Search Results

Search found 19350 results on 774 pages for 'address book'.

Page 665/774 | < Previous Page | 661 662 663 664 665 666 667 668 669 670 671 672 | Next Page >

System and Router configuration for setting up a home firewall based on Zentyal

- by Ako

I am not much of a system administrator, so please be patient if this looks too simple for you. I have a several computers at home, and all of them connect using an ADSL modem/router (and Wireless AP). I have been attacked several times (mainly from Russia and Ukraine), so I thought I should have some kind of firewall, besides the ESET firewall on my Windows 7. So now I have these (new) configuration: I have a small ADSL modem (Zyxel brand) which has only one Ethernet port. This modem is used to connect to internet and is configured in NAT mode. The interface has is configured with IP address 192.168.1.1. I have an old PC and I have installed zentyal on it. It has two Ethernet ports, eth0 and eth1. Eth0 is connected to the Zyxel modem with IP 192.168.1.2 and is checked as the WAN interface (external). I have another ADSL modem which is also a router with 4 Ethernet ports and Wireless AP. One of the Ethernet ports is connected to eth1 on Zentyal box. The Ethernet port's IP is 192.168.2.1 and Zentyal's eth1 is 192.168.2.2. Now, I want to enable other computers to connect to internet through the router both using Wireless and Ethernet. The problem is that I don't know how to configure the router so it routes connections to the Zentyal box. Does anyone have any clue? Again I am sorry if this looks stupid. Thanks.

Read the article
Can't get subdomain to point to working collabNet server - what am I doing wrong?

- by Jared

Hello everyone, I am running a web server using CollabNet SubVersion EDGE. You can view it at 71.13.105DOT51 I also run another website, http://www.tutorialcraft.com. I went into my Cpanel, and created a DNS record as follows: svn.tutorialcraft.com. 14400 IN A 71.13.105.51 Yet, if you go to http://svn.tutorialcraft.com, it doesn't load. I tested to see if I was doing some wrong, so I created a ebay.tutorialcraft.com and pointed it to eBay servers, and it worked fine (it's not up now). Anyone have any ideas? Thanks UPDATE NOTES: I tried to point svn.tutorialcraft.com to my original IP address (the one that www.tutorialcraft.com is pointed to, and it still won't load. Also, may be worthy of note, I am running a wordpress multi-site server, and I have disabled blog redirection. Here is a sample of my .htaccess as well: RewriteEngine On RewriteCond %{HTTP_HOST} ^tutorialcraft\.com RewriteRule (.*) http://www.tutorialcraft.com/$1 [R=301,L] RewriteBase / RewriteRule ^index\.php$ - [L] # uploaded files RewriteRule ^files/(.+) wp-includes/ms-files.php?file=$1 [L] RewriteCond %{REQUEST_FILENAME} -f [OR] RewriteCond %{REQUEST_FILENAME} -d RewriteRule ^ - [L] RewriteRule . index.php [L]

Read the article
Access server using IP on another interface

- by Markos

I am using Windows Server 2012 instead of a router for my home network. Currently I am using RRAS and computers from local network can access Internet correctly. Here is a map of the current setup: [PC1] ---| |---- (lan ip)[Server](wan ip)--> internet [PC2] ---| I have applications running on Server, such as IIS and others. All can be accessed from internet using wan ip and from lan using lan ip. I have a domain, lets say its my-domain.com, which is resolved to my wan ip. What I want is to enable my LAN computers to be able to connect to services on my server using the very same address as internet users: eg http://my-domain.com/. However this does not work for my lan computers. What I understand is that I need to set up some kind of loopback route in a way that packets comming to LAN interface get routed to WAN interface. But I haven't found how to achieve this (in fact, I don't know WHAT to search for). Feel free to ask for additional informations and I will try to update the question.

Read the article
Router intermittently failing

- by nomen

My old Asus router died a few weeks ago, so I thought I'd set up my Debian box to deal with routing my home network. I have a few complications, but I adapted my configuration from a previously working configuration, and I don't see why I am having intermittent problems. But I am having them! Every so often, my SSH connections to the router (and to the Xen virtual machines hosted by the router) just drop. I am unable to use the router's dns server. I can't ping the router. Etc. All of these things work most of the time, but break down intermittently, for a few minutes at a time. (I can provide more details, but I'm not sure what will be helpful) /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # Gigabit ethernet, internal network auto eth0 allow-hotplug eth0 iface eth0 inet manual # USB ethernet, internet auto eth1 allow-hotplug eth1 iface eth1 inet dhcp # Xen Bridge auto xlan0 iface xlan0 inet static bridge_ports eth0 address 10.47.94.1 netmask 255.255.255.0 As I understand it, this is sufficient to create the network interfaces, and even do some switching between Xen hosts and my eth0 interface. I installed and configured Shorewall to manage routing between the bridge and my internet-facing interface: /etc/shorewall/zones fw firewall net ipv4 lan ipv4 /etc/shorewall/interfaces net eth1 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians lan xlan0 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians,routeback,bridge /etc/shorewall/policy net all DROP info fw net ACCEPT info all all REJECT info /etc/shorewall/rules DNS(ACCEPT) fw net DNS(ACCEPT) lan fw Ping(ACCEPT) lan fw ... and so on, these all work, when the router is accepting traffic at all. /etc/shorewall/masq eth1 10.47.94.0/24 Also, the router is currently "working", and I checked on a problematic client: arp infrastructure infrastructure.mydomain (10.47.94.1) at 0:23:54:bb:7d:ce on en0 ifscope [ethernet] I tried it when the router was down, and I (eventually) got the same response. It took about 30 seconds to return, though.

Read the article
How to configure default text selection behavior in Windows XP, 7? (eg. mouse click selects entire word vs. mouse click inserts an active cursor)

- by Mouse of Fury

I find the mouse click behavior of Windows XP and Windows 7 annoying and intrusive. I don't remember Windows NT being quite this bad, or MacOS 7 - 10 which I used in the nineties. When I'm using a browser and I click on a text field - for example, the address bar, or a search box - the first thing which happens is the entire field is selected.Subsequent clicks seem to select parts of words, often deciding arbitrarily to exclude or include adjacent punctuation. The same in Excel and other apps, and when trying to rename files, so I'm assuming this behavior comes from a system-wide text handling routine. I frequently want to edit text, cut out or replace odd parts of the insides of words or chunks of sentences, and often find that to get a simple cursor to insert I have to click the mouse up to 4 times in succession. I've had to do a lot of this recently and it has been driving me insane. Is there a place at the system level where this can be configured? In a perfect world, I'd like a single click on a new text area to insert a cursor point, and a rapid double click to select the entire area. Words or text within the area could be selected by inserting a cursor, holding down the mouse button and dragging to the exact point where I want the selection to end - even if that's in the middle of a word. No, I don't need or want Windows to "smart select" a word or sentence for me. I've looked in the Mouse and Accessibility Options control panels (Windows XP). Haven't found anything even close. Thanks -

Read the article
Windows 2008 R2 DHCP Overlapping Scopes

- by Buska

We are trying to troubleshoot a scope overlap problem. We have multiple device types we wish to give all different ranges of a 16 bit subnet. IE. X device we wish to give 192.168.2.1-192.168.2.254/16, Y devices we wish to give 192.168.3.1-192.168.3.254/16. We are trying to accomplish this by creating different scopes and using the 60 class identifier. The problem is DHCP won't allow us to give these scopes with 16 bit masks because of the potential overlap. We aren't overlapping the address pool so why does DHCP care and can we work around this? If this isn't possible, how can i assign specific ranges by device type without creating multiple scopes? Any thoughts would be helpful. UPDATE: Entire Scope is 192.168.0.0/16 Gateway is 192.168.1.1/16 Device Hardware A - 192.168.20.1-192.168.20.254/16 Device Hardware B - 192.168.26.1-192.168.26.254/16 Device Hardware C - 192.168.85.1-192.168.85.254/16 We tried to setup multiple scopes for each device type (A,B,C) but couldn't specify a 16 bit mask as Scope A could technically overlap Scope B even thought our start and end addresses don't. I hope this makes more sense. Thanks for your thoughts.

Read the article
DNS Zone file and virtual host question (repost because my question got moved and now I can't comment on the original for some reason)

- by Jake

Sorry this is a repost, the original question got moved to here form stack overflow and for some reason I can't comment or respond to answers on that one anymore. Hi all, I'm trying to set up a virtual host for redmine.SITENAME.com. I've edited the httpd.conf file and now I'm trying to edit my DNS settings. However, I'm not sure exactly what to do. Here's an snippet of what's already in the named.conf file (the file was made by someone else who is unreachable): zone "SITENAME.com" { type master; file "SITENAME.com"; allow-transfer { ip.address.here.00; common-allow-transfer; }; }; I figure if I want to get redmine.SITENAME.com working, I need to copy that entry and just replace SITENAME.com with redmine.SITENAME.com but will that work? I was under the impression I needed a .db file but I don't see any reference to one in the current named.conf file. I also don't see any .db files or files named SITENAME in named.conf's directory. Any ideas where these illusive pre-existing db files could be?

Read the article
Can't access random web pages on my MacBook Pro 2012?

- by Faruk Sahin

Sometimes I can't access random web pages. The page simply doesn't load. If I wait for around a minute doing nothing, it will load. It happens very random and very intermittent. Sometimes it starts when I try to access youtube.com or cnn.com. When it starts, it happens once in a minute or once in 5 minutes for random web pages. But if I am downloading something, the download continues without any interruption. And also I am able to ping the address I can't browse. Then if I wait for around a minute, everything starts to work fine at the browser side also. I have tried a lot of different browsers. I have tried changing my DNS servers to Google's public DNS servers. Using a cable instead of the wireless connection doesn't work either. No one else in the network has this problem, but me. What can be the problem?

Read the article
Apache mod_proxy

- by mhouston100

Uggh, I'm spewing that I can't figure this out, I'm so frustrated: <VirtualHost *:80> servername domain1.com.au ServerAdmin webmaster@localhost DocumentRoot /var/www/html ErrorLog ${APACHE_LOG_DIR}/error.log CustomLog ${APACHE_LOG_DIR}/access.log combined <Proxy *> Order Allow,Deny Allow from all </Proxy> RewriteEngine on ReWriteCond %{SERVER_PORT} !^443$ RewriteRule ^/(.*) https://%{HTTP_HOST}/$1 [NC,R,L] </VirtualHost> <VirtualHost *:443> servername domain1.com.au SSLEngine on SSLCertificateFile /etc/apache2/ssl/owncloud.pem SSLCertificateKeyFile /etc/apache2/ssl/owncloud.key DocumentRoot /var/www/html </VirtualHost> <VirtualHost *:*> Servername domain2.com.au ProxyRequests Off <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass / https://192.168.1.12/ ProxyPassReverse / https://192.168.1.12/ </VirtualHost> Not sure if it's clear what I'm trying to do, but I've read and read and READ, I still can't figure it out. Basically I have a working Apache server with a rewrite to force HTTPS, as seen in the first two VirtualHost entries. I now have a webmail service I set up on another server, under another domain name, however I only have one incoming public IP address. So I'm trying to have any incoming requests for the second domain to be proxied to the other server to access the webmail, whether its port 80 or 443. IMAP and POP3 are no problems, I can just forward the ports directly to the correct server. The results of the above configuration is that requests to domain2.com.au (port 80 or 443) are forwarded to https://domain1.com.au. Am I headed in the right direction?

Read the article
How can I change the binding order of network adapters in Windows 7?

- by Chris Farmer

The end goal here is that I am trying to install an Oracle 10g server on my Windows 7 x64 dev box. I use DHCP, and the Oracle installer is throwing up this warning: Checking Network Configuration requirements ... Check complete. The overall result of this check is: Failed <<<< Problem: The install has detected that the primary IP address of the system is DHCP-assigned. Recommendation: Oracle supports installations on systems with DHCP-assigned IP addresses; However, before you can do this, you must configure the Microsoft LoopBack Adapter to be the primary network adapter on the system. See the Installation Guide for more details on installing the software on systems configured with DHCP. I have installed the loopback adapter, but I am not sure how to make it the primary network adapter. I see this Microsoft KB article on the subject but it's Windows XP-oriented, and I can't seem to find a comparable one for Windows 7. Some of the options it talks about don't seem to be present in the views of the adapters that I see. So, how can I make the loopback adapter become the primary adapter?

Read the article
Restrict Computer or Users from Internet but allow access to intranet and Windows Update / ePO?

- by MoSiAc

So this may be impossible but I've been asked to try and find something about it. So far nothing I have found is possible. I need to restrict specific machines or user accounts from regular Internet access but let them have access to the intranet portion of our network. I do not have Active Directory control, nor does anyone at my local workplace (corporate control in a different state). I have tried going through IPsec and doing this per local machine, but that system seems to have been removed from the images that are installed on these machines so that is out. So far the only other option I can think of is assigning the machines a specific ip address and removing their gateway access. This would probably work but the machines need to be able to receive updates that are being pushed to them through ePO and LanDesk. I would really like to do this on the user level because then if I need to do tech work to the machine and need internet access I can get to it but a "special" user could login and not be able to get into anything.

Read the article
Looking for easiest, most simple solution to run a customised DNS Server for my local network on Windows 7.

- by Jamie G

I need to forward some websites, such as http://testing.server/ to an fixed IP address on my local network. I can do this easily on one computer using the hosts file. However, I need this to work for all machines on my network. I think the best way to do this will be to setup my own DNS Servers and add the custom DNS settings there. However, I'm looking for the simplest way possible to do this - I really don't want to spend hours setting up Unix Servers and running tricky terminal based scripts just to do this! My server is a standard Windows 7 machine. My dream would be a nice simple windows program with a GUI where I could input my ISP's DNS server and it would use those records, unless I had specifically set up my own DNS for a domain to use instead. If it had a web based admin system that was accessible from another computer on the network that would be even better. Does anyone know of anything that can do this? Many thanks indeed.

Read the article
Strange ssh login

- by Hikaru

I am running debian server and i have received a strange email warning about ssh login It says, that user mail logged in using ssh from remote address: Environment info: USER=mail SSH_CLIENT=92.46.127.173 40814 22 MAIL=/var/mail/mail HOME=/var/mail SSH_TTY=/dev/pts/7 LOGNAME=mail TERM=xterm PATH=/usr/local/bin:/usr/bin:/bin:/usr/bin/X11:/usr/games LANG=en_US.UTF-8 SHELL=/bin/sh KRB5CCNAME=FILE:/tmp/krb5cc_8 PWD=/var/mail SSH_CONNECTION=92.46.127.173 40814 my-ip-here 22 I looked in /etc/shadow and find out, that password for is not set mail:*:15316:0:99999:7::: I found this lines for login in auth.log n 3 02:57:09 gw sshd[2090]: pam_winbind(sshd:auth): getting password (0x00000388) Jun 3 02:57:09 gw sshd[2090]: pam_winbind(sshd:auth): pam_get_item returned a password Jun 3 02:57:09 gw sshd[2091]: pam_winbind(sshd:auth): user 'mail' granted access Jun 3 02:57:09 gw sshd[2091]: Accepted password for mail from 92.46.127.173 port 45194 ssh2 Jun 3 02:57:09 gw sshd[2091]: pam_unix(sshd:session): session opened for user mail by (uid=0) Jun 3 02:57:10 gw CRON[2051]: pam_unix(cron:session): session closed for user root and lots of auth failures for this user. There is no lines with COMMAND string for this user. Nothing was found with "rkhunter" and with "ps aux" process inspection, also there is no suspicious connections was found with "netstat" (as I can see) Can anyone tell me how it is possible and what else should be done? Thanks in advance.

Read the article
Host Name Resolution - ISA 2006 - VPN PPTP

- by Brian Lee Jackson

We are running an ISA 2006 server and PPTP VPN connection works fine. Clients are able to connect to internet, access Outlook, CRM, etc. The problem we are encountering is that host name resolution is not working. Example, when connected via VPN I can’t ping any box other than the VPN server by the host name. Nslookup also fails. I can ping everything fine via IP address. But for clients, they need to be able to access their “mapped” drives over the VPN which all are mapped by host name. I recently took over this position and it sounds like this used to work. What would be the best place to check first? I haven’t had much exposure to ISA and have been reading up a bit on installation procedures, etc. DNS is hosted and running on our domain controller, as well as WINS. It isn’t on the ISA box. Is there a firewall policy that perhaps got removed? What usually is required for host name resolution to pass through. Any help would be appreciated, thanks!

Read the article
Offloading backups to secondary network

- by user1467163

I'm trying to solve a problem- Currently, we are constantly backing up and have no budget for additional servers. Our production network is still a 10/100 and handles voip, SQL plus our backup traffic, and I'd like to offload the backup traffic onto a secondary network- all of our servers have secondary NIC's that are not in use, and all support gigabit (Our switching hardware does not- a topic for another day). I'd like to move my backups off the production network, but I am having a hard time getting the computers to communicate. I am using a Netgear GS724T switch for the backup network- Chosen for cost and because I have used them extensively on networks saturated with ghosting traffic, so I know it's up to the task. I have defined a VLAN, with ports that are not members of any other VLAN. All traffic is untagged on the VLAN. I have set the servers with 192.168.1.10 and 192.168.1.11 addresses, 255.255.255.0 netmask and I have tried a blank GW, using the local IP of the server 192.168.1.whatever address, and I have tried using the switch's production-side IP as the GW. The machines cannot find each other. DNS addresses are blank because I am going purely by IP for now... Any ideas how to get these machines to talk? they are Windows machines, running Server 2008R2 and 2003R2. Thanks!

Read the article
trying to route between two openvpn clients

- by user42055

I have two openvpn clients on the 10.0.1.0 (client1) and 192.168.0.0 (client2) subnets with the server's openvpn connection having the ip 192.168.150.1 The server has ip forwarding enabled. Currently, client1's vpn ip is 192.168.150.10 and the P-t-P ip is 192.168.150.9 I have created the following static route on client1: route add -net 10.0.1.0 netmask 255.255.255.0 gw 192.168.150.9 The routing table on client1 looks like this: Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.150.9 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 192.168.150.1 192.168.150.9 255.255.255.255 UGH 0 0 0 tun0 10.0.1.0 192.168.150.9 255.255.255.0 UG 0 0 0 tun0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 I thought this would be correct to allow traffic from client1 to reach computers on client2's network, but it does not work. Is 192.168.150.9 (the P-t-P address) the correct one to be routing through ? I tried using 192.168.150.1 but I couldn't create the route. I hope this is clear.

Read the article
Not able to connect to port different than 22 - OpenVPN

- by t8h7gu

I have OpenVPN network with 5 clients. Computer with Arch Linux which hosts OpenVPN server, It also hosts virtual machine with Computer with CentOS which is also connnected to OpenVPN subnet. Windows 8 which hosts virtual machine with CentOS. Both of them are connected to OpenVPN. Last one machine is virtual machine with CentOS which is hosted by computer with Ubuntu 14( which is not connected to OpenVPN. All machines in OpenVPN subnet are bolded. All phisical computers are in different networks. The problem is that when I use nmap to scan Windows and it's guest virtual machine it's saids that host seems down. When I force namp to scan specific port it shows filtered state: nmap -Pn -p 50010 n3 Starting Nmap 6.46 ( http://nmap.org ) at 2014-06-07 19:49 CEST Nmap scan report for n3 (10.8.0.3) Host is up (0.11s latency). rDNS record for 10.8.0.3: node3.com PORT STATE SERVICE 50010/tcp filtered unknown Telnet also cannot connect to this port telnet n3 50010 Trying 10.8.0.3... telnet: Unable to connect to remote host: No route to host But ss on this host show's proper state of this port ss -anp | grep 50010 LISTEN 0 50 10.8.0.3:50010 *:* users:(("java",12310,271)) What might be possible reason of that and how to fix it? EDIT I've found that I am able to connect via telnet to ssh port: telnet n3 22 Trying 10.8.0.3... Connected to n3. Escape character is '^]'. SSH-2.0-OpenSSH_5.3 So it seems that it's not problem with Windows firewall. But I have no idea what it might be. Also nmap result for first thousand ports: nmap -Pn -p 1-1000 n3 Starting Nmap 6.46 ( http://nmap.org ) at 2014-06-07 20:08 CEST Nmap scan report for n3 (10.8.0.3) Host is up (0.49s latency). rDNS record for 10.8.0.3: node3.com Not shown: 999 filtered ports PORT STATE SERVICE 22/tcp open ssh Nmap done: 1 IP address (1 host up) scanned in 77.87 seconds

Read the article
bond0:0 + define virtual IP

- by yael

in my Linux server I have the following: Linux Version - RedHat-Linux- 5.3.0.0 (this Linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it possible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

Read the article
Wireless Access Point stopped working

- by Alex Pritchard

I have a simple LAN set up at home using a Linksys WRT54GSV4 as my primary router and an Encore ENHWI-2AN3 as an access point. I connect the Encore to the Linksys by running a cable from one of the Linksys LAN ports into the Encore WAN input. I originally configured this using the Encore setup wizard, setting the device up in AP Router Mode. It detected the input network and worked about as expected, creating a second network that used my primary network to connect to the internet. It worked fine for about 2 weeks, then abruptly cut out today. I checked to make sure the network was still live through the cable going into the Encore (provides internet when connected to a laptop directly) and that devices are still able to connect to the network being broadcast by the Encore. When I try to rerun the connection wizard on the Encore, I receive the message "No Services found in WAN port." The WAN Settings is no longer retrieving a dynamic ip from the line. I tried providing a static IP, assigning an IP address within the subnet range of my primary router that wasn't being used and pointing the Default Gateway to the Linksys IP, but this did not work either. When I plug the cable into the WAN port, an internet light comes on that is not lit when a live network is not connected. I've tried doing a hard reset on the Encore (held down the rest button until the lights flashed, reconfigured from scratch), but the WAN settings are still not detected. Also tried powering off and on the modem, linksys, and encore. Any suggestions would be appreciated!

Read the article
Using Computer name in URL causes issues when connecting to Web Services

- by AWinters

The set of applications I work on all access the same 8 or so web services that we have. These services and applications all reside on the same box and all use the computer name when trying to connect to the web service. For Example: If I have a web service called MapDataService and I have an application that accesses it, it would access it by the URL: http://COMPUTERNAME/MapDataService/MapDataService.asmx. This works in most of the applications that access the web service. However, we have several applications that, when using the computer name in the URL, will not get data returned from the service (actually a 503 is returned). In order to get it to work, the IP address of the system needs to be used in place of the COMPUTERNAME. This strikes me as very odd considering, as I mentioned before, all applications and services are on the same box and most other applications usr the COMPUTERNAME with no issues. Can someone give me some insight as to what could be causing this? We have no access to IIS logs and what logs we did get (this is on a customer site) are not very useful.

Read the article
.htaccess modify rules and redirect if there's .php in the url

- by Ron

Hello everyone. I got the following code in my .htaccess: Options +FollowSymlinks RewriteBase /temp/test/ RewriteEngine on RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_FILENAME}\.php -f RewriteRule ^about/(.*)/$ $1.php [L] RewriteRule ^(.*)/download/(.*)/(.*)/(.*)/downloadfile/$ file-download.php?product=$1&version=$2&os=$3&method=$4 [L] RewriteRule ^(.*)/download/(.*)/(.*)/(.*)/$ download-donate.php?product=$1&version=$2&os=$3&method=$4 [L] RewriteRule ^(.*)/download/(.*)/$ download.php?product=$1&version=$2 [L] RewriteRule ^newsletter-confirm/(.*)/$ newsletter-confirm.php?email=$1 [L] RewriteRule ^newsletter-remove/(.*)/$ newsletter-remove.php?email=$1 [L] RewriteRule ^(.*)/screenshots/$ screenshots.php?product=$1 [L] RewriteRule ^(.*)/(.*)/$ products.php?product=$1&page=$2 [L] RewriteRule ^schedule-manager/$ products.php?product=schedule-manager&page=view [L] RewriteRule ^visual-command-line/$ products.php?product=visual-command-line&page=view [L] RewriteRule ^windows-hider/$ products.php?product=windows-hider&page=view [L] RewriteRule ^(.*)/$ $1.php [L] RewriteRule ^products/$ products.php [L] everything work perfect. I would like to know how can I modify it so it will be less lines. I am pretty sure I can atleast remove 4-5 lines, but I dont know how. (merge the schedule-manager, visual-command-line and windows-hider, and some more). I know that the order of the rules is important, this order works - although I have no idea why, I just played with the rules until it worked. If you think that there'll be a bug with the following order please tell me where. Another thing - I would like to redirect for example www.myweb.com/products.php to www.myweb.com/products/ (I mean that the URL in the address bar will change). I dont know if the redirect can go along with my rewrite rules. Thank you.

Read the article
Host couldn't be reached by domain name, only by IP: Apache's fault?

- by MaxArt

I have this Windows Server 2003 R2 32 bit machine running Apache 2.4.2 with OpenSSL 1.0.1c and PHP 5.4.5 via mod_fcgid 2.3.7. This config worked just fine for some hours, but then the site couldn't be reached with its domain name, say www.example.com, but it could be still reached by its IP address. In particular, while https://www.example.com/ yielded a connection error, http://123.1.2.3/ worked just fine. Yes, first https then http. Error and access logs were clean, i.e. they showed no signs of problems. Just the usual messages, that were interrupted while the site couldn't be reached. After some investigation, a simple restart of Apache solved the problem. Unfortunately, I didn't have the chance to test if https://123.1.2.3/ worked as well, or if http://www.example.com/ was still redirected to https as usual. So, has anyone have any idea of what happened? Before I get tired of Apache and ditch it in favor of Nginx? Edit: Some log informations. The last line of sslerror.log is from 90 minutes before the problem occurred, so I guess it's not important. ssl_request.log shows nothing interesting, too: these are the last two lines before the problem: [28/Aug/2012:17:47:54 +0200] x.x.x.x TLSv1.1 ECDHE-RSA-AES256-SHA "GET /login HTTP/1.1" 1183 [28/Aug/2012:17:47:45 +0200] y.y.y.y TLSv1 ECDHE-RSA-AES256-SHA "POST /upf HTTP/1.1" 73 The previous lines are all the same and don't seem interesting, except 4 lines like these 30-40 seconds before the problem: [28/Aug/2012:17:47:14 +0200] z.z.z.z TLSv1 ECDHE-RSA-AES256-SHA "-" - These are the corrisponding lines from sslaccess.log: z.z.z.z - - [28/Aug/2012:17:47:14 +0200] "-" 408 - ... x.x.x.x - - [28/Aug/2012:17:47:54 +0200] "GET /login HTTP/1.1" 200 1183 y.y.y.y - - [28/Aug/2012:17:47:45 +0200] "POST /upf HTTP/1.1" 200 73

Read the article
Does migrating 2 domain controllers between 2 datacentre requires both virtual machines to be shut down at the same time?

- by Imagineer

I was attempting to migrate 2 virtual machines that are domain controllers between 2 datacentres running ESX 3.5 and ESX 4.1. I was advised to shut down both domain controller at the same time during the migration process. This is to avoid USN Rollback and other replication issues. The following are the steps that I was planning to perform: 1. Shutdown both DC. 2. Copy both VMs files across to new datacentre using Veeam FastSCP (connection to both vCentre through IP address instead of hostname) 3. Power them up at new datacentre. 4. Configure Network interface/DNS/DHCP for both DCs in new datacentre I have tried to use Veeam FastSCP rather than VMware Standalone Converter is because its copying rather than converting. Someone also suggested that I use backup and restore app like Veeam backup and replication software. Sounds like a simple job, but after shutting down both DCs, the transfer rate using FastSCP is so slow registering only 1KB/s as oppose to the normal 1MB/s (or more). When that attempt to transfer failed, I tried to cold clone both DCs resulted in the both ESX hosts get disconnected. I have tried troubleshooting by referring to this - VMware KB - Diagnosing an ESX Server that is Disconnected or Not Responding in VirtualCenter It seems that the DNS being down is the caused of all unusual occurrence. The moment I powered up the DCs via VMware console command, the ESX host were able to connect to the vCentre again. How can I avoid such a pitfall again? Am I doing it correctly? Any help would be greatly appreciated! Thank you.

Read the article
Host ::1 resolves to remote IP

- by thebuckst0p

/etc/hosts files usually have this line, ::1 localhost. I thought ::1 was the equivalent of 127.0.0.1/localhost, and from my reading it seems to be the IPv6 version. So I was using it in Apache for firewalling, "Allow from ::1" and it only allowed local. Then suddenly that stopped working, so I pinged ::1 and got a remote IP address. I tracerouted it and it went through my ISP, through some Microsoft server, then another half dozen steps of asterisks... I'm not sure why this would be (the remote IP), but it doesn't seem good. I grep'd my hard drive for the remote IP and it doesn't appear anywhere. Is this some indicator that I'm being hacked, or normal behavior? Maybe my IPv6 settings are wrong? (This is a brand new MacBookPro with Snow Leopard.) Any ideas about this would be great - what is ::1 supposed to be, why would it be remote, should I be worried, how do I get it back to localhost? Thank you!

Read the article
Failed none and iptables

- by Michael

The problem is that when I ssh to my host with putty and enter user name, after that the password prompt delays. Found this is directly related to my iptables and can solve by changing default policy to ACCEPT. If default INPUT policy is ACCEPT, then password prompt is coming immediately. Mar 13 00:05:01 server-ubuntu sshd[6154]: Connection from 192.168.0.10 port 26304 Mar 13 00:05:06 server-ubuntu sshd[6154]: Failed none for acid from 192.168.0.10 port 26304 ssh2 However, if default INPUT policy is DROP, I got slight delay in getting password prompt after I enter username Mar 13 00:07:12 server-ubuntu sshd[6177]: Connection from 192.168.0.10 port 26333 Mar 13 00:07:35 server-ubuntu sshd[6177]: Failed none for acid from 192.168.0.10 port 26333 ssh2 For the second case, I tried to set default policy for FORWARD and OUTPUT chains to ACCEPT, but it didn't help. The only rule in this case is: -A INPUT -i eth1 -m mac --mac-source 00:26:XX:XX:XX:XX -j ACCEPT 00:26:XX:XX:XX:XX is the mac address from which I am trying to ssh to server's LAN(eth1). I'm sure there has to be some rule, which I can use while default INPUT chain policy is DENY in order to get password prompt immediately. I realize that the error message in the log is something normal and part of some verification procedure.

Read the article

< Previous Page | 661 662 663 664 665 666 667 668 669 670 671 672 | Next Page >