Search Results

Search found 3463 results on 139 pages for 'physical'.

Page 76/139 | < Previous Page | 72 73 74 75 76 77 78 79 80 81 82 83  | Next Page >

• Planning to buy a server with at least 48GB Ram, are the blades way to go?

  - by varchar1

  We're planning to host our website for the first time for ourselves. We have currently have a linode of 8 gigs and the memory is going up to 90% most of the time. So I want to move my website to my own server with huge RAM. So this will be first time to manage any physical hardware of a server. So I came across IBM's BladeCenter, found them interesting. So can I just buy the blade and run it? Or do I have to buy the chassis for sure? Also, do I need to buy an UPS? So how hard is it to setup? How about the hard drives? Can I setup them easily? Please advice.

  Read the article

• Spanned volumes on new install

  - by Noio

  My Windows 7 Release Candidate is about to expire, so I'm going to do a clean install of a retail version. I have two volumes, on four physical drives, as follows: Disk 0: Spanned Volume (D:) Disk 1: Primary Partition, Boot/Windows Install (C:) Disk 2: Spanned Volume (D:) Disk 3: Spanned Volume (D:) If I install Windows to a formatted drive 1, will it still recognize the spanned volume in Disks 0, 2, and 3? The spanned volume is not redundant in any way, so the volume is 1.5TB consisting of three 500GB disks. I don't have the space to do an external backup, and I thought it was impossible to convert a spanned volume back to a basic volume.

  Read the article

• Adaptec 2020SA RAID controller Set up in RAID5, one drive went down, can I still get data?

  - by SJaguar13

  I have 6 1tb drives in a RAID5. 1 drive went down. On the RAID was 2 virtual machines that I really need back up and running. The spare drive I have to put in the server is a 1.5tb drive, which exceeds the physical per drive limit of the 2020SA. The drive is found in the disk utility, but it is not found in the array management section. I cannot add the drive to the array to have it rebuild. I have a replacement drive along with some spares on their way from Newegg, but I am still looking at a few days of downtime. Is it possible to use the 5 working drives to get the VMs copied off and on to another server or do I just have to wait for the drives to get here?

  Read the article

• Can we put random URL entries on DNS

  - by ring bearer

  Using microsoft DNS All/most of our local hosts ( with in ) are in following domain *.company.org So a host name will look like mymachine001.company.org Is it possible to set up wild card DNS entries of the form ? *.subd.company.com Note: The URL ends with .com, all other hosts so far ever set up in the DNS were of the format *.company.org what i am trying to achieve is the following. A user with in internal network types a url http://someprefix.subd.company.com in browser and enters. Since there is a wild card entry in DNS, the user gets routed to host mapped to *.subd.company.com in the DNS Note : at the same time, company.com has a public DNS entry and that is mapped to a physical IP in some other network (data center)

  Read the article

• Backup virtual hard disk

  - by Harshil Sharma

  I have a VM created in VMWare Player. It's VHD is currently sized 17 GB, split among multiple 2 GB files. The host OS is Windows 8. I use CrashPlan in host OS for file backup. The problem is, whenever I use the VM, CrashPlan detects all parth of VHD as altered and backs up the 17 GB VHD. WHat I want is a software that can run on host OS (Windows 8), treat the VHD as a physical hard disk and create incremental backups of the VHD, includeing all files, programs and the OS

  Read the article

• IIS permissions issue pointing docroot to Samba share

  - by lalalalalalalambda

  I have an IIS project which is stored on a Samba shared, network mounted with the following line: X: \\my-samba-server\dev /user:freddie Connectivity is fine, can read/write files from X:. In IIS, I'm trying to set it as the Physical path via \\my-samba-server\dev\folder\to\my\files, which results in the following 500.19 error: Config Error | Cannot read configuration file due to insufficient permissions It is by default trying to use the Pass-through authentication. If I try to set this to connect as the specific user freddie, I receive: The specified user does not exist What is the correct way to connect to a path which has been setup as described above? *Samba man pages indicate version 3.6 is on the Debian host

  Read the article

• How to get the basic mail command in ubuntu 10 to work

  - by Maureen Adamson

  I am a college lecturer to whom the task of supporting the students' Linux Server has fallen. My students just need to use the mail command to communicate with me and each other. I thought mail would be there by default but it wasn't. I have tried all the advice I found on the Internet and tried to install mailutils, sendmail, mailx, exim4 and postfix. There were more but I can't remember them all now. After installing (if it works - some of them don't), when I try to send a message they all give me: /usr/sbin/sendmail: file or directory not found. I don't need anything fancy - we don't need to access remote email, just locally on our server. Incidentally the same problems are occurring on the physical server and my test virtual machine, installed at different times but both Ubuntu 10. Can anyone help me?

  Read the article

• Create a Windows 7 System Repair ISO?

  - by MaDMaD Mad

  According to the Microsoft website I can run "Create a system repair disc" from the start menu to burn a recovery Disc. However, there are many situations (including not having a disk drive) where this cannot be done. My goal is to create a bootable USB drive according to this guide but their method to do so without burning a physical disc includes downloading an ISO from "somebody's" website. I don't know who "somebody" is and I feel it is reasonable to not boot something I can't verify as being untampered with. To the best of my knowledge, Microsoft does not host a recovery disc ISO for download as this would be the easiest solution. So my problem is that I'd like to circumvent Microsofts "burn to disc" option with a "burn to ISO" through any reasonable means.

  Read the article

• VMware postfix server drops connection

  - by nicoX

  Our physical server godzilla forwards mails to our virtuall VMware server b4. They are on the same net. Often connection drops, we can't ping godzilla with our b4. That means mails from godzilla won't reach b4 and the mails will be in handed into the mailq. Sometimes it takes some hours and the issue will auto fix itself, b4 will wake up and the mail will be delivered. Another thing if we remotely ssh into the b4, the b4 will wake up and and receive any mailq mails from godzilla and deliver them. netadmin@b4:/var/log$ arp -a ? (192.168.209.80) at 00:1E:C9:AE:79:9D [ether] on eth0 root@godzilla:/usr/local/bin# arp -a ? (192.168.209.20) at 00:50:56:91:7d:b2 [ether] on eth0

  Read the article

• Debian 5 is randomly shutting down.

  - by revofreak

  My debian 5 vps is suffering from random shutdowns. I reinstalled it several times, the hosts moved me to a different physical box, check the install image and said everyone else also uses it and is fine. Heres the output from syslog Mar 27 00:19:19 noobintraining-1 -- MARK -- Mar 27 00:32:01 noobintraining-1 shutdown[18142]: shutting down for system halt Mar 27 00:32:06 noobintraining-1 init: Switching to runlevel: 0 Mar 27 00:32:06 noobintraining-1 xinetd[15907]: Exiting... Mar 27 00:32:07 noobintraining-1 named[15865]: received control channel command 'stop -p' Mar 27 00:32:07 noobintraining-1 named[15865]: shutting down: flushing changes Mar 27 00:32:07 noobintraining-1 named[15865]: stopping command channel on 127.0.0.1#953 Mar 27 00:32:07 noobintraining-1 named[15865]: stopping command channel on ::1#953 Mar 27 00:32:07 noobintraining-1 named[15865]: no longer listening on ::#53 Mar 27 00:32:07 noobintraining-1 named[15865]: no longer listening on 127.0.0.1#53 Mar 27 00:32:07 noobintraining-1 named[15865]: no longer listening on 89.238.172.132#53 Mar 27 00:32:07 noobintraining-1 named[15865]: exiting Mar 27 00:32:07 noobintraining-1 exiting on signal 15 Any help is most appreciated!

  Read the article

• Have an iPad's viewable area visible on your computer monitor for remote web-meeting training?

  - by MikeN

  I want to demo the usage of my iPad on my computer screen so that I can transmit it to other people during a training session using a web conference tool (like dimdim.com, gotomeeting.com, fuzemeeting.com, etc...) Is there a way to stream an iPad's display to a computer so it would be visible in such a screen casting software? My current ad-hoc solution for this would be to use a webcam to livecast me using a physical (real life) iPad and broadcast that to other users for training. This is undesirable due to the difficulty in really seeing the iPad well. So I'm hoping someone has a way to do: 1) Video output the iPad's display to my computer screen. 2) Emulate an iPad with a installed app (not having the source code) on the screen.

  Read the article

• How can I resolve this error when using net start / stop: "The service name is invalid" ?

  - by JosephStyons

  We have a server that hosts a service (I'll call it "tomato"). Up until now, a client pc has been able to start and stop this service. They just double-click a batch file, and inside that batch file is the command net stop tomato or net start tomato They recently got a new physical computer, and now those same commands fail with the error: C:\>net stop tomato The service name is invalid. More help is available by typing NET HELPMSG 2185. What do I need to do to let the client pc start and stop this service remotely? Edit: I mis-remembered the original commands. They were not using "net start" and "net stop" remotely. They were using sc \\server_name start tomato and sc \\server_name stop tomato And those commands to indeed still work.

  Read the article

• What's an easy way to shut down a computer that I'm connected to via RDP

  - by MBraedley

  I have a secondary machine on my local network that I usually use via RDP. Most of the time, it's on 24/7, but there are times when I may want to shut it down from the RDP client machine. The shutdown and restart options aren't available from the Windows XP start menu when you connect to a machine via RDP, so how can I shut this machine off without actually going to the physical machine? Also note that this computer currently doesn't have a monitor attached to it, which is partly why I want to be able to shut it down over RDP.

  Read the article

• Memory management (segmentation and paging) in 80286 and 80386: How does it work?

  - by Andrew J. Brehm

  I found lots of Web sites and books explaining how memory management worked on the 8086 and later x86 CPUs in Real Mode. I understand, I think, how two 16 bit values, segment address and offset are combined to get a linear 20 bit physical address (shift segment four bits to the left, add offset; segments are 64K and start every 16 bytes). But I couldn't find any good Web sites or books that explained how memory management works in Protected Mode, specifically the differences between 80286 and 80386. Can anyone point me to a good Web site or book (or explain it right here)? (For extra credit, i.e. an upvote, how does it work in Long Mode?)

  Read the article

• Simple Ubuntu Server - Expanding disk space - adding a new drive LVM, RAID0 existing setup - how?

  - by NightWolf

  I have a 1TB ext4 partition mounted at / with all my data and Ubuntu 11.04 (natty) installed. Now this drive is almost full (I used it as a database server for some processing). RAID0 is ok, I can take a failure (touch wood). But I need a way to grow this partition. I have a new 1TB drive I want to add, however as my Ubuntu boot and all data is on the one partition I'm not sure how I can go about setting up a RAID0 or LVM array without loosing all my data. So the question is how can I extend my existing ext4 partition over two physical drives without losing data? Thanks!

  Read the article

• How to change the amount of RAM displayed in System Properties

  - by Nicu Zecheru

  I have this product that requires at least 1 GB Physical Memory in order to be installed. On my XP Pro machine I have 1 GB of RAM but in System Properties only 0.99 GB of RAM is displayed. The problem is that the product installer checks the memory displayed in System Properties (just a guess, not sure) and cannot continue the setup because it sees only 0.99 GB. Is there any way to change the displayed memory in the System Properties? Or how can I trick the installer to skip the memory check? Thanks.

  Read the article

• How can I change the lock screen in Windows 8 that appears for the default user?

  - by Mark Allen

  This is about Windows 8 RTM. How can I change the lock screen in Windows 8 that appears after connecting to the machine via RDP? You can change your lock screen for your user account like so: Hit the Windows key. Right click your user name in the upper right hand corner, choose Change Account Picture. Click Lock Screen, choose a new picture. However, if you then connect to the computer where you've done this from another computer via RDP, using the same account, the physical machine you've connected to will display the "default" user lock screen - a stylized Space Needle / Seattle picture. It's not a bad picture, but I'd like to change it.

  Read the article

• NTFS write speed really slow (<15MB/s)

  - by Zulakis

  I got a new Seagate 4TB harddrive formatted with ntfs using parted /dev/sda > mklabel gpt > mkpart pri 1 -1 mkfs.ntfs /dev/sda1 When copying files or testing writespeed with dd, the max writespeed I can get is about 12MB/s. The harddrive should be capable of atleast 100MB/s. top shows high cpu usage for the mount.ntfs process. The system has a AMD dualcore. This is the output of parted /dev/sda unit s print: Model: ATA ST4000DM000-1F21 (scsi) Disk /dev/sda: 7814037168s Sector size (logical/physical): 512B/4096B Partition Table: gpt Number Start End Size File system Name Flags 1 2048s 7814035455s 7814033408s pri The used kernel is 3.5.0-23-generic. The ntfs-3g versions I tried are ntfs-3g 2012.1.15AR.1 (ubuntu 12.04 default) and the newest version ntfs-3g 2013.1.13AR.2. When formatted with ext4 I get good write speeds with about 140MB/s. How can I fix the writespeed?

  Read the article

• Servers at remote sites vs. centralized servers?

  - by Boden

  Looking for some opinions here. We've got three physical locations and site-to-site VPN between all three. Currently we've got Windows domain controllers at each location, with roughly 50 clients at each. The domains are currently separate, and we're looking at integrating the three sites. Email (Exchange) will be located at the primary site, and RPD is already being used at the secondary branches to hit the app servers also located at the primary site. The bulk of the local user load at the other two sites is just file sharing. What would the main benefits and drawbacks be of replacing the local domain controllers with NAS devices, and only keeping the domain controller(s) at the primary site? (assuming upgrades are coming regardless) Under what circumstances would you choose one setup over the other?

  Read the article

• apache and ajp performance

  - by user12145

  I have an apache sitting in front of two tomcat app servers(one on the same physical server, the other on a different one) that does time consuming work(0.5 sec to 10sec per request). The apache http server is getting killed by an average of 1 to 2 concurrent requests per second. both Server spec is about 2GB of RAM. Is there a way to optimize apache to handle the load? any advise is welcome. BalancerMember ajp://localhost:8009/xxxxxx BalancerMember ajp://XXX.XX.XXX.XX:8009/xxxxxx I keep getting the following in apache2.2 log: [Mon Dec 28 00:31:02 2009] [error] ajp_read_header: ajp_ilink_receive failed [Mon Dec 28 00:31:02 2009] [error] (120006)APR does not understand this error code: proxy: read response failed from 127.0.0.1:8009 (localhost)

  Read the article

• Windows Vista - Can't start any program without choosing "Run as administrator"

  - by Dave Forgac

  A friend called me saying that her computer recently said it was applying a Windows update when it was shutting down. Now when logged in as her normal user whenever she tries to run any program from the start menu or from a shortcut on the desktop she gets the following popup: "Windows cannot access the specified device path or file You may not have the appropriate permissions to access the item" If she right-clicks and chooses 'Run as administrator' the program will run. We checked the Windows update history and it said the update was applied successfully and that there are no updates available. Unfortunately I'm in a different city so I don't have physical access to the system to look at it any further. Has anyone had a similar problem or have any suggestions?

  Read the article

• Intel SASWT4I SAS/SATA Controller Question

  - by Joe Hopfgartner

  Hey there! I want to assemble a cheap storage sytem based on the Norco RPC-4020 Case. When searching for controllers I found this one: Intel® RAID Controller SASWT4I This is a quote form the Spec Sheet: Scalability. Supports up to 122 physical devices in SAS mode which is ideal for employing JBODs (Just a Bunch Of Disks) or up to 14 devices in RAID 0, 1, 1E/10E mode through direct connect device attachment or through expander backplane support. Does that mean I can attatch 14 SATA drives directly to the controller using SFF-8087 - 4x SATA breakout cables? That would be nice because then I can choose a mainboard that has 6 Onboard SATA and i can connect all 20 bays while only spending 155$ on the controller and like another 100$ on cables. Would that work? And why is it 14 and not 16 when there are 4 Ports? I am really confused about all the breakout/fanout/(edge-)expanding/multiplying/channel stuff...

  Read the article

• Flow of packets in network

  - by user58859

  I can't visualize in my mind the network traffic flow. eg. If there are 15 pc's in a LAN When packet goes from router to local LAN, do it passes all the computers? Does it go to the ethernet card of every computer and those computers accept the packet based on their physical address? To which pc the packet will go first? To the nearest to the router? What happens if that first pc captures that packet(though it is not for it)? What happens when a pc broadcast a message? Do it have to generate 14 packets for all the pc's or only one packet reach to all pc's? If it is one packet and captured by first pc, how other pc's can get that? I can't imagine how this traffic is exactly flows? May be my analogy is completely wrong. Can anybody explain me this?

  Read the article

• VMware virtual network adapters and Windows Firewall

  - by anonymous

  I am running VMware Workstation 7.1.4 on Windows 7 Enterprise SP1-U (x64). Aside from the physical network adapter, I have created a single virtual network adapter (VMware Virtual Ethernet Adapter for VMnet1) which is connected to (can be seen by) the host and the guests. My problem is, even after applying the "*NdisDeviceType = 1" tweak to the virtual adapter, making it disappear from the Network and Sharing Center, I still can't connect to programs running in the host from the guests, unless I specifically "allowed the program to communicate with the public network" using the Windows Firewall (which I don't want to do). This happens to all the programs and services running in the host (File and Printer Sharing, Database server, HTTP proxy, etc.) I am getting the impression that applying the "*NdisDeviceType = 1" tweak only hides a network from the Network and Sharing Center but not actually making it private. Any hints and suggestions?

  Read the article

• Simple NAT router for ESX

  - by Evan M.

  Hi Guys, I'm looking for a simple virtual appliance that I can deploy to my ESX environment to use as a virtual NAT router / firewall to create an isolated network that I can easily give internet access too. Basic setup: ESX Host, has 2 vswitches configured: 1 is connected to the physical LAN, the other is isolated. I need an appliance that I can add 2 vNICs to, and attach one to the isolated vSwitch, the other to the LAN, to give the isolated network outbound access (so it can reach the internet). Anyone have an appliance that I can setup quickly to do so? Thanks.

  Read the article

< Previous Page | 72 73 74 75 76 77 78 79 80 81 82 83  | Next Page >