Search Results

Search found 34556 results on 1383 pages for 'setting as default'.

Page 69/1383 | < Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >

• help setting up an IPSEC vpn from my linux box

  - by robthewolf

  I have an office with a router and a remote server (Linux - Ubuntu 10.10). Both locations need to connect to a data supplier through a VPN. The VPN is an IPSEC gateway. I was able to configure my Linksys rv42 router to create a VPN connection successfully and now I need to do the same for Linux server. I have been messing around with this for too long. First I tried OpenVPN, but that is SSL and not IPSEC. Then I tried Shrew. I think I have the settings correct but I haven't been able to create the connection. It maybe that I have to use something else like a direct IPSEC config or something like that. If someone knows of a way to turn the following settings that I have been given below into a working IPSEC VPN connection I would be very grateful. Here are the settings I was given that must be used to connect to my supplier: Local destination network: 192.168.4.0/24 Local destination hosts: 192.168.4.100 Remote destination network: 192.167.40.0/24 Remote destination hosts: 192.168.40.27 VPN peering point: xxx.xxx.xxx.xxx Then they have given me the following details: IPSEC/ISAKMP Phase 1 Parameters: Authentication method: pre shared secret Diffie Hellman group: group 2 Encryption Algorithm: 3DES Lifetime in seconds:28800 Phase 2 parameters: IPSEC security: ESP Encryption algortims: 3DES Authentication algorithms: MD5 lifetime in seconds: 28800 pfs: disabled Here are the settings from my attempt to use shrew: n:version:2 n:network-ike-port:500 n:network-mtu-size:1380 n:client-addr-auto:0 n:network-frag-size:540 n:network-dpd-enable:1 n:network-notify-enable:1 n:client-banner-enable:1 n:client-dns-used:1 b:auth-mutual-psk:YjJzN2QzdDhyN2EyZDNpNG42ZzQ= n:phase1-dhgroup:2 n:phase1-keylen:0 n:phase1-life-secs:28800 n:phase1-life-kbytes:0 n:vendor-chkpt-enable:0 n:phase2-keylen:0 n:phase2-pfsgroup:-1 n:phase2-life-secs:28800 n:phase2-life-kbytes:0 n:policy-nailed:0 n:policy-list-auto:1 n:client-dns-auto:1 n:network-natt-port:4500 n:network-natt-rate:15 s:client-dns-addr:0.0.0.0 s:client-dns-suffix: s:network-host:xxx.xxx.xxx.xxx s:client-auto-mode:pull s:client-iface:virtual s:client-ip-addr:192.168.4.0 s:client-ip-mask:255.255.255.0 s:network-natt-mode:enable s:network-frag-mode:disable s:auth-method:mutual-psk s:ident-client-type:address s:ident-client-data:192.168.4.0 s:ident-server-type:address s:ident-server-data:192.168.40.0 s:phase1-exchange:aggressive s:phase1-cipher:3des s:phase1-hash:md5 s:phase2-transform:3des s:phase2-hmac:md5 s:ipcomp-transform:disabled Finally here is the debug output from the shrew log: 10/12/22 17:22:18 ii : ipc client process thread begin ... 10/12/22 17:22:18 < A : peer config add message 10/12/22 17:22:18 DB : peer added ( obj count = 1 ) 10/12/22 17:22:18 ii : local address 217.xxx.xxx.xxx selected for peer 10/12/22 17:22:18 DB : tunnel added ( obj count = 1 ) 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : client config message 10/12/22 17:22:18 < A : local id '192.168.4.0' message 10/12/22 17:22:18 < A : remote id '192.168.40.0' message 10/12/22 17:22:18 < A : preshared key message 10/12/22 17:22:18 < A : peer tunnel enable message 10/12/22 17:22:18 DB : new phase1 ( ISAKMP initiator ) 10/12/22 17:22:18 DB : exchange type is aggressive 10/12/22 17:22:18 DB : 217.xxx.xxx.xxx:500 <- 206.xxx.xxx.xxx:500 10/12/22 17:22:18 DB : c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 DB : phase1 added ( obj count = 1 ) 10/12/22 17:22:18 : security association payload 10/12/22 17:22:18 : - proposal #1 payload 10/12/22 17:22:18 : -- transform #1 payload 10/12/22 17:22:18 : key exchange payload 10/12/22 17:22:18 : nonce payload 10/12/22 17:22:18 : identification payload 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v00 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v01 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v02 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v03 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( rfc ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports DPDv1 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SHREW SOFT compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is NETSCREEN compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SIDEWINDER compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is CISCO UNITY compatible 10/12/22 17:22:18 = : cookies c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 = : message 00000000 10/12/22 17:22:18 - : send IKE packet 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 ( 484 bytes ) 10/12/22 17:22:18 DB : phase1 resend event scheduled ( ref count = 2 ) 10/12/22 17:22:18 ii : opened tap device tap0 10/12/22 17:22:28 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:38 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:48 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:58 ii : resend limit exceeded for phase1 exchange 10/12/22 17:22:58 ii : phase1 removal before expire time 10/12/22 17:22:58 DB : phase1 deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : closed tap device tap0 10/12/22 17:22:58 DB : tunnel stats event canceled ( ref count = 1 ) 10/12/22 17:22:58 DB : removing tunnel config references 10/12/22 17:22:58 DB : removing tunnel phase2 references 10/12/22 17:22:58 DB : removing tunnel phase1 references 10/12/22 17:22:58 DB : tunnel deleted ( obj count = 0 ) 10/12/22 17:22:58 DB : removing all peer tunnel refrences 10/12/22 17:22:58 DB : peer deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : ipc client process thread exit ...

  Read the article

• setting up/installing/configuring nginx LEMP stack on fresh VPS server

  - by Grant Tailor

  I need some help in settingup/installing and configuring nginx LEMP stack on a fresh new VPS I have. The specs of the CentOS 5.7 VPS are 2GB DDR3 ECC RAM(4GB burst), 1 core 1.5Ghz(3Ghz burst) and 100GB RAID 10 storage, unmetered bandwidth @ 100Mpbs all for a whopping $25/month(unbeatable, yeah I know :) Anyways I have followed this LEMP (will also need MySQL and PHP) stack guide on linode http://library.linode.com/lemp-guides/centos-5 but basically what I want is to be able to host multiple website on this webserver after everything is setup. I am used to using DirectAdmin control panel on other server and want to have things setup so I can host multiple websites - mostly wordpress and drupal themes. Lets say 10 websites on this nginx web server. So can someone please help me on what I need to do to take "full" advantage of nginx power and performance, while been able to easily manage these multiple websites (wordpress and drupal themes)?

  Read the article

• Setting Up Git Repository on Remote Windows Server?

  - by Goober

  I have a windows server which I can access locally or remotely over the internet through remote desktop connection, etc. I want to set up a git repository (something similar to "trunk" in subversion), that can contain a series of repositories for multiple projects. Does anyone know how I go about doing this? I want to do it using a GUI if possible. I have followed this Git Bash Tutorial but it's very long winded and not exactly what I'm after. I'm using a Git client called MSYSGIT. Using this I just want to be able to set up remote repositories and start committing source code. Any help would be greatly appreciated!

  Read the article

• Error setting up Data Protection Manager 2010 Agents / Network "Unauthenticated" in network settings

  - by Bowsa

  I'm not sure if the two are connected but i suspect they are. Basically I'm tring to setup Data Protection Manager 2010 on a fresh install of Server 2008 R2 in a SBS 2003 domain. Everything went fine until trying to install agents across the network. Upon clicking add, i get the following error message: Unable to connect to the Active Directory Domain Services Database. Make sure that the DPM server is a member of a domain and that the controller is running. Also verify that there is network connectivity between the DPM server and the domain controller. ID: 7 As usual (worryingly) the MSDN support for 2010 products is nearly non existant, clicking the error ID simply gives a page not found error. So after 2 days of Googling and trying various fixes (DNS settings, adding permissions to AD objects, rejoining the domain and many more) I thought I'd ask here in the hope that someone out there may have had this issue before. Any help greatly appreciated! Some further info: Firewalls are disabled on the Server 2008, SBS, and client machines. Manually installing and adding the client in also fails, as the DPM server tries to contact the DC first. Edit: I tried creating a new protection group instead, and it gives a different error upon adding the machines: Following machines are not found in AD: COMPUTERNAME.COMPANYNAME.LOCAL Is there a certain directory structure it follows in AD?

  Read the article

• TFS2010 - Correctly setting up Host Header

  - by Keith Barrows

  We have a TFS2010 install on a Win2008R2 Server running IIS7. I've created a host header for TFS and want to use that instead of machineName:8080. I am getting weird behavior from it now. Every other time I log in I get: TF31002: Unable to connect to this Team Foundation Server: http://web2/tfs. Team Foundation Server Url: http://web2/tfs. Possible reasons for failure include: - The name, port number, or protocol for the Team Foundation Server is incorrect. - The Team Foundation Server is offline. - The password has expired or is incorrect. Technical information (for administrator): The request failed with HTTP status 404: Not Found. I force a reconnect and voila - there it is. Also, connecting to the web site rarely works but connecting via VS2010 works 50% of the time. What do i need to change to stabilize this?

  Read the article

• Setting up DNS in WHM/cPanel

  - by Jon Furmanski

  I don't understand what I'm doing wrong, but I'm sure this is a simple fix. I setup WHM/cPanel for the first time on my VPS and understand how DNS works for the most part (or so I thought). I created under the main domain name 2 nameservers (ns1.maindomain.com & ns2.maindomain.com). I have 2 IP address for my sever so each one points to a unique IP: ns1.maindomain.com => 198.x.x.204 ns2.maindomain.com => 198.x.x.205 I also set up reverse DNS with my hosting provider. When I put in my two nameservers under another domain (secondary domain), GoDaddy states that the nameservers are invalid. Any ideas on why this is or any configurations in cPanel that need to be made?

  Read the article

• setting up git on cygwin - openssl

  - by Pete Field

  I'm trying to get git running in cygwin on a windows 7 machine I have git unpacked and the directory git-1.7.1.1 when i run make install from within that directory, I get CC fast-import.o In file included from builtin.h:4, from fast-import.c:147: git-compat-util.h:136:19: iconv.h: No such file or directory git-compat-util.h:140:25: openssl/ssl.h: No such file or directory git-compat-util.h:141:25: openssl/err.h: No such file or directory In file included from builtin.h:6, from fast-import.c:147: cache.h:9:21: openssl/sha.h: No such file or directory In file included from fast-import.c:156: csum-file.h:10: error: parse error before "SHA_CTX" csum-file.h:10: warning: no semicolon at end of struct or union csum-file.h:15: error: 'crc32' redeclared as different kind of symbol /usr/include/zlib.h:1285: error: previous declaration of 'crc32' was here csum-file.h:15: error: 'crc32' redeclared as different kind of symbol /usr/include/zlib.h:1285: error: previous declaration of 'crc32' was here csum-file.h:17: error: parse error before '}' token fast-import.c: In function `store_object': fast-import.c:995: error: `SHA_CTX' undeclared (first use in this function) fast-import.c:995: error: (Each undeclared identifier is reported only once fast-import.c:995: error: for each function it appears in.) fast-import.c:995: error: parse error before "c" fast-import.c:1000: warning: implicit declaration of function `SHA1_Init' fast-import.c:1000: error: `c' undeclared (first use in this function) fast-import.c:1001: warning: implicit declaration of function `SHA1_Update' fast-import.c:1003: warning: implicit declaration of function `SHA1_Final' fast-import.c: At top level: fast-import.c:1118: error: parse error before "SHA_CTX" fast-import.c: In function `truncate_pack': fast-import.c:1120: error: `to' undeclared (first use in this function) fast-import.c:1126: error: dereferencing pointer to incomplete type fast-import.c:1127: error: dereferencing pointer to incomplete type fast-import.c:1128: error: dereferencing pointer to incomplete type fast-import.c:1128: error: `ctx' undeclared (first use in this function) fast-import.c: In function `stream_blob': fast-import.c:1140: error: `SHA_CTX' undeclared (first use in this function) fast-import.c:1140: error: parse error before "c" fast-import.c:1154: error: `pack_file_ctx' undeclared (first use in this functio n) fast-import.c:1154: error: dereferencing pointer to incomplete type fast-import.c:1160: error: `c' undeclared (first use in this function) make: *** [fast-import.o] Error 1 I'm guessing that most of these errors are due to the iconv.h and openssl files which apparently are missing, but I can't figure out how I'm supposed to install those (if I am), or if there is some other way to get around this.

  Read the article

• setting up delegate or smtp forwarding

  - by cotiso

  for work we have a remote dedicated server to run our webservice that also runs our email services, at home(comcast residential internet) i cannot send mail using the dedicated server's SMTP, comcast spits back a error saying i can only use their SMTP server for sending mail at work(comcast business internet) we can use our dedicated server for sending mail with no problem so i set up a box at work to forward smtp traffic, i'm new to all this networking stuff by the way i used delegate to forward smtp traffic, can someone point me in the right direction on how to use this program(delegate) to fix our issue the delegate command i used to test is : delegated -P25 SERVER="smtp://dedicated.server.com:25" PERMIT=":::" -v i also opened up port 25 on the router so it points to my boxes ip are there any other ways to fool comcast into thinking im using my works ip to send mail, my coworkers and i are unable to send mail from home for some time now thanks

  Read the article

• Which DNS settings are used when setting up your server

  - by Saif Bechan

  I have a server and want to run my own name server service. Now I have set it up already and it works not, but I do not know where the exact settings are stored. On my server I use Plesk. When I edit DNS settings there I think it is stored in named.conf. Named is installed on the server, and BIND. Now I also have a panel from my registrar. This is separate from my server. Both places I can add the normal MX,A,CNAME, etc records. Now where is the best way to place this settings. Currently I have the same records on both places, on the server and at the registrar panel. I am correct to just add all the records at the registrar panel, and remove everything from within PLESK, and just don't run DNS on my server, because it is already done in the registrar panel. Or should I add the records in both places.

  Read the article

• Setting font size of Closed Captions on iPhone using ffmpeg or mencoder

  - by forthrin

  Does anyone know how to either: Make ffmpeg set subtitle font size in the output video file Make mencoder produce an iPhone-compatible video file (with subtitles) I finally found out how to get Closed Captions video on iPhone, with mkv and srt files as source material. The secret was using the mov_text subtitle codec in ffmpeg (and turning on Closed Captions in the iPhone settings of course): ffmpeg -y -i in.mkv -i in.srt -map 0:0 -map 0:1 -map 1:0 -vcodec copy -acodec aac -ab 256k -scodec mov_text -strict -2 -metadata title="Title" -metadata:s:s:0 language=eng out.mp4 However, the font size appears very small on the iPhone, and I can't find out how to set it with ffmpeg (the iPhone has no option for this). I found out that mencoder has a -subfont-text-scale option, but I don't have a lot of experience with this program. The following, my best attempt so far, produces an output file which is not playable on the iPhone. sudo port install mplayer +mencoder_extras +osd mencoder in.mkv -sub in.srt -o out.mp4 -ovc copy -oac faac -faacopts br=256:mpeg=4:object=2 -channels 2 -srate 48000 -subfont-text-scale 10 -of lavf -lavfopts format=mp4 PS! As requested, here is the output from mencoder: 192 audio & 400 video codecs success: format: 0 data: 0x0 - 0xb64b9d2f libavformat version 54.6.101 (internal) libavformat file format detected. [matroska,webm @ 0x1015c9a50]Unknown entry 0x80 [lavf] stream 0: video (h264), -vid 0 [lavf] stream 1: audio (ac3), -aid 0, -alang eng VIDEO: [H264] 1280x544 0bpp 49.894 fps 0.0 kbps ( 0.0 kbyte/s) [V] filefmt:44 fourcc:0x34363248 size:1280x544 fps:49.894 ftime:=0.0200 ========================================================================== Opening audio decoder: [ffmpeg] FFmpeg/libavcodec audio decoders libavcodec version 54.23.100 (internal) AUDIO: 48000 Hz, 2 ch, s16le, 448.0 kbit/29.17% (ratio: 56000->192000) Selected audio codec: [ffac3] afm: ffmpeg (FFmpeg AC-3) ========================================================================== ** MUXER_LAVF ***************************************************************** REMEMBER: MEncoder's libavformat muxing is presently broken and can generate INCORRECT files in the presence of B-frames. Moreover, due to bugs MPlayer will play these INCORRECT files as if nothing were wrong! ******************************************************************************* OK, exit. videocodec: framecopy (1280x544 0bpp fourcc=34363248) VIDEO CODEC ID: 28 AUDIO CODEC ID: 15002, TAG: 0 Writing header... [mp4 @ 0x1015c9a50]Codec for stream 0 does not use global headers but container format requires global headers [mp4 @ 0x1015c9a50]Codec for stream 1 does not use global headers but container format requires global headers Then the following repeats itself for every frame: Pos: 0.0s 1f ( 2%) 0.00fps Trem: 0min 0mb A-V:0.000 [0:0] [mp4 @ 0x1015c9a50]malformated aac bitstream, use -absf aac_adtstoasc Error while writing frame. I recognize -absf aac_adtstoasc as an ffmpeg option (does mencoder spawn ffmpeg?), but I don't know how to pass this option on (my hunch is this is not even the origin of the problem).

  Read the article

• Setting up Live @ EDU

  - by user73721

  [PROBLEM] Hello everyone. I have a small issue here. We are trying to get our exchange accounts for students only ported over from an exchange server 2003 to the Microsoft cloud services known as live @ EDU. The problem we are having is that in order to do this we need to install 2 pieces of software 1: OLSync 2: Microsoft Identity Life cycle Manager "Download the Galsync.msi here" the "Here" link takes you to a page that needs a login for an admin account for live @ EDU. That part works. However once logged in it redirects to a page that states: https://connect.microsoft.com/site185/Downloads/DownloadDetails.aspx?DownloadID=26407 Page Not Found The content that you requested cannot be found or you do not have permission to view it. If you believe you have reached this page in error, click the Help link at the top of the page to report the issue and include this ID in your e-mail: afa16bf4-3df0-437c-893a-8005f978c96c [WHAT I NEED] I need to download that file. Does anyone know of an alternative location for that installation file? I also need to obtain Identity Lifecycle Management (ILM) Server 2007, Feature Pack 1 (FP1). If anyone has any helpful information that would be fantastic! As well if anyone has completed a migration of account from a on site exchange 2003 server to the Microsoft Live @ EDU servers any general guidance would be helpful! Thanks in advance.

  Read the article

• Setting up NFS server on Gentoo

  - by StackedCrooked

  I'm trying to set up an NFS server on a Gentoo VM. I've installed nfs-utils-1.2.2 and added the following line to the /etc/exports file: /root/svn 10.0.0.0/255.0.0.0(rw,sync,no_subtree_check) However, when I try to start the nfs service I get the following errors: gentoo-amd64-francis orig # /etc/init.d/nfs start FATAL: Could not load /lib/modules/2.6.24-9-pve/modules.dep: No such file or directory * Exporting NFS directories ... [ ok ] * Starting NFS mountd ... [ !! ] * Starting NFS daemon ... [ !! ] * Starting NFS smnotify ... [ ok ] It complains about not finding the /lib/modules/2.6.24-9-pve/modules.dep file, but the /lib/modules directory doesn't even exist on this machine. Can anyone help me getting it to work?

  Read the article

• Setting up a router as a DNS server only

  - by Jacob R

  I have a Linksys WRT54GL router that I don't need anymore, since I had to buy a 3G capable router (Dovado 3GN). As I only have a 3G connection at home, I want to optimize it as much as possible. I want to setup a caching DNS server, including some blacklisting of ad domains. The router currently runs the DD-WRT firmware. Is it possible to use this router as an ordinary computer, running only a DNS server, disabling all other features such as DHCP, WLAN, etc? Connecting it to my other router, should I simply run a cable into the WAN-port of the Linksys router?

  Read the article

• MailServer Email Account Setting for Outlook Express

  - by hitesh-4259

  Hi, I have developed mail server using postfix + amavisd + spamassassin. Mail sending and receiving works perfect using command prompt. When I am configuring with outlook express, then sending mail works perfact, but error is occured while receiving mail. "your emailserver rejected your login. Verify username and password in your account properties." But my account and password are correct. please help me. Thanks in advance.....

  Read the article

• Setting background color in gvim

  - by petersohn

  I use a terminal with white text on black background (I just like it better), so I wrote the following line in my .vimrc file: set background=dark However, gvim has black on white text. How do I do either of the following: Set the background of gvim to black Check in .vimrc if I'm using gvim I tried this: I started up gvim, and typed echo &term. The answer was "builtin_gui". So I wrote the following into .vimrc: if &term == "builtin_gui" set background=light else set background=dark endif Somehow, it didn't work.

  Read the article

• Setting up a network where packets are traced

  - by Marcus

  My situation is the following: I have an internet connection, which is shared between people. More or less obviously, people is using it to download illegal stuff. Since I'm the owner of the connection, I want to avoid being sued. I don't want to prevent the people from doing the things they want, but I want to be legally safe. Now, I have relatively little competences in network administration, so I was wondering: is it possible to setup a network, where the source and destination of the packets are logged? I would use this to prove, in case of lawsuit, that the traffic was coming from a given machine. if the idea is feasible, is there any wireless router on which I can install linux, where I can install the packet sniffer? how much space could the logs take (containing only the timestamp/source/destination), per GB of traffic? a very rough estimation would be very helpful. if a machine on my network is sending bittorrent packets to a certain IP, would this log be able to reflect the time, source ip and destination ip? I assume that obviously the torrent data would be encrypted and un-decryptable. Am I missing something? Is there a better strategy? Any pointer to documentation would be helpful as well - in that case, I would use this as starting point.

  Read the article

• eAccelerator ignore my new setting?

  - by Mwebe Nkrumah

  Hi, Im using eAccelerator 0.9.5.2, CentOS 5.3, lighttpd 1.4.22 But because eAccelerator is cached in RAM, I needs too much RAM. So Im trying to cache in hard disk. (my website is not generate money, so Im thinking about cheaper solution) So, I modify /etc/php.d/eaccelerator.ini with below codes: extension="eaccelerator.so" eaccelerator.shm_size="12" eaccelerator.cache_dir="/var/cache/eaccelerator" eaccelerator.enable="1" eaccelerator.optimizer="1" eaccelerator.check_mtime="0" eaccelerator.debug="0" eaccelerator.filter="" eaccelerator.shm_max="20M" eaccelerator.shm_ttl="1800" eaccelerator.shm_prune_period="0" eaccelerator.shm_only="0" eaccelerator.compress="0" eaccelerator.compress_level="9" eaccelerator.keys="disk_only" eaccelerator.sessions="disk_only" eaccelerator.content="disk_only" So, the output of phpinfo() as below: http://img175.imageshack.us/img175/1104/screenshggot.png But after using "disk_only" in eAccelerator and restart lighttpd & php-cgi using killall, my RAM usage is still high for php-cgi. Reboot the server also not works. The data is created in cache directory, but RAM usage is still high.

  Read the article

• DNS on Redhat - rdnc: no server specified and no default

  - by Syahmul Aziz

  Hi all. The error as shown in the 2 pictures below: The configurations for named.conf and the zones files as shown below: After applying "alveso" suggestion below. Now, I think there is no error but I still can't ping my own domain www.p0864868.com (10.0.0.1) nor can I do host or nslookup as shown on previous pictures. PLease assist. Thank you in advance. I also attached my the changes that I made to my named.conf as well as my resolve.conf configs as shown below: progress 2: turned on logging by typping "rndc queylog" The output as below when I pinged p0864868.com progress 3: changed permission of 10-0-0.zone and p086868.zone to 644 named:named Still can't ping www.p0864868.com or execute host command. It says something like network unreachable. I don't understand why it refer to I don't what address is that.

  Read the article

• Linux: Setting primary display (nvidia) form command line

  - by Joernsn

  Is this possible? Normally I use disper to enable my external monitor, but I don't think I can force the 2nd monitor to be primary. http://willem.engen.nl/projects/disper/ I've played around with nv-control-dpy included in the nvidia-control source, but I haven't figured out how to do it yet. How to get: http://ubuntuforums.org/showthread.php?t=922956

  Read the article

• Setting up SSL with 389 Directory Server for LDAP authentication

  - by GioMac

  I've got 389 Directory Server running on RHEL 5 with groups, users, posix etc. RHEL clients are authenticating users with LDAP - no problems, everything works perfect, but passwords are sent in plaintext and are visible with network sniffer. So, decided to run with SSL: Created CA - got both private and public CA certificates Using CA certs: generated both of private and public certificates and combined (1st file) for 389DS according to 389DS certificate request, imported with CA public cert to 389DS from graphical console (2nd file). Enabled SSL in 389DS On the client, using authconfig-gtk enabled SSL for LDAP, specified only CA public certificate Doesn't work. Howto? What is the best way to integrate safely?

  Read the article

• Setting up Mail Server (mx.domain.com) using MailEnable in IIS 7.5

  - by Zee Tee

  I have setup MailEnable Standard on my server and have created the PostOffice (domain/mailbox) for the domain which I intend to be using. I have the DNS settings in GoDaddy like this: A (Host) Host: '@' Points To: IP MX Record Priority: 0 Host: 'mx' Points To: @ Is there anything in IIS that needs to be done to make mx.domain.com work as a mail server that can be used in other domain names? Additionally, On the firewall, I have the Outbound port 25 open, not sure, should I be opening port 25 on Inbound as well?

  Read the article

• Help setting up an secondary authoritative DNS server.

  - by GLB03

  We have three Authoritative DNS servers and three recursive/caching DNS servers on my campus. Authoritative servers DNS1- Windows 2003 DNS2- Old Red Hat ----- Replacing w/ newer version DNS3- Windows 2008 (I installed) Caching and Recursive resolvers servers Server1- Windows 2003 Server2- CentOS 5.2 (I installed) Server3- CentOS 5.3 (I installed) I am replacing DNS2 with a newer Red Hat version, but have no documentation on how it was implemented. I have setup caching and windows authoritative servers, but not a linux secondary authoritative server. I have a perl script from the original server that pulls data from our DNS1 server. We use DJBDNS and TinyDNS on our linux servers. Our Network Engineer says the DNS2 server I am replacing is an authoritative server that doesn't need to be caching, but the only instructions I see is for an Authoritative server that does caching as well. Can someone point me in the right directions. I thought I was on the right track with using these instructions but when I query my new dns server I get "No response from server", I have temporarily disabled iptables to eliminate it from being an issue. ps -aux | grep dns avahi 3493 0.0 0.2 2600 1272 ? Ss Apr24 0:05 avahi-daemon: running [newdns2.local] root 5254 0.0 0.1 3920 680 pts/0 R+ 09:56 0:00 grep dns root 6451 0.0 0.0 1528 308 ? S Apr29 0:00 supervise tinydns dnslog 6454 0.0 0.0 1540 308 ? S Apr29 0:00 multilog t ./main tinydns 9269 0.0 0.0 1652 308 ? S Apr29 0:00 /usr/local/bin/tinydns

  Read the article

• Setting cfengine3 class based on command output

  - by gnomie

  This question is very similar to How can I use the output of a command in cfengine3 but the answer does not apply in my case I believe. I want to update a git repository via "git pull" and based on whether that lead to changes trigger some follow up action. Simplified, if there was something like "match output and set class" via some body if_output_matches I would want to use something like this: bundle agent updateRepo { commands: "/usr/bin/git pull" contain => setuidgiddir_sh("$(globals.user)","$(globals.group)","$(target)"), classes => if_output_matches("Already up-to-date.","no_update"); reports: no_update:: "nothing updated"; } body contain setuidgiddir_sh(owner,group,folder) { exec_owner => "$(owner)"; exec_group => "$(group)"; useshell => "true"; chdir => "$(folder)"; } So, is it possible to use the output of a - possibly expensive command - and base some decision on that? The execresult function is no good choice for me as a) the pull may become expensive at times (not recommended following the cfengine3 reference) and b) does not allow to specify user, group, working dir - which is important in my case. The repository is in user space and not owned by root.

  Read the article

• Setting DNS suffix for multiple network adapters in a VM

  - by arun_bh

  Is there a way to set the DNS Suffix for multiple network adapters in a VM using the sysprep file? We are trying to setup Windows 2003 VMs with 2 network adapters. In the one adapter case the sysprep we are able to set the suffix using DNSDomain. But this doesnt work in the 2 adapter case. The The VM is setup corrently though without any issues but one of our apps relies on the DNS Suffix value to work correctly. Thanks in advance.

  Read the article

• Setting up Network File System on Windows XP 64 Bit machine

  - by DotNetGuy

  Hi, Microsoft's SFU is not supported for 64-bit XP OS. Read here - http://support.microsoft.com/kb/920751 I want to set up a NFS Client on 64-bit Windows XP. Any suggestions ?

  Read the article

< Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >