Search Results

Search found 19350 results on 774 pages for 'address book'.

Page 666/774 | < Previous Page | 662 663 664 665 666 667 668 669 670 671 672 673  | Next Page >

• SSH Connection Error : No route to host

  - by dewbot

  There are three machines in this scenario: Desktop A : [email protected] Laptop A : [email protected] Machine B : [email protected] All the machines have Ubuntu 11.04 (Desktop A is a 64bit one) and have both openssh-server and openssh-client. Now when I try to connect Desktop A to Laptop A or vice-versa by ssh [email protected] I get an error as port 22: No route to host in both the cases. I own both the machines, now if I try same commands from my friend's machine, i.e. via Desktop B, I can access both my Laptop and Desktop. But if I try to access Desktop B from my Laptop or by Desktop I get port 22: Connection timed out I even tried changing ssh port no. in ssh_config file but no success. Note: that 'Laptop A' uses WiFi connection while 'Machine A' uses Ethernet Connection and 'Machine B' is on an entirely different network. Laptop A && Desktop A - Router/Nano_Rcvr provided to me by ISP. So to one Router two Machines are connected and can be accessed at the same time. here is my ifconfig output for both the machines :- Laptop wlan0 Link encap:Ethernet HWaddr X:X:X:X:00:bc inet addr:1.23.73.111 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::219:e3ff:fe04:bc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:108409 errors:0 dropped:0 overruns:0 frame:0 TX packets:82523 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:44974080 (44.9 MB) TX bytes:22973031 (22.9 MB) Desktop eth0 Link encap:Ethernet HWaddr X:X:X:X:c5:78 inet addr:1.23.68.209 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::227:eff:fe04:c578/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10380 errors:0 dropped:0 overruns:0 frame:0 TX packets:4509 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1790366 (1.7 MB) TX bytes:852877 (852.8 KB) Interrupt:43 Base address:0x2000

  Read the article

• VirtualBox with Ubuntu Server guest can't ping outside

  - by Danidan

  Here's my situation: an Ubuntu 12.04 Host running VirtualBox; two guest VMs running Ubuntu Server 12.04 home network, so my Host pc has a wireless connection to the router of my ISP. My problem is in one of the virtual machines: it has 3 NICs, one in NAT mode and the others in Host Only mode. My purpose is to use eth0 (NAT) for Internet access and eth1, eth2 (Host Only) for management of internal virtual network (eth1 uses a VBoxNet with this IP 192.168.69.254). Whenever I try to $ping 8.8.8.8 I get Destination Host Unreachable. While if I $ping 192.168.69.10, that is the IP of the other VM, it works. I can't also ping my Host nor my router My /etc/network/interfaces file is: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp auto eth1 iface eth1 inet static address 192.168.69.1 netmask 255.255.255.0 auto eth2 iface ifconfig $IFACE 0.0.0.0 up up ip link set $IFACE promisc on down ip link set $IFASE promisc off down ifconfig $IFACE down $route -n returns: Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 10.0.2.2 0.0.0.0 UG 100 0 0 eth0 10.0.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.69.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0 Forgetting for now what eth2 needs to do and its setup, why I can't go outside the Host box? What can I do to help you helping me? :-)

  Read the article

• Strange problem with Google Mail and IMAP on Outlook 2007

  - by Alex C.

  I work for a small non-profit organization. We have about 35 administrative employees who use e-mail. We're on a Windows network with a domain. Everyone is running XP Pro and Office 2007 with all updates/patches. We used to use POP3 mail through a local provider. However, we recently signed-up for a free Google Apps account, and we switched to IMAP mail through Google. Everyone uses Outlook 2007 as the client. For about ten days, everything was working fine. Yesterday afternoon, we suddenly developed a strange and annoying problem. Every time you send an e-mail message, a copy of your outgoing message shows up in your inbox. It's as if you're adding your own address to the CC: line of every message. Nothing has changed on our end. I was hoping that the problem was a temporary glitch that would resolve itself, but here we are about 24 hours later, and it's still happening. I searched Twitter, and there were a handful of vague messages about issues with Google mail and IMAP, but I didn't see any references to this specific problem. Any thoughts on what's going on here and how to fix it?

  Read the article

• Host ::1 resolves to remote IP

  - by thebuckst0p

  /etc/hosts files usually have this line, ::1 localhost. I thought ::1 was the equivalent of 127.0.0.1/localhost, and from my reading it seems to be the IPv6 version. So I was using it in Apache for firewalling, "Allow from ::1" and it only allowed local. Then suddenly that stopped working, so I pinged ::1 and got a remote IP address. I tracerouted it and it went through my ISP, through some Microsoft server, then another half dozen steps of asterisks... I'm not sure why this would be (the remote IP), but it doesn't seem good. I grep'd my hard drive for the remote IP and it doesn't appear anywhere. Is this some indicator that I'm being hacked, or normal behavior? Maybe my IPv6 settings are wrong? (This is a brand new MacBookPro with Snow Leopard.) Any ideas about this would be great - what is ::1 supposed to be, why would it be remote, should I be worried, how do I get it back to localhost? Thank you!

  Read the article

• .htaccess modify rules and redirect if there's .php in the url

  - by Ron

  Hello everyone. I got the following code in my .htaccess: Options +FollowSymlinks RewriteBase /temp/test/ RewriteEngine on RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_FILENAME}\.php -f RewriteRule ^about/(.*)/$ $1.php [L] RewriteRule ^(.*)/download/(.*)/(.*)/(.*)/downloadfile/$ file-download.php?product=$1&version=$2&os=$3&method=$4 [L] RewriteRule ^(.*)/download/(.*)/(.*)/(.*)/$ download-donate.php?product=$1&version=$2&os=$3&method=$4 [L] RewriteRule ^(.*)/download/(.*)/$ download.php?product=$1&version=$2 [L] RewriteRule ^newsletter-confirm/(.*)/$ newsletter-confirm.php?email=$1 [L] RewriteRule ^newsletter-remove/(.*)/$ newsletter-remove.php?email=$1 [L] RewriteRule ^(.*)/screenshots/$ screenshots.php?product=$1 [L] RewriteRule ^(.*)/(.*)/$ products.php?product=$1&page=$2 [L] RewriteRule ^schedule-manager/$ products.php?product=schedule-manager&page=view [L] RewriteRule ^visual-command-line/$ products.php?product=visual-command-line&page=view [L] RewriteRule ^windows-hider/$ products.php?product=windows-hider&page=view [L] RewriteRule ^(.*)/$ $1.php [L] RewriteRule ^products/$ products.php [L] everything work perfect. I would like to know how can I modify it so it will be less lines. I am pretty sure I can atleast remove 4-5 lines, but I dont know how. (merge the schedule-manager, visual-command-line and windows-hider, and some more). I know that the order of the rules is important, this order works - although I have no idea why, I just played with the rules until it worked. If you think that there'll be a bug with the following order please tell me where. Another thing - I would like to redirect for example www.myweb.com/products.php to www.myweb.com/products/ (I mean that the URL in the address bar will change). I dont know if the redirect can go along with my rewrite rules. Thank you.

  Read the article

• Pinging computer name in LAN results in public IP?

  - by Bob

  Hi, I recently introduced a new machine to my LAN. The computer name for this machine is 'server'. Historically I've been able to access machines from my home network (from a web browser or RDP) using the machine name and it resolves to a local IP address just fine. However, I can't seem to do this anymore. When I ping the computer name, I get the following: C:\Users\Robert>ping server Pinging server.router [67.215.65.132] with 32 bytes of data: Reply from 67.215.65.132: bytes=32 time=24ms TTL=54 Reply from 67.215.65.132: bytes=32 time=23ms TTL=54 Reply from 67.215.65.132: bytes=32 time=24ms TTL=54 Reply from 67.215.65.132: bytes=32 time=24ms TTL=54 I notice also that it appends the 'router' suffix to my domain name for some reason. 'router' is the name of my router, obviously. I'm also using OpenDNS as my DNS provider (configured through my router so it gets passed down through DHCP). Why is this not working for me? Can someone explain how the DNS resolution should take place? For LAN resolution, it shouldn't go straight to OpenDNS. I thought that each Windows machine kept it's own sort of "mini DNS server" that knows about all machines on the local network and it first tries to resolve using that. Please let me know what I can do to get this working!

  Read the article

• what is the reason behind window service stopped ,whether its due to LAN problems or any other issues

  - by Steve

  I have a windowservice which named Trunk which stopped one day i just want to know the reason behind it? this is an entry in the logs, Nov 15 17:54:04.318 :Trunk-1516:Trunk:handle_control_event:Received CTRL_LOGOFF_EVENT, ignore it Nov 25 15:54:52.157 :Trunk-1516:Trunk:ERROR - Process Restart Count (5) Exceeded for:C:\Program Files\secon\11.1.4\bin\vmd Nov 25 15:54:52.157 :Trunk-1516:Trunk:Stopping Trunk ... Nov 25 15:54:52.314 :Trunk-1516:Trunk:Shutting down, signaled C:\Program F Nov 20 15:54:20.345 :SCBridge.RegisterBridge:Exception in method: ScUtility.ScCommandException (0xa08990002): Exception from HRESULT: 0xa08990002 Supplemental Information: None available. at ScServer.ScServiceProcessorRegistryManager.Attach(String serviceProcessor, ScClientInformation clientInfo, FORCE_ATTACH_SPEC forceAttachToMaster) at ScServer.ScServiceProcessorRegistry.Attach(String serviceProcessor, Object clientInfo) at ScServer.ScServiceProcessorRegistry.Attach(String serviceProcessor) at ServerControlInterface.SCBridge.RegisterBridge(String SPName) for system APOLLOSP0 attempting to attach and register with the Bridge i had seen service is registered with specific account, so i thought that user logged off from the machine that may be the reason behind it or any LAN disconnection problem . But Having taken another look at the above entry we seem to have a constant failure being generated in vmd which causes Trunk to detect vmd requires a restart. Most of the time it works OK and the restart count is anything up to 4. In this case the Trunk log confirms that the Restart Count is 5 and so is considered to be exceeded. Presumably, this triggers the termination of the other services and Trunk is actually doing its job.So, coould this just be a timing issue and we need to increase the tolerance level (i.e restart count) or do we need to address the 0xa08990002 error in vmd?

  Read the article

• Developer hardware autonomy in a managed desktop environment [closed]

  - by Troy Hunt

  I’m looking for some feedback on how developer PCs are managed within environments that have a strict managed desktop policy (normally large corporations). For example, many corporate environments control the installation of software and the deployment of patches and virus updates through a centralised channel. This usually means also dictating the OS version and architecture (32 bit versus 64 bit) which will likely also mean standardised hardware configurations. I’m particularly interested in feedback from developers who work in this sort of environment but have a high degree of autonomy over their machines. This might mean choosing your own hardware vendor, OS type and version and perhaps how the machines are built and maintained. I have several specific questions: How do you satisfy the needs of security, governance etc whilst maintaining your autonomy? For example, how do you address concerns about keeping virus definitions and OS patches up to date? Do you have a process for gaining exemption from standard desktop builds and if so, what do you need to demonstrate in order to get this? How have you justified this need to the decision makers? Essentially, what is the benefit to your role as a developer by having this degree of autonomy? Thanks very much everyone. Update: There's a great post from Jean-Paul Boodhoo which addresses the developer tool component of the quesiton here: http://blog.jpboodhoo.com/TheFallacyOfTheStandardizedDeveloperMachineimage.aspx

  Read the article

• MacBook Pro with OSX 10.6.3 (Snow Leopard) Wi-Fi network connection breaks after few minutes

  - by Yanick Landry

  I have a MacBook Pro with OSX 10.6.3 (Snow Leopard). After connecting on a Wi-Fi network, the connection "breaks" after a few minutes. What I mean by "breaking" is that all requests, whether it is loading a web page, connecting to a share folder, connecting to my local router at 192.168.0.1, or pinging anything doesn't get through (time out). When in a "break" situation, I can see in the Network Settings panel that I still have an active IP, which I can successfully ping. I have this problem at home with a router D-Link DI-624 and at work with a D-Link WBR-2310, all with updated firmwares. I thought DHCP was the issue. So I tried assigning a fixed IP address (192.168.0.166). It successfully connects, but after a few minutes, the connection still breaks. The solution I'm currently using is that I disable the AirPort (on the Network icon menu in the top bar), wait a few seconds then re-enable it. It then quickly works, but the connection still breaks after a few minutes. I tried Googling my problem but I think I can't find any good keywords ! It's my first question here, so sorry if I don't respect some rules.

  Read the article

• Which steps are required to avoid my server being considered as spam sender?

  - by Cyril N.

  I'm looking to set up a webmail server that will be used by a lots of users that will receive and send emails. They will also have the possibility to forward emails they receive. I'd like to know which steps are recommanded/required to indicate to others Mail services (GMail, Outlook, etc) that my server is not used as a spam sender (disclaimer : IT's NOT ! :p) but a legitimate one. I know I have to define a SPF TXT records for example, but what others steps would you recommend me to do ? For example, is there a formula like having a proportional number of servers based on the amount of email sent (for having a different IP address) ? (something like sending a maximum of 1M emails / per IP / per day ?) Something else I'm missing ? I tried to search online, but I mostly find how to avoid emails sent with scripts (like PHP) being put in the SPAM folder. I'm looking for a server/dns configuration side. Thanks a lot for your help/tips, I appreciate !

  Read the article

• Ubuntu - wireless connection works great but wired is totally dead

  - by Dan

  I am running Ubuntu 10.04 on my Acer Aspire One netbook. The wireless connection works great, but the wired is totally dead. When I plug the Ethernet wire, the little led next to the port doesn't blink. If I do ifconfig, this is the output: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1659 errors:0 dropped:0 overruns:0 frame:0 TX packets:1659 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:132304 (132.3 KB) TX bytes:132304 (132.3 KB) wlan0 Link encap:Ethernet HWaddr 18:f4:6a:65:48:1f inet addr:192.168.1.7 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::1af4:6aff:fe65:481f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:94823 errors:0 dropped:0 overruns:0 frame:0 TX packets:81390 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:93028474 (93.0 MB) TX bytes:18002558 (18.0 MB) There is no eth0. Is that normal? In the "Network Connections" GUI there is an entry "Wired connection 1", its "MAC address" field is blank. How can I make the wired connection work?

  Read the article

• bond0:0 + define virtual IP

  - by yael

  hi all in my linux server I have the follwoing: Linux Version - RedHat-Linux- 5.3.0.0 (this linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it posible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

  Read the article

• bond0:0 + define virtual IP

  - by yael

  hi all in my linux server I have the follwoing: Linux Version - RedHat-Linux- 5.3.0.0 (this linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it posible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

  Read the article

• Print from Linux to Windows networked printer

  - by wonkothenoob

  I want to print from a Debian (Lenny) workstation to a Windows networked printer. I'm not even sure what type of Windows network this is. Our tech-support is friendly but doesn't want to get involved with supporting Linux. I need to use it for a variety of reasons and am completely stumped because I know nothing about Windows networking. They gave me URI smb://msprint.ourorg.edu as the "address" of the printer and further confirmed that the domain is "OURORG" and the share is "PHYS-PRI". I've installed CUPS and made sure that it's running as a daemon, I've clicked on the system-config-printer[1] icon, selected the printer as a Windows printer shared via SAMBA and entered the above URI. Attempting to print a testpage just sees it sit in the queue. I attempted to see if I could access the share using two other methods. Method 1. First I tried the "smbclient" from the CLI: $ smbclient -L //msprint.ourorg.edu -U user23 timeout connecting to 192.168.44.3:445 timeout connecting to 192.168.44.3:139 Connection to msprint.ourorg.edu failed (Error NT_STATUS_ACCESS_DENIED) Method 2. I tried to use the GUI tool Smb4K. This shows me four other toplevel (I'm assuming they're domains?) groupings one of which is the one which our IT department supplied to me. Clicking them shows a bunch of other machines with (what I assume are NetBIOS names?) including my own. I see all sorts of other networked printers belonging to other departments but none within mine. Certainly not the PHYS-PRI one suggested to me by the IT folks. I realize that I'm probably using the wrong terminology for the windows network, but can anyone help me with this? What steps should I be taking in debugging this? Do I need to actually run my machine as a SAMBA server to authenticate to the printer or should I just be able to communicate using CUPS? It's a GUI to CUPS configuration http://cyberelk.net/tim/software/system-config-printer/

  Read the article

• Remote network traffic not passing through VPN

  - by John Virgolino

  We have the following topology: LAN A LAN B LAN C 10.14.0.0/16 <-VPN-> 10.18.0.0/16 --- SONICWALL <-VPN-> M0N0WALL --- 10.32.0.0/16 Traffic between LAN A and LAN B works perfectly. Traffic between LAN C and LAN B works perfectly. Traffic between LAN A and LAN C, not so much. LAN A's gateway has a route to LAN C that points to the Sonicwall. The Sonicwall has a route to LAN A pointing to the VPN gateway connecting LAN B to LAN A. Tracing packets on the Sonicwall shows the LAN C destined traffic to arrive on the Sonicwall, but it does not forward the traffic, it dies there. Traffic from LAN B gets forwarded. Tracing packets on the Sonicwall while sending traffic from LAN C destined for LAN A shows nothing. This tells me that the M0N0WALL is not forwarding traffic for the 10.14.0.0 network and the Sonicwall is not forwarding from 10.14.0.0. The SA on the Sonicwall terminates on the WAN ZONE and is defined to use an address group that incorporates both the 10.14.0.0 and 10.18.0.0 networks. The M0N0WALL is configured for the 10.18.0.0 network and I have tried with both a static route to 10.14.0.0 and without on the M0N0WALL. I tried manually adding the 10.14.0.0 network to the SA on the M0N0WALL, but that really aggravated it and the SA never came up, so I reverted. I have checked all the firewall rules to make sure nothing is blocked. All of the Sonicwall auto-added rules look right. Specs: Sonicwall TZ200, Enhanced OS M0N0WALL v1.32 I'm at a loss at this point. Any help would be appreciated.

  Read the article

• Good HTTP Monitoring tools

  - by ffffff

  I look for HTTP to work with a Linux system server monitor tool every protocol. I know, and will not there be it in whom or a freeware? When, for example, I dump 80/tcp with a packet monitor to be concrete # tethereal -i ppp0 port 80 -x Capturing on ppp0 1244206390.030474 219.111.xx.xx -> 74.125.xx.xx HTTP GET /search?output=js&num=0&dt=1244206414703&client=pub-3031568651010206&q=Cagliari%20Flight&ad=n3&ie=utf8&oe=utf8&channel=0091594208&adtest=off HTTP/1.1 0000 00 04 02 00 00 00 00 00 00 00 00 00 00 00 08 00 ................ 0010 45 00 01 e5 ee 82 40 00 40 06 d2 b5 db 6f 02 5b E.....@[email protected].[ 0020 4a 7d 4f 93 d4 29 00 50 3e df 4c 63 4b 6b 42 e0 J}O..).P>.LcKkB Such output is provided, but there is too much unnecessary information such as an SYN packet or a header. What I want The IP address of the client and sending out character string(Get; the contents of the POST) Among the output character string of the server only as for the HTML (Content-Type:) I am what is chisel) of a thing of text/html. I can set a filter and am the best if only information wanting can accumulate in the log.

  Read the article

• How to handle OpenVPN client as a service, when the laptop is physically on the network already?

  - by James

  The Setup I've gotten OpenVPN working on our Windows XP laptops. Users are limited, so I went ahead and set OpenVPN client to run as a service, which is great anyway because that means they are on the VPN before logging in, so login scripts work, plus we can do remote support even if the user can not log in (such as connecting via VNC or resetting passwords). It is also configured to send all traffic over the tunnel, so when, for example, they browse the internet it is just like browsing from our corporate network. The Qestion(s) So, I'm wondering how does the OpenVPN client act when the computer is already physically on the same network as the OpenVPN server? Right now, the client is configured to connect the the public dns name which will resolve to the public ip address which will NOT get reflected back to the OpenVPN server, so it is affectively blocked from connecting to the OpenVPN server while on the network. Is that a good thing? Or will it constantly try to connect, using up system resources and network resources? We will likely have hundreds of laptops regularly on the physical network with this, so it could contribute to a lot of unnecessary network chatter. Alternatively Would it be better to have the firewall reflect the port back to the OpenVPN server and let it connect? Or have our internal dns resolve the name to the private ip and allow them to connect directly? Would traffic then go over the vpn connection (which I do not want, when already on the physical network)? Or is it possible to tell it to ignore the connection when the client and server are already on the same network? TLDR What's a sane way of handling OpenVPN client running as an always-on service when the client and server will often be on the same network?

  Read the article

• Exchange - inbound email only works from some servers

  - by Kryptonite

  I am having a problem where inbound mail from outside only works when sent from certain hosts. For example, when I send myself an email from my personal gmail account all is well, as the logs show: 2012-09-05 18:14:16 209.85.223.175 mail-ie0-f175.google.com SMTPSVC1 MAILSVR 192.168.1.79 0 EHLO 250 - - 2012-09-05 18:14:16 209.85.223.175 mail-ie0-f175.google.com SMTPSVC1 MAILSVR 192.168.1.79 0 STARTTLS 220 - - 2012-09-05 18:14:16 209.85.223.175 mail-ie0-f175.google.com SMTPSVC1 MAILSVR 192.168.1.79 0 STARTTLS 220 - - 2012-09-05 18:14:16 209.85.223.175 mail-ie0-f175.google.com SMTPSVC1 MAILSVR 192.168.1.79 0 EHLO 250 - - 2012-09-05 18:14:16 209.85.223.175 mail-ie0-f175.google.com SMTPSVC1 MAILSVR 192.168.1.79 0 MAIL 250 - - 2012-09-05 18:14:16 209.85.223.175 mail-ie0-f175.google.com SMTPSVC1 MAILSVR 192.168.1.79 0 RCPT 250 - - 2012-09-05 18:14:48 209.85.223.175 mail-ie0-f175.google.com SMTPSVC1 MAILSVR 192.168.1.79 0 QUIT 240 - - However, if I sent from my personal Yahoo account, I get this response: Sorry, we were unable to deliver your message to the following address. <[email protected]>: Remote host said: 530 5.7.0 Must issue a STARTTLS command first [MAIL_FROM] (NB: Nothing appeared in the smtp log for this message.) Any suggestions where to start looking? EDIT ---- I don't know if it matters, but the certificate I am using for TLS is self signed.

  Read the article

• IIS6 site using integrated authentication (NTLM) fails when accessed with Win7 / IE8

  - by Ciove

  Hi, I'm having pretty similar problems as described in case 139099, but the fix there doesn't seem to work for me. Here's the details: Server: Win2003Srv R2 SP2 (stadalone, not a member of a domain). IIS6, TCP/443 (https). Anonymous access disabled. Integrated Windows authentication enabled. Local useraccouts Each useraccount has own virtual folder with change access and read access to site root. The 'adsutil NTAuthenticationProviders "NTLM"' -thing set to site root and useraccount's virtual folder. Client: Win7 Enterprise Member of a AD-Domain IE8 Allows three login attepts then fails. Using [webservername][username] in the logon window (Windows security) Logon using other browsers (Chrome and Firefox) works OK. The Web services log shows one 401.2 and two 401.1 events. The Security Event log shows two events, first is Fauilure Audit (680), The second event is Fauilure Audit (529) with these details: Logon Failure: Reason: Unknown user name or bad password User Name: [username] Domain: [webservername] Logon Type: 3 Logon Process: NtLmSsp Authentication Package: NTLM Workstation Name: [MyWorkstation] Caller User Name: - Caller Domain: - Caller Logon ID: - Caller Process ID: - Transited Services: - Source Network Address: [999.999.999.999] Source Port: 20089 Any ideas appreciated.

  Read the article

• XAMPP server giving 404 error when requested by ipv4 connection

  - by boyb

  This is in reference to a previous question that I asked and was answered by womble. http://serverfault.com/a/406280/127729 So, now we have the real DNS records, we can do some diagnosis. dig for both A and AAAA on akosiboybastos.broker.freenet6.net gives a valid response, with an appropriate address. Good. dig for both A and AAAA on bastosforum.strangled.net gives the same responses (with a CNAME response thrown in). Also good. This means that the problem is not DNS-related, as those records are in order. wget -6 bastosforum.strangled.net/ gives a 200 OK response. wget -4 bastosforum.strangled.net/ gives a 404 Not Found response. This means that your webserver is misconfigured so that it's not serving the response you desire on IPv4. Given that the initial DNS problem asked in this question has been solved, I would recommend posting a new question with relevant webserver-related configuration, if you can't determine the configuration error yourself. I am using XAMPP(latest version) running phpbb3.0.10 via ipv6 tunnel from freenet6 and my domain is akosiboybastos.broker.freenet6.com, nothing fancy with the installation just out of the box install(with a few cosmetic mod). Both ipv4 and ipv6 traffic can connect using that url, but when I try to put a CNAME record on my test domain which is bastosforum.strangled.net pointing it to akosiboybastos.broker.freenet6.com only ipv6 can connect. As suggested by womble, this is a misconfigured webserver. To be honest I don't know where to start checking on the server as it is fully working if you use the domain given by freenet6 (akosiboybastos.broker.freenet6.com), any info on how to go about this server issue is welcome as i'm really a noob when it comes to computers. regards boyb

  Read the article

• Mapped network drive missing from My Computer and Explorer

  - by matt wilkie

  On a Windows XP Pro SP3 machine one network drive refuses to show up in My Computer or Explorer. The missing drive letter is G:, if that matters. Other mappings work fine. Other profiles one the same machine have no problem mapping G:. I can access the G: just fine typing it into the address bar or in CMD shell. I've used TweakUI to toggle hide/show G: with no difference. TweakUI says G: should be visible. I've logged off,on between toggles to make sure the settings are taking effect. I've looked at reg key [HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer] and made sure it's zero'd. [insert ref link here] We've limped along with this broken setup for some time, just working around it, but some applications do not allow typing in a path when choosing a place to save files and it's reached the point where it's intolerable. So, anyone have any idea why XP won't show this drive letter? or how to fix it?

  Read the article

• Can Haproxy deny a request by IP if its stick-table is full?

  - by bantic

  In my haproxy configs I'm setting a stick-table of size 5 that stores every incoming IP address (for 1 minute), and it is set as nopurge so new entries won't get stored in the table. What I'd like to have happen is that they would get denied, but that isn't happening. The stick-table line is: stick-table type ip size 5 expire 1m nopurge store gpc0 And the whole configs are: global maxconn 30000 ulimit-n 65536 log 127.0.0.1 local0 log 127.0.0.1 local1 debug stats socket /var/run/haproxy.stat mode 600 level operator defaults mode http timeout connect 5000ms timeout client 50000ms timeout server 50000ms backend fragile_backend tcp-request content track-sc2 src stick-table type ip size 5 expire 1m nopurge store gpc0 server fragile_backend1 A.B.C.D:80 frontend http_proxy bind *:80 mode http option forwardfor default_backend fragile_backend I have confirmed (connecting to haproxy's stats using socat readline /var/run/haproxy.stat) that the stick-table fills up with 5 IP addresses, but then every request after that from a new IP just goes straight through -- it isn't added to the stick-table, nothing is removed from the stick-table, and the request is not denied. What I'd like to do is deny the request if the stick-table is full. Is this possible? I'm using haproxy 1.5.

  Read the article

• STOP 0x7b booting from iSCSI

  - by Michael

  Hi, I've a Windows 2008 SBS running. It boots of iSCSI. That setup worked for months until yesterday. I intended to reboot and gained a: STOP 0x0000007b INACCESSIBLE_BOOT_DEVICE and no idea why. My setup hasn't changed. No new controller, no new or changed iSCSI targets, no new Network Card or IP address changes. I had all Windows Updates on it. Last known good: same STOP. Allow unsigned drivers: same STOP. Safe mode (all variants): same STOP. Mount target from a client: works. Filesystem check fine. I booted of the SBS DVD but in computer repair options my target doesn't appear. When i choose setup the target appears. So, how can i diagnose what's going wrong? Any helpful tools? Any hints? Thanks in advance Michael

  Read the article

• Single Sign On 802.1x Wireless - saying “Connecting to <SSID>”, hangs for 10 seconds, fails with “Unable to connect to <SSID>, Logging on…”.

  - by Phaedrus

  We are implementing WiFi on Windows 7 machines in our corporate environment. Machines should be able to log into the domain by WiFi as the Machine (Pre-Logon), and as the User (Post-Logon). We have everything working correctly except for 2 things: 1) Sometimes the login scripts don't run 2) The user VLAN is sometimes different than the machine vlan, and no DHCP renew occurs after user logon. I am clear that both these problems should be fixable by using the "Single Sign On" Option under the 802.1x Wireless Vista GPO, and setting the wireless to connect immediately before user logon and also by enabling "This network uses different VLAN for authentication with machine and user credentials" If I enable these GPO settings in a lab, the computer does authenticate & gets WIFI before the user logs on, so when the login box is displayed, it says “Windows will try to connect to ”, even though it is already connected (which should be ok?). Enter the user credentials and it goes to a screen saying “Connecting to ”, hangs for 10 seconds, fails with “Unable to connect to , Logging on…”. Desktop fires up and then the user re-authenticates with no problem as himself instead of the machine, but by that point, we defeat the point of the WiFi SSO “before user logon”. Also by that point, no DHCP renew seems to occur, and the user is still stuck with the wrong IP address for the new VLAN. When the “Connecting to ” screen comes up, there’s no indication on the AP or the Radius server that anything whatsoever is happening after credentials are entered until after the domain logon. Also with this policy enabled, sometimes windows hangs on a black screen indefinitely until I disable the Wireless NIC, so something is knackered for sure. What have I missed? Suggestions are much appreciated... /P

  Read the article

• Per-mailbox IMAP settings in Exchange 2003 apply successfully but revert to server default

  - by erictheavg

  The title says most of it. I have a Spiceworks mailbox that connects to our Exchange Server 2003 box via IMAP for receiving help desk issues. But for complicated reasons, I want it to receive those emails in text-only format. So, I discovered that you can just go to: Exchange System Manager Administrative Groups First Administrative Group First Storage Group Mailbox Store Mailboxes Right-click the mailbox, Configure Exchange Features Edit the properties for IMAP Set that mailbox to only receive message bodies as plain text. I click OK, then Next, it reports success, and I assume I'm done. But then when I go right back to where I was, I see that "Use protocol defaults" is still checked. Anyone have a clue why this would be? Some other details: I'm logged in as Administrator when I do this. I can't change this setting for the entire IMAP virtual server because some regular users use it. I only have one IP address to play with, which means I can't create another IMAP virtual server. Any suggestions or ideas are greatly appreciated!

  Read the article

< Previous Page | 662 663 664 665 666 667 668 669 670 671 672 673  | Next Page >