Search Results

Search found 21319 results on 853 pages for 'state management'.

Page 705/853 | < Previous Page | 701 702 703 704 705 706 707 708 709 710 711 712  | Next Page >

• Merely installing PHP5 causes my AWS Ubuntu server to die minutes later from a massive CPU spike

  - by Mark Amery

  I have an AWS server with Ubuntu 11.04 as the OS that is running an Apache2 webserver (incidentally Python-based and using Django). We recently needed to add support for php5 to let us use a third party PHP library (incidentally for serving minified versions of js and css files). However, for no reason any of us can discern, if we simply run sudo apt-get install php5 on the server, then the install appears to finish successfully but, without us taking any further action (including not yet running sudo apt-get install libapache2-mod-php5, which I think would be the next step for us if everything worked), or actually running any PHP scripts on the server, a few minutes later the server becomes impossible to connect to, and looking at the 'Monitoring' tab for the server in the EC2 Management Console reveals that a while after the installation, CPU usage spikes to 100% and stays there permanently (until we reboot the server from the AWS Console). After rebooting, the server also reliably dies within a few (between 0 and 10) minutes. We restored the server to a pre-PHP state from an AMI Image, observed that it was stable, and then tried installing PHP5 again and observed the server die in exactly the same way, so we're pretty much certain that installing PHP5 is what causes the symptoms. What on earth could be causing this behaviour, and how can we get PHP installed on the server without it dying?

  Read the article

• VPN into multiple LAN Subnets

  - by Rain

  I need to figure out a way to allow access to two LAN subnets on a SonicWall NSA 220 through the built-in SonicWall GlobalVPN server. I've Googled and tried everything I can think of, but nothing has worked. The SonicWall NSA management web interface is also very unorganized; I'm probably missing something simple/obvious. There are two networks, called Network A and Network B for simplicity, with two different subnets. A SonicWall NSA 220 is the router/firewall/DHCP Server for Network A, which is plugged into the X2 port. Some other router is the router/firewall/DHCP server for Network B. Both of these networks need to be managed through a VPN connection. I setup the X3 interface on the SonicWall to have a static IP in the Network B subnet and plugged it in. Network A and Network B should not be able to access each other, which appears the be the default configuration. I then configured and enabled VPN. The SonicWall currently has the X1 interface setup with a subnet of 192.168.1.0/24 with a DHCP Server enabled, although it is not plugged in. When I VPN into the SonicWall, I get an IP address supplied by the DHCP Server on the X1 interface and I can access Network A remotely although I do not have access to Network B. How can I allow access to both Network A and Network B to VPN clients although keep devices on Network B from accessing Network A and vice-versa. Is there some way to create a VPN-only subnet (something like 10.100.0.0/24) on the SonicWall that can access Network A and Network B without changing the current network configuration or allowing devices on both netorks "see" each other? How would I go about setting this up? Diagram of the network: (Hopefully this kind of helps) WAN1 WAN2 | | [ SonicWall NSA 220 ]-(X3)-----------------[ Router 2 ] | | (X2) 192.168.2.0/24 10.1.1.0/24 Any help would be greatly appriciated!

  Read the article

• Using udev to create a character device based on a driver being loaded

  - by SteveCB

  I'm in the process of setting up RAID monitoring for a number of Dell servers that use the PERC 6i integrated card. We're using Nagios at present and the check_megasasctl plugin seems to fit the bill. However, the plugin relies upon the existence of: /dev/megaraid_sas_ioctl_node This device node doesn't exist by default, you have to create it by hand using something like: mknod /dev/megaraid_sas_ioctl_node c 253 0 Now, to make the existence of this device node persistent across reboots, I thought I could write a udev rule, but as usual, I'm missing something. I thought I could create a file such as /etc/udev/rules.d/10-local/rules that contained: DRIVER=="megasas" NAME="megaraid_sas_ioctl_node" MODE="0600" But this doesn't work - no device node after a reboot. Dmesg output indicates the megasas driver is loaded and functional: megasas: 00.00.04.01-RH1 Thu July 10 09:41:51 PST 2008 megasas: 0x1000:0x0060:0x1028:0x1f0c: bus 1:slot 0:func 0 megasas: FW now in Ready state Further, I don't see any means to instruct udev on which type of device node to create: character or block. I suspect I'm failing to understand exactly how udev is meant to work. I realise I could just cheat and run MegaCLI in /etc/rc.local, redirecting output to /dev/null; it creates the megaraid_sas_ioctl_node device node as part of its execution. I just thought using udev rules would be a) cleaner and b) a useful learning exercise. Perhaps I should just dump the above mknod command in /etc/rc.local... So how do I get udev to create the /dev/megaraid_sas_ioctl_node device node based on the presence of the megasas driver? Cheers Steve

  Read the article

• then an error occurred during the login process - Connection Error 233

  - by scott brunner

  We have SQL Server 2008 installed on 64Bit Windows Server 2003. When we try connect to the local SQL Server using SQL Server Management Studio at the console, we get the error: A connection was successfully established with the server, but then an error occurred during the login process. provider: Shared Memory Provider, error: 0 - No process is on the other end of the pipe. When we try TCP from same local SSMS to local server, we get the same error but intead of the pipe message its something like "connection forcibly closed". Now, here is the strange part - we CAN connect to this SQL Server from any other machine on the network using SSMS. - AND - WE CAN'T connect to ANY SQL Server from the problem server. So it seems the SQL Server instance is fine and accepting remote connections. However, the SSMS on that machine will not connect to any SQL Server even remotely. When we try an ADO.NET connection from C# remotely we can connect, run that same code on the console of the trouble server and we get the same errors. How can this be solved?

  Read the article

• Outlook signature distribution tools ?

  - by HannesFostie

  Hi We are soon changing our corporate identity, and as such we will need to change our outlook signatures. However, being some 125 people, my colleague sysadmin and I don't want to go around changing these manually, and are thus looking for a good way to do this fully automated. Most of our desktops are XP, with the exceptional few running Win7. Most run Outlook 2007, some run 2003. Our environment is AD-centered, and most of the information will come from AD (telephone number, title, ...). The biggest problem I can see so far is that because we are bilingual (Dutch and French), there will be 2 versions of the signature, depending on what the person has as main language. People currently do not have anything in AD to distinguish this, but we could create a group for it, or perhaps add some sort of attribute. A cheap if not free tool would be great. eMailSignature could probably do most, if not all, of this for us but it's a rather expensive tool costing some 1250 euro. We just want to distribute the signatures, actual "management" is less important as job titles don't change all that much. Any tips are welcome!

  Read the article

• Can I format a usb stick on windows xp, in HFS+ format, and make the usb stick mac os x bootable?

  - by user717236

  My Intel Mac OS X computer is corrupt and I feel, at this point, I need to perform a fresh install of the OS. It consistently and automatically logs out, right after I log in. I tried logging in as the root. I tried safe boot and it wouldn't load. Anyway, the point is I want put the Mac OS X installer on a USB thumb drive and have it boot up on the Intel Mac OS X computer. Unfortunately, the computer is inaccessible, as I mentioned above. So, I have a Windows XP machine that I'm using and attempting to create a bootable USB thumb drive that's compatible with Mac OS X. I have tried transmac, macdrive, and paradox for windows -- all of which proved unable to format the usb stick in HFS+. How do I know this? Well, even though the Transmac reports that's been formatted to HFS+, Computer Management in Windows says otherwise: I even put the installer on the usb drive, after transmac reportedly formatted it properly, and the mac os x computer didn't even recognize that a USB thumb drive was inserted, via pressing the option key at boot-up time. I'm not sure what the problem is and how to actually format the drive. Can anybody offer any help? I would appreciate it. Thank you.

  Read the article

• How do I diagnose the cause of a freeze after resuming in Windows XP (SP3)?

  - by Software Monkey

  I have just built a new computer from parts. Whenever I resume from any sleep mode (S1, S3 or S4) the computer freezes within about 60 seconds of the welcome screen appearing. I have updated the BIOS and all drivers to current from the motherboard manufacturer's site. I have reset BIOS settings to default, including disabling AMD Cool n Quiet. The windows event logs are not helpful at all. Other than immediately after resuming the system is stable as long as AMD CnQ is disabled. The system is: Mobo : MSI 790GX-G65 CPU : AMD Phenom II 965 BE at 3.6 GHz Memory : Corsair DDR3 1600, at 1333 MHz and 9-9-9-21 HDDs : 1 EIDE, 2 SATA in RAID-0 DVD : 1 Card Reader: 1 multi-card reader Keyboard is attached via PS2 and mouse is USB. Any thoughts or pointers would be most welcome. EDIT: It appears that the computer may not freeze if a program is left running which puts it under significant load. I left a stress test running which keeps all cores under 85% load, and my son put the computer to sleep - while this program is running it I have been able to resume from S3 successfully 4 times, compared against about 20 tests with the computer idle which have all frozen. So this may be related to being in an idle state when it resumes.

  Read the article

• Computer crashes if left unattended AND running uTorrent, what could be?

  - by DiegoDD

  I have a weird problem in which, if I leave my computer unattended, AND I leave uTorrent open, downloading/seeding, the computer simply crashes after about 20 / 30 minutes (don't know exactly since if I leave it, and come back later, it has already restarted or has a BSOD.) If I leave the computer alone for undefined time WITHOUT uTorrent, nothing happens, and if I am constantly using the computer while using uTorrent, no problem either (I could be using it all day with uT open and it doesn't crash). So what could it be that the combination of those cases makes the computer crash? I have already checked the power management so the computer never enters stand by mode, sleep, hibernate, etc. (the only thing I do is turn off the display). A first guess is that maybe one of my external hard drives DO sleep or enters in a "low power" mode or something if I don't use the PC. but since uT is running MAYBE tries to use that drive, and makes it crash. Could that be possible? How to know for sure if the external drive does that, and to prevent it from doing so. Any more ideas of what may be causing that? Specs: Windows 7 Pro, 64-bit, 2 GB RAM. Latest version of uTorrent (although it has been happening for a while now). UPDATE: i just found out that uTorrent has Disk cache options ( preferences - advanced - disk cache ). I have no idea if that may be causing problems with my external drive, hence causing the crash.

  Read the article

• Regarding partitions for dual-booting Ubuntu with pre-existing Windows 7

  - by Shasteriskt

  I have zero actual experience with configuring disk partitions and the stuff I have read for the past few hours have been confusing me a bit, so please bear with me. First of all, I'd like to explain what I'm setting to achieve: Windows 7 with: C:\ Windows 7 (pre-existing installation) D:\ Data (Already exists and has files already) Ubuntu 11 - Does not exist yet, but I already have a LiveCD in hand. \root directory for Ubuntu \home on its own partition I plan \swap on its own partition with around 8GB Here is the current situation: I have a single 500 GB hard-disk with Windows 7 x64 installed, and the current partition schemes is as follows: System Reserved: 100 MB (Primary, Active) C: 100 GB - Where Windows 7 is installed (Primary) D: 365 GB - Where my files are located, LOTS of free space (Primary) Now, I would like to shrink my D: drive and create around 40 GB of unallocated disk space for the Ubuntu installation, but here what's confusing me a bit: I'm thinking I would create an extended partition and subdivide it into 3 logical partitions for the Ubuntu setup I had in mind. (If you think my setup is a bad idea, please let me know & why. I also hope you can suggest a better one...) I am aware that I can only have up to 4 primary partitions, or 3 primary partitions with 1 extended parition max. Now, does the System Recovery portion count as one primary partition? I'm really new to these things and it is totally unclear to me. In shrinking my D: drive using Windows 7's Disk Management tool, I would get an unallocated free space which I don't know how to make an extended partition from. It seems like I can only create a primary partition from it, not an extended one. How do I go about it? (I'd also like to note, if it is of any importance, that I am trying to avoid using the option to install Ubuntu alongside Windows, and much rather prefer using the custom install where I can specify which drives I wish to use and stuff. Somehow I feel its safer that way.)

  Read the article

• Sun Power Button Won't Shut Down System

  - by user36680

  Background: We are running NIS and have NFS mounts from a Solaris 10 workstation to a Solaris 8 server. If the workstation loses its network connection for some reason, when I look at the workstation's console I see repeated messages of the form: <date> <time> <hostname> ypbind[<pid>]: NIS server not responding for domain "<domain>"; still trying. If I try to login at the console as a user, it won't work because it can't authenticate my account through NIS. Also, it won't return to a login prompt again, so I can't log in as root. If I press the power button (don't hold it in) on the workstation, I see: <date> <time> <hostname> power: WARNING: Power off requested from power button or SC, powering down the system! Shutdown started. <date> <time> Changing to init state 5 - please wait. <date> <time+2 minutes> <hostname> power: WARNING: Failed to shut down the system! And continue to see messages of the form: <date> <time> <hostname> ypbind[<pid>]: NIS server not responding for domain "<domain>"; still trying. So, the questions are How do I make NIS stop trying (because I know it will fail)? Why won't it shut down?

  Read the article

• Completed downloads freeze Windows

  - by Ben Hooper

  The Issue Shortly after a file download via Google Chrome for Windows completes, the download will get stuck on "0 seconds left" and all other programs (except Google Chrome, for some reason, but browsing will not work) completely freezes into Windows' infamous "Not Responding" state, affecting Explorer particularly badly. Eventually, the programs will recover themselves but they will recover significantly faster if you cancel the file download, relative to how quickly you react. Performing the exact same operation immediately after cancelling the download usually works without issue. This issue occurs when with any file type (.ZIP, .MSI, .MSG, .PNG, .URL, etc) of any size from any source (Dropbox, SourceForge, Imgur, even tiny and locally-generated BLObs created by my own Chrome extension, etc) to any location.   Potential Causes As this issue is so inconsistent, I haven't been able to prove whether the issue is Chrome-specific or being caused by my system or my Chrome configuration but it's happening on both my work and home PCs. I originally suspected that this issue was being caused by security software scanning completed downloads for threats but I'm not as confident in that theory anymore as the issue persisted even after changing my security software from ESET NOD32 and Malwarebytes Anti-Malware Pro to ESET Endpoint to Microsoft Security Essentials.   System Information (of both PCs) Windows version: 7 Service Pack 1 64-bit Google Chrome version: 30.0.1599.101 (but has been happening for a long time)   Screenshots

  Read the article

• DPMS does not work: the monitor is not switched off

  - by bortzmeyer

  I have a monitor which was properly switched off by my Debian PC when unused. I attached it to another machine and, this times, it is never switched off. In /etc/X11/xorg.conf, I have: Section "Monitor" Identifier "Generic Monitor" Option "DPMS" It is recognized when X11 starts: (II) Loading extension DPMS ... (II) VESA(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display ... (**) Option "dpms" (**) VESA(0): DPMS enabled The operating system is Debian stable "lenny". The graphics card is: 00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrate d Graphics Controller (rev 02) (prog-if 00 [VGA controller]) Subsystem: Hewlett-Packard Company Device 2a6f Flags: bus master, fast devsel, latency 0, IRQ 5 Memory at fe900000 (32-bit, non-prefetchable) [size=512K] I/O ports at b080 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at fe800000 (32-bit, non-prefetchable) [size=1M] Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-Capabilities: [d0] Power Management version 2 X11 is: X.Org X Server 1.4.2 Release Date: 11 June 2008 X Protocol Version 11, Revision 0 Build Operating System: Linux Debian (xorg-server 2:1.4.2-10.lenny2) Current Operating System: Linux ludwigVII 2.6.26-2-686 #1 SMP Sun Jun 21 04:57:3 8 UTC 2009 i686 Build Date: 08 June 2009 09:12:57AM

  Read the article

• Keepalived for more than 20 virtual addresses

  - by cvaldemar

  I have set up keepalived on two Debian machines for high availability, but I've run into the maximum number of virtual IP's I can assign to my vrrp_instance. How would I go about configuring and failing over 20+ virtual IP's? This is the, very simple, setup: LB01: 10.200.85.1 LB02: 10.200.85.2 Virtual IPs: 10.200.85.100 - 10.200.85.200 Each machine is also running Apache (later Nginx) binding on the virtual IPs for SSL client certificate termination and proxying to backend webservers. The reason I need so many VIP's is the inability to use VirtualHost on HTTPS. This is my keepalived.conf: vrrp_script chk_apache2 { script "killall -0 apache2" interval 2 weight 2 } vrrp_instance VI_1 { interface eth0 state MASTER virtual_router_id 51 priority 101 virtual_ipaddress { 10.200.85.100 . . all the way to . 10.200.85.200 } An identical configuration is on the BACKUP machine, and it's working fine, but only up to the 20th IP. I have found a HOWTO discussing this problem. Basically, they suggest having just one VIP and routing all traffic "via" this one IP, and "all will be well". Is this a good approach? I'm running pfSense firewalls in front of the machines. Quote from the above link: ip route add $VNET/N via $VIP or route add $VNET netmask w.x.y.z gw $VIP Thanks in advance. EDIT: @David Schwartz said it would make sense to add a route, so I tried adding a static route to the pfSense firewall, but that didn't work as I expected it would. pfSense route: Interface: LAN Destination network: 10.200.85.200/32 (virtual IP) Gateway: 10.200.85.100 (floating virtual IP) Description: Route to VIP .100 I also made sure I had packet forwarding enabled on my hosts: $ cat /etc/sysctl.conf net.ipv4.ip_forward=1 net.ipv4.ip_nonlocal_bind=1 Am I doing this wrong? I also removed all VIPs from the keepalived.conf so it only fails over 10.200.85.100.

  Read the article

• why Thinkpad T410s intermittent keyboard death?

  - by patrickmdnet

  I have a Thinkpad T410s running Windows 7 64-bit. I have had it for three months. It has the latest BIOS (1.41) and trackpad drivers. In the last week I have started to notice that the keyboard intermittently stops working. Specifically, keystrokes have no effect, including Fn-F12 (shutdown) and Ctrl-Alt-Del. The LED on the capslock key does not turn on or off. Whatever state the lighted keys (e.g. mute) were in remains. The trackpad and trackpoint work properly, and I can close apps and properly shut down the machine. When I attach a USB keyboard it is recognized, but no keys work. If I run the Lenovo keyboard test, all the keys register properly and the caps lock light works again. When I quit the test app, the caps lock light stops working. If I hit Fn-F12 while the keyboard test is running, it goes into hibernation. When the machine comes back from hibernation, once I exit the keyboard test I again cannot do any input on the keyboard. I'm pretty convinced there is a software or driver problem. I never saw this the first three months I had the laptop. I do not recall installing anything recently. I am sure I've received some Windows security updates. I tried using wired networking instead of wireless - no difference. There doesn't appear to be any inciting event; it usually happens when I am working over ssh. I switched from rxvt+ssh to Putty and the problem still occurs. Any ideas?

  Read the article

• Can't connect to Server Manager from Windows 7

  - by SAdmin317

  I have a Windows 7 Pro 64bit with SP1 desktop that has RSAT tools installed. I opened Server Manager and can't connect to the server (Server 2008 R2 core). I followed the guide to enable everything on the server, added a registry key to enable read-only on the device manager as well. On the Windows 7 PC I turned on winrm, did the quick config, and added the server IP and name as trusted hosts. I still get an error when connecting. "Connecting to the remote server failed with the following error message: The WinRM client cannot process the requests. If the authentication scheme is different from Kerberos, or if the client computer is not joined to a domain, then HTTPS transport must be used or the destination machine must be added to the TrustedHosts configuration setting...." I also added the name of the server to the windows 7 /etc/hosts file. Ping the server name translates to the IP of the server. Also opened up the firewall for "Remote Volume Management" Both machines are on the same Workgroup, using the same Administrator account, with the same password. Any help appreciated.

  Read the article

• Administrative shares in Windows 7 Pro not visible

  - by Chris Tybur

  My desktop machine has a clean install of Windows 7 Professional. For some reason the standard administrative shares Admin$, C$, D$, etc are not visible, either in Computer Management - Shared Folders - Shares or via net share. I also have a laptop with a clean install of Windows 7 Professional, and I can see the admin shares in both places. As such, I can map to \\laptop\c$ from the desktop, but I can't map to \\desktop\c$ from the laptop. I pretty much took the defaults during the Windows 7 installations. I've tried adding LocalAccountTokenFilterPolicy to the registry on the desktop, but that didn't work. On the desktop I've also disabled UAC, turned off Windows firewall, removed it from a homegroup, made sure file and printer sharing is turned on, but nothing has worked. There is some subtle difference between the two machines that I can't seem to find. I'm logging into both machines using a local account that is in the Administrators group. Both accounts have the same name and password. I really don't want to have to create a new share for the desktop's C drive, especially since C$ is visible and working on the laptop and therefore I should be able to make it work on the desktop. Any idea why the admin shares would work on one machine and not another? Or why LocalAccountTokenFilterPolicy would fail?

  Read the article

• Extremely Weird Computer Problem

  - by waiwai933

  Well, having worked with computers a long time, I thought I had seen everything that could go wrong with a computer. Today, I learned that I was wrong. My Mac has been behaving extremely weirdly. While the keyboard is fine, the mouse holds extremely weird behavior. It will open apps from the Dock, but not open documents from a Stack. The top menu bar will work, but only after I restart Finder. I am unable to close most windows, except with Cmd+Q. Clicking on a link in Safari, for some reason, opens it in a new tab. I can not select checkboxes, but I know a click is going through because you can see a quick indent in the check box, before it reverts to the unchecked state. I've restarted my computer, as well. I don't see a virus when looking through top, but I guess it could be subverting top. Does anyone have an idea what is going on?

  Read the article

• External SATA drive does not work without the optional USB cable *also* connected

  - by Software Monkey

  I have Vantec NST-260SU external eSATA/USB drive enclosure (which came with an optional separate power supply) connected to a relatively new Windows 7 computer. The drive should work as a SATA drive with either the separate power supply or using a USB cable solely for power. I would prefer to use the external power supply because I have used all my rear USB ports. Now, if I connect both the eSATA and USB cable, then: The drive shows in the BIOS list of AHCI drives (and not in the list of attached USB devices). Everything I can see about it in Computer Management seems to show it as a SATA driver (for example, it shows as "Location 0 (Channel 5, Target 0, Lun 0)" like my other SATA drives (and not "on USB Mass Storage Device" like my USB flash-drives). It seems very fast, very much faster than my USB flash drives. However, if I disconnect the USB cable and attach the power adapter instead, the drive does not show in the BIOS list and cannot be seen by Windows. The power LED on the enclosure is lit, and the drive enclosure becomes warm after running for a bit, so I am sure it is receiving power. Does anyone know if this device requires both the USB and eSATA cable, and if so, why? Or is there possibly something I need to do to reset the enclosure to not need the USB - the install instructions are pretty clear that you must connect the SATA cable before connecting the USB cable in order for the drive to function as SATA, which I am sure I did. PS: I have reviewed the small manual which came with it, which has not been of help.

  Read the article

• Vista won't boot. BSOD: Page fault in nonpaged area

  - by user31576

  Here's the story: I let Windows Update do the updates it wanted to do, then rebooted the computer. The updating process was taking time so I went away. When I came back, my computer was rebooting. It got as far as the Windows logo with the laoding bar. BSOD'd. Rebooted. And I'm stuck in this loop ever since. Looked up on the net, the "Page fault in nonpaged area" seems to be linked to faulty RAM or drivers. So I ran a memory test, it found no error. When I try in safe mode (with promt) I can see a list of drivers being loaded, then I get the same BSOD. I tried to repair using the Vista DVD, it says "nothing to repair". I tried to restore to a previous state, it says "no restore point found". So, my guess is, it's got something to do with the drivers. How can I identify the one causing the BSOD? If you have any other leads, What can I do? By the way, I'm writing from this very computer, running a linux distro I installed after the BSOD loop started. So i guess it's not an hardware issue. I have backed up important data, and will format and reinstall Windows if I must. But I'd like to avoid that. Thanks in advance for any help you can give me.

  Read the article

• Is there a better way to do bonded vlan tagged interfaces with XEN

  - by AJ01

  We have a number of XEN servers all running CentOS or RHEL. The VM's that they run are all required to be on their own VLAN for no other reason than the customer expects them to be. Long story short however, I can't change this right now. We are also required to have bonding enabled on the interfaces. So to accommodat this we enslave eth1 and eth2 to bond0. We then create a seperate interface called bond0.VLANID where VLANID corresponds to the correct vlan; eg ifcfg-bond0.204 DEVICE=bond0.204 BOOTPROTO=static ONBOOT=yes VLAN=yes BRIDGE=xenvlan204 Bridge to XEN As you will see, we eventually have to bridge this out to XEN, and we do this by adding another interface called xenvlan204 (in this instance) which contains; ifcfg-xenvlan204 DEVICE=xenvlan204 BOOTPROTO=none ONBOOT=yes TYPE=bridge XEN Vm Config Finally in our XEN config for each VM, we add vif = [ "bridge=xenvlan204" ] This then allows the vm host to access that particular vlan The Problem We've noticed a few problems with this setup. One being that we currently create the interfaces manually. Which means if we add more vlan enabled interfaces and bridges we usually have to restart xend which is something I'm not so hot about. Also lower level staff have their heads melted by the number of interfaces and the risk of a mistake occurring is high. Secondly, it can take sometime for a host to come up if it has a number of vlan taged interfaces. Thirdly, its just not scaling well on the management aspects The Question Is there a better more flexible way to do this (in particular with Xen that ships with centos 5.3, 5.4 and 5.5 as we have to support all three) that leverages either scripting or other solutions to allow an arbitrary amount of interfaces to be created when a vm is instanced. Your advise and expertise is more that welcomed.

  Read the article

• AHCI, Windows 7 and can only boot with Windows DVD present

  - by Rob Pridham

  Foolishly, I installed Windows 7 with my new SSD set to IDE. I would like to change it to AHCI. I have done this before, with a different motherboard. What happens: I set the controller to AHCI in the BIOS; I also check correct boot order On boot, I get the 'BOOTMGR not found' error I use the Windows Recovery Console on the DVD Diskpart etc can see the disks, and bootrec claims to have rewritten the MBR/bootloader I reboot, same problem Recovery Console again and it detects a problem, fixes, reboots Recovery Console again and it detects the OS, and a problem - fixes, reboots I ignore the 'press any key to boot from DVD' prompt Windows boots fine I restart without the DVD and I'm back to square one That optional 'press a key to boot from DVD' stage is something that the recovery process introduces - normally you have to choose to boot to the DVD at the BIOS stage. You also see this when installing Windows. I suspect that whatever temporary state that is is compatible with AHCI - but not the standard it returns to. I have done the msahci/iaStorV registry hacks to no avail (this worked with the previous board). I can put it back to IDE where normal service is resumed. The board is an Asus M5A99X, the southbridge is AMD SB950, and this is Windows 7 x64. I would quite like not to have to reinstall it again. Any ideas as to what I can do as a permanent fix?

  Read the article

• How do I restore to a delta file (disk) on Vmware ESXi

  - by Oscar

  Using VMware Server ESXi (freebie version) I have a Virtual Machine (win 2k3 r2 server). When I first provisioned it I took a snapshot of it. I recently tried to clone the primary drive using my standard hardware-based method to grow a windows disk. (using knoppix, clone drive to a new drive, make it bootable, then I intended to extend the partition via diskpart from within windows). This process failed; I tried setting the cloned drive (via the vmware gui) to replace the original drive, boot and be done. This didn't work out so well. The machine never booted. I checked the boot order, the disk location and all the basics I usually do. As a failsafe, I then tried changing all the settings back so the machine would boot to the original drive and I could figure out (as I eventually did) a better way of growing the disk. However when I powered on the machine with the original drive, it reverted back to that initial snapshot I created; It lost all the changes since. I looked in the file system and found a few files, I think the keyfile here is one named "delta" and I'm assuming that's the disk I want, but I can't find a way to have the Virtual Machine actually use that drive/file. It isn't available to add when I go to add an existing drive. Do I need to somehow commit that delta to the original drive and then boot from it again? Can you point me in the right direction? I've since discovered the proper way of growing drives using "vmkfstools" but I need to get back to the original state of the machine to try this out. Any help would be greatly appreciated.

  Read the article

• Snapshotting single disk of running Hyper-V VM

  - by modelnine

  I'm currently somewhat at a loss of how to create a snapshot of a single virtual hard-disk of a running Hyper-V VM. Generally, creating a differential disk while a server is shut down is no problem (i.e., call the new-vhd cmdlet and pass a ParentPath, then update the VHD-binding of the respective VM-device), but while the host is running, all I can find is checkpointing the VM as a whole (which creates snapshots of all attached disks), and leaves the VM-state in a form which isn't easily processable by external tools (i.e., it requires reading additional meta-data from the VM). Generally, what'd I'd like to happen for a single-disk snapshot (in my understanding) is: Pause the VM Rename current disk to some other name which specifies it as a base-snapshot Create a new VHD which has the renamed VHD as parent path and is marked as "current" Swap the VHD for the VM for the snapshotted hard-disk to the newly created differential VHD Resume the VM Is there any means to do this programatically? Update: I've seen that this is actually possible with SCSI-disks, i.e. pause the VM, remove the SCSI disk, make the snapshot, reattach the SCSI disk at the same position, resume the VM. And, the VM resumes properly. But: is something similar also possible with G1 machines for the boot disk which is always IDE?

  Read the article

• NFS-shared file-system is locking up

  - by fredden

  Our NFS-shared file-system is locking up. Please feel free to ask any questions you feel relevant. :) At the time, there are a lot of processes in "disk sleep" state, and the load averages on our machines sky-rocket. The machines are responsive on SSH, but our the majority of our websites (apache+mod_php) just hang, as does our email system (exim+dovecot). Any websites which don't require write access to the file-system continue to operate. The load averages continue to rise until some kind of time-out is reached, but for at least 10-15 minutes. I've seen load averages over 800, yet the machines are still responsive for actions which don't require writing to the shared file-system. I've been investigating a variety of options, which have all turned out to be red-herrings: nagios, proftpd, bind, cron tasks. I'm seeing these messages in the file server's system log: Jul 30 09:37:17 fs0 kernel: [1810036.560046] statd: server localhost not responding, timed out Jul 30 09:37:17 fs0 kernel: [1810036.560053] nsm_mon_unmon: rpc failed, status=-5 Jul 30 09:37:17 fs0 kernel: [1810036.560064] lockd: cannot monitor node2 Jul 30 09:38:22 fs0 kernel: [1810101.384027] statd: server localhost not responding, timed out Jul 30 09:38:22 fs0 kernel: [1810101.384033] nsm_mon_unmon: rpc failed, status=-5 Jul 30 09:38:22 fs0 kernel: [1810101.384044] lockd: cannot monitor node0 Software involved: VMWare, Debian lenny (64bit), ancient Red Hat (32 bit) (version 7 I believe), Debian etch (32bit) NFS, apache2+mod_php, exim, dovecot, bind, amanda, proftpd, nagios, cacti, drbd, heartbeat, keepalived, LVS, cron, ssmtp, NIS, svn, puppet, memcache, mysql, postgres Joomla!, Magento, Typo3, Midgard, Symfony, custom php apps

  Read the article

• Hyper-V: Dedicated NIC for Guests VMs

  - by TheLizardKing

  I have two NIC cards and created a private virtual network for my virtual machines and unchecked "Allow management operating system to share this network adapter" which basically turns my Guest NIC into this sorta shell of a NIC card on the host machine and the only thing checked in it's properties is "Microsoft Virtual Network Switch Protocol" which I am fine with. Everything works and everything is connected. My issue is that for some reason my guest (Ubuntu Server with legacy network drivers) is not talking properly to my DHCP server. Specifically my DHCP server reserves the guest's IP address using it's MAC address but the guest isn't picking it up. It's picking up any old IP it can get and I can't even ping the hostname from another PC on the network but it pings fine if I use the IP. I see the guest showing up in my DHCP table but I can't get the reservation to stick. Is there some reason it's only partially communicating with my DHCP server? Pinging it's hostname on itself reveals it's using 127.0.0.1 instead of it's network IP. Is this an issue with the legacy drivers used in Hyper-V?

  Read the article

< Previous Page | 701 702 703 704 705 706 707 708 709 710 711 712  | Next Page >