional software to UBUNTU, however it does not recognise the installation CD as valid when I try to add it as a source. Any ideas on who can help me? regards, Greg Verrall

  Read the article

• Which LAN card / module combinations proven to work with Wake on LAN

  - by pablomo

  I've got a 12.04 headless server that I've been trying to get to work with wake-on-lan. The card is Marvel 88E8053 using the sky2 module. Although WOL is enabled in BIOS and ethtool shows the card as WOL enabled, it refuses to wake when I send the magic packet. I have verified that the packet is being received OK when the machine is on. The machine does wake OK from a BIOS alarm which suggests it is a network card issue. I've seen reference to bugs in sky2 that mean WOL fails in recent versions of Ubuntu (and have tried a module conf file as suggested here but to no avail) So I am thinking the best bet is to replace the ethernet card with one that definitely works with WOL in 12.04 - please could you post your card make and model no if you are using it successfully?

  Read the article

• ERRNO 5 Input/Output Error

  - by CCarey

  Going up for my first ubuntu installation and encountered a critical error. Mind that I am installing on my Macbook Pro, and have already removed all other partitions. (I'm installing with a CD) My Ubuntu version is: "ubuntu-12.10-desktop-i386" So once the installation gets to something around "Finishing copying files", a great big "[ERRNO5] Input/Output Error" pops up on the screen. Obviously this halts and crashes the whole installation. Now, I've already run a disk check, memtest, and cpu load test, and all came up green. I have also redownloaded ubuntu twice, md5 match both times, and burnt four disks. None got past this error. If anyone could help me out, that would be greatly appreciated! Cheers!

  Read the article

• No Wi-Fi after system reboot

  - by ILya

  Something strange is happening... I've installed a Wi-Fi card into my Ubuntu Server 11.04 machine. To configure it I do the following: sudo vi /etc/network/interfaces add: iface wlan0 inet dhcp wpa-driver wext wpa-ssid "Sweet Home" wpa-ap-scan 1 wpa-proto WPA wpa-pairwise TKIP wpa-group TKIP wpa-key-mgmt WPA-PSK wpa-psk <A KEY> auto wlan0 then: $ sudo /etc/init.d/networking restart * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... ssh stop/waiting ssh start/running, process 1522 ssh stop/waiting ssh start/running, process 1590 And my machine successfully gets an ip to my wireless adapter. But after reboot it doesn't get any ip in wireless network. To fix it I run /etc/init.d/networking restart again and all is fine again - it gets an ip. I understand that I simply should add it to my startup scripts to make it work properly, but maybe there is a better way to configure it?

  Read the article

• How to setup Dual Head with "radeon" driver for R770?

  - by user1709408

  I want to make dual head setup without xrandr but with Xinerama. I put "Screen 1" line into xorg.conf, but card still show identical output on DVI-2 and DVI-3 It is important to use xinerama for me (to glue three monitors), that's why i decide not to use ranrd (randr is incompatible with xinerama as i read somewhere) Here is my videocard (HD 4850 X2): lspci | grep R700 03:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI R700 [Radeon HD 4850] 04:00.0 Display controller: Advanced Micro Devices [AMD] nee ATI R700 [Radeon HD 4850] Here is how monitors are connected: grep "DVI" /var/log/Xorg.0.log [ 1210.002] (II) RADEON(0): Output DVI-0 using monitor section Monitor0 [ 1210.048] (II) RADEON(0): Output DVI-1 has no monitor section [ 1210.079] (II) RADEON(0): EDID for output DVI-0 [ 1210.080] (II) RADEON(0): Printing probed modes for output DVI-0 [ 1210.128] (II) RADEON(0): EDID for output DVI-1 [ 1210.128] (II) RADEON(0): Output DVI-0 connected [ 1210.128] (II) RADEON(0): Output DVI-1 disconnected [ 1210.128] (II) RADEON(0): Output DVI-0 using initial mode 1920x1200 [ 1210.160] (II) RADEON(1): Output DVI-2 using monitor section Monitor2 [ 1210.215] (II) RADEON(1): Output DVI-3 has no monitor section [ 1210.246] (II) RADEON(1): EDID for output DVI-2 [ 1210.247] (II) RADEON(1): Printing probed modes for output DVI-2 [ 1210.299] (II) RADEON(1): EDID for output DVI-3 [ 1210.300] (II) RADEON(1): Printing probed modes for output DVI-3 [ 1210.300] (II) RADEON(1): Output DVI-2 connected [ 1210.300] (II) RADEON(1): Output DVI-3 connected [ 1210.300] (II) RADEON(1): Output DVI-2 using initial mode 1920x1200 [ 1210.300] (II) RADEON(1): Output DVI-3 using initial mode 1920x1200 Here is my /etc/X11/xorg.conf Section "ServerFlags" Option "RandR" "0" Option "Xinerama" "1" EndSection Section "ServerLayout" Identifier "Three Head Layout" Screen "MyPrecious0" Screen "MyPrecious2" RightOf "MyPrecious0" Screen "MyPrecious3" LeftOf "MyPrecious0" EndSection Section "Screen" Identifier "MyPrecious0" Monitor "Monitor0" Device "Device300" EndSection Section "Screen" Identifier "MyPrecious2" Monitor "Monitor2" Device "Device400" EndSection Section "Screen" Identifier "MyPrecious3" Monitor "Monitor3" Device "Device401" EndSection Section "Device" Identifier "Device300" BusID "PCI:3:0:0" Screen 0 Driver "radeon" EndSection Section "Device" Identifier "Device400" BusID "PCI:4:0:0" Screen 0 Driver "radeon" EndSection Section "Device" Identifier "Device401" BusID "PCI:4:0:0" Screen 1 Driver "radeon" EndSection Section "Monitor" Identifier "Monitor0" EndSection Section "Monitor" Identifier "Monitor2" EndSection Section "Monitor" Identifier "Monitor3" EndSection I tried to switch to vesa driver (didn't work for me) I tried to add options like Option "ZaphodHeads" "DVI-2" and Option "ZaphodHeads" "DVI-3" into sections "Device 400" and "Device 401" (this didn't help because "ZaphodHeads" option is for ranrd, and randr is disabled by decision) I tried to merge sections "Device 400" and "Device 401" into one section and add Option "ZaphodHeads" "DVI-2,DVI-3" (see comment about randr above) single section setup helps to change log line RADEON(1): Output DVI-3 has no monitor section into RADEON(1): Output DVI-3 using monitor section Monitor3 but nothing was enough to switch from screen cloning to separate screens. This problem (lack of documentation on radeon driver) is similar to these: Radeon display driver clones monitors while using Xinerama (moderators decision to close that problem was wrong) Ubuntu 12.10 multi-monitor setup isn't working The problem is solvable, because this hardware worked as three headed for me earlier with gentoo/xorg-server-1.3 Xorg -configure creates setup for the first monitor on the first GPU Please don't advise to use fglrx/aticonfig/amdcccle (this goes against my religion beliefs)

  Read the article

• xubuntu 12.04 totally refuses to boot after install with wubi on old computer. any tips or suggestions on things i can do to fix this problem?

  - by WizardinBlack

  so, i downloaded xubuntu 12.04 32-bit (not alt version) from the xubuntu.org website and placed the .zip into a folder named XUBUNTU on my desktop. i then extracted the files to that folder and ran wubi. i selected xubuntu from the drop down and clicked install. i let it do its thing and then chose the option to reboot when prompted. this is when i went to my girlfriends house for the day and left my laptop (dell latitude 120L) to finish the install. i came back home (about 8 hours later) to find my computer on the windows 7 log in screen when i rebooted my computer once more. i booted xubuntu just fine and things seemed to work perfectly. i turned off the pc and went to bed. next morning i booted xubuntu again without problems. i rebooted and went to windows, then next time i tried booting xubuntu in the middle of the splash screen it went black and the cpu light stopped blinking. i force shut down the computer and tried booting again when the same thing happened (instead of going black the splash just froze). i went back to windows and uninstalled and reintalled the os and havent beej able to boot it since. i even tried booting lubuntu with the same problem. please help!

  Read the article

• Bad Screen Flicker from video recording of recordmydesktop

  - by Tarun

  I have ubuntu 11.10 and I installed recordmydesktop. Video recording from recordmydesktop always result in screen flicker. In recording I see half of the screen moving forward while half would be stuck. I checked the settings and "Frame per Second" is set to 15 One such recording is available here - http://www.youtube.com/watch?v=QafF44m2Ttk&feature=youtu.be I am quite new to Ubuntu and not sure what is wrong.

  Read the article

• Wireless cuts out on Toshiba Satellite S7208

  - by alecRN

  I recently got a Toshiba Satellite L875-S7208 with Windows 7 preinstalled. I installed Ubuntu 12.04 LTS dual boot to the same Windows partition. However, usually 15 minutes or less after booting, the wifi connection dies. Here's some hopefully relevant information: lspci -knn 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09) Subsystem: Toshiba America Info Systems Device [1179:fb40] Kernel driver in use: i915 Kernel modules: i915 00:14.0 USB controller [0c03]: Intel Corporation Panther Point USB xHCI Host Controller [8086:1e31] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: xhci_hcd 00:16.0 Communication controller [0780]: Intel Corporation Panther Point MEI Controller #1 [8086:1e3a] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller [0c03]: Intel Corporation Panther Point USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: ehci_hcd 00:1b.0 Audio device [0403]: Intel Corporation Panther Point High Definition Audio Controller [8086:1e20] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb40] Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 1 [8086:1e10] (rev c4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 2 [8086:1e12] (rev c4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 3 [8086:1e14] (rev c4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller [0c03]: Intel Corporation Panther Point USB Enhanced Host Controller #1 [8086:1e26] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge [0601]: Intel Corporation Panther Point LPC Controller [8086:1e59] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel modules: iTCO_wdt 00:1f.2 SATA controller [0106]: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] [8086:1e03] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: ahci 00:1f.3 SMBus [0c05]: Intel Corporation Panther Point SMBus Controller [8086:1e22] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel modules: i2c-i801 02:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) Subsystem: Realtek Semiconductor Co., Ltd. Device [10ec:8211] Kernel driver in use: rtl8192ce Kernel modules: rtl8192ce 03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) Subsystem: Toshiba America Info Systems Device [1179:fb37] Kernel driver in use: r8169 Kernel modules: r8169 lsmod Module Size Used by snd_hda_codec_hdmi 32474 1 snd_hda_codec_realtek 224066 1 joydev 17693 0 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep parport_pc 32866 0 ppdev 17113 0 arc4 12529 2 snd_hda_intel 33773 3 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq psmouse 87692 0 serio_raw 13211 0 rtl8192ce 84826 0 rtl8192c_common 75767 1 rtl8192ce rtlwifi 111202 1 rtl8192ce mac80211 506816 3 rtl8192ce,rtl8192c_common,rtlwifi snd 78855 16 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device sparse_keymap 13890 0 uvcvideo 72627 0 videodev 98259 1 uvcvideo v4l2_compat_ioctl32 17128 1 videodev mac_hid 13253 0 mei 41616 0 wmi 19256 0 soundcore 15091 1 snd i915 472941 3 snd_page_alloc 18529 2 snd_hda_intel,snd_pcm drm_kms_helper 46978 1 i915 cfg80211 205544 2 rtlwifi,mac80211 drm 242038 4 i915,drm_kms_helper i2c_algo_bit 13423 1 i915 video 19596 1 i915 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62099 0 ums_realtek 18248 0 uas 18180 0 usb_storage 49198 1 ums_realtek dmesg | grep firmware [ 15.692951] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 16.240881] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 452.419288] rtl8192c_common:rtl92c_firmware_selfreset(): 8051 reset fail. [ 458.572211] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 465.440640] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 472.337617] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 479.175471] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 485.978582] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 492.764893] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 499.579348] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 506.386934] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 513.209545] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 519.991365] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 526.778375] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 533.629695] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 540.426004] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 547.238125] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 554.024434] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 560.854794] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 567.678160] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 574.494666] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 581.336653] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 588.157710] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 595.221122] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 602.047429] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 608.829534] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 615.639079] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 622.454991] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 629.273231] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 636.056613] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 642.858096] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 649.640753] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 657.184094] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 664.008018] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 670.838639] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 677.675418] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 684.507255] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 691.310994] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 698.095325] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 704.914509] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 711.725178] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin uname -r 3.2.0-29-generic ifconfig eth0 Link encap:Ethernet HWaddr 4c:72:b9:59:6c:61 inet addr:192.168.0.11 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::4e72:b9ff:fe59:6c61/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4447 errors:0 dropped:0 overruns:0 frame:0 TX packets:2762 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3671147 (3.6 MB) TX bytes:335133 (335.1 KB) Interrupt:42 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:515 errors:0 dropped:0 overruns:0 frame:0 TX packets:515 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:83153 (83.1 KB) TX bytes:83153 (83.1 KB) wlan0 Link encap:Ethernet HWaddr 74:e5:43:32:47:95 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:280 errors:0 dropped:0 overruns:0 frame:0 TX packets:51 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:32958 (32.9 KB) TX bytes:10431 (10.4 KB)

  Read the article

• LightDM will not start after stopping it

  - by Sweeters

  I am running Ubuntu 11.10 "Oneiric Ocelot", and in trying to install the nvidia CUDA developer drivers I switched to a virtual terminal (Ctrl-Alt-F5) and stopped lightdm (installation required that no X server instance be running) through sudo service lightdm stop. Re-starting lightdm with sudo service lightdm start did not work: A couple of * Starting [...] lines where displayed, but the process hanged. (I do not remember at which point, but I think it was * Starting System V runlevel compatibility. I manually rebooted my laptop, and ever since booting seems to hang, usually around the * Starting anac(h)ronistic cron [OK] log line (not consistently at that point, though). From that point on, I seem to be able to interact with my system only through a tty session (Ctrl-Alt-F1). I've tried purging and reinstalling both lightdm and gdm, as well as selecting both as the default display managers (through sudo dpkg-reconfigure [lightdm / gdm] or by manually editing /etc/X11/default-display-manager) through both apt-get and aptitude (that shouldn't make a difference anyway) after updating the packages, but the problem persists. Some of the responses I'm getting are the following: After running sudo dpkg-reconfigure lightdm (but not ... gdm) I get the following message: dpkg-maintscript-helper:warning: environment variable DPKG_MATINSCRIPT_NAME missing dpkg-maintscript-helper:warning: environment variable DPKG_MATINSCRIPT_PACKAGE missing After trying sudo service lightdm start or sudo start lightdm I get to see the boot loading screen again but nothing changes. If I go back to the tty shell I see lightdm start/running, process <num> but ps -e | grep lightdm gives no output. After trying sudo service gdm start or sudo starg gdm I get the gdm start/running, process <num> message, and gdm-binary is supposedly an active process, but all that happens is that the screen blinks a couple of times and nothing else. Other candidate solutions that I'd found on the web included running startx but when I try that I get an error output [...] Fatal server error: no screens found [...]. Moreover, I made sure that lightdm-gtk-greeter is installed but that did not help either. Please excuse my not including complete outputs/logs; I am writing this post from another computer and it's hard to manually copy the complete logs. Also, I've seen several posts that had to do with similar problems, but either there was no fix, or the one suggested did not work for me. In closing: Please help! I very much hope to avoid re-installing Ubuntu from scratch! :) Alex @mosi I did not manage to fix the NVIDIA kernel driver as per your instructions. I should perhaps mention that I'm on a Dell XPS15 laptop with an NVIDIA Optimus graphics card, and that I have bumblebee installed (which installs nvidia drivers during its installation, I believe). Issuing the mentioned commands I get the following: ~$uname -r 3.0.0-12-generic ~$lsmod | grep -i nvidia nvidia 11713772 0 ~$dmesg | grep -i nvidia [ 8.980041] nvidia: module license 'NVIDIA' taints kernel. [ 9.354860] nvidia 0000:01:00.0: power state changed by ACPI to D0 [ 9.354864] nvidia 0000:01:00.0: power state changed by ACPI to D0 [ 9.354868] nvidia 0000:01:00.0: enabling device (0006 -> 0007) [ 9.354873] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9.354879] nvidia 0000:01:00.0: setting latency timer to 64 [ 9.355052] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 280.13 Wed Jul 27 16:53:56 PDT 2011 Also, running aptitude search nvidia gives me the following: p nvidia-173 - NVIDIA binary Xorg driver, kernel module a p nvidia-173-dev - NVIDIA binary Xorg driver development file p nvidia-173-updates - NVIDIA binary Xorg driver, kernel module a p nvidia-173-updates-dev - NVIDIA binary Xorg driver development file p nvidia-96 - NVIDIA binary Xorg driver, kernel module a p nvidia-96-dev - NVIDIA binary Xorg driver development file p nvidia-96-updates - NVIDIA binary Xorg driver, kernel module a p nvidia-96-updates-dev - NVIDIA binary Xorg driver development file p nvidia-cg-toolkit - Cg Toolkit - GPU Shader Authoring Language p nvidia-common - Find obsolete NVIDIA drivers i nvidia-current - NVIDIA binary Xorg driver, kernel module a p nvidia-current-dev - NVIDIA binary Xorg driver development file c nvidia-current-updates - NVIDIA binary Xorg driver, kernel module a p nvidia-current-updates-dev - NVIDIA binary Xorg driver development file i nvidia-settings - Tool of configuring the NVIDIA graphics dr p nvidia-settings-updates - Tool of configuring the NVIDIA graphics dr v nvidia-va-driver - v nvidia-va-driver - I've tried manually installing (sudo aptitude install <package>) packages nvidia-common and nvidia-settings-updates but to no avail. For example, sudo aptitude install nvidia-settings-updates returns the following log: Reading package lists... Building dependency tree... Reading state information... Reading extended state information... Initializing package states... Writing extended state information... No packages will be installed, upgraded, or removed. 0 packages upgraded, 0 newly installed, 0 to remove and 83 not upgraded. Need to get 0 B of archives. After unpacking 0 B will be used. Writing extended state information... Reading package lists... Building dependency tree... Reading state information... Reading extended state information... Initializing package states... Writing extended state information... The same happens with the Linux headers (i.e. I cannot seem to be able to install linux-headers-3.0.0-12-generic). The output of aptitude search linux-headers is as follows: v linux-headers - v linux-headers - v linux-headers-2.6 - i linux-headers-2.6.38-11 - Header files related to Linux kernel versi i linux-headers-2.6.38-11-generic - Linux kernel headers for version 2.6.38 on i A linux-headers-2.6.38-8 - Header files related to Linux kernel versi i A linux-headers-2.6.38-8-generic - Linux kernel headers for version 2.6.38 on v linux-headers-3 - v linux-headers-3.0 - v linux-headers-3.0 - i A linux-headers-3.0.0-12 - Header files related to Linux kernel versi p linux-headers-3.0.0-12-generic - Linux kernel headers for version 3.0.0 on p linux-headers-3.0.0-12-generic- - Linux kernel headers for version 3.0.0 on p linux-headers-3.0.0-12-server - Linux kernel headers for version 3.0.0 on p linux-headers-3.0.0-12-virtual - Linux kernel headers for version 3.0.0 on p linux-headers-generic - Generic Linux kernel headers p linux-headers-generic-pae - Generic Linux kernel headers v linux-headers-lbm - v linux-headers-lbm - v linux-headers-lbm-2.6 - v linux-headers-lbm-2.6 - p linux-headers-lbm-3.0.0-12-gene - Header files related to linux-backports-mo p linux-headers-lbm-3.0.0-12-gene - Header files related to linux-backports-mo p linux-headers-lbm-3.0.0-12-serv - Header files related to linux-backports-mo p linux-headers-server - Linux kernel headers on Server Equipment. p linux-headers-virtual - Linux kernel headers for virtual machines @heartsmagic I did try purging and reinstalling any nvidia driver packages, but it did not seem to make a difference, My xorg.conf file contains the following: # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 280.13 ([email protected]) Wed Jul 27 17:15:58 PDT 2011 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Unknown" HorizSync 28.0 - 33.0 VertRefresh 43.0 - 72.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection

  Read the article

• Mac OS X roaming profile from Samba with OpenLDAP backend on Ubuntu 11.10

  - by Sam Hammamy

  I have been battling for a week now to get my Mac (Mountain Lion) to authenticate on my home network's OpenLDAP and Samba. From several sources, like the Ubuntu community docs, and other blogs, and after a hell of a lot of trial and error and piecing things together, I have created a samba.ldif that will pass the smbldap-populate when combined with apple.ldif and I have a fully functional OpenLDAP server and a Samba PDC that uses LDAP to authenticate the OS X Machine. The problem is that when I login, the home directory is not created or pulled from the server. I get the following in system.log Sep 21 06:09:15 Sams-MacBook-Pro.local SecurityAgent[265]: User info context values set for sam Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Got user: sam Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Got ruser: (null) Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Got service: authorization Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in od_principal_for_user(): no authauth availale for user. Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in od_principal_for_user(): failed: 7 Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Failed to determine Kerberos principal name. Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Done cleanup3 Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Kerberos 5 refuses you Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): pam_sm_authenticate: ntlm Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_acct_mgmt(): OpenDirectory - Membership cache TTL set to 1800. Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in od_record_check_pwpolicy(): retval: 0 Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): Establishing credentials Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): Got user: sam Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): Context initialised Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): pam_sm_setcred: ntlm user sam doesn't have auth authority All that's great and good and I authenticate. Then I get CFPreferences: user home directory for user kCFPreferencesCurrentUser at /Network/Servers/172.17.148.186/home/sam is unavailable. User domains will be volatile. Failed looking up user domain root; url='file://localhost/Network/Servers/172.17.148.186/home/sam/' path=/Network/Servers/172.17.148.186/home/sam/ err=-43 uid=9000 euid=9000 If you're wondering where /Network/Servers/IP/home/sam comes from, it's from a couple of blogs that said the OpenLDAP attribute apple-user-homeDirectory should have that value and the NFSHomeDirectory on the mac should point to apple-user-homeDirectory I also set the attr apple-user-homeurl to <home_dir><url>smb://172.17.148.186/sam/</url><path></path></home_dir> which I found on this forum. Any help is appreciated, because I'm banging my head against the wall at this point. By the way, I intend to create a blog on my vps just for this, and create an install script in python that people can download so no one has to go through what I've had to go through this week :) After some sleep I am going to try to login from a windows machine and report back here. Thanks Sam

  Read the article

• Intel I217LM ethernet controller not detected by Ubuntu 12.04LTS

  - by Alexandr Kurilin

  My last installation of Ubuntu 12.04 on a machine using an ASUS Q87M-E motherboard with an Intel I217LM Ethernet controller has failed to detect the ethernet card. The only thing displayed by ifconfig -a is the loopback. I double-checked in the BIOS, and the controller should be online. $ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no $ lspci 00:00.0 Host bridge: Intel Corporation Haswell DRAM Controller (rev 06) 00:01.0 PCI bridge: Intel Corporation Haswell PCI Express x16 Controller (rev 06) 00:02.0 VGA compatible controller: Intel Corporation Haswell Integrated Graphics Controller (rev 06) 00:03.0 Audio device: Intel Corporation Haswell HD Audio Controller (rev 06) 00:14.0 USB controller: Intel Corporation Lynx Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Lynx Point MEI Controller #1 (rev 04) 00:16.3 Serial controller: Intel Corporation Lynx Point KT Controller (rev 04) 00:19.0 Ethernet controller: Intel Corporation Device 153a (rev 04) 00:1a.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Lynx Point HD Audio Controller (rev 04) 00:1d.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Lynx Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Lynx Point 6-Port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation Lynx Point SMBus Controller (rev 04) $ lsmod Module Size Used by vesafb 13844 1 snd_hda_codec_realtek 224173 1 arc4 12529 2 joydev 17693 0 usbhid 47238 0 hid 99636 1 usbhid rfcomm 47604 0 rt73usb 31735 0 crc_itu_t 12707 1 rt73usb rt2x00usb 20808 1 rt73usb rt2x00lib 55326 2 rt73usb,rt2x00usb mac80211 506862 2 rt2x00usb,rt2x00lib cfg80211 205774 2 rt2x00lib,mac80211 eeepc_wmi 13109 0 bnep 18281 2 asus_wmi 24456 1 eeepc_wmi sparse_keymap 13890 1 asus_wmi psmouse 97485 0 bluetooth 180153 10 rfcomm,bnep ppdev 17113 0 snd_hda_intel 33719 6 snd_hda_codec 127706 2 snd_hda_codec_realtek,snd_hda_intel snd_seq_midi 13324 0 snd_hwdep 17764 1 snd_hda_codec snd_rawmidi 30748 1 snd_seq_midi serio_raw 13211 0 snd_pcm 97275 2 snd_hda_intel,snd_hda_codec snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61929 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq parport_pc 32866 1 snd 79041 21 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_rawmidi,snd_pcm,snd_seq,snd_timer,snd_seq_device video 19651 0 soundcore 15091 1 snd wmi 19256 1 asus_wmi snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mac_hid 13253 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp $ ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1091 errors:0 dropped:0 overruns:0 frame:0 TX packets:1091 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:80048 (80.0 KB) TX bytes:80048 (80.0 KB) wlan0 Link encap:Ethernet HWaddr 00:fd:07:91:a8:b9 inet addr:172.16.42.4 Bcast:172.16.42.255 Mask:255.255.255.0 inet6 addr: fe80::2fd:7ff:fe91:a8b9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:56644 errors:0 dropped:0 overruns:0 frame:0 TX packets:36417 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:85270918 (85.2 MB) TX bytes:3413849 (3.4 MB) additionally, running sudo lshw -C network returns: *-network UNCLAIMED description: Ethernet Controller [...] I'm pretty stumped at this point. This doesn't sound like a very uncommon ethernet controller and I figured it would be picked up by the system. Does anybody have advice for how to deal with this? Anything specific I should look into to figure out what could be causing this? Edit: It seems that following the guide on the Intel e1000e drivers page allowed the card to start working. Is this a real fix or is there a better way?

  Read the article

< Previous Page | 62 63 64 65 66 67 68 69 70 71 72 73  | Next Page >