Search Results

Search found 21319 results on 853 pages for 'state management'.

Page 704/853 | < Previous Page | 700 701 702 703 704 705 706 707 708 709 710 711  | Next Page >

• connecting to server with multiple nics in other vlan

  - by Thierry

  I have a windows 2003 server with 3 nics on 3 vlan's (this is in domain 1). nic 1 has a default gateway to my router/firewall (sonicwall). In nic 2 and 3 I have left it empty, because it is advised like that everywhere. Within this domain and VLAN's 1-3 everything works fine. BUT... I have a second domain (domain 2) with a 4th Vlan (all 4 VLAN's connected to the same router/firewall) from which my clients need to access the 2003 server in domain 1 (it's my antivirus management console for both domains). when i ping the server from my vlan4 by it's FQDN, it randomly chooses ip from nic 1, 2 or 3 from my 2003 server. (logically because that server is know in DNS with it's 3 IP-addresses. And that is needed for my VLAN's 1-3) I don't really have a problem with that. BUT, I only get an answer of NIC1 (which sounds logically to me, because it's the only one with a gateway). It is not a router problem, because I'm testing in this phase and ping from vlan4 to any machine in vlan1, 2 or 3 that has 1 nic works just fine. If i add a gateway to nic2 and nic3, I get answer from all 3 nics and this works fine. But I know it's adviced to not do that. Can anyone give me advice in this particular case? Would it really be a problem to add a gateway to nic 2 and 3? They would be pointing to the same router/firewall (only with different ip-address, based on the vlan). Or is there another good solution to fix this problem? Thank's in advance, Thierry.

  Read the article

• How do I fix error 1303 during TI Connect install?

  - by smoth190

  I recently purchased a TI-84 Plus graphing calculator, and I'm trying install the TI Connect software in order to connect the calculator to my computer via the USB cable. Unfortunately, I'm getting this error while trying to install the program: Error 1303. The installation has insufficient privileges to access this directory: E:\Data\Timothy\Documents\MyTIData. The installation cannot continue. Log on as administrator or contact your system administrator. However, my account is the only account on my PC, and it has administrative privileges. I've also tried running the installer with Run as Administrator, but with no luck. If I create the folder MyTIData manually, I receive this error: Error 1317. An error occurred while attempting to create the directory: E:\Data\Timothy\Documents\MyTIData I've reapplied the security settings to the E:\Data folder (and all its sub-directories) to Full for my account. I've also gone into Computer Management, and given SYSTEM full privileges for the entire disk. I've also logged out, logged back in, restarted, etc. but still, no luck. Now, I should mention that my Documents folder is not at the default location. I changed it due to my C: disk being a 90GB SSD, so I moved all my personal data onto the extra storage disk (which is ~1TB). I don't know if that is causing the issue, but it can't hurt throwing it out there. So why can't I install this program? Google'ing the problem brings up this error for various other installers (such as Visual Studio and Microsoft Office), but nothing for TI Connect. All the solutions are the same: Give the folder Full privileges...but I've already done this! I've also tried running the installer with and without the calculator plugged in, but it didn't change anything. In the prompt that contains the error, repeatedly clicking Retry or waiting a few moments before clicking Retry also produces no result.

  Read the article

• Getting access to physical drives in ESXi v5.5 installation on Dell PowerEdge R710 with PERC 6/i

  - by Big-Blue

  I've acquired a Dell PowerEdge R710 server a few days ago, which includes a PERC 6/i RAID controller. The server is now fitted with a SATA SSD, one SAS drive and four SATA HDD's, all of which I would like to be passed through to ESXi in an "as-is" state, without creating any logical drives in the RAID controller. Now, the ESXi v5.5 installation image I grabbed from the Dell homepage starts just fine but only lists the logical drives and connected flash drives as possible installation targets, not any of the physical drives. If I create a small logical drive on my SSD (which the PERC 6/i detects as SATA-SSD type), the ESXi install wizard lists the SSD value on that drive as false; which is far from optimal. I have also tried disabling the RAID controller entirely in the setup, but that also did not help. Everything that should enable passthrough is enabled in BIOS, but that shouldn't be a concern at this early stage of the ESXi installation. How would I be able to install ESXi v5.5 to a part of my SSD that is connected to the storage controller, while giving it entire physical access to the disk (to allow for SMART values to be read etc.)?

  Read the article

• Iptables rules, forward between two interfaces

  - by Marco

  i have a some difficulties in configuring my ubuntu server firewall ... my situation is this: eth0 - internet eth1 - lan1 eth2 - lan2 I want that clients from lan1 can't communicate with clients from lan2, except for some specific services. E.g. i want that clients in lan1 can ssh into client in lan2, but only that. Any other comunication is forbidden. So, i add this rules to iptables: #Block all traffic between lan, but permit traffic to internet iptables -I FORWARD -i eth1 -o ! eth0 -j DROP iptables -I FORWARD -i eth2 -o ! eth0 -j DROP # Accept ssh traffic from lan1 to client 192.168.20.2 in lan2 iptables -A FORWARD -i eth1 -o eth2 -p tcp --dport 22 -d 192.168.20.2 -j ACCEPT This didn't works. Doing iptables -L FORWARD -v i see: Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 33 144 DROP all -- eth1 !eth0 anywhere anywhere 0 0 DROP all -- eth2 !eth0 anywhere anywhere 23630 20M ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- eth1 any anywhere anywhere 175 9957 ACCEPT all -- eth1 any anywhere anywhere 107 6420 ACCEPT all -- eth2 any anywhere anywhere 0 0 ACCEPT all -- pptp+ any anywhere anywhere 0 0 ACCEPT all -- tun+ any anywhere anywhere 0 0 ACCEPT tcp -- eth1 eth2 anywhere server2.lan tcp dpt:ssh All packets are dropped, and the count of packets for the last rule is 0 ... How i have to modify my configuration? Thank you. Regards Marco

  Read the article

• error: unexplained error (code 130) at rsync.c(541) [sender=3.0.7]

  - by brazorf

  This error: unexplained error (code 130) at rsync.c(541) [sender=3.0.7] error is happening after i changed router. Actually, i found out that this error just happens on a ctrl+c signal, so it could be not representative about the error itself. The command i run is very basic: rsync -avz --delete /local/path/ username@host:/path/to/remote/directory Basically, the rsync just stuck there and nothing's happening, until i ctrl+c. After interrupting the process i got the error in subject. I past the whole thing here: rsync -avvvvz --delete /source/path/ username@host:/path/to/direectory cmd=<NULL> machine=HOSTNAME user=username path=/path/to/direectory cmd[0]=ssh cmd[1]=-l cmd[2]=username cmd[3]=HOSTNAME cmd[4]=rsync cmd[5]=--server cmd[6]=-vvvvlogDtprze.iLsf cmd[7]=--delete cmd[8]=. cmd[9]=/path/to/direectory opening connection using: ssh -l username HOSTNAME rsync --server -vvvvlogDtprze.iLsf --delete . /path/to/direectory note: iconv_open("UTF-8", "UTF-8") succeeded. ^C[sender] _exit_cleanup(code=20, file=rsync.c, line=541): entered rsync error: unexplained error (code 130) at rsync.c(541) [sender=3.0.7] [sender] _exit_cleanup(code=20, file=rsync.c, line=541): about to call exit(130) The authentication runs on ssh via rsa key. I tried basic troubleshoot such as: ping the remote host ssh -l username remote.host check software firewall logs i asked the remote host sysadmin to check for logs, and when i run that command a ssh connection is actually being established and i can state there is no comunication/authentication/name resolution issue here. Rolling back to old router make this work again. Both client and server are running ubuntu 10.04. Try to take a look at my router configuration, where i'm no experienced at all, but i didnt see any "suspect" (what i was looking for is firewall blocking something) setting. The router itself is DLINK DVA-G3670B. Any suggestion? Thank You F.

  Read the article

• XP/Intel wirelss only showing 'hpsetup' ad-hoc network that isn't there

  - by ewall

  Trying to help my friend with her work XP laptop, which recently stopped seeing any wireless SSIDs except the SSID 'hpsetup' (presumably from a wireless-enabled HP printer). Relevant information: The laptop is a Lenovo T500 (Centrino 2 chipset) with XP SP3. The network adapter is Intel WiFi Link 5300 AGN (built-in). The latest version (13.5) of the Intel drivers only are installed, not the Intel config software, so XP is using the Wireless Zero-Config manager. The wireless router is a NetGear WGR614 v7 with 802.11b/g. The SSID is broadcasting, and all the other laptops in the house can see and connect to it. On the laptop, I have tried repairing the network connection, disabling power management, turning off 802.11a & n radio, and more... but it didn't help. Some of the wireless settings are managed by Group Policy from her office (I get the "At least one of your changes was not applied successfully to your wireless configuration" message). It is enforced to connect to "Access point (infrastructure) networks only". The real kicker is that my laptop does not an SSID named 'hpsetup' here, but it can see several broadcasted SSIDs including the one we want, while my friend's laptop doesn't see any SSID except 'hpsetup'. Any suggestions?

  Read the article

• Adding subnet to a vsphere with single vcenter and esxi host

  - by Ilya Rakhlin

  Let me start of by saying that I do not specialize in networking, I am in the process of adding additional VMs to a testing environment and wanted some recommendations. In this case I am running a single ESXI 5.1 host and a single Vcenter management server. The problem is, I need another range of IP addresses added to the existing setup; hopefully without reconfiguring everything. Currently the esxi host is configured to IP: 192.168.100.200, gateway: 192.168.100.1 and subnet: 255.255.255.0. All of the VMs are running some version of linux with hard coded IP addresses in that range, and using that subnet. The VMs I am about to deploy I want to be on the 192.168.101.X network. Is it possible to add an additional subnet to this existing system that will also communicate with the current subnet? The esxi host has 6 physical NICs but only one connected as it is only a testing system; not sure if that matters. Are there any other ways to accomplish this hopefully without restarting or at least reconfiguring the IP addresses for each VM? Reason: Due to the configuration of the VMs to run the applications that we need I am using a large amount of the current IPs in the potential range (mostly VIPs). I will be setting up a new version of this “environment” while keeping the old one, thus potentially running out of IP addresses.

  Read the article

• Sending mail results in "Sender address rejected: Domain not found"

  - by user1281413

  The setup: WHM/CPanel CentOS 5 server running Exim and Courier for mail services, and BIND for domain name services. I recently moved servers. The old server was running a HIGHLY similar configuration, and all accounts were ported via WHM. However, the server is unable to send, and sometimes receive email. Errors I am seeing (when I do get an error mail back) state: 450 4.1.8 : Sender address rejected: Domain not found Edit for clarity: this is the error response from remote mail servers. Numerous independent mail servers come back with the same error. (Email address is merely one valid example) My first instinct of course was to check the domain records. However, k-t.org appears to have a valid record (including an MX record), even after running it through domain checks on a completely different server elsewhere and online. Note that the issue appears to happen with all the domains hosted on the server, not just k-t.org I have also ensured that a PTR was created. My Googling has only lead me to people who had fairly basic DNS mistakes, but either I'm blind/dumb (possible, DNS is not my strong suite), or it's something that is a bit more archaic. I've run out of ideas, and I can't seem to find anything that could explain why servers are unable to resolve the domains. There doesn't seem to be anything missing or incorrect.

  Read the article

• What XMonad Configuration Best Replicates Default Ion3 Behavior and Feature Set?

  - by mtp

  Not being very familiar with Haskell and lamenting that Ion 3 is now abandonware, I am curious if anyone out there has found a way of replicating the default Ion 3 behavior and aesthetics in XMonad. If I can't have a near-exact replica of Ion 3-style behavior in XMonad, here is what would be critical to me: Virtual desktops that are empty by default and that spawn full-screen applications, which can be split horizontally or vertically evenly, leaving an empty adjacent pane. The panes, which house open windows, are manually resizable, preferably via keyboard. The panes exhibit tabbed behavior, meaning that they can house multiple windows. Windows can be tagged and moved between panes / virtual desktops via keyboard sequence. A given window may be temporarily exploded into full-screen mode via keyboard sequence. Each new virtual desktop starts in the same state—i.e., with one pane. Each virtual desktop may have its panes divided independently of other virtual desktops. From my investigation, it appears that there are several configurations that provide #3. For as much as I want to spend the time to familiarize myself with Haskell, I just simply don't have time. Any suggestions would be greatly appreciated. As far as I can tell, Ion has no conception of master pane or window, so this behavior is not desired.

  Read the article

• Asus K50I sound issues

  - by MrStatic

  I have an Asus K50IJ (Bestbuy) laptop and have issues with my sound. Speakers themselves work fine but when I plug into the headphone jack it auto mutes the front channel and no sounds comes out of either the speakers or the headphones. If I then unmute the channel I get sound from both the speakers and the headphones. alsamixer shows the Headphone channel as all grayed out. /etc/modprobe.d/alsa-base.conf I have tried snd-hda-intel model="asus-laptop" and snd-hda-intel model="asus" In Sound Preferences I have gone to output and changed the Connector to 'Analog Headphones' that results in no sound from either speakers or headphones. As one forum suggested I tried to comment out blacklist snd_pcsp in the blacklist.conf which resulted in no change. lspci -v shows: 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) Subsystem: Santa Cruz Operation Device 1043 Flags: bus master, fast devsel, latency 0, IRQ 45 Memory at fe9f4000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel Capabilities: [130] Root Complex Link Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel

  Read the article

• Should an HA failover occur in this scenario?

  - by joeqwerty

  I'm running vSphere 5 in an HA cluster across two hosts (vsphereA and vsphereB). I have the HA cluster configured for host monitoring and datastore heartbeat monitoring with admission control disabled (hopefully I rightfully understand that datastore heartbeat monitoring prevents inadvertent and unwanted HA failovers due to management network isolation). Each host has a single connection to a dedicated iSCSI network and iSCSI target (no MPIO). All vmdk's for all VM's exist on the iSCSI datastore. As a test of HA I disconnected the iSCSI connection on vsphereB and was surprised to see that the running VM's on vsphereB continued to run on vsphereB. The powered off VM's were showing as inaccessible (which I expected due to the fact that they weren't running and the connection from vsphereB to the iSCSI target was severed) but the running VM's continued to run and continued to be "owned" by vsphereB. I expected to see an HA failover occur for those VM's and expected to see them "owned" by vsphereA after the HA failover (which didn't occur). I'm at a loss to understand why an HA failover didn't occur for those VM's. Am I misunderstanding in which cases an HA failover should occur?

  Read the article

• IP6 seems to be enabled - How do I configure it without interfering with IP4?

  - by Mister IT Guru

  I noticed that some of my Centos boxes have IP6 enabled, and seem to have addresses. I have no problem with this, but I would like to get a handle on it, and even connect to them using IP6. This would really help if for any reason DHCP has a hiccup. But I'm a bit lost as to where the configuration on my CentOS box is. (I am also on google researching this, but I like server fault! :) ) I am hoping that I would be able to log into this via the VPN because every now and then that DHCP device has a bad morning, and needs to be restarted. (I'm also looking into this issue, but someone else handles that, management separation gone mad!) It's a remote client, so it would be a lot easier for me to connect to these systems which seem to self configure, to use that as a pivot via ssh tunnels to get to other remote devices to continue to manage them, while out main route is fixed. I guess, my questions are How can I configure IP6 without interfering with IP4, and On CentOS, can I influence this auto configuration I seem to be seeing?

  Read the article

• Why can't I physically access my machine after a remote session?

  - by Steve Crane

  I have a Dell Optiplex 960 desktop running Windows 7 64-bit at work. I typically leave it locked rather than logged off when I go home, so that I'm able to remote in from home and continue working if I wish. This is where the problem comes in. If I don't remote in there is no problem and I can simply unlock the next morning. It's when I do remote in that I have a problem. Remote sessions work as expected but when I get to work the next morning the machine appears to have gone into a sleep or hibernate state, from which no amount of mouse moving or keyboard pounding will wake it. The machine is not hanging as remote sessions to it are still possible; it seems that physical access from it's own mouse and keyboard are lost. The only way to gain access is to press and hold the power switch for several seconds until the machine shuts down. Of course this means Windows does not gracefully shut down and after powering up it takes several minutes for the machine to boot and reach the login prompt; presumably while it checks the disk. Has anyone else seen something like this?

  Read the article

• Router startup problem

  - by gfmoz

  I have problems with my Tilgin Vood Router. As I try to start my router by turning the power on (captain obvious), it generally doesn't work the first 3-4 times. This is getting very annoying. Five minutes after turning the power on the router's signal LEDs don't blink in the way they should do in a connected state. I can connect to my routers web configuration interface through my PC connected to it via LAN though I can't access the internet. It usually takes the router five minutes to get to the point where it should be connected to the internet but as it doesn't work the first times. So I turn on my router 3-5 times, let him work 5 minutes and then suddenly, after turning the pow*emphasized text*er off and on again it all works. The problem is regarding startup only, when I get it to work everything runs as smooth as a 1980-s text-based C++ game on a 3ghz machine. I also have to restart my PC too in order for everything to work. - How can I solve this problem? - Just leave the router turned on all time? I prefer a daily IP switch, though. - May the problem have something to do with my PC? There is another one connected to the router too and it doesn't work there either.

  Read the article

• SQL Server 2008 login problem with ASP.NET application: Failed to open the explicitly specified database

  - by eulerfx

  I am running SQL Server 2008 Express Edition on Windows Server 2008 with an ASP.NET application which must access the server. The ASP.NET application is associated with an application pool that runs on the NetworkService account. This account in turn has a Login and User record on SQL Server in the required database. When I attempt to run the ASP.NET website I get a blank page and when viewed in the error log, I seem to be getting this information event record: Login failed for user 'NT AUTHORITY\NETWORK SERVICE'. Reason: Failed to open the explicitly specified database. [CLIENT: myLocalMachine] The connection string has Trusted_Connection=True; and the required database specified. When I explicitly specify the user name and password I get another login error stating the password is incorrect, even though the same un/pw combination works through SQL Server Management studio. The NETWORK SERVICE account seems to have all the required privileges for the database. Also, I made a test ASP.NET website project which does a simple select from a table in that database, and using the same config file I am not getting the error and it seems to work. Is it something to do with trust levels then, because the original ASP.NET web app references various DLLs including open source libraries. Also, the application does not seem to be able to write to the event log itself, throwing a security exception, even though everything in the config files, including machine.config states the app is in full trust.

  Read the article

• Un-install network printer drivers from Win7 64 Home Premium

  - by AkkA

  I recently bought a NAS device that has print server functionality through USB. The printer was already installed and fully working on another Win XP box, set up that box to see the printer over the network and it prints fine. I tried to install the printer on my Win7 laptop (64 bit, Home Premium), but got the wrong drivers somehow, or it just refuses to work. I need to completely un-install the printer drivers and start from scratch. Removing the printer (by going to the printers folder, right click and remove) does not actually un-install the drivers. It only removes the printer from active use. Even if I try to re-install new drivers it will load the old ones. I have read a few things on the net that say to load up a device snap-in or something of the sort into Computer Management, but this seems to be valid for Win7 Pro or greater, the function everyone tells you to use isnt available in Home Premium. Is there anything I can use to manage device driver files in Home Premium? I want to completely remove them from the computer.

  Read the article

• Site hanging in iis7 - how do I troubleshoot?

  - by Chris Foot

  I am currently having a problem with a windows 2008 server running IIS 7. The server runs several sites but only seems to have the issue with one particular site. Every so often, the whole server slows to a crawl with nearly all requests timing out! Invariably, when we log in to take a look there is always an IIS process using up around 90% cpu. Looking into the worker processes in IIS there are usually one or two requests that have been running for a long time. They are always in the ExecuteRequestHandler state with ManagedPipeline as the module name and the current ones i'm looking at have been running for 7686248 (what units is this in, it doesn't say?). It is also not always the same page, in fact we have seen at least 3 different pages listed under url when this has happened. It seems that the only way to bring the server back to life is to kill the 90% process! The site is running under .Net 4.0 and the code on it is very similar to other sites on the server which do not have the problem! How do I start troubleshooting this?

  Read the article

• Regarding AD Domain controllers and remote branch offices

  - by Alex

  We have central HQ building and a lot of small branch offices connecting via VPN and want to implement AD (If you can believe we still haven't). We want everyone to log in using domain accounts and be policed centrally. We are OK with having a RODC in a branch office with like 10 computers. But we have these small branches with two to four PCs only. Some of these branches connect to HQ via IPSec site-to-site VPN, some via remote access (client-based) VPN. So there is no problem with ones that have local RODC or connecting to HQ DCs via VPN router. But how about small branches? We don't really want to set up a machine there, neither we want to invest into Windows Server licenses or fancy network equipment. Also, the problem is that we cannot access HQ DCs via VPN because we are not logged in and connected to HQ internal network yet, so DCs aren't reachable. What is typically done in that situation if it is needed to have central management over policies on those PCs? Or is it better to let 'em loose and use local policies and accounts in this situation?

  Read the article

• Managing rolling deployments in the cloud

  - by Josh Nankin

  Recently I've been experimenting with various cloud management tools like RightScale, Scalr, custom scripts for managing a variety of servers, each hosting several roles (app, db, load balancer, job queues, etc). The one thing I find lacking in most solutions is a way to do rolling deployments, i.e. running deployments sequentially across a number of servers with the same role. For instance, I dont want to build all of my webservers at the same time, as that will almost definitely result in some down time or 500s for my customers. I'd rather have one or two servers build at a time, while other servers are still available to handle requests. The other alternative is obviously to launch new servers that automatically update themselves on boot, but this isn't as cost effective, and most likely requires more time for the build to complete (it's faster to build on an existing server than to launch a new server and kill old ones). We've all heard of the big companies having the famous "push to build" button (companies like Twilio, Etsy, etc.) but it seems that they all have custom implementations of this. I'm not talking about a simple ssh-loop, clusterssh, or even an mcollective - I preferably want something with a nice simple interface that allows me to specify something like a RightScript or a Scalr script to run on a set of servers with a specific role, and it builds them sequentially. Does any one know of easy ways to get this done, or is this a candidate for a new open source project?

  Read the article

• Network connection keeps dropping - bad hardware?

  - by Bill Sambrone

  Hello all, I've into a bit of a wall with a client of mine. In an office of 20 people, he is the only one who experiences broken connections to his mapped network drives. I have everyone set up with about 6 mapped drives, all pointing to the same server (no DFS), and everyone else can access them lightning fast. The environment consists of a mix of Windows 7 and XP machines, all 32-bit. The server holding the data everyone is mapping to is running on Server 2008 R2, and is a domain controller. We recently swapped out their old 10/100 switch for a shiny new Dell PowerConnect gigabit switch. We have also replaced an old dying Sonicwall with a shiny new one. Everything is running on an ESX host except for the DC, where everyone is getting data from. In my client's office, we have done the following: Swapped out his computer (Win7 and XP box) Swapped out the desktop switch in his office Removed the desktop switch in his office Changed out the network cable going to the wall Ran 'net config server /autodisconnect:-1' on the server Disabled remote differential compression on his current Win7 box When we swapped out his network cable, everything seemed fine for about 4 days. Normally I would get a phone call a couple times per day letting me know that Outlook has crashed (there is a 9GB PST living on the server he is always connected to), or that his software he is running from his L drive has crashed. I almost thought I had this solved, but after we rebooted the DC the other night he all of a sudden couldn't stay connected to his mapped network drives for more than 10 minutes. When I ran 'net use' from the command prompt, it listed all the network drives where were randomly in a state of 'OK', 'Disconnected', or 'Reconnecting'. What else should I try? Maybe there is bad wiring in the wall, patch panel, or a bad port in the new switch I have in the server room?

  Read the article

• best practices for setting up a new windows 2008 R2 server with ec2 AWS

  - by Alex

  Can someone comment what they would add to the following list of SOP in terms of best practices? This is being set up on AWS, and then after further testing, back in our datacenter. Standard Operation Procedure (SOP): Installation Part: 2 - Installation of Software Components in Windows 2008 R2 (Updated). Step: 1 Logon to the host through Remote Desktop. Strp: 2 Open Server Manager - Server Roles - Install Web Server IIS 7.5 with compatible of IIS 6 features and Management compatibility mode. Step: 3 Open IE/Mozilla to Download the below listed software's and save all installation files to folder called "AWS Server Install Files" for future reference.. Net Framework 2.0 (Download that from internet) Crystal reports for .Net Framework 2.0 (x64) (Download that from internet) SQL Server 2005 (AWS Image) Step: 4 Once all software's saved on local drive, then Install it one by one. Step: 5 Navigate to Desktop folder to install the below listed softwares. Microsoft Asp.net 2.0 AjaxExtention 1.0 (placed on Desktop \Softwares) WebEx recorder. (placed on Desktop \Softwares) Winrar(placed on Desktop \Softwares) Step: 6 Make sure all the software are working fine. Step: 7 Inspect the server once entirely. Step: 8 Logoff & Stop the Instance.

  Read the article

• Merely installing PHP5 causes my AWS Ubuntu server to die minutes later from a massive CPU spike

  - by Mark Amery

  I have an AWS server with Ubuntu 11.04 as the OS that is running an Apache2 webserver (incidentally Python-based and using Django). We recently needed to add support for php5 to let us use a third party PHP library (incidentally for serving minified versions of js and css files). However, for no reason any of us can discern, if we simply run sudo apt-get install php5 on the server, then the install appears to finish successfully but, without us taking any further action (including not yet running sudo apt-get install libapache2-mod-php5, which I think would be the next step for us if everything worked), or actually running any PHP scripts on the server, a few minutes later the server becomes impossible to connect to, and looking at the 'Monitoring' tab for the server in the EC2 Management Console reveals that a while after the installation, CPU usage spikes to 100% and stays there permanently (until we reboot the server from the AWS Console). After rebooting, the server also reliably dies within a few (between 0 and 10) minutes. We restored the server to a pre-PHP state from an AMI Image, observed that it was stable, and then tried installing PHP5 again and observed the server die in exactly the same way, so we're pretty much certain that installing PHP5 is what causes the symptoms. What on earth could be causing this behaviour, and how can we get PHP installed on the server without it dying?

  Read the article

• VPN into multiple LAN Subnets

  - by Rain

  I need to figure out a way to allow access to two LAN subnets on a SonicWall NSA 220 through the built-in SonicWall GlobalVPN server. I've Googled and tried everything I can think of, but nothing has worked. The SonicWall NSA management web interface is also very unorganized; I'm probably missing something simple/obvious. There are two networks, called Network A and Network B for simplicity, with two different subnets. A SonicWall NSA 220 is the router/firewall/DHCP Server for Network A, which is plugged into the X2 port. Some other router is the router/firewall/DHCP server for Network B. Both of these networks need to be managed through a VPN connection. I setup the X3 interface on the SonicWall to have a static IP in the Network B subnet and plugged it in. Network A and Network B should not be able to access each other, which appears the be the default configuration. I then configured and enabled VPN. The SonicWall currently has the X1 interface setup with a subnet of 192.168.1.0/24 with a DHCP Server enabled, although it is not plugged in. When I VPN into the SonicWall, I get an IP address supplied by the DHCP Server on the X1 interface and I can access Network A remotely although I do not have access to Network B. How can I allow access to both Network A and Network B to VPN clients although keep devices on Network B from accessing Network A and vice-versa. Is there some way to create a VPN-only subnet (something like 10.100.0.0/24) on the SonicWall that can access Network A and Network B without changing the current network configuration or allowing devices on both netorks "see" each other? How would I go about setting this up? Diagram of the network: (Hopefully this kind of helps) WAN1 WAN2 | | [ SonicWall NSA 220 ]-(X3)-----------------[ Router 2 ] | | (X2) 192.168.2.0/24 10.1.1.0/24 Any help would be greatly appriciated!

  Read the article

• Did my registrar screw up or is this how name server propagation works?

  - by Brad

  So my company has a number of domains with a large registrar that shall go unnamed. We are making some changes to our DNS infrastructure and the first of those is we are moving our secondary DNS from one server on site to four servers offsite. So we updated the name servers for each domain at the registrar by removing the entry for the old secondary name server and adding the four new ones. I monitored the old secondary server for requests and when I saw no new requests had been made for 24 hours I shut it down. That was this morning. I assumed at this point everything was good. Unfortunately this was my mistake. I should have gone and made sure name servers at large were returning the correct NS records. So this afternoon we were performing maintenance on our primary DNS server and we shut it down. This is when I started getting alerts from our external monitoring. I checked and sure enough, the DNS server used there reported the only NS record for our primary domain was the primary name server. The new secondary servers were not listed and neither was the old secondary. Is it unreasonable of me to have assumed that because the update was from ns1.mydomain.com ns2.mydomain.com to ns1.mydomain.com ns1.backupdns.com ns2.backupdns.com ns3.backupdns.com ns4.backupdns.com in one step at the registrar that there should be no intermediate state where the only NS record was for ns1.mydomain.com? Going forward to be safe obviously I will always leave the old name servers alone until after I'm 100% sure the new ones have propagated and only then remove the old name servers from the registrar. However, I'd still like to know if my registrar screwed up or if my expectation was unreasonable.

  Read the article

• Why does my PC successfully boot only when unplugged for more than a few minutes?

  - by philg

  I have an HP Pavilion Elite desktop computer, model HPE-490t. I like it because it didn’t cost too much, boots itself from an SSD, came with 16 GB of RAM, and has 6 CPU cores for editing video and camera RAW images. It has one behavioral quirk that I cannot explain, however. The recent power interruptions here in the Northeast got the machine into a state where it could not be restarted. It would power up for a second or two, shut down, and then power up again, never being able to get to the point of showing anything on the monitor. I unplugged it for about 10 seconds and plugged it back in. Same behavior (fails to boot). I unplugged it and walked away for an hour, then plugged it back in and it worked perfectly! I think something similar happened after installing a second hard disk drive into this machine. So the question is why does the computer behave differently depending on how long it has been unplugged? Where is energy stored that affects the machine’s ability to boot? Capacitors in the power supply? Battery on the motherboard (there is one for the clock, but that wouldn’t be exhausted by being unplugged for an hour, I don’t think)?

  Read the article

< Previous Page | 700 701 702 703 704 705 706 707 708 709 710 711  | Next Page >