Search Results

Search found 23309 results on 933 pages for 'bit operations'.

Page 699/933 | < Previous Page | 695 696 697 698 699 700 701 702 703 704 705 706  | Next Page >

• Problem building PHP extension module

  - by tixrus

  I'm trying to get GD into my PHP. So I compiled it, made php.ini point to it, restarted apache etc. But no GD. So in apache error log it says PHP Warning: PHP Startup: gd: Unable to initialize module\nModule compiled with module API=20060613\nPHP compiled with module API=20090115\nThese options need to match\n in Unknown on line 0 So a bit of googling says I should not use the phpize I have before configuring and making these. I should use a new one called phpize5. I surely don't have any such thing. Unless its packed up inside something else in my php5.3. distro. Where do you get it. In Ubuntu I could just run sudo apt-get install php-dev, (apparently) and it would just appear by magic. At least that's what the webpage said. Unfortunately I am running MacOSX version Leopard. How can I build this GD module so that it will match the API number in my PHP?

  Read the article

• Multiple IPs on firewall, are these virtual interfaces or what?

  - by Jakobud

  We have 5 static IP addresses from our ISP: XXX.XXX.XXX.180 XXX.XXX.XXX.181 XXX.XXX.XXX.182 XXX.XXX.XXX.183 XXX.XXX.XXX.184 On our firewall box, the NIC that is connected to our cable modem, appears to have all 5 IP addresses set on it. A previous IT guy set this thing up, and I'm not sure exactly what he did. Are these virtual interfaces on this NIC or what? Here is my ip addr output for that NIC: rwd0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether XX:XX:XX:XX:XX:XX brd ff:ff:ff:ff:ff:ff inet XXX.XXX.XXX.180/24 brd XXX.XXX.XXX.186 scope global rwd0 inet XXX.XXX.XXX.181/29 brd XXX.XXX.XXX.186 scope global rwd0:FWB9 inet XXX.XXX.XXX.182/29 brd XXX.XXX.XXX.186 scope global secondary rwd0:FWB10 inet XXX.XXX.XXX.183/29 brd XXX.XXX.XXX.186 scope global secondary rwd0:FWB11 inet XXX.XXX.XXX.184/29 brd XXX.XXX.XXX.186 scope global secondary rwd0:FWB12 inet6 fe80::250:8bff:fe61:5734/64 scope link valid_lft forever preferred_lft forever I'm a bit new to firewalls and networking so I'm just trying to figure out what he had going on here. I know he used Firewall Builder to configure the iptables rules, maybe that has something to do with the "FWB" I see in those names? So my questions are: What is going on here? Virtual Interfaces? Or something else? If we want to put in a second firewall in parallel with this firewall but we only want it to handle traffic to XXX.XXX.XXX.182, how do we get rid of the static XXX.XXX.XXX.182 address on this existing firewall box?

  Read the article

• How to prevent getting infected by rogue security applications

  - by Ieyasu Sawada

  My computer never got infected with a virus before, because I'm using Web of Trust browser plugin, sandboxie and Avast Free antivirus. But today, it got infected with a rogue security application called antivirus.net. I have already removed it using MBAM, SAS, and Kaspersky Virus Removal Tool. And by the way, I was using MSE when my laptop got infected. Seems like the rogue application just killed off the MSE process. And I never even got a warning. I was using the wi-fi from our school, which I think is the cause since most of the computers in our laboratory has rogue applications on it. My question is, how do I prevent this from happening again? It took me about 6 hours to disinfect my computer and I don't want it to happen again. Please enlighten me if these rogue applications really just pop out of nowhere. Note I'm not dumb enough to agree with installing rogue security applications. It just came out of nowhere. I'm happy with MSE, well not after it let antivirus.net penetrate my computer. I've done a little bit of research and it says that it needs the permission of the user to actually install it in the computer: http://www.net-security.org/malware_news.php?id=1245 http://en.wikipedia.org/wiki/Rogue_security_software Is it possible that other computers in our school network have agreed to install those? Or maybe the network admin?

  Read the article

• LSI 9260-8i w/ 6 256gb SSDs - RAID 5, 6, 10, or bad idea overall?

  - by Michael Pearson

  We're provisioning a new production server for our reasonably busy website. Our choice of host have available a 6 drive configuration with a LSI 9260-8i card. My initial thought was to fill all six bays with SSDs (Intel 520 256gb) and set them up in RAID. Good, bad, or terrible idea? Can the card handle it? Should we be using RAID 5, 6 or 10? This would be the first time the provider have filled all six slots for this rackmount with SSDs, so they're a bit hesitant. I'm wondering if somebody else with this card has done something similar in a production environment. We do about 43gb of writes per day and currently use about 300gb of storage. The server acts as webserver, database, and image store for approx 1 million files. The plan is to underprovision the SSDs by approximately 10% to 20% to increase their overall lifespan & performance. The fallback option is 2x480gb SSDs in RAID 1 and another 2x1TB HDDs in RAID 1. The motivation behind this is that the server rental cost difference between 2xSSDs and 6xSSDs is minimal (compared to the overall cost of the rental). We do not have any special high-IOPs requirements. However, if the configuration is known to work, I don't see a good reason to not use it and not have to worry about having separate 'fast and small' and 'slow and large' disks.

  Read the article

• I/O APIC on Virtualbox

  - by RidDeBakTiYar

  I'm trying to use the PIT to do APIC timer calibration, and I want to use the PIT through I/O APIC instead of PIC. On Bochs I get interrupts from the PIT at the asked frequency from the I/O APIC, while on Virtualbox I can't receive a single interrupt. It must be an I/O APIC configuration problem because as I unmask the first PIC entry, the IRQ fires. However that's not what I want. Can you imagine any possible condition that wouldn't make Virtualbox fire the IRQ? I'm not assuming single I/O APIC configuration (even though Virtualbox has only 1). I'm not assuming identity mappings between ISA IRQs and I/O APIC GSIs (using ACPI MADT table to get I/O APIC base address and Int override). I'm setting the Trigger Mode and Polarity bits correctly (on Virtualbox they are set as '00 - default' which means edge high right?). I'm putting the BSP APIC ID into the Destination field (using Physical destination) and vector 0x20. Being the BSP APIC ID 0 on Virtualbox, it ends up with 0x0000000000000020 written to the IOREDTBL. And, just in case I'm getting the wrong values from the Interrupt Override descriptor, I'm setting this value to all the IOREDTBL entries (I know this is very very bad, and it wont be kept as I understand what's going on). The only thing I didn't check out is Local APIC configuration. Actually I'm not writing any value to the BSP LAPIC. Just reading the APIC ID and using it to boot APs through IPIs. And obviously I'm setting bit 11 in the IA32_APIC_BASE MSR to enable the LAPIC. Any ideas? Thanks in advance.

  Read the article

• Can't connect to MS SQL Server database using SSMS

  - by Charles

  I have a database on line with Godaddy (who uses SQL Server 2005). They provide basic management tools, but tell you that for more advanced tools you can connect directly using SSMS. I followed their instructions to ensure my online database will accept remote connections, and can apparently log in using SSMS with success (after giving my hostname and access data). However: Now from in SSMS, when attempting to expand the "Databases" folder tree, I get the following error: Failed to retrieve data for this request. (Microsoft.SqlServer.Management.Sdk.Sfc) An exception occurred while executing a Transact-SQL statement or batch. (Microsoft.SqlServer.ConnectionInfo) The server principal "cmitchell" is not able to access the database "3pointdb" under the current security context. (Microsoft SQL Server, Error: 916) The irony is that 3pointdb isn't my database. It is just another in a long list of databases that show up when I access my Godaddy backend. From SSMS, I selected the default database to be the name of my database, which it did locate on the list when I browsed. Still same error message. It is trying to connect to a database that isn't mine! :( Godaddy support, after a bit of testing, said the problem isn't on their end. it's on mine. – Charles

  Read the article

• MySQL Server Is Slow

  - by user2853965746

  I have two MySQL servers and one was just recently setup. The one I just recently setup is a bit slower than my older one, which kind of bothers me because I don't want my clients to be upset with the speed difference when I launch the new one. The older server runs on Ubuntu (~13.04 I believe) and the new one is on Debian 6. Both servers are 2GB ram, but my newer server is has an SSD, so I thought it might be the same speed if not faster. Anyway, the speed difference isn't too much (both are still under a second, but still noticeable). Whenever I select 50 rows from the user table on my older server (SELECT * FROM users LIMIT 50), I get the results in 0.003 s. There is 100,000+ accounts in that table. Whenever running the same command on the same table with only six dev accounts, it takes 0.069 s. It may not seem like a lot, but it's noticeable when you're used to a fast response. I added skip-name-resolve to the config and it didn't seem to help. Basically I'm asking if anyone knows what can cause a MySQL server to be slow in Debian 6? Should I just drop it and switch to Ubuntu like the older server (I don't think the OS is the problem, but you never know)? The older server is under a lot of use too, it's used a lot for web api's on my website. A lot of connections and stuff, and it still remains fast.

  Read the article

• Huge host CPU usage in idle vmware guest. Ubuntu 10.04 host, Vista SP2 guest

  - by themesandmodules

  I'm experiencing huge host CPU usage with an idle vmware guest. Host: Ubuntu 10.04 32-bit 2.6.32-24-generic-pae. (Very new install, i.e 24 hours ago) Hardware is Dell XPS M1530 laptop, 4GB ram. Intel Core II Duo T9300 2.50Ghz The virtualization setting "VT" or something is enabled in my bios. Guest: Completely fresh install of Windows Vista, upgraded to latest SP2 and all windows updates installed. 1024 - 1512MB ram allocated. Absolutely no other software installed on it, apart from VMWare tools. Situation When the guest is doing absolutely nothing, I watch with sysinternals process watch on the guest. This shows that system idle process is between 70 and 99%, usually around 95%. No actual process doing anything. On the host, I watch with top, I get cpu usage of 20% - 80%, usually around 30%. What I have tried Single and Dual processor available to guest - no change. Turn off all peripherals to guest - no network, drives, usb etc - no change. Turn off 3d acceleration for guest - perhaps a small improvement, or no change. Upping allocated ram to guest from 1024MB to 1512MB - no change. Yelling at vmware - no change. I have experienced a similar issue in the past, which was solved by setting the guest to have 1 CPU. This time that hasn't worked.

  Read the article

• Export NFS path containing "-" (dash)

  - by qdot

  I'm in a bit of a pinch with NFS exports file. Specifically, I can't find a way to export a directory containing "-" in the path name. Manual (exports(5)) states: Also, each line may have one or more specifications for default options after the path name, in the form of a dash ("-") followed by an option list. The option list is used for all subsequent exports on that line only. It then states: If an export name contains spaces it should be quoted using double quotes. You can also specify spaces or other unusual character in the export name using a backslash followed by the character code as three octal digits. Unfortunately, that is not the case. Specifically, if the pathname contains "-", either verbatim, or with \055 or is enclosed in double quotes, it still refers to the name without "-" Any ideas? I have a large number of directories, all of the form /vol/buildsystem-s3c2440 /vol/buildsystem-tao3530 and I'd prefer to have them all available as nfs exports. Short of replacing the "-" with "_" everywhere in the scripts, can it be done with "-" ?

  Read the article

• VPN Trunk Between Cisco ASA 5520 and DrayTek Vigor 2930

  - by David Heggie

  I'm a bit of a VPN newbie, so please go easy on me ... I'm trying to use the VPN trunking capabilities of the DrayTek Vigor 2930 firewall to bond two IPSec VPN connections to a Cisco ASA 5520 device and I'm getting myself tied in knots and hope someone here with more knowledge / experience can help. I have a remote site with two ADSL connections and the DrayTek box. The main office site has the Cisco ASA device. I am able to setup a single IPSec connection between the two sites on either of the ADSL connections' public IP addresses, but as soon as I try to use the VPN bonding, nothing works. The VPN tunnels are both still up, but the traffic is getting lost somewhere. I suspect it's due to the ASA not knowing how to route the traffic back over the VPN - one minute, traffic from my remote office's network is coming from public ip address #1, the next it's coming from public address #2 and it doesn't know what to do. Well, that's my newbie impression of what's going wrong, but I don't really know: If this is really what's happening If what I'm trying to do (bond two VPN connections from a single remote network to improve the bandwidth / resiliency) is possible with the kit I've got Could anyone help?

  Read the article

• Advice needed: warm backup solution for SQL Server 2008 Express?

  - by Mikey Cee

  What are my options for achieving a warm backup server for a SQL Server Express instance running a single database? Sitting beside my production SQL Server 2008 Express box I have a second physical box currently doing nothing. I want to use this second box as a warm backup server by somehow replicating my production database in near real time (a little bit of data loss is acceptable). The database is very small and resources are utilized very lightly. In the case that the production server dies, I would manually reconfigure my application to point to the backup server instead. Although Express doesn't support log shipping natively, I am thinking that I could manually script a poor man's version of it, where I use batch files to take the logs and copy them across the network and apply them to the second server at 5 minute intervals. Does anyone have any advice on whether this is technically achievable, or if there is a better way to do what I am trying to do? Note that I want to avoid having to pay for the full version of SQL Server and configure mirroring as I think it is an overkill for this application. I understand that other DB platforms may present suitable options (eg. a MySQL Cluster), but for the purposes of this discussion, let's assume we have to stick to SQL Server.

  Read the article

• Windows 7 network performance tuning for LAN

  - by Hubert Kario

  I want to tune Windows 7 TCP stack for speed in a LAN environment. Bit of background info: I've got a Citrix XenServer set up with Windows 2008R2, Windows 7 and Debian Lenny with Citrix kernel, Windows machines have Tools installed the iperf server process is running on different host, also Debian Lenny. The servers are otherwise idle, tests were repeated few times to confirm results. While testing with iperf 2008R2 can achieve around 600-700Mbps with no tuning what so ever but I can't find any guide or set of parameters that will make Windows 7 achieve anything over 150Mbps with no change in TCP window size using -w parameter to iperf. I tried using netsh autotuining to disabled, experimental, normal and highlyrestricted - no change. Changing congestionprovider doesn't do anything, just as rss and chimney. Setting all the available settings to same values as on Windows 2008R2 host doesn't help. To summarize: Windows 2008R2 default settings: 600-700Mbps Debian, default settings: 600Mbps Windows 7 default settings: 120Mbps Windows 7 default, iperf -w 65536: 400-500Mbps While the missing 400Mbps in performance I blame on crappy Realtek NIC in the XenServer host (I can do ~980Mbps from my laptop to the iperf server) it doesn't explain why Windows 7 can't achieve good performance without manually tuning window size at the application level. So, how to tune Windows 7?

  Read the article

• Linking to a chat room via XMPP: URI

  - by Coderer

  I found out how to link directly to a chat room on a Jabber conference server -- it took a bit of digging, and I wound up actually looking at the spec before I was sure I was doing it right. I confirmed here, so I'm pretty sure I've got it. The results, though, are puzzling. If I click a link of the style xmpp:[email protected] I get a new chat session with user "dude" at example.com, as expected. If I tack on a nonsense query (xmpp:[email protected]?foobar), it's ignored, which is what the spec says should happen. However, if I use xmpp:[email protected]?join, as in the link above, nothing happens. I dug a little deeper, and found out that on my (Linux) system, xmpp URIs are handled via purple-url-handler, so I dropped to a terminal and ran it manually. The result was that any xmpp URI ran fine except one that includes a ?join query. The ?join query results in a dbus crash, pointing specifically to line 2356 of dbus-message.c -- a little Googling suggests this probably is dbus's less-than-elegant way of telling me that somebody is using dbus incorrectly. Am I crafting my link correctly? Is this an OS or maybe application issue? Does this work on other platforms / browsers / etc? More importantly, is there any easy way to fix it?

  Read the article

• DansGuardian/Squid Traffic doesn't get back to user

  - by DKNUCKLES

  I've purchased a Squid appliance that I'm attempting to implement, however the lack of documentation has left me a bit high and dry. Forgive me if this is a silly question, but this is my first attempt at implementing Squid. From what I can ascertain from the documentation (or lack thereof), the users connect to DansGuardian first at port 8080 where the filtering is done, at which point it forwards it to the Squid appliance at port 3128. The traffic is then sent to the internet. The setup I have is as follows Gateway (MikroTik router) : 192.168.88.1 Squid/DansGuardian :192.168.88.100 Client : 192.168.88.238 Client --- Gateway --- Proxy --- Internet I have set up a simple NAT rule to forward all traffic from the client machine (for testing purposes) to go to the DansGuardian. The traffic seems to get there, although I see a lot of SYN_RECV w/ a netstat -antp command on the virtual appliance machine. From this I gather that the traffic is NOT being routed back to the client machine. Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:8080 0.0.0.0:* LISTEN - tcp 0 0 192.168.88.100:8080 192.168.88.238:55786 SYN_RECV - tcp 0 0 192.168.88.100:8080 192.168.88.238:55787 SYN_RECV - tcp 0 0 192.168.88.100:8080 192.168.88.238:55785 SYN_RECV - tcp 0 0 192.168.88.100:8080 192.168.88.238:55788 SYN_RECV - tcp 0 0 0.0.0.0:10000 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN - Is this a routing issue or an issue with the Squid Appliance?

  Read the article

• NFS high CPU usage

  - by user269836

  Hello, I have a very strange issue. I have next server: Intel(R) Xeon(TM) MP CPU 3.16GHz cat /proc/cpuinfo | grep proce | wc -l 8 free -m total used free shared buffers cached Mem: 28203 27606 596 0 10789 9714 -/+ buffers/cache: 7103 21100 Swap: 24695 0 24695 RAID card *-storage description: RAID bus controller product: MegaRAID vendor: LSI Logic / Symbios Logic physical id: 7 bus info: pci@0000:13:07.0 logical name: scsi2 version: 01 width: 32 bits clock: 66MHz capabilities: storage pm bus_master cap_list rom configuration: driver=megaraid latency=32 resources: irq:134 memory:d8ff0000-d8ffffff(prefetchable) memory:df600000-df60ffff(prefetchable) HDD: 10x148Gb SCSI U320 15k - RAID5 /dev/sdb1 807G 674G 93G 88% /storage /dev/sdb1 /storage ext4 defaults,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,noatime,nodiratime,noacl,errors=remount-ro 0 1 network cards ethtool -i eth0 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ethtool -i eth1 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ifconfig bond0 Link encap:Ethernet HWaddr 00:0f:1f:ff:d6:4d inet addr:192.168.15.71 Bcast:192.168.15.255 Mask:255.255.255.0 inet6 addr: fe80::20f:1fff:feff:d64d/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:1062818202 errors:0 dropped:3918 overruns:0 frame:0 TX packets:1041317321 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10000 RX bytes:258867684559 (241.0 GiB) TX bytes:396569192650 (369.3 GiB) this server running only nfs-kernel-server uname -a Linux nas2-backup 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux Debian 6. What do I have, once per day or two, LA goes up, it can be reached around LA: 40 but if I do: nfs-kernel-server restart. Every thing is OK. But on the next day or a little bit later, LA goes up again. Servers are connected to d-link dgs 1016d with 24 GBits ports. I have tried everything to find out what the problem is. Why it's happening, but still I can not resolve this issue. Any ideas on what is happening here?

  Read the article

• How to restore broken Ethernet functionality on Mac G5 running Mac OS 10.4.11 (Tiger)

  - by willc2

  I had a disk error that rendered my Mac unbootable. I repaired it with Tech Tool 4, but now networking does not work. Network Preferences reports that my Ethernet cable is unplugged. I know this is bogus because when I boot from an emergency partition, networking works correctly. Furthermore, wireless networking is also broken, which I tested with a known-good Wi-Fi dongle. Whenever I try to change Network Port Configurations by creating a New or Renaming an existing one, example: I get this message in the console: Error - PortScanner - setDevice, device == nil! Error - PortScanner - setDevice, device == nil! In sets of two as shown. When I try to invoke the Network Diagnostics app, it immediately crashes. My first thought is to reinstall Tiger with the Archive and Install method so I don't have to reinstall all my applications but I have lost my Tiger installer disk. My next thought is to buy Leopard for $107 on Amazon. If there is any way I can just repair my Tiger install I would be happy to save that money, though. This is not my main machine and I am loathe to put more money into it. How can I recover my network functionality? UPDATE: I found my Tiger install disk and tried an Archive and Install. It failed with an unhelpful error message along the lines of "Can't install, try again". I tried again but had the same error. My guess is, some corrupt or missing file in my User folder is preventing migration. I have a backup created with Super Duper that is a bit out of date but will startup the machine (with functional networking). I would love to just copy over the file(s) that got messed up but I don't even know where to look. What is the likely location of the System files that would cause the aforementioned symptoms?

  Read the article

• How can I manage AWS VPC ssh access accounts and keys across multiple instances?

  - by deitch

  I am setting up a standard AWS VPC structure: a public subnet some private subnets, hosts on each, ELB, etc. Operational network access will be via either an ssh bastion host or an openvpn instance. Once on the network (bastion or openvpn), admins use ssh to access the individual instances. From what I can tell all of the docs seem to depend on a single user with sudo rights and a single public ssh key. But is that really best practice? Isn't it much better to have each user access each host under their own name? So I can deploy accounts and ssh public keys to each server, but that rapidly gets unmanageable. How do people recommend managing user accounts? I've looked at: IAM: It doesn't like like IAM has a method for automatically distributing accounts and ssh keys to VPC instances. IAM via LDAP: IAM doesn't have an LDAP API LDAP: set up my own LDAP servers (redundant, of course). Bit of a pain to manage, still better than managing on every host, especially as we grow. Shared ssh key: rely on the VPN/bastion to track user activities. I don't love it, but... What do people recommend? NOTE: I moved this over from accidentally posting in StackOverflow.

  Read the article

• SQL Server 2005 SP3 on Windows 7 - No Management Studio

  - by Mike Thomas

  I've been trying for a day and a half now to get SQL Server 2005, DEV edition, to work on Windows 7, 64 bit prof. I install from the disk, then run SP 3. I get a failure on the Client Components section of the Installation Progress along with this vague message - Product : Client Components Product Version (Previous): 1399 Product Version (Final) : Status : Failure Log File : C:\Program Files\Microsoft SQL Server\90\Setup Bootstrap\LOG\Hotfix\SQLTools9_Hotfix_KB955706_sqlrun_tools.msp.log Error Number : 1712 Error Description : MSP Error: 1712 One or more of the files required to restore your computer to its previous state could not be found. Restoration will not be possible. I've uninstalled all Visual Studio and tried to make this as clean as possible, and have read a lot of the blog posts, but am really at my wits end about this. I am not a DBA, but I use SQL Server all the time when coding and testing apps. Does anyone have any ideas as to where I can get this sorted out? I've been ati this for a long time and have never encountered an installation as bad as this one. Thanks Mike Thomas

  Read the article

• How to monitor changes in the frequency of network latency spikes over time?

  - by dequis

  I'm currently trying to troubleshoot an issue with my network in which I get latency spikes up to 200 seconds (normally around 50 secs) in an apparently random way at apparently random moments of the day. While trying to find what part of my messy network needs to be blamed (outside of the scope of this question - discussed a bit on chat), I realized I have no reliable way to confirm that a change actually improved anything. So far, the main way in which i notice this is that irssi shows [Lag: 15 (??)] in the statusbar, increasing every 5 seconds, and all other connections seem to be affected too. Since this depends on my observations, it's not a very reliable method to know how often it really happens. Note that just sending ICMP pings is probably not enough, but that's just my guess. It might be a "bufferbloat" issue, it might be packet loss, it might only apply to persistent connections. I suspect this because a few months ago, when the issue started, I had a "ping" command running in background and it didn't show anything weird at all during the latency spikes. This seems to have changed now (pings don't go through), but still, I'd prefer something more robust.

  Read the article

• Hard drive not correctly recognized on a new Windows 7 installation, but works correctly on Windows XP

  - by david

  I'm having problems configuring a hard disk in a brand new, clean Windows 7 installation. System specs: Hard disk: WD VelociRaptor WD6000HLHX (600 GB, 10000 RPM) Motherboard: Gigabyte Z77X-UD3H BIOS SATA mode set to AHCI (not RAID), with disk connected to SATA0 (6 Gb/s port). Windows 7 Enterprise SP1 64-bit The disk is recognized by the BIOS and is correctly identified, with the name and size correctly reported. Windows recognizes the disk itself and reports the device is functioning correctly, but it doesn't appear in Explorer. Disk Management shows the drive, but incorrectly states that it is uninitialized and has no partitions. If I try to initialize the drive, I get an error saying that "the system cannot find the file specified" (what file?). Before connecting the drive to the new machine, I partitioned and formatted it under Windows XP SP2, creating 2 partitions (MBR, not GPT) and copying over a boatload of data. However, none of this data appears under Windows 7. If I put the disk back into the Windows XP machine, I can access the disk and all of its data. Is it possible to get Windows 7 to correctly recognize the disk without having to erase it and start over? If so, how do I do so? I checked this question, which seems to cover the same issue, but it didn't help.

  Read the article

• Windows XP consuming drive letters

  - by billdehaan

  This one's a bit of a stumper. I'm running XP SP3, current with all fixes, etc. My problem is that I can assign a drive letter to a container file (explained below), it works just fine. But once I close the container, the drive letter is no longer available until the next boot. I've got some confidential data that I've placed in a container volume. I've used TrueCrypt (www.truecrypt.com) and FreeOTFE (www.freeotfe.org), with both installed and portable versions for both, with the same result. I open the container file, assign it to a drive letter (say R:), and run some portable apps that are within the volume. When I'm done, I close the container, and the drive letter is released. Fine so far. However, when I attempt to re-open it, the previous drive letter (in this case R:) is no longer available. It's not mapped to anything, it's just unavailable. Even attempting something like "subst R: C:\" returns "Invalid Parameter - R:". I can use the S: drive, no problem, but the next day I have to use T:, then U:, etc. Eventually, I have to reboot to reclaim all of of the drive letters. Unfortunately, everything I've read about drive letters relates to USB assignments, which doesn't apply here. I've tried the "show hidden" command (set devmgr_show_nonpresent_devices=1) with no success. And the Disk Management tool doesn't apply either, since it's not a physical drive. Does anyone know where Windows keeps the list of drive letters? And is there anything short of a reboot that can be used to reset it?

  Read the article

• /usr/bin/python (Python 2.4) was deleted on CentOS 5. I compiled from source but yum is still broken. How can I get everything back to the way it was?

  - by Maxwell

  I saw a lot of other questions like this but none of them answered the exact part I am having trouble with (actually installing the Python RPM). Someone on my system deleted /usr/bin/python and /usr/bin/python2.4 on my 64 bit CentOS 5.8 installation. I recompiled Python 2.4 from source, but now whenever I try to yum install anything I get the following error: [root@cerulean-OW1 ~]# yum install httpd There was a problem importing one of the Python modules required to run yum. The error leading to this problem was: No module named yum Please install a package which provides this module, or verify that the module is installed correctly. It's possible that the above module doesn't match the current version of Python, which is: 2.4 (#1, Dec 16 2012, 09:16:56) [GCC 4.1.2 20080704 (Red Hat 4.1.2-52)] If you cannot solve this problem yourself, please go to the yum faq at: http://wiki.linux.duke.edu/YumFaq I checked http://wiki.linux.duke.edu/YumFaq and it said the following: If you are getting a message that yum itself is the missing module then you probably installed it incorreclty (or installed the source rpm using make/make install). If possible, find a prebuilt rpm that will work for your system like one from Fedora or CentOS. Or, you can download the srpm and do a rpmbuild --rebuild yum*.src.rpm I tried going to http://rpm.pbone.net/index.php3/stat/4/idpl/17838875/dir/centos_5/com/python-2.4.3-46.el5.x86_64.rpm.html to install Python, which resulted in the following error: [root@cerulean-OW1 ~]# rpm -Uvh python-2.4.3-46.el5.x86_64.rpm error: Failed dependencies: python-libs-x86_64 = 2.4.3-46.el5 is needed by python-2.4.3-46.el5.x86_64 So I tried installing python-libs-x86_64, which resulted in the following: [root@cerulean-OW1 ~]# rpm -Uvh python-libs-2.4.3-46.el5_8.2.x86_64.rpm warning: python-libs-2.4.3-46.el5_8.2.x86_64.rpm: Header V3 DSA signature: NOKEY, key ID 192a7d7d Preparing... ########################################### [100%] package python-libs-2.4.3-46.el5_8.2.x86_64 is already installed file /usr/lib64/libpython2.4.so.1.0 from install of python-libs-2.4.3-46.el5_8.2.x86_64 conflicts with file from package python-libs-2.4.3-46.el5_8.2.x86_64

  Read the article

• Which database to use and system/db administration by layman [closed]

  - by blah

  So my friend and I got briliant ;) idea for a business. Since it is not predictable whether it will work out or not, we decided to keep cost as low as possible to start with, in particular not to hire anyone. If it will work out as expected it will generate enough profit to hire professionals in few months. But for the first few months we'll be doing everything by ourselfs. He's a business/finance major, and I'm a software developer, so obviously I have to take care of IT :) It will be a webapp, written in python/django. My questions regarding this project: 1) What database should I choose? I'm experienced with oracle, and have been working with SQL Server for a while, but both of them are too expensive(at least now). It's a developer experience, I've never done any dba stuff. I'm looking for something free(as in beer). Looks like MySql or PostgreSQL are most popular in this sector. I would appreciate any comments on which db to choose. I'm open to any suggestions(it doesn't have to be MySql or Postgre). Here's what I know about data: It will be almost dates and numbers, a little bit of text. Searched mainly by dates. Data will almost never be updated, mostly inserted and browsed. From 30k to 300k new records/month. 2) Servers. My idea is to rent two dedicated servers. During normal operation one would be a web server(debian/apache), other would be a db server(debian/?). My recovery plan is to install everything on both, and in case of trouble with one of machines just run everything on the other one. Does it even makes sense? Any other tips appreciated. Thanks.

  Read the article

• No digital audio output with Asus Xonar DG

  - by Lunatik

  I've purchased an Asus Xonar DG as replacement for faulty onboard audio in a Medion 8822 as it has an optical output which is all I really need to feed my HTPC. I uninstalled the previous drivers/devices, switched the PC off, inserted the Asus card, powered up, disabled the onboard audio in the BIOS, then installed the driver that came on the CD (same version as on Asus' website as of today) and everything went perfectly - no errors. I set the audio devices up in Windows and in the Asus utility (SPDIF enabled, 6-ch audio) as I would expect to see them work, but the only thing is I have no digital audio from test tones within Windows/the Asus utility, PCM audio or Dolby Digital from DVD. Analogue audio is fine. I've uninstalled things and reinstalled a couple of times now, as well as trying almost all combinations of analogue/digital outputs but can't get it sorted. Does anyone have any tips on how to get this working? This card has just been released so there isn't much out there to go on. Notes: The light on the toslink port is lit. OS is Vista 32-bit SP2 and all up to date, pretty much a fresh install with almost no 3rd party applications installed This page seems to suggest that a digital output device in Windows is not needed with Xonar cards as it was with the previous Realtek so I have it set to Analog. The only other output device is S/PDIF pass-thru

  Read the article

• vCenter 5.1 SSO Configuration option not available in Web Client?

  - by goober

  Problem I just finished separately installing vCenter Server 5.1. I installed the components separately but on the same machine using a local SQL 2008 R2 DB (not SQL express). Everything appears to be working correctly with the exception of SSO. It doesn't find the AD server. This is to be expected (see below) but I don't know how to fix it. Potential Leads / Steps taken During the install of SSO, I was logged on as a local administrator (waiting on central IT dept to create a service account). As a result, I received a message saying that SSO wouldn't be able to automatically locate the AD. (fair eonugh) After I read up on it a little bit, I believed I could go into the SSO Configuration option in the Web client, like so: However, what I actually see is: I also notice that the "SSO Users and Groups" entry is not there. Betting that has something to do with it as well. Question How can I get the "Configure" Option to show up for SSO? Overall goal: How can I manually enter the AD server in this scenario while logged in as a local administrator? References VMWare vCenter 5.1 Installation: Part 9 (Optional SSO Configuration) [Derek Seaman's Blog] (used the image of correct configuration menu)

  Read the article

< Previous Page | 695 696 697 698 699 700 701 702 703 704 705 706  | Next Page >