Search Results

Search found 24935 results on 998 pages for 'test utilities'.

Page 795/998 | < Previous Page | 791 792 793 794 795 796 797 798 799 800 801 802  | Next Page >

• S.M.A.R.T. broken sectors

  - by Jeffrey Vandenborne

  Recently I received my hard drive (LaCie) that I've sent away for warranty, my disk failed, and I used Palimpsest Disk utility to check if anything was wrong in the S.M.A.R.T Status. And it said that there were a few broken sectors. So the next day, I went to the store and told the story. 4 weeks later I actually got my drive back. The first thing I did was plugging it in and starting the disk utility, and weirdly it showed me pretty much the exact same things, even the values of most tests were the same as they were before when my drive broke. The serial number is different though, but it does show a very peculiar value. Now I'm wondering, I'm almost sure it's the exact same drive and it still says I've got broken sectors, does it just say that because it has been cached in the drive somewhere while LaCie DID actually fix it? Or should I run the extended self test (which seems to take hours) first? Also I've tried the smartctl command tool, it says the drive has smart support, but it doesn't show anything, it says that it's enabled, but then it says that it's disabled, picture below The picture of the Disk utility: Thanks in advance

  Read the article

• Why is my rsync so slow?

  - by iblue

  My Laptop and my workstation are both connected to a Gigabit Switch. Both are running Linux. But when I copy files with rsync, it performs badly. I get about 22 MB/s. Shouldn't I theoretically get about 125 MB/s? What is the limiting factor here? EDIT: I conducted some experiments. Write performance on the laptop The laptop has a xfs filesystem with full disk encryption. It uses aes-cbc-essiv:sha256 cipher mode with 256 bits key length. Disk write performance is 58.8 MB/s. iblue@nerdpol:~$ LANG=C dd if=/dev/zero of=test.img bs=1M count=1024 1073741824 Bytes (1.1 GB) copied, 18.2735 s, 58.8 MB/s Read performance on the workstation The files I copied are on a software RAID-5 over 5 HDDs. On top of the raid is a lvm. The volume itself is encrypted with the same cipher. The workstation has a FX-8150 cpu that has a native AES-NI instruction set which speeds up encryption. Disk read performance is 256 MB/s (cache was cold). iblue@raven:/mnt/bytemachine/imgs$ dd if=backup-1333796266.tar.bz2 of=/dev/null bs=1M 10213172008 bytes (10 GB) copied, 39.8882 s, 256 MB/s Network performance I ran iperf between the two clients. Network performance is 939 Mbit/s iblue@raven $ iperf -c 94.135.XXX ------------------------------------------------------------ Client connecting to 94.135.XXX, TCP port 5001 TCP window size: 23.2 KByte (default) ------------------------------------------------------------ [ 3] local 94.135.XXX port 59385 connected with 94.135.YYY port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.09 GBytes 939 Mbits/sec

  Read the article

• Windows 7 32bit resolution is limited for HDTV monitor

  - by Nick

  I have a small Magnavox HDTV that i am using to test a Frankenstein PC build. The goal is to eventually connect to my old rear projection HDTV which supports 1080i via component input. The goal is also not to buy anymore stuff, otherwise i will just buy a smartTV and be done. I have a ATI Radeon HD 3450 with component out adapter YPrPb. The monitor supports 1080p, but over analog component out, should only go upto 1080i. I have had this working with another setup. On this particular setup, i have Windows 7 32bit, with the latest 12.8 catalyst drivers installed. the windows splash screen starts in 480p, then switches to 480i when the login prompt is shown. When try to change the resolution, 720x480 is the maximum value of the slider. I have also tried the "list all modes" and that also maxes out at 720x480. There are two options for this monitor in the devices seciton, Generic PNP monitor, and Generic non-PNP monitor. Neither setting fixes this. Any ideas on how to get 1080i?

  Read the article

• Samba/Winbind issues joing to Active directory domain

  - by Frap

  I'm currently in the process of setting up winbind/samba and getting a few issues. I can test connectivity with wbinfo fine: [root@buildmirror ~]# wbinfo -u hostname username administrator guest krbtgt username [root@buildmirror ~]# wbinfo -a username%password plaintext password authentication succeeded challenge/response password authentication succeeded however when I do a getent I don't get any AD accounts returned [root@buildmirror ~]# getent passwd root:x:0:0:root:/root:/bin/bash bin:x:1:1:bin:/bin:/sbin/nologin daemon:x:2:2:daemon:/sbin:/sbin/nologin adm:x:3:4:adm:/var/adm:/sbin/nologin lp:x:4:7:lp:/var/spool/lpd:/sbin/nologin sync:x:5:0:sync:/sbin:/bin/sync shutdown:x:6:0:shutdown:/sbin:/sbin/shutdown halt:x:7:0:halt:/sbin:/sbin/halt mail:x:8:12:mail:/var/spool/mail:/sbin/nologin uucp:x:10:14:uucp:/var/spool/uucp:/sbin/nologin operator:x:11:0:operator:/root:/sbin/nologin puppet:x:52:52:Puppet:/var/lib/puppet:/sbin/nologin my nsswitch looks like this: passwd: files winbind shadow: files winbind group: files winbind #hosts: db files nisplus nis dns hosts: files dns and I'm definitely joined to the domain: [root@buildmirror ~]# net ads info LDAP server: 192.168.4.4 LDAP server name: pdc.domain.local Realm: domain.local Bind Path: dc=DOMAIN,dc=LOCAL LDAP port: 389 Server time: Sun, 05 Aug 2012 17:11:27 BST KDC server: 192.168.4.4 Server time offset: -1 So what am I missing?

  Read the article

• What is best configuration settings for Wordpress and MySQL on Win2008 + IIS7 stack?

  - by holiveira

  I currently have four blogs that uses Wordpress running on a shared hosting company. This blogs have a considerable amount of visits and I'm constantly receiving warnings from the hosting company saying that I'm consuming too much server CPU. Considering the fact that I have a dedicated server in another company with plenty of idle resources (it has a quad core Xeon 2.5GHz and 8GB of Ram and run on Win2008) I'm planning to move the blogs to this server in order to have some more freedom. I'm currently using this server to host some web applications using ASP.Net and SQL Express. I've installed a blog to test and it worked fine, but some issues appeared and raised some questions in my mind: How to properly set the permissions in the folders used by wordpress plugins, I mean, what permissions should I set for the IIS_User in some folders so that the plugins works correctly? What's the best caching plugin to use considering this is a Window Server? In the previous hosting company I used the WPSuperCache, but it was a Linux Stack. Or should I ignore the caching plugins and use the Dynamic Caching Feature of IIS7? How can I optmize the MySQL server running in this server (specially the settings regarding memory and caching) How can I protect the admin folders against hacker attacks? I know some people will advice me not to run Wordpress in a Windows stack, but that's my only choice. I don't even know were to start managing and LAMP stack, don't have the time to do so nor the money to rent another server.

  Read the article

• linux shutdown hang with wifi cifs mounts

  - by Sirex

  Since fedora 15 (and now with 16) it seems that wireless clients take a long while to shutdown when they have network filesystems mounted at shutdown time. I've pushed out a cifs mount via puppet, and all clients have it, including those on wireless. If say a laptop is on a wired connection it shuts down just fine, but if its on the wifi at the time (and no wired connection) it'll hang at the fedora f logo. I'm not sure if its indefinite or just a really long while, but ill give it a test when i shut this machine down in a second. Needless to say its pretty annoying, so is there a way of causing the machine to shutdown even if network connectivity has been lost at unmount time, -- or an official way to reorder events so the wireless card is kept up until after the unmount happens during the shut down process (short of writing a custom script for shutdowns which is a bit of a kludge) ? It does this on multiple machines, and all started doing it when we went from fedora 14 to 15. It was such an obvious issue i'd kind of assumed someone must have reported it or there was an easy fix, but i've not discovered anything yet. Additional info: I can confirm that manually unmounting the mounts then shutting down (sudo shutdown or the xfce shutdown button) will shutdown just fine, it only hangs if the mounts are still mounted The puppet config that sets the mount looks like this (now with the _netdev entry that is indeed pushed to clients successfully, but makes no difference): file { "/mnt/share": ensure = directory,} mount { "/mnt/share": atboot = true, ensure = mounted, remounts = false, fstype = cifs, device = "//srv/share", options = "user,gid=shareusers,uid=${user},file_mode=0700,dir_mode=0700,credentials=/root/.smbcreds,_netdev", require = [ File["/mnt/share"], Group["shareusers"] ], } }

  Read the article

• Maintenance window and recovery for a large database

  - by NYSystemsAnalyst

  One of our teams is developing a database that will be somewhat large (~500GB) and grow from there (I know 500 Gigs may seem small to many of you, but it will be one of the larger databases in our shop). One of the issues they are grappling with is backing up and restoring the database. Basically, the database will have several "data" tables and one table used for storing images / documents. We need to accomplish the following: Be able to quickly backup and restore only the data tables (sans images) to our test server for debugging and testing purposes. In the event of a catastrophic database failure, restore the data tables only to get most of the application up and running ASAP. Then, restore the images table when possible. Backup the database within the allotted nightly time window (a few hours). My questions are: Is it possible to accomplish the first two goals while still having the images stored in the same database? If so, would we use filegroups, filestream, or something else? How do other shops backup their databases in a reasonable time window while maintaining high availability? Do you replicate to a second server and backup from there?

  Read the article

• Mass-migrating from POP3 to Exchange 2010, how do I copy mailboxes?

  - by Erik P. Skaalerud

  I'm in the process of planning our migration from an internal hosted POP3-server (dovecot) to Exchange 2010. We're using Outlook 2003 for the moment, but will soon upgrade to Outlook 2010. The big problem is that we have about 50 computers here in our HQ, plus ~30 clients in branch offices (wich will get their Exchange migration later sometime). I'm the only IT personel, and having to go around and manually set up Outlook and copy over their PST contents is not a option I'm looking for. Some users have set outlook to keep messages for X number of days on the POP3 server, others have not. Using a POP3 connector to transfer over the mails is not a viable option. Here is what I've done so far: Created a transform for the Office 2003 administrative installation point Created a .PRF file to modify any existing e-mail account to switch over to Exchange (including the RPC-encrypt hotfix described in MSKB 2006508) Tested both transform and PRF, both works Created a test-OU and GPO containing the Office 2003 installation with transform applied, also works My big question is: How can I force Outlook to import any existing .PST into the new Exchange mailbox when the user starts up Outlook for the first time after the MST/PRF have been applied? Is this possible?

  Read the article

• Run Python script at startup using upstart

  - by MarcusMaximus

  I'm trying to create an upstart script to run a python script on startup. In theory it looks simple enough but I just can't seem to get it to work. I'm using a skeleton script I found here and altered. description "Used to start python script as a service" author "Me <[email protected]>" # Stanzas # # Stanzas control when and how a process is started and stopped # See a list of stanzas here: http://upstart.ubuntu.com/wiki/Stanzas#respawn # When to start the service start on runlevel [2345] # When to stop the service stop on runlevel [016] # Automatically restart process if crashed respawn # Essentially lets upstart know the process will detach itself to the background expect fork # Start the process script exec python /usr/local/scripts/script.py end script The test script I want it to run is currently a simple python script that runs without any issue when run from a terminal. #!/usr/bin/python2 import os, sys, time if __name__ == "__main__": for i in range (10000): message = "UpstartTest " , i , time.asctime() , " - Username: " , os.getenv("USERNAME") #print message time.sleep(60) out = open("/var/log/scripts/scriptlogfile", "a") print >> out, message out.close() The location/var/log/scripts has permissions 777 The file /usr/local/scripts/script.py has permissions 775 The upstart script /etc/init.d/pythonupstart.conf has permissions 755

  Read the article

• How can use mod_rewrite to redirect a multiple specific URLs containing multiple query strings?

  - by Derek

  Hi there folks, we recently migrated a site from a custom CMS to drupal. In an effort to preserve some links that our users bookmarked (we have about 120 redirects) we would like to forward the original URLs to a new URL. I have been searching for a couple days, but can't seem to find anything simple to what I need. We have existing URLS that contain one or more query strings, for example: /article.php?issue_id=12&article_id=275 and we would like to forward to the new location: http://foobar.edu/content/super-happy-fun-article I started using: RewriteEngine On RewriteRule ^/article\.php?issue_id=12&article_id=275$ http://foobar.edu/content/super-happy-fun-article [R=301,L] This, however, does not work. A simple RewriteRule works: RewriteRule ^test\.php$ index.php It is unclear to me how I need to use {QUERY_STRING} with multiple Basically it's 120 simple redirects that go from one existing URL to a new one. I don't need ranges [0-9], because there is no sequential order to existing URLs. Perhaps I can do what I need with RewriteMap and a simple text file that contains a line like this: index.php?issue_id=12&articleType_section=0&articleType_id=65 http://foobar.edu/category/fall-2008 If anyone has any idea on using mod_rewrite to accomplish this or if there is a better, or more simple mod, I am open to that as well. Thanks!

  Read the article

• Cron job checking for changes in Git repository

  - by HNygard

  We have just moved our server configs to a Git repository. Therefore there should not be any changes in any of the repository folders. I was thinking about how I could set up a cron job to check for any uncommited changes. How could a cron job be set up to check for changes in a Git repository? Greping the output of the git status command might just do it. Grep and cron jobs are not my strong side. Here are some sample outputs from git status: Standing the folder containing the git repository (e.g. /path/gitrepo/) with changed files: $ git status # On branch master # Changes not staged for commit: # (use "git add <file>..." to update what will be committed) # (use "git checkout -- <file>..." to discard changes in working directory) # # modified: apache2/sites-enabled/000-default # # Untracked files: # (use "git add <file>..." to include in what will be committed) # # apache2/conf.d/test no changes added to commit (use "git add" and/or "git commit -a") Standing in the folder when there is no changes: $ git status # On branch master nothing to commit (working directory clean) Update: Synced up with origin is not important. There should be no local changes. Local files that must be in place go into the .gitignore file. In addition to the server configs there are also git repos for content (static web sites, web apps, wordpress, etc). None of the repositories should have local changes. We might use Puppet in the long run since its being used for development of one of the web apps.

  Read the article

• What causes PHP pages to consistently download instead of running normally

  - by Jonathan

  Hi, I'm running a Ubuntu Server on a VM, to test out different web forum solutions. I have set up a ~/public_html/ to be accessible with the apache2 web server, and that works fine. However when I go to a .php file on a browser (using my VM's ip-address/~username/phpfile.php) it does not display it as it should. Instead it offers to save to file/asks what program to open it with. Interestingly though that dialog box does recognise that it is a php file. I have the following version of php installed on the system: PHP 5.3.2-1ubuntu4.5 with Suhosin-Patch (cli) (built: Sep 17 2010 13:49:46) Copyright (c) 1997-2009 The PHP Group Zend Engine v2.3.0, Copyright (c) 1998-2010 Zend Technologies And the following server: Server version: Apache/2.2.14 (Ubuntu) Server built: Nov 18 2010 21:19:09 If anyone knows what might be causing this/potential solutions it would make me very happy :) EDIT: Turns out files this behaviour was only apparent on files in the ~/public_html/ directory. All php files in /var/www/ work fine. Prizes go to whoever can explain why? :D (And by prizes I just mean a well done, no actual prizes I'm afraid.)

  Read the article

• Anyone have real world experience with Rackspace Cloud Sites at high scale?

  - by Allara

  I have a pure web service application layer using .NET. I was originally planning to use Amazon EC2, but rolling my own autoscaling procedures is a bit intimidating, and the scaling isn't very granular from a cost perspective. If the app is successful, we could be looking at relatively high scale (millions of requests per month). The app uses Amazon SimpleDB as the database layer. As a test, I have the app running successfully in Rackspace Cloud Sites. Performance seems to be equal to (if not better than) a standard EC2 instance, even with the added latency of the SimpleDB requests travelling to the Rackspace network. However, testing at this stage is at a very low scale. My question is this: has anyone had real-world experience running a high scale application on Rackspace Cloud Sites? Moreover, once you pass the "included" 10,000 compute cycles per month, does the overall cost seem to be lower than rolling lots of EC2 instances? My assumption would be that with completely smooth scaling (i.e. only adding compute resources as needed), the cost could be lower on average. However, their stated goal of calibrating 10,000 CCs as a single 1.2 Ghz CPU seems on average to be much more expensive than EC2. I like the idea of no-touch scaling, but is it too good to be true?

  Read the article

• Figuring out which PC part is faulty

  - by Davy8

  I have an odd scenario and I'm having trouble figuring out which is the faulty component. First of all, the video doesn't work, monitor says it's not getting a signal. Monitor's not faulty (works on other computer) so the first suspect was video card. However 2 things make me think it's not the video card. (Don't have another machine with PCIe around to test definitively) First, the GPU fan is spinning so it's getting power. Second, tried putting in an older PCI video card that is known to be working (pulled out of another working machine) and there's still no video. Normally if it's not the video card I'd suspect the motherboard, but everything's getting power on the mobo, so I'm not sure. The case apparently doesn't have system speakers, so can't hear any of the diagnostic beeps either. Also not sure whether a faulty CPU would cause no image at all either. The parts are brand new so something's going to get RMA'd but I'm not sure which component is to blame in this case. (Only slightly related, but I also accidentally put too much thermal paste on the CPU. The fan/heatsink instructions said to put the whole tube which seemed like a lot compared to previous experience, and as I started squeezing I knew it was definitely too much and stopped at about 1/3 but against my better judgement I didn't wipe any off. I'm not sure whether that would cause problems other than not cooling as effectively as it should)

  Read the article

• Disaster Recovery Standby Server

  - by user64300

  Hi, I work for a small business with 25 users and 2 servers. 1 server is the DC running Windows Server 2003/Exchange 2003. We want a reliable disaster recovery strategy for this server without having to spend a lot of money. We take regular backups but I have been advised that only an identical server will allow them to be restored easily. I'm trying to come up with a solution that means we don't have to buy two servers at twice the cost everytime we upgrade. I'm toying with the idea of upgrading our DC more frequently (say every 3 years) and then using the old server as the recovery server (temporarily - until we can source a replacement server). However, I won't know whether the backups will restore on the old server until I try it! We're planning to upgrade to Server 2008R2 in the near future so I'm hoping the backup tools will give me some success in restoring to different hardware (or perhaps I can use hyper-v if not). So what I am wondering is whether it is a idea to use old hardware as a disaster recovery strategy (providing we regular test it obviously!).

  Read the article

• How to fix UNMOUNTABLE_BOOT_VOLUME (0x000000ED) on my Windows XP DELL laptop?

  - by Neil

  I have a Dell Latitude D410. Running Windows XP. I am receiving the STOP: 0x000000ED (0X899CF030,0XC0000185,0X00000000,0X00000000) Blue screen. Initially, I tried everything specified with the Microsoft KB articles. At this time, I was able to boot into the general safemode. I pulled the hard drive and was able to run chkdsk on it- it noted that it had fixed some errors, but I was still unable to boot. I put a brand new hard drive in the laptop. Windows XP installation worked up until the reboot, at which time the exact same error message came back up. What I have tried (all since the new hard drive was installed): chkdsk /R All suggested solutions in Microsoft KB articles Reseating RAM Opened laptop, reseated all connectors, looked for signs of damage (saw none) Reset BIOS options to default Ran the basic Dell diagnostics I have looked at the current entry:How can I boot XP after receiving stop error 0x000000ED - I am currently in the process of downloading the Ultimate Boot CD to use as a test, but I am not holding out a lot of hope as I really doubt this brand new Hard Drive is bad. Can anyone think of other areas I am missing? Ran MEMTEST86+ V4.10 for 15 passes (overnight). 0 Errors EDIT: FORMATTING

  Read the article

• WIN7 constant BSOD 0x7B on boot, not producing any dump files where to go from here?

  - by prayingpantis

  So my one win 7 pc has been getting a BSOD on boot (roughly a sec after load screen starts) after a power failure. The complete stop code is 0x0000007B (0x80786B58, 0xC0000034,0x00000000,0x00000000) I've searched for quite a while now on the net and it seems like most people gave up after gettting 0x7B and no dump files. What I've tried so far: startup repair - reports it cannot repair computer automatically. BadPatch is reported somewhere in a problem signature contained in the problem details. startup repair with a WIN 7 CD - also fails, I can't recall what the error was, but it was not the same as the error produced with the start up tool shipped with the version of WIN 7 installed on my machine (I think the text had something ACL-ish contained in it) used a boot disk (Hiren's boot iso) - I used it to enable the CrashDump registry key and then after BSOD, read the HDD's dump locations but it was empty. Note, I'm quite sure the registry keys I edited are the correct ones, since the reboot on BSOD option was enabled by default and after I changed the regkey controlling this functionalitty to 0 the BSOD stayed after I booted again. check disk - works and returns no problems, also it seems I'm able to access all my files on the HDD. mem test - works and returns no errors So I'm not sure what else I can do to figure out what is the problem here. I read somewhere that you can use WINDBG to remote debug another PC, but I'm not sure if this is possible since the OS isn't even loaded yet? Also the last driver change I made on the system was installing a video driver, but I had no problems with it and were able to reboot several times until the power outage happened and the BSOD appeared. Any help or guidance for a way to DEBUG this problem would really be appreciated (I'm not really that keen to try a whole bunch of random fixes, I'd rather try and narrow down the problem first).

  Read the article

• Custom attributes in Active Directory - determining usage/function and possible removal options?

  - by HopelessN00b

  I've bumped into a highly-customized Active Directory environment (2003 FL) that's got me wondering if there's any particularly easy way to figure out what a custom attribute's function is, and what, if anything, is "using" that particular attribute. And then what some good options for potentially removing custom attributes from the schema might be. Aside from a restore or starting from scratch. If such an option exists. For example, I think I can be fairly certain what the "isDumbass" attribute with a value of TRUE means, but not so much with "IRPextCONST", containing a value of 393684. Likewise, I'd think it should be pretty safe to delete the "isDumbass" attribute, but would like to a) be sure and b) find out what's querying or updating that value anyway, because I suspect that anything using that attribute might be next on the list of things to remove. Ideally, without having to run a search on the contents of every custom script and bit of source code I can get my hands on, of course. And finally, aside from rebuilding from scratch, or doing an authoritative AD restore from backups that don't exist... is there a way to delete a given custom attribute? (Not blank the value, but actually delete the attribute from the schema - some folks would rather not have attributes like "FaggotMeter" and "DouchebagCounter" hanging around.) I've been able to find and successfully test a method on Windows 2k, but it seems like Microsoft disabled this option in SP4, and the domain in question is a 2003 functional level.

  Read the article

• Eclipse CDT wont recognize standard library

  - by Mike G

  I work primarily on my desktop, but I started working on my mac laptop and noticed a problem with eclipse CDT. The standard library was underlined yellow and cout wouldn't work (It wouldn't recognize/find it). I tried restarting the program and that didn't work. I then tried to see if xcode would work, found that the version of xcode was too old, and updated xcode. Eclipse still didn't work, but xcode did. I tried re-installing eclipse to the new version and re-installing cdt. It still wouldn't work. Restarting my computer wont work either. I'm not sure if this helps (or even matters/applies) but when I type g++ --version into terminal, it doesn't work. (I don't know if that matters but some tutorial told me to do that to check if the compiler was working). So, in review, I have: Re-installed eclipse Restarted my computer Re-installed xcode (which I think has all the compilers eclipse uses.) Updated Eclipse Typed g++ --version to test compiler.

  Read the article

• Windows Vista freezes

  - by Kakurady

  Windows Vista (32-bit) would randomly freeze on my computer, usually 15-30 minutes after login but can happen just after login. All applications would stop responding and the hard drive will not make any sound, and after a while, the mouse cursor will also stop moving. I dual-boot Ubuntu, and that still works fine. It started with the computer freezing when loading Team Fortress 2. Alt-Tab and Ctrl-Alt-Del have no effect, and the hard drive does not make any sound. I tried to verify the game data using Steam and that freezes the computer too. So I stupidly reinstalled the game. Now the game doesn't freeze when it starts, but instead the whole computer randomly freezes. This computer is a Dell XPS M1530 with a 320GB (298GiB) drive (WDC WD3200BEVT-7) split 5-ways, with Windows and Linux a partition each, one more for Linux swap space, and another two partitions for Dell diagnostic program and factory image and drivers. There was once where the hard drive would make clicking noises all day, and only stopped when I rebooted the computer. Since then, the BIOS diagnostics would fail the drive (for "self-test log contains previous errors") whenever ran. (The on-disk diagnostics cannot be run because I overwrote the MBR with GRUB.) Naturally, I thought the hard drive could be the problem. CHKDSK found one bad sector, but this seems to have no effect. System File Checker found two protected files with wrong hashes, one is some kind of IE manifest, and the other is a tcpmon.ini. Neither of them can be restored because their back up copy also have wrong hashes. Nothing about system failures in the event viewer. What should I do next?

  Read the article

• SQL Server Replication Backup

  - by user18039

  Hi We have a new system that runs on SQL Server 2008 r2 64-bit. There is a primary on-line transactional processing (OLTP) database that accepts a high volume of updates from several thousand Point of Sale systems at stores around the country. In order to protect this vital function, I have decided to introduce a dedicated reporting database server - from which multiple users will run some pretty complex reports. I realise that there were a number of choices but I decided to use Transaction Replication as the mechanism for copying the data from the OLTP database to the new reporting database - one way replication. The solution has worked well in test. I'm now being asked what changes need to be made to the backup policy to cover the architectural changes. I have read pages such as MSDN:Strategies for Backing Up and Restoring Snapshot and Transactional Replication but I think these are overkill for my solution. In fact, my current thinking is that we simply need to continue making backups of the OLTP data and logs. If the Reporting db or any of the system replication (eg distribution) databases fail then it's no big deal - we can clear all down then re-create the replication. I realise that taking a complete snapshot of the OLTP would be time consuming (approx 5 hours) but I'd be more relaxed about this that trying to restore backups of the various data and log files in the correct sequence. My view is that the complex strategies set out in the MSDN article would only be the way to go for a more complex replication solution than I have, eg if there were multiple subscribers with 2-way replication. Would you agree? I'd be grateful for any advice. Many thanks, Rob.,

  Read the article

• Cloning a git repository from a machine running OS X

  - by Mike

  Hi folks, I'm trying to host a git repository from my home OS X machine, and I'm stuck on the last step of cloning the repository from a remote system. Here's what I've done so far: On the OS X (10.6.6) machine (heretofore dubbed the "server") I created a new admin user Logged into the new user's account Installed git Created an empty git repository via "git init" Turned on remote login Set port mapping on my router (airport extreme) to send ssh traffic to the server Added a ".ssh" directory to the user's home directory From the remote machine (also an OS X 10.6.6 machine), I sent that machine's public key to the server using scp and the login credentials of the user created in step 1 To test that the server would use the remote machine's public key, I ssh'd to the server using the username of the user created in step 1 and indeed was able to connect successfully without being asked for a password I installed git on the remote machine From the remote machine I attempted to "git clone ssh://[email protected]:myrepo" (where "user", "my.server.address", and "myrepo" are all replaced by the actual username, server address and repo folder name, respectively) However, every time I try the command in step 11, I get asked to confirm the server's RSA fingerprint, then I'm asked for a password, but the password for the user I set up for that machine never works. Any advice on how to make this work would be greatly appreciated!

  Read the article

• Change the background color of selected text in Google Docs to increase readability [migrated]

  - by gene_wood

  How can I override or change the background color of text selected in Google Docs? It is difficult for me to see the difference and I would like to increase the contrast or difference. After Google restyled Google Docs last year (or earlier this year), I've been unable to see selected text. It's possible this is a visual deficiency with my eyes. In Google Docs, under both Google Chrome (17.0.963.83 (Official Build 127885) m) and Firefox (11.0), when I select text inside a Google Doc, the selected text has a background of color #d6e0f5. Compare this to the default browser background color of #2f65c0. (I determined the color of the selected text background by taking a screenshot and using the color picker tool in Photoshop). I've tested this using a brand new Firefox profile as well as google chrome profile. Here's a section of a screenshot showing the selected text : I've tried using a userscript to override the CSS to go back to the default text selection color using the "Stylish" plugin with this css : ::selection { background:#2f65c0; color:#ffffff; } ::-moz-selection { background:#2f65c0; color:#ffffff; } ::-webkit-selection { background:#2f65c0; color:#ffffff; } This code works on other sites, but I'm unable to get it to work on Google Docs. (I tested on other sites but applying the userscript to a different domain and using bright yellow instead of the default dark blue #2f65c0.) When you use Google Docs, do you have the same color background for selected text or something different? (To test this, browse to docs.google.com , create a document, type text into the document, select the text with the mouse by dragging over it, take a screenshot, load the screenshot up in an image editor and determine the background color of the selected text.) This color differential (between light blue #d6e0f5 and white #fffff) may be easy to see for others and the problem lies with my eyes.

  Read the article

• cannot get mssql working with sql server 2005

  - by Ryan

  I'm a MySQL/Apache user, trying my hand with IIS and SQL server, so please, if this is a stupid question have patience. I'm using IIS version 7.5. PHP version 5.3.13 and SQL server 2005 IIS is running on port 90, not sure if that will make a difference or not. I know my sql server is running because I can explore/connect to it in Server management studio. I know php is configured properly, because //localhost:90/phpinfo.php works fine. I updated the php_msql.dll extension in phpinfo to: extension=ext/php_msql.dll EDIT- However, when I run phpinfo() under the "configure command" row, this is present: --without-mssql I found/downloaded the ntwdblib.dll and placed it in both sys32 and php root. All these things were supposed to fix the issue, and they haven't. This is the code I'm using, straight from php.net: <?php // Server in the this format: <computer>\<instance name> or // <server>,<port> when using a non default port number $server = 'localhost'; // Connect to MSSQL $link = mssql_connect($server, 'uname', 'pwd'); if (!$link) { die('Something went wrong while connecting to MSSQL'); } ?> obviously I'm using a real username and password, but when I load the file in my browser, I receive a 500 error. Upon checking the log, this is what is displayed: 2012-06-25 12:41:29 ::1 GET /test.php - 90 - ::1 Mozilla/5.0+(Windows+NT+6.1;+WOW64)+AppleWebKit/536.5+(KHTML,+like+Gecko)+Chrome/19.0.1084.56+Safari/536.5 500 0 0 5 That (to me) doesn't help me much. What am I doing wrong? Thank you

  Read the article

• MySQL permissions error when showing databases

  - by Tony

  I was trying to install homebrew and very very stupidly did this: sudo chown -R $USER /usr/local The Homebrew instructions say to do this and I'm not much of a sysadmin so I took their word for it. Lesson learned (although I wouldn't really know how to test this...seems like an "undo" script would be super valuable here) Anyway, what is done is done, but now I get this error: $ mysql -u root -p Enter password: Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 548 Server version: 5.1.33 Source distribution Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> show databases; ERROR 1018 (HY000): Can't read dir of '.' (errno: 13) I tried chown-ing back to root with no avail. Does anyone know how I can fix this without reinstalling mysql? Optionally, if I have to reinstall mysql, how can I dump my databases without access to the command line so I don't lose all of my data. Thanks!

  Read the article

< Previous Page | 791 792 793 794 795 796 797 798 799 800 801 802  | Next Page >