anonymous access - Page 754

Can't connect to samba using openVPN

- by Arthur

I'm fairly new to using VPN. For a home project I'm running a OpenVPN server. This server runs within a network 192.168.2.0 and subnet 255.255.255.0 I can connect to this net work using the ip range 5.5.0.0 I guess the subnet is 255.255.255.192, but I'm not really sure about that. When connecting to my VPN network I can access the server via 5.5.0.1 and I can see the samba shares created on that machine. However I'm not allowed to connect to the samba share. When I look at the samba log of the computer which tries to connect I can see these messages: lib/access.c:338(allow_access) Denied connection from 5.5.0.132 (5.5.0.132) These are the share definition in /etc/samba/smb.conf interfaces = 192.168.2.0/32 5.5.0.0/24 security = user # wins-support = no # wins-server = w.x.y.z. // A LOT OF MORE SETTINGS AND COMMENTS hosts allow = 127.0.0.1 192.168.2.0/24 5.5.0.132/24 hosts deny = 0.0.0.0/0 browseable = yes path = [path to share] directory mask = 0755 force create mode = 0755 valid users = [a valid user, which i use to login with] writeable = yes force group = [the group i force to write with] force user = [the user i force to write with] This is the output of the ifconfig command as0t0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:5.5.0.1 P-t-P:5.5.0.1 Mask:255.255.255.192 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:200 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) as0t1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:5.5.0.65 P-t-P:5.5.0.65 Mask:255.255.255.192 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:200 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) as0t2 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:5.5.0.129 P-t-P:5.5.0.129 Mask:255.255.255.192 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:xxxx errors:0 dropped:0 overruns:0 frame:0 TX packets:xxxx errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:200 RX bytes:xxxx (xxxx MB) TX bytes:12403514 (xxxx MB) as0t3 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:5.5.0.193 P-t-P:5.5.0.193 Mask:255.255.255.192 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:7041 errors:0 dropped:0 overruns:0 frame:0 TX packets:9797 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:200 RX bytes:xxxx (xxxx KB) TX bytes:xxxx (xxxx MB) eth1 Link encap:Ethernet HWaddr 00:0e:2e:61:78:21 inet addr:192.168.2.100 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: xxxx:xxxx:xxxx:xxxx:7821/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:xxxx errors:0 dropped:0 overruns:0 frame:0 TX packets:xxxx errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:xxxx (xxxx MB) TX bytes:xxxx (xxxx MB) Interrupt:16 Base address:0x6000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:xxxx errors:0 dropped:0 overruns:0 frame:0 TX packets:xxxx errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:xxxx (xxxx MB) TX bytes:xxxx (xxxx MB) Can anyone tell me what is going wrong? My server is running Ubuntu 12.04 LTS

Read the article

/usr/bin/sshd isn't linked against PAM on one of my systems. What is wrong and how can I fix it?

- by marc.riera

Hi, I'm using AD as my user account server with ldap. Most of the servers run with UsePam yes except this one, it has lack of pam support on sshd. root@linserv9:~# ldd /usr/sbin/sshd linux-vdso.so.1 => (0x00007fff621fe000) libutil.so.1 => /lib/libutil.so.1 (0x00007fd759d0b000) libz.so.1 => /usr/lib/libz.so.1 (0x00007fd759af4000) libnsl.so.1 => /lib/libnsl.so.1 (0x00007fd7598db000) libcrypto.so.0.9.8 => /usr/lib/libcrypto.so.0.9.8 (0x00007fd75955b000) libcrypt.so.1 => /lib/libcrypt.so.1 (0x00007fd759323000) libc.so.6 => /lib/libc.so.6 (0x00007fd758fc1000) libdl.so.2 => /lib/libdl.so.2 (0x00007fd758dbd000) /lib64/ld-linux-x86-64.so.2 (0x00007fd759f0e000) I have this packages installed root@linserv9:~# dpkg -l|grep -E 'pam|ssh' ii denyhosts 2.6-2.1 an utility to help sys admins thwart ssh hac ii libpam-modules 0.99.7.1-5ubuntu6.1 Pluggable Authentication Modules for PAM ii libpam-runtime 0.99.7.1-5ubuntu6.1 Runtime support for the PAM library ii libpam-ssh 1.91.0-9.2 enable SSO behavior for ssh and pam ii libpam0g 0.99.7.1-5ubuntu6.1 Pluggable Authentication Modules library ii libpam0g-dev 0.99.7.1-5ubuntu6.1 Development files for PAM ii openssh-blacklist 0.1-1ubuntu0.8.04.1 list of blacklisted OpenSSH RSA and DSA keys ii openssh-client 1:4.7p1-8ubuntu1.2 secure shell client, an rlogin/rsh/rcp repla ii openssh-server 1:4.7p1-8ubuntu1.2 secure shell server, an rshd replacement ii quest-openssh 5.2p1_q13-1 Secure shell root@linserv9:~# What I'm doing wrong? thanks. Edit: root@linserv9:~# cat /etc/pam.d/sshd # PAM configuration for the Secure Shell service # Read environment variables from /etc/environment and # /etc/security/pam_env.conf. auth required pam_env.so # [1] # In Debian 4.0 (etch), locale-related environment variables were moved to # /etc/default/locale, so read that as well. auth required pam_env.so envfile=/etc/default/locale # Standard Un*x authentication. @include common-auth # Disallow non-root logins when /etc/nologin exists. account required pam_nologin.so # Uncomment and edit /etc/security/access.conf if you need to set complex # access limits that are hard to express in sshd_config. # account required pam_access.so # Standard Un*x authorization. @include common-account # Standard Un*x session setup and teardown. @include common-session # Print the message of the day upon successful login. session optional pam_motd.so # [1] # Print the status of the user's mailbox upon successful login. session optional pam_mail.so standard noenv # [1] # Set up user limits from /etc/security/limits.conf. session required pam_limits.so # Set up SELinux capabilities (need modified pam) # session required pam_selinux.so multiple # Standard Un*x password updating. @include common-password Edit2: UsePAM yes fails With this configuration ssh fails to start : root@linserv9:/home/admmarc# cat /etc/ssh/sshd_config |grep -vE "^[ \t]*$|^#" Port 22 Protocol 2 ListenAddress 0.0.0.0 RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile .ssh/authorized_keys ChallengeResponseAuthentication yes UsePAM yes Subsystem sftp /usr/lib/sftp-server root@linserv9:/home/admmarc# The error it gives is as follows root@linserv9:/home/admmarc# /etc/init.d/ssh start * Starting OpenBSD Secure Shell server sshd /etc/ssh/sshd_config: line 75: Bad configuration option: UsePAM /etc/ssh/sshd_config: terminating, 1 bad configuration options ...fail! root@linserv9:/home/admmarc#

Read the article

Duplicate GET request from multiple IPs - can anyone explain this?

- by dwq

We've seen a pattern in our webserver access logs which we're having problem explaining. A GET request appears in the access log which is a legitimate, but private, url as part of normal e-commerce website use (by private, we mean there is a unique key in a url form variable generated specifically for that customer session). Then a few seconds later we get hit with an identical request maybe 10-15 times within the space of a second. The duplicate requests are all from different IP addresses. The UserAgent for the duplicates are all the same (but different from the original request). The reverse DNS lookup on the IPs for all the duplicates requests resolve to the same large hosting company. Can anyone think of a scenario what would explain this? EDIT 1 Here's an example that's probably anonymised beyond being any actual use, but it might give an idea of the sort of pattern we're seeing (it's from a search query as they sometimes get duplicated too): xx.xx.xx.xx - - [21/Jun/2013:21:42:57 +0100] "GET /search.html?search=widget&Submit=Search HTTP/1.0" 200 5475 "http://www.ourdomain.com/index.html" "Mozilla/5.0 (compatible; MSIE 10.0; Windows NT 6.1; WOW64; Trident/6.0)" xx.xx.xx.xx - - [21/Jun/2013:21:43:03 +0100] "GET /search.html?search=widget&Submit=Search HTTP/1.0" 200 5475 "" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_6_7) AppleWebKit/534.30 (KHTML, like Gecko) Chrome/12.0.742.91 Safari/534.30" xx.xx.xx.xx - - [21/Jun/2013:21:43:03 +0100] "GET /search.html?search=widget&Submit=Search HTTP/1.0" 200 5475 "" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_6_7) AppleWebKit/534.30 (KHTML, like Gecko) Chrome/12.0.742.91 Safari/534.30" xx.xx.xx.xx - - [21/Jun/2013:21:43:04 +0100] "GET /search.html?search=widget&Submit=Search HTTP/1.0" 200 5475 "" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_6_7) AppleWebKit/534.30 (KHTML, like Gecko) Chrome/12.0.742.91 Safari/534.30" xx.xx.xx.xx - - [21/Jun/2013:21:43:04 +0100] "GET /search.html?search=widget&Submit=Search HTTP/1.0" 200 5475 "" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_6_7) AppleWebKit/534.30 (KHTML, like Gecko) Chrome/12.0.742.91 Safari/534.30" xx.xx.xx.xx - - [21/Jun/2013:21:43:04 +0100] "GET /search.html?search=widget&Submit=Search HTTP/1.0" 200 5475 "" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_6_7) AppleWebKit/534.30 (KHTML, like Gecko) Chrome/12.0.742.91 Safari/534.30" xx.xx.xx.xx - - [21/Jun/2013:21:43:04 +0100] "GET /search.html?search=widget&Submit=Search HTTP/1.0" 200 5475 "" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_6_7) AppleWebKit/534.30 (KHTML, like Gecko) Chrome/12.0.742.91 Safari/534.30" xx.xx.xx.xx - - [21/Jun/2013:21:43:04 +0100] "GET /search.html?search=widget&Submit=Search HTTP/1.0" 200 5475 "" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_6_7) AppleWebKit/534.30 (KHTML, like Gecko) Chrome/12.0.742.91 Safari/534.30" xx.xx.xx.xx - - [21/Jun/2013:21:43:04 +0100] "GET /search.html?search=widget&Submit=Search HTTP/1.0" 200 5475 "" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_6_7) AppleWebKit/534.30 (KHTML, like Gecko) Chrome/12.0.742.91 Safari/534.30" xx.xx.xx.xx - - [21/Jun/2013:21:43:04 +0100] "GET /search.html?search=widget&Submit=Search HTTP/1.0" 200 5475 "" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_6_7) AppleWebKit/534.30 (KHTML, like Gecko) Chrome/12.0.742.91 Safari/534.30" xx.xx.xx.xx - - [21/Jun/2013:21:43:04 +0100] "GET /search.html?search=widget&Submit=Search HTTP/1.0" 200 5475 "" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_6_7) AppleWebKit/534.30 (KHTML, like Gecko) Chrome/12.0.742.91 Safari/534.30" UPDATE 2 Sometimes it is part of a checkout flow that's duplicated to I'd think twitter is unlikely.

Read the article

DNS with name.com and Amazon S3

- by aledalgrande

I have a website on a bucket in Amazon S3, and recently started to get emails from Google "Googlebot can't access your site". When I go to Webmaster Tools and I try to fetch in fact it doesn't work. Also people in locations different from mine sometimes reported they could not access the website. Now for curiosity I tried from my terminal: $ host xxx xxx is an alias for xxx.s3-website-us-west-1.amazonaws.com. xxx.s3-website-us-west-1.amazonaws.com is an alias for s3-website-us-west-1.amazonaws.com. s3-website-us-west-1.amazonaws.com has address yyy.yyy.yyy.yyy And when I try with dig: $ dig xxx ; <<>> DiG 9.8.3-P1 <<>> xxx ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 17860 ;; flags: qr rd ra; QUERY: 1, ANSWER: 3, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;xxx. IN A ;; ANSWER SECTION: xxx. 300 IN CNAME xxx.s3-website-us-west-1.amazonaws.com. xxx.s3-website-us-west-1.amazonaws.com. 60 IN CNAME s3-website-us-west-1.amazonaws.com. s3-website-us-west-1.amazonaws.com. 60 IN A yyy ;; Query time: 1514 msec ;; SERVER: 75.75.75.75#53(75.75.75.75) ;; WHEN: Fri Aug 22 12:32:13 2014 ;; MSG SIZE rcvd: 127 It seems OK to me. Why would Google tell me there is a DNS error? UPDATE: Google also cannot fetch robots.txt, but I can fetch it from my browser. UPDATE 2: I have a forwarding on the root to the www.* hostname: $ dig thenifty.me ; <<>> DiG 9.8.3-P1 <<>> thenifty.me ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 49286 ;; flags: qr rd ra; QUERY: 1, ANSWER: 0, AUTHORITY: 1, ADDITIONAL: 0 ;; QUESTION SECTION: ;thenifty.me. IN A ;; AUTHORITY SECTION: thenifty.me. 300 IN SOA ns1hwy.name.com. support.name.com. 1 10800 3600 604800 300 ;; Query time: 148 msec ;; SERVER: 75.75.75.75#53(75.75.75.75) ;; WHEN: Fri Aug 22 13:32:56 2014 ;; MSG SIZE rcvd: 88

Read the article

Squid not caching files (Randomly)

- by Heinrich

I want to use an intercepting squid server to cache specific large zip files that users in my network download frequently. I have configured squid on a gateway machine and caching is working for "static" zip files that are served from an Apache web server outside our network. The files that I want to have cached by squid are zip files 100MB which are served from a heroku-hosted Rails application. I set an ETag header (SHA hash of the zip file on the server) and Cache-Control: public header. However, these files are not cached by squid. This, for example, is a request that is not cached: $ curl --no-keepalive -v -o test.zip --header "X-Access-Key: 20767ed397afdea90601fda4513ceb042fe6ab4e51578da63d3bc9b024ed538a" --header "X-Customer: 5" "http://MY_APP.herokuapp.com/api/device/v1/media/download?version=latest" * Adding handle: conn: 0x7ffd4a804400 * Adding handle: send: 0 * Adding handle: recv: 0 ... > GET /api/device/v1/media/download?version=latest HTTP/1.1 > User-Agent: curl/7.30.0 > Host: MY_APP.herokuapp.com > Accept: */* > X-Access-Key: 20767ed397afdea90601fda4513ceb042fe6ab4e51578da63d3bc9b024ed538a > X-Customer: 5 > 0 0 0 0 0 0 0 0 --:--:-- 0:00:09 --:--:-- 0< HTTP/1.1 200 OK * Server Cowboy is not blacklisted < Server: Cowboy < Date: Mon, 18 Aug 2014 14:13:27 GMT < Status: 200 OK < X-Frame-Options: SAMEORIGIN < X-Xss-Protection: 1; mode=block < X-Content-Type-Options: nosniff < ETag: "95e888938c0d539b8dd74139beace67f" < Content-Disposition: attachment; filename="e7cce850ae728b81fe3f315d21a560af.zip" < Content-Transfer-Encoding: binary < Content-Length: 125727431 < Content-Type: application/zip < Cache-Control: public < X-Request-Id: 7ce6edb0-013a-4003-a331-94d2b8fae8ad < X-Runtime: 1.244251 < X-Cache: MISS from AAA.fritz.box < Via: 1.1 vegur, 1.1 AAA.fritz.box (squid/3.3.11) < Connection: keep-alive In the logs squid is reporting a TCP_MISS. This is the relevant excerpt from my squid file: # Squid normally listens to port 3128 http_port 3128 http_port 3129 intercept # Uncomment and adjust the following to add a disk cache directory. maximum_object_size 1000 MB maximum_object_size_in_memory 1000 MB cache_dir ufs /usr/local/var/cache/squid 10000 16 256 cache_mem 2000 MB # Leave coredumps in the first cache dir coredump_dir /usr/local/var/cache/squid cache_store_log daemon:/usr/local/var/logs/cache_store.log #refresh_pattern -i (/cgi-bin/|\?) 0 0% 0 refresh_pattern -i .(zip) 525600 100% 525600 override-expire ignore-no-cache ignore-no-store refresh_pattern . 0 20% 4320 ## DNS Configuration dns_nameservers 8.8.8.8 8.8.4.4 After trying around for some time I realized that squid is sometimes deciding that my file is cacheable, sometimes not, depending on whether and when I enable/disable the dns_nameservers directive. What could be wrong here?

Read the article

iptables rule(s) to send openvpn traffic from clients over an sshuttle tunnel?

- by Sam Martin

I have an Ubuntu 12.04 box with OpenVPN. The VPN is working as expected -- clients can connect, browse the Web, etc. The OpenVPN server IP is 10.8.0.1 on tun0. On that same box, I can use sshuttle to tunnel into another network to access a Web server on 10.10.0.9. sshuttle does its magic using the following iptables commands: iptables -t nat -N sshuttle-12300 iptables -t nat -F sshuttle-12300 iptables -t nat -I OUTPUT 1 -j sshuttle-12300 iptables -t nat -I PREROUTING 1 -j sshuttle-12300 iptables -t nat -A sshuttle-12300 -j REDIRECT --dest 10.10.0.0/24 -p tcp --to-ports 12300 -m ttl ! --ttl 42 iptables -t nat -A sshuttle-12300 -j RETURN --dest 127.0.0.0/8 -p tcp Is it possible to forward traffic from OpenVPN clients over the sshuttle tunnel to the remote Web server? I'd ultimately like to be able to set up any complicated tunneling on the server, and have relatively "dumb" clients (iPad, etc.) be able to access the remote servers via OpenVPN. Below is a basic diagram of the scenario: [Edit: added output from the OpenVPN box] $ sudo iptables -nL -v -t nat Chain PREROUTING (policy ACCEPT 1498 packets, 252K bytes) pkts bytes target prot opt in out source destination 1512 253K sshuttle-12300 all -- * * 0.0.0.0/0 0.0.0.0/0 Chain INPUT (policy ACCEPT 322 packets, 58984 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 584 packets, 43241 bytes) pkts bytes target prot opt in out source destination 587 43421 sshuttle-12300 all -- * * 0.0.0.0/0 0.0.0.0/0 Chain POSTROUTING (policy ACCEPT 589 packets, 43595 bytes) pkts bytes target prot opt in out source destination 1175 76298 MASQUERADE all -- * eth0 10.8.0.0/24 0.0.0.0/0 Chain sshuttle-12300 (2 references) pkts bytes target prot opt in out source destination 17 1076 REDIRECT tcp -- * * 0.0.0.0/0 10.10.0.0/24 TTL match TTL != 42 redir ports 12300 0 0 RETURN tcp -- * * 0.0.0.0/0 127.0.0.0/8 $ sudo iptables -nL -v -t filter Chain INPUT (policy ACCEPT 97493 packets, 30M bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 131K 109M ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 1370 89160 ACCEPT all -- * * 10.8.0.0/24 0.0.0.0/0 0 0 REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable [Edit 2: more OpenVPN server output] $ netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 [Edit 3: still more debug output] IP forwarding appears to be enabled correctly on the OpenVPN server: # find /proc/sys/net/ipv4/conf/ -name forwarding -ls -execdir cat {} \; 18926 0 -rw-r--r-- 1 root root 0 Mar 5 13:31 /proc/sys/net/ipv4/conf/all/forwarding 1 18954 0 -rw-r--r-- 1 root root 0 Mar 5 13:31 /proc/sys/net/ipv4/conf/default/forwarding 1 18978 0 -rw-r--r-- 1 root root 0 Mar 5 13:31 /proc/sys/net/ipv4/conf/eth0/forwarding 1 19003 0 -rw-r--r-- 1 root root 0 Mar 5 13:31 /proc/sys/net/ipv4/conf/lo/forwarding 1 19028 0 -rw-r--r-- 1 root root 0 Mar 5 13:31 /proc/sys/net/ipv4/conf/tun0/forwarding 1 Client routing table: $ netstat -r Routing tables Internet: Destination Gateway Flags Refs Use Netif Expire 0/1 10.8.0.5 UGSc 8 48 tun0 default 192.168.1.1 UGSc 2 1652 en1 10.8.0.1/32 10.8.0.5 UGSc 1 0 tun0 10.8.0.5 10.8.0.6 UHr 13 0 tun0 10.10.0/24 10.8.0.5 UGSc 0 0 tun0 <snip> Traceroute from client: $ traceroute 10.10.0.9 traceroute to 10.10.0.9 (10.10.0.9), 64 hops max, 52 byte packets 1 10.8.0.1 (10.8.0.1) 5.403 ms 1.173 ms 1.086 ms 2 192.168.1.1 (192.168.1.1) 4.693 ms 2.110 ms 1.990 ms 3 l100.my-verizon-garbage (client-ext-ip) 7.453 ms 7.089 ms 6.248 ms 4 * * * 5 10.10.0.9 (10.10.0.9) 14.915 ms !N * 6.620 ms !N

Read the article

Nginx Multiple Domains

- by showFocus

I am trying to add a second virtual host to nginx. When i go to the new domain it redirects to the old one. I have tried restarting Nginx, rebooting the server. Has anyone come across this before, care to share? File: nginx.conf ### user www-data www-data; worker_processes 4; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; sendfile on; tcp_nopush on; tcp_nodelay off; keepalive_timeout 5; gzip on; gzip_comp_level 2; gzip_proxied any; gzip_types text/plain text/css application/x-javascript text/xml application/xml application/xml+rss text/javascript; include /usr/local/nginx/sites-enabled/*; } File: ../sites-enabled/domain1.co.uk server { listen 80; server_name www.domain1.co.uk; rewrite ^/(.*) http://domain1.co.uk/$1 permanent; } server { listen 80; server_name domain1.co.uk; access_log /home/me/public_html/domain1.co.uk/log/access.log; error_log /home/me/public_html/domain1.co.uk/log/error.log; location / { root /home/me/public_html/domain1.co.uk/public/; index index.php index.html; # WordPress supercache & permalinks. include /usr/local/nginx/conf/wordpress_params.super_cache; } # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; include /usr/local/nginx/conf/fastcgi_params; fastcgi_param SCRIPT_FILENAME /home/me/public_html/domain1.co.uk/public/$fastcgi_script_name; } } File: ../sites-enabled/domain2.co.uk server { listen 80; server_name www.domain2.co.uk; rewrite ^/(.*) http://domain2.co.uk/$1 permanent; } server { listen 80; server_name domain2.co.uk; access_log /home/me/public_html/domain2.co.uk/log/access.log; error_log /home/me/public_html/domain2.co.uk/log/error.log; location / { root /home/me/public_html/domain2.co.uk/public/; index index.php index.html; # Basic version of WordPress parameters, supporting nice permalinks. # include /usr/local/nginx/conf/wordpress_params.regular; # Advanced version of WordPress parameters supporting nice permalinks and WP Super Cache plugin include /usr/local/nginx/conf/wordpress_params.super_cache; } # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 # location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; include /usr/local/nginx/conf/fastcgi_params; fastcgi_param SCRIPT_FILENAME /home/me/public_html/domain2/public/$fastcgi_script_name; } }

Read the article

Installing .NET application on IIS 7.5 issues

- by Juw

Really need some help here. I am at a loss. I am trying to install a webservice that some other guy wrote in .NET. I have some basic IIS understanding. The webservice works just fine on my dev computer. But now i try to move the webservice to a production server and bad things happens. The webservice has been located in C:\inetpub\wwwroot\ dir on the dev server. But on this production server it is to be located in D:\services\ I have managed to install an application on the production server and everything seems fine and dandy. But when i "Test Settings" in the initial setup i get "Invalid application path" error. But i can just close it down and still install it. But when i try to access the webservice with: http://myserver.com/webservice/GetData nothing happens. Just a blank page and when i check the response headers...500 error. I don´t know what is going on here or where the problem is. I post the config file here so someone hopefully might notice something odd. Thanx in advance! EDIT: The config file is from my dev server. I just copied it to my production server...but that obviously didn´t work :-) UPDATE: I noticed that my dev server run in an Application pool with Net 4 and in "classic" "mode". On the production server it was in NET 4 but in "integrated" mode. So i changed it to "classic". I still get a blank page. But checking the log will output this: 2012-10-03 14:57:00 ip removed GET /boo/GetData - 80 - ip removed Mozilla/5.0+(Windows+NT+6.1;+WOW64;+rv:15.0)+Gecko/20100101+Firefox/15.0.1 404 2 1260 203 <?xml version="1.0" encoding="UTF-8"?> <configuration> <system.web> <identity impersonate="true" />  <compilation targetFramework="4.0"> <assemblies> <add assembly="System.Data.Entity, Version=4.0.0.0, Culture=neutral, PublicKeyToken=b7735c561131e089" /> </assemblies> </compilation> <pages controlRenderingCompatibilityVersion="3.5" clientIDMode="AutoID" /> </system.web> <system.webServer> <modules runAllManagedModulesForAllRequests="true" /> <httpErrors existingResponse="PassThrough" /> <httpProtocol> <customHeaders> <add name="Access-Control-Allow-Origin" value="*" /> </customHeaders> </httpProtocol> <directoryBrowse enabled="false" /> </system.webServer> <system.serviceModel> <serviceHostingEnvironment aspNetCompatibilityEnabled="true" /> <standardEndpoints> <webHttpEndpoint>  <standardEndpoint name="" helpEnabled="true" automaticFormatSelectionEnabled="true" /> </webHttpEndpoint> </standardEndpoints> </system.serviceModel> <connectionStrings> <add name="Entities" connectionString="metadata=res://*/DataModel.csdl|res://*/DataModel.ssdl|res://*/DataModel.msl;provider=System.Data.SqlClient;provider connection string="data source=someip;initial catalog=db_90;User ID=user1;Password=access2;multipleactiveresultsets=True;App=EntityFramework"" providerName="System.Data.EntityClient" /> </connectionStrings> </configuration>

Read the article

How to open a server port outside of an OpenVPN tunnel with a pf firewall on OSX (BSD)

- by Timbo

I have a Mac mini that I use as a media server running XBMC and serves media from my NAS to my stereo and TV (which has been color calibrated with a Spyder3Express, happy). The Mac runs OSX 10.8.2 and the internet connection is tunneled for general privacy over OpenVPN through Tunnelblick. I believe my anonymous VPN provider pushes "redirect_gateway" to OpenVPN/Tunnelblick because when on it effectively tunnels all non-LAN traffic in- and outbound. As an unwanted side effect that also opens the boxes server ports unprotected to the outside world and bypasses my firewall-router (Netgear SRX5308). I have run nmap from outside the LAN on the VPN IP and the server ports on the mini are clearly visible and connectable. The mini has the following ports open: ssh/22, ARD/5900 and 8080+9090 for the XBMC iOS client Constellation. I also have Synology NAS which apart from LAN file serving over AFP and WebDAV only serves up an OpenVPN/1194 and a PPTP/1732 server. When outside of the LAN I connect to this from my laptop over OpenVPN and over PPTP from my iPhone. I only want to connect through AFP/548 from the mini to the NAS. The border firewall (SRX5308) just works excellently, stable and with a very high throughput when streaming from various VOD services. My connection is a 100/10 with a close to theoretical max throughput. The ruleset is as follows Inbound: PPTP/1723 Allow always to 10.0.0.40 (NAS/VPN server) from a restricted IP range >corresponding to possible cell provider range OpenVPN/1194 Allow always to 10.0.0.40 (NAS/VPN server) from any Outbound: Default outbound policy: Allow Always OpenVPN/1194 TCP Allow always from 10.0.0.40 (NAS) to a.b.8.1-a.b.8.254 (VPN provider) OpenVPN/1194 UDP Allow always to 10.0.0.40 (NAS) to a.b.8.1-a.b.8.254 (VPN provider) Block always from NAS to any On the Mini I have disabled the OSX Application Level Firewall because it throws popups which don't remember my choices from one time to another and that's annoying on a media server. Instead I run Little Snitch which controls outgoing connections nicely on an application level. I have configured the excellent OSX builtin firewall pf (from BSD) as follows pf.conf (Apple App firewall tie-ins removed) (# replaced with % to avoid formatting errors) ### macro name for external interface. eth_if = "en0" vpn_if = "tap0" ### wifi_if = "en1" ### %usb_if = "en3" ext_if = $eth_if LAN="{10.0.0.0/24}" ### General housekeeping rules ### ### Drop all blocked packets silently set block-policy drop ### all incoming traffic on external interface is normalized and fragmented ### packets are reassembled. scrub in on $ext_if all fragment reassemble scrub in on $vpn_if all fragment reassemble scrub out all ### exercise antispoofing on the external interface, but add the local ### loopback interface as an exception, to prevent services utilizing the ### local loop from being blocked accidentally. ### set skip on lo0 antispoof for $ext_if inet antispoof for $vpn_if inet ### spoofing protection for all interfaces block in quick from urpf-failed ############################# block all ### Access to the mini server over ssh/22 and remote desktop/5900 from LAN/en0 only pass in on $eth_if proto tcp from $LAN to any port {22, 5900, 8080, 9090} ### Allow all udp and icmp also, necessary for Constellation. Could be tightened. pass on $eth_if proto {udp, icmp} from $LAN to any ### Allow AFP to 10.0.0.40 (NAS) pass out on $eth_if proto tcp from any to 10.0.0.40 port 548 ### Allow OpenVPN tunnel setup over unprotected link (en0) only to VPN provider IPs ### and port ranges pass on $eth_if proto tcp from any to a.b.8.0/24 port 1194:1201 ### OpenVPN Tunnel rules. All traffic allowed out, only in to ports 4100-4110 ### Outgoing pings ok pass in on $vpn_if proto {tcp, udp} from any to any port 4100:4110 pass out on $vpn_if proto {tcp, udp, icmp} from any to any So what are my goals and what does the above setup achieve? (until you tell me otherwise :) 1) Full LAN access to the above ports on the mini/media server (including through my own VPN server) 2) All internet traffic from the mini/media server is anonymized and tunneled over VPN 3) If OpenVPN/Tunnelblick on the mini drops the connection, nothing is leaked both because of pf and the router outgoing ruleset. It can't even do a DNS lookup through the router. So what do I have to hide with all this? Nothing much really, I just got carried away trying to stop port scans through the VPN tunnel :) In any case this setup works perfectly and it is very stable. The Problem at last! I want to run a minecraft server and I installed that on a separate user account on the mini server (user=mc) to keep things partitioned. I don't want this server accessible through the anonymized VPN tunnel because there are lots more port scans and hacking attempts through that than over my regular IP and I don't trust java in general. So I added the following pf rule on the mini: ### Allow Minecraft public through user mc pass in on $eth_if proto {tcp,udp} from any to any port 24983 user mc pass out on $eth_if proto {tcp, udp} from any to any user mc And these additions on the border firewall: Inbound: Allow always TCP/UDP from any to 10.0.0.40 (NAS) Outbound: Allow always TCP port 80 from 10.0.0.40 to any (needed for online account checkups) This works fine but only when the OpenVPN/Tunnelblick tunnel is down. When up no connection is possbile to the minecraft server from outside of LAN. inside LAN is always OK. Everything else functions as intended. I believe the redirect_gateway push is close to the root of the problem, but I want to keep that specific VPN provider because of the fantastic throughput, price and service. The Solution? How can I open up the minecraft server port outside of the tunnel so it's only available over en0 not the VPN tunnel? Should I a static route? But I don't know which IPs will be connecting...stumbles How secure would to estimate this setup to be and do you have other improvements to share? I've searched extensively in the last few days to no avail...If you've read this far I bet you know the answer :)

Read the article

ISP 5 Device Limit ... again

- by Tommo

Sorry for the delay in responding to the suggestions that were posted in my first question (ISP 5 Device Limit - double NAT the solution?). I've been travelling and have not been able to try anything. Below is what I've tried and where I have not been successful. Any more help gratefully appreciated. I figure I need to give a more comprehensive overview of what I've got and how it's set up. First of all - I am using all Apple products here. I am iMac, iPad, iPhone, Apple TV, Airport Express and Time Capsule. I used to like the way that it 'just worked'. Now I find that it requires a bit of encouragement before it 'just works'. So, as I stated in my original question; my ISP has a router in my building that is limiting me to 5 devices. I am hard wired into this router and I can neither access it physically nor logically (they won't let me access it). Also, I only appear to be able to connect to it through the LAN ports on my Time Capsule. Any device I connect appears to be on a rolling IP list with the following settings: Router 91.72.80.1 Devices then get assigned IPv4 addresses in the range (as far as I can see) from 91.72.80.2 onwards. SubNet Mask 255.255.255.0 DNS Servers 213.132.63.25, 80.227.2.4 I have my Time Capsule / Router in Bridge-Mode which means I am limited to the 5 devices and cannot use Guest Networks etc. What I've tried today. Static IPs: On all devices, I went from DHCP to Static and put in the same information when they had connected using DHCP. Somewhat surprisingly this did not work. None of the devices enjoyed any connection to the router and certainly no internet connection. Intentional Double-NAT - Time Capsule to 'DHCP and NAT': By selecting DHCP and NAT on my Router I was able to connect devices to my Time Capsule in the range 10.0.1.2 to 10.0.1.200. This offered no internet connectivity and didn't really help the situation. In this mode, however, I was able to force the devices - individually and laboriously - to look for the Router and previously listed DNSs by inputting the numbers from 'Bridge-mode' into the STATIC settings and then resetting the connection. The Router then appeared to assign a distinct IP address to the device and it worked on the network. I had this working for more than 5 devices. However, this is not a great solution because as soon as one of the mobile devices left the building it needed repointing to the Router. The connections were also not very stable. Especially when trying to hold onto a VPN. Spoofing a few MAC addresses: I'm afraid I don't really know what this would achieve, nor how to do it on an Apple device… So … I'm almost back at Square One. I have had to withdraw to the Bridge-Mode position again with the 5 device limit to see if there's a better course of action to follow. ANY help would be much appreciated. I am positive that I cannot be the only one suffering under this 5 device limit!

Read the article

Configuring nginx server to handle requests from multiple domains

- by KillABug

Use Case:- I am working on a web application which allows to create HTML templates and publish them on amazon S3.Now to publish the websites I use nginx as a proxy server. What the proxy server does is,when a user enters the website URL,I want to identify how to check if the request comes from my application i.e app.mysite.com(This won't change) and route it to apache for regular access,if its coming from some other domain like a regular URL www.mysite.com(This needs to be handled dynamically.Can be random) it goes to the S3 bucket that hosts the template. My current configuration is: user nginx; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log main; charset utf-8; keepalive_timeout 65; server_tokens off; sendfile on; tcp_nopush on; tcp_nodelay off; Default Server Block to catch undefined host names server { listen 80; server_name app.mysite.com; access_log off; error_log off; location / { proxy_pass http://127.0.0.1:8080; proxy_set_header X-Real-IP $remote_addr; proxy_set_header Host $host; proxy_redirect off; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 90; client_max_body_size 10m; client_body_buffer_size 128k; proxy_buffer_size 4k; proxy_buffers 4 32k; proxy_busy_buffers_size 64k; } } } Load all the sites include /etc/nginx/conf.d/*.conf; Updates as I was not clear enough :- My question is how can I handle both the domains in the config file.My nginx is a proxy server on port 80 on an EC2 instance.This also hosts my application that runs on apache on a differnet port.So any request coming for my application will come from a domain app.mysite.com and I also want to proxy the hosted templates on S3 which are inside a bucket say sites.mysite.com/coolsite.com/index.html.So if someone hits coolsite.com I want to proxy it to the folder sites.mysite.com/coolsite.com/index.html and not to app.syartee.com.Hope I am clear The other server block: # Server for S3 server { # Listen on port 80 for all IPs associated with your machine listen 80; # Catch all other server names server_name _; //I want it to handle other domains then app.mysite.com # This code gets the host without www. in front and places it inside # the $host_without_www variable # If someone requests www.coolsite.com, then $host_without_www will have the value coolsite.com set $host_without_www $host; if ($host ~* www\.(.*)) { set $host_without_www $1; } location / { # This code rewrites the original request, and adds the host without www in front # E.g. if someone requests # /directory/file.ext?param=value # from the coolsite.com site the request is rewritten to # /coolsite.com/directory/file.ext?param=value set $foo 'http://sites.mysite.com'; # echo "$foo"; rewrite ^(.*)$ $foo/$host_without_www$1 break; # The rewritten request is passed to S3 proxy_pass http://sites.mysite.com; include /etc/nginx/proxy_params; } } Also I understand I will have to make the DNS changes in the cname of the domain.I guess I will have to add app.mysite.com under the CNAME of the template domain name?Please correct if wrong. Thank you for your time

Read the article

website connection reset on first load

- by Tar

i'm using nginx with php-cgi. lately a problem has arose where if you don't view my site for a while, like 3-4 minutes, and then open it again, the first request you send will return connection reset by peer in the browser. if you refresh, operation is normal for all subsequent requests. this happens every time and it isn't just an isolated incident, it happens to everyone using my site. i've tried to restart nginx and php-cgi but to no avail. does anyone know what the problem could be? i can provide whatever information necessary. it's worth noting that there's nothing in error log besides that message about client closing the connection early. nginx.conf user nobody; worker_processes 4; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 2048; } http { include /etc/nginx/mime.types; error_page 404 /404.html; error_page 403 /403.html; error_page 444 /444.html; error_page 502 /502.html; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log main; large_client_header_buffers 8 8k; sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 30; server_tokens off; gzip on; gzip_proxied any; gzip_comp_level 6; gzip_buffers 64 8k; gzip_min_length 1024; gzip_http_version 1.1; gzip_types text/plain text/css application/json application/x-javascript text/xml application/xml application/xml+rss text/javascript; include /etc/nginx/conf.d/*.conf; } default.conf server { listen 80; server_name domain.com; error_log /var/log/nginx/error.log debug; access_log /var/log/nginx/access.log; location / { if ($request_method !~ ^(GET|HEAD|POST)$ ) { return 444; } if ($http_user_agent ~* Havij|hvj|acunetix|wget|HTtrack) { return 403; } root /home/admin06/public_html; autoindex off; index index.php; # Images and static content is treated different location ~* ^.+.(jpg|jpeg|gif|css|png|js|ico|xml)$ { access_log off; expires 30d; root /home/admin06/public_html; } location /nginx_status { stub_status on; access_log off;] deny all; } location ~ \.php$ { fastcgi_split_path_info ^(.+\.php)(/.*)$; #try_files $uri =404; fastcgi_pass backend; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /home/site/public_html$fastcgi_script_name; include fastcgi_params; fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_intercept_errors on; fastcgi_ignore_client_abort off; fastcgi_connect_timeout 60; fastcgi_send_timeout 60; fastcgi_read_timeout 60; fastcgi_buffer_size 128k; fastcgi_buffers 4 256k; fastcgi_busy_buffers_size 256k; fastcgi_temp_file_write_size 256k; } ## Disable viewing .htaccess & .htpassword location ~ /\.ht { deny all; } location ~ error_log { deny all; } location ~ access_log { deny all; } location ~ \.cgi { deny all; } location ~ \.db { deny all; } }

Read the article

Is this valid JFS partition?

- by Coolmax

This is my first question on StackExchange. My teacher gave my his laptop (with Fedora 16 on it) and compact flash card with data. He want to have access to files on card, but he couldn't get access to it. The problem is Linux don't know what type of partion is. I suppose there is JFS: root@debian:~# dmesg |grep sdc [ 9066.908223] sd 3:0:0:1: [sdc] 3940272 512-byte logical blocks: (2.01 GB/1.87 GiB) [ 9066.962307] sd 3:0:0:1: [sdc] Write Protect is off [ 9066.962310] sd 3:0:0:1: [sdc] Mode Sense: 03 00 00 00 [ 9066.962312] sd 3:0:0:1: [sdc] Assuming drive cache: write through [ 9067.028420] sd 3:0:0:1: [sdc] Assuming drive cache: write through [ 9067.028637] sdc: unknown partition table [ 9067.097065] sd 3:0:0:1: [sdc] Assuming drive cache: write through [ 9067.097281] sd 3:0:0:1: [sdc] Attached SCSI removable disk and some of data: root@debian:~# hexdump -Cn 65536 /dev/sdc 00000000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 00008000 4a 46 53 31 01 00 00 00 48 63 0e 00 00 00 00 00 |JFS1....Hc......| 00008010 00 10 00 00 0c 00 03 00 00 02 00 00 09 00 00 00 |................| 00008020 00 20 00 00 00 09 20 10 02 00 00 00 00 00 00 00 |. .... .........| 00008030 04 00 00 00 26 00 00 00 02 00 00 00 24 00 00 00 |....&.......$...| 00008040 41 03 00 00 16 00 00 00 00 02 00 00 a0 cc 01 00 |A...............| 00008050 37 00 00 00 69 cc 01 00 b6 d8 ac 4b 00 00 00 00 |7...i......K....| 00008060 32 00 00 00 02 00 00 00 00 00 00 00 00 00 00 00 |2...............| 00008070 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| 00008080 00 00 00 00 00 00 00 00 90 15 e5 5f e3 c4 45 fa |..........._..E.| 00008090 9d 6a 5c b5 4f da 62 1a 00 00 00 00 00 00 00 00 |.j\.O.b.........| 000080a0 00 00 00 00 00 00 00 00 c3 c9 01 00 ed 81 00 00 |................| 000080b0 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| 000080c0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * [cut] * 0000f000 4a 46 53 31 01 00 00 00 48 63 0e 00 00 00 00 00 |JFS1....Hc......| 0000f010 00 10 00 00 0c 00 03 00 00 02 00 00 09 00 00 00 |................| 0000f020 00 20 00 00 00 09 20 10 00 00 00 00 00 00 00 00 |. .... .........| 0000f030 04 00 00 00 26 00 00 00 02 00 00 00 24 00 00 00 |....&.......$...| 0000f040 41 03 00 00 16 00 00 00 00 02 00 00 a0 cc 01 00 |A...............| 0000f050 37 00 00 00 69 cc 01 00 b6 d8 ac 4b 00 00 00 00 |7...i......K....| 0000f060 32 00 00 00 02 00 00 00 00 00 00 00 00 00 00 00 |2...............| 0000f070 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| 0000f080 00 00 00 00 00 00 00 00 90 15 e5 5f e3 c4 45 fa |..........._..E.| 0000f090 9d 6a 5c b5 4f da 62 1a 00 00 00 00 00 00 00 00 |.j\.O.b.........| 0000f0a0 00 00 00 00 00 00 00 00 c3 c9 01 00 ed 81 00 00 |................| 0000f0b0 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| 0000f0c0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 00010000 I'm total newbie to filesystems. I googled and found that JFS superblock may starts on 0x8000 offset. But what next? How to mount this card? If there would be normal partition table I would expect 55 AA on 510th and 511th byte, but first 8000 bytes are clear. Any help would be greatly appreciated. And sorry for my bad english :) Kind regards.

Read the article

KVM with one host IP and a different subnet for machines

- by Jguy

I've already setup a KVM host with proper IP configurations, but my host had me create DHCP and use that to assign the IP's to the machines. I want to see if there's an easier way to do it (or better). Upon my first setting out on this, I didn't find anything that pointed me in the right direction. I'm coming off a fresh install of Debian 6.0 x64, so I have nothing installed. I've logged in, queried for the below information and changed the password from my host set one. I have a Debian 6.0 x64 system with the following initial network configuration (substituted 255 in place of my real first octave): # tail /etc/network/interfaces auto eth0 iface eth0 inet static address 255.9.24.80 broadcast 255.9.24.95 netmask 255.255.255.224 gateway 255.9.24.65 # default route to access subnet up route add -net 255.9.24.64 netmask 255.255.255.224 gw 255.9.24.65 eth0 I have a /29 subnet that I want the virtual machines to use from my host: IP: 255.46.187.152 /29 Mask: 255.255.255.248 Broadcast: 255.46.187.159 Usable IP addresses: 255.46.187.153 to 255.46.187.158 I like the interface of Cloudmin, so I want to try and use that if I can to administrate my guests. So, my questions: How do I set this up on the host system the best so that I can use the additional Subnet IP's on the guests and have them accessible from the internet? I also need to host a DNS server, which means one of these VM's has to have two IP's assigned to it and accessable from the outside world. How can I do that using Cloudmin? I had a question about this here: Multiple IP addresses assigned to one KVM VM But I just reformatted the entire server and am trying to figure out a better way of doing this. Machine information: # ip route show 255.9.24.64/27 via 255.9.24.65 dev eth0 255.9.24.64/27 dev eth0 proto kernel scope link src 255.9.24.80 default via 255.9.24.65 dev eth0 brctl is empty # ip addr list 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether c8:60:00:54:b5:d8 brd ff:ff:ff:ff:ff:ff inet 255.9.24.80/27 brd 255.9.24.95 scope global eth0 inet6 fe80::ca60:ff:fe54:b5d8/64 scope link valid_lft forever preferred_lft forever Thank you for any help you can provide me. EDIT: I've installed kvm and cloudmin: aptitude install qemu-kvm libvirt-bin wget http://cloudmin.virtualmin.com/gpl/scripts/cloudmin-kvm-debian-install.sh ./cloudmin-kvm-debian-install.sh Rebooted and now my network configuration looks like this: # device: eth0 iface eth0 inet manual # default route to access subnet iface br0 inet static address 255.9.24.80 netmask 255.255.255.224 broadcast 255.9.24.95 network 255.9.24.64 bridge_ports eth0 gateway 255.9.24.65 I setup in Cloudmin the Start IP as 255.46.187.153 and End IP as 255.46.187.158. The CIDR is 29 and the gateway is 255.46.187.152. I've installed a guest with ubuntuserver 12.04 x64, which was able to get and retrieve internet resources during installation, but now cannot reach anything nor can it be reached from anything. Its network configuration is: iface eth0 inet static address 255.46.187.153 netmask 255.255.255.224 broadcast 255.46.187.159 gateway 255.46.187.152 dns-nameservers <host provided nameservers> And is not able to ping google.com through DNS or direct IP, I can't ping the VM from the outside or the host. any ideas now?

Read the article

How can I make subversion reset the stored passwords/users and remember my authentication credential

- by NicDumZ

Hello folks! Background: I used to have everything working just fine on my fresh install: $ svn co https://domain:443/ test1 Error validating server certificate for 'https://domain:443': - The certificate is not issued by a trusted authority. Use the fingerprint to validate the certificate manually! Certificate information: - Hostname: **REMOVED** - Valid: **REMOVED** - Issuer: **REMOVED** - Fingerprint: **checked with issuer and REMOVED** (R)eject, accept (t)emporarily or accept (p)ermanently? p Authentication realm: <https://domain:443> Subversion repository Password for 'nicdumz-machine-hostname': Authentication realm: <https://domain:443> Subversion repository Username: nicdumz Password for 'nicdumz': # proceeds to checkout correctly $ svn co https://domain:443/ test2 # checkouts nicely, without asking for my password. At some point I needed to commit stuff using a different account. So I did that $ svn ci --username other.user Authentication realm: <https://domain:443> Subversion repository Password for 'other.user': # works fine But since then, everytime I want to commit as 'nicdumz' (default user, all repos have been checked-out with that user), it prompts me for my password: $ svn ci Authentication realm: <https://domain:443> Subversion repository Password for 'nicdumz': Hey come on, why :) The same happens if I want a fresh checkout, since read-access is also protected. So I tried fixing the issue by myself. I read around that ~/.subversion/auth was storing credentials, so I removed it from the way: $ cd ~/.subversion $ mv auth oldauth $ mkdir auth It seemed to work at first, because svn had forgotten about certificate validation: $ svn co https://domain:443/ test3 Error validating server certificate for 'https://domain:443': - The certificate is not issued by a trusted authority. Use the fingerprint to validate the certificate manually! Certificate information: - Hostname: **REMOVED** - Valid: **REMOVED** - Issuer: **REMOVED** - Fingerprint: **checked with issuer and REMOVED** (R)eject, accept (t)emporarily or accept (p)ermanently? p Authentication realm: <https://domain:443> Subversion repository Password for 'nicdumz-machine-hostname': Authentication realm: <https://domain:443> Subversion repository Username: nicdumz Password for 'nicdumz': # proceeds to checkout correctly $ svn up Authentication realm: <https://domain:443> Subversion repository Password for 'nicdumz': What? how is this happening? If you have suggestions to investigate more about the behaviour, I am very interested. If I'm correct, there is no way to do a verbose svn up or anything of the like, so I'm not sure should I go for investigation. Oh, and for what it's worth: $ svn --version svn, version 1.6.6 (r40053) compiled Oct 26 2009, 06:19:08 Copyright (C) 2000-2009 CollabNet. Subversion is open source software, see http://subversion.tigris.org/ This product includes software developed by CollabNet (http://www.Collab.Net/). The following repository access (RA) modules are available: * ra_neon : Module for accessing a repository via WebDAV protocol using Neon. - handles 'http' scheme - handles 'https' scheme * ra_svn : Module for accessing a repository using the svn network protocol. - with Cyrus SASL authentication - handles 'svn' scheme * ra_local : Module for accessing a repository on local disk. - handles 'file' scheme * ra_serf : Module for accessing a repository via WebDAV protocol using serf. - handles 'http' scheme - handles 'https' scheme

Read the article

Hosed Windows 7 permissons

- by Anthony

Here is the most interesting thing I've noticed since the problems started: If I go into a control panel/system module (in this case the Resource Monitor) that has a "Check Online" type option, Firefox (my default browser) opens right up without a problem. But if I just start Firefox from any shortcuts (start menu, desktop, etc), the Firefox process starts up (and the start menu icon starts glowing) only to end without notice a few seconds later. Possibly related: If I start up in Safe-Mode (w/o Networking, but haven't tried with yet), I can start up FF or Chrome just fine, but if I attempt to open Chrome normally, I get a permissions error. Opera and Safari seem to be okay (mostly). Safari crashes when I try to download any files. All of the above leads me to believe that some (but clearly not all) core files have messed up permissions. Or rather, that I no longer have permission. System still does, based on Firefox opening without fail when the system initiates it. I've run MS Forefront once in normal mode, Malwarebytes twice in normal mode and once in safe-mode. One trojan found and deleted, but the problem persists. Two other things worth mentioning: I accidentally duplicated my library... I thought I'd try to add the "Internet" folder to my start menu, next to music and downloads. The first advanced thing I tried was "create new library". I clearly misunderstood what this means. I thought it was a way to add virtual folders to the library (which I thought, in turn, would allow me to choose it as a link on the start menu), but instead it recreated my already existing user folder, AppData and all. I didn't notice this until today. Then I tried setting permissions for my User folder to full control, recursively... Confused but not giving up,I thought I could maybe create a shortcut to the NetHood folder manually, but instead got hit with an access denied error. So I tried to change the permission levels for all sub-folders to my user folder so that I had full control. I got several access denied errors along the way. At this point I gave up, went out, ended up caught in the rain and stuck on a friend's couch and showing up late for work the next day. Thanks for nothing, Microsoft. When I finally got home today (20 hours later), I noticed that Firefox was acting really strange. I tried opening Chrome to see if the problem was client side or server side, and instead got the above-mentioned "you don't have permission to open this program" alert. And I think that's the whole story. Oh, I also did a system restore, but not chose a point from this morning (an auto update), and it worked but the problem wasn't fixed. And then all the earlier restore points were gone. So the questions are: a) is there a way to set the admin and user privs back to "default"? b) would this, in anyone's expert opinion, fix the problems I'm having? c) how come being logged in as an admin isn't the same as being logged in with admin privs? It seems that half the time I have to do run as admin for fairy standard things because i'm being treated as me-theuser and not me-theadmin. Thanks for reading.

Read the article

How to make XAMPP virtual hosts accessible to VM's and other computers on LAN?

- by martin's

XAMPP running on Vista 64 Ultimate dev machine (don't think it matters). Machine / Browser configuration Safari, Firefox, Chrome and IE9 on dev machine IE7 and IE8 on separate XP Pro VM's (VMWare on dev machine) IE10 and Chrome on Windows 8 VM (VMware on dev machine) Safari, Firefox and Chrome running on a iMac (same network as dev) Safari, Firefox and Chrome running on a couple of Mac Pro's (same network as dev) IE7, IE8, IE9 running on other PC's on the same network as dev machine Development Configuration Multiple virtual hosts for different projects .local fake TLD for development No firewall restrictions on dev machine for Apache Some sites have .htaccess mapping www to non-www Port 80 is open in the dev machine's firewall Problem XAMPP local home page (http://192.168.1.98/xampp/) can be accessed from everywhere, real or virtual, by IP All .local sites can be accessed from the browsers on the dev machine. All .local sites can be accessed form the browsers in the XP VM's. Some .local sites cannot be accessed from IE10 or Chrome on the W8 VM Sites that cannot be accessed from W8 VM have a minimal .htaccess file No .local sites can be accessed from ANY machine (PC or Mac) on the LAN hosts on dev machine (relevant excerpt) 127.0.0.1 site1.local 127.0.0.1 site2.local 127.0.0.1 site3.local 127.0.0.1 site4.local 127.0.0.1 site5.local 127.0.0.1 site6.local 127.0.0.1 site7.local 127.0.0.1 site8.local 127.0.0.1 site9.local 192.168.1.98 site1.local 192.168.1.98 site2.local 192.168.1.98 site3.local 192.168.1.98 site4.local 192.168.1.98 site5.local 192.168.1.98 site6.local 192.168.1.98 site7.local 192.168.1.98 site8.local 192.168.1.98 site9.local httpd-vhosts.conf on dev machine (relevant excerpt) NameVirtualHost *:80 <VirtualHost *:80> ServerName localhost ServerAlias localhost *.localhost.* DocumentRoot D:/xampp/htdocs </VirtualHost> # ======================================== site1.local <VirtualHost *:80> ServerName site1.local ServerAlias site1.local *.site1.local DocumentRoot D:/xampp-sites/site1/public_html ErrorLog D:/xampp-sites/site1/logs/access.log CustomLog D:/xampp-sites/site1/logs/error.log combined <Directory D:/xampp-sites/site1> Options Indexes FollowSymLinks AllowOverride All Require all granted </Directory> </VirtualHost> NOTE: The above <VirtualHost *:80> block is repeated for each of the nine virtual hosts in the file, no sense in posting it here. hosts on all VM's and physical machines on the network (relevant excerpt) 127.0.0.1 localhost ::1 localhost 192.168.1.98 site1.local 192.168.1.98 site2.local 192.168.1.98 site3.local 192.168.1.98 site4.local 192.168.1.98 site5.local 192.168.1.98 site6.local 192.168.1.98 site7.local 192.168.1.98 site8.local 192.168.1.98 site9.local None of the VM's have any firewall blocks on http traffic. They can reach any site on the real Internet. The same is true of the real machines on the network. The biggest puzzle perhaps is that the W8 VM actually DOES reach some of the virtual hosts. It does NOT reach site2, site6 and site 9, all of which have this minimal .htaccess file. .htaccess file <IfModule mod_rewrite.c> RewriteEngine On RewriteCond %{HTTP_HOST} !^www\. RewriteRule ^(.*)$ http://www.%{HTTP_HOST}/$1 [R=301,L] </IfModule> Adding this file to any of the virtual hosts that do work on the W8 VM will break the site (only for W8 VM, not the XP VM's) and require a cache flush on the W8 VM before it will see the site again after deleting the file. Regardless of whether a .htaccess file exists or not, no machine on the same LAN can access anything other than the XAMPP home page via IP. Even with hosts files on all machines. I can ping any virtual host from any machine on the network and get a response from the correct IP address. I can't see anything in out Netgear router that might prevent one machine from reaching the other. Besides, once the local hosts file resolves to an ip address that's all that goes out onto the local network. I've gone through an extensive number of posts on both SO and as the result of Google searches. I can't say that I have found anything definitive anywhere.

Read the article

I am getting a 400 Bad Request error when using Nginx and PHP-FPM, why?

- by Bob

I am trying to run a website (that requires PHP - it technically doesn't require MySQL at this time, but it may sometime in the near future as I continue developing it, so I went ahead and installed that as well) using nginx 1.2.4 and PHP-FPM 5.3.3 on Ubuntu 12.04.1 LTS. As far as I know, I haven't done anything wrong, but clearly something is not quite right - I seem to be getting a 400 Bad Request error whenever I try to browse to my website. I've been mostly following one guide, and I've done more or less everything it recommends, except for not setting up PHP-FPM to use a Unix Socket and I used service as opposed to /etc/init.d/ when starting/stopping nginx, PHP, and MySQL. Anyways, here are my relevant configuration files (I have only censored personal/sensitive details, like my domain name - which contains my real name): /etc/nginx/nginx.conf user www-data; worker_processes 4; pid /var/run/nginx.pid; events { worker_connections 768; # multi_accept on; } http { ## # Basic Settings ## sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 15; types_hash_max_size 2048; # server_tokens off; # server_names_hash_bucket_size 64; # server_name_in_redirect off; include /etc/nginx/mime.types; default_type application/octet-stream; ## # Logging Settings ## access_log /var/log/nginx/access.log; error_log /var/log/nginx/error.log; ## # Gzip Settings ## gzip on; gzip_disable "msie6"; # gzip_vary on; # gzip_proxied any; # gzip_comp_level 6; # gzip_buffers 16 8k; # gzip_http_version 1.1; # gzip_types text/plain text/css application/json application/x-javascript text/xml application/xml application/xml+rss text/javascript; ## # nginx-naxsi config ## # Uncomment it if you installed nginx-naxsi ## #include /etc/nginx/naxsi_core.rules; ## # nginx-passenger config ## # Uncomment it if you installed nginx-passenger ## #passenger_root /usr; #passenger_ruby /usr/bin/ruby; ## # Virtual Host Configs ## include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } /etc/nginx/sites-enabled/subdomain.mydomain.net server { listen 80; # listen for IPv4 listen [::]:80; # listen for IPv6 server_name www.subdomain.mydomain.net subdomain.mydomain.net; access_log /srv/www/subdomain.mydomain.net/logs/access.log; error_log /srv/www/subdomain.mydomain.net/logs/error.log; location / { root /srv/www/subdomain.mydomain.net/public; index index.php; } location ~ \.php$ { try_files $uri =400; include fastcgi_params; fastcgi_split_path_info ^(.+\.php)(/.+)$; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /srv/www/subdomain.mydomain.net/public$fastcgi_script_name; } } All the directories listed in the configuration files above are correct on my server (to the extent of my knowledge). I have not included /etc/php5/fpm/pool.d/www.conf or /etc/php5/fpm/php.ini in this post as they're rather long, but I have posted them on Pastebin: http://pastebin.com/ensErJD8 and http://pastebin.com/T23dt7vM, respectively. Although, the only thing I've changed in either of the two files was in php.ini, where I set expose_php to off so as to hide the .php file extension from users. What can I do to resolve my issue? Please let me know if I need to supply any additional details.

Read the article

Set up lnux box for hosting a-z [apache mysql php ssl]

- by microchasm

I am in the process of reinstalling the OS on a machine that will be used to host a couple of apps for our business. The apps will be local only; access from external clients will be via vpn only. The prior setup used a hosting control panel (Plesk) for most of the admin, and I was looking at using another similar piece of software for the reinstall - but I figured I should finally learn how it all works. I can do most of the things the software would do for me, but am unclear on the symbiosis of it all. This is all an attempt to further distance myself from the land of Configuration Programmer/Programmer, if at all possible. I can't find a full walkthrough anywhere for what I'm looking for, so I thought I'd put up this question, and if people can help me on the way I will edit this with the answers, and document my progress/pitfalls. Hopefully someday this will help someone down the line. The details: CentOS 5.5 x86_64 httpd: Apache/2.2.3 mysql: 5.0.77 (to be upgraded) php: 5.1 (to be upgraded) The requirements: SECURITY!! Secure file transfer Secure client access (SSL Certs and CA) Secure data storage Virtualhosts/multiple subdomains Local email would be nice, but not critical The Steps: Download latest CentOS DVD-iso (torrent worked great for me). Install CentOS: While going through the install, I checked the Server Components option thinking I was going to be using another Plesk-like admin. In hindsight, considering I've decided to try to go my own way, this probably wasn't the best idea. Basic config: Setup users, networking/ip address etc. Yum update/upgrade. Upgrade PHP: To upgrade PHP to the latest version, I had to look to another repo outside CentOS. IUS looks great and I'm happy I found it! cd /tmp #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm #rpm -Uvh epel-release-1-1.ius.el5.noarch.rpm #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-4.ius.el5.noarch.rpm #rpm -Uvh ius-release-1-4.ius.el5.noarch.rpm yum list | grep -w \.ius\. [will list all packages available in the IUS repo] rpm -qa | grep php [will list installed packages needed to be removed. the installed packages need to be removed before you can install the IUS packages otherwise there will be conflicts] #yum shell >remove php-gd php-cli php-odbc php-mbstring php-pdo php php-xml php-common php-ldap php-mysql php-imap Setting up Remove Process >install php53 php53-mcrypt php53-mysql php53-cli php53-common php53-ldap php53-imap php53-devel >transaction solve >transaction run Leaving Shell #php -v PHP 5.3.2 (cli) (built: Apr 6 2010 18:13:45) This process removes the old version of PHP and installs the latest. To upgrade mysql: Pretty much the same process as above with PHP #/etc/init.d/mysqld stop [OK] rpm -qa | grep mysql [installed mysql packages] #yum shell >remove mysql mysql-server Setting up Remove Process >install mysql51 mysql51-server mysql51-devel >transaction solve >transaction run Leaving Shell #service mysqld start [OK] #mysql -v Server version: 5.1.42-ius Distributed by The IUS Community Project And this is where I'm at. I will keep editing this as I make progress. Any tips on how to Configure Virtualhosts for SSL, setting up a CA, setting up SFTP with openSSH, or anything else would be appreciated.

Read the article

Windows 7, file properties - Is "date accessed" ALWAYS 100% accurate?

- by Robert

Hello, Here's the situation: I went on vacation for a couple of weeks, but before I left, I took the harddrive out of my computer and hid it in a different location. Upon coming back on Monday and putting the harddrive back in my computer, I right-clicked on different files to see their properties. Interestingly enough, several files had been accessed during the time I was gone! I right-clicked different files in various locations on the harddrive, and all of these suspect files had been accessed within a certain time range (Sunday, ?January ?09, ?2011, approximately ??between 6:52:16 PM - 7:16:25 PM). Some of them had been accessed at the exact same time--down to the very second. This makes me think that someone must have done a search on my harddrive for certain types of files and then copied all those files to some other medium. The Windows 7 installation on this harddrive is password protected, but NOT encrypted, so they could have easily put the harddrive into an enclosure/toaster to access it from a different computer. Of course I did not right-click every single file on my computer, but did so in different folders. For instance, one of the folders I went through has different types of files: .mp3, ,prproj, .3gp, .mpg, .wmv, .xmp, .txt with file-sizes ranging from 2 KB to 29.7 MB (there is also a sub-folder in this folder which contains only .jpg files); however, of all these different types of files in this folder and its subfolder, all of them had been accessed (including the .jpg files from the sub-folder) EXCEPT the .mp3 files (if it makes any difference, the .mp3 files in this folder range in size from 187 KB to 4881 KB). Additionally, this sub-folder which contained only .jpg files (48 .jpg files to be exact) was not accessed during this time--only the .jpg files within it were accessed-- (between 6:57:03 PM - 6:57:08 PM). I thought that perhaps this was some kind of Windows glitch that was displaying the wrong access date, but then I looked at the "date created" and "date modified" for all of these files in question, and their created/modified dates and times were spot on correct. My first thought was that someone put the harddrive into an enclosure/toaster and viewed the files; but then I realized that this was impossible because several of the files had been accessed at the same exact time down to the second. So this made me think that the only other way the "date accessed" could have changed would have been if someone copied the files. Is there any chance at all whatsoever that this is some kind of Windows glitch or something, or is it a fact that someone was indeed accessing my files (and if someone was accessing my files, am I right about the files in question having been copied)? Is there any other possibility for what could have happened? Do I need to use any kinds of forensics tools to further investigate this matter (and if so, which tools), or is there any other way in which I can be certain of what took place in that timeframe the day before I got back? Or is what I see with Windows 7 good enough (i.e. accurate and truthful)? Thanks in advance, and please let me know if any other details are required on my part.

Read the article

How do i route TCP connections via TOR? [on hold]

- by acidzombie24

I was reading about torchat which is essentially an anonymous chat program. It sounded cool so i wanted to experiment with making my own. First i wrote a test to grab a webpage using Http. Sicne .NET doesnt support SOCKS4A/SOCKS5 i used privoxy and my app worked. Then i switch to a TCP echo test and privoxy doesnt support TCP so i searched and installed 6+ proxy apps (freecap, socat, freeproxy, delegate are the ones i can remember from the top of my head, i also played with putty bc i know it supports tunnels and SOCK5) but i couldnt successfully get any of them to work let alone get it running with my http test that privoxy easily and painlessly did. What may i use to get TCP connections going through TOR? I spent more then 2 hours without success. I don't know if i am looking for a relay, tunnel, forwarder, proxy or a proxychain which all came up in my search. I use the config below for .NET. I need TCP working but i am first testing with http since i know i had it working using privoxy. What apps and configs do i use to get TCP going through tor? <?xml version="1.0" encoding="utf-8" ?> <configuration> <system.net> <defaultProxy enabled="true"> <proxy bypassonlocal="True" proxyaddress="http://127.0.0.1:8118"/> </defaultProxy> <settings> <httpWebRequest useUnsafeHeaderParsing="true"/> </settings> </system.net> </configuration> -edit- Thanks to Bernd i have a solution. Here is the code i ended up writing. It isn't amazing but its fair. static NetworkStream ConnectSocksProxy(string proxyDomain, short proxyPort, string host, short hostPort, TcpClient tc) { tc.Connect(proxyDomain, proxyPort); if (System.Text.RegularExpressions.Regex.IsMatch(host, @"[\:/\\]")) throw new Exception("Invalid Host name. Use FQDN such as www.google.com. Do not have http, a port or / in it"); NetworkStream ns = tc.GetStream(); var HostNameBuf = new ASCIIEncoding().GetBytes(host); var HostPortBuf = BitConverter.GetBytes(IPAddress.HostToNetworkOrder(hostPort)); if (true) //5 { var bufout = new byte[128]; var buflen = 0; ns.Write(new byte[] { 5, 1, 0 }, 0, 3); buflen = ns.Read(bufout, 0, bufout.Length); if (buflen != 2 || bufout[0] != 5 || bufout[1] != 0) throw new Exception(); var buf = new byte[] { 5, 1, 0, 3, (byte)HostNameBuf.Length }; var mem = new MemoryStream(); mem.Write(buf, 0, buf.Length); mem.Write(HostNameBuf, 0, HostNameBuf.Length); mem.Write(new byte[] { HostPortBuf[0], HostPortBuf[1] }, 0, 2); var memarr = mem.ToArray(); ns.Write(memarr, 0, memarr.Length); buflen = ns.Read(bufout, 0, bufout.Length); if (bufout[0] != 5 || bufout[1] != 0) throw new Exception(); } else //4a { var bufout = new byte[128]; var buflen = 0; var mem = new MemoryStream(); mem.WriteByte(4); mem.WriteByte(1); mem.Write(HostPortBuf, 0, 2); mem.Write(BitConverter.GetBytes(IPAddress.HostToNetworkOrder(1)), 0, 4); mem.WriteByte(0); mem.Write(HostNameBuf, 0, HostNameBuf.Length); mem.WriteByte(0); var memarr = mem.ToArray(); ns.Write(memarr, 0, memarr.Length); buflen = ns.Read(bufout, 0, bufout.Length); if (buflen != 8 || bufout[0] != 0 || bufout[1] != 90) throw new Exception(); } return ns; } Usage using (TcpClient client = new TcpClient()) using (var ns = ConnectSocksProxy("127.0.0.1", 9050, "website.com", 80, client)) {...}

Read the article

Network update solutions for a company of ~20 (5 local, 15 remote)?

- by Margaret

Hi all This is probably going to be a bit up in the air, because we're still in the "reaching towards solutions" phase, but I figured I'd see what you guys had to say. Plus I honestly know very little about systems and what is good and bad pratice. My organisation has always more or less worked on the concept of local machines; since it primarily employed contractors who were working from home, each of those people was largely responsible for their own machine and backup procedures and the like. We're now expanding, though we're still reasonably small (we're up to about 20 staff members). Most people still work remotely, but we have a central office where about five people are working. But we're getting large enough that we're starting to think it would be a good idea to have a central file server, and things like that - if someone gets hit by a bus, we want someone else to know where to look for the files to continue their work. A lot of the people who work for us remotely work on projects for other companies as well, so I don't want to force them to log in to our server whenever they're on a network. But I do want to make connection to be as painless as possible to do so, to improve utilisation. The other thing is that we're getting more people who would like to remote into the office server and do their work there. Our current remote connection application is an SSH install that allows people access to the network; the problem is, it's a black box to me, and I've never understood how to even connect to it (despite supposedly being de facto sysadmin). Thus far I've been able to bounce questions about how to get it working to the guy who does know it well, but he's leaving the company soon. So we probably need a solution for this that I actually understand. We were knocking around the idea of implementing a VPN with some form of remote desktop, and someone mentioned that this was largely a matter of purchasing a router capable of it; I'm not sure of the truth of that statement. This is what we have in the office: Two shiny new i7 servers, each running Windows Server 2008. Precise eventual layout is still being debated, a little, but the current suggestion is that one is primary database crunching, while the other is a warm backup of the databases, along with running Reporting Services. They currently have SQL Server 2008 installed on them, which is being connected to via the 'sa' account. We're hoping to make each person use their own account (preferably one tied to the 'central' password we set up, so we can use Windows Authentication). An older server, running XP Pro, that we are currently using as a test bed for a project that requires access to older versions of software. This machine is also being used to take backups, but I'm thinking of moving that functionality elsewhere. A spare desktop from a guy who left the company (XP Pro). We're thinking of bumping up the hard disk space and using it as the magical file server that's going to solve one particular everything. Assorted desktops, laptops, etc, at least one for each person in the office (mix of Win XP and Win 7; occasionally a person who normally works remotely might drop in to the office and bring a laptop bearing Vista, but it's pretty rare). All are set up as local user accounts at the moment; I don't know if it's the best arrangement. Purchasing more hardware is not a big problem, but we figure we might as well make use of what we've got first. Is Active Directory a big magic wand that's going to solve all the world's problems? Is there some other arrangement we should be looking to instead?

Read the article

Android RatingBar weirdness: Whenever I add a RatingBar to my layout, a bunch of the generated tags,

- by Rben

Whenever I use a RatingBar view in my layout, I suddenly get all kinds of compile errors. I'm using Android 2.0, but I've also tried 2.0.1, and 2.1, without joy. I also get a message: Shader 'android.graphics.BitmapShader' is not supported in Layout Editor, and an odd warning which may or maynot be related: warning: Ignoring InnerClasses attribute for an anonymous inner class that doesn't come with an associated EnclosingMethod attribute. I've tried using the RatingBar both within a tablelayout and outside it, but it behaves the same way. This is very puzzling and frustrating. Please help if you can. Sincerely, Ray Here's the XML:  <TableRow android:layout_height="wrap_content" android:layout_width="fill_parent" > <TextView android:text="Created by: " android:id="@+id/gi_created_label" android:layout_width="wrap_content" android:layout_height="wrap_content" android:gravity="right" /> <TextView android:text="Slartibartfast" android:id="@+id/gi_created" android:layout_width="fill_parent" android:layout_height="wrap_content" /> </TableRow>  <TableRow android:layout_height="wrap_content" android:layout_width="fill_parent" > <TextView android:id="@+id/gi_verification_label" android:layout_width="wrap_content" android:layout_height="wrap_content" android:gravity="right" android:text="@string/GameInfoVerificationLabelText" /> <TextView android:id="@+id/gi_verification" android:layout_width="fill_parent" android:layout_height="wrap_content" android:text="HonorSystem" /> </TableRow>  <TableRow android:layout_height="wrap_content" android:layout_width="fill_parent" > <TextView android:layout_width="fill_parent" android:layout_height="wrap_content" android:gravity="right" android:text="@string/GameInfoPlayerRatingLabel" /> <TextView android:layout_width="fill_parent" android:layout_height="wrap_content" android:text=" " /> </TableRow> --  <TableRow android:layout_height="wrap_content" android:layout_width="fill_parent" > <TextView android:id="@+id/gi_times_played_label" android:layout_width="wrap_content" android:layout_height="wrap_content" android:gravity="right" android:text="@string/GameInfoTimesPlayedLabel" /> <TextView android:id="@+id/gi_times_played" android:layout_width="fill_parent" android:layout_height="wrap_content" android:text="999" /> </TableRow>  <TableRow android:layout_height="wrap_content" android:layout_width="fill_parent" > <TextView android:id="@+id/gi_total_players_label" android:layout_width="wrap_content" android:layout_height="wrap_content" android:gravity="right" android:text="@string/GameInfoTotalPlayerCountLabel" /> <TextView android:id="@+id/gi_total_players" android:layout_width="fill_parent" android:layout_height="wrap_content" android:text="999" /> </TableRow>  <TableRow android:layout_height="wrap_content" android:layout_width="fill_parent" > <TextView android:id="@+id/gi_total_cancelations_label" android:layout_width="wrap_content" android:layout_height="wrap_content" android:gravity="right" android:text="@string/GameInfoTotalCancelsLabel" /> <TextView android:id="@+id/gi_total_cancels" android:layout_width="fill_parent" android:layout_height="wrap_content" android:text="999" /> </TableRow> <RatingBar android:id="@+/gi_player_rating" style="?android:attr/ratingBarStyleSmall" android:layout_width="wrap_content" android:layout_height="wrap_content" android:layout_span="2" android:isIndicator="true" android:numStars="5" android:rating="3" android:stepSize="1" android:layout_gravity="center_vertical" /> </TableRow>

Read the article

SOA PARTNER COMMUNITY NEWSLETTER JULY 2012

- by mseika

SOA PARTNER COMMUNITY NEWSLETTER JULY 2012 Dear SOA partner community member To provide our community members the best of our knowledge, we want your feedback on our SOA Partner community. Thus we are organizing SOA Partner Community Survey 2012. We request you to participate in the survey and give your valuable feedback on various areas of marketing, sales and education. To continue our successful BPM Suite, Oracle is launching together with you Process Accelerators initiative. It’s your opportunity to co-develop and market predefined processes. Oracle Fusion Applications Design Patterns are a great tool to develop your SOA or BPM solution or process accelerators. To promote your SOA & BPM Specialization we continue to offer several benefits. This month we would like to highlight our Specialization Plaques - make sure you request one for your office! Our Fusion Middleware Summer Camps are booked out, if could not get a seat you can attend the SOA & BPM track @ Virtual Developer Day: Oracle Fusion Development Oracle demo systems offer´s two new demos: Business Driven Development based on BPM Suite & SOA Lifecycle Management. Jürgen KressOracle SOA & BPM Partner Adoption EMEA NEW CONTENT Community SurveyProcess Accelerators KitPlaques SOA & BPM SpecializedSOA & BPM at Virtual Developer Day News from our Partners & CommunityOverview of SOA Diagnostics in 11.1.1.6 Business driven development(BDD) demo now available! SOA Lifecycle Management Oracle Fusion applications design patterns Updated material by Oracle Connect and Network SOA Blogs SOA on Facebook SOA on LinkedIn SOA on Twitter Mix SOA Forum COMMUNITY SURVEY Like every year we would like to get your feedback in our SOA Partner Community Survey 2012. Make sure that You attend to further develop our community and support our planning! It is key for us to get your feedback to prepare for the next fiscal year. Back to top PROCESS ACCELERATORS KIT Oracle is very interested to co-develop and market with you, our partners, pre-defined processes for BPM Suite.I am very happy to announce a new program called “Oracle BPM Partner Solution Catalog”. This program will provide a one-stop shop for our customers looking for Oracle BPM partner solutions available in the market today.The Oracle BPM Solution Catalog will be hosted on our very popular Oracle Technology Network (OTN). To give you an idea of the scale of customer visibility, OTN today receives over 1Million hits per day from our business and developer community. We would like to invite you to list your Oracle BPM 11g solutions available today.In order to participate in this program, you need to do the following: Fill in the attached slide templates - #3 and #4 for each Oracle BPM 11g solution you would like to list on OTN.Please add links to whitepapers , videos, references to the specific solution in the template slide. We recommend that you create a landing page on your website for these linked artifacts and just point to the same from within the PowerPoint template. This will give you the flexibility to update the information as frequently as needed. If you have the particular solution in production or a reference available, please list them as well. Send the PowerPoint template slides (1 set of slides for each Oracle BPM solution) to [email protected]. In addition to having the opportunity to list your solutions on OTN for Oracle customers, you will have the chance to advertise your new wins/implementations/solutions in an Oracle Sponsored PM Webinar held every quarter. This program is targeted to go live by the end of summer 2012. At this point, we are targeting a soft launch in July end 2012 so send on your BPM solutions information as soon as possible. We would love to have your solution(s) listed in the “Oracle BPM Partner Solution Catalog” at the time of the launch. This will be a live repository so you can keep adding more solutions as they become available. If you have any questions, please feel free to contact us [email protected], Product Strategy Director, Oracle BPM , Phone +1 650.506.5486.Thank you and look forward to hearing from you. Oracle BPM team Process Accelerators Overview.pdf ProcessAcceleratorsDataSheet.pdf Demos draUPK.zip & trmUPK.zip BPM Solution repository slides.ppt Additional BPM material BPM Process Development Lifecycle Document that describes recommended approach to collaborative process modeling across business and IT tools ADF 11g PS5 Application with Customized BPM Worklist Task Flow (MDS Seeded Customization) by Andrejus Baranovskis BPMN process editor problems in 11.1.1.6 by Mark Nelson BPM – Disable DBMS job to refresh B2B Materialized View by Mark Nelson For the complete kit please visit the BPM folder at our SOA Community Workspace (SOA Community membership required). For the complete presentation please visit our SOA Community Workspace (SOA Community membership required). Information is Oracle and Partner confidential! Back to top PLAQUES SOA & BPM SPECIALIZED We continue to offer you a nice SOA & BPM Specialization plaque with your logo to proof your success. If you are a SOA or BPM Specialized partner and would like to request the plaque please send Brigitte an e-mail with the following information: Partner Name Partner logo (preferred eps file) Partner Status gold or platinum Your shipping address Your Specialization: SOA or BPM We recommend to mount the plaque at your office reception in addition you can use the SOA Specialization logos at your website download Logo: Gold & Platinum or the BPM logos Gold & Platinum Back to top SOA & BPM AT VIRTUAL DEVELOPER DAY Register now for this FREE hands-on online workshop Get up to date and learn everything you wanted to know about Oracle ADF & Fusion Development plus live Q&A chats with Oracle technical staffOracle Application Development Framework (ADF) is the standards based, strategic framework for Oracle Fusion Applications and Oracle Fusion Middleware. Oracle ADF’s integration with the Oracle SOA Suite, Oracle WebCenter and Oracle BI creates a complete productive development platform for your custom applications.Join us at this FREE virtual event and learn the latest in Fusion Development including: Is Oracle ADF development faster and simpler than Forms, Apex or .Net? Mobile Application Development with ADF Mobile Oracle ADF development with Eclipse Oracle WebCenter Portal and ADF Development Application Lifecycle Management with ADF Building Process Centric Applications with ADF and BPM Oracle Business Intelligence and ADF Integration Live Q&A chats with Oracle technical staff Developer lead, manager or architect - this event has something for everyone. Don’t miss this opportunity.Tuesday, July 10, 2012. 9:00 a.m. PT -1:00 p.m. PT 11:00 a.m. CT - 3:00 p.m. CT 12:00 p.m. ET - 4:00 p.m. ET 1:00 p.m. BRT - 5:00 p.m. BRT Register online now! for this FREE event. Agenda: 09:00 am Opening 09:30 am Keynote: Oracle Fusion Development Track1Introduction to Fusion Development Track2What's New in Fusion Development Track3Fusion Development in the Enterprise 10:00 am Is Oracle ADF Development Faster and Simpler than Oracle Forms, APEX or .Net? Mobile Application Development with ADF Mobile Oracle WebCenter Portal and ADF Development 11:00 am Rich Web UI made simple - an ADF Faces Overview Oracle Enterprise Pack for Eclipse - ADF Development Building Process Centric Applications with ADF and BPM 12:00 noon Next Generation Controller for JSF Application Lifecycle Management for ADF Oracle Business Intelligence and ADF Integration *Hands On Lab – WebCenter and ADF Lab w/ JDeveloper - Lab materials will be provided ahead of the event to give you ample time to work through the lab and increase the productivity of the live chat sessions the day of the event. Sessions abstractsRegister online now! for this FREE event Read more on Community Events and post your comment here. Back to top NEWS FROM OUR PARTNERS AND COMMUNITY Send your tweets @soacommunity #soacommunity and follow us at http://twitter.com/soacommunity JDeveloper & ADF?Troubleshooting BPMN process editor problems in 11.1.1.6http://dlvr.it/1p0FfS SOA Community?SOA & BPM @ Virtual Developer Day: Oracle Fusion Development - July 10th 2012https://soacommunity.wordpress.com/2012/07/02/soa-bpm-virtual-developer-day- oracle-fusion-developmentjuly-10th-2012/#soacommunity #soa #bom #education orclateamsoa ?A-Team Blog #ateam: BAM design pointers - In working recently with a large Oracle customer on SOA and BAM, I discove.http://ow.ly/1kYqES SOA CommunitySOA Community Newsletter June 2012http://wp.me/p10C8u-qw SOA CommunityBPMN process editor problems in 11.1.1.6 by Mark Nelsonhttp://redstack.wordpress.com/2012/06/27/ bpmn-process-editor-problems-in-11-1-1-6 #soacommunity #bpm OTNArchBeat ?SOA Learning Library: free short, topic-focused training on Oracle SOA & BPM products | @SOACommunity http://pub.vitrue.com/NE1G Andrejus Baranovskis ?ADF 11g PS5 Application with Customized BPM Worklist Task Flow (MDS Seeded Customization)http://fb.me/1coX4r1X1 SOA CommunitySOA Learning Library provides a comprehensive curriculum for the SOA and BPM product suites https://soacommunity.wordpress.com/2012/06/27/soa-learning-library #soacommunity #soa #bpm OTNArchBeat ?A Universal JMX Client for Weblogic - Part 1: Monitoring BPEL Thread Pools in SOA 11g | Stefan Koserhttp://pub.vitrue.com/mQVZ OTNArchBeat ?BPM - Disable DBMS job to refresh B2B Materialized View | Mark Nelson http://pub.vitrue.com/3PR0Oracle SOA ?Learn how Choice Hotels Implements Innovative Google Maps Solution with #OracleSOA http://bit.ly/MTwIJ3 SOA Communitytop Tweets SOA Partner Community - June 2012 Send your tweets @soacommunity #soacommunity https://soacommunity.wordpress.com/2012/06/25/top-tweets-soa-partner-community-june-2012 Torsten Winterberg#OPITZ is pushing Oracle commitment to the next level: New Specializations done: ADF, BPM, WLS, Exadatahttp://bit.ly/KX1WVS ServiceTechSymposium ?Only 8 more days left until Super Early Bird Registration Discount expires! http://www.servicetechsymposium.com OracleBlogsSOA Management in 3 minutes - Video explainerhttp://ow.ly/1kN5pn SOA Community ?SOA, Cloud & Service Technology Symposium 2012 London - Enter Promo Code: Djmxz370https://soacommunity.wordpress.com/2012/06/22/soa-cloud-service-technology-symposium-2012-london #soasymposium #soacommunity #soa Heidi BuelowGreat course! w David Read RT @soacommunity: product management ADF for BPM training 5 seats left https://soacommunity.wordpress.com/2012/06/12/fusion-middleware-summer-campsadvanced-partner-trainings/ #bpm #soacommunity SOA Community ?product management ADF for BPM training 5 seats lefthttps://soacommunity.wordpress.com/2012/06/12/fusion-middleware-summer-campsadvanced-partner-trainings/ #bpm #soacommunity OTNArchBeat ?Oacle Fusion Applications Design Patterns Now Available For Developers | Ultan O'Broinhttp://pub.vitrue.com/UEiF OTNArchBeat ?SOA, Cloud & Service Technology Symposium 2012London - Special Oracle Discounthttp://pub.vitrue.com/8E0J SOA CommunityBecome a facebook fan of soacommunity http://www.facebook.com/soacommunity #soacommunity SOA Community ?SOA Suite HealthCare Integration Architecture https://blogs.oracle.com/SOAForHealthcare/entry/soa_suite_healthcare_integration_architecture #soacommunity #soa Andrejus Baranovskis ?Running Pre-built Virtual Machine for SOA Suite and BPM Suite 11g PS5 on Mac OS X Snow Leopard (10.6http://fb.me/vB8nO0Vg OracleBlogsPrinciples of Service-Oriented Architecture by Douwe P. van den Bos http://ow.ly/1kIcOP OTNArchBeatOracle Public Cloud Architecture | @TylerJewell http://ow.ly/bHAcL The SOA Network ?Business Process Management, Service-Oriented Architecture, and Web 2.0: Business Transformation or.http://bit.ly/LBgREL #ITNews #SOA OracleBlogs ?Oracle SOA Foundation Practitioner Certificationhttp://ow.ly/1kGYYg Frank Nimphius ?Learn Advanced ADF. ORACLE Fusion Middleware Summer Camps in Lisbon - July 9th - 13thhttp://bit.ly/KGCl3i SOA CommunityTransform Your Application Integration with Best Practices from Oracle Customershttps://blogs.oracle.com/SOA/entry/transform_your_application_integration_with #soacommunity #soa #bpm Simone GeibWhat you always wanted to know about #oraclesoa diagnostics: Shawn Bailey, Overview of SOA Diagnostics in 11.1.1.6,http://ow.ly/bxK0M Oracle SOA ?Save the date: Jun 21 10AM, SOA & BPM Customer Insight Series. Hear how Choice Hotels went from legacy to #oraclesoa http://bit.ly/LsNDGl OTNArchBeat ?New VirtualBox images for Oracle SOA Suite & Oracle BPM Suite 11.1.1.6.0http://ow.ly/bwDAl OracleBlogs ?Process development lifecycle in Oracle BPM 11g http://ow.ly/1ktesY Daniel AmadeiNew post: Oracle BPEL 11g Message Delivery & Recovery.http://amadei.com.br/blog/index.php /oracle-bpel-11g-message-delivery SOA Community ?Sending out the June edition of the #soacommunity newsletter - read it or become a member http://www.oracle.com/goto/emea/soa!#soa #bpm Arun Pareek ?For the past six months Ahmed Aboulnaga and me have been working on Oracle SOA Suite 11g Administrator's Handbook.http://lnkd.in/CAvpUQ SOA CommunitySun shine all day no clouds - solar eclipse is over... #sunshine #cloud http://www.infoq.com/presentations/Swarm-Computing Michel SchildmeijerWatch my blog Oracle Service Bus 11g: listing projects and services with WLST - part 1 http://lnkd.in/B7f3GQ @TITAN_GS @wlscommunity OTNArchBeatBook Review: Oracle Application Integration Architecture (AIA) Foundation Pack 11gR1: Essentials | Rajesh Rahejahttp://ow.ly/bn2cc OTNArchBeat ?Driving from Business Architecture to Business Process Services | @vghariharan http://ow.ly/bn5UB OTNArchBeat ?SOA Analysis within the Department of Defense Architecture Framework (DoDAF) 2.0 - Part II | Dawit Lessanu http://ow.ly/bn6sX Simone Geib ?Contact me directly for ideas how to improvehttp://bit.ly/advancedsoasuite and additional posts, presentations, white papers, ... #soasuite Simone Geib ?#soasuite advanced OTN page has become too cluttered. Broke it into separate pages to start with. http://bit.ly/advancedsoasuite OracleBlogs ?June Webcast: SOA Gateway Implementation and Troubleshooting (2 sessions) http://ow.ly/1kbRFA ServiceTechSymposium ?New session just posted to calendar: "NoSQL for Data Services, Data Virtualization & Big Data" by Guido Schmutz, Trivadis AG ://ow.ly/bjjOeDebra Lilley ?looks good - real proof people are using the apps ! RT @fteter: Very cool Fusion Applications Help site: http://bit.ly/L3nvOR #FusionApps demed ?rapid proliferation of cloud computing will drive convergence of SOA and cloud paradigms" http://ovum.com/2012/05/18/soa-paves-the-way-for-cloud/ SOA CommunityMiddleware Oracle Excellence Awards 2012-HAPPY NEW YEAR! https://soacommunity.wordpress.com/2012/05/31/middleware-oracle-excellence-awards-2012happy-new-year/ #soacommunity #opn #opnaward #specialization #oracle SOA CommunityHappy New Year #soacommunity thanks for the business! Time for a drink http://pic.twitter.com/zkK08KWB OTNArchBeat ?Who should ‘own’ the Enterprise Architecture? | Michael Glas http://bit.ly/K0ge0Q SOA Communitytop Tweets SOA Partner Community – May 2012 http://wp.me/p10C8u-pP ServiceTechSymposiumNew session just posted to Symposium calendar: "Elastic SOA in the Cloud" by Steve Millidge, C2B2 Consulting http://www.servicetechsymposium.com/agenda2012.php #elastic_soa_in_the_cloud orclateamsoa ?A-Team Blog #ateam: How to Set JVM Parameters in Oracle SOA 11Ghttp://ow.ly/1k2cnl ServiceTechSymposium ?New session just posted to Symposium calendar: "SOA Governance at EDP: A Global Energy Company" by Manuel Rosa, Linkhttp://www.servicetechsymposium.com/agenda2012.php#soa_governance_at_edp SOA Community ?VirtualBox image SOA Suite & BPM Suite 11.1.1.6.0–Your feedback?http://wp.me/p10C8u-qh Oracle MiddlewareSave the date: Jun 21 10AM, SOA & BPM Customer Insight Series. Hear how Choice Hotels went from legacy to#oraclesoa http://bit.ly/LU1y5N OTNArchBeat ?Goodbye, Silos. Hello SOA. | @stephanieoverbyhttp://pub.vitrue.com/NJJO SOA CommunityBPM Standard Edition - to start your BPM project http://wp.me/p10C8u-qj Please feel free to send us your news! And add your blog to our SOA blog wiki. Back to top OVERVIEW OF SOA DIAGNOSTICS IN 11.1.1.6 What tools are available for diagnosing SOA Suite issues? There are a variety of tools available to help you and Support diagnose SOA Suite issues in 11g but it can be confusing as to which tool is appropriate for a particular situation and what their relationships are. This blog post will introduce the various tools and attempt to clarify what each is for and how they are related. Let's first list the tools we'll be addressing: RDA: Remote Diagnostic Agent DFW: Diagnostic Framework Selective Tracing DMS: Dynamic Monitoring Service ODL: Oracle Diagnostic Logging ADR: Automatic Diagnostics Repository ADRCI: Automatic Diagnostics Repository Command Interpreter WLDF: WebLogic Diagnostic Framework This overview is not mean to be a comprehensive guide on using all of these tools, however, extensive reference materials are included that will provide many more details on their execution. Another point to note is that all of these tools are applicable for Fusion Middleware as a whole but specific products may or may not have implemented features to leverage them. A couple of the tools have a WebLogic Scripting Tool or 'WLST' interface. WLST is a command interface for executing pre-built functions and custom scripts against a domain. A detailed WLST tutorial is beyond the scope of this post but you can find general information here. There are more specific resources in the below sections.In this post when we refer to 'Enterprise Manager' or 'EM' we are referring to Enterprise Manager Fusion Middleware Control. read the full blog post here. Read more on Oracle and post your comment here. Back to top BUSINESS DRIVEN DEVELOPMENT (BDD) DEMO NOW AVAILABLE! For access to the Oracle demo systems please visit OPN and talk to your Partner Expert DSS is pleased to announce the availability of the demo “Business Driven Development“. This innovative demonstration uses a case-study approach to show business users how they can easily streamline their Business Processes - delivering greater efficiency, agility, visibility and collaboration with Oracle BPM and WebCenter. The BDD demonstration uses a case study-based approach to highlight a business problem at a fictional company, Avitek Corporation, and uses Oracle BPM and Oracle WebCenter to solve the business problem. This holistic approach has specifically been used to appeal to a non-technical business analyst user. This demo is NOT focused on product features, but aims to guide users through a complete BPM lifecycle. The scenario is based on improving a simple order process (scenario details are in the demo script). Avitek Corporation is sufferinng from a manual email-driven ordering process. Sales reps don’t know where the customer orders are stuck (no visibility) and finance users are unable to manually approve every order (no automation). There are several areas where this process can be improved with Business Process Management technology. This demo shows how improving following areas will ignificantly help resolve the business problems Avitek Corporation is facing. Areas for improvement include: Utilizing BPM for process management, rather than an unregulated, email-based process. Utilizing automated services, rather than requiring a human to key into a system. For example, Finance checking the customer’s credit rating is something that could be automated. Centralizing business rules that can be integrated into a business process, rather than requiring a human to process them. For example, Finance must determine when orders can be automatically approved. Provide insight and visibility into the process. For example, Sales Rep needs to know the status of their customer’s orders. The BDD Demo uses the following products. Oracle BPM Suite 11g PS4FP Oracle WebCenter 11g PS4FP (for Process Spaces) Oracle Business Activity Monitoring 11g Oracle Database 11g Back to top SOA LIFECYCLE MANAGEMENT For access to the Oracle demo systems please visit OPN and talk to your Partner Expert We are pleased to announce the availability of the SOA Management demo that showcases some of the key provisioning and lifecycle management capabilities of SOA Management Pack Enterprise Edition (EE). This demo specifically focuses on some of the lifecycle management solutions for Oracle SOA Suite and Oracle Service Bus (OSB). Demo Highlights The demo showcases the following capabilities. Provisioning of SOA Composites Provisioning of OSB Projects Provision SOA and OSB artifacts in a future maintenance window Back to top ORACLE FUSION APPLICATIONS DESIGN PATTERNS The Oracle Fusion Applications user experience design patterns are published! These new, reusable usability solutions and best-practices, which will join the Oracle dashboard patterns and guidelines that are already available online, are used by Oracle to artfully bring to life a new standard in the user experience, or UX, of enterprise applications. Now, the Oracle applications development community can benefit from the science behind the Oracle Fusion Applications user experience, too. These Oracle Fusion Applications UX Design Patterns, or blueprints, enable Oracle applications developers and system implementers everywhere to leverage professional usability insight when: tailoring an Oracle Fusion application, creating coexistence solutions that existing users will be delighted with, thus enabling graceful user transitions to Oracle Fusion Applications down the road, or designing exciting, new, highly usable applications in the cloud or on-premise. Based on the Oracle Application Development Framework (ADF) components, the Oracle Fusion Applications patterns and guidelines are proven with real users and in the Applications UX usability labs, so you can get right to work coding productivity-enhancing designs that provide an advantage for your entire business. What’s the best way to get started? We’ve made that easy, too. The Design Filter Tool (DeFT) selects the best pattern for your user type and task. Simply adapt your selection for your own task flow and content, and you’re on your way to a really great applications user experience. More Oracle applications design patterns and training are coming your way in the future. To provide feedback on the sets that are currently available, let me know in the comments! Read more on Fusionapps and post your comment here. Back to top UPDATED ORACLE MATERIAL Integrated SOA Gateway Documentation - Implementation Guide | Developer’s Guide Webcast Series: Oracle’s SOA and Oracle Business Process Management Solutions (Choice Hotels, Eaton, Farmers Insurance) BAM design pointers By Kavitha Srinivasan Seeking Oracle Fusion Middleware Go Live StoriesOracle Fusion Middleware product management is looking for recent go live stories to share with the Oracle sales team, sales consulting, product management and other internal groups. Customer contact details may remain anonymous. Your successful implementation will be featured in a quarterly report. The chance to present on an internal webcast is also available. Contact Maria Forney ([email protected]) if you have a noteworthy implementation success story. This is a good opportunity for partners interested in showcasing Oracle Fusion Middleware implementations, and gaining more exposure within Oracle. Performance tuning resources. All in one: docs, blogs, WPs, ppts: http://bit.ly/soa_resources Back to top HAVE YOU MISSED OUR LAST SOA PARTNER COMMUNITY WEBCASTS? UPK Webcast Business Driven Application Management & BPM11g & Application Grid & GoldenGate & Fusion Middleware Pricing & OC4J to WebLogic & Next Generation SOA & Fusion Middleware in Utility & Fusion Middleware in Communications & Fusion Middleware in Public Services & Fusion Middleware in Financial Services Please check your local OPN trainings calendar for additional training dates and locations. Back to top SOA PARTNER COMMUNITY CALENDAR On-Demand Trainings Event Name Language Type SOA Virtual Developers Day English Tech In-Class Trainings Date Event name Location / Country Contact person Type 09-13.07.2012 BPM Suite 11g advanced training by David Read Lisbon, Portugal Jürgen Kress Tech 09-13.07.2012 ADF 11g advanced training by Grant Ronald and Frank Nimphius Lisbon, Portugal Jürgen Kress Tech 09-13.07.2012 WebCenter Portal advanced training by Stefan Krantz and Angelo Santagata Lisbon, Portugal Jürgen Kress Tech 10.07.2012 Fusion Middleware Virtual Developer Day Online OTN Tech 10- 12.07.2012 WebLogic 12c training by Cosmin Tudor Lisbon, Portugal Jürgen Kress Tech 16-18.07.2012 SOA Suite 11g advanced training by Niall Commiskey Munich, Germany Jürgen Kress Tech 16-18.07.2012 ADF for BPM Suite 11g advanced training by David Read Munich, Germany Jürgen Kress Tech 16-18.07.2012 WebCenter Sites 11g advanced training by Product Management Munich, Germany Jürgen Kress Tech 17-20.07.2012 Oracle BPM 11g Implementation Bootcamp Live Virtual Class Oracle University Tech 23-26.07.2012 Oracle BPM 11g Implementation Bootcamp Utrecht, Netherlands Oracle University Tech 29-31.08.2012 Oracle BPM 11g Implementation Bootcamp Live Virtual Class Oracle University Tech 02-05.10.2012 Oracle BPM 11g Implementation Bootcamp Utrecht, Netherlands Oracle University Tech 15-18.10.2012 Oracle BPM 11g Implementation Bootcamp Utrecht, Netherlands Oracle University Tech 28-30.11.2012 Oracle AIA 11g Implementation Bootcamp Live Virtual Class Oracle University Tech 11-14.12.2012 Oracle BPM 11g Implementation Bootcamp Live Virtual Class Oracle University Tech 20-22.2.2013 Oracle AIA 11g Implementation Bootcamp Utrecht, Netherlands Oracle University Tech 14-17.1.2013 Oracle BPM 11g Implementation Bootcamp Utrecht, Netherlands Oracle University Tech 15-18.3.2013 Oracle BPM 11g Implementation Bootcamp Utrecht, Netherlands Oracle University Tech Please check your local OPN Training Calendar for additional training and locations here. Back to top SOASCHOOL.COM - SOA CERTIFIED PROFESSIONAL(SOACP) PROGRAM The SOASchool.com - SOA Certified Professional (SOACP) program is dedicated to excellence in the field of SOA and service-oriented computing. Through a series of seasoned course modules and exams, IT professionals have the opportunity to obtain a number of different certifications to recognize their accomplishment of gaining "project ready" SOA proficiency. This comprehensive and strictly vendor-neutral program was developed in cooperation with best-selling SOA author Thomas Erl and several major SOA organizations and academic institutions. Through the involvement of the SOA Education Committee, course contents and certification requirements are constantly reviewed and revised to stay current with developments in the service-oriented computing industry. The program is currently comprised of 12 course modules and 5 certifications and is expanding to 18 course modules and 8 certifications throughout 2009. For more information, visit www.soaschool.com and www.soacp.com. Blog Twitter LinkedIn Mix Forum Wiki Back to top YOUR CONTENT ON THE NEWSLETTER AND ON THE SOA COMMUNITY PORTAL Publishing Your StoriesWe would like to invite our partners to publish information in the newsletter or on our SOA Community portal. Especially we are looking for your real life experience with our SOA technology. Please send your documents to Jürgen Kress. We look forward to getting your suggestions! Back to top SOA DISCUSSION FORUM BECOMES INTERACTIVE AT THE SOA COMMUNITY! Do you want to chat to experts, including partners and Oracle SOA Product Development? Do you want to get the latest information about our SOA solutions and events?Attend our private online SOA Discussion Forum at OTN. Please send your OTN forums user name to Brigitte Felisaz. You must be a registered user to access the SOA Discussion Forum. Back to top INVITE YOUR COLLEAGUES TO JOIN THE SOA COMMUNITY Please feel free to invite your colleagues to join the SOA Community and to participate in the SOA Assessment tests. For registration please login the Oracle PartnerNetwork and go to: www.oracle.com/goto/emea/soa For any questions on the above or concerning SOA and Oracle in general please contact the Oracle EMEA Alliances & Channels SOA Team. Best regardsOracle EMEA SOA TeamJürgen Kress Jürgen KressSOA Partner Adoption EMEATel. +49 89 1430 1479E-Mail: [email protected]

Read the article

This task is currently locked by a running workflow and cannot be edited. Limitation to both Nintex and SPD workflow

- by ybbest

Note, this post is from Nintex Forum here. These limitations apply to both SharePoint designer Workflow and Nintex Workflow as Nintex using the SharePoint workflow engine. The common cause that I experience is that ‘parent’ workflow is generating more than one task at once. This is common as you can have multiple approvers for certain approval process. You could also have workflow running when the task is created, one of the common scenario is you would like to set a custom column value in your approval task. For me this is huge limitation, as Nintex lover I really hope Nintex could solve this problem with Microsoft going forward. Introduction “This task is currently locked by a running workflow and cannot be edited” is a common message that is seen when an error occurs while the SharePoint workflow engine is processing a task item associated with a workflow. When a workflow processes a task normally, the following sequence of events is expected to occur: 1. The process begins. 2. The workflow places a ‘lock’ on the task so nothing else can change the values while the workflow is processing. 3. The workflow processes the task. 4. The lock is released when the task processing is finished. When the message is encountered, it usually indicates that an error occurred between step 2 and 4. As a result, the lock is never released. Therefore, the ‘task locked’ message is not an error itself, rather a symptom of another error – the ‘task locked’ message does not indicate what went wrong. In most cases, once this message is encountered, the workflow cannot be made to continue and must be terminated and started again. The following is a guide that can help troubleshoot the cause of these messages. Some initial observations to narrow down the potential causes are: Is the error consistent or intermittent? When the error is consistent, it will happen every time the workflow is run. When it is intermittent, it may happen regularly, but not every time. Does the error occur the first time the user tries to respond to a task, or do they respond and notice the workflow does not continue, and when they respond again the error occurs? If the message is present when the user first responds to the task, the issue would have occurred when the task was created. Otherwise, it would have occurred when the user attempted to respond to the task. Causes Modifying the task list A cause of this error appearing consistently the first time a user tries to respond to a task is a modification to the default task list schema. For example, changing the ‘Assigned to’ field in a task list to be a multiple selection will cause the behaviour. Deleting the workflow task then restoring it from the Recycle bin If you start a workflow, delete the workflow task then restore it from the Recycle Bin in SharePoint, the workflow will fail with the ‘task locked’ error. This is confirmed behaviour whether using a SharePoint Designer or a Nintex workflow. You will need to terminate the workflow and start it again. Parallel simultaneous responses A cause of this error appearing inconsistently is multiple users responding to tasks in parallel at the same time. In this scenario, one task will complete correctly and the other will not process. When the user tries again, the ‘task locked’ message will display. Nintex included a workaround for this issue in build 11000. In build 11000 and later, one of the users will receive a message on the task form when they attempt to respond, stating that they need to try again in a few moments. Additional processing on the task A cause of this error appearing consistently and inconsistently is having an additional system running on the items in the task list. Some examples include: a workflow running on the task list, an event receiver running on the task list or another automated process querying and updating workflow tasks. Note: This Microsoft help article (http://office.microsoft.com/en-us/sharepointdesigner/HA102376561033.aspx#5) explains creating a workflow that runs on the task list to update a field on the task. Our experience shows that this causes the ‘Task Locked’ issues when the ‘parent’ workflow is generating more than one task at once. Isolated system error If the error is a rare event, or a ‘one off’ event, then an isolated system error may have occurred. For example, if there is a database connectivity issue while the workflow is processing the task response, the task will lock. In this case, the user will respond to a task but the workflow will not continue. When they respond again, the ‘task locked’ message will display. In this case, there will be an error in the SharePoint ULS Logs at the time that the user originally responded. Temporary delay while workflow processes If the workflow is taking a long time to process after a user submits a task, they may notice and try to respond to the task again. They will see the task locked error, but after a number of attempts (or after waiting some time) the task response page eventually indicates the task has been responded to. In this case, nothing actually went wrong, and the error message gives an accurate indication of what is happening – the workflow temporarily locked the task while it was processing. This scenario may occur in a very large workflow, or after the SharePoint application pool has just started. Modifying the task via a web service with an invalid url If the Nintex Workflow web service is used to respond to or delegate a task, the site context part of the url must be a valid alternative access mapping url. For example, if you access the web service via the IP address of the SharePoint server, and the IP address is not a valid AAM, the task can become locked. The workflow has become stuck without any apparent errors This behaviour can occur as a result of a bug in the SharePoint 2010 workflow engine. If you do not have the August 2010 Cumulative Update (or later) for SharePoint, and your workflow uses delays, “Flexi-task”, State machine”, “Task Reminder” actions or variables, you could be affected. Check the SharePoint 2010 Updates site here: http://technet.microsoft.com/en-us/sharepoint/ff800847. The October CU is recommended http://support.microsoft.com/kb/2553031. The fix is described as “Consider the following scenario. You add a Delay activity to a workflow. Then, you set the duration for the Delay activity. You deploy the workflow in SharePoint Foundation 2010. In this scenario, the workflow is not resumed after the duration of the Delay activity”. If you find this is occurring in your environment, install the October CU, terminate all the running workflows affected and run them afresh. Investigative steps The first step to isolate the issue is to create a new task list on the site and configure the workflow to use it. Any customizations that were made to the original task list should not be made to the new task list. If the new task list eliminates the issue, then the cause can be attributed to the original task list or a change that was made to it. To change the task list that the workflow uses: In Workflow Designer select Settings -> Startup Options Then configure the task list as required If any of the scenarios above do not help, check the SharePoint logs for any messages with a category of ‘Workflow Infrastructure’. Conclusion The information in this article has been gathered from observations and investigations by Nintex. The sources of these issues are the underlying SharePoint workflow engine. This article will be updated if further causes are discovered. From <http://connect.nintex.com/forums/thread/6503.aspx>

Search Results

Search found 33247 results on 1330 pages for 'anonymous access'.

Page 754/1330 | < Previous Page | 750 751 752 753 754 755 756 757 758 759 760 761 | Next Page >

- by Arthur

- by marc.riera

- by dwq

- by aledalgrande

- by Heinrich

- by Sam Martin

- by showFocus

- by Juw

- by Timbo

- by Tommo

- by KillABug

- by Tar

- by Coolmax

- by Jguy

- by NicDumZ

- by Anthony

- by martin's

- by Bob

- by microchasm

- by Robert

- by acidzombie24

- by Margaret

- by Rben

- by mseika

- by ybbest

< Previous Page | 750 751 752 753 754 755 756 757 758 759 760 761 | Next Page >