Search Results

Search found 3084 results on 124 pages for 'lan'.

Page 66/124 | < Previous Page | 62 63 64 65 66 67 68 69 70 71 72 73  | Next Page >

• WEP key not working on laptop running Ubuntu

  - by stupid-idiot

  I can't connect to my router via wifi from my laptop (running Ubuntu) even if I'm 100% sure the WEP key I punch in is correct. It works via LAN though. I'm also not able to ping localhost 127.0.0.1. I had some problems setting up the radio on my network card but I think that that works since it finds some wireless networks. (Although it's much much faster than Windows it's useless since I can't download any libraries for development.) What could be wrong with my setup?

  Read the article

• Routing only some local IPs through VPN on dd-wrt

  - by bo-inge-ostberg

  Much similar to this entry: http://serverfault.com/questions/94283/using-dd-wrt-to-connect-to-vpn-and-forward-all-traffic-of-certain-devices-through , I have set up my router with dd-wrt + OpenVPN to connect to a VPN. This works fine, and all traffic from behind the router goes through the VPN. How do I route(?) traffic in the router so that only certain IPs from the LAN will go through the VPN, while the others take the "normal" route? Is it also possible to allow traffic from certain local IPs to go ONLY through the VPN, making it impossible for them to use the regular internet connection if the VPN is down? I know this question was answered in the post I linked to, but that just doesn't seem to work for me. The routing table and rules change, but traffic still just goes through the VPN.

  Read the article

• Cyrus: authentication failure: checkpass failed

  - by Nick

  I'm trying to get Cyrus IMAP (v 2.2 on Ubuntu 9.04) setup and working, but I'm having a bit of trouble getting the login working correctly. I've created a mailbox for my test user "nrahl": cm user/nrahl and then created a password: $ saslpasswd2 nrahl I'm attempting to connect to the mailbox using Thunderbird. I'm using the machine's LAN IP address as the host, and "nrahl" as the username. It connects to the server and prompts me for the password. When I enter it, I get "Login to server failed." in Thunderbird, and /var/log/mail.log shows: Apr 15 19:20:01 IMAP cyrus/imap[1930]: accepted connection Apr 15 19:20:09 IMAP cyrus/imap[1930]: badlogin: [192.168.5.21] plaintext nrahl SASL(-13): authentication failure: checkpass failed Part of /etc/imapd.conf with comments removed: sieveusehomedir: false sievedir: /var/spool/sieve #mailnotifier: zephyr #sievenotifier: zephyr #dracinterval: 0 #drachost: localhost hashimapspool: true allowplaintext: yes sasl_mech_list: PLAIN #allowapop: no #sasl_maximum_layer: 256 #loginrealms: example.com #virtdomains: userid #defaultdomain: sasl_pwcheck_method: saslauthd #sasl_auxprop_plugin: sasldb sasl_auto_transition: no

  Read the article

• Access forbidden! using xampp on macosx 10.5

  - by erikvold

  I installed xampp back around January 2009, and CF8 to test coldfusion on my macbook (note: I do not think that this issue is related to CF, but only xampp). I only ever used the apache part of xampp, and this was working for over a year. In the last couple of months at the most I've started getting the following error message (even for none CF sites, and non .cfm pages, the error occurs for .html files..): Access forbidden! You don't have permission to access the requested object. It is either read-protected or not readable by the server. If you think this is a server error, please contact the webmaster Error 403 erikvold.lan Sun Mar 21 20:58:45 2010 Apache/2.2.11 (Unix) DAV/2 mod_ssl/2.2.11 OpenSSL/0.9.7l PHP/5.2.9 mod_perl/2.0.4 Perl/v5.10.0 As far as I recall I haven't made any change, so it's like it was working for a year then just stopped working..

  Read the article

• How should I remotely manage Dell Poweredge 2850 running Ubuntu server?

  - by Saul

  First I've got to say I'm a Linux / Ubuntu novice, so go gentle on me as I'm on day 3. I've managed to get Ubuntu server Ubuntu 8.04 LTS installed and running on the Poweredge 1850 I bought off ebay. The box will go in a rack at my office but I want to be able to work on it and power on and off from home and I gather that (maybe) IPMI over LAN might be the way to do this, or maybe its something to do with BMC or something? I want to be able to administer/manage from a client PC at home running XP. I will be configuring the office router to port forward port 80 and 443 to the Ubuntu server running Apache2, and I'm puzzled about how the remote management works (unless it comes on a different port forwarded to a different internal IP) Thanks for any help

  Read the article

• How to make other computers connected to my workgroup able to browse my web server via my private local domain www.mydomain.local?

  - by Motivated Student

  Background I have a broadband connection. The fiber optic cable running from outside to my building is connected to a converter unit. The output of the converter is connected to a router. The router also provides 8 LAN ports to which the computers are connected. Shortly speaking, all computers are interconnected in a workgroup as opposed to a domain. My computer hosts an IIS web server using a private or local domain name www.mydomain.local. I has added 127.0.0.1 www.mydomain.local to the hosts file in the server C:\Windows\System32\drivers\etc so I can browse the site from within the server. So far so good. How to make other computers connected to my workgroup able to browse my web server via my private local domain www.mydomain.local? Note: Again, I am a newbie. I have no idea what I should do next.

  Read the article

• Accessing a website's directory in IIS from File Zilla

  - by Cdeez

  I have my Asp.net website deployed in my IIS's Virtual directory. Usually a FTP software like File Zilla is used to upload files to a website's directory from a remote system. File Zilla asks for a Host name, Username, password to connect to the remote server. Now all I want is my users in LAN should be able to access this directory from their system using FTP software like FileZilla. So how can I provide the Host name, username and password to my website's directory. I tried to find it on google but no help. Detailed steps please. Its IIS 5.1 version.

  Read the article

• Windows Server - Dual NIC Bandwidth Pooling

  - by tsilb

  I have a Windows Server 2008 machine with dual NICs. Both are plugged into the same switch in a typical one-switch, one-gateway home network. This server is used almost exclusively for inbound connections. It hosts a web server (IIS 6), SQL server, and file server (via LAN UNC paths and mapped drives). How do I make best use of inbound bandwidth across both NICs? For example, if I connect to it by hostname and one of the interfaces has high traffic, I'd like the new connection to use the other interface.

  Read the article

• Down for everyone or just me?

  - by Click Ok

  When I try access a website, and it is down, I head to http://www.downforeveryoneorjustme.com, and test it. But lately, my home network PCs cannot access facebook.com, and I tried the that service and the answer was: It's just you. http://facebook.com is up. Ok, that got me. I tried several browsers and 3 PCs in my LAN and it don't works. I don't know how to troubleshoot this. What some step-by-step to troubleshoot that problem? Output from ping command: Disparando facebook.com [69.171.234.21] com 32 bytes de dados: Resposta de 69.171.234.21: bytes=32 tempo=256ms TTL=245 Resposta de 69.171.234.21: bytes=32 tempo=255ms TTL=246 Resposta de 69.171.234.21: bytes=32 tempo=251ms TTL=245 Resposta de 69.171.234.21: bytes=32 tempo=255ms TTL=246 PS.: I thank you for the nice help, but then I suppose that the first step of a step-by-step to troubleshoot is ping from command line?

  Read the article

• Yet another "can't connect to MySQL over the network" question - but i seriously tried everything

  - by mireille raad

  Hello, I was left with the easy task of installing moodle. I am VPNing to 2 servers, one for the database and the other apache/php server 1 must connect over LAN to the mySQL db on server 2 I added a user with following priveleges : +---------------+------------+ | host | user | +---------------+------------+ | % | mir | | 10.10.40.15 | mir | | x.x.x.x | mir | | localhost | mir | Disabled firewall temporary made sure that my username/password combinations are correct, flushed priveleges, restarted mysqld i wnt to /etc/my.cnf .. if i try to add the port=3306 bind-address=10.10.40.15 or anything that is different from 0.0.0.0 or 127.0.0.1 - mysql wouldn't restart i read and tried many forums and pages and asked friends for tips but nothing works So my question to you : are there any networking extensions that need to be installed for mysql, how do i know nothing is missing from the installation any troubleshooting tips, any idea how to fix this, any step by step check list, am i missing something simple/stupid, please anything that comes to mind, let me know Appreciate your feedback on this friday night stuck at work :P

  Read the article

• Acer Aspire 3680 Wireless Signal Problem

  - by SHiNKiROU

  I am using Acer Aspire 3680. I recently reinstalled Windows Vista, and the wireless did not work by default. I installed the "Atheros Wireless LAN Driver" on this site: http://support.acer-euro.com/drivers/notebook/as_3680.html The result, the wireless APs are successfully scanned. However, when I tried to join a network, even with 5/5 signal, an error message showed up diagnosing signal too little. I restarted as Ubuntu, and wireless worked perfectly, with same computer position. Even more confusing, When I moved to the kitchen (2 meters close to the router), the wireless connected, when I move back to my room, wireless failed on Vista and worked on Ubuntu. It is clearly the driver problem. Acer laptops seems come with pre-installed drivers, but after re-installation, they are all gone. (I can't find the original Acer backup disc) Please do not answer "move closer to the AP" and something related to "interference", as wireless worked with Ubuntu's default driver.

  Read the article

• Mac OS X: pushing all traffic through a VMWare VM [closed]

  - by bj99

  I want to set up an Astaro (Sophos) UTM in a Virtual Machine. The Setup should be at the end the following: Cable Modem (one IP adress) | [Ethernet] Sophos UTM (running as VM [VMWare Fusion 5] on the MacMini) | [WIFI] Airport Express v2 (for sharing Local Network to wireless and wired clients) 1)| [WIFI] 2)| [Ethernet over Thunderbolt Ethernet Adapter]* Clients MacMini (Local File Server) *To have the Mini also protected behind the UTM So the setup process for the UTM works fine, but then the problems start: I just have one external IP (from my cable modem provider)== So if I put the VM in briged mode my Internet connection drops, because the MacMini also has its IP adress. If I put the VM to NAT mode the Mini itself is not protected by the UTM So: is there a way to hide the en0 interface(Ethernet) and the en1 interface (Wifi) from the MacMini, so that they not even appear in System Preferences Network section but are available to the VM? That way the Mini must connect to the en2 interface (Thunderbolt adapter) to make any Internet/LAN connection and I just use the given single IP from the Cable Modem. Thaks for any suggestions... Sebastian

  Read the article

• Not able to connect to perforce server outside of localhost

  - by bobber205

  My setup is a Qwest PK5000 router with a Linksys router running Tomato. I have DMZ pointed towards my router. (The server is on the tomato router). I tried my applications that open up sockets and Utorrent (port 6883) and I ended having to do advanced port forwarding and forward specific ports in addition to having DMZ on my router. The problem is that I cannot connect to perforce when on another machine on the LAN or off. Any ideas? :) Thanks!

  Read the article

• How low-power can a home server get?

  - by Halik

  I've got quite simple question actually. How green, low-power and efficient x86 home server can I build using consumer parts with rather constrained budget. After looking through some Google hits I've found out that system based on dual-core atom, some modest mITX board (gigabit lan, integrated audio and gfx etc), one RAM module and one 'green' WD HDD, powered by picoITX PSU uses about 30W at idle up to 40 at load. Can you get lower (or how much lower) then that? Maybe some VIA nano chips, or single core atom? My home server would take care of some back-upping mixed with little ftp/http traffic.

  Read the article

• Implications of allowing Windows clients to use NTLMv1?

  - by Boden

  I have a web application that I'd like to authenticate to using pass-through NTLM for SSO. There is a problem, however, in that NTLMv2 apparently will not work in this scenario (without the application storing an identical password hash). I enabled NTLMv1 on one client machine (Vista) using its local group policy: Computer-Windows Settings-Security Settings-Network Security: LAN Manager authentication level. I changed it to Send LM & NTLM - use NTLMv2 session security if negotiated. This worked, and I'm able to login to the web application using NTLM. Now this application would be used by all of my client machines... so I'm wondering what the security risks are if I was push this policy out to all of them (not to the domain controller itself though)?

  Read the article

• website not accessible with IIS6 while NAT is configured in Windows 2003

  - by Mohammed Rizwan

  I have Windows2003 server configured with IIS 6. Until now it was working fine, but since I enabled NAT for my users to access the internet via this server, the website becomes unavailable. Note that I have two nics on the server one is WAN and 2nd is for LAN. Both IPs are behind the firewall. If I stop the NAT then the website is available externally. I tried to search the answer in this forum but didn't find appropriate one or maybe didn't properly understand. I'll appreciate if anyone can help me sorting out this issue.

  Read the article

• How do you confirm network adapter is gigabit capable?

  - by StrandedPirate

  Upgrading my network to gigabit speeds and don't know how to determine if the NIC in one of the systems is capable of gigabit speed. The documentation from the manufacturer states this: Network adapter 10/100/1000 Ethernet LAN on system board However when I go to the properties of the NIC under Speed & Duplex my only options are: 10 Mb Full 10 Mb Half 100 Mb Full 100 Mb Half Auto Is there a command line I can run that will give me more detail about the NIC? Windows 7 x64 OS New Info: The new switch I just bought has a light to indicate 1000Mbps. I can tell from the light that this NIC is indeed negotiating at 1000Mbps but I'd still like to know how to determine this from the console in windows.

  Read the article

• mini linux for browsing media playing

  - by Martin Beckett

  I'm looking for a small linux install (<100Mb) that can just run a browser and ideally a media player. It's to fit in a spare recovery partition on my laptop and be a quick boot for non-work stuff when I'm on the road. I have used Puppy-linux and DSL before but they have lots of stuff I don't need. Is there something like these that just concentrates on running a browser in the way xbmc does for videos? ps. The size requirement was to fit in the existing 100Mb win7 recovery partition, but that can be resized. The main idea was something that booted very quickly without the 10min wait while windows does all the corporate stuff and realizes it isn't on the LAN - and could be shutdown instantly.

  Read the article

• Windows Server 2008 R2 DNS Server Intermittently Unresponsive

  - by Ablue

  Throughout the day out DNS servers (2x Win 2k8 R2 servers) are unable to respond to requests. The requests that fail are all on the .root zone that are either cached or obtained from 1 of 5 DNS servers we forward to before going to root hints. At first I thought the DNS servers we were forwarding to were flaky. So I added some more in. Currently the forwarding list looks like ISP DNS 1 OPEN DNS 1 ISP DNS 2 OPEN DNS 2 ISP DNS 3 I have tried: Turning off root hints. Set record scavenging to 7 days. Using dnscmd /config /EnableEDNSProbes 0 as per this. Packet capture at the DNS server shows that there is a lot of query responses with server failure between lan clients and the local dns server; it does not appear to be forwarding those requests. So maybe a problem with caching? Anyhow, does anything have anything I can try to get this working?

  Read the article

• How to use iSCSI inside HyperV VM?

  - by William

  I have 2 Dell R710 servers (intended to set up HyperV cluster) and a MD3000i SAN set up: Server1/Server2: NIC 1: connected to company LAN NIC 2: crossover to the other server's NIC 2 NIC 3: crossover to iSCSI port of SAN controller 1 NIC 4: crossover to iSCSI port of SAN controller 2 I have both servers setup as diskless servers with iSCSI boot from SAN without problem. But how can I access iSCSI from within the VM such that I can set up clustering inbetween the VMs? I can ping from the host to the SAN but found that NIC3/4 cannot be used for virtual network in HyperV? What am I doing wrong?

  Read the article

• internal DNS server limiting the speed as 55kb/sec ?

  - by kartook

  Hi all , Thanks in advance to everyone . Here is my Question . 1 .We have LAN internal DNS server ( 192.168.205.200 ) 2. DNS server Running on my ADDITIONAL DOMAIN CONTROLLER 3. Tested with Nslookup IPADDRESS and hostname resolving without any error . 4 .DHCP server Running on 3750 Switch ( Checked with CISCO Confirmed the configuration ) .DNS name server pointed to 192.168.205.200 . ISSUE : 1.Host getting ipaddress and DNS from DHCP server .Maximum file transfer Bandwidth 55KB/sec . 2. Assigned Static DNS on Host as ISP DNSServer Address, host getting full bandwidth whihc is 1mb/sec Thanks Kartook

  Read the article

• Linux Router - Share bandwidth per IPs with current active connections

  - by SRoe

  We have a Linux machine running as a custom router, currently utilising Shorewall. This sits between our incoming internet connection and the internal LAN. What we would like to achieve is 'fair use' of the bandwidth on a per IP basis. If only one person currently has an active connection then they get 100% utilisation of the line. However if 20 people have active connections then they should each get 5% utilisation of the line. This should be irrespective of the number of connections held by each user. For example, say we have two users, Bill and Ted, that both have active connections. Bill has a single active connection while Ted has ten active connections. Bill should get 50% utilisation for his single connections whilst Ted should get 5% utilisation for each of his ten connections, giving Ted a total utilisation of 50%.

  Read the article

• Cisco asa 5505 locks up / unresponsive

  - by Chris

  We have a cisco asa 5505 that's new (in service for about 2 months) running 7.2(4) software. Every day around 10a it locks up for approx 10 minutes. We're monitoring it via snmp with stg, and snmp doesn't respond during that time. There's no output in the 'show crash' output. Internet connectivity is also dropped. Wondering if anyone else has seen this and what the fix might be. Currently we're looking at upgrading software, but will need memory upgrade for that. We've forced the speed and duplex on the internal and external interfaces, but the problem is still occurring. It's connected on the internal lan to a netgear 724 gige switch.

  Read the article

• What are the "must " security tools for small organizations ?

  - by Berkay

  One of my friend has started a company, it's a small-scale company that has a 40 workers.There is two guys also responsible for the security and IT related issues.He is managing the LAN, Webpage of the company, e-mail configuration, printer hardware modification, application deployment etc. In this point, to provide the security measures including access controls, authentication, web server security etc. Which tools do you use for securing, monitoring and controlling the system ? Are you paying for these tools or are they open source? This question is due to the security administrators requests to my friend.He offers to get some tools for the company and my friend hesitates to pay that much on them (what he mentioned me.)

  Read the article

• VPN using Zywall

  - by Rune FS

  I've played around with a certificate based VPN (normally I don't do hardware) we've manged to setup the connection and the tunnel between the routers is working correctly. We now need the last step. There's no connection to the computers on the other end. What could we have forgotten? (we're testing with two standard configured Win7 machines) EDIT: Just to clarify the tunnel is working I can ping the router on the other end. I can't access the computers on the other side of that router and vice versa. (It's also possible to access the remotemangement console of the remote router on the LAN IP)

  Read the article

< Previous Page | 62 63 64 65 66 67 68 69 70 71 72 73  | Next Page >