Search Results

Search found 22277 results on 892 pages for 'multiple addresses'.

Page 733/892 | < Previous Page | 729 730 731 732 733 734 735 736 737 738 739 740  | Next Page >

• (13) Permission denied on Apache CGI attempt

  - by ncv

  I have recently upgraded my Apache2 server, and am now unable to run a CGI app. My logs are showing (13) Permission denied unable to connect to cgi deamon after multiple tries I understand that the error message means Apache is being denied some permission to some file, and I'm stumped as to how to track down and solve the problem. Is the file mentioned in the error message truly the blocked file? Or might the problem be caused by some other needed file? The .cgi file is right where it has always been, under /usr/share. The file ownership (root) and permissions (world readable/executable) are the same as they have always been for the file and its ancestors. The SELinux file labels are unchanged. The SELinux audit log shows no denial associated with Apache nor the CGI program. In case of a donotaudit condition, I enabled audit, but still saw nothing. I switched SELinux into permissive mode briefly, to no avail. I even tried restarting Apache while in permissive mode. This did not solve the problem. Any suggestions on how to solve this problem? I'm tempted to just revert to the older Apache.

  Read the article

• Coffee spilled and went inside CPU...computer not starting

  - by Harpreet

  Today coffee got spilled over my table, and some of it (very less) reached the CPU placed under the table. I think little bit of it got inside the CPU through the front face of the CPU. As that happened the fan started running very fast and made noise. I tried to restart to see if it becomes fine, but the computer didn't start again. First it gave an error of "Alert! Air temperature sensor not detected" and didn't start. Next I tried again multiple times of starting the computer but then it gave some memory error. I was not able to start the computer. Incase there's a problem in hard disk or something related to memory, is there any way we can extract our work or data? I am scared if I am not able to extract my work in case some problem occurs like that. What options would I have? Help! EDIT: I have attached the photo here and you can see the area spilt in red circle. The hard drive electronics have been affected and internal speaker may also have been affected. Any advise on cleaning and if hard drive can work? EDIT 2: Are there any professional services offered to extract data from blemished hard disk, like this one, in case I am not able to run it personally?

  Read the article

• pfSense router on a LAN with two gateways

  - by JohnCC

  I have a LAN with an ADSL modem/router on it. We have just gained an alternative high-speed internet connection at our location, and I want to connect the LAN to it, eventually dropping the ADSL. I've chosen to use a small PFSense box to connect the LAN to the new WAN connection. Two servers on the LAN run services accessible to the outside via NAT using the single ADSL WAN IP. We have DNS records which point to this IP. I want to do the same via the new connection, using the WAN IP there. That connection permits multiple IPs, so I have configured pfSense using virtual IP's, 1:1 NAT and appropriate firewall rules. When I change the servers' default gateway settings to the pfSense box, I can access the services via the new WAN IPs without a problem. However, I can no longer access them via the old WAN IP. If I set the servers' default gateway back to the ADSL router, then the opposite is true - I can access the services via the ADSL IP, but not via the new one. In the first case, I believe this is because an incoming SYN packet arrives at the ADSL WAN IP, and is NAT'd and sent to the internal IP of the server. The server responds with a SYN/ACK which it sends via its default gateway, the pfSense box. The pfSense box sees a SYN/ACK that it saw no SYN for and drops the packet. Is there any sensible way around this? I would like the services to be accessible via both IPs for a short period at least, since once I change the DNS it will take a while before everyone picks up the new address.

  Read the article

• Trouble cloning a Macbook Pro hard drive

  - by Mirko Froehlich

  I am trying to upgrade the 250GB hard drive in my MacBook Pro (early 2008 model) to a 750GB drive. I have connected the new drive via an external USB enclosure. The drive is recognized fine, I can format it, etc. However, every time I try to clone the drive, I am getting Input/Output errors. Before the clone operation, I have verified both the internal and the external drive using Disk Utility, and they both check out fine. After the clone operation, the external drive shows multiple "Invalid node structure" errors: I have tried two approaches for cloning the drive: Using Disk Utility, by starting from the OSX install DVD Using Carbon Copy Cloner The outcome is the same in both cases. The Carbon Copy Cloner logs show a handful of the following types of errors: rsync: mkstemp "<... an external filename ...>" failed: Input/output error (5) rsync: stat "<... an external filename ...>" failed: Input/output error (5) The actual files affected seem to be different across different runs of the application. Before the last run, I used Disk Utility to (once more) reformat the external drive and explicitly overwrite it with zeros, but this made no difference. I also tried running a surface scan in Tech Tool Pro overnight. It got about 2/3 of the way through before I had to disconnect the drive (had to take my MacBook Pro to work), but so far it didn't report any bad blocks. Assuming it scans the drive in the same order in which blocks would be allocated during actual use, it seems like if bad blocks were to blame for the clone failures, they should have been found already (given that the source drive is only 250GB). As a last attempt, I may try SuperDuper as well, although my understanding is that it uses the same underlying rsync approach as Carbon Copy Cloner, so it's unlikely to perform any better. Are there any other things I should try before I send the drive in for a replacement? Could these problems be caused by my internal drive, even though it works fine and checks out fine in Disk Utility?

  Read the article

• Unable to remove limit on memory usage for PHP script.

  - by Jess Telford

  The Situation I am having an issue with a PHP script getting the following error message: Fatal error: Out of memory (allocated 359923712) (tried to allocate 72 bytes) in /path/to/piwik/core/DataTable.php on line 969 The script I'm running is: /path/to/piwik/misc/cron/archive.sh I am assuming the numbers are Bytes, which means that total is approximately 360MB. For all intents and purposes, I have increased the memory limits on the server well above 360MB, yet this is the number (give or take a byte) it consistently errors out at. Please note: This question is not about fixing a memory leak in the script, nor about why the script itself is using so much memory. The script is part of the Piwik archiving process, so I cannot just fix any memory leaks, etc. For more info on this script and why I am increasing the memory limit, see "How to setup auto archiving" The question Given that the script is attempting to use over 360MB of memory, which I cannot change, why does it not seem possible for me to increase the amount of memory available to php on my server? What I've tried Increasing PHP's memory_limit Given the php.ini file: php -i | grep php.ini Configuration File (php.ini) Path => /usr/local/lib Loaded Configuration File => /usr/local/lib/php.ini I have edited that file, so the memory_limit directive reads; memory_limit = -1 Restart Apache, and check the new value has stuck; $ php -i | grep memory_limit memory_limit => -1 => -1 Run the script, and get the same error. I've also tried 1G, 768M, etc, all to the same result (ie; no change). Update 22nd June: Based on Vangel's help, I have attempted to set post_max_size to 20M in combination with setting memory_limit. Again, this has no effect. Removing the memory limit on child processes of Apache I have found and edited the httpd.conf file to make sure there is no RLimitMEM directive. I then used WHM's Apache Configuration Memory Usage Restrictions to generate a restriction, which it claimed was at 1000M (and confirmed by checking httpd.conf). Both of these resulted in no change to the script erroring at 360MB. Increasing the per process memory limits of Linux The current limits set on the system: $ ulimit -m 524288 $ ulimit -v 524288 I have attempted to set both of these to unlimited: $ ulimit -m unlimited $ ulimit -v unlimited $ ulimit -m unlimited $ ulimit -v unlimited Once again, this has resulted in absolutely no improvement in my problem. My setup $ cat /etc/redhat-release CentOS release 5.5 (Final) $ uname -a Linux example.com 2.6.18-164.15.1.el5 #1 SMP Wed Mar 17 11:30:06 EDT 2010 x86_64 x86_64 x86_64 GNU/Linux $ php -i | grep "PHP Version" PHP Version => 5.2.9 $ httpd -V Server version: Apache/2.0.63 Server built: Feb 2 2011 01:25:12 Cpanel::Easy::Apache v3.2.0 rev5291 Server's Module Magic Number: 20020903:13 Server loaded: APR 0.9.17, APR-UTIL 0.9.15 Compiled using: APR 0.9.17, APR-UTIL 0.9.15 Architecture: 64-bit Server compiled with.... -D APACHE_MPM_DIR="server/mpm/prefork" -D APR_HAS_SENDFILE -D APR_HAS_MMAP -D APR_HAVE_IPV6 (IPv4-mapped addresses enabled) -D APR_USE_SYSVSEM_SERIALIZE -D APR_USE_PTHREAD_SERIALIZE -D SINGLE_LISTEN_UNSERIALIZED_ACCEPT -D APR_HAS_OTHER_CHILD -D AP_HAVE_RELIABLE_PIPED_LOGS -D HTTPD_ROOT="/usr/local/apache" -D SUEXEC_BIN="/usr/local/apache/bin/suexec" -D DEFAULT_PIDLOG="logs/httpd.pid" -D DEFAULT_SCOREBOARD="logs/apache_runtime_status" -D DEFAULT_LOCKFILE="logs/accept.lock" -D DEFAULT_ERRORLOG="logs/error_log" -D AP_TYPES_CONFIG_FILE="conf/mime.types" -D SERVER_CONFIG_FILE="conf/httpd.conf" Output of $ php -i: http://pastebin.com/EiRut6Nm

  Read the article

• Windows 7 x64 RTM USB Port Has Power But Won't Recognize Mouse/Keyboard/Anything

  - by ben

  I have an odd error that doesn't seem to fit in with any of the other odd Windows 7 x64 USB errors that have been kicked up on Google. Here we go: Uninstalled Tortoise SVN and clicked restart computer. My machine had been up for around 28 days On reboot my mouse and keyboard failed to work anymore, couldn't log in. Tried every USB port I have on my Dell 390 and the ports on my Dell 19's, nothing worked. They had power but Windows would not respond when I manipulated the keyboard/mouse. Rebooted my computer and pressed F2 to get into bios, my keyboard is working fine in bios. Keyboard and mouse work fine on other computers when using USB. Found adapters for keyboard and mouse to convert from USB to PS/2 ports, works fine. I'm actually typing this question on the same keyboard, same computer, just using PS/2 ports for my mouse and keyboard. It appears to be a Windows 7 x64 issue. Other things I have tried: Multiple other mice and keyboards, iphone, all with no luck. Each one gets power, but Windows never tries to install drivers or sees that they are connected. Uninstall and reinstall all USB drivers. Drives uninstall and reinstall fine and report no errors in Control Panel. In Power Management I disallow Windows from turning off USB ports to save power Installed the latest nVidia drivers for my graphics card, no change. Anyplace else I can look/try? Thanks!

  Read the article

• Windows XP: How to delete files and folders that cannot be deleted?

  - by glenneroo

  I have a backup copy of a previous Windows' Documents and Settings folder which only contains my original user and within 2 more directories: Favorites and Local Settings. When I try to delete Local Settings I get this error: When I try to delete Favorites, I get this error: I ran this in a cmd shell: attrib *.* -r -a -s -h /s ...but it did not help, nor did it return any errors/warnings. I used Unlocker v1.8.5 and LockHunter repeatedly at multiple levels to see if any files are in use, but both always say: No Files Locked. Update #1: I was able to rename the directory, which now gives me this warning before (trying to) delete: If I press Yes (or Yes to All) then I get this error: Update #2: I let chkdsk /f run which required a reboot since it's on my primary system partition. During Stage 2 scanning, I received about 40 of these: Deleting an index entry from index $0 of file 25. ...followed by: Deleting index entry cookies in index $I30 of file 37576. ...but I still get the first error dialog above when trying to delete. Update #3: Digging deeper, the 99 is the name of one of many directories located deep in here: C:\Documents and Settings.OLD\User\Local Settings\Application Data\Microsoft\Messenger\[email protected]\SharingMetadata\[email protected]\DFSR\Staging\CS{D4E4AE55-B5E2-F03B-5189-6C4DA6E41788}\ Inside each of those directories were files with names such as: 2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-Downloaded.frx I noticed that, unlike all the directories, I couldn't rename any of these files. I also noticed that the file + dir names were extremely long: Original directory = 194 characters Filenames = 100+ characters Together the length exceeds the 255-char limit which is bad and would explain the error message I posted in Update #1. Partial Solution: Rename all directories until the total path length is less than 100. Afterwards I was able to rename the .frx files, not to mention delete everything inside the Local Settings directory. This is only a partial solution because this (empty) directory is still undeleteable: C:\1\2\Favorites\Wien\What To Do.. I'm guessing because of the ".." at the end, Windows (Explorer and cmd) can't deal with it: Here is what Explorer properties shows: Any ideas?

  Read the article

• Four disks - RAID 10 or two mirrored pairs?

  - by ewwhite

  I have this discussion with developers quite often. The context is an application running in Linux that has a medium amount of disk I/O. The servers are HP ProLiant DL3x0 G6 with four disks of equal size @ 15k rpm, backed with a P410 controller and 512MB of battery or flash-based cache. There are two schools of thought here, and I wanted some feedback... 1). I'm of the mind that it makes sense to create an array containing all four disks set up in a RAID 10 (1+0) and partition as necessary. This gives the greatest headroom for growth, has the benefit of leveraging the higher spindle count and better fault-tolerance without degradation. 2). The developers think that it's better to have multiple RAID 1 pairs. One for the OS and one for the application data, citing that the spindle separation would reduce resource contention. However, this limits throughput by halving the number of drives and in this case, the OS doesn't really do much other than regular system logging. Additionally, the fact that we have the battery RAID cache and substantial RAM seems to negate the impact of disk latency... What are your thoughts?

  Read the article

• Having trouble mapping Sharepoint document library as a Network Place

  - by Sdmfj

  I am using Office 365, Sharepoint Online 2013. Using Internet Explorer these are the steps I have taken: ticked the keep me signed in on the portal.microsoftonline.com page. It redirects me to Godaddy login page because Office 365 was purchased through them. I have added these sites to trusted sites (as well as every page in the process) and chose auto logon in Internet explorer. Once on the document library I open as explorer and copy the address as text. I go to My Computer and right click to add a network place and paste in the document library address. It successfully adds the library as a network place 30% of the time. I can do this same process 3 times in a row and it will fail the first 2 times and then succeeds. It works for a little while and then I get an error that the DNS cannot be found. I need multiple users in our organization to be able to access this document library as if it was a mapped network drive on our local network. Is there an easier way to do this? I may just sync using the One Drive app but thought that direct access to the files without worrying about users keeping their files synced.

  Read the article

• KVM error with device pass through

  - by javano

  I am running the following command booting a Debian live CD passing a host PCI device to the guest as a test and KVM errors out; kvm -m 512 -boot c -net none -hda /media/AA502592502565F3/debian.iso -device pci-assign,host=07:00.0 PCI region 1 at address 0xf7920000 has size 0x80, which is not a multiple of 4K. You might experience some performance hit due to that. No IOMMU found. Unable to assign device "(null)" kvm: -device pci-assign,host=07:00.0: Device 'pci-assign' could not be initialized lspci | grep 07 07:00.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 74) I shoved an old spare NIC into my motherboard to test PCI pass through. I have searched the Internet with Goolge and found that errors relating to "No IOMMU found" often mean the PCI device is not supported by KVM. Does KVM have to support the device being "passed-through"? I though the point was to pass the device through and let the guest worry about it? Ultimately I want to pass-through a PCI random number generator, is this not going to be possible with KVM? Thank you.

  Read the article

• Assistance on setup to Connect an offsite server to the LAN via RRAS VPN - Server 2008 R2

  - by Paul D'Ambra

  I have an office LAN protected using a Zyxel Zywall USG 300. I've set up an L2TP/ipsec VPN on that which accepts connections using a shared secret and I've tested this from multiple clients. I have a server offsite and want to set up RRAS to use a persistent connection to the VPN so that it can carry out network jobs even with no one logged in (I'm using it for Micorosft DPM secondary backup). If I create a vpn as if I were setting up a users laptop it can dial in no problem but if I set up a demand dial interface in RRAS it errors. I enable RRAS ticking only demand dial interface (branch office routing) Select network interfaces, right click and choose new demand dial interface Name the VPN ToCompany Select connect using VPN And then L2TP as the vpn type enter the IP address (double-checked for typos!) select Route IP packets on this interface specify static route to remote network as 10.0.0.0/24 with metric of 1 add dial out credentials (again double checked for typos and confirmed with other vpn connections click finish now I right-click on the new interface and choose properties and then the security tab I change Data encryption to optional select only PAP for Authentication (both as per manufacturer of Zywall) click advanced settings against type of vpn and set shared secret then I select the new interface, right-click and choose connect this dials and then errors with either 720 or 811 as the error codes. However, if I create a VPN by going to Network & Sharing center and setting up as if I was creating a VPN from my laptop to the office (say) it dials successfully so I know the VPN settings are correct and the machine can connect to the VPN. Suggests very strongly the problem is how I'm setting up RRAS. Can anyone help?

  Read the article

• Linux - real-world hardware RAID controller tuning (scsi and cciss)

  - by ewwhite

  Most of the Linux systems I manage feature hardware RAID controllers (mostly HP Smart Array). They're all running RHEL or CentOS. I'm looking for real-world tunables to help optimize performance for setups that incorporate hardware RAID controllers with SAS disks (Smart Array, Perc, LSI, etc.) and battery-backed or flash-backed cache. Assume RAID 1+0 and multiple spindles (4+ disks). I spend a considerable amount of time tuning Linux network settings for low-latency and financial trading applications. But many of those options are well-documented (changing send/receive buffers, modifying TCP window settings, etc.). What are engineers doing on the storage side? Historically, I've made changes to the I/O scheduling elevator, recently opting for the deadline and noop schedulers to improve performance within my applications. As RHEL versions have progressed, I've also noticed that the compiled-in defaults for SCSI and CCISS block devices have changed as well. This has had an impact on the recommended storage subsystem settings over time. However, it's been awhile since I've seen any clear recommendations. And I know that the OS defaults aren't optimal. For example, it seems that the default read-ahead buffer of 128kb is extremely small for a deployment on server-class hardware. The following articles explore the performance impact of changing read-ahead cache and nr_requests values on the block queues. http://zackreed.me/articles/54-hp-smart-array-p410-controller-tuning http://www.overclock.net/t/515068/tuning-a-hp-smart-array-p400-with-linux-why-tuning-really-matters http://yoshinorimatsunobu.blogspot.com/2009/04/linux-io-scheduler-queue-size-and.html For example, these are suggested changes for an HP Smart Array RAID controller: echo "noop" > /sys/block/cciss\!c0d0/queue/scheduler blockdev --setra 65536 /dev/cciss/c0d0 echo 512 > /sys/block/cciss\!c0d0/queue/nr_requests echo 2048 > /sys/block/cciss\!c0d0/queue/read_ahead_kb What else can be reliably tuned to improve storage performance? I'm specifically looking for sysctl and sysfs options in production scenarios.

  Read the article

• vconfig created virtual interface and trunking - is the the interface untagged or tagged for that VLAN ID?

  - by kce

  I am trying to setup an additional VLAN on our Debian-based router/firewall (which exists as a virtual machine on Hyper-V), our core switch (an HP Procurve 5406) and a remote HP ProCurve 2610 that is connected via a WAN Transparent Lan Service (TLS) link. Let's work backwards from the network edge: The Debian server has an external connection attached to eth0. The internal interface is eth1, which is connected directly from our Hyper-V host to the 5406. The port that eth1 is attached to is setup as Trk12. The 2610 is attached to Trk9 (which trunks a whole slew of VLANs - Trk9 is our TLS head). I can successfully ping the management IP addresses for my VLAN from both switches but I cannot ping, from either switch, the virtual interface for my new VLAN on the Debian-base router and firewall. The existing VLAN works fine. What gives? The port eth1 is attached to is a trunk, the existing VLAN (ID 98) is untagged on the trunk, the new VLAN (ID 198) is tagged. VLAN 198 is tagged on Trk9 on the 5406 and on the 2610. I can ping the other switch's management IP (10.100.198.2 and 10.100.198.3) from the other respective switch. That leg of the VLAN works - however I cannot communicate with eth1.198's 10.100.198.1. I feel like I'm missing something elementary but what it is remains illusive to me. I suspect the issue is with the vconfig created eth1.198. It should pass the tagged VLAN 198 packets correct? But they cannot seem to get any further than the 5406. Communication on the existing VLAN 98 works fine. From the Debian box: eth1: eth1 Link encap:Ethernet HWaddr 00:15:5d:34:5e:03 inet addr:10.100.0.1 Bcast:10.100.255.255 Mask:255.255.0.0 inet6 addr: fe80::215:5dff:fe34:5e03/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12179786 errors:0 dropped:0 overruns:0 frame:0 TX packets:20210532 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1586498028 (1.4 GiB) TX bytes:26154226278 (24.3 GiB) Interrupt:9 Base address:0xec00 eth1.198: eth1.198 Link encap:Ethernet HWaddr 00:15:5d:34:5e:03 inet addr:10.100.198.1 Bcast:10.100.198.255 Mask:255.255.255.0 inet6 addr: fe80::215:5dff:fe34:5e03/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1496 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:72 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:3528 (3.4 KiB) # cat /proc/net/vlan/eth1.198: eth1.198 VID: 198 REORDER_HDR: 0 dev->priv_flags: 1 total frames received 0 total bytes received 0 Broadcast/Multicast Rcvd 0 total frames transmitted 72 total bytes transmitted 3528 total headroom inc 0 total encap on xmit 39 Device: eth1 INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 EGRESS priority mappings: # ip route 10.100.198.0/24 dev eth1.198 proto kernel scope link src 10.100.198.1 206.174.64.0/20 dev eth0 proto kernel scope link src 206.174.66.14 10.100.0.0/16 dev eth1 proto kernel scope link src 10.100.0.1 default via 206.174.64.1 dev eth0 # iptables -L -v Chain INPUT (policy DROP 6875 packets, 637K bytes) pkts bytes target prot opt in out source destination 41 4320 ACCEPT all -- lo any anywhere anywhere 11481 1560K ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 107 8058 ACCEPT icmp -- any any anywhere anywhere 0 0 ACCEPT tcp -- eth1 any 10.100.0.0/24 anywhere tcp dpt:ssh 701 317K ACCEPT udp -- eth1 any anywhere anywhere udp dpts:bootps:bootpc Chain FORWARD (policy DROP 1 packets, 40 bytes) pkts bytes target prot opt in out source destination 156K 25M ACCEPT all -- eth1 any anywhere anywhere 215K 248M ACCEPT all -- eth0 eth1 anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- eth1.198 any anywhere anywhere 0 0 ACCEPT all -- eth0 eth1.198 anywhere anywhere state RELATED,ESTABLISHED Chain OUTPUT (policy ACCEPT 13048 packets, 1640K bytes) pkts bytes target prot opt in out source destination From the 5406: # show vlan ports trk12 detail Status and Counters - VLAN Information - for ports Trk12 VLAN ID Name | Status Voice Jumbo Mode ------- -------------------- + ---------- ----- ----- -------- 98 WIFI | Port-based No No Untagged 198 VLAN198 | Port-based No No Tagged

  Read the article

• Windows 2012 RDS Temporary profile for Administrator

  - by Fabio

  I've configured a Windows 2012 RDS Farm with two virtual servers (VMWare - each one on a different ESX server). Both servers have Licensing, Web Access, Gateway, Connection Broker and Session Host roles. High Availability is set up and it works fine. Remote Apps are working and even Windows XP clients have access to the web interface. User profile path is \vmfiles1\UserProfileDisks\App\ and almost everyone has full right access to it. The problem I have is that I would like to be able to access both servers at the same time with the Administrator account (console), but each time I try, the second server that I logon to give me access with a temporary profile. I tried to enable/disable multiple sessions per user and forced Admin logoff with the GPO but nothing changed. Another thing is that the server pool is not saved, so each time I restart the RDS server or I logoff from it, I have to add a server in the server manager. Do you have any idea? Sorry if my english is not perfect.

  Read the article

• VPN Client solution

  - by realtek

  I have several VPN's that I need to establish on a daily basis but from multiple workstations. What I would like to do it have either a server or vpn router that can perform this connection itself and that I can then route traffic through this device or server depending on the subnet I am trying to reach. The issue is that I only use VPN Clients to connect, so I am basically trying to achieve almost a site to site VPN but by using basically a VPN Client type connection from my network. The main VPN Client I use is the Sonicwall Global VPN Client where I initially use a Preshared Key and then it always prompts me for a username and password (not RSA key). My question is, is there any type of linux distro or even a hardware vpn router that can do this and connect to a Sonicwall device as if it were a client? I have tried pfSense which is very good but it fails to connect, probably due to a mismatch of settings. I have tried many others. Even dd-wrt on my router but it does not support whatever protocol Sonicwall uses. (I thought L2TP/IPSec) but it appears it may not be that. Any advice would be great! The other other thing I have thought of that I have not tried yet is Windows Server Routing and Remote Access but I have a feeling that won't work either. Thanks

  Read the article

• Copy/paste filtered column in Excel - error message

  - by hazymat

  Firstly I should state that I don't believe in spreadsheets; my normal mode of operation is that data should either exist in a database or a text file... However - employment requires... In short, I have filtered a worksheet by column A, and I want to copy/paste from column B to column C. Obviously I don't wish to copy/paste values from rows that were filtered-out here. The above sounds ridiculously simple, right? First I tried simply copy/pasting on the filtered worksheet. This appeared to select and copy only the filtered data, however pasting appeared to insert values into hidden/filtered rows - as you might expect. So my initial research suggests I may wish to select the filtered data and press Alt+; (that is, ALT plus semicolon), which is a shortcut key for Goto Special Select Visible. Then just copy-paste. CTRL+C correctly copies the filtered data, however when I go to paste the values into another column, it pastes into hidden rows as well. Okay, so perhaps I should also "Select Visible" on the cells I wish to paste into as well? Nope - that gives me the error That command cannot be used on multiple selections. What am I doing wrong?!

  Read the article

• How to configure mod_proxy_balancer to gracefully fail under high load

  - by bramp

  We have a system which has one Apache instance in front of multiple tomcats. These tomcats then connect to various databases. We balance the load to the tomcat with mod_proxy_balancer. Currently we are receiving 100 requests a second, the load on the Apache server is quite low, but due to database heavy operations on the tomcats, the load there is roughly 25% (of what I estimate they can handle). In a few weeks there is an event happening and we estimate that our requests will jump significant, maybe by a factor of 10. I'm doing everything I can do reduce the load on our tomcats, but I know we are going to run out of capacity, so I would like to fail gracefully. By this I mean, instead of trying to deal with too many connections which all timeout, I would like Apache to somehow monitor average response time, and as soon as the response time to Tomcat is getting above some threshold, I would like a error page displayed. This means that users who are lucky still get a page rendered quickly, and those who are unlucky get a error page quickly. Instead of everyone waiting far too long for their page, and eventually everyone timing out, and the database being swamped with queries which are never used. Hopefully this makes sense, so I was looking for suggestions on how I could achieve this. thanks

  Read the article

• Need help using a super scope

  - by Vdub

  I have a windows server 2008 r2 standard running our DCHP, DNS, and AD. also I have (3) HP Pro Curve 2510-G switches (J9280A). Right now our LAN is set up 192.168.50.2-192.168.50.254 on our sub-net (A) and another scope with 192.168.51.2-192.168.51.254 sub-net (B) both have sub-net mask of 255.255.255.0. The same server is our DNS which is 192.168.50.242 and our firewall (watchguard) is the gateway at 192.168.50.1. Right now the sub-net (B) does not have DHCP active so only sub-net (A) is giving a pool. My problem is that we are trying to have open WiFi on our network and i am assuming that i can use the sub-net (B) for that if i activate it and use sub-net (A) for our staff only. I have noticed that when i set up a static on a client pc and set it to 192.168.51.x i cannot use the DNS of 192.168.50.242 however i can use 8.8.8.8 and it works fine, i am guessing that because it is on a different sub-net? Forgive me as i am very new at this and dont know a lot. Is there easy way with the equipment i have to a accommodate wifi for hundreds of people without causing problems for our staff? (multiple same IP address assigns) I appreciate any and all info!

  Read the article

• Why I cannot copy install.wim from Windows 7 ISO to USB (in linux env)

  - by fastreload

  I need to make a USB bootable disk of Windows 7 ISO. My USB is formatted to NTFS, ISO is not corrupt. I can copy install.wim elsewhere but I cannot copy it to USB. I even tried rsync. rsync error sources/install.wim rsync: writefd_unbuffered failed to write 4 bytes to socket [sender]: Broken pipe (32) rsync: write failed on "/media/52E866F5450158A4/sources/install.wim": Input/output error (5) rsync error: error in file IO (code 11) at receiver.c(322) [receiver=3.0.8] Stat for windows.vim File: `X15-65732 (2)/sources/install.wim' Size: 2188587580 Blocks: 4274600 IO Block: 4096 regular file Device: 801h/2049d Inode: 671984 Links: 1 Access: (0664/-rw-rw-r--) Uid: ( 1000/ umur) Gid: ( 1000/ umur) Access: 2011-10-17 22:59:54.754619736 +0300 Modify: 2009-07-14 12:26:40.000000000 +0300 Change: 2011-10-17 22:55:47.327358410 +0300 fdisk -l Disk /dev/sdd: 8103 MB, 8103395328 bytes 196 heads, 32 sectors/track, 2523 cylinders, total 15826944 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc3072e18 Device Boot Start End Blocks Id System /dev/sdd1 * 32 15826943 7913456 7 HPFS/NTFS/exFAT hdparm -I /dev/sdd: SG_IO: bad/missing sense data, sb[]: 70 00 05 00 00 00 00 0a 00 00 00 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ATA device, with non-removable media Model Number: UF?F?A????U]r???U u??tF?f?`~ Serial Number: ?@??~| Firmware Revision: ????V? Media Serial Num: $I?vnladip raititnot baelErrrol aoidgn Media Manufacturer: o eparitgns syetmiM Standards: Used: unknown (minor revision code 0x0c75) Supported: 12 8 6 Likely used: 12 Configuration: Logical max current cylinders 17218 0 heads 0 0 sectors/track 128 0 -- Logical/Physical Sector size: 512 bytes device size with M = 1024*1024: 0 MBytes device size with M = 1000*1000: 0 MBytes cache/buffer size = unknown Capabilities: IORDY(may be)(cannot be disabled) Queue depth: 11 Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 0 Current = ? Recommended acoustic management value: 254, current value: 62 DMA: not supported PIO: unknown * reserved 69[0] * reserved 69[1] * reserved 69[3] * reserved 69[4] * reserved 69[7] Security: Master password revision code = 60253 not supported not enabled not locked not frozen not expired: security count not supported: enhanced erase 71112min for SECURITY ERASE UNIT. 172min for ENHANCED SECURITY ERASE UNIT. Integrity word not set (found 0xaa55, expected 0x80a5)

  Read the article

• recursive grep started at / hangs

  - by Martin

  I have used following grep search pattern on multiple platforms: grep -r -I -D skip 'string_to_match' / For example on FreeBSD 8.0, FreeBSD 6.4 and Debian 6.0(squeeze). Command does a recursive search starting from root directory, assumes that binary files do not have the 'string_to_match' and skips devices, sockets and named pipes. FreeBSD 8.0 and FreeBSD 6.4 use GNU grep version 2.5.1 and Debian 6.0 uses GNU grep version 2.6.3. On FreeBSD 6.4, last information printed to stderr was "grep: /dev/cuad0: Device busy". After this grep just idles as according to "top -m io -o total" the I/O usage of grep is nonexistent. Same behavior is true under FreeBSD 8.0, but last information sent to stderr is "grep: /tmp/.wine-0: Permission denied" on my installation. In case of Debian, last output to stderr is "grep: /proc/sysrq-trigger: Input/output error". If I check the I/O usage of grep process under Debian, it is following: root@Debian:~# iotop -bp 22439 Total DISK READ: 0.00 B/s | Total DISK WRITE: 0.00 B/s TID PRIO USER DISK READ DISK WRITE SWAPIN IO COMMAND 22439 be/4 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % grep -r -I -D skip 10.10.10.99 / Total DISK READ: 0.00 B/s | Total DISK WRITE: 0.00 B/s TID PRIO USER DISK READ DISK WRITE SWAPIN IO COMMAND 22439 be/4 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % grep -r -I -D skip 10.10.10.99 / Total DISK READ: 0.00 B/s | Total DISK WRITE: 0.00 B/s TID PRIO USER DISK READ DISK WRITE SWAPIN IO COMMAND 22439 be/4 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % grep -r -I -D skip 10.10.10.99 / ^Croot@Debian:~# What might cause this? Is there a way to view which file grep is currently processing in case lsof is not present? I'm able to use lsof under Debian and looks like the problematic file name there is "0xc6b2c230 file struct, ty=0, op=0xc0d34120". I'm not sure what this is.. I'm not able to use lsof or fstat under FreeBSD. PS: I know I could use find utility, but this is not the question.

  Read the article

• svn post-commit not performing

  - by davin

  ive been sitting on this for about 7 hours, and ive aged close to 7 years... ahhh, server admin does that to me. i have svn wired through apache2 with webdav in the usual manner (basically like http://www.howtoforge.com/setting-up-subversion-with-webdav-post-commit-hook-and-multiple-sites-on-jaunty-jackalope-ubuntu-9.04). ive had endless problems with this (i didnt on my previous ubuntu server install, although this is ubuntu 10.10): this happened, and was fixed like in the post: http://stackoverflow.com/questions/2547400/how-do-you-fix-an-svn-409-conflict-error this looks like my issue, although its not my solution: http://serverfault.com/questions/135494/apache-svn-on-ubuntu-post-commit-hook-fails-silently-pre-commit-hook-permis my commit to svn works (finally). although the post-commit hook which is supposed to svn update the working copy of the repo on the server, doesn't work. the post-commit hook itself executes, and has sudo permissions (as in the setup url above. testing with whoami somelogfile.log or sudo whoami somelogfile.log shows www-data and root, respectively), although it wont perform the svn update (sudo svn update /var/www/gameServer /var/svn/gameServer.log). similar to the serverfault url above, when i perform the exact command it does update the working copy to the latest revision, just not through the post-commit hook. an age old question that is 90% of the time a permissions issue. but in pure frustration i chmod 777 lots of stuff not to mention the fact that www-data is in /etc/sudoer so it shouldnt even need that. im collapsing in front of the screen partly out of frustration and partly out of sleepiness. any direction would be appreciated.

  Read the article

• Windows 2008 R2 Servers Sending Arp Requests for IPs outside Subnet

  - by Kyle Brandt

  By running a packet capture on my my routers I see some of my servers sending ARP requests for IPs that exist outside of its network. For example if my network is: Network: 8.8.8.0/24 Gateway: 8.8.8.1 (MAC: 00:21:9b:aa:aa:aa) Example Server: 8.8.8.20 (MAC: 00:21:9b:bb:bb:bb) By running a capture on the interface that has 8.8.8.1 I see requests like: Sender Mac: 00:21:9b:bb:bb:bb Sender IP: 8.8.8.20 Target MAC: 00:21:9b:aa:aa:aa Target IP: 69.63.181.58 Anyone seen this behavior before? My understanding of ARP is that requests should only go out for IPs within the subnet... Am I confused in my understanding of ARP? If I am not confused, anyone seen this behavior? Also, these seem to happen in bursts and it doesn't happen when I do something like ping an IP outside of the network. Update: In response to Ian's questions. I am not running anything like Hyper-V. I have multiple interfaces but only one is active (Using BACS failover teaming). The subnet mask is 255.255.255.0 (Even if it were something different it wouldn't explain an IP like 69.63.181.58). When I run MS Network Monitor or wireshark I do not see these ARP requests. What happens is that on the router capturing I see a burst of about 10 requests for IPs outside of the network from the host machine. On the machine itself using wireshark or NetMon I see a flood of ARP responses for all the machines on the network. However, I don't see any requests in the capture asking for those responses. So it seems like maybe it is maybe refreshing the arp cache but including IPs that outside of the network. Also when it does this NetMon doesn't show the ARP requests?

  Read the article

• One-To-Many Powershell Scripts

  - by Matt

  I'm trying to create a script to run as a scheduled task, which will run against multiple servers and retrieve some information. To start with, I populate the list of servers by querying AD for all servers that match a certain set of criteria, using Get-ADComputer. The problem is, the list is returned as an object, which I can't then pass to the New-PSSession list. I have tried converting it to a comma-seperated string by doing the following: foreach ($server in $serverlist) {$newlist += $server.Name + ","} but this still doesn't work. the alternative is to iterate through the list and run the various commands against each server one at a time, but my preference would be to avoid this and run them using one-to-many remoting. UPDATE: To clarify what I want to end up being able to do is using -ComputerName $serverlist, so I want $serverlist to be a string rather than an object. UPDATE 2: Thanks for all the suggestions. Between them and my original method I'm starting to wonder whether -ComputerName can accept a string variable? I've got varying degrees of success getting the list of computers converted to a comma separated string, but no matter how I do it I always get invalid network address.

  Read the article

• Web-based SVG or JavaScript Org Chart or Tree Graph Plotting Visualization API

  - by asoltys

  Hi, I'm looking to build an interactive web-based org chart for a large organization. I somewhat like the interface at ancestry.com where you can hover over people and pan/zoom around and click on different nodes to make them the root. Ideally, I'd like it if people could belong to multiple organizational entities like committees, working groups, etc. In other words the API should support graphs in general, not just trees. I'd like to be able to visually explode each organizational substructure into substituents by clicking on it, with a nice animation of the employees ballooning or spilling out so you can really interactively drill down through the organization. I found http://code.google.com/apis/visualization/documentation/gallery/orgchart.html but it looks a bit rudimentary. I know there are desktop tools like OrgPlus and Visio that can build static charts but I'm really looking for a free, web-based API with open standards-based output like SVG or HTML5 Canvas elements rather than Flash or some proprietary output. Something I can embed into a custom web application and style myself. Something interactive.

  Read the article

• What are the biggest, best CPUs that support Physical Address Extension?

  - by Giffyguy

  I'm looking for a CPU that will support PAE and fit into an LGA775 socket. This combination of technology is very much preferred for my current server hardware/software setup. My priorities in order of highest to lowest: PAE & LGA775 At least 1066Mhz FSB Largest CPU cache possible Multiple Cores if possible HyperThreading if possible Most other factors are of little-to-no consequence. I'm finding it very difficult to figure out what my options are. Intel doesn't have much useful information on PAE (since x64 is so dominant), and Wikipedia simply says that "PAE is provided by Intel Pentium Pro (and above) CPUs - including all later Pentium-series processors except the 400 MHz bus versions of the Pentium M." All of Intel's listed Pentium CPU's support Intel64, which makes me seriously doubt they will support PAE with a 32-bit OS. And Wikipedia's claim is so vague, I have no idea if they mean up-to-and-including the x64 Prescott CPUs. PAE is supposed to be an aspect of the x86 architecture, and I believe it is no longer supported in an x64 environment. Please correct me if I am wrong.

  Read the article

< Previous Page | 729 730 731 732 733 734 735 736 737 738 739 740  | Next Page >