Search Results

Search found 18907 results on 757 pages for 'computer history'.

Page 726/757 | < Previous Page | 722 723 724 725 726 727 728 729 730 731 732 733  | Next Page >

  • Impact of the L3 cache on performance - worth a dual-processor system?

    - by Dan Nissenbaum
    I will be purchasing a new high-end system, and I would like to have a better sense of whether a dual-processor Xeon system (I am looking at the new, high-end Xeon E5-2687W) might, realistically, provide a noticeable performance improvement due to the doubling of the L3 cache (20 MB per CPU). (This is in addition to the occasional added advantage due to the doubling of cores and RAM.) My usage scenario is, roughly, that I have many background applications running at any time - 3 or 4 data compression/backup applications, a low-impact web server, one or two virtual machines at any given time (usually fairly idle), and perhaps 20 utility programs that utilize a noticeable (but small) portion of the CPU cores. In total, when I am not actively using the computer, about 25% of the total CPU power is utilized in my current i7-970 6-core (12 thread) system. When I am doing routine work, the CPU utilization often exceeds 50%, and occasionally hits 75%-80%. The Xeon E5-2687W is not only a second-generation i7 (so should improve performance for that reason), but also has 8 cores (16 threads), rather than 6 cores. For this reason, I expect to run into the 75% CPU range even less frequently. Nonetheless, the ability to double the cores and the RAM is a consideration. However, in the end, I believe this decision comes down to whether the doubling of the L3 cache will provide a noticeable improvement. There are many benchmarks, and a lot of discussion, regarding CPU power. However, I find very little discussion of L3 cache utilization, and how increases in the L3 cache (such as doubling it with dual processors) affect performance. For example: If there are only two processes running, but each benefits from a large L3 cache (such as might be the case for background processes that frequently scan the file system), perhaps the overall system performance might noticeably improve with dual CPU's - even if only a single core is active on each CPU - due to each process having double the effective L3 cache. I am hoping that someone has a sense of the benefits of increasing (or doubling) the L3 cache size. Note: the CPU I am considering (the Xeon E5-2687W) has 20 MB L3 cache, so a system with dual CPU's would have 40 MB L3 cache.

    Read the article

  • Operative systems on SD cards

    - by HisDudeness
    I was getting some wild ideas the last days, like putting some operative systems into SD cards rather than on my hard drive. I'll go further into details now and explain what lead me to consider this probably abominable decision. I am on a laptop (that means I have a native SD-card reader) which is currently running a cross-distro setup, with a bunch of Linux systems (placed in dedicated ext4 logical partitions into a huge extended one) regulated by an unique GRUB. Since today, my laptop haven't even seen any Windows system with binoculars. I was thinking about placing all the os part of my setup into a Secure Digital to save all my 500 Gb Hard Drive for documents, music, videos and so on, and being able to just remove the SD and boot my system into another computer too, as well as having the possibility of booting other systems into mine by just plugging in another SD, without having to keep it constantly placed in my PC. Also, in the remote case in the near future I just wanted to boot Windows 8 in it, I read it causes major boot incompatibility issues with other systems by needing a digital signature in order for them to start. By having it in a removable drive, I could just get rid of it when I'm needing him and switch its card with Linux one, and so not having any obstacles to their boot. Now, my questions are: I know unlikely traditional rotating disk drives, integrated circuits ones have a limited lifespan in terms of cluster rewriting. Is it an obstacle to that kind of usage? I mean, some Ultrabooks are using SSD now, is it the same issue, or there are some differences between Solid State Drives and Secure Digitals in that sense? Maybe having them to store system files which are in fixed positions (making the even-usage of cluster technology useless) constantly being re-read and updated and similar things just gets them soon unserviceable, do it? Second question: are all motherboards and BIOSes able to boot from SDs just like they are from USB pen drives (I mean, provided card reader is USB-connected, isn't it)? Or can't bootloaders like GRUB be installed on SDs working? If they can't, is it a solution installing GRUB to MBR and making boot option pointing to SD? Will it work? Are there any other problems to installing OSs on a Secure Digital?

    Read the article

  • Cannot install grub to RAID1 (md0)

    - by Andrew Answer
    I have a RAID1 array on my Ubuntu 12.04 LTS and my /sda HDD has been replaced several days ago. I use this commands to replace: # go to superuser sudo bash # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded" # remove broken disk from RAID mdadm /dev/md0 --fail /dev/sda1 mdadm /dev/md0 --remove /dev/sda1 # see partitions fdisk -l # shutdown computer shutdown now # physically replace old disk by new # start system again # see partitions fdisk -l # copy partitions from sdb to sda sfdisk -d /dev/sdb | sfdisk /dev/sda # recreate id for sda sfdisk --change-id /dev/sda 1 fd # add sda1 to RAID mdadm /dev/md0 --add /dev/sda1 # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded, recovering" # to see status you can use cat /proc/mdstat This is the my mdadm output after sync: /dev/md0: Version : 0.90 Creation Time : Wed Feb 17 16:18:25 2010 Raid Level : raid1 Array Size : 470455360 (448.66 GiB 481.75 GB) Used Dev Size : 470455360 (448.66 GiB 481.75 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Thu Nov 1 15:19:31 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 92e6ff4e:ed3ab4bf:fee5eb6c:d9b9cb11 Events : 0.11049560 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 17 1 active sync /dev/sdb1 After bebuilding completion "fdisk -l" says what I have not valid partition table /dev/md0. This is my fdisk -l output: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00057d19 Device Boot Start End Blocks Id System /dev/sda1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sda2 940910985 976768064 17928540 5 Extended /dev/sda5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000667ca Device Boot Start End Blocks Id System /dev/sdb1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sdb2 940910985 976768064 17928540 5 Extended /dev/sdb5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/md0: 481.7 GB, 481746288640 bytes 2 heads, 4 sectors/track, 117613840 cylinders, total 940910720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table This is my grub install output: root@answe:~# grub-install /dev/sda /usr/sbin/grub-setup: warn: Attempting to install GRUB to a disk with multiple partition labels or both partition label and filesystem. This is not supported yet.. /usr/sbin/grub-setup: error: embedding is not possible, but this is required for cross-disk install. root@answe:~# grub-install /dev/sdb Installation finished. No error reported. So 1) "update-grub" find only /sda and /sdb Linux, not /md0 2) "dpkg-reconfigure grub-pc" says "GRUB failed to install the following devices /dev/md0" I cannot load my system except from /sdb1 and /sda1, but in DEGRADED mode... Anybody can resolve this issue? I have big headache with this.

    Read the article

  • How can I reverse mouse movement (X & Y axis) system-wide? (Win 7 x64)

    - by Scivitri
    Short Version I'm looking for a way to reverse the X and Y mouse axis movements. The computer is running Windows 7, x64 and Logitech SetPoint 6.32. I would like a system-level, permanent fix; such as a mouse driver modification or a registry tweak. Does anyone know of a solid way of implementing this, or how to find the registry values to change this? I'll settle quite happily for how to enable the orientation feature in SetPoint 6.32 for mice as well as trackballs. Long Version People seem never to understand why I would want this, and I commonly hear "just use the mouse right-side up!" advice. Dyslexia is not something which can be cured by "just reading things right." While I appreciate the attempts to help, I'm hoping some background may help people understand. I have a user with an unusual form of dyslexia, for whom mouse movements are backward. If she wants to move her cursor left, she will move the mouse right. If she wants the cursor to move up, she'll move the mouse down. She used to hold her mouse upside-down, which makes sophisticated clicking difficult, is terrible for ergonomics, and makes multi-button mice completely useless. In olden times, mouse drivers included an orientation feature (typically a hot-air balloon you dragged upward to set the mouse movement orientation) which could be used to set the relationship between mouse movement and cursor movement. Several years ago, mouse drivers were "improved" and this feature has since been limited to trackballs. After losing the orientation feature she went back to upside-down mousing for a bit, until finding UberOptions, a tweak for Logitech SetPoint, which would enable all features for all pointing devices. This included the orientation feature. And there was much rejoicing. Now her mouse has died, and current Logitech mice require a newer version of SetPoint for which UberOptions has not been updated. We've also seen MAF-Mouse (the developer indicated the version for 64-bit Windows does not support USB mice, yet) and Sakasa (while it works, commentary on the web indicate it tends to break randomly and often. It's also just a running program, so not system-wide.). I have seen some very sophisticated registry hacks. For example, I used to use a hack which would change the codes created by the F1-F12 keys when the F-Lock key was invented and defaulted to screwing my keyboard up. I'm hoping there's a way to flip X and Y in the registry; or some other, similar, system-level tweak out there. Another solution could be re-enabling the orientation feature for mice, as well as trackballs. It's very frustrating that input device drivers include the functionality we desperately need for an accessibilty concern, but it's been disabled in the name of making the drivers more idiot-proof.

    Read the article

  • Adaptec 5805 not recognized after reboot

    - by Rakedko ShotGuns
    After rebooting the system, the controller is not recognized. It only works if the computer is shut down and turned off. I have recently updated the firmware to "Adaptec RAID 5805 Firmware Build 18948". How do I fix the problem? Configuration summary --------------------------- 1. Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priority High Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1

    Read the article

  • Automatic layout of manual network mapping

    - by Paul
    So I have a small business network mainly consisting of two routed layer-2 domains with a total of ca. 100 devices spread over ca. 2000m² production and office spaces. Typical problems to solve using the graph would be: Over what (cable) path is a PC connected to the server? Where to expect devices connected to a switch port? I want to generate a graph of the physical network topology: Nodes are endpoint devices, switch ports, wall outlets, patch panel ports etc. Edges are cable connections. Ideally, grouping edges (or segments) that pass through the same bundle could be grouped. Also I would like to augment the graph data with automatically gathered data (monitoring state, MAC address, Switch port <- MAC entries to build up parts of the map). At the moment I use graphviz for this inside a Confluence wiki like that: layout = "neato" overlap = scale subgraph { rankdir = "TB" subgraph cluster_r1pf1 { r1pf1 [label="{ Rack 1 PF 1 | { <p1>P1 | <p2>P2 | <p3>P3} }", shape=record] } subgraph cluster_switch1 { switch1 [label="{ Rack 1 Switch 1 | { <p1> P1 | <p1> P1 | <p3> P3} }", shape=record] } r1pf1:p1 -> switch1:p1 (obviously there are dozens of entries omitted here) Problem is: I have a hard time to influence graphviz to generate a bearable layout. Edges overlap so bad that you can't read the diagram anymore. The question is: What other tools (be it interactive like Visio, Omnigraffle or I/O-oriented like graphviz) exist that would allow an easily versionable (as in: Operates on a text file) documentation that is both machine and human readable and editable? Why not OmniGraffle or Visio? Well we don't have Macs and Visio is not available at the moment. To buy it I would need good arguments. Automation would be one of that. But last time I looked, versioning Visio files or even thinking about automatic handling was a nightmare. Related: Network Mapping Tools basically asks the same with a focus on generating the complete graph automatically (but without the need to document cabling connections) Recommendations for automatic computer inventory brings up links of "all-in-one" solutions

    Read the article

  • GPU not powering on

    - by Lerp
    So I got home from work yesterday and went to turn my computer on as per usual to be greeted by this: The screens remained black, so I rebooted; I go as far as GRUB before my screens went black again. I rebooted again, they didn't turn on. I rebooted again, I got as far as the windows login screen. This time I unplugged it, opened it up and cleaned it but to no luck. The GPU was still being tempermental. I repeated the process of turning off and on several times until one time it work as normal. I happily played games for the rest of the night (5-6 hours?) thinking everything was jolly good now. Well I get home from work today and it is doing the SAME thing. Sometimes everything displays normally for a few seconds to minutes then the screens go black; then sometimes the screens don't come on at all. Summary and additional points Screens sometimes turn on before shortly turning off, sometimes they don't; I cannot seem to determine any pattern between when they do or do not turn off. The build has been working fine for about 8 months now so I know it's not hardware incompatibility. If I plug a monitor into the on board graphics I can use the PC normally (just in low graphics mode) I have two monitors and it's a case of they both turn on or not. So I think I can rule out the monitors being dead. I have tried replacing the GPU I have tried replacing the RAM I have tried flashing the CMOS I have tried cleaning the inside The GPU is a Radeon HD 7870 My questions Is my GPU dead? It's not very old and I would rather have a method of being certain it's the GPU before I fork out some money I can't really afford. I do not have a second PC here to test it in. If my GPU is dead why does it sometimes work and sometimes not? Update Okay, it was working again.. at least I thought it was. I left it running for 10-20minutes with the screens black. Turned it off and straight back on and it worked for all of 10minutes. I was then updating the post in joy thinking I could play some games for the rest of the night when BAM it went black again. So yeah, I don't know :C

    Read the article

  • "Error 1067: The process terminated unexpectedly" when trying to install MySQL on Win7 x64.

    - by Gravitas
    Hi, I've run into a brick wall trying to install MySQL v5.5 on my machine. My PC is Windows 7 x64, Enterprise edition. MySQL installs fine, but when I run the "MySQL Instance Configuration Wizard", it pauses forever on the step "Start Service" (I can let it run for 30 minutes with no response). If I go into services, I see that the "MySQL" service hasn't started, and if I try to start it, it says "Windows could not start MySQL Service on Local Computer. Error 1067: The process terminated unexpectedly." I've tried the following: Turning off firewall. Uninstalling all antivirus software. Installing / reinstalling 32-bit version of MySQL. Installing / reinstalling 64-bit version of MySQL. Uninstalling, deleting the contents of "C:\program files\MySQL" and "C:\program files (x86)\MySQL", reinstalling. Checking to see that there is no rogue services named MySQL???? (from a previous install). Checking that port 3306 is not used by an alternate program. Changing the default port that MySQL uses. Checking for "my.ini" and "my.ini.cnf" in "C:\windows" (nothing there but that can cause a problem). Running both MySQL installer, and configuration wizard, in "Adminstrator mode". Turning off UAC. Installing with defaults, not changing anything. Rebooting my machine (about 6 reboots so far). Opening up port 3306 in the firewall (both TCP and UDP, inbound and outbound). Swearing at the klutz of a programmer who designed MySQL so you can't even install it (as if that would help!) My machine is working 100% in every other way. InfiniDB (a MySQL compatible database) installs 100%, as does Visual Studio 2010, Microsoft SQL Server, etc, etc. Your advice on how to work around this? p.s. Here is the screen it got stuck on for 15 minutes until I killed the process: Update 2010-12-20 Tried MySQL v5.1, it didn't work either. Its amazing - if you type "mysqld /?", or "mysqld -help", it doesn't give you any help. And, if you try to restart the service manually, it doesn't display any error messages. Could it be any more unhelpful? Update 2010-12-21 Installed MySQL 6.0 alpha, and it worked. However, I'd rather not use an alpha release, given that the "stable" release is anything but :( Update 2010-12-21 Found http://dev.mysql.com/doc/refman/5.1/en/windows-troubleshooting.html, dealing with troubleshooting under Windows. Discovered that you can generate an error log if the service doesn't start - see here: http://dev.mysql.com/doc/refman/5.1/en/error-log.html

    Read the article

  • Domain: Netlogon event sequence

    - by Bob
    I'm getting really confused, reading tutorials from SAMBA howto, which is hell of a mess. Could you write step-by-step, what events happen upon NetLogon? Or in particular, I can't get these things: I really can't get the mechanism of action of LDAP and its role. Should I think of Active Directory LDS as of its superset? What're the other roles of AD and why this term is nearly a synonym of term "domain"? What's the role of LDAP in the remote login sequence? Does it store roaming user profiles? Does it store anything else? How it is called (are there any upper-level or lower-level services that use it in the course of NetLogon)? How do I join a domain. On the client machine I just use the Domain Controller admin credentials, but how do I prepare the Domain Controller for a new machine to join it. What's that deal of Machine trust accounts? How it is used? Suppose, I've just configured a machine to join a domain, created its machine trust, added its data to the domain controller. How would that machine find WINS server to query it for Domain Controller NetBIOS name? Does any computer name, ending with <1C type, correspond to domain controller? In what cases Kerberos and LM/NTLM are used for authentication? Where are password hashes stored in, say, Windows2000 domain controller? Right in the registry? What is SAM - is it a service, responsible for authentication and sending/storing those passwords and accompanying information, such as groups policies etc.? Who calls it? Does it use Active Directory? What's the role of NetBIOS except by name service? Can you exemplify a scenario of its usage as a "datagram distribution service for connectionless communication" or "session service for connection-oriented communication"? (quoted taken from http://en.wikipedia.org/wiki/NetBIOS_Frames_protocol description of NetBIOS roles) Thanks and sorry for many questions.

    Read the article

  • SCCM SP2 - OOB Management Certificates Problems

    - by Achinoam
    Hi experts, I have a vPro client computer with AMT 4.0. It was importeed successfully via the Import OOB Computers wizard, and after sending a "Hello- packet" it became provisioned. (The SCCM GUI displays AMT Status: Provisioned). But when I try to perform power operations on this machine, they always fail with the following lines in the log: AMT Operation Worker: Wakes up to process instruction files 7/29/2009 10:59:29 AM 2176 (0x0880) AMT Operation Worker: Wait 20 seconds... 7/29/2009 10:59:29 AM 2176 (0x0880) Auto-worker Thread Pool: Work thread 3884 started 7/29/2009 10:59:29 AM 3884 (0x0F2C) session params : https:/ / amt4.domaindemo.com:16993 , 11001 7/29/2009 10:59:29 AM 3884 (0x0F2C) ERROR: Invoke(invoke) failed: 80020009argNum = 0 7/29/2009 10:59:31 AM 3884 (0x0F2C) Description: A security error occurred 7/29/2009 10:59:31 AM 3884 (0x0F2C) Error: Failed to Invoke CIM_BootConfigSetting::ChangeBootOrder_INPUT action. 7/29/2009 10:59:31 AM 3884 (0x0F2C) AMT Operation Worker: AMT machine amt4.domaindemo.com can't be waken up. Error code: 0x80072F8F 7/29/2009 10:59:31 AM 3884 (0x0F2C) Auto-worker Thread Pool: Warning, Failed to run task this time. Will retry(1) it 7/29/2009 10:59:31 AM 3884 (0x0F2C) After investigation, I've seen that the problem occurs already on the 2nd stage of the provisioning: Start 2nd stage provision on AMT device amt4.domaindemo.com. 8/2/2009 4:55:12 PM 2944 (0x0B80) session params : https: / / amt4.domaindemo.com:16993 , 11001 8/2/2009 4:55:12 PM 2944 (0x0B80) Delete existing ACLs... 8/2/2009 4:55:12 PM 2944 (0x0B80) ERROR: Invoke(invoke) failed: 80020009argNum = 0 8/2/2009 4:55:14 PM 2944 (0x0B80) Description: A security error occurred 8/2/2009 4:55:14 PM 2944 (0x0B80) Error: Cannot Enumerate User Acl Entries. 8/2/2009 4:55:14 PM 2944 (0x0B80) Error: CSMSAMTProvTask::StartProvision Fail to call AMTWSManUtilities::DeleteACLs 8/2/2009 4:55:14 PM 2944 (0x0B80) Error: Can not finish WSMAN call with target device. 1. Check if there is a winhttp proxy to block connection. 2. Service point is trying to establish connection with wireless IP address of AMT firmware but wireless management has NOT enabled yet. AMT firmware doesn't support provision through wireless connection. 3. For greater than 3.x AMT, there is a known issue in AMT firmware that WSMAN will fail with FQDN longer than 44 bytes. (MachineId = 17) 8/2/2009 4:55:14 PM 2944 (0x0B80) STATMSG: ID=7208 SEV=E LEV=M SOURCE="SMS Server" COMP="SMS_AMT_OPERATION_MANAGER" SYS=JE-DEV-MS0 SITE=JR1 PID=1756 TID=2944 GMTDATE=Sun Aug 02 14:55:14.281 2009 ISTR0="amt4.domaindemo.com" ISTR1="amt4.domaindemo.com" ISTR2="" ISTR3="" ISTR4="" ISTR5="" ISTR6="" ISTR7="" ISTR8="" ISTR9="" NUMATTRS=0 8/2/2009 4:55:14 PM 2944 (0x0B80) This error is consistent with all the other 2nd stage provisioning tasks. (Add ACLs, Enable Web UI, etc.) I've opened the certification authority, and I see that the certificates were issued to the SCCM Site server instead of the AMT client! What could be the reason for this failure? What is the problematic definition for the certificate? Thank you in advance!!!

    Read the article

  • Radeon HD4850 serious issues when using DirectX 10

    - by ricsmania
    Hello, I have a problem with my video card. Whenever I run a DirectX 10 game, it works for a few seconds (10 or so) and then starts displaying nothing but big polygons. I have tested this with Crysis and Resident Evil 5, both have the same problems. The same games running under DirectX 9 work fine, except for some small black squares once in a while. I have the following specs: Asus P7P55D LE Intel Core i5 750 Sapphire Radeon HD4850 1GB 2x2GB Patriot Viper II Sector 5, DDR3 1600 MHz OCZ Stealth X Stream 500SXS 500W At first I thought it could be the video card overheating (it has stock cooling), but the game crashes even when it's running at 50 degrees C, and it's never been higher than 70. I also thought it could be the PSU, but as far as I know 500W is enough for this computer, especially because I haven't overclocked anything. My OS is Windows 7 X64 and I am using Catalyst 10.10, but I have also tried many older versions with no success. I don't think there is a problem with the card itself, or else it wouldn't run DirectX 9 games I believe. I have spent many hours searching for a solution but I couldn't, so any help is appreciated. Thank you. EDIT: I did some further investigation about the problem, and it seems taspeotis was right, it might be related to memory. I slightly underclocked the memory from 993 to 965 MHz and the problem went away completely. Both the black squares using DirectX 9 and the weird polygons using DirectX 10. I was using RE DirectX 10 Benchmark, as it consistently crashed around the same point, and now I can play the full benchmark with no artifacts at all. Unfortunately, the underclock has an obvious hit in performance. Although it's not critical, it's definitely noticeable. So, if the video memory test software showed no erros, but the card needs an underclock to work, what might be the problem? Temperature? Voltage? By the way, I couldn't find what the default voltage for this card is. And what is a good software to try and increase it? I tried Ati Tray Tools but it has a bug that increases the clock speed dramatically whenever I change something in the Overclock tab, so I'm afraid it might fry my card. Worst case scenario, if I don't find I solution I will try to slightly increase the GPU clock to compensate for the memory clock. Thank you again.

    Read the article

  • Why is Windows 7 announcing itself as an IPv6 router?

    - by Paul
    I have a 6in4 ipv6 connection from a linux box to a broker. I use gogoc to establish the connection to the broker, and radvd to advertise the route to clients on the network. All this appears to work, the problem is that I have a Windows 7 machine on the same network, and it is advertising itself as a ipv6 router. Which it is not. This is output from radvdump: # # radvd configuration generated by radvdump 1.8.5 # based on Router Advertisement from [snip]:ea2 # received by interface eth0 # interface eth0 { AdvSendAdvert on; # Note: {Min,Max}RtrAdvInterval cannot be obtained with radvdump AdvManagedFlag on; AdvOtherConfigFlag on; AdvReachableTime 0; AdvRetransTimer 0; AdvCurHopLimit 0; AdvDefaultLifetime 1800; AdvHomeAgentFlag off; AdvDefaultPreference medium; AdvSourceLLAddress on; AdvLinkMTU 1500; }; # End of interface definition # # radvd configuration generated by radvdump 1.8.5 # based on Router Advertisement from [snip]:1121 # received by interface eth0 # interface eth0 { AdvSendAdvert on; # Note: {Min,Max}RtrAdvInterval cannot be obtained with radvdump AdvManagedFlag off; AdvOtherConfigFlag off; AdvReachableTime 0; AdvRetransTimer 0; AdvCurHopLimit 64; AdvDefaultLifetime 1800; AdvHomeAgentFlag off; AdvDefaultPreference medium; AdvLinkMTU 1280; AdvSourceLLAddress on; prefix [snip]::/64 { AdvValidLifetime 86400; AdvPreferredLifetime 14400; AdvOnLink on; AdvAutonomous on; AdvRouterAddr off; }; # End of prefix definition }; # End of interface definition And I end up with two routes: $ ip -6 route [snip]::/64 dev eth0 proto kernel metric 256 expires 86117sec fe80::/64 dev eth0 proto kernel metric 256 default via [snip]:ea2 dev eth0 proto kernel metric 1024 expires 1492sec default via [snip]:1121 dev eth0 proto kernel metric 1024 expires 1506sec The ea2 route is to the Windows7 box. It doesn't have a router installed, and doesn't have any tun/tap interfaces. I can't see why it is doing this. I could disable ipv6 on it, but I want it to be a client, not a router. Update: The IP Helper service (Provides tunnel connectivity using IPv6 transition technologies (6to4, ISATAP, Port Proxy, and Teredo), and IP-HTTPS. If this service is stopped, the computer will not have the enhanced connectivity benefits that these technologies offer.) seems to be the culprit, as if it is stopped, I don't get the routes advertised. So my question is now more specifically "why is IP Helper announcing routes?".

    Read the article

  • DLINK WBR-1310B Wireless Router seems to hang...

    - by Ira Baxter
    I have a brand new DLINK-1310B Wireless Router (box never before opened, although I bought it at the neighborhood computer junk store). I am using it at home (and in fact am using it at this instant from a wireless laptop). When operative, I can ping it at 192.168.0.1, and I can log into it from the PC attached to it by LAN and from the wireless PC at //192.168.0.1. In the course of the day since I've installed, it seems to have locked up 3 times. Each time the symptoms are my web browser (or other IP service, e.g., POP3) stops with a "No internet connection" error. Attempts to contact the router via 192.168.0.1 get no reaction, from either the wireless laptop or from the hardwired PC sitting next to it. It doesn't respond to pings to that address either. Power cycling the router fixes it. I've seen discussion in other questions about aging cheap electronics. Its too new to be aged. Anybody else seen this behavior with a DLINK-1310? Or do I just need to exchange it for another and try again? (I hate rolling dice, I bought the DLINK because a previous Linksys died of apparant heating problems, how many do I have to cycle through before I get something that works and is long-term stable?). Remarkably, nobody talks about how much software is in a router. Is the stuff just buggy? EDIT: Happened again, while I was working on the wireless Vista laptop. (Seems like once an hour?) I was a little more careful this time. The wireless laptop can ping it. It can't get the login screen. I visited the LAN-connected PC (takes me a minute to walk from the laptop to the PC at the other end of the house), and attempted to visit a random web page. Surprise, that worked! And, now, after a minute walking back to the laptop, I can reconnect the wireless laptop, and get to the login page from it. Strange the time/date has been reset back to 2002. (I'll swear I set it and saved the system configuration after updating the firmware; it made me redo every other bit of reconfiguration again). Is there something funny about wireless leases expiring? The router says the leases it is handing out are good for 180 minutes, and the delay-to-inaccessible was only about an hour. The DSL connection seems to have a 10 minute lease.

    Read the article

  • Unable to telnet out on port 25 on windows server 2008

    - by NickGPS
    Hi All, I just setup a Windows 2008 R2 server and am trying to get a basic mail server up and running so that I can send emails from my applications. I setup a virtual SMTP server in IIS6 and tried doing a local telnet to port 25, which seemed to work fine. There were no errors during this stage and I can see the mail message appear in the Queue folder. The problem is that mail never leaves the Queue folder. I then tried to telnet to a remote mail server on port 25 but couldn't connect:- telnet 209.85.227.27 25 Could not open connection to the host, on port 25: Connection failed) I checked my firewall and there is a default setting to allow all outgoing TCP traffic with no restriction. I even setup a specific rule for outgoing port 25 traffic but to no avail. I then ran a SmtpDiag.exe command .\SmtpDiag.exe [email protected] [email protected] and received the following output Searching for Exchange external DNS settings. Computer name is WIN-SERVERNAME. Failed to connect to the domain controller. Error: 8007054b Checking SOA for gmail.com. Checking external DNS servers. Checking internal DNS servers. SOA serial number match: Passed. Checking local domain records. Checking MX records using TCP: gmail.com. Checking MX records using UDP: gmail.com. Both TCP and UDP queries succeeded. Local DNS test passed. Checking remote domain records. Checking MX records using TCP: gmail.com. Checking MX records using UDP: gmail.com. Both TCP and UDP queries succeeded. Remote DNS test passed. Checking MX servers listed for [email protected]. Connecting to gmail-smtp-in.l.google.com [209.85.227.27] on port 25. Connecting to the server failed. Error: 10060 Failed to submit mail to gmail-smtp-in.l.google.com. Is there any other diagnostics I can do to figure out if it's my firewall or something else? I have removed antivirus to make sure that it wasn't causing the problem. Any ideas would be much appreciated.

    Read the article

  • Poor performance of single processor 32bit Windows XP xompared SMP in VBA+Excel

    - by Adam Ryczkowski
    Welcome! On many computers I experienced poor performance of 32 bit guests running on 64 bit Linux host (I used only the Debian family). At last I managed to collect benchmark data. I made the benchmark by running custom VBA macro, (which we use in our company) that generates 284 pages long Word document full of Excel Pie charts, tables and comments. The macro is run as a single task (excluding the standard services) on a set of identically configured Windows XP 32-bit systems. I measured the time (in sec.) needed to perform the test. The computer (i.e. my notebook Asus P53E) supports both VT-d extensions and native Windows XP. It has 2-core processor, each core is hyperthreaded, so in total we have 4 mostly independent execution units. I use the latest VirtualBox 4.2 and VMWare Workstation 9.0 for Linux, installed together on the same host (running Mint 13 Maya) but never run simultaneously. The results (in column Time) are no less accurate than ± 10% Here are the results (sorry for the format, but I couldn't find out a better solution for tables in SO): +---------------+-------------+------------------------------------------------------+---------+------------+----------------+------+ | Host software | # processor | Windows kernel | IO APIC | VT-x/AMD-V | 2D Video Accel | Time | +---------------+-------------+------------------------------------------------------+---------+------------+----------------+------+ | VirtualBox | 1 | Advanced Configuration and Power Interface (ACPI) PC | 0 | 1 | 0 | 1139 | | VirtualBox | 1 | Advanced Configuration and Power Interface (ACPI) PC | 0 | 1 | 1 | 1050 | | VirtualBox | 1 | Advanced Configuration and Power Interface (ACPI) PC | 0 | 0 | 1 | 1644 | | VirtualBox | 4 | ACPI Multiprocessor PC | 1 | 1 | 1 | 6809 | | VMWare | 1 | ACPI Uniprocessor PC | | 1 | 1 | 1175 | | VMWare | 4 | ACPI Multiprocessor PC | | 1 | 1 | 3412 | | Native | 4 | ACPI Multiprocessor PC | | | | 1693 | | Native | 1 | Advanced Configuration and Power Interface (ACPI) PC | | | | 1170 | +---------------+-------------+------------------------------------------------------+---------+------------+----------------+------+ Here are the striking conclusions: Although I've read in the VirtualBox fora about abysmal performance with 32-bit guest on 64-bit host, VMWare also has problems compared to native run, still being twice faster(!) than VBox. Although VBA is inherently single-threaded, the Excel calculations, which take much more than a half of total computation time, supposedly aren't. So one would expect some speed gain when running on 2+ cores ("+" for hyperthreading). What we see is a speed loss. And quite big one too. For the VirtualBox the VT-d extension isn't a big deal. Can anyone shed some light on why the singlethreaded Windows kernel is so much faster than the SMP one?

    Read the article

  • Some questions regarding Hostname

    - by user481913
    I just bought a new VPS hosting plan and i have a few questions. Hope someone here can clear the doubts for me. 1) Is it necessary to have a real domain for a vps hostname? I suppose i can just use a non-real domain like anydomain.com and something like 'server' for the computer name. Therefore i'll end up with something like server.anydomain.com as the vps's hostname. I want to do this for the sake of putting in a hostname to configure the vps to get it going . So, since this non-real domain name does not need to be publicly accessible i don't need to register or own it and instead access the server by the ip address. Is that correct? But i suppose that this also depends upon if my web host allows that? 2)I would also like to run some real sites with real domain names on this vps, so can i just configure the zone file on the primary nameserver and make entries for these domains and point an A record at the Vps's IP to make them publicly accessible over the internet? For example for my 1st domain i could make an entry like this: $TTL 86400 mydomain1.com. IN SOA ns1.mywebhost.com. \ admin.mydomain1.com. ( 2004011522 ; Serial no., based on date 21600 ; Refresh after 6 hours 3600 ; Retry after 1 hour 604800 ; Expire after 7 days 3600 ; Minimum TTL of 1 hour ) server IN A 200._._._ ns1.mywebhost.com. IN A 216._._._ ns2.mywebhost.com. IN A 205._._._ @ IN NS ns1.mywebhost.com. @ IN NS ns2.mywebhost.com. @ IN MX 10 server www IN CNAME server server IN CNAME @ (so this particular line tells the nameserver to point the url mydomain1.com to server.anydomain.com at the particular ip addresss in the A record.... is that right?) Similarly for my 2nd domain i could have a similar entry : $TTL 86400 mydomain2.com. IN SOA ns1.mywebhost.com. \ admin.mydomain2.com. (..... ............................so on........ ......................................... ......................................... ......................................... ......................................... ......................................... Is that correct? 3) Suppose for my vps hostname, i ignorantly chose a domain that someone else alreadys owns , however i think that it won't affect the public accessibility of the real domain or website since only the real owner of the domain has the rights to provide for the nameservers addresses in the TLD registeries through his Domian Registerar? Is that correct? 4)Can i change my vps's hostname later? Would this create any complications?

    Read the article

  • Sharing folder in a Virtual Private Windows Server 2008 R2 ?

    - by Triztian
    See Edit 2: Hello all, seems my involvement with computers has grown and I've found my self in the need to access a shared folder on a server. I've read some documentation and managed to set up the folder as a share, for this I created a local group and for now just one local user that has access to the share, the folder is in the public user folder and it's permissions should be (and I believe they are) read/write. The problem is that I can't connect from a remote machine I mean I don't know how the way it should be accessed, the server has a public IP and we use it also as a host to our website I don't know if that affects it though, the folder will be used as the "keeper" for the QuickBooks company files and has the database server manager installed. I've tried setting up a VPN Connection to the but no success. The server has a domain name a "http://www.example.com" that redirects to our website, I am unsure if it could be accessed that way, also the share has a location displayed when I right-click properties Heres what I've tried Setting up a VPN Connection (Windows Vista and 7) Got to the point where I got asked for credential and entered the user I created (which is not an admin) but I got a "Connection fail error 800" I suppose this is because in the domain field I entered the servers workgroup. right-click add network connection (Windows 7) Went through the wizard until I reached the point of entering the location, tried many things, the name in the share's properties(\\SOMETHING\Share), the http://www.example.com , the IP address I'm quite unfamiliar with this, so I have my guesses: Since the group and user are local they do not have access to the folder. The firewall in the server is blocking my connection. Anyways, any help and guidence is truly appreciated. EDIT 1: As @tony roth pointed out it may be a security fail, an I commented it out to management and said that that is not an issue, so please bare with me. EDIT 2: I've found out that the real question could be streamlined to "Sharing folder in a Virtual Private Server?", as thats what we have, a virtual private windows server 2008 R2, and I would like to know how to make it show like a normal folder in the client computer. Thanks again for all of your support.

    Read the article

  • XCP Project Kronos syslog error: "irq ... : nobody cared" on Dom0 host

    - by Vlad Fedin
    One of our production clusters driven by XCP suddenly went uresponsive. After restart and some investigation we found such logs in dom0 machine syslog: Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659040] irq 339: nobody cared (try booting with the "irqpoll" option) Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659058] Pid: 0, comm: swapper/3 Tainted: G C O 3.2.0-24-generic #37-Ubuntu Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659060] Call Trace: Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659062] <IRQ> [<ffffffff810db37d>] __report_bad_irq+0x3d/0xe0 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659071] [<ffffffff810db605>] note_interrupt+0x135/0x190 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659074] [<ffffffff810d8e69>] handle_irq_event_percpu+0xa9/0x220 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659078] [<ffffffff8130ff3b>] ? radix_tree_lookup+0xb/0x10 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659081] [<ffffffff810d9031>] handle_irq_event+0x51/0x80 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659084] [<ffffffff810dc187>] handle_edge_irq+0x87/0x140 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659089] [<ffffffff813a8829>] __xen_evtchn_do_upcall+0x199/0x250 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659092] [<ffffffff813aa96f>] xen_evtchn_do_upcall+0x2f/0x50 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659096] [<ffffffff81666d3e>] xen_do_hypervisor_callback+0x1e/0x30 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659097] <EOI> [<ffffffff810013aa>] ? hypercall_page+0x3aa/0x1000 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659104] [<ffffffff810013aa>] ? hypercall_page+0x3aa/0x1000 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659107] [<ffffffff8100a1d0>] ? xen_safe_halt+0x10/0x20 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659110] [<fff IRQ 339 in cat /proc/interrupts: 339: ... xen-pirq-msi-x eth0 where eth0 is hardware NIC. While host machine seems to hang, guest machines continue to work, so our tiny internal monitoring on one of the virtual hosts logged something like that: [2012-10-26 20:31:51] [OK......] 200 OK : 113159149 ns [2012-10-26 20:32:40] [DISASTER] 500 Can't connect to [hostname]:80 (No route to host) : 47763284432 ns ... [2012-10-26 20:34:40] [DISASTER] 500 Can't connect to [hostname]:80 (No route to host) : 46894835070 ns [2012-10-26 20:34:57] [DISASTER] 500 Can't connect to [hostname]:80 (Bad hostname) : 16821741955 ns ... [2012-10-26 20:38:18] [DISASTER] 500 Can't connect to [hostname]:80 (Bad hostname) : 20103298289 ns [2012-10-26 20:38:37] [DISASTER] 500 Can't connect to [hostname]:80 (Bad hostname) : 17895754943 ns Host and guest OS: Ubuntu 12.04 LTS, 05:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection Subsystem: ASUSTeK Computer Inc. Device 8369 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at fe500000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at e000 [size=32] Region 3: Memory at fe520000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: e1000e Kernel modules: e1000e Any hints how to debug this?

    Read the article

  • How to encrypt dual boot windows 7 and xp (bitlocker, truecrypt combo?) on sdd (recommended?)

    - by therobyouknow
    I would like to setup a dual boot Windows 7 and Windows XP laptop/notebook computer where each operation system's partition is fully encrypted. I would like to do this on a SSD - a 128Gb Crucial M4. My research Dual boot of truecrypt encrypted OSs on one drive (not possible - in Truecript 7.x at time of writing) This cannot be done on a standard Truecrypt setup - it will only support encrypting one of the operating systems. I have tried this and also read about it here on superuser.com However, I did see a solution here that uses grub4dos as the initial bootloader to chain to separate truecrypt encrypted OSs, in my case Windows 7 and Windows XP: http://yyzyyz.blogspot.co.uk/2010/06/truecrypt-how-to-encrypt-multiple.html I am not going to consider this solution as it relies upon some custom code for use in the bootloader that is provided by the author. I would prefer a solution that can be fully understood so that I can be sure that there is nothing undesirable occuring (i.e. malware or just simply bugs in the code). I would like to believe such a solution doesn't have those risks but I can't be sure. BitLocker and Truecrypt combination - possible solution? So I am now considering a combination of encryption programs: I now aim to encrypt Windows XP with Truecrypt and Windows 7 with BitLocker. Assuming Truecrypt bootloader can boot into non-Truecrypt OSs (e.g. via hitting Escape to go to another menu), then this solution may be viable. SSDs and Encryption (use fastest possible spinning hard disk instead (?)) I read on various superuser.com posts and elsewhere that current SSDs are not suited to whole drive encryption for various reasons: impact of performance algorithms that give SSDs advantage over spinning harddisks. Algorithms used in compression of data for example. Wear on the SSD, shortening its life Security issues whereby data is repeated, as indicated in some Truecrypt documentation So I am now considering not using SSD. But with the aim to have the fastest drive possible, I am considering using the Western Digital Scorpion black 2.5" 7200rpm harddisk as this appears to be top rated among spinning platter-based harddrives (don't work for Western Digital). Summary So to achieve whole drive encrypted dual boot Windows 7 and Windows XP with minimal performance impact I intend to use a combination of Truecrypt and Bitlocker on a top-rated conventional spinning platter-based harddisk. Questions Will my summary: achieve whole disk encryption of the dual-boot Windows XP, Windows 7? OR an you suggest a simpler solution, including one that only requires only Truecrypt (BitLocker not available on XP). Or another encryption tool, including paid-for? provide the highest performance. Am I correct to avoid using SDD with encryption for the reasons I discovered? Are the concerns about SSDs and encryption still very real (some articles I read go back to 2010) Thanks for your input!

    Read the article

  • Real-time offline folder-to-folder backup application needed (Windows)

    - by niktech
    I recently started using Intel Matrix Storage RAID solution that allowed me to use my 5 1TB drives for two RAID volumes. First one a 1TB RAID 0 striped across all 5 drives and second one a RAID 5 across the rest of the free space on all drives (around 2.85TB usable space). The RAID 0 I use for OS, applications and games while the RAID 5 I use as a more-permanent type storage (photos, etc). Now I do realize that running the OS and applications on RAID 0 across 5 drives is very dangerous, which is what brings up the following question. Is there a reliable freeware realtime backup application that can backup a set of folders from one drive to another drive (no online backups needed)? I've already tried a few (Mozy, Yadis, Comodo Backup, GFI Backup, Idoo, Crash Plan) but none meet my requirements: Low CPU and RAM usage. Realtime Backups - as soon as a file is modified in the source folder, it is added to the backup queue which will be processed with the lowest priority when the CPU is idle. This backup queue should persist in cases of computer restarts (ie: the source and destination folders should always have the same set of files, except for the ones waiting in the backup queue). Incremental Backups - if only 10 bytes changed in a 1GB file, the app should only copy those 10 new bytes. Ability to back up locked and opened files (some apps, like Yadis, can't back up critical files like browser favorites). Ability to run as a service (no need for any user to log-in to have the app started). Optional requirements: Compression of the destination into a well-known format (RAR, Zip) that can be directly read without the use of the application. Preset source folders (such as Browser Favorites, Game Saves, Application Settings, etc). The idea is to use RAID 0 array as "semi-persistent RAM-like" storage which in case of a failure can be quickly rebuilt by reinstalling the OS, apps and games and copying over the settings, saves, favorites from the RAID 5. I'm also thinking of taking this RAID 0 as RAM idea to the extreme with SSDs (as soon as we get some nice 6Gb/s SATA III SSDs out there), where a couple of SSDs chained in RAID 0 will work as yet another semi-persistent cache layer sitting between the RAM and the HD. I'm just hoping there already exists an application that satisfies these requirements... otherwise I'll have to write one myself, which I would prefer not to do.

    Read the article

  • What part of SMF is likely broken by a hard power down?

    - by David Mackintosh
    At one of my customer sites, the local guy shut down their local Solaris 10 x86 server, pulled the power inputs, moved it, and now it won’t start properly. It boots and then presents a prompt which lets you log in. This appears to be single user milestone (or equivalent). Digging into it, I think that SMF isn’t permitting the system to go multi-user. SMF was generating a ton of errors on autofs, after some fooling with it I got it to generate errors on inetd and nfs/client instead. This all tells me that the problem is in some SMF state file or database that needs to be fixed/deleted/recreated or something, but I don’t know what the actual issue is. By “generate errors”, I mean that every second I get a message on the console saying “Method or service exit timed out. Killing contract <#.” This makes interacting with the computer difficult. Running svcs –xv shows the service as “enabled”, in state “disabled”, reason “Start method is running”. Fooling with svcadm on the service does nothing, except confirm that the service is not in a Maintenance state. Logs in /lib/svc/log/$SERVICE just tell you that this loop has been happening once per second. Logs in /etc/svc/volatile/$SERVICE confirm that at boot the service is attempted to start, and immediately stopped, no further entries. Note that system-log isn’t starting because system-log depends on autofs so I have no syslog or dmesg. Googling all these terms ends up telling me how to debug/fix either autofs or nfs/client or inetd or rpc/gss (which was the dependency that SMF was using as an excuse to prevent nfs/client from “starting”, it was claiming that rpc/gss was “undefined” which is incorrect since this all used to work. I re-enabled it with inetadm, but inetd still won’t start properly). But I think that the problem is SMF in general, not the individual services. Doing a restore_repository to the “manifest_import” does nothing to improve, or even detectibly change, the situation. I didn’t use a boot backup because the last boot(s) were not useful. I have told the customer that since the valuable data directories are on a separate file system (which fsck’s as clean so it is intact) we could just re-install solaris 10 on the / partition. But that seems like an awfully windows-like solution to inflict on this problem. So. Any ideas what piece is broken and how I might fix it?

    Read the article

  • Add user in CentOS 5

    - by Ron
    I created a new user in my CentOS web server with useradd. Added a password with passwd. But I can't log in with the user via SSH. I keep getting 'access denied'. I checked to make sure that the password was assigned and that the account is active. /var/log/secure shows the following error: Aug 13 03:41:40 server1 su: pam_unix(su:auth): authentication failure; logname= uid=500 euid=0 tty=pts/0 ruser=rwade rhost= user=root Please help, Thanks Thanks for the responses so far: I should add that it is a VPS on a remote computer, fresh out of the box. I can log in as the root user quite fine. I can also su to the new user, but I cannot log in as the new user. Here is my sshd_config file: # $OpenBSD: sshd_config,v 1.73 2005/12/06 22:38:28 reyk Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/usr/local/bin:/bin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. #Port 22 #Protocol 2,1 Protocol 2 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh/ssh_host_rsa_key #HostKey /etc/ssh/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 768 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH SyslogFacility AUTHPRIV #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes #StrictModes yes #MaxAuthTries 6 #RSAAuthentication yes #PubkeyAuthentication yes #AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no PasswordAuthentication yes # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes ChallengeResponseAuthentication no # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no GSSAPIAuthentication yes #GSSAPICleanupCredentials yes GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication mechanism. # Depending on your PAM configuration, this may bypass the setting of # PasswordAuthentication, PermitEmptyPasswords, and # "PermitRootLogin without-password". If you just want the PAM account and # session checks to run without PAM authentication, then enable this but set # ChallengeResponseAuthentication=no #UsePAM no UsePAM yes # Accept locale-related environment variables AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL #AllowTcpForwarding yes #GatewayPorts no #X11Forwarding no X11Forwarding yes #X11DisplayOffset 10 #X11UseLocalhost yes #PrintMotd yes #PrintLastLog yes #TCPKeepAlive yes #UseLogin no #UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #ShowPatchLevel no #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner /some/path # override default of no subsystems Subsystem sftp /usr/libexec/openssh/sftp-server

    Read the article

  • Loss of wireless network connectivity when playing video via HDMI cable

    - by Jeff Fohl
    Hi Folks - New to Super User, so I hope this question fits in with the guidelines. Very strange problem I am having, and I am at a loss as to how to continue troubleshooting this one. The basic problem is that when I attempt to watch streamed video on a particular display device (an Optoma HD180 projector), my network connectivity drops like a stone to barely measurable levels. This is my setup: I have a Dell H2C 730x running Windows 7 64bit. This particular computer has two ATI Radeon HD 4800 video cards. I have two Samsung 22" monitors connected to one card, and an Optoma HD180 digital projector connected to the other card via an HDMI cable. My internet connection is normally a reliable 6Mbps. The problem I am having occurs when I stream video (or even just browse the web) on the Optoma Projector. When I do this, my internet connection drops to practically zero (just a few kilobits per second). When I move the browser away from the projector, and over to one of my Samsung monitors, the internet connection comes right back. Note that the Optoma projector is on and enabled as a third monitor all this time. I can move the mouse around on the projector without triggering the problem. I tried pinging my router when I was playing a movie on one of the monitors, and I get a 1 millisecond response. However, when I have the movie playing on the Optoma projecter, pinging the router gives me response times in the hundreds of milliseconds, or times out completely. So, it clearly is something local to my machine - and not some sort of throttling occurring down the line. I would think that it is possibly something to do with the HDMI driver conflicting somehow with my network driver (which is a USB-based wireless connection). This one has me really stumped. Anyone have any ideas? EDIT: I am now leaning towards the possibility that the HDMI cable is somehow interfering with the wireless network, when large amounts of data are being pushed through the cable. Is this possible?

    Read the article

  • 40k Event Log Errors an hour Unknown Username or bad password

    - by ErocM
    I am getting about 200k of these an hour: An account failed to log on. Subject: Security ID: SYSTEM Account Name: TGSERVER$ Account Domain: WORKGROUP Logon ID: 0x3e7 Logon Type: 4 Account For Which Logon Failed: Security ID: NULL SID Account Name: administrator Account Domain: TGSERVER Failure Information: Failure Reason: Unknown user name or bad password. Status: 0xc000006d Sub Status: 0xc0000064 Process Information: Caller Process ID: 0x334 Caller Process Name: C:\Windows\System32\svchost.exe Network Information: Workstation Name: TGSERVER Source Network Address: - Source Port: - Detailed Authentication Information: Logon Process: Advapi Authentication Package: Negotiate Transited Services: - Package Name (NTLM only): - Key Length: 0 This event is generated when a logon request fails. It is generated on the computer where access was attempted. The Subject fields indicate the account on the local system which requested the logon. This is most commonly a service such as the Server service, or a local process such as Winlogon.exe or Services.exe. The Logon Type field indicates the kind of logon that was requested. The most common types are 2 (interactive) and 3 (network). The Process Information fields indicate which account and process on the system requested the logon. The Network Information fields indicate where a remote logon request originated. Workstation name is not always available and may be left blank in some cases. The authentication information fields provide detailed information about this specific logon request. - Transited services indicate which intermediate services have participated in this logon request. - Package name indicates which sub-protocol was used among the NTLM protocols. - Key length indicates the length of the generated session key. This will be 0 if no session key was requested. On my server... I changed my adminstrative username to something else and since then I've been inidated with these messages. I found on http://technet.microsoft.com/en-us/library/cc787567(v=WS.10).aspx that the 4 means "Batch logon type is used by batch servers, where processes may be executing on behalf of a user without their direct intervention." which really doesn't shed any light on it for me. I checked the services and they are all logging in as local system or network service. Nothing for administrator. Anyone have any idea how I tell where these are coming from? I would assume this is a program that is crapping out... Thanks in advance!

    Read the article

  • Windows 2003 Storage Server Hanging on Large File Transfers

    - by user25272
    In one of our offices we have a Dell PowerVault 745N NAS device which acts as the main file server. Its running 32bit Windows 2003 Storage Server SP2 with 3GB RAM. The server holds around 60 users HOME folders, which are mapped via AD. The office clients are a mix of XP SP3, Vista and Windows 7. Occasionally the server will completely hang when transferring large files. When the hang happens the console becomes unresponsive with only the mouse active and blank wallpaper. Sometimes stopping the copy frees the server, sometimes not. The hanging can last around 20 minutes. During this time other servers also become unresponsive with blank wallpaper at the console. If you do manage to get onto another server the taskbar and run commands are unresponsive. This also transcends to the client computers sometimes with explorer crashing. I'm guessing this is due to the HOME folder mapping. Eventually the NAS server with free up and everything will be back to normal. The server is configured as follows: PERC 4/DC DATA 2 - 12 SCSI HDD - RAID5 SHADOWCOPY 2 SCSI HDD - RAID1 CERC SATA DATA 11 4 SATA HDD - RAID5 OS 4 SATA HDD - RAID5 All the drivers and firmware is up to date. I've been through all the diagnostics with Dell and the hardware has come up clean including full HDD tests on the arrays. The server has NOD32 installed as the AV, but the hanging happens when it is uninstalled. There are no errors in the event log when this happens and we don't have any errors logged on any of our ProCurve switches. DNS is fine on the domain and AD from what I can tell is running happily. There are no DFS or NFS shares setup either. All the shares are standard Windows. I've unchecked the allow the computer to turn off this device to save power box under Power Management on the NIC. "Set Link Speed and Duplex to Auto-negotiate 1000 " Increased Receive Descriptors buffer from 256 to 352 (reserves more CPU resource for handling data) I've run network traces using network monitor and have found the following: 417 8.078125 {SMB:192, NbtSS:25, TCP:24, IPv4:23} 192.168.2.244 192.168.5.35 SMB SMB:R; Nt Create Andx - NT Status: System - Error, Code = (52) STATUS_OBJECT_NAME_NOT_FOUND I've tried different cabling; NICs and switch ports all with the same result. Transferring files from other servers on the domain is fine. All I haven't done is run CHKDSK on the drives to look for any file system errors. On the Vista clients I have also run netsh interface tcp set global autotuning=disabled with no result. Could it be that the server has a faulty drive or that the I/O is too much for it to handle? Any ideas why would the hang cause issues with the other servers on the LAN? Many Thanks.

    Read the article

< Previous Page | 722 723 724 725 726 727 728 729 730 731 732 733  | Next Page >