Search Results

Search found 26285 results on 1052 pages for 'grant back'.

Page 813/1052 | < Previous Page | 809 810 811 812 813 814 815 816 817 818 819 820  | Next Page >

• Pc freezes then wont boot. The fans spin, but HDD activity light is off

  - by Stuart

  I'm having a problem with my PC and this isn't the first time it's happened. For a few days now, when I turned my PC on, it didn't immediately start to boot up. The monitor said "No signal" and the machine just sat there although the power light was on and the fans were running. Then, after a few minutes, it would begin to boot as if nothing was wrong. Today I started my machine and it ran ok for about 10 minutes. Then the whole thing froze up and I had to shut it down and restart by holding the power button. When it rebooted, the same thing happened again and again and now finally it wont boot up at all. This happened before about 8 months ago. I ended up taking it to the shop after getting a blue screen. They replaced the HDD and upgraded it to windows 7 and it has worked fine since then. However, they charged an arm and a leg for the work and I dont want to have to go back there again. As this is a recurring fault I figure its a mechanical problem of some sort but I'm not sure what. Any ideas? Thanks for your help.

  Read the article

• Bind9 not doing anything with forwarded query responses?

  - by Rykaro

  I have a Bind DNS server that is the local production DNS server and a Windows 2008 R2 domain controller which provides DNS for a lab environment with the domain xyz.lab. I've configured the Bind DNS to forward DNS requests for the domain xyz.lab to the Windows DNS server with this config: zone "xyz.lab" { type forward; forward only; forwarders { x.x.x.x; }; }; zone "x.x.x.in-addr.arpa" { type forward; forward only; forwarders { x.x.x.x; }; }; And Bind options are (the all_internal acl includes the subnets of both the production and lab networks as well as the loopback of the bind server): allow-query { all_internal; }; allow-recursion { all_internal; }; allow-transfer { none; }; notify no; minimal-responses yes; version "unknown"; Unfortunately, when I do an nslookup or dig on the bind server for a host on the lab domain, the request times out. The logs on the Windows 2008 DNS server show it receiving the query and responding to it and a network packet trace shows the query responses arriving at the Bind DNS server. The servers reside on the same switch with a router providing connectivity between the layer 3 subnets (production and lab are on different subnets) and there is a round trip time of between 3ms and 5ms on pings between the two servers, so I don't think there is an issue with latency causing a timeout of the query. In summary a query-response arrives back at the Bind server and the nslookup/dig times-out. Why does the Bind DNS not seem to be doing anything with the query responses when it receives them?

  Read the article

• Anyone have a script to delete a specific local windows profile?

  - by Jordan Weinstein

  I'm looking for Powershell (preferred) script, or .CMD or .VBS, to delete a specific user profile on a workstation (WinXP) or terminal server (2000, '03 or '08). I know all about the delprof utility... That only allows you delete based on a period of inactivity. I want a script to: prompt admin for a username delete that username's profile and to delete the entire profile - registry hive too (not just the folder structure within Documents and Settings). The same way it would if you went to My Computer Properties Advanced tab User Profiles Settings and deleted profiles from there. Any ideas? All I can think of is doing an AD lookup to get the SID of the user specified, then using that to delete the correct registry hive too... something simpler would be nice though... Basically, my HelpDesk used to be local administrators on our Citrix servers and a common fix for various issues was for them to delete a user's profile on the citrix server(s) and have that user log back in - voila, whatever issue they had was resolved. Going forward, in new Citrix environment, they will no longer be local admins on those boxes, but still need to be able to delete profiles (deleting the entire profile: folder and reg hive is key). thanks.

  Read the article

• Linux: How do I use Munin in cPanel to monitor MySQL?

  - by Continuation

  I have a cPanel server running CentOS 5.5. I want to use Munin to monitor MySQL. I went to: Main >> cPanel >> Manage Plugins and selected "Install and keep updated" for Munin and clicked "Save". I got the usual bunch of status updates about the install. At the end I got: Going to read '/home/.cpan/sources/modules/02packages.details.txt.gz' Database was generated on Wed, 02 Mar 2011 18:28:33 GMT ..........................................................................DONE Going to read '/home/.cpan/sources/modules/03modlist.data.gz' Out of memory! Callback called exit. Done Done Done Process Complete As you can see I got an "Out of memory!" message. But after that it said "Process Complete". Was Munin installed? When I went back to "Manage Plugins" it Munin has a check that against "Install and keep updated". So is everything alright? And how do I use Munin now? How do i configure it to monitor MySQL? Where can I see the results? Thanks.

  Read the article

• System Issues and Major Malfuctions after Failed hibernation Exit

  - by Sarah Seguin

  I have a HP G71-340US that went into hibernation mode for a while and when I tried coming out of it, I got an error message: You're computer cannot come out if hibernation . Status: 0xc000009a Info: A fatal error occurred processing the restoration data. File: \hiberfil.sys Any information that was not saved before the computer went into hybernation will be lost enter=continue So I hit continue and it ran soooo super slow it. It was seriously crawling. Finally I gave up and turned it off manually (IE press and hold the button). It's been a week or two since then and EVERY SINGLE TIME I have tried to to do ANYTHING it takes forever. When I say forever, I literally mean takes 5-7 minutes to load the internet, then the page itself, then to click a link, so on so forth. Eventually everything just goes not responding and I have to give up (4-6 HOURS later). I also cannot access my thumb/jump drives once I've managed to load windows. I was going to try runing malware bytes incase of a virus, but it's windows explorer developes errors and goes not responding on me. Currently I'm running scan disk or check disk and like every file is coming back unreadable. I let it run the last 2 hours straight in chkdesk and I'm only at 6 percent with around 500+ errors and still going. Yes, I've taken logs of the errors via cell phone camera and patience. A week or two prior to this happening I had to change our the hard drive due to blunt force trama next to the mouse. OH! Running on Windows 7: ) And I've tried loading the computer in safe mode and it makes absolutely no difference. Any and all help would be appreciated. I really don't know what to do from here and I'm kind of freaking out. I've googled different part of the error and things that I've done/seen and there are so many different answers/topics that I thought it best to just post the questions.

  Read the article

• Creating MS Word 2010 Relative Links?

  - by leeand00

  Okay here is what I've tried so far for creating relative links in my MS Word Documents. In my document from the ribbon I select the File tab. I then select Info from the side bar. Click the properties drop down from the right hand column. (a bit difficult to find initially, since it looks like text not a drop down, but it's there). Click Advanced Properties The <document-name>.docx Properties Dialog Appears I enter .\ to specify that I want a relative path for the links in my document. I click OK. I go back into my document select some text and attempt to make a link out of it clicking the Insert tab of the ribbon, and then clicking Hyperlink. I then select a document from the current folder, and strip the full path from it, leaving just the name of the .docx file to which I wish to link. Then I click OK. The link appears, I try to click it using Ctrl+Click. I am informed that the address of the site is not valid. Check the address and try again. What could I possibly be doing wrong here? I just want a relative link. It's so easy in to do this in HTML.

  Read the article

• Excel controls not visible for certain users

  - by Nossidge

  One of the users of an Excel program I've written is having a weird problem. None of the control objects (Command Button, ComboBox, etc.) are visible to him when he opens the file on his laptop. He is using Excel 2003, the same version I used to create the program, and enables macros using the pop-up when the file loads. I have Googled this, and have found these people who seem to be having the exact same problem, with various versions of Excel. Unfortunately, none of their questions were answered. I can't really explain it any better than this user: If I enter design mode and pull a control from the control toolbar onto a sheet all I see are the drag handles. When not in design mode I have to feel around with the mouse and can click the button which executes the button click code correctly and opens another sheet where again I have to feel around for the buttons to return me to the original sheet. The button I managed to click is now visible but as soon as I click anywhere on the sheet it disappears. I have verified that the visible property of the buttons is set and that the Show All Objects on the Options View tab is selected. If I pull buttons from the Forms toolbar onto a sheet they are visible. If I try to find Objects using F5 when not in design mode Excel reports no objects on the sheet. So, Super Users, can you help? UPDATE: Thanks for your replies, but much like the person in the ozgrid link, the problem has gone away. Not sure why it went, but I can confirm that the user rebooted again and also started up other Excel files that didn't contain controls in the interim. Perhaps that fixed it, or maybe it'll be back again. I'll keep udating with progress, and close if the problem doesn't reoccur for the next few days. Thanks again.

  Read the article

• Clean installation of RHEL 5.5 claims package "desktops" is missing

  - by TKguru42

  Hi all, I'm a student worker in the CS department of my university, so please forgive me for any unprofessional descriptions. Simplified explanations are appreciated. I recently replaced some bad graphics cards in a few public workstations. The machines are all the same model. Before putting them back on the network I did fresh installs of RHEL---first I tried 5.4, but yum update ran into all sorts of ugly dependency errors and if I tried to remove any of the problematic packages, the whole operating system FUBAR'd. Using RHEL 5.5 gave me the same errors during install saying that "java.1.5.1-sun*" and "desktops" were missing, but yum update didn't have any dependency problems. Now that I tried logging in through the GUI, I encounter no GUI past the standard RHEL login page. The desktop is a uniform light teal and there's no system tray. An xclock window and an xterm window are open, and Firefox opens automatically, but that's it. Nothing else. What's REALLY confusing is that the computer claims that gnome is already installed, except it clearly isn't working. Any help or advice is greatly appreciated. If it helps, our department uses kickstart to run our standard Linux installs. I can try to get the script if that would be of use. Thank you!

  Read the article

• How do I prevent lighttpd from caching static files, even when modified on disk?

  - by Pixelastic

  I am using lighttpd to serve static files. I have a bunch of images in a dir that I regularly update. This will change the file content (and filesize) as well as the modification date, but not their filename. When I access the files through http, the updates are not taken into account and lighty serves the old file. I can manually rename the file to something different, then lighttpd will return a 404 error, and if I rename my file back, I will get the correct updated version. Seems like lightty is using some kind of cache mechanism of its own (which is fine) to return static files. Unfortunatly, it seems that this mechanism doesn't update itself when files are modified. I checked through Wireshark, and my browser is really doing a request to the file, this is not a browser caching issue. It returns a 200 OK when requesting it from an empty cache, and a 304 Not Modified otherwise, as expected. But the file is returned with a wrong Last-Modified header that do not reflect the real last modification date. Maybe there is some config directive that I am not aware of ? I would like the files returned by lighty to reflect the changes made on disk directly, or at least being able to invalidate its cache.

  Read the article

• how can a web page change my mouse speed?

  - by Tekaholic

  I usually have many tabs open in Firefox and I haven't been able to find one specific website that causes this because I don't seem to notice it right away. I'm going to click on something on my desktop and I am lifting up the mouse several times to get across the screen. It doesn't seem to matter what program I might be using because this happens on all desktops and in Firefox, too. So I go in my settings and I turn up the mouse speed all the way and it's still not really acceptable. It doesn't matter if I click on different tabs but when I close the browser, my mouse is way too sensitive, like I'd expect at the max setting. Then I go back to Control Center and return my mouse speed and acceleration to normal. When I restart my browser, the mouse remains normal. So is there something to this before I start wasting my time hunting through my history to discover which website or sites are having this effect? ...and if it is a specific site and I locate it, what can I change to stop it's effect on my mouse besides not visiting it? I am using Linux Mint 13 on a box with an AMD Athlon processor and 2gigs of ram. I never installed another browser because everything works for me.

  Read the article

• USB Diskdrive cannot be formatted nor accessed

  - by Dmolish

  So I have just recently bought and 8GB USB stick(Kingston DT 100 G2) on which I had installed Linux. However I needed to reinstall said Linux so I formatted the stick to "default" settings which includes FAT32 filesystem. Later when the install process kept getting errors, I got advice that the problem might be with the FAT filesystem. I decided to try and format the stick to NTSF (format G:/fs:ntsf) but the formatting failed and the drive broke down. And with breaking down I mean you cannot access the drive anymore and when you plug it in Windows asks if I want to format the drive but despite my will the format always fails. To fix this I tried changing it back to FAT32 (format G:/fs:fat32), but i get "Error in IOCTL-call". Second thing I tried was trying to reset the filesystem with some 3rd party application like HP USB Disk Storage Format Tool. But the programs didn´t regocnize any media on the drive. So now I´m in the situation that I haven´t got any idea on what to do next. Is the drive recoverable or did I just create a piece of waste metal.

  Read the article

• Removed Old Domain Trust. Now Progress (9.1D) can't open DB File

  - by RLH

  My company has an old server, running Progress 9.1D on a Windows 2000 VM, which was used by our company OS (Vantage 6 by Epicor.) Vantage was our primary OS for a very long time. About 2 years ago, we migrated to a larger, corporate OS and we cancelled our service contract with Epicor. Yesterday, we removed an AD trust between the corporate domain and our old AD domain we used in the days of Vantage. After restarting the virtual server, I have been able to start the ProService for 9.1D Windows service, however, I can not get Vantage to start back up. When I run the application, I get the error in the message listed below. Transcript: ** Could not connect to server for database [progress db file], errno 0. (1432) How can I fix this? FYI, I haven't had to work with Progress in years and even then I wouldn't have considered myself a "novice"-- I'm even less knowledgeable than that title would suggest. Vantage had a lot of internal tools and I recall that Epicor support managed to prevent .pf scripts from being executed. If there was a Progress specific patch that needed to be applied, you had to do it within the Vantage software OR they had to remote into the machine to fix this. I may not be able to run a .pf script but I do know that I can log into the console-based server application. (Yes, I can't even recall which utility that was called. It is sad.) It's been a long time and I never had to digg into Progress that much. Please help and feel free to ask questions. If you need more info, I'll update this post.

  Read the article

• vim: mapping <control-j> key

  - by bhh1988

  When I'm in insert mode, I sometimes want to be able to move around without using the arrow keys, and without having to go back into normal mode. So in my vimrc I've set up key bindings to do this: imap <C-l> <right> imap <C-h> <left> imap <C-k> <up> imap <C-j> <down> But for some odd reason the only one that doesn't work is the last one, . Doing this in insert mode just gives no response. I'm wondering why this might be, and I just don't know where to even begin looking for the problem. It doesn't appear to be mapped to anything since nothing happens when I do it, whether I'm in the terminal or in gvim. Any pointers would be great! Thanks!

  Read the article

• Windows 7 VPN only works if I connect it to itself first

  - by user1799075

  Just so you have some detail, VPN request are port forwarded from a linksys router hosting the global static IP (to the world) to the windows 7 machine. The ports have been added to the OK list. I have the incoming VPN connection setup on win 7 but the only way it will work from anywhere outside the physical machine is if I connect from itself to itself first. For example, let's say my internal static IP is 10.0.0.50 and incoming VPN server connection IP is 10.0.0.80 (both on the same machine). I can't connect via VPN from anywhere unless I first VPN from the machines .50 address back to itself on the .80 address. Once I do that, I can connect form anywhere, even my phone. It's as if once the machine reboots it thinks it should block requests on .80 until .50 connects first. BitDefender antivirus/firewall is loaded (windows firewall is off) I don't see anywhere to exclude ports in the BitDefender control panel. Maybe this initial connection opens the ports and tags them as safe because the initial request came from the same machine? Any thoughts? It's driving me nuts and I'm sick of having to drive half way across town over to the server, try to get building access and do the initial connection. Please help

  Read the article

• PC doesn't POST with a certain model of PSU

  - by Core Xii

  I have this PC with an Asus P5N32-E SLI motherboard and an Intel Q6600 CPU. I got a new RX-5300 PSU, but it didn't work. The motherboard power LED is on fine When I switch power on, the PC powers up briefly (0.5-1 sec) then shuts down From there on out when I switch power on, it stays on, all fans and components seem to be receiving power, but the motherboard won't POST. No video output, no PC speaker beeps, nothing If I turn the hard switch on the PSU off and then back on again, go to step 2; The PC turns on and then off immediately again, and on subsequent power-ups it stays on but won't POST I disconnected every component but the motherboard, CPU and PSU. Still nothing. I tried three other models of PSU on this PC, both of higher (600) and lower (<300) wattage than the 530 on the RX-5300 and they all work fine. At this point I was convinced the PSU was faulty so I returned it. When the replacement arrived, it behaved exactly the same. So two different units of RX-5300 both with the same symptoms, neither working with this motherboard + CPU. Yet, three other models of PSU work perfectly fine. The PC store couldn't reproduce my problem with the returned PSU. I tried resetting the CMOS with the jumper. I tried with both the 4 and 4+4 (with and without the extra +4 connected) CPU connectors (curiously the RX-5300 comes equipped with both). Could it be a statistical probability that I get two units of the same model of PSU that are faulty in the exact same manner? Could the RX-5300 model itself be somehow incompatible with this motherboard? I was under the impression that PSUs were pretty much universal so long as you have the wattage. Could the motherboard be broken in some such a way as to work with certain PSUs but not others? What's going on here?

  Read the article

• ASP.NET, IS7 and IE8 caching?

  - by jdege

  We're suddenly having problems with some of our sites having old versions of .css and .js files show up in the browser. Generally, these problems go away, when the user clears cache in the browser. Is there something we can do either in the code or in IIS7, to convince the browser to not used the cached files? In our weirdest case, we have one customer whose users hit our site, and get an old version of a js file. They clear cache, load the page, get the current version, and the page runs fine. Then they load the file again, and suddenly have the old version, again. Any ideas as to how that might be happening? I can think of three: The browser is somehow holding on to the old version, when we clear cache, and is putting it back in the cache, before the second page load. One of our servers has an old version of the file, and while the first page load after a clear cache pulls it from one of the servers with the current version, second and subsequent page loads pull it from the server that has the old version. The first load after a clear cache goes straight to our servers, while subsequent loads pull the file from the cache on the customer's web proxy. I have to say, all three of those scenarios seem outlandishly unlikely, but it's a repeatable behavior. Any ideas?

  Read the article

• Referer is passed from HTTPS to HTTP in some cases... How?

  - by ravisorg

  In theory browsers do not pass on referer information from HTTPS to HTTP sites. And in my experience this has always been true. But I just found an exception, and I want to understand why it works so I can use it as well. Search for "what is my referer" on https://www.google.ca/ eg: https://www.google.ca/search?q=what+is+my+referer There are a few sites that will show referer. They all seem to "work" when they shouldn't. For example, click the www.whatismyreferer.com one. I get: Your referer: https://www.google.ca/ Note that sometimes, rarely, I get "no referer" as the result. Go back and click the link again and it'll "work" the next time. This should not happen. www.whatismyreferer.com is a non-HTTPS site. The referer header should not be being passed, but it is. What's going on here, and how can I do the same from my HTTPS site to the HTTP sites I'm linking to?

  Read the article

• What character can be safely used for naming files on unix/linux?

  - by Eric DANNIELOU

  Before yesterday, I used only lower case letters, numbers, dot (.) and underscore(_) for directories and file naming. Today I would like to start using more special characters. Which ones are safe (by safe I mean I will never have any problem)? ps : I can't believe this question hasn't been asked already on this site, but I've searched for the word "naming" and read canonical questions without success (mosts are about computer names). Edit #1 : (btw, I don't use upper case letters for file names. I don't remember why. But since a few month, I have production problems with upper case letters : Some OS do not support ascii!) Here's what happened yesterday at work : As usual, I had to create a self signed SSL certificate. As usual, I used the name of the website for the files : www2.example.com.key www2.example.com.crt www2.example.com.csr. Then comes the problem : Generate a wildcard self signed certificate. I did that and named the files example.com.key example.com.crt example.com.csr, which is misleading (it's a certificate for *.example.com). I came back home, started putting some stars in apache configuration files filenames and see if it works (on a useless home computer, not even stagging). Stars in file names really scares me : Some coworkers/vendors/... can do some script using rm find xarg that would lead to http://www.ucs.cam.ac.uk/support/unix-support/misc/horror, and already one answer talks about disaster. Edit #2 : Just figured that : does not need to be escaped. Anyone knows why it is not used in file names?

  Read the article

• Logging won't stop on log file after renaming/moving it.... how do I stop it?

  - by Jakobud

  Just discovered that logrotate is not rotating our firewall log. So it's up to 12G in size. I need to split up the file into smaller chunks and start manually rotating them so I can get things back on track. However before I start splitting the firewall up, I need to stop the firewall from logging to the current firewall log file and force it to start logging to a new empty file. This way I'm not trying to split up or rotate a log file that is still constantly growing. I tried to simply do this: mv firewall firewall.old touch firewall I expected to see the new empty firewall file to start growing in size, but no... the firewall.old is still be logged to. Then I tried to start/stop iptables. No change. firewall.old is still the log file. I tried to move it to another directory. That didn't help. I tried to stop iptables, then change the filename and create a new firewall file and then start iptables again, but no change. How do I stop the logging on this file and force it to start logging on a new file?

  Read the article

• Nvidia 9800GT randomly prevents computer from booting

  - by Blender

  My computer has been running Windows and Linux perfectly fine with my 9800GT for the past year or so, but today it refused to boot. When I press the power button, this is what happens: Power button flashes once. Fans whir. Graphics card makes clicking noise. Computer reboots. Go back to 1. The cycle just keeps going, and I have to yank the cord to make the computer stop. After about 30 attempts at booting it, the computer powers on and everything works. I'm pretty sure that the graphics card isn't malfunctioning, as I've been GPU computing on it for a while now without any hiccups. But the strange thing is, the computer boots perfectly fine in only 5 boots if I remove the card. The computer is a HP Pavilion a6028x Desktop PC: Processor: AMD Athlon 64 X2 (W) 4600+ 2.4 GHz (AM2 socket) Motherboard: ECS MCP61PM-HM (Nettle 1) RAM: 3GB DDR2 (two different brands) More specs here Does anybody know what could be the problem? Any help or information would be greatly appreciated!

  Read the article

• Multiple Screen - Keyboard Sharing

  - by nhbdesign

  I run a small architectural firm with several drafters employed, I'm currently setting up a new office space and one of the things on top of my list is a figuring out a way to keep tabs on my drafters work and being able to collaborate in real time. Here's the challenge, they sit in a separate large cubicle room and I'm on the other end of the hallway, the way it is now; every time they’ve got some question on how to proceed on a certain design, they would come all the way to my office, I'd open their file (in read only) give some ideas, save-as new file, they go back copy paste... in short, nonsense. What I've been thinking of is to setup a hardwired solution that should enable me to have an extra monitor on my desktop which is hardwired (through KVM or something) to each of my employees workstations serving as a secondary display, so that I can watch live what they do, interact with them just as if they would have an extra keyboard and monitor in my office, except; I don’t want to have on my desk a separate monitor for each employee.. so I'd want them to be tiled on a single large screen, watching all screens alive, and whenever they ask me (or I just decide..) to step in, I just click on any tile and hurray, I'm in, editing and saving in real time on their workstation. I also want to reserve the option when I want to, to just use that monitor as just an extra screen for my workstation. Is something like that possible in 2013? P.S. I know of TeamViewer and similar internet/software based stuff, but I'm specifically looking for something solid hardwired and maintenance free, and also something that would allow to watch without my employees getting notified every time I do so (I’m not a tough boss though...).

  Read the article

• nginx reverse proxy slows down my throughput by half

  - by Isaac A Mosquera

  I'm currently using nginx to proxy back to gunicorn with 8 workers. I'm using an amazon extra large instance with 4 virtual cores. When I connect to gunicorn directly I get about 10K requests/sec. When I serve a static file from nginx I get about 25 requests/sec. But when I place gunicorn behind nginx on the same physical server I get about 5K requests/sec. I understand there will be some latency from nginx, but I think there might be a problem since it's a 50% drops. Anybody heard of something similar? any help would be great! Here is the relevant nginx conf: worker_processes 4; worker_rlimit_nofile 30000; events { worker_connections 5120; } http { sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 65; types_hash_max_size 2048; } sites-enabled/default: upstream backend { server 127.0.0.1:8000; } server { server_name api.domain.com ; location / { proxy_pass http://backend; proxy_buffering off; } }

  Read the article

• Centralized backup method recommendation for SMEs with various OSes

  - by Akinator

  Hi I was wondering what in your opinion is the "best" method for having "everything" backed-up in the following situation. We are a SMEs with 10 computers in total. Three of those computers are MACs The rest are windows (1 vista, 4 win7 and 2 XPs) I'm very open to what the method should be but you should also consider the follwing: Very limited resources Quite "small" bandwidth (4 MBs for all (download) 0.4 MBs (upload, yep, thats it)- though this might get, a little bit better) One of the main thing to back up would be the mails, considerations: All windows computers use outlook, mainly 2003 There is one mac that uses outlook too (for mac of course - not 2011 yet) We also have to backup the files: Not a huge amount Very few very big files Very organizes (by machine) What I would like is to hear your opinions as to which would be the best method (or combination of methods - preferably one of course) considering. We are not sure what do we need and I'm open to suggestions, though an online (cloud based applications) would be great, remember the the bandwidth is unbearable. Last think to consider, it that we would like to do weekly updates (unless the method is very easy of course). Thanks in advance!! I tried to be as specific as possible, but if anything is needed I'll gladly update, please ask for any clarification needed! Please avoid any answers like upgrade all to windows 7 and throw away your macs :) our's may not be an ideal situation, but it is what it is, and right now, it would be impossible for us to change it for a lot of circumstances.

  Read the article

• Windows Update broke Wirless driver - Can't get it working again

  - by private_meta

  I naively installed a driver update incoming from Windows Updates yesterday. That caused my Wifi on my Notebook (HP ELitebook 2740p) to break. The network is working as I tried it with my other mobile devices. When installing said driver, it told me that the installation failed. I tried to do a system restore, which did not help getting wifi connectivity back. The device said it was working, but did not get any wifi connection and did not discover any networks. What I tried next was to uninstall the device from my Device Manager and install either the current drivers found through windows, then I tried the same with the current drivers on the HP driver page. both of those attempts failed. It always tells me that installation failed when I uninstall and reinstall drivers. If I try to update the broken driver via internet, it tells me it is up to date, and in the device manager it still views as broken. Next, I 'played' around a bit and reinstalled drivers, and I managed to install drivers from 2012, and when trying to update drivers manually and picking drivers that match the device, it lets me choose between drivers from 2010 and 2014. 2014 would be the current one, picking the 2010 driver leads to the driver being accepted. However, no wireless network can be found. I'm pretty much out of ideas by now, short of reinstalling. The only option I can still think of was that the device broke at the exact moment I installed the new windows driver, but I find that a bit unlikely. Any help would be appreciated fixing this issue.

  Read the article

• Oracle 11g Data Guard over a WAN

  - by Dave LeJeune

  Hi - We are in process of looking at using Oracle's Data Guard to replicate our 11g instance from a colo facility in Washington DC to Chicago. To give some basics we have approximately 25TB of storage and a healthy transaction rate in the 1-2K/sec range. Also, because we are processing data in real-time we have a 24x7x365 requirement for processing data. We don't have any respites as far as volume except for system upgrades (once every few months) where we take the system offline but then course experience a spike in transactions when we bring the system back on-line. Ideally we would want the second instance in the DG configuration semi-online in a read-only fashion for reports/etc. We evaluated DG in 10g and were not overly impressed and research seemed to show that earlier versions had issues with replication over a WAN but I have heard good things about modifications the product has gone through w/ 11g. Can anyone confirm an instance of this size and transaction rate being replicated over a WAN and if so what is the general latency? An information or experiences with a DG implementation that is of this size and scope would really be helpful (or larger - I also realize we are still relatively small compared to many others out there). Many thanks in advance.

  Read the article

< Previous Page | 809 810 811 812 813 814 815 816 817 818 819 820  | Next Page >