Search Results

Search found 2697 results on 108 pages for 'tan kah ping'.

Page 68/108 | < Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >

• Can't add printer on Windows XP

  - by SuperFurryToad

  I've added a HP 4250 printer to about half a dozen Windows XP PCs in our office without any problems whatsoever, but for some reason I haven't been able to add it to one particular PC today. I go through the Add Printer wizard to add a local printer attached to the PC, enter the new port number as a Standard TCP/IP Port, install the driver. At the end of the wizard I get the following error message: Full error message: "windows cannot connect to the printer. either the printer name was typed incorrectly, or the specified printer has lost its connection to the server." This doesn't make any sense as I am able to ping the printer from the PC. The print spooler is running, and any firewall software on the local PC is switched off.

  Read the article

• Virus blocking incoming connections ?

  - by Benoît

  Hello, on my windows 2003 server, all incoming connections are dropped. I can see them getting in using Wireshark, but even a single ping from another computer fails. All locally initiated connection work fine (i'm asking from the server). This server is the DC/DHCP/DNS/File server, so computer clients are in the dark. I've run varius antivirus and removal tools without any luck. The Windows Firewall is disabled. I'm wild-guessing at some virus/worm. How can i check why these incoming ICMP/TCP SYN/etc are dropped ? Anyone has any knowledge about such situations ? Thanks.

  Read the article

• Unable to connect to another computer from the Task Scheduler on Windows 7

  - by Clem

  I am getting the following error when trying to connect to another computer from the Task Scheduler on Windows 7: "The remote computer was not found." The computer that I am trying to connect to is definitely on the network as I can ping it and browse its shared folders in Windows Explorer. Note that I get the same error message when trying to perform the same operation from Performance Monitor. This suggests that I need to something to enable remote connection to the Task Scheduler. I am not very experienced with Windows administration and I am not sure where to look. To give a bit more context, I want to use the Task Scheduler to automatically start Perf Mon on a few machines at my company. I'd like to setup the Task Scheduler remotely. Does anyone know what I need to do?

  Read the article

• What are the things to look out for when adding other domain user to your IIS?

  - by Jack

  I have a Windows Server 2008 R2 called Jack11 that joined a domain called Watson.org. It has IIS 7 installed. From my understanding, we need to add the following into the web.config file <system.web> <identity impersonate="true" /> </system.web> Also, we need to ensure that the server Jack11 can ping to the domain Watson.org. What other setting do we need to setup in order for a user of domain Watson.org (e.g. the user Watson\User1 to access the application in the Server IIS? This is because currently, there is a problem as follows: Exception Details: System.Data.SqlClient.SqlException: Login failed for user 'WATSON\User1'. The error message was displayed when the user User1 wish to access one of the web application in server Jack11 IIS and that web application also do some retrieval of records from the database, which is installed in SQL Server 2008 Enterprise located in the same server Jack11.

  Read the article

• VMWare Hypervisor vSphere 5 - VM static ip from VLAN NAT

  - by Ian Livingstone

  I have a VMWare vSphere 5 Hypervisor server that has a static ip address assigned to it by VLAN that is configured to perform NAT. The static IP is assigned to the bare metal server via the NIC's mac address. I want to setup a guest machine to also have a static ip address, how can I go about having this setup? I have assigned a IP for the guest's MAC Address but it doesn't seem to be working as when I ping the ip address it does not respond. The guest is running ubuntu 10.04 server edition. I am trying to assign it a static public ip address. Any help would be greatly appreciated.

  Read the article

• NLB RPC server is unavailable on the specified computer

  - by Robin Weston

  Hi guys, Firstly, I'll admit that my networking knowledge is limited so as people request more information I'll update this question accordingly. I am trying to create a NLB Cluster across 2 Windows Server 2008 Web Servers. Neither of the machines are members of a domain, and both have 2 NICs (one for processing external web traffic, and one for communicating internally). I have installed NLB on both machines, and have created a cluster on Host A and added itself to it. However, when I try and add Host B (using the address from the external NIC) I get the following error : "The RPC server is unavailable on the specified computer". On Host B I can see that the RPC service is running fine. I can also ping and RDP from Host A to Host B with no problems either. I have disabled the windows firewall on both machines but that had no effect

  Read the article

• Unable to connect my computer from LAN (http, smb) in UBUNTU 10.04

  - by Abdul Majeed

  I installed ubuntu 10.04, Apache, PHP, mysql, smb. Everything work fine in locally in my IP. When i trying to access my computer from LAN (other computer), it shows unable to connect. when i ping my IP from remote computer, its pinging OK. I can access internet, and all other systems (http, smb). But the problem is no one can't access my computer remotely in my LAN network. My ip is 192.168.85.105 and i want access(Appaceh,SMB) from 192.168.85.10. Is there any proxy firewall settings? I had tried following commands.. sudo iptables -F or sudo iptables-restore [logout require] If it does not work then try to disable net-filter sudo ufw --disable Please give me the solution.

  Read the article

• Vista laptop won't connect to airport extreme

  - by Hutch

  Our previous router died, and to replace it I procured an apple airport extreme. My mac, my wrt54gs (with ddwrt acting as a bridge) and a linux machine have had no problem connecting to the wireless. None of the wired clients are having a problem obviously. The problem is one of my roommates can not connect. That's not strictly true. He can connect to the network, and will, infact, get a dhcp lease. However he cannot get any packets out. Can't ping the router, can't access any web sites, nothing. However he's fine if we switch to an unsecured network. Which is obviously not acceptable. The airport only allows for 'wpa/wpa2 personal' and 'wpa2 personal' (and of course the enterprise versions there of) I keep reading about this problem in multiple spots on the web, but never see any actual answers... Anyway the laptop: hp/compaq cq50-215nr vista home premium wireess card: atheros 5007 airport is simultaneos dualband II

  Read the article

• Why can't I access a particular website even though the server appears to be available

  - by 50ndr33

  I can't access http://www.lynda.com/ with any of my browsers on my home network. By checking http://www.downforeveryoneorjustme.com/, I can see that the server is up and I can access it via a proxy like TOR. This screen appears immediately after I type the page in It doesn't even try to load the page, it seems. Though when I ping the server I get this: I tried to do ipconfig /flushdns. But it didn't help either. Anyone know how to fix this?

  Read the article

• Can Remote Desktop be set up to use IPv6?

  - by Garrett

  I have both a Windows 7 Ultimate and a Windows XP Professional machine set up on my home network. I would like to be able to access them from school. Port forwarding is not currently an option (long story). Is there a way to set it so that I can RDP (yes it has to be RDP not something like TeamViewer or LogMeIn) over IPv6, possibly using Teredo? I have tried but I can't seem to get it working. Also I cannot ping these machines' IPv6 addresses. How can I get this set up?

  Read the article

• Public DNS Server fails on Windows Amazon EC2

  - by Adroidist

  I have started a new Windows server instance on Amazon EC2. The security group has the following rules: Ports Protocol Source 22 tcp 0.0.0.0/0 80 tcp 0.0.0.0/0 443 tcp 0.0.0.0/0 3389 tcp 0.0.0.0/0 53 udp 0.0.0.0/0 -1 icmp 0.0.0.0/0 I am able to ping the public DNS server of the machine and i can connect to it using Windows Remote Desktop connection. However, when i put in my web browser the public DNS server, it fails to connect. Morever, I used filezilla and putty (and in both I loaded the private key .pem) but i receive connection timed out. I disabled the firewall on both my pc and the instance (which I entered using Remote desktop connection). Can you please tell me what I am missing?

  Read the article

• My computer is listed twice in the Network view; network shares are not accessible

  - by romkyns

  I have a couple of network shares set up on my Win7 machine. They've been in constant use, from that same machine on which they're set up. One morning they just randomly stopped working: When I went looking for what was wrong, I noticed that I also had my PC listed twice in the Network view in Explorer: "Sirius" is the name of the PC on which these screenshots were taken. I may have installed some windows updates around the time this happened. I have since tried rebooting and installing all the latest updates, to no avail. I've also removed the share in question and re-added it, making sure I give all rights to everyone. I'm an administrator on this machine, but I can't access the administrative shares (\\SIRIUS\c$) either, with the same message. I can access \\localhost\AcronisImages and \\localhost\c$, and I can ping sirius. Any ideas?

  Read the article

• Solaris 11.1 smb share pam.conf

  - by websta

  I would like to enable an SMB share on Solaris 11.1 x64 My steps: pkg install service/filesystem/smb svcadm enable -r smb/server echo "other password required pam_smb_passwd.so.1 nowarn" >> /etc/pam.conf useradd public smbadm enable-user public zfs set share=name=fs1,path=/rpool/fs1,prot=smb rpool/fs1 zfs set sharesmb=on rpool/fs1 passwd -r files public Step 8 failes: It is not possible to enter a password, output is: solaris passwd -r files public Please try again Please try again Permission denied If I uncomment the new line in pam.conf, it is possible to change the password. Nevertheless, it is not possible to access the share from Windows 7. The Solaris machine is reachable with ping. Access with another SMB enabled user is denied too.

  Read the article

• Can't connect to domain computers until reboot

  - by thealliedhacker

  I have a domain with about 300 Windows 7 and XP machines, with the domain controllers running Server 2003. Sometimes, I lose the ability to communicate/authenticate with some of the machines until I reboot my computer. This also happens from other computers and regardless of user account and operating system. In other words, say I'm on ComputerA, and I can't connect to ComputerX. I can go to ComputerB and connect to ComputerX, but ComputerB may not be able to connect to ComputerY. If you reboot ComputerA, then it will be able to connect to ComputerX again. Here are some messages from various utilities: sc: [SC] OpenSCManager FAILED 1722: The RPC server is unavailable. mmc (compmgmt.msc): Computer (computer name) cannot be managed. The network path was not found. explorer (\\computer): Windows cannot access \\(computer name). ping: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss) / Average = 1ms

  Read the article

• Disable IPv6 on Loopback address (Localhost, Computer name, ...)

  - by Greg Bray

  We tried installing a 3rd party software product on a new Windows 2008 R2 server and found that everything works except for accessing local services through loopback addresses such as localhost or the computer name (ex: VPS-Web which resolves to localhost). We are not using IPv6 and would like to disable it until the software is compatible. I tried using these instructions for disabling IPv6 on Windows 2008 R2 but it did not disable the protocol for localhost. Pinging localhost or VPS-Web will still return ::1: instead of 127.0.0.1. I can use ping localhost -4 to get the correct address, but IPv6 takes precedent over IPv4 so the 3rd party software only gets the IPv6 address.

  Read the article

• set tap0 using virt-manager for bridged wireless

  - by DaveO

  After 3 days I finally have kvm guests working on the network via wireless (link below - thanks!): My network is 192.168.1.0/24 on the host: sudo sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward" sudo tunctl -t tap0 sudo ip link set tap0 up sudo ip addr add 192.168.1.25/24 dev tap0 sudo route add -host 192.168.1.30 dev tap0 sudo parprouted wlan0 tap0 on the guest: auto eth0 iface eth0 inet static address 192.168.1.30 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.25 and start the guest: sudo kvm /path/to/guest.img -net nic,macaddr=DE:AD:BE:EF:90:26 -net tap,ifname=tap0,script=no This works great and I can ping the local network and the internet back and forth between the guest. But how do I add these settings to the guest's xml config so I can start the guest via virt-manager with the same nic settings? ref: http://www.linuxquestions.org/questions/debian-26/kvm-wireless-bridge-network-691953/

  Read the article

• Remote location looses connectivity

  - by user24559

  I have a remote location that has constant internet access using DSL. The remote location only has three Linksys cameras that use the internet access with a router. There is no computer on the network. The router is configured to use the DYN.org service to keep the IP address updated if the internet provider assigns a new ip address. The problem I am having is the router after a period of time stops responding to incoming ping requests and the cameras are shown offline. However, if I keep one of the cameras constantly streaming data then the connection to all the cameras works just fine all the time. How can I keep the router from appearing to be sleeping and not responding to incoming requests? The router is the Linksys WRT300N.

  Read the article

• Accessing SQL with the PC name not the IP

  - by Cornelius

  I'm trying to connect to a SQL instance (default instance) on a machine. When using the IP of the machine it connects to the machine. Using the name of the machine on that machine you are able to establish a connection to the SQL instance but using the machine name on another PC the connection cannot be established. And gives the error A network-related or instance-specific error occurred while establishing a connection to SQL Server. ... (Microsoft Server, Error: 10060) The machine that I am trying to establish the connection from can ping the machine with the SQL instance both on the IP and on the name. Why would this be and how can I fix it? Edit: pinging the name does resolve the correct IP. Pinging the FQDN also works correctly.

  Read the article

• Network access to VM only from host ...

  - by Jamie

  I'm trying to do some testing of Ubuntu 10.04 Beta 2 Server in a VMWare environment. The host is XP, and the VM software is VMPlayer. Problem is, I want to be able to see the VM from the network, not just from the host. I can SSH into the VM from the host, but from any other machine on the network I can't even get the VM to respond to a ping. Going the other way (from the VM out) isn't a problem at all. The VM software did an 'easy installer' so I'm not really sure what was going on with the networking. Suggestions?

  Read the article

• Connected to internet but can't browse after trying to remove Covenant Eyes

  - by Joanna

  I recently got a MacBook Pro. It connects to ethernet\wifi and has internet but when I open Safari or Firefox, nothing happens. I get a timeout for all websites. I had Covenant Eyes on my Mac before and tried to remove it. My friends who work with computers have tried everything (ping, nslookup etc). Network diagnostics show no problems I can see I'm connected through ifconfig because I get an IP. I also get a response pinging www.google.gr. There are no proxies set in my Network preferences. Any ideas?

  Read the article

• Juniper J4350 out of order

  - by Benjamin Baron

  I have got two (2) Juniper routers J4350 that are out of order : All the interfaces are down (leds on the interfaces don't ligthen, ping dosen't respond) No output on the console port (even when booting) I've tried to reset the router (holding the RESET CONFIG button on the front panel during 15 seconds) and nothing happened, even while booting the device I've opened the router to check the fans. I've removed some dust and nothing has changed. I wanted to precise that the leds on the front panel are all on: The POWER led is green The STATUS led is red The ALARM led is on and is orange The HA (High Availablity) is on and orange as well I have found nothing on the Internet to solve this problem... Thank you for helping me :)

  Read the article

• set tap0 using virt-manager for bridged wireless

  - by DaveO

  After 3 days I finally have kvm guests working on the network via wireless (link below - thanks!): My network is 192.168.1.0/24 on the host: sudo sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward" sudo tunctl -t tap0 sudo ip link set tap0 up sudo ip addr add 192.168.1.25/24 dev tap0 sudo route add -host 192.168.1.30 dev tap0 sudo parprouted wlan0 tap0 on the guest: auto eth0 iface eth0 inet static address 192.168.1.30 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.25 and start the guest: sudo kvm /path/to/guest.img -net nic,macaddr=DE:AD:BE:EF:90:26 -net tap,ifname=tap0,script=no This works great and I can ping the local network and the internet back and forth between the guest. But how do I add these settings to the guest's xml config so I can start the guest via virt-manager with the same nic settings? ref: http://www.linuxquestions.org/questions/debian-26/kvm-wireless-bridge-network-691953/

  Read the article

• cant access site intermittent as i get site not available

  - by user61438

  i have a news site i check stuff for regularly.. once in a while i cant access it completely from my 5 different browsers and even from the command line, nslookup cant resolve, ping and tracert fails.. all not being able to resolve site name..the problem is specific to this.. i am told by the site support person that problem is that its cache on my machine or on ISP and I say thats not true because this site I access it 1-2-3 times a week from one browser only.. i only fire up the other ones in times of trouble..and when i have the problem even if i try on my secondary machines i still get the same problems.. when problem goes away all works well.... question is whats causing the intermittent dns/http problems... i don't believe this is something to do with my machine because probe disappears without me having done anything at all.

  Read the article

• Plesk 9 VPS - Doesn't reply to NameServer requests (nslookup, etc)

  - by Ben

  Hi, I'm trying to troubleshoot a problem with a new VPS i'm setting up. The VPS is running Plesk 9 on a CentOS 5 system. Everything works fine, except it doesn't serve dns requests. If I try something like nslookup [somedomain.com] the.ser.ver.ip to test a DNS query, i get the following error ;; connection timed out; no servers could be reached I can't telnet to it on port 42 either.. I'm guessing something is blocking the requests.. firewall maybe? the plesk firewall module is installed and the nameservers entry is green. Any other way I can check what's blocking it on the server? Any help/tip greatly appreciated. Note: http works, i can telnet to the server on port 80 and i can also ping the server Thanks

  Read the article

• Why is my hosts file not working?

  - by elliot100

  I've been using the hosts file to for local website development, and it's recently stopped working. No entries other than localhost resolve. I've simplified to test, so it now contains only 127.0.0.1 localhost ::1 localhost 127.0.0.1 test.dev localhost responds to ping, test.dev does not. The file is called hosts with no extension It has no trailing spaces It's saved in C:\WINDOWS\System32\drivers\etc which matches the value of HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\DataBasePath Oddly, despite UAC being on, I can edit, delete and save the file without admin permissions No proxy is being used, PC is not connected to network for testing Stopping the DNS Client service seemed to resolve the issue for a few minutes, test.dev briefly resolved but doesn't any more. Only firewall is Windows' Machine has been restarted. Is there anything else I should try?

  Read the article

< Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >