Search Results

Search found 18907 results on 757 pages for 'computer history'.

Page 728/757 | < Previous Page | 724 725 726 727 728 729 730 731 732 733 734 735  | Next Page >

• USB hard drive not recognized

  - by user318772

  Until recently I was using the portable USB hard drive in my win 7 laptop and ubuntu laptop. Suddenly now none of the laptops recognize it. This is the message i get by doing lsusb... Bus 001 Device 004: ID 1058:1010 Western Digital Technologies, Inc. Elements External HDD Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 003: ID 0b97:7762 O2 Micro, Inc. Oz776 SmartCard Reader Bus 003 Device 002: ID 0b97:7761 O2 Micro, Inc. Oz776 1.1 Hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 413c:a005 Dell Computer Corp. Internal 2.0 Hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub fdisk doesn't show the external hard drive Disk /dev/sda: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders, total 156301488 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0004a743 Device Boot Start End Blocks Id System /dev/sda1 * 2048 152111103 76054528 83 Linux /dev/sda2 152113150 156301311 2094081 5 Extended /dev/sda5 152113152 156301311 2094080 82 Linux swap / Solaris when i do testdisk TestDisk 6.14, Data Recovery Utility, July 2013 Christophe GRENIER <[email protected]> http://www.cgsecurity.org TestDisk is free software, and comes with ABSOLUTELY NO WARRANTY. Select a media (use Arrow keys, then press Enter): >Disk /dev/sda - 80 GB / 74 GiB - ST980825AS Disk /dev/sdb - 2199 GB / 2048 GiB testdisk-> Intel->analyse I get partition error Disk /dev/sdb - 2199 GB / 2048 GiB - CHS 2097152 64 32 Current partition structure: Partition Start End Size in sectors Partition: Read error Here is the output of dmesg [11948.549171] Add. Sense: Invalid command operation code [11948.549177] sd 2:0:0:0: [sdb] CDB: [11948.549181] Read(16): 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 [11948.550489] sd 2:0:0:0: [sdb] Invalid command failure [11948.550495] sd 2:0:0:0: [sdb] [11948.550499] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [11948.550505] sd 2:0:0:0: [sdb] [11948.550508] Sense Key : Illegal Request [current] [11948.550514] Info fld=0x0 [11948.550519] sd 2:0:0:0: [sdb] [11948.550525] Add. Sense: Invalid command operation code [11948.550531] sd 2:0:0:0: [sdb] CDB: [11948.550534] Read(16): 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 [11948.551870] sd 2:0:0:0: [sdb] Invalid command failure [11948.551876] sd 2:0:0:0: [sdb] [11948.551880] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [11948.551885] sd 2:0:0:0: [sdb] [11948.551888] Sense Key : Illegal Request [current] [11948.551895] Info fld=0x0 [11948.551900] sd 2:0:0:0: [sdb] [11948.551905] Add. Sense: Invalid command operation code [11948.551911] sd 2:0:0:0: [sdb] CDB: [11948.551914] Read(16): 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 If possible i want to retrive at least some data from this hard drive. If thats not possible I would like to format it and use it. Any help will be greatly appreciated Thanks

  Read the article

• Why does Excel now give me already existing name range error on Copy Sheet?

  - by WilliamKF

  I've been working on a Microsoft Excel 2007 spreadsheet for several days. I'm working from a master template like sheet and copying it to a new sheet repeatedly. Up until today, this was happening with no issues. However, in the middle of today this suddenly changed and I do not know why. Now, whenever I try to copy a worksheet I get about ten dialogs, each one with a different name range object (shown below as 'XXXX') and I click yes for each one: A formula or sheet you want to move or copy contains the name 'XXXX', which already exists on the destination worksheet. Do you want to use this version of the name? To use the name as defined in destination sheet, click Yes. To rename the range referred to in the formula or worksheet, click No, and enter a new name in the Name Conflict dialog box. The name range objects refer to cells in the sheet. For example, E6 is called name range PRE on multiple sheets (and has been all along) and some of the formulas refer to PRE instead of $E$6. One of the 'XXXX' above is this PRE. These name ranges should only be resolved within the sheet within which they appear. This was not an issue before despite the same name range existing on multiple sheets before. I want to keep my name ranges. What could have changed in my spreadsheet to cause this change in behavior? I've gone back to prior sheets created this way and now they give the message too when copied. I tried a different computer and a different user and the same behavior is seen everywhere. I can only conclude something in the spreadsheet has changed. What could this be and how can I get back the old behavior whereby I can copy sheets with name ranges and not get any errors? Looking in the Name Manager I see that the name ranges being complained about show twice, once as scope Template and again as scope Workbook. If I delete the scope Template ones the error goes away on copy however, I get a bunch of #REF errors. If I delete the scope Workbook ones, all seems okay and the errors on copy go away too, so perhaps this is the answer, but I'm nervous about what effect this deletion will have and wonder how the Workbook ones came into existence in the first place. Will it be safe to just delete the Workbook name manager scoped entries and how might these have come into existence without my knowing it to begin with?

  Read the article

• How to flip video feed that's presented upside down?

  - by Zuul

  Skype an other applications running under windows 7 Ultimate are presenting the video captured from the laptop built-in webcam upside down. I've tried many solution that I was able to find regarding issues like this, but to no avail. Some of the most relevant are discussed here: From Skype Support Network, the thread why is my video image of myself upside-down??? From ASUSTek Forums, the thread Built-in camera upside down Both present several potential solutions to this issue, but I've been unable to fix it for the laptop ASUS U6S. What I've already tried: Changing Drivers The driver that works must be the one from Windows, all others available from ASUS drivers either don't install or install but the webcam doesn't provide any video feed. This disallows all options that concern using an older driver or editing the .inf file as to manually adjust the settings. ASUS does not provide drivers for Windows 7, so I've used drivers from Windows Vista 32 Bit. Using the application manycam This application actually solves the issue (temporarily), but creates new ones: If I use the application to flip the video feed, Skype video call cease to work. This application doesn't save the settings, at least I wasn't able to find any way to save the settings I've used to flip the video feed. A computer restart brings all back to how it was, video feed upside down and if the application is still installed, Skype continues to fail on video calls. Regedit I've searched thru Windows Registry Editor as to find any reference to the webcam settings, hopping to find a key with the Flip parameter, since it's up to the driver to flip the image (by what I could ascertain from this problem). Couldn't find any reference to such settings, either they actually don't exist within the Windows Registry or they use some weird name that I could think off. System Configuration I was able to access the webcam system settings from the Windows Device Manager, but the tab that actually has the Image Rotation setting is always disabled. The same goes for the settings available from the Skype webcam options (that essentially is presenting the same settings as Windows Device Manager, just within a custom Skype pop-up). Question: How can I flip the video feed from the laptop's built-in webcam, as to properly see and broadcast the video?

  Read the article

• iTunes and Hulu Playback Choppy and Slow?

  - by Bart Silverstrim

  Specs: Windows XP, latest updates 1.7 ghz Pentium 4 1 gig ram DirectX 9.0c NVIDIA GeForce FX 5200 with 256 meg RAM OpenGL 2.1 The story: Okay, I had an older system laying around that I figured I would try turning into a mini-media system to connect to our TV. I put together a lot of older parts, got it into working order, etc. and hooked it up and voila'...slower, but usable system that displayed to the TV. It could run some things decently. I put in iTunes, it played video okay. Not great, but okay. Played Hulu and since we have a 1Mb download rate, the minimum for their site, there were some choppy moments when watching their shows, but I found that (sadly) changing resolution to 800x600 seemed to help with the issue when running full screen. I downloaded the application called Boxee and installed it. It wouldn't run; apparently the video card in the system supported OpenGL 1.2, and needed at least 1.4. I bought a cheap card, the 5200, with four times the memory in it and support for OpenGL 2.1. Installed, everything seemed fine. iTunes seemed to run fine, the video driver (PNY video card) came with OpenGL 2.1, and Boxee finally ran. I then upgraded to the latest drivers for the video card and ran the DirectX updater from MS. After that, the OpenGL Extension Viewer wouldn't run. It just stayed as an icon in the task bar. Also, any and all videos in iTunes stuttered and went out of sync horribly. Unwatchable. I tried watching Hulu video in Boxee, and it displayed video like it was a series of stills in a very bad powerpoint. Playing straightforward audio-only came through fine, no stutters no hiccups. I tried system restore to roll back updates to pre-directX updates (I thought that seemed to be the time that triggered the weird behavior), no joy. I tried uninstalling and reinstalling the video drivers. I installed updated audio drivers (ensoniq audiopci), nothing helped. I finally wiped the drive last night and tried reinstalling everything and restoring my iTunes content via an import from a backup. Fresh install, no updater on the video card or directx. the problem was still there although I haven't tested Hulu, the iTunes player is still stuttering like crazy if I play video, fine if I play audio. I know the processor isn't high in heft, but with one gig of RAM and the fact that it seemed to do okay before I thought that the problem must be software related. Has anyone else run into this sort of issue and have a solution other than "buy a new computer"? What specs seem to work with video at the low end for you? Right now the system is of little use other than keeping my music library and iTunes apps synced with my iPod.

  Read the article

• I can't delete a directory inside a junctioned directory

  - by Fredy Muñoz

  So this is the deal. A couple of days ago I moved my profile folder C:\Documents and Settings\fmunoz to a different drive D:\fmunoz. Today, I created a directory in my desktop using the point-and-click method: Right-click on an empty space in the desktop Select New Select Folder Leave the default name New Folder and press Enter I tried to delete the folder using the point-and-click method: Right-click the New Folder directory Select Delete After five seconds, I got the following message: --------------------------- Error Deleting File or Folder --------------------------- Cannot delete New Folder: Access is denied. Make sure the disk is not full or write-protected and that the file is not currently in use. --------------------------- Initially I thought that there must be some sort of indexing services locking the directory so I got a list of open files using the TuneUp Process Manager tool but the New Folder directory wasn't there. I double-clicked My Computer, navigated to the desktop directory C:\Documents and Settings\fmunoz\Destkop, tried to delete the New Folder directory using the same point-and-click method described above and got exactly the same message at the same amount of time. In the same window, I navigated to the actual location of the desktop directory D:\fmunoz\Desktop, tried to delete the New Folder directory and this time it worked. I thought that this behavior was due to some special treatment that Windows gives to the desktop or the profile directories so I tried doing the same thing with a different set of directories: Created a folder D:\dummy Created a junction C:\dummy pointing to D:\dummy Created a New Folder directory in C:\dummy Tried to delete New Folder from C:\dummy. Didn't work. Tried to delete New Folder from D:\dummy. It worked. I tried creating the folder in the actual directory rather than the junction directory: Created a New Folder directory in D:\dummy Tried to delete New Folder from C:\dummy. Didn't work. Tried to delete New Folder from D:\dummy. It worked. I also tried using the Delete button instead of using the Delete option of the context menu but it didn't work. When using the Shift+Delete sequence, it works. It also works by using the rd command in the console, but in both cases the deleted directory doesn't goes to the Recycle Bin, which is my intention when using the Delete context menu option or the Delete button.

  Read the article

• QNAP (469L) with Debian: can't connect to router

  - by agtoever

  I've been running my QNAP 469L with Debian (Wheezy deb7u3) for a few months. Yesterday I upgraded the memory to 4 GB. The system boots fine, but since the upgrade, I'm not able to connect the server to my router (a TP-Link WR941ND). My configuration: The router runs a DHCP server (192.168.67.100 and up), with a preconfigured ip address for the QNAP (192.168.67.10). The router is on 192.168.67.1. As said, Debian is installed on the QNAP (which can be regarded as a normal computer). Networking hardware on the QNAP: Intel PRO/1000 Network Connection using the e1000e kernel module. This is what I have tried so far: Replace the network cable (tried 3 different cables on different router ports). Check for messages from the kernel: dmesg | grep eth. Besides the normal hardware messages I get a ADDRCONF(NETDEV_UP): eth0: link is not ready for each call to ifup. Manually restart the network sudo server networking restart Check sudo ifconfig (eth0 is up, but no ip addresses). Check the /etc/network/interfaces which has (besides the loopback device) an allow-hotplug eth0 and iface eth0 inet dhcp, which is afaik the default Debian configuration. Since the server has two ethernet ports, I checked if I'm using the right port (checked the hardware address that ifconfig reports for eth0 is the same as the hardware address that is in the preconfigured ip address for the server in the router. Do a manual sudo ifdown eth0 && sudo ifup eth0 with no results (but an extra ADDRCONF(NETDEV_UP): eth0: link is not ready in the kernel log) Do a dhcp request dhclient -v eth0: for about a minute requests are send (according to the terminal) and at the end I get a No DHCPOFFERS received. No working leases in persistent database - sleeping.. Check the router system log if DHCP requests are received. I see them for some devices (my Mac, my iPhone) but not from the QNAP. The log entry looks like: DHCPS:Recv REQUEST from 84:85:06:07:75:6A and then a DHCPS:Send ACK to 192.168.67.101. There are no records from the QNAP's hardware address. So the two error messages that I do get are: ADDRCONF(NETDEV_UP): eth0: link is not ready for every ifup and No DHCPOFFERS received. No working leases in persistent database - sleeping. for every DHCP call.

  Read the article

• Educate me - should I buy these prebuilt NAS (which is better) or make my own?

  - by user29336

  I'm trying to learn as much as possible, and I think I've learned quite a bit so bear with me here under my confusion. I found a coupe NAS setups. I'm not sure if one is better than the other, other than the price being higher on some, and some coming with drives VS not. Let me list my setup so you can get an idea of what I want to provide: Macbook Pro Macbook Mini for Media streaming (so far) Windows 7 Gaming Computer Xbox 360 I'd like to provide a storage system for all these devices so they can access files very easily, I'd also like any of these devices to be able to stream media from this storage system. I'd like this storage system to be hassle free in terms of my confidence in the data integrity. If a drive fails, I want to know that I can replace the drive and all my files will still exist. I'd like to access this storage system OUTSIDE of my LAN. If I'm out on a job for work I'd like to go in, or be able to have people DL some files. This brings me to a question, is this what iSCSI is? I'd like this data system to be able to download torrents. I want to mount any drive on this storage system onto my OSX laptop as if it were a local drive attached. (Is this with iSCSI is?) I'd like this system to have a GOOD web based GUI. I don't want to install software to use it. I believe those are the most of my requirements. If I'm missing something that I have no knowledge about, can someone educate me? Here are the systems I found: $729ish on Newegg Lacie 5Big Network 2 (comes with 5TB of space. iSCSI / mac compatible, torrents, nice ui, + others?) Is this overpriced for what it provides? It almost seems like a great deal to me because of the 5TB of space it comes with vs the other NAS systems that don't come with storage but cost $600-700. Should I get a different NAS system? Netgear? Others? Do they have same features? Better? Is it better to buy your own disks? What about making my own? I'm tech savy all around. It seems cheaper to buy a premade one especially with the support/warranty it provides...

  Read the article

• Recovering from backup without original install media

  - by KGendron

  A machine from my old job had a complete hard drive failure. I have backups but I'm running into severe problems restoring from them. The only install media was a secondary restore partition on the system's hard drive. I hate whoever came up with that idea more than i can possibly express with words. I spent several days trying to recover the disk - it is pretty well shot and none of my best tricks could even get it to show up in the bios/ The machine that broke is an hp with xp media center edition on it (I don't know why either). The backups were created using the default windows backup tool - I have .bfk file on an external hardrive that i am trying to restore from. I've replaced the hard drive. My home machine is running windows 7 64bit and i'm trying to use it as a platform to restore to the other disk. I downloaded the window 7 nt-restore utility, however no matter what i do it restores to my C drive rather than the specified drive. Fortunately win7 security settings prevented it from being a complete disaster - but still not a happy thing. I tried firing up the xp virtual machine. I can browse to the backups but it says they are invalid and refuse to let me view/ continue with the restore. I tried installing XP to an extra harddrive on my machine - however it bluescreens on me during the install process and I cry. I tried installing xp pro to the new drive and attempted to restore over it, it of course blackscreened on me as that was a stupid idea. I made two partitions on the new hard drive (Apparently the bios on this accursed piece of junk doesn't allow hd partitions larger than 200G anyways and thus fails 40 minutes into the install with an ever-descriptive "Disk Read Error". Guess how i spent last weekend? My last idea was to install xp pro to the second partition and then use it to restore from backup to the first. After the first restart it gives me the error "Windows could not start because of a computer disk hardware configuration problem. Could not read from the selected boot disk. Check boot path and disk hardware". My brain made one of those bad hard drive clicky noises. I've tried several boot disks but they don't seem to work. If anyone has a link to a good one it would be greatly appreciated. Anyone have any more ideas? - I really hate asking on what seems like such a simple issue but i am quite literally at my wit's end. Thanks - and sorry for the really long post.

  Read the article

• Wireless Network suddenly cant connect after Windows update

  - by vinir

  UPDATE: As my patience started to end, the laptop started to display symptoms of other malfunctions, so I ended up returning it to Asus and actually had the price of the laptop back in store credit. I did not solve the problem per se, but as I don't have the notebook and the screen, the keyboard, the touchpad and other parts were malfunctioning, I can safely assume that it was put to rest. I don't know how to behave when my question isn't actually answered, but was "solved", so I placed this over here. Anyone that knows how to end this topic, I would appreciate the heads up. Thanks for everything, everyone, it's nice to see that this topic in the community was active even when all this time had passed. vinir So I bought an ASUS K43E notebook earlier this year and built a wireless conection to link it to. It worked great for the first weeks, but then I updated my Windows 7 Home Basic with the daily updates; After that my home network couldn't be reached no matter what I did. I have linux on dual boot on the same notebook and it can connect to my home wireless network flawlessly. I have a hunch that it's somehow related to the Network Profile settings. I have noticed my network was set as "Home network", but after the system updates I got changed to "Public". Now I can't connect to it to change the profile settings. My Atheros Network adapter is updated to the latest driver (march 2012), and I still can't connect. The funny thing is that the same thing happened to my mother's notebook, as it has the same Network Adapter, Atheros AR9285, as I recall it. I managed to fix it on my mother's computer by using an specific network LSP and profiling reset that was available through her notebook's antivirus program, avast! Internet Security. I can't get that to work on my notebook, but I suspect that some related tool might just make it work too. So the question is: how to modify a network's profile and settings that were stored in my notebook? I can't connect to the specific network on Windows, as stated before.

  Read the article

• Need help troubleshooting highly variable ping times

  - by Elliot.Bradshaw

  I'm at work using Citrix (think Remote Desktop) to connect to client sites. With my job I have to write a fair bit of code while I'm connected remotely via Citrix, so the latency of my internet connection is important. If I'm getting ping times above 250ms, then it becomes almost impossible to scroll, click or type with accuracy. Recently my Comcast business internet has been exhibiting highly variable ping times. If I ping google.com, I'll get pings that range from 9ms all the way up to 1300ms. The problem seems to be at its worst during the hours of 1PM to 4:30PM. Outside of those hours and the variance in pings settles down, mostly between 9ms and 50ms. The signal to noise ratio and upstream power are both fine on my modem--the values are here: http://pastebin.com/D4hWGPXf I ran a trace route from my computer to google.com (the results of which are here: http://pastebin.com/GcdjYvMh) and did another test ping to the IP of the first hop outside of our local network (73.98.44.1)--the variance in ping times existed in exactly the same manner as if I were pinging Google. Connecting directly to the cable modem by CAT5 makes no difference. Here is a screenshot demonstrating the variance of the ping times: http://postimage.org/image/haocdeauv/full/ -- as you can see it can get pretty bad. Three Comcast techs have been out (two of them were here when the problem wasn't happening) and they as well as the regional tier 2 Comcast support were unable to diagnose the problem. I now have a ticket open with tier 3 support, but have yet to hear back from them. Does anyone know what could cause these sorts of problems or have any idea from the traceroute above where it could be originating? The regional tier 2 guy tried to tell me that what I'm seeing is normal--are highly variable ping times like that ever acceptable? Anything I should ask Comcast to do or look at to get this problem fixed? Any tips/advice much appreciated! Edit: This is Comcast cable internet at a small start-up, we've ruled out congestion in our private LAN as a cause (i.e., no one's watching YouTube when the pings become variable). Update: Tier 3 Comcast support advised swapping out the modem, a tech came here today and did that--same problem persists.

  Read the article

• What is the difference between running a Windows service vs. running through shell?

  - by Zack

  I am trying to troubleshoot an issue on a Windows 2008 server where running attempting to connect to a "Timberline Data Source" ODBC driver crashes if the call is in a "service" context, but succeeds if the call is initiated manually in a Remote Desktop session. I have set the service to run as my user. I'm wondering if, all else being equal (user, machine, etc), are there any fundamental security/environment differences between running a process as a service vs manually? --- Implementation Details --- In case it is helpful for anyone, I had a system that started as an attempt to connect to a Timberline Database using ODBC and a Python CGI script called via IIS 7. The script itself works fine, however, as soon as I attempt to perform the ODBC connect function, the script crashes without throwing an exception. The script was able to connect fine when executed via command line. The same thing happened when using a C#/.net service, attempting to run via Apache, Windows Scheduler or even a 3rd party scheduling tool. With the last option (the 3rd party scheduling tool, pycron) I set the service up log in as my user and had the same issue (I confirmed via Task Manager that the process running user was, in fact, me). It just doesn't make sense to me why a service, which should be running as my user, appears to still be operating in a different security context or environment. Also, if it's important, the Timberline database is referenced by computer name on the network ("\\timberline-server\Timberline Office\Accounts\AT" or something to that effect) I also realized that, as Joel pointed out, the server DOES have a mapped drive ("Y:" which is mapped to "\\timberline-server\Timberline Office") The DSN is set up at the "System DSN" level which, according to the ODBC Administration Tool, means that the DSN is available to users and services Since I'm not allowed to answer this question yet, I'll post the solution that I arrived on: As Joel Coel mentioned, there actually was a mapped drive scenario. I didn't realize this because the DSN specified a path using UNC. However, it seems as though the actual Timberline Driver referred to a mapped drive. Since services don't start with the mapped drive, I was forced to add the drive mapping code into my service. Since it was written in python, I used code from a Stackoverflow answer that was able to map the drive on the fly.

  Read the article

• How to install RAID drivers on already installed Windows 7?

  - by happysencha

  64-bit Windows 7 Ultimate 6GB RAM Intel i7 920 Intel X25-M SSD 80GB 2,5" Club 3D Radeon HD5750 GA-EX58-UD4P Motherboard I've been running fine with Windows 7 installed on the SSD. I wanted to create an mirrored Raid-1 setup for backups using two hard disks, so I ordered two Samsung HD203WI. This motherboard supports two different RAID controllers, the Intel's ICH10R and Gigabyte's SATA2 SATA controller. There are 6 SATA ports behind the ICH10R and 2 SATA ports for the Gigabyte controller. I googled around and seemed that the ICH10R is a better choice and since then I've been trying to make it work. When I activate the [RAID] mode from BIOS, the Windows 7 gives BSOD exactly as described by this guy: "Windows 7 will start to boot, it gets to the screen where there are 4 colors coming together and it blue screens and restarts no matter what I do." First thing I did: turned off the RAID and booted to Windows and tried to install the SATA RAID drivers from Gigabyte. I launch the driver installation program and it gives "This computer does not meet the minimum requirements for installing the software" error. I then tried Intel's Rapid Storage Technology drivers (which apparently is the same as the one offered at Gigabyte's site), but it resulted in exactly the same error. I then detached the new Samsung hard disks from the SATA ports, but left the [RAID] enabled in BIOS. To my surprise, it still BSOD'd, so at this point I knew it is an OS/driver issue. Also, I tried with the Gigabyte's RAID enabled (while the ICH10R RAID disabled) and it booted just fine. So then I thought, that maybe I can't install the RAID drivers from within the OS. So I caused the BSOD on purpose once again, and then with ICH10R RAID activated and Samsung hard disks attached, I choose the Windows 7 Recovery mode in the boot menu. It sees some problem(s), tries to repair, does not succeed and does not ask for drivers (which I put on a USB stick) to install. I also tried to use the command-line in the recovery: "rundll32 syssetup, SetupInfObjectInstallAction DefaultInstall 128 iaStor.inf" but it gave "Installation failed." So I'm clueless how should I proceed. Do I really need to re-install Windows 7 and load RAID drivers in the Win7 setup? I don't want to install any OS on the RAID, the Windows 7 is and will be on the SSD. I just want to have a RAID-1 backup using those two hard disks. I mean why would I need to re-install operating system to add RAID setup?

  Read the article

• Galaxy Tab 3 producing continuous LightSensor error in LogCat

  - by Richard Tingle

  I am using a Galaxy Tab 3 as a test device for writing an android app. As such I'm interested in the output of the LogCat which is being filled with these error level messages. The device itself appears to work correctly, apps which rely on the light sensor correctly respond to it and the number in the error itself goes down if the light sensor is obscured. If I wasn't using it to develop apps I wouldn't even be aware of the issue but I believe it is an issue with the device itself not my app: simply plugging the tab 3 into the computer and using Eclipse - ADT to look at the LogCat without any app running leads to these errors being shown. I know I could filter the LogCat to ignore these errors but inconvenience aside; they concern me. A sample of the log cat is below (it generates errors continuously). This is on verbose so it includes some debug level (D/) messages as well as the error level messages (E/). How can I correct the device to no longer generate these errors. 06-11 10:08:45.789: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:45.992: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:46.195: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:46.398: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:46.601: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:46.804: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:47.007: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:47.210: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:47.414: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:47.617: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:47.820: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:48.023: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:48.039: D/dalvikvm(15201): GC_CONCURRENT freed 1947K, 17% free 16973K/20359K, paused 13ms+13ms, total 50ms 06-11 10:08:48.226: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:48.429: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 13 06-11 10:08:48.632: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 13 06-11 10:08:48.632: D/STATUSBAR-NetworkController(472): refreshSignalCluster: data=0 bt=false 06-11 10:08:48.835: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:49.039: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:49.242: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:49.445: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 13 06-11 10:08:49.632: D/STATUSBAR-NetworkController(472): refreshSignalCluster: data=0 bt=false 06-11 10:08:49.648: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:49.851: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 13

  Read the article

• Display is slightly blurry on (native) 1920x1080 resolution

  - by Martin Tuskevicius

  I have a computer monitor that is approximately 23" in size. Its native resolution is 1920x1080, and Windows 7 will not allow it to be any higher. However, I cannot make the resolution a little lower as well. When I right-click on my desktop and select 'Screen resolution,' the vertical slider has only two options: 1920x1080 and 1280x720. There are no real problems that I am having besides the fact that the image is slightly blurry. I can easily make things out and see them, but I definitely feel that the image is not as clear as it could be. My graphics card is ATI Radeon HD 5450 and it has the latest graphics drivers installed. I've tried playing around with the AMD VISION Engine Control Center to see if I can change an option to make the image clearer, but I had no luck. I did find one odd thing, though. When I lowered the refresh rate from 60Hz to 50Hz, the image kind of "zoomed in" but it also became perfectly clear like I would expect it to look. The problem is that when I use 50Hz, the image zooms in a little on the center and I lose maybe an inch and a half of the screen (I do not see the bar at the top of applications, I do not see the Windows taskbar thing, etc). I figured if I could somehow zoom in so that the entire image fills the screen (not the slightly cropped version) then I would have the perfectly crisp image of 50Hz, and also the uncropped image of 60Hz. However, upon zooming in, the image began to look blurry again just like it did with 60Hz. So I am at a loss here. I do not know how to make the image look as clear as it should. I have the latest drivers (I updated them today) and I know that my monitor supports the resolution that I am trying to use. Has anybody experienced something like this before? I'd really appreciate any input - thanks! Update: I have figured out how to make the display look crisp! I set it to the 50Hz option, and then I changed the scaling through the monitor itself, rather than software. Now, however, I am finding that games look pretty bad because since it is clear, the lower quality really becomes apparent. I cannot run new games at 1080p, so I run them at the lowest resolution possible (1280x720, since it is the only other option offered, as I have mentioned). So I am wondering, is there a way to have Windows display more resolution options?

  Read the article

• Concerning persistence size in the Linux Live Creator

  - by user63085

  Message : Hello everyone! I have ,for the last several months, used the Linux Live USB Creator which it is a very useful app to make portable OS on to flash drives. I mostly use this application to test and try out new OS's as they are released, before I decide to make a hard disk installatio on to the computer. In many cases, the application developers will allow the “persistence” feature in the flash-drive-installed OS, which is just another way of saying that after multiple boot-ups and shutdowns, all the changes made to the OS will be saved in the flash-drive. But I have a question about the limit of the Persistence size in Linux Live USB Creator (currently version 2.6). I install Super OS 10 on to a partition on my external drive which has 30 GB. I wanted to reserve 10 GB for the persistence so that I can install more applications and space will not run out as I update the installed applications or when I do system updates. But why is it that only 3950 MB can be put for persistence? It would be great if, when desired, as much more persistence space could be set aside so that the space will not run out soon. Also, as I have installed the OS on a 30 GB drive, I tried to see how much space is left. But it seems only the remaining of the Persistence space is displayed when I click on the File System folder. For example, after I have just installed it now, there is 3.5 GB of free space. Where can I access the remaining 26 GB or so drive space which is in the same drive? How do I access it Sir?? It would be helpful if any one could explain and help me with this. Most importantly, it would be a big relief if the persistence can be somehow expanded by a work-around so that I can continue using my SuperOS 10.04 (now heavily customized) OS, which unfortunately has just over 576 MB of space left now, after I removed OpenOffice.org and installed the Libre Office earlier today. This is what remains from the maximum allowable 3950 MB of space for persistence at set-up. Thanks in advance!

  Read the article

• Recovering damaged external hard disk by installing internally

  - by nfarshchi

  I had a 1TB Western Digital (My book series) 3.5" USB3. One day, the SATA to USB3 converter board was damaged and has not worked since. I decided to open the cover and use the HDD as an internal HDD. When I attached the HDD to my PC and booted up in Windows, it asked me which type of ????? I want to use "MBR or GBR" (I dont remember the exact question) I chose MBR and Windows gave me a 1TB empty Hard drive. I tried to recover with recover my files and some other recovery programs but no success. Some one told me that you should choosed GBR instead of MBR . How can I do that now? Another guy told me that the SATA to USB3 converter board is coded to save data on HDD and you can not use them internally without losing data, and I should find another SATA to USB3 board (exact same). It is impossible to find because they are not produced any more. Please help me to find a solution to bring back my data. UPDATE I have 1TB WD "Mybook" USB 3. the board that convert sata to usb3 was damaged. so when the HDD was in the box computer did not recognize it. I opened the box and remove HDD to use it internal. after connecting to my PC windows showed me one massage that I had two choice MBR or GPT I choosed MBR one and windows gave me 1TB empty new volume. I tried many recovery software to recover my data but no success. I brought it to one expert recovery company and they told me the converter board (SATA to USB3) make some encryption on data and with out that board you cannot recover any thing. so I bought another empty WD box and put the HDD inside but even after that also there is no file. I tried to recover again in this state but no success. so I have some unanswered question. does this converted boards make any password or encryption? if yes how can I solve it? does using many recovery programs affected my data? any suggestion or solution for bring back my data? I had use recovery programs such as : recover my files , EaseUS data recovery, easy recovery, test disk, Ontrack easy recovery . Note: when I was using test disk it asked me to choose which partition table I want to use. as it was I choose NTFS, does this made any change on data?

  Read the article

• How to find the process(es) which are hogging the machine

  - by Aaron Digulla

  Scenario: All of a sudden, my computer feels sluggish. Mouse moves but windows take ages to open, etc. uptime says the load is 7.69 and raising. What is the fastest way to find out which process(es) are the cause of the load? Now, "top" and similar tools isn't the answer because they either show CPU or memory usage but not both at the same time. What I need is the single command which I might be able to type as it happens - something that will figure out any of System is trying to swap 8GB of RAM to disk because process X ... or process X seeks all over the disk or process X uses 400% CPU" So what I'm looking for is iostat, htop/atop and similar tools run into one with an output like this: 1235 cp - Disk trashing 87 chrome - Uses 2&nbsp;GB of RAM 137 nfs_bench - Uses 95% of the network bandwidth I don't want a tool that gives me some numbers which I can analyze but a tool that tells me exactly which process causes the current load. Assume that the user in front of the keyboard barely knows how to write "process", but the user is quickly overwhelmed when it comes to "resident size", "virtual memory" or "process life cycle". My argument goes like this: A user notices a problem. There can be thousands of reasons ... well, almost :-) The user wants to know the source of the problem. The current solutions give me lots of numbers, and I need to know what these numbers mean. What I'm looking for is a meta tool. 99% of the data is irrelevant to the problem. So what the tool should do is look for processes which hog some resource and list only those along with "this process needs a lot of CPU, this produces many IRQs, this process allocates a lot of RAM (and it's still growing)". This will be a relatively short list. It will be much more simple for someone new to this to locate the culprit from this list than from the output of, say, htop which gives me about 5000 numbers but requires me to fold multi-threaded processes myself (I have 50 lines which say VIRT 2750M but only 16 GB of RAM - the machine ought to swap itself to death but of course, this is a misinterpretation of the data that can happen quickly).

  Read the article

• Can't install .NET framework 4.0 on Windows XP professional version 2002 SP3 (OS bug?)

  - by that guy

  .NET framework 4.0 install fails on Windows XP professional version 2002 SP3: I tried to run setup using "run as..." to make sure the admin rights are used ("protect my computer..." tick was deselected of course). I tried everything: installing using online/offline setup, windows update. install goes a little and then "rolls back" and says: Installation did not succeed .NET Framework 4 has not been installed because: Fatal error during installation. for more information about this problem, see the log file. the full log: http://pastebay.net/1433771 Any ideas? EDIT1: I have found this in the log: "BlockIf: You must install the 32-bit Windows Imaging Component (WIC) before you run Setup. Please visit the Microsoft Download Center to install WIC, and then rerun Setup...." So I found it, and launched "wic_x86_enu.exe" - but it said: WIC Setup error Newer version of update is already on the system. I have already installed: .NET framewrok 2.0 SP2 .NET framewrok 3.0 SP2 .NET framewrok 3.5 SP1 but I need 4.0 . EDIT2: another attempt and it's log. (this time better copy of log file): http://pastebin.com/gmGfbM9a (copy to notepad and save as .htm and open with internet browser). I have tried all the solutions I could find - and nothing helped. I have found something weird: when I formatted the hard drive and installed windows xp again - the .NET framework 4.0 installed ok, but when I plugged my 100Mbit internet cable - the operating system kind off "locked itself" and the bug returned - I could no longer install .NET framework 4.0 again. There was no reason for that to happen, for example I have windows server 2003 in local network, but I don't have active directory enabled on it or anything like that - the server just has some folders shared and thats all (all server's "features" are default). I had the second pc with the same problem - with XP on it too. This seems like the bug of Operating System to me. I couldn't find what was causing the problem. After many days I gave up: backuped everything, formatted HDD and installed Windows 7 professional 64bit. .NET framework 4.0 installed with no problem on it.

  Read the article

• TrueCrypt partition will no longer mount

  - by sparkyuiop

  I am hoping for some advice to help me out of my situation, with luck. I have a computer running Windows 7 Ultimate x64 with 3 hard disks installed. On my 2TB hard disk 2 (non-system disk) I have 4 partitions. One is for music, another for video, a downloads partition and a 500GB RAW Truecrypt encrypted partition / volume that I had setup to mount with 4 photographs used as keyfiles. The 4 photographs are located in my 'Documents' partition which is one of four partitions on my 1.5TB hard disk 1 (non-system disk) When I setup the disk encryption I did not (I'm 99% sure) create a password, I only used the 4 photograph keyfiles to mount the volume. Recently my 1TB hard disk 0 (system / boot) started to fail so I decided to replace it. I was going to clone the old disk to a new disk but decided that a fresh installation would be more beneficial. Once I had transferred all the required 'User Data' from my old hard disk 0 (C: disk) I discarded it. I reinstalled Truecrypt, pointed to the partition, selected my 4 keyfiles photographs and I mounted my encrypted volume with no issues. In fact I mounted it several times after re-installing Windows and after reboots. Now all of a sudden when I try and mount it I get the message "incorrect keyfile(s) and/or password or not a Truecrypt volume". Now I am not sure why this happened as I do not recall exactly what I did between last mounting the volume successfully and it not mounting. Here are some of the possible things I may have done to cause it to stop working but I am at a loss as to where to start to try and resolve the problem. 1. I had swapped the drive letters to a preferred order. 2. I possibly swapped the physical SATA connectors on the mainboard. 3. I enabled 'Hot Plugging' for the two non-system hard disk SATA ports and the DVD SATA port in the BIOS. I have tried changing the encrypted partition drive letter as suggested in another post but this does not help. On my old system the encrypted drive was drive "X". I have about tried it with all the other free drive letters but alas nothing changes. I do not recall what drive letter was allocated to the encrypted partition before I changed them all. I have not tried to change the letter back to what it possibly was to start with as I am happy with the current layout. I will try this is anyone thinks it would be worthwhile though. I do hope I have managed to convey my situation in an understandable manner and live in hope someone could help me recover years of personal files. Thank you very much for taking the time to read my post and for any suggestions you may offer. Regards Phillip Thorne (UK) Anyone???

  Read the article

• OEM sound card with no drivers or support

  - by randy

  I thought my sound card was going out so I bought a sound card online. Everything seemed to work ok, I do have sound. But after a few months, I noticed the extra software that downloaded with the sound card drivers didn't work. I ended up contacting creative and after a month of e-mail support, they asked for the serial number and/or model number. Their reply back was I had purchased an OEM sound card and they could not provide support for that, and informed me that that is why their drivers and software didn't work. They informed me that I had to contact the company that distributed the sound card and install their software. Is there anything I can do to find out who distributed this sound card, or is there anything I can do to get other features to work? I have 4 speakers and a sub but only 2 speakers produce sound. The only control I have is the volume. Creative's driver update program will find my sound card, download updates and even added software, but if I try to click on a downloaded program like Creative's Toolbox or Media Center, I get an error that it cannot find the devise. That is why I contacted creative in the first place. EDIT Thanks for the responses everyone. Here's an update. I thought I'd go thru my old computer stuff for my classes at school. I have a lot of old stuff saved, boxes and cables and stuff. I found the box the sound card came in. It looks like a box you'd buy at the store, like Best Buy or CompUSA. I worked with creative for such a long time, it went past the point of being able to return it to the junk online store this shipped from. The box did have an install CD, so I thought I'd start over to reinstall the drivers and software that shipped with the card. I noticed that the install would uninstall a program, then reinstall it. so I thought things were working out. But no good. Everything still works but the programs were still bad. I'd get an error trying to load them - not found. I'll look on the card the next time I get a chance and see if I can spot any kind of name on it.

  Read the article

• windows 7 virtual wireless adapter keeps going to sleep

  - by conners

  Just a quick question that I can't see mentioned anywhere online. I have a Windows 7 box configured like these guys recommend http://www.itgeekdiary.com/windows-7-as-an-wi-fi-access-point/ simply so that I can have my Windows 7 box as a wifi access point or a wifi emitter. It's also called a Microsoft Virtual WiFi Miniport Adapter. But it powers off and shuts down automatically and stops working. Basically everything works as intended and then - well -it will stopped working when I am not at the Windows 7 PC for a long time. The problem seems to be that every time my PC goes to "power save / sleep" and in the morning the Windows 7 machine "wakes" but blooming heck the wifi has stopped and you have to power cycle the PC (which is very uncool). When I power Cycle I have to do the following as administrator C:\Windows\System32\netsh.exe wlan start hostednetwork I then tried a gazllion things involving services and power management and eventually discovered that if I run the following commands as administrator it will be ok (for a bit) but every 3rd ot 4th time I try this "trick" it simply fails. the trick that seems to work 3 out of 4 times (i.e. "most" of the time) C:\Windows\System32\netsh.exe wlan stop hostednetwork C:\Windows\System32\netsh.exe wlan start hostednetwork But why does this only work "some" of the time? What else I did by myself: on every manage adapter properties (that relates to the wifi) I right clicked [configure] [power management] /disabled/ "allow the computer to power off to save power" <- this made no difference Also (and this is a bit annoying) there is no system tray app/GUI for the Microsoft Virtual WiFi Miniport Adapter output signal ... none... so (lame as it sounds) the ONLY way I can check if it's on is to physically go to another device and SCAN.. lame so my question can probably be solved by any of the following: a) can I stop Windows 7 sleeping this wifi when the machine sleeps b) can I force Windows to force wake this process on wake? if so how? c) what is the service / process REALLY called and how do I restart it if it crashes d) how can I flush the wifi properly rather power cycle the host machine e) anyone have a link to an program or app that can sit in the system tray that shows windows 7 wifi hotspot emission status (on/off/etc etc) Since I am a programmer I can easily write a vbs script / windows exe to fix this (and I will share this solution) and the gui problem if I can work out the actual service that is running that netsh stops/starts

  Read the article

• netbook intel GMA 3150 external monitor 1920x1080 flicker problem

  - by seyenne

  Dear all, i recently purchased a acer netbook (apsire one d260). It runs flawlessly. Yesterday I bought a samsung 23" TFT with a native resolution of 1920x1080. According to the information found in the internet and my local computer dealer, the intel chipset can handle the native resolution of the monitor. However, this is only partly the case. I use the VGA cabel to connect, the monitor instantly switches to the native resolution and now the problem: Occasionaly, especially the first 2 hours after booting up, I have a flickering all over the screen, sometimes the entire screen is shaking and spinning around like crazy. I figured out, that lowering the resolution avoids the flicker but this helps only for some time. I can rule out that it's the monitor's problem since I found no issues with another notebook. Right now, I have no problems with the netbook, for about 30 minutes I didn't experience any issues... But I don't know for how long, it occurs without warning :-) I'm worried that if I would bring the netbook back to the dealer and explain my problem, after testing it on an external screen in the local shop, everything works just fine... And I won't get helped with the problem because I can't prove it. (I'm currently in Thailand and over here, customer service is nothing like back home in Germany) What can I do? Is this a driver related issue? (I installed the latest GPU driver) Is it because of the VGA cable? (But why does it work sometimes without any problems and with no issues on the other notebook) I monitored the GPU/CPU temperature, nothing changes really over time..Can it simply be a faulty GPU and is a replacement justifiable? I'm really stressed now because for the time I'm writing, the flickering didn't occur...but for sure, soon or later it will happen again.. I Forgot to mention, the problem also happens if the netbook runs on battery, unplugged. So the only hardware that is plugged is the TFT screen. ...........and here it comes again, flickering has just begun. NEED HELP! Thank you all for reading through this and giving any suggestions if possible. Cheers

  Read the article

• Windows 7 immediately disconnects a USB drive

  - by Daniel Saner

  I am having a problem with Windows 7 x64 consistently disconnecting one specific USB mass storage drive immediately after it is connected. The drive in question is a Cowon C2 digital music player which works in standard mass storage controller mode (i.e. no device-specific drivers needed/available). When I connect the player, Windows plays the "USB connect" sound and the device appears (under its correct name) in the device manager, but it never appears as a drive. The player itself displays "USB Connected" for a split-second before reporting that it has been disconnected again. Since the player, by design, reboots after it has been disconnected, Windows plays the "USB disconnect" sound before restarting the whole cycle once the player has powered back on. I am connecting the player through an Intel X79 Chipset motherboard (Gigabyte GA-X79-UD3) to Windows 7 Pro 64-bit. The player used to work fine the first few times I connected it, showing up as an external drive; it only recently stopped working. It is not a problem with the player, since it works fine when connected to another computer, even such running the exact same operating system. It is also not a problem with the USB controller, since the issue is the same on both the Intel USB 2.0 and the Fresco Logic FL1009 USB 3.0 controller ports. I have also not had the problem with any other drive so far. Among the things I have tried so far: Disabling USB legacy mode in BIOS Disabling energy-saving power down for all USB controllers in Windows' device manager Removing and reinstalling Windows' USB mass storage driver Removing and reinstalling Intel and Fresco Logic USB controller driver Restoring the player to factory defaults None of these made a difference. Again, the player used to work fine on the exact same system just days ago; I didn't install any new hardware or drivers on it since then. I would be very grateful for any hints on what else to try. Edit: Here is another new hint; I found out that when I connect the drive before booting Windows, it is available in Windows Explorer as it should, and does not automatically disconnect. If I remove and reconnect it though, the infinite connect/disconnect-loop starts anew.

  Read the article

• Remote Debian System Preventing Logon

  - by choobablue

  I have a dozen or so single board computers on a network running Debian (squeeze) and access them via ssh (ssh server is dropbear). To give an idea of the hardware of these computers they're 1.2 GHz x86 processors, 1GB of RAM and 4GB flash drives formatted as ext2 (I avoided ext3 to prevent the added flash write stress from journaling), there is also a swap partition on the drive. Normally the setup I'm using works great and I can access all the computers. Every once in a while one will prevent access. What happens is I try to connect via ssh (putty) and it gives me the login prompt, I enter the username and password and it responds 'Access Denied' and it will also refuse any public key in ~/.ssh/authorized_keys. The credentials are correct as they worked previously. The computer responds to pings and putty recognizes the server public key, which implies to me the system is still running. Restarting the server fixes the problem and I can log in again. (I tried a temporary fix of putting shutdown -r now in the root crontab but this doesn't seem to reliably be run once the hang happens) Once I restart however there doesn't seem to be any information in any of the system logs to indicate what happened, the logs are simply empty for that time period, as if the system had crashed. There is some custom software running on the system which appears to stop working (which is why I wanted to ssh to begin with). I'm assuming that this program is the source of the problems but I'm unsure of how it would cause it and how to debug what is happening. The most likely explanation I can think of is that there is a memory leak in the other program that then prevents dropbear from spawning a new login shell (and crontab from executing shutdown) as there is not enough free memory. But looking at memory usage of the other (working) computers there doesn't seem to be any meaningful increase in memory to indicate a leak (unless it's a very big, fast acting and rare leak). I would think that when the OS ran out of memory it would restart the system or kill processes (the Linux kernel restarts right?). The other thing I wonder about is if the fact that they are running off a flash drive could have some effect, especially the swap partition (which I think I should remove to prevent wear of the flash), but the flash drives are young (~1 month) and I don't think that wear would be a factor yet. Does anybody have an idea of what could cause these symptoms, if it could be done by a memory leak, or something else I haven't thought of. And does anybody know of a method to try to debug the problem and find out more information about what's going wrong?

  Read the article

• Internet Pings but Does Not Load

  - by t3techcom18

  From what I've been seeing and been doing my research for the past two days, many people have been having the same issues throughout the years, however, this is the first time I've encountered this issue and many of the specific workarounds or fixes have not worked for me. I've been trying to work through this for 24 hours straight now, but to no avail so many thanks to those that can help. On Monday night, got home from work; surfing the internet for half an hour, everything was fine as always. Just after half an hour, my Internet got very sluggish and then it died completely. I thought it might have been the an update I just put through in terms of Windows Update that said was a critical update for MSE, as the same thing happened a few years ago. I did a System Restore to two different dates that were in the past two weeks, nothing. Uninstalled MSE and disabled Windows Defender and the Windows Firewall: Nothing. Reset IE Options, Reset Winsock, Dumping DNS, many of the other command prompt screens to reset items: Nothing. Reset the modem: Nothing. What DID work, however, was a ping test to Yahoo. The ping test worked, saying all four packets was recieved, yet nothing else popped up. LAN and CenturyLink said everything worked on their end and that everything was connected properly, as well as the speeds working fine. CenturyLink said in their notes that they thought Port 80 was blocked. I went and put in the Firewall to allow Port 80 but it didn't make any difference whatsoever. I remembered I had a spare modem laying around and I switched them up, both modem and the cords - nothing. I then hooked it up to my netbook to see if that would work, as it usually does - connection didn't work there either. Like I said, it's been about 24 hours now and this is increasingly frustrating, as I've tried all solutions (While browsing through 10 search results pages on my phone) suggested and still nothing. Any suggestions and tricks would be greatly appreciated! Here's my specs: Windows 7 32-bit Home Premium Intel Core 2 Duo 3.14 Ghz 4 GB Kingston DDR2 RAM eVGA nForce 750i SLI eVGA GeForce GTX 560 Ti FPB ISP: CenturyLink No router Modem: CenturyLink 660 Series Hardwired connection PLEASE NOTE: This is the only computer I have (Like I said, the netbook solution didn't work), so downloading programs and such is not an option til I get to other computers somewhere else, like right now. Unless someone knows of a way of copying/pasting a file in Windows and then transferring said info to an Android smartphone, this is gunna take a while haha. Patience is requested.

  Read the article

< Previous Page | 724 725 726 727 728 729 730 731 732 733 734 735  | Next Page >