Search Results

Search found 24935 results on 998 pages for 'test utilities'.

Page 791/998 | < Previous Page | 787 788 789 790 791 792 793 794 795 796 797 798  | Next Page >

• How to host an ssh server?

  - by balki

  Hi, I have a broadband internet connection. I have an wireless modem (Airtel India). I don't have a static ip address. I want to host a ssh/web/ftp server to be visible to the outside world just for testing and learning purpose so I can ask my friend to connect to my current ip address and test. My modem has an admin interface which allows to port forward and open ports. I set up ssh server as shown and checked if port 22 is open using this website , Port Scan And port 22 is open. I have an openssh server running and it works if i do, ssh [email protected] which is my local ip address but doesn't work if i do ssh [email protected] where 122.xx.xx.xx is my external ip address of my modem which i checked from whatismyipaddress.com. Since it looks like the port is open, I wonder if there is some setting I need to change in my server config to expose my server. How should I go about solving this?

  Read the article

• Short, intermittent USB port timeouts

  - by jacobsee

  I have a data acquisition application controlled by a Windows PC. I am using an Intel Desktop Board DH67CL motherboard. This has 6 USB2 ports along with 2 of the new blue USB3 ports. The DAQ instrument connects via USB to the computer. Roughly once every day or two there is a short communication glitch with the USB that causes the instrument to disconnect briefly and then reconnect. This is logged so I know whenever it happens. Occasionally it will cause the data acquisition to stop. I've verified that the glitches will go away if I use the USB3 ports, or if I use a PCI add-on card with USB ports. So it seems that there is something going on with these built-in USB2 ports on this motherboard. I haven't yet had a chance to test with other motherboards. My question: what could be causing these glitches and how to get rid of them for this board, or is there a better motherboard to use? We have standardized on the DH67CL because it's inexpensive, has 3 PCI slots that we need, and is readily available. We don't need the power of higher-end server boards but reliability is important. Thanks. Update: This problem has been reproduced many times on different hardware, though we always use the same model of motherboard (DH67CL) and power supply (Antec EA-430D). I don't think the power requirements are very high but will check on that.

  Read the article

• Nginx flv audio pseudo stream works but video is not loading

  - by sarah

  I am working on a development server for a company & they want nginx webserver to work with. So the requirements for their company is, it should be capable of doing following things i.e hotlink protection, mp4 & flv pseudo stream & secure streaming. However nginx fulfills their requirements and i am configuring their server from past 2 days as i am new to this field so i've only acheived hotlinking prevention in past 2 days. But the problem on which i am stuck is flv pseudo streaming, to make work to mp4 pseudo stream it was just a piece of paper but i am really fuc*ed up with flv pseudo stream. I have converted my flv videos with flvmdi tools to insert many keyframes but the problem is , when i try to seek video from following keyframes that are generated by flvmdi i.e test.flv?start=2681223, video does not load but audio pseudo works fine. So it means no problem with my flv configuration in nginx.conf file. And the forum that i used to compile my nginx-1.2.1 is http://h264.code-shop.com/trac/wiki/Mod-H264-Streaming-Nginx-Version2 & by adding additional module --with-http_flv_module. This forum is really active, hopes i will resolve my problem as soon as you guys will provide me some guide.

  Read the article

• Apache: Isn't chmod 755 enough to set up symlink or alias on Apache httpd on Mac OS 10.5?

  - by eed3si9n

  On my Mac OS 10.5 machine, I would like to set up a subfolder of ~/Documents like ~/Documents/foo/html to be http://localhost/foo. The first thing I thought of doing is using Alias as follows: Alias /foo /Users/someone/Documents/foo/html <Directory "/Users/someone/Documents/foo/html"> Options Indexes FollowSymLinks MultiViews Order allow,deny Allow from all </Directory> This got me 403 Forbidden. In the error_log I got: [error] [client ::1] (13)Permission denied: access to /foo denied The subfolder in question has chmod 755 access. I've tried specifying likes like http://localhost/foo/test.php, but that didn't work either. Next, I tried the symlink route. Went into /Library/WebServer/Documents and made a symlink to ~/Documents/foo/html. The document root has Options Indexes FollowSymLinks MultiViews This still got me 403 Forbidden: Symbolic link not allowed or link target not accessible: /Library/WebServer/Documents/foo What else do I need to set this up? Solution: $ chmod 755 ~/Documents In general, the folder to be shared and all of its ancestor folder needs to be viewable by the www service user.

  Read the article

• Exceptional slowdown of robocopy copying from VM to DFS array

  - by user1588867

  I've got an old win 2003 VM (VMware) on a blade cluster of VMs that I'm moving a considerable amount of files to our new DFS array. There are two main folders with about 1.7 million and half a million smaller files (letters, memos, and other smaller files) respectively. Total size is ~420 GB and ~100 GB. We're using the gui version of robocopy on the server to copy the files. We had initiated a file copy about a month ago to test the process and found that it was taking around 4 hours for the large file. Now that I'm in the process of actually switching the files over it has been taking 18-20 hours. Nothing has changed on the server side and nothing has changed on the settings of the copy (no logs, 1 retry with a wait of 1 second). Our intent is to shut off the share and force the copy over again to get all the files that have been left out of the copy due to being locked by users. I can't take a 20 hour outage to do that though. Does anyone have any theories about what could be causing such a delay for robocopy compared to previously shorter runs?

  Read the article

• How can I create a VLAN on my extreme switch for a separate subnet/domain?

  - by drpcken

  I'm putting together a small active directory implementation for a buddy of mine. I currently have 2 servers (one is the primary domain controller) and a couple clients. I need to test and run updates on every machine on this domain, but I would have plug them into my current LIVE domain to get it internet access. From what I've read having two separate domains on a single subnet is a bad idea (even though it is temporary) so I don't want to risk messing anything up on my production domain. I'm pretty sure I can create a separate VLAN on my extreme 48 port switch and plug this smaller domain into it on a different subnet, but I don't know the commands. Both subnets would need internet access of course (one of the things I can't wrap my head around is routing internet traffic between subnets (gateway is on production subnet). Switch is a Summit x450e-48p My production domain is on subnet 192.168.200.0. My new domain I want to put online would go into subnet 192.168.10.0. A shove in the right direction would be greatly appreciated. Thank you!

  Read the article

• How to verify TRIM/discard on encrypted swap?

  - by svarni

  I am using an encrypted swap partition via ecryptfs-setup-swap on my Ubuntu 13.04 computer using a SSD. I have manually set up trim for my ext4 root partition (simply by adding the "discard" option in /etc/fstab). I also manually ran fstrim on the root partition prior to booting and using dstat I saw that for a few seconds several GB/s of data have been written to the disk. That was presumably the effect of the trim command. These high writerates are reproducable by deleting huge files and have not occured before setting up trim, so I take them as evidence for working trim/discard. Manually enabling trim on my root partition has stopped the wearout of my precious new disk from 365 used reserved blocks (out of 6176 total) within three months down to 0 additional used reserved blocks within three additional months (data from SMART attributes). Because I want to minimize the wearout of my SSD I now would like to know whether my swap partition (which is encrypted using ecryptfs-setup-swap) also makes use of the trim/discard option. I tried sudo swapon -d -v /dev/mapper/cryptswap1 but did not receive particular information ("-v") about whether trim/discard ("-d") was applied. If unsupported, i would expect a message. Then I tried sudo dd if=/dev/sda6 count=1 BS=1M | xxd | less directly after booting and when no swapspace was used but I saw not only zeroes. I assume, when looking at freshly trimmed regions, the disk would send zeroes instead of reading random sectors (and according to some forums, (unencrypted) swap space is trimmed once upon boot). Long story short: Are there any ideas on how to test if trim is effectively used for my encrypted swap? And if not, any ideas on how to - at least manually, for once - trim the whole swap space? I wouldn't want to tinker with the partition itself, because I dont know if it needs to be reinitialized as (encrypted) swap - I dont want to be left with an unbootable system :)

  Read the article

• Hide/Replace Nginx Location Header?

  - by Steven Ou

  I am trying to pass a PCI compliance test, and I'm getting a single "high risk vulnerability". The problem is described as: Information on the machine which a web server is located is sometimes included in the header of a web page. Under certain circumstances that information may include local information from behind a firewall or proxy server such as the local IP address. It looks like Nginx is responding with: Service: https Received: HTTP/1.1 302 Found Cache-Control: no-cache Content-Type: text/html; charset=utf-8 Location: http://ip-10-194-73-254/ Server: nginx/1.0.4 + Phusion Passenger 3.0.7 (mod_rails/mod_rack) Status: 302 X-Powered-By: Phusion Passenger (mod_rails/mod_rack) 3.0.7 X-Runtime: 0 Content-Length: 90 Connection: Close <html><body>You are being <a href="http://ip-10-194-73-254/">redirect ed</a>.</body></html> I'm no expert, so please correct me if I'm wrong: but from what I gathered, I think the problem is that the Location header is returning http://ip-10-194-73-254/, which is a private address, when it should be returning our domain name (which is ravn.com). So, I'm guessing I need to either hide or replace the Location header somehow? I'm a programmer and not a server admin so I have no idea what to do... Any help would be greatly appreciated! Also, might I add that we're running more than 1 server, so the configuration would need to be transferable to any server with any private address.

  Read the article

• How to access XAMPP virtual hosts from iPad on local network?

  - by martin's

  Using XAMPP on one machine. Multiple virtual hosts defined. One per project. Format is .local For example: apple.local microsoft.local client-site.local our-own-internal-site.local All works perfectly from that one machine. I now want to have other systems within the network access the various sites. The main reason for wanting to do this is to be able to test site functionality and layout from mobile devices without having to upload partial work to public servers. I can access the main XAMPP default site by simply entering the IP address of the XAMPP machine in, say, Safari on an iPad. However, there is no way to reach .local that I can see. Would this entail setting up a DNS server within the network? We have a mixture of Windows and Mac machines. No Linux. The XAMPP machine is Vista 64. I don't want real external internet access to be affected in any way, just ".local" pointed to the XAMPP machine if that makes sense.

  Read the article

• Nginx Ubuntu Postfix Config - Can't connect to incoming IMAP server 'server not responding' but can send mail via outgoing using same details?

  - by daveaspinall

  I'm pretty to new server admin and especially nginx but seem to be getting ok fine apart from accessing my mail via my iPhone? I've changed my domain to 'domain.com' The thing is I can send mail via my outgoing IMAP server but can't connect to the incoming one? I just get the message "the mail server at mail.domain.com is not responding" /etc/postfix/main.cf alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no broken_sasl_auth_clients = yes config_directory = /etc/postfix home_mailbox = Maildir/ inet_interfaces = all inet_protocols = all mailbox_command = mailbox_size_limit = 0 mydestination = domain.com, mail.domain.com, localhost.com, , localhost, localhost.localdomain mydomain = domain.com myhostname = mail.domain.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 myorigin = /etc/mailname recipient_delimiter = + relayhost = smtp_tls_note_starttls_offer = yes smtp_tls_security_level = may smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_recipient_restrictions = permit_sasl_authenticated,permit_mynetworks,reject_unauth_destination smtpd_sasl_auth_enable = yes smtpd_sasl_local_domain = smtpd_sasl_security_options = noanonymous smtpd_tls_CAfile = /etc/ssl/certs/cacert.pem smtpd_tls_auth_only = no smtpd_tls_cert_file = /etc/ssl/certs/smtpd.crt smtpd_tls_key_file = /etc/ssl/private/smtpd.key smtpd_tls_loglevel = 1 smtpd_tls_received_header = yes smtpd_tls_security_level = may smtpd_tls_session_cache_timeout = 3600s tls_random_source = dev:/dev/urandom telnet localhost 25 ehlo locahost 250-mail.domain.com 250-PIPELINING 250-SIZE 10240000 250-VRFY 250-ETRN 250-STARTTLS 250-AUTH LOGIN PLAIN 250-AUTH=LOGIN PLAIN 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN Using the following details to connect: username password hostname: mail.domain.com port: 25 iptables --list Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination I also sent mail to the server as a test and got this missage if it helps? Technical details of temporary failure: [mail.domain.com. (10): Connection refused] I also looked in /var/log/mail.log and it has multiple entries of: postfix/smtpd[12239]: connect from 5acefc9a.bb.sky.com[90.206.252.xxx] Mar 23 06:47:09 new-domain postfix/smtpd[12239]: lost connection after CONNECT from 5acefc9a.bb.sky.com[90.206.252.154] Notice new-domain which is incorrect but the server hostname and hostname in the configs are correct? I recently moves servers and the host has set the primary domain on the service as new-domain.com so this may be the issue? Like I said, it works to connect to outgoing server, but incoming gets the not responding error? Any idea would be much appreciated!

  Read the article

• a brand new FS based on a database without using fuse

  - by Devrim

  hi all, To serve millions of files out of a single directory, being able to connect to a drive from hundreds of endpoints, and for some other reasons (to avoid gluster/nfs/all fs based networking solutions), I want to evaluate the possibility of making a filesystem that's based on a mongodb (or any other). Basically, it works like fusefs, every single file is kept in mongo gridfs. In theory, I do, mount mongodbfs /mountPoint mongodb://localhost then when i say touch /mountPoint/test.txt this file is inserted into mongodb. This FS will also store uid/gid and perms with the file, we can throw hundreds of servers to it, and no useradd will be necessary. I'm not thinking to include all the features of FS, just the ones we need. My question is, how do I start my quest in finding resources, books, links, people, developers who'd help me implement this? at least a proof of concept. Is it feasible? What should I expect as a timeline for such undertaking? Please only think about gazillion small files and folders.

  Read the article

• No sound Ubuntu 10.10 (have SB Live! card)

  - by Chris Frazier

  I am new to Linux/Ubuntu and I just installed 10.10 on my Dell Desktop PC that was running Windows XP. The PC is about 5-6 years old and the sound card it has is a SoundBlaster Live! card. The Sound Preferences recognizes the card as [SB Live! Value] EMU10k1X. It is currently set to Analog Stereo Duplex. I tried multiple other sound configurations and nothing works. No sound but some clicks come out of the speakers. I ran the system test and during the audio tests the same thing happened, just clicks and pops. I tried to play some music with Rhythmbox and when it tries to play a track it tries for several seconds and then just closes itself, or sometimes just doesn't play. I ran a check for drivers, but the only driver it found to install was for my nVidia video card. It did not show any drivers for the sound card. Does anyone have any idea what I need to do to get the sound to work?

  Read the article

• xcopy Not Surpressing File/Directory Query

  - by Daniel Bingham

  Hey folks, I'm attempting to use xcopy to copy over a file from one machine to another on our network as part of a Java program. I'm calling xcopy like this: xcopy "C:\Program Files\path\to\my\file" "\\othermachine\c$\Documents and Settings\<myUserName>\Desktop\Test\path\in\directory\structure\to\file" /e /y /i Because I'm calling it from with in Java, I need all the prompts to be suppressed. For the most part, \i and \y have done exactly that. However, for this one file /i fails and I get the file or directory prompt. The result is that it hangs the entire program. I've also tried calling it with /s /t /q appended on to the existing options, to no avail. Why isn't /i working to suppress the File or Directory prompt? Is there an order I need to call the options in? Is there something else I need to do? EDIT: I should mention, the file is a text file - single line of text. It does not have an extension. It looks like this: FILE-NAME

  Read the article

• Slow connection to Linux MySQL from Windows only (XAMPP)

  - by Josh

  I'm having a problem with a PHP project (using Kohana 3.2 framework) on my Windows 7 64-bit machine connecting to the database. The development database is stored on a Ubuntu Linux server on the local network. Other development machines running OSX and Linux are connecting fine. There are no other Windows development machines to test with. I can access MySQL fine using MySQL Workbench, and other projects (which I believe to be less database heavy) run mostly ok, only occasionally getting timeout messages. I'm constantly getting Maximum execution time of 30 seconds exceeded when functions such as mysql_query() are run in this particular project. Specifically, the Kohana file where the timeout occurs is MODPATH\database\classes\kohana\database\mysql.php [ 186 ]. My local set-up is: Windows 7 Professional 64bit XAMPP 1.7.7 (PHP 5.3.8) The output of uname -a of the Linux server is: Linux peach 2.6.38-11-server #50-Ubuntu SMP Mon Sep 12 21:34:27 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux I've tried the following, with no success: Disabling Windows firewall Switching between using a persistant and normal connection In my.cnf, adding skip-name-resolve Increasing wait_timeout Enabling bind-address I've run out of ideas now, and have no idea how to debug an odd issue like this. Has anyone come across this before, or have any idea how I could find the root of the issue, or what might be the problem?

  Read the article

• ldap-authentication without sambaSamAccount on linux smb/cifs server (e.g. samba)

  - by umlaeute

  i'm currently running samba-3.5.6 on a debian/wheezy host to act as the fileserver for our department's w32-clients. authentication is done via OpenLDAP, where each user-dn has an objectclass:sambaSamAccount that holds the smb-credentials and an objectclass:shadowAccount/posixAccount for "ordinary" authentication (e.g. pam, apache,...) now we would like to dump our department's user-db, and instead use authenticate against the user-db of our upstream-organisation. these user-accounts are managed in a novell-edirectory, which i can already use to authenticate using pam (e.g. for ssh-logins; on another host). our upstream organisation provides smb/cifs based access (via some novell service) to some directories, which i can access from my linux client via smbclient. what i currently don't manage to do is to use the upstream-ldap (the eDirectory) to authenticate our institution's samba: i configured my samba-server to auth against the upstream ldap server: passdb backend = ldapsam:ldaps://ldap.example.com but when i try to authenticate a user, i get: $ smbclient -U USER \\\\SMBSERVER\\test Enter USER's password: Domain=[WORKGROUP] OS=[Unix] Server=[Samba 3.6.6] tree connect failed: NT_STATUS_ACCESS_DENIED the logfiles show: [2012/10/02 09:53:47.692987, 0] passdb/secrets.c:350(fetch_ldap_pw) fetch_ldap_pw: neither ldap secret retrieved! [2012/10/02 09:53:47.693131, 0] lib/smbldap.c:1180(smbldap_connect_system) ldap_connect_system: Failed to retrieve password from secrets.tdb i see two problems i'm having: i don't have any administrator password for the upstream ldap (and most likely, they won't give me one). i only want to authenticate my users, write-access is not needed at all. can i go away with that? the upstream ldap does not have any samba-related attributes in the db. i was under the impression, that for samba to authenticate, those attributes are required, as smb/cifs uses some trivial hashing which is not compatible with the usual posixAccount hashes. is there a way for my department's samba server to authenticate against such an ldap server?

  Read the article

• RAID 10 or RAID 5 for multiple VMs - what is the best choice?

  - by Lars Fastrup

  I have just ordered a new rig for my business. We do a lot of software development for Microsoft SharePoint and need the rig to run several virtual machines for development and test purposes. We will be using the free VMware ESXi for virtualization. For a start, we plan to build and start the following VMs - all with Windows Server 2008 R2 x64: Active Directory server MS SQL Server 2008 R2 Automated Build Server SharePoint 2010 Server for hosting our public Web site and our internal Intranet for a few people. The load on this server is going to be quite insignificant. 2xSharePoint 2007 development server 2xSharePoint 2010 development server Beyond that we will need to build several SharePoint farms for testing purposes. These VMs will only be started when needed. The specs of the new rig is: Dell R610 rack server 2xIntel XEON E5620 48GB RAM 6x146GB SAS drives Dell H700 RAID controller We believe the new server is going to make our VMs perform a lot better than our existing setup (2xIntel XEON, 16GB RAM, 2x500 GB SATA in RAID 1). But we are not sure about the RAID level for the new rig. Should we go for having the the 6x146GB SAS drives in a RAID 10 configuration or a RAID 5 configuration? RAID 10 seems to offer better write performance and lower risk of a RAID failure. But it comes at a cost of less drive space. Do we need RAID 10 or would RAID 5 also be a good choice for us?

  Read the article

• Measuring performance indicators on a cluster

  - by Aditya Singh

  My architecture is based on Amazon. A ELB load balancer balances POST requests among m1.large instances. Every instance has a nginx server on port 80 which distributes the requests to 4 python-tornado servers on backend which handle the request. These tornado servers are taking about 5 - 10ms to respond to one request but this is the internal compute time of every request. I want to put this thing on test and i want to measure the response time from ELB to upstream and back and how does it vary when the QPS throughput is increased and plot a graph of Time vs. QPS vs. Latency and other factors like CPU and Memory. Is there a software to do that or should i log everything somewhere with latency checks and then analyze the whole log to get the stuff out. I would also need to write a self-monitor which keeps checking the whole response time. Is it possible to do it with a script from within the server. If so, will it be accurate ?

  Read the article

• W7-pro indexing mydoc on disk partition does not work

  - by Yvan Thery

  I am working on a HP-7100 mini tower running W7 Pro 64bits. My Local HD includes C:/ + 2 disk partitions : all my documents are located on disk partition L:/ and all my media files are on disk partition M:/ The indexing process works well on C:/ and M:/ but does not index the L:/ any more also all of them are allowed to be indexed, also the system is present on all drive security tabs. I have tested to rebuilt the indexing file with a new setting including few directories present on drive C/M/L but still with L: does not work ! One more thing I can tell you is that even after rebuilding the indexing file, I can find some residual directories or files which are out of the test selection. It is like unerased components remaining in the indexing database. As I do not know precisely how the indexing process works it is hard to know what to do ... Recently I had a bad time after using a past restoration procedure ... maybe it did corrupt the indexing file ???? If I start indexing the all L:/ disk partition the system stop at 39 found index also many more are existing .... Does any one from you guys could advise the process to create a new indexing database ... ? Any idea to get out of this mess ? Many thanks for assistance Yvan

  Read the article

• What user information is exposed via a browser?

  - by ipso

  Is there a function or website that can collect and display ALL of the user information that can be obtained via a browser? Background: This of course does not account for the significant cross-reference abilities of large corporations to collate multiple sources and signals from users across various properties, but it's a first step. Ghostery is just a great idea; to show people all of the surreptitious scripts that run on any given website. But what information is available – what is the total set of values stored – that those scripts can collect from? If you login to a search engine and stay logged in but leave their tab, is that company still collecting your webpage viewing and activity from other tabs? Can past or future inputs to pages be captured – say comments on another website? What types of activities are stored as variables in the browser app that can be collected? This is surely a highly complex question, given to countless user scenarios – but my whole point is to be able to cut through all that – and just show the total set of data available at any given point in time. Then you can A/B test and see what is available with in a fresh session with one tab open vs. the same webpage but with 12 tabs open, and a full day of history to boot. (Latest Firefox & Chrome – on Win7, Win8 or Mint13 – although I'd like to think that won't make too much of a difference. Make assumptions. Simple is better.)

  Read the article

• Why am I not able to create a backup plan for TFS?

  - by noocyte

  I am trying to create a backup plan using the TFS Power Tools but I keep running into this error message: I have checked that the account has Full Control on the share, I can edit, create and delete files there. From the log: [Info @07:15:00.403] Starting creating backup test validation [Error @07:15:00.700] Microsoft.SqlServer.Management.Smo.FailedOperationException: Backup failed for Server 'WMSI003714N\SqlExpress'. ---> Microsoft.SqlServer.Management.Common.ExecutionFailureException: An exception occurred while executing a Transact-SQL statement or batch. ---> System.Data.SqlClient.SqlException: Cannot open backup device '\\wmsi003714n\sql dump\Tfs_Configuration_20100910091500.bak'. Operating system error 5(failed to retrieve text for this error. Reason: 1815). BACKUP DATABASE is terminating abnormally. at Microsoft.SqlServer.Management.Common.ConnectionManager.ExecuteTSql(ExecuteTSqlAction action, Object execObject, DataSet fillDataSet, Boolean catchException) at Microsoft.SqlServer.Management.Common.ServerConnection.ExecuteNonQuery(String sqlCommand, ExecutionTypes executionType) --- End of inner exception stack trace --- at Microsoft.SqlServer.Management.Common.ServerConnection.ExecuteNonQuery(String sqlCommand, ExecutionTypes executionType) at Microsoft.SqlServer.Management.Common.ServerConnection.ExecuteNonQuery(StringCollection sqlCommands, ExecutionTypes executionType) at Microsoft.SqlServer.Management.Smo.ExecutionManager.ExecuteNonQuery(StringCollection queries) at Microsoft.SqlServer.Management.Smo.BackupRestoreBase.ExecuteSql(Server server, StringCollection queries) at Microsoft.SqlServer.Management.Smo.Backup.SqlBackup(Server srv) --- End of inner exception stack trace --- at Microsoft.SqlServer.Management.Smo.Backup.SqlBackup(Server srv) at Microsoft.TeamFoundation.PowerTools.Admin.Helpers.BackupFactory.TestBackupCreation(String path) [Error @07:15:00.731] !Verify Error!: Account GROUPINFRA\SA-NO-TeamService failed to create backups using path \\wmsi003714n\sql dump [Info @07:15:00.731] "Verify: Grant Backup Plan Permissions\Root\VerifyDummyBackupCreation(VerifyTestBackupCreatedSuccessfully): Exiting Verification with state Completed and result Error" Any ideas?

  Read the article

• unicorn and nginx, went wrong

  - by achempion

  I try to deploy my app via capistrano. It was done, but when I start to nginx and show my site in the browser I see 'We're sorry, but something went wrong.' It is bad. I use unicorn. See my configs https://gist.github.com/3904032 I try to start server via rails s -e prodiction and it's work! I think that this error may be because I can't restart server root@li272-194:~# /etc/init.d/nginx restart Restarting nginx: the configuration file /etc/nginx/nginx.conf syntax is ok configuration file /etc/nginx/nginx.conf test is successful [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: still could not bind() nginx. any ideas? nginx log 2012/10/17 02:57:41 [error] 3271#0: *1 could not find named location "@myapp", client: 91.192.62.77, server: 178.79.153.194, request: "GET / HTTP/1.1", host: "178.79.153.194" 2012/10/17 02:19:08 [crit] 2448#0: *8 connect() to unix:/srv/zarcon/shared/unicorn.sock failed (2: No such file or directory) while connecting to upstream, client: 91.192.62.77, server: zarkon, request: "GET / HTTP/1.1", upstream: "http://unix:/srv/zarcon/shared/unicorn.sock:/", host: "178.79.153.194"

  Read the article

• How to I configure open_basedir parameter under my Centos VPS?

  - by deltanovember

  The parameter can be seen here http://wordswithfriends.net/test.php open_basedir /var/www/vhosts/wor.wordswithfriends.net/wordswithfriends.net/:/tmp I'm trying to add PHP pear directories /var/www/vhosts/wor.wordswithfriends.net/conf is as follows -rw-r----- 1 root apache 6461 Jan 25 08:56 12959674170.16899500_httpd.include -rw-r----- 1 root apache 6461 Jan 31 06:52 12960111810.31860800_httpd.include -rw-r----- 1 root apache 6532 Jan 31 06:55 12964785250.54523600_httpd.include -rw-r----- 1 root apache 6532 Jan 31 07:01 12964788880.47252600_httpd.include -rw-r----- 1 root apache 6532 Jan 31 15:54 12965108850.92819600_httpd.include -rw-r----- 1 root apache 6652 Jan 31 21:32 12965206700.32285200_httpd.include Currently configured as follows grep base 12965206700.32285200_httpd.include php_admin_value open_basedir /var/www/vhosts/wor.wordswithfriends.net/httpdocs/:/tmp/:/usr/share/pear/:/local/PEAR/ php_admin_value open_basedir /var/www/vhosts/wor.wordswithfriends.net/httpdocs/:/tmp/:/usr/share/pear/:/local/PEAR/ php_admin_value open_basedir /var/www/vhosts/wor.wordswithfriends.net/httpdocs/:/tmp/:/usr/share/pear/:/local/PEAR/ php_admin_value open_basedir /var/www/vhosts/wor.wordswithfriends.net/httpdocs/:/tmp/:/usr/share/pear/:/local/PEAR/ Configured vhost.conf as follows <Directory /var/www/vhosts/wor.wordswithfriends.net/wordswithfriends.net> <IfModule sapi_apache2.c> php_admin_flag engine on php_admin_flag safe_mode off php_admin_value open_basedir "/var/www/vhosts/wor.wordswithfriends.net:/tmp:/usr/share/pear/local/PEAR" </IfModule> <IfModule mod_php5.c> php_admin_flag engine on php_admin_flag safe_mode off php_admin_value open_basedir "/var/www/vhosts/wor.wordswithfriends.net:/tmp:/usr/share/pear:/local/PEAR" </IfModule> </Directory> Restarted apache and the parameter is still the same. I'm not sure why my pear directories are not showing up. I'm using Plesk. Any help appreciated

  Read the article

• Safe use of Update-FormatData?

  - by Steve B

  In a custom PowerShell module, I have at the top of my module definition this code: Update-FormatData -AppendPath (Join-Path $psscriptroot "*.ps1xml") This is working fine as all .ps1xml files are loaded. However, the module is sometimes loaded using Import-Module MyModule -Force (actually, this is in the install script of the module). In this case, the call to Update-FormatData fails with this error : Update-FormatData : There were errors in loading the format data file: Microsoft.PowerShell, c:\pathto\myfile.Types.ext.ps1xml : File skipped because it was already present from "Microsoft.PowerShell". At line:1 char:18 + Update-FormatData <<<< -AppendPath "c:\pathto\myfile.Types.ext.ps1xml" + CategoryInfo : InvalidOperation: (:) [Update-FormatData], RuntimeException + FullyQualifiedErrorId : FormatXmlUpateException,Microsoft.PowerShell.Commands.UpdateFormatDataCommand Is there a way to safely call this command? I know I can call Update-FormatData with no parameters, and it will update any known .ps1xml file, but this would work only if the file has already been loaded. Can I list somewhere the loaded format data files? Here is a bit of background: I'm building a custom module that is installed using a script. The install script looks like : [CmdletBinding(SupportsShouldProcess=$true,ConfirmImpact="High")] param() process { $target = Join-Path $PSHOME "Modules\MyModule" if ($pscmdlet.ShouldProcess("$target","Deploying MyModule module")) { if(!(Test-Path $target)) { new-Item -ItemType Directory -Path $target | Out-Null } get-ChildItem -Path (Split-Path ((Get-Variable MyInvocation -Scope 0).Value).MyCommand.Path) | copy-Item -Destination $target -Force Write-Host -ForegroundColorWhite @" The module has been installed. You can import it using : Import-Module MyModule Or you can add it in your profile ($profile) "@ Write-Warning "To refresh any open PowerShell session, you should run ""Import-Module MyModule -Force"" to reload the module" Import-Module MyModule -Force Write-Warning "This session has been refreshed." } } MyModule defines, as first statement, this line : Update-FormatData -AppendPath (Join-Path $psscriptroot "*.ps1xml") As I updated my $profile to always load this module, the Update-Path command has been called when I run the install script. In the install script, I force import the module, which be fire again the module, and then, the Update-Path call

  Read the article

• Cannot send email to info@ or support@

  - by user3022598

  I am trying to send email from my gmail account to a couple user accounts I have on my new Centos server. The email is setup correctly and I can send receive from accounts ok except info and support. I tried to setup two users "info" and "support" I have a php form that sends out email that works fine for all users except info and support. To test this and make sure that something did not change from yesterday i just created a new user "frank" and tried the submit form and it worked fine. From my gmail account i can email "frank" however i cannot email "info" or "support" The logs I pulled are as follows and i think i see the issue but no idea how to fix it. Aug 15 12:20:55 mail postfix/qmgr[1568]: 1815C20A83: from=, size=1815, nrcpt=1 (queue active) Aug 15 12:20:55 mail postfix/local[2270]: 1815C20A83: to=, relay=local, delay=0.28, delays=0.26/0.01/0/0.01, dsn=2.0.0, status=sent (delivered to maildir) Aug 15 12:17:13 mail postfix/qmgr[1568]: 3C18520A7F: from=, size=1818, nrcpt=1 (queue active) Aug 15 12:17:13 mail postfix/local[2201]: 3C18520A7F: to=, orig_to=, relay=local, delay=0.28, delays=0.25/0.01/0/0.01, dsn=2.0.0, status=sent (delivered to maildir) Aug 15 12:15:24 mail postfix/qmgr[1568]: 2F79420A79: from=, size=1813, nrcpt=1 (queue active) Aug 15 12:15:24 mail postfix/local[2155]: 2F79420A79: to=, orig_to=, relay=local, delay=0.29, delays=0.27/0.01/0/0.01, dsn=2.0.0, status=sent (delivered to maildir) For some reason frank goes out fine, however support and info go to root? Why?

  Read the article

• less maximum buffer size?

  - by Tyzoid

  I was messing around with my system and found a novel way to use up memory, but it seems that the less command only holds a limited amount of data before stopping/killing the command. To test, run (careful! uses lots of system memory very fast!) $ cat /dev/zero | less From my testing, it looks like the command is killed after less reaches 2.5 gigabytes of memory, but I can't find anything in the man page that suggests that it would limit it in such a way. In addition, I couldn't find any documentation via the google on the subject. Any light to this quite surprising discovery would be great! System Information: Quad core intel i7, 8gb ram. $ uname -a Linux Tyler-Work 3.13.0-32-generic #57-Ubuntu SMP Tue Jul 15 03:51:08 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux $ less --version less 458 (GNU regular expressions) Copyright (C) 1984-2012 Mark Nudelman less comes with NO WARRANTY, to the extent permitted by law. For information about the terms of redistribution, see the file named README in the less distribution. Homepage: http://www.greenwoodsoftware.com/less $ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 14.04 LTS Release: 14.04 Codename: trusty

  Read the article

< Previous Page | 787 788 789 790 791 792 793 794 795 796 797 798  | Next Page >