Search Results

Search found 2042 results on 82 pages for 'booting'.

Page 74/82 | < Previous Page | 70 71 72 73 74 75 76 77 78 79 80 81  | Next Page >

• No sound out of headphone port

  - by Thanatos

  I cannot get sound out of the headphone port. Headphones are plugged in, and sound comes out of the internal speakers. Windows behaves normally (sound switches to headphones when headphones are inserted). It did work in Linux at one point, but something changed, we're just not sure what. Rebooting doesn't fix. This appears to occur whether or not PulseAudio is running. Things I've tried: Rebooting. No effect. Booting into Windows. It works properly, so probably not a hardware issue. All of alsamixer. My only controls are this: "Master" Volume bar & mutable, unmuted. Controls volume. "PCM" Volume bar only. 100%. "S/PDIF" Mutable only, currently muted, has no effect. "S/PDIF" Default PCM", Mutable only, currently unmuted, has no effect. Killing PulseAudio. No effect. (It also won't stay dead! Something appears to be restarting it, and I can't tell what, but it is annoying as fuck.) alsactl init 0, no effect. sudo rm -f /var/lib/alsa/asound.state, no effect. General system info: Ubuntu 10.04 LTS Toshiba Satellite T135D-S1324 lspci says I have: 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller

  Read the article

• IDE compatability with SATA image

  - by Ormis

  We had an old CNC machine's hard-drive fail recently. The hard-drive is an old 1275MB IDE (Seagate) and there were defiantly bad sectors on it. I was able to image the contents of the drive onto a drive in my computer before it became completely unusable (I used DD, replacing all bad sectors w/ 0s). After running a couple chdsks, the SATA drive will boot off of the image. This is great, but there's one problem. The CNC machine old and requires IDE, I've attempted to copy the currently booting image off of the SATA drive and onto IDE drives numerous times in numerous ways and every time I do so the machines return that a boot device cannot be found. Some other information: The file system is fat32, running windows 98 The SATA drive is an 80gb drive I have tried copying the image to three 20gb and two 80gb IDE drives I have checked the jumper on the back of the IDE drives when using them If anyone has any ideas, questions, suggestions, etc. please let me know. P.S. I would just put a fresh install of win98 on the machine if i had the installation media (so that's out of the question). And if it comes to it, this is my last week working here, so I'll leave that to my co-worker. EDIT: Also, I have tried using Clonezilla as well as straight up DD to copy the image to the IDE drives.

  Read the article

• Use GRUB/GRUB2 to PXE boot OS image

  - by Jack

  Asked this in stackoverflow but they recommended I post this here: Here is the situation I am in: I currently have a Windows drive that boots XP. The BIOS does not support PXE booting so this is out of the question. Therefore, I was thinking I could install a customized GRUB bootloader on it instead such that it will have the option to PXE boot an image from a DHCP server connected to it and have the option to load Windows as it normally does (two items in menu). The catch is it may need to be automated (meaning no keyboard), so is there any way to run a script pre-boot during GRUB loading that determines if DHCP / TFTP servers are running and attempt to PXE boot an image from the network (and if not, say timeout of 10 seconds, regularly boot from Windows drive)? If this is not possible, what are some other options / suggestions? I was reading up on grub4dos as well but I'm not sure that is what I need. FWIW, I'm free to do whatever I want to the drive. I'd really appreciate some help on this as I'm not sure where to start. Thanks!

  Read the article

• USB drive was bootable, but no longer boots

  - by i-g

  I'm trying to install a new OS onto a computer from a bootable USB stick. I previously installed Ubuntu Linux and it was a piece of cake -- I downloaded the ISO image, used UNetbootin to copy it to the USB drive and make it bootable, and that was that. Now, however, no matter what I try, I can't make the same USB drive bootable again! I've tried formatting it as FAT32 and NTFS. I've tried several different Linux distributions and Windows 7. I've tried using UNetbootin, Windows 7 USB Download Tool, WinToFlash, and manually making it bootable with diskpart/bootsect/bootrec. (Yes, I've tried bootsect /nt60 x: /force.) None of this seems to be working! When I try to boot from the drive, the machine reads from it (I can see the drive's LED blinking) and then gives me the same "Insert system disk and press Enter" message. (I've disabled booting from the hard drive.) Am I missing something I need to do to make the USB drive bootable again? I think it lost some pixie dust when I formatted it with the standard Windows formatting tool (it was quicker than deleting files), but I have no idea what it was or how to get it back. The USB drive in question is a SanDisk Cruzer 8GB SDCZ6. The computer I'm working on is running Windows Vista SP1.

  Read the article

• Windows 7 breaks even in safe mode

  - by delenda

  Hi, I have a Dell XPS M1730 with Windows 7 installed. I noticed last night that after a few hours of use, the fans kicked into full and I couldn't do anything without it taking forever. Minimising windows, opening device manager or even opening process explorer took minutes and a game install I had just started took nearly 4 hours to complete. When procexp finally loaded, the refresh was so slow that it was mostly useless. From what I could gather, it was reporting 60% idle processes with procexp using nearly 40%. There were no hardware interrupts listed. When I rebooted, the problem went away for about 10 minutes and then the same thing happened. The issue persists in safe mode and even after I removed the graphics drivers, which have been an issue in the past, it still happens. Icons flash quite quickly on the desktop periodically and screen refresh is painfully slow. When booting now, the fans kick in to full as soon as the windows logon box comes up and it's taking 10 minutes to bring the desktop up. Chkdsk reports nothing and the raid check says that everything is fine. I'm thinking hardware failure, probably HDD but wanted some other opinions. I'm planning to try a linux live cd to see if it works without using the hard disks. If anyone has any input, it would be greatly appreciated. Delenda

  Read the article

• Clone a Windows Installation to a 3TB Hard Drive; MBR to GPT

  - by DanBlakemore

  I have Windows 7 Professional 64-bit installed on my desktop. Unfortunately for me and my wallet my hard drive is failing. I have purchased a 3TB hard drive as a replacement for my current 2TB drive. I would like to avoid as much hassle as possible in moving to this new drive so I would like to copy my current partition to the new drive using Gparted. The problem is that I suspect that my current partition is MBR, and I need GPT on my new drive since it is 3TB. Can I simply copy the MBR partition onto the new disk and then convert it to GPT after the fact (can you even convert the type of a partition)? Or would I need to somehow copy the contents of the partition into a GPT partition on the new drive? How do I go about making this transistion? Also, are there any issues I should be wary of booting to a GPT partition? If it matters, my motherboard is 1 year old as of May, 2012. Edit: My motherboard is 1 day old. My old one does not have UEFI compatibility, so I decided to make an upgrade to Intel today given that I would need a UEFI motherboard to use my new HDD. How much can I use a dying hard drive (bad sectors according to Hitachi Drive Fitness Test)? I have assumed not at all, to be safe.

  Read the article

• MacBook Pro (2007 - ATI-Card) Screen goes half black then shuts down the entire computer

  - by BluePerry

  Hey, when I'm starting my MBP I get about 10-60 seconds of the booting process before the screen goes half black (Its like applying a black to transparent gradient from the left side of the screen to the middle of the screen). After a 5 seconds the entire screen blacks out and the MBP shuts down. There have been issues with heat and some minor artifacts on the screen in the past but nothing serious as far as I know. Everything could be resolved by rebooting or letting the MBP cool down a bit. I would like to identify the problem now. There are 3 possibilities I can think of right now: My graphics card is defect and shuts down after a few seconds. (But if thats true, I find it kind of hard to explain the HALF black screen) My LCD-Panel is defect and sends back wrong signals so the system shuts down??? (I not sure about that) My fan or/and thermal sensors are defect and forcing the graphics card to shut down. Can anyone point if I'm right or if there yet another reason for this. I'd be thankful for any hint or tips. Cheers, Per

  Read the article

• How does one skip “Windows did not shut down successfully” in Win7-64?

  - by XenonofArcticus

  Migrating an app from an expensive and unreliable dedicated embedded x86 box running WinXP-embedded to COTS hardware (Dell E6410 laptop) running normal Win7-64. At this time, it's not feasible to deploy using Windows 7 embedded. The problem is, that the system is still sort of "embedded". The power could shut off at virtually any time without prior warning. We've stripped the OS down and removed the battery capability so that it will power down as desired. The app never writes to the disk, so it's not like we're going to corrupt anything terribly. The system is essentially idle after our app is up and running (with the exception of some computation, graphics, and TCP/IP and serial communications) so the OS enters a pretty stable state rather quickly. After a power-loss however, it rightly complains that Windows did not shut down successfully and presents the user with the Windows Error Recovery text screen. If left alone, it does eventually move on booting just fine, but we'd like to skip that step if possible. WinXP-embedded is designed to do this automatically, so I know it's possible. I've looked at the Kernel Switches but I didn't see anything documented for "Skip Windows Error Recovery". I've also read extensively on the startup process: http://homepage.ntlworld.com./jonathan.deboynepollard/FGA/windows-nt-6-boot-process.html I know I can disable the auto chkdsk in the registry, but that's not the same thing either. So, how do I streamline the boot process to not hassle the user about a situation that will be the regular normal situation?

  Read the article

• Unrelated Files Corrupted on System Restore

  - by Yar

  I restored OSX 10.6.2 today (was 10.6.3 and not booting) by copying the system over from a backup. The data directories were not touched. In the data directories, I'm seeing some files as 0 bytes, and getting permission-denied errors when copying, even when using sudo cp or the Finder itself. Some programs, differently, take the files at face value and see no permission problems (such as zip), but they see the files as zero bytes, which would be game-over for recovery. cp: .git/objects/fe/86b676974a44aa7f128a55bf27670f4a1073ca: could not copy extended attributes to /eraseme/blah/.git/objects/fe/86b676974a44aa7f128a55bf27670f4a1073ca: Operation not permitted I have tried sudo chown, sudo chmod -R 777 and sudo chflags -R nouchg which do not change the end result. Strangely, this is only affecting my .git directories (perhaps because they start with a period, but renaming them -- which works -- does not change anything). What else can I do to take ownership of these files? Edit: This question comes from StackOverflow because I originally thought it was a GIT problem. It's definitely not (just) GIT. Anyway, this is to help put some of the comments in context.

  Read the article

• quad sli with gtx 690 not working

  - by Moaadh

  I have two cards GTX 690 (dual core). I did the Sli successfully. Nvidia control panel acknowledges the two cards as quad Sli. However, the problem is that Windows 7 64-bit Ultimate is showing me the graph memory size as 4 GB while it is supposed to be 8 GB because of the Sli. Also the benchmark from all software is giving me a very low score compared to some other guy's benchmark on YouTube. It gives me a big headache. Does anyone know why this is happening? If so, how can I get Windows 7 to recognize all 8 GB of memory? Thanks for your help in advance. My computer specifications: (Processor: Intel Core i7-3930k @3.2GHz(12CPUs))--- (Memory: 65536 MB Ram 1866 MHz)-- (OS: Windows 7 Ultimate 64-bit)-- (OCZ 240GB as SSD PCIe drive for booting and storage disk)-- (DirextX version: DirectX 11)-- (VGA Card: 2 X EVGA GTX 690 Dual GPU. Each GPU is 2 GB, so total memory should be 8 GB.)-- (MotherBoard: ASUS Rampage IV Extreme)-- Others with lesser specifications get a 2500 score in heaven benchmark while I get 1501 as if it is one card.

  Read the article

• How to Dual-Boot Kali-Linux and Windows 8.1?

  - by Ceyhun

  I have Acer V3-772G 1 TB Harddisk. I shrinked my biggest partition in order to install Kali Linux. When installing Kali, GRUB couldn't detect windows 8 so I kept going on(I installed grub as my masterboot). After installed Kali there was no way to boot Windows 8.1, but booting Kali was OK with GRUB in legacy-BIOS. When I tried to change bios to UEFI it couldn't find any OS (took too much time, nearly 1 hour). So I tried to update GRUB with boot-repair within a Ubuntu Live USB. But after updating GRUB I terrified, in UEFI and Legacy mode grub couldn't find ANY OS (Both Kali and Windows) so I have no option other than using Ubuntu Live. I tried every possible options but nothing has worked for me. I tried rEFInd in UEFI mode it worked only for Kali. I still cannot boot my windows 8.1 . I considered to restore to factory setting with a Windows Rescue USB but kept telling me "No driver found". Please help me to dual boot or remove Kali and restore my Windows 8.1

  Read the article

• What does it mean to install two OS's alongside each other?

  - by Josh

  I currently have Windows 7 installed on my PC. However, I just tried out Ubuntu via booting from a disc and I love it. I want to install it onto my HDD, but I don't want to get rid of Windows 7. I know HOW to do this, but I am a little unsure what the consequences might be. What does it mean to install Ubuntu alongside Windows? Do they share the same resources? Also, I have my HDD already partitioned into two sections, a 70 GB section where Windows is installed and then another 400 GB section where all my data is stored. There is currently 26 GB free on the 70GB partition. I know Ubuntu doesn't take up much space. However, if I install Ubuntu in that space, will I still be able to install programs on Windows in the future? My main concern is that I am going to short-change my hard drive space for future installations. EDIT: I guess another big question I have is if I install a program on one OS, will the other be able to use it?

  Read the article

• USB drive was bootable, but no longer isn't

  - by i-g

  I'm trying to install a new OS onto a computer from a bootable USB stick. I previously installed Ubuntu Linux and it was a piece of cake -- I downloaded the ISO image, used UNetbootin to copy it to the USB drive and make it bootable, and that was that. Now, however, no matter what I try, I can't make the same USB drive bootable again! I've tried formatting it as FAT32 and NTFS. I've tried several different Linux distributions and Windows 7. I've tried using UNetbootin, Windows 7 USB Download Tool, WinToFlash, and manually making it bootable with diskpart/bootsect/bootrec. (Yes, I've tried bootsect /nt60 x: /force.) None of this seems to be working! When I try to boot from the drive, the machine reads from it (I can see the drive's LED blinking) and then gives me the same "Insert system disk and press Enter" message. (I've disabled booting from the hard drive.) Am I missing something I need to do to make the USB drive bootable again? The USB drive in question is a SanDisk Cruzer 8GB SDCZ6. The computer I'm working on is running Windows Vista SP1.

  Read the article

• INACCESSIBLE_BOOT_DEVICE after installing Linux on same drive

  - by kdgregory

  History: My PC was configured with two drives: an 80G on IDE 0 Primary that was running Win2K, and a 320G on IDE 0 Secondary that was running Linux (Ubuntu). I decided to pull the 80Gb drive out of the system, so dd'd the entire 80 G drive (/dev/sda) onto the 320 (/dev/sdb) -- this included the MBR and partition table. Then I pulled the drive, plugged the 320 into IDE 0 Primary, and rebooted. The Windows partition worked at this point. Then I installed Ubuntu into the remaining space on the 320. It works. However, when I try to boot into Windows, I get a BSOD with the following message: *** STOP: 0x0000007B (0x89055030,0xC000014F,0x00000000,0x00000000) INACCESSILE_BOOT_DEVICE Before the BSOD I see the Win2K splash screen, and it claims to be "starting windows" for a couple of seconds -- so it appears that the first stage boot loader is working as expected. Ditto when I try booting in Safe Mode. After reading the Microsoft KB article, I booted into the recovery console and tried running chkdsk /r. It refused to run, claiming that the drive was corrupted (sorry, didn't write down the exact error message). However, I can mount the drive from Linux, and access all files. And for what it's worth, I can scan the drive using the Linux "Disk Utility" (this is Ubuntu, the menus don't show real program names), it claims the drive to be clean. The KB article mentioned that boot.ini could be the problem, so here it is: timeout=10 default=multi(0)disk(0)rdisk(0)partition(1)\WINDOWS [operating systems] multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows 2000 Professional" /fastdetect Any pointers on what to do next?

  Read the article

• Azure VM won't boot after sysprep; integration tools installed

  - by Mark Williams

  I have installed the Azure Integration Components and used sysprep on a Windows 2012 VM. Now the machine won't start up. I uploaded the VHD to Azure - it failed there too. When I start up the VM I get a PowerShell window that hangs out for a bit; eventually I get the following error, after which the machine restarts. New-Object: The dependency service or group failed to start. (Exception from HRESULT: 0x8007042C) At line1: char:1 New-Object -comobject WaAgent.WindowsSetupComponent | % { $_.HandleSetupError() ... ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +CategoryInfo : ResourceUnavailable (:) [New-Object], COMException +FullyQualifiedErrorId: NoCOMClassIdentified,Microsoft.PowerShell.Commands.NewObjectCommand I have tried renaming unattended.xml and turning on bootlogging. Neither of those yielded much help. Is there a way I can disable the Azure components that run during OOBE? That seems to be the source of the problem. Mounting the VHD is easy. 0x8007042C looks like a firewall issue, based on my googling. Unfortunately I can't get the machine to boot so I can figure that issue out. Also, I can't get around this problem by booting into safe mode. Thanks for your help, guys.

  Read the article

• Replaced CPU and black screen but no beep?

  - by luke

  I'm having a bit of trouble with a GIGABYTE GA-MA78G-DS3H (rev. 2.0) motherboard. Recently when trying to clean my AMD Phenom II X 4 CPU, I dropped it and broke some pins. I have now brought a Athlon 64 X2 5400+. However, it does not seem to work. To begin with, I cleared the CMOS via the jumper located near the battery. This was because I had my AMD Phenom II overclocked and did not wish for the same voltage to go to the new CPU. I then tried booting with the monitor plugged into the chipsets VGA but no luck. No signal was sent to the monitor, and the monitor just went into standby. I then tried it off the graphics card but the same happened again. Then I tried to check whether the CPU could executed some BIOS codes by stripping the RAM out and making sure a speaker was plugged in but no beeps could be heard. I replaced the speaker and tried again but no luck. The CPU is brand-new so what is going wrong?

  Read the article

• Boot stuck at blinking cursor before GRUB - only works via BIOS boot menu

  - by delta1

  I have a new box running Debian Squeeze. Grub is installed on /dev/sda, but when booting up I just get a blinking cursor, before the Grub menu. I can only boot to grub successfully when I choose boot options (during post) and select that specific drive! I have made sure the correct drive is set to boot first in the BIOS. So Grub works, but the system won't boot to that drive automatically? Any ideas on what could cause this? Drives sda/b/c are all 2TB (sda runs the system with b/c as raid device md0) with the following partitions: $ cat /proc/partitions major minor #blocks name 8 0 1953514584 sda 8 1 977 sda1 8 2 9765625 sda2 8 3 6445313 sda3 8 4 1937302627 sda4 8 32 1953514584 sdc 8 16 1953514584 sdb 9 0 1953513424 md0 but # fdisk -l /dev/sda gives WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sda1 1 243202 1953514583+ ee GPT Any insight into this strange behaviour would be greatly appreciated.

  Read the article

• Repairing Windows 7 boot after Ubuntu 10.10 install

  - by Ted

  I've read various threads on this after googling, including one on this site. I had Windows 7 installed on an SSD. I wanted to try Ubuntu so I created a partition for it on the SSD and booted with the live CD to install Ubuntu. Went through the install and somehow Ubuntu carved out another partition on the SSD rather than using the one I had already created. Windows 7 would then not boot but Ubuntu would. I booted with my 7 cd and ran the automatic startup repair, it didn't find any problems. I then ran the bootsect command on the drive with 7. It said it repaired the bootmgr but Windows still would not boot and now Ubuntu won't either. I read somewhere else that it may be due to the partition that 7 was on being changed during the install. I don't care about the Ubuntu installation but I don't want to lose the 7 install, can I delete the ubuntu partition through booting with the 7 cd? Will that do any good? Thank you all! I'm stumped even though I've done startup repairs before, just not after Ubuntu install.

  Read the article

• PXELinux and compressed kernels/images

  - by Yvan JANSSENS

  Is it possible to boot compressed kernels with a compressed initrd with PXELinux? First, a little background: We created a custom Linux distro, for diskless OpenCL computing nodes. We want those nodes to fetch their OS from the network. Our Distro is composed out of a kernel (duh) and a large initrd which is loaded into RAM and everything is executed from there. We chose to run everything off the initrd for two reasons: NFS was not an option to serve the filesystem's extra contents Fast file access from RAM. No persistent storage needed, data and config is pulled dynamically through a SOAP service. Now our initrd is about 450M in size. At our network speeds, it takes about two to three minutes to load a single client. Will compression speed up te downloading, and if yes, which one should be used? Is LZMA supported by PXELinux, or do we need to stick to bzip2 or gzip? Because of the 2-3 minutes loading time, booting 15 nodes over the same network link takes quite a lot of time. We decided not to use hard drives or CD/DVD drives, for financial reasons (cheapest HDD @ €30 times 15 is a lot of money saved ;-) ) So, our question is: what compression options are available for this setup? And how do we do this? Thank you for your time! Yvan Janssens

  Read the article

• Computer wont start, just blinks on and off

  - by Ryan

  This is really strange. I had a comp that was working fine for over a year, then suddenly it started to shut off, it got so bad that I press the power button and in around 30 secs while booting windows it would shut off, then 20 secs... then 10 secs, then it refused to start all together. So I bought a new PSU (850w Thermaltake, the old one was 550w corsair) thinking that was the problem, I fitted the new PSU now and its the same thing, I press the power button and my fans start for a split second (they have led lights on them, so the lights come on) and then everything goes off again. I thought maybe it was my power button that was loose on my comp, luckily I had another chassis near by so I disconnected the powerSW from the old one and put ran the powerSW from the new chassis, press the power on the new chassis and same thing, it blinks for a split second and off again. Double checked connections from the PSU to the cpu power as well as board mobo power, its tight. It's pretty unlikely both the PSUs have the same exact problem so am lost... Suggestions?

  Read the article

• Assembling Software RAID in Live CD for data recovery

  - by Maletor

  I need help recovering some data that's on my RAID which is on a LVM on my server running Ubuntu. What happened was I deleted the logical volume that controlled my swap space which was on a partition on drives sda2, sdb2, sdc2, and sdd2 in RAID1. This foobared my whole system for one reason or another. Booting leave me with grub rescue and an error saying that it is an unknown filesystem. When I boot to a live cd I can see my RAID arrays and I can even start them up. However, it doesn't appear to mount them anywhere so I can't see the data. I am in the live cd now and I have done sudo apt-get install mdadm lvm2 so it should be mounting them correctly. I just can't see why it wouldn't. Please any help is appreciated here. Here is some output. By the way, there are 3 RAIDs, 1) /boot 100mb RAID1, 2) swap 10gb RAID1, 3) root 990GB RAID5 ubuntu@ubuntu:~$ df -h Filesystem Size Used Avail Use% Mounted on aufs 124M 101M 18M 86% / none 2.0G 324K 2.0G 1% /dev /dev/sde1 2.0G 826M 1.2G 42% /cdrom /dev/loop0 667M 667M 0 100% /rofs none 2.0G 164K 2.0G 1% /dev/shm tmpfs 2.0G 28K 2.0G 1% /tmp none 2.0G 92K 2.0G 1% /var/run none 2.0G 0 2.0G 0% /var/lock none 2.0G 0 2.0G 0% /lib/init/rw /dev/md1 91M 73M 15M 84% /media/5ac3dbf1-a6c5-409c-96ae-edc6e27992c7 ubuntu@ubuntu:~$ cat /etc/fstab aufs / aufs rw 0 0 tmpfs /tmp tmpfs nosuid,nodev 0 0 /dev/sda2 swap swap defaults 0 0 /dev/sdb2 swap swap defaults 0 0 /dev/sdc2 swap swap defaults 0 0 /dev/sdd2 swap swap defaults 0 0

  Read the article

• Fedora 19 no longer bootable

  - by Parisa

  I had fedora dual-booted with windows on my laptop for a while but with windows refresh grub was gone and my system directly booted windows. I booted fedora with my systems boot options and with this tutorial: https://fedoraproject.org/wiki/GRUB_2 I reinstalled grub2 but then had my system booted into an empty grub prompt: grub So I found the drive containing vmlinuz and initramfs (completely sure about thair location and versions) and tried to manually boot it but after the boot command it said: no suitable video mode found booting in blind mode and nothing happened. Such a tragedy... I have already tried to use live disks rescue system. Funny but troubleshooting options don't apear on my laptop while they do on my desktop pc. I cant even go to boot prompt on my lenovo idepad z400 laptop. I also tried EasyBCD so maybe I could boot it with windows but it comes up with this error: missing AutoNeoGrub().mbr Now I have removed the grub prompt (don't know why) and its really hard for me to reinstall my dearly customized fedora. If anyone knows a way to help boot it again or reinstall it keeping my files and installations I really need it. Thanks PS:I have already tried Boot-repair Disk but it asks me to enable the repo containing grub-efi on my fedora to reinstall the grub2 and fix the boot for me (how could i?).

  Read the article

• Oracle Linux screen freezes during installation

  - by Fearless

  I was installing Oracle Linux 6.4 on a server, and the screen suddenly froze. Here were the previous steps: I put in the disk, clicked install, checked the disk (no errors), did pre-install setup (clock, root password, host+domain name, etc.), configured two 40GB hard drives in a RAID1 array (no swap, 3100mb encrypted raid partitions, ~100mb ext4 partition mounting to /boot, encrypted ext4 RAID device with mounting to /), selected packages, hit continue. The system did its short preinstall processes, then when to the main installation screen with the long status bar. The installer proceeded like always, but around package 250 out of ~1000, the screen suddenly went black with a text cursor in the upper left corner of the screen and the mouse cursor in its previous place. Neither cursor moved and the only thing that triggered a response was a ctrl-alt-delete that rebooted it. I have run this in VMs before without this issue. Memtest hasn't reported anything, and the media check went smoothly. The machine has supported Ubuntu server without issues before. Any ideas? I have tried booting after that, but the grub bootloader tries to find fd0 for some reason (I have no idea why it would search for the floppy disk). UPDATE My server successfully installed, but won't boot up. I think that, for some reason, it is still using the old bootloader from the previous installation. Any ideas on how to fix that?

  Read the article

• Windows 8 not shutting down properly

  - by Patrick

  Since installing Windows 8, the computer hasn't been shutting down properly. When selecting to power down, the PC quickly displays the shutting down screen, the monitor powers off, and the computer remains on but unresponsive. After about 5 minutes, the computer will turn off. Upon booting into windows again, I am informed that Windows didn't properly shut down. I'm running a fast SSD, and it's a clean install of Windows 8, so there's no way Windows is taking that time to do some sort of hibernate on shutdown or whatever - not to mention the error when entering Windows the next time. This happens on every shut down. Restart works as expected. EDIT: Formatting again didn't work. Fails regardless of drivers installed. Event viewer Always these two messages in close succession: Error (event ID 6008): The previous system shutdown at 7:45:21 PM on ?27/?10/?2012 was unexpected. Critical (kernel power, event ID 41): The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly.

  Read the article

• Recovering a broken NTFS filesystem?

  - by OverTheRainbow

  A much-needed Windows Update broke a Vista laptop that was running fine until then: After booting up, Windows displays "Please wait..." but it never goes anywhere. I waited for a couple of hours, there is a bit of disk activity, but it didn't work out in the end. I booted with the Vista DVD, chose "Repair your computer" which said that there was nothing wrong :-/ Next, I booted it up with a Linux USB keydrive, and ran Gparted 0.8.1 (which includes ntfsresize v2011.4.12AR.4 libntfs-3g) which displays a bunch of warnings for the NTFS partition where the Vista system is located such as: ntfs_mst_post_read_fixup: magic: 0x00000000 size: 1024 usa_ofs: 0 usa_count: 65535: Invalid argument Record 16 has no FILE magic (0x0) Next, I ran ntfsfix /dev/sda2, which said: Mounting volume... OK Processing of $MFT and $MFTMirr completed successfully. NTFS volume version is 3.1. NTFS partition /dev/sda2 was processed successfully. Next, I rebooted Vista, which did a CHKDSK, before rebooting. But I'm still getting nowhere with "Please wait..." Before I copy the user's data to another host and reinstall Vista from a DVD, does someone know what I could try? Thank you. Edit: In case someone else has the same issue... After the BIOS, hit F8 and choose "Repair your computer", followed by "Toshiba HDD Recovery". In addition to a 1,5GB partition labelled "WinRE", the hard disk contains a second partition labeled "Data" from which the application will fetch a system image and reinstall it in the "Vista" partition. Make sure you copy your data out of the system partition before doing this.

  Read the article

< Previous Page | 70 71 72 73 74 75 76 77 78 79 80 81  | Next Page >